Gypsum was used as substrate,and silica gel was mixed into substrate at a certain mass ratio to prepare humidity-controlling composites;moreover,the moisture absorption and desorption properties of gypsum-based compos...Gypsum was used as substrate,and silica gel was mixed into substrate at a certain mass ratio to prepare humidity-controlling composites;moreover,the moisture absorption and desorption properties of gypsum-based composites were compared with adding different silica gel particle size and proportion.The morphological characteristics,the isothermal equilibrium moisture content curve,moisture absorption and desorption rate,moisture absorption and desorption stability,and humidity-conditioning performance were tested and analyzed.The experimental results show that,compared with pure-gypsum,the surface structure of the gypsum-based composites is relatively loose,the quantity,density and aperture of the pores in the structure increase.The absorption and desorption capacity increase along with the increase of silica gel particle size and silica gel proportion.When 3 mm silica gel particle size is added with a mass ratio of 40%,the maximum equilibrium moisture content of humidity-controlling composites is 0.161 g/g at 98% relative humidity(RH),3.22 times that of pure-gypsum.The moisture absorption and desorption rates are increased,the equilibrium moisture absorption and desorption rates are 2.68 times and 1.61 times that of pure-gypsum at 58.5% RH,respectively.The gypsum-based composites have a good stability,which has better timely response to dynamic humidity changes and can effectively regulate indoor humidity under natural conditions.展开更多
This study focused on the development and characterization of TiO<sub>2</sub>-PES composite fibers with varying TiO<sub>2</sub> loading amounts using a phase inversion process. The resulting co...This study focused on the development and characterization of TiO<sub>2</sub>-PES composite fibers with varying TiO<sub>2</sub> loading amounts using a phase inversion process. The resulting composite fibers exhibited a sponge-like structure with embedded TiO<sub>2</sub> nanoparticles within a polymer matrix. Their photocatalytic performance for ammonia removal from aqueous solutions under UV-A light exposure was thoroughly investigated. The findings revealed that PeTi8 composite fibers displayed superior adsorption capacity compared to other samples. Moreover, the study explored the impact of pH, light intensity, and catalyst dosage on the photocatalytic degradation of ammonia. Adsorption equilibrium isotherms closely followed the Langmuir model, with the results indicating a correlation between qm values of 2.49 mg/g and the porous structure of the adsorbents. The research underscored the efficacy of TiO<sub>2</sub> composite fibers in the photocatalytic removal of aqueous under UV-A light. Notably, increasing the distance between the photocatalyst and the light source resulted in de-creased hydroxyl radical concentration, influencing photocatalytic efficiency. These findings contribute to our understanding of TiO<sub>2</sub> composite fibers as promising photocatalysts for ammonia removal in water treatment applications.展开更多
Porous carbon(PC)is a promising electromagnetic(EM)wave absorbing material thanks to its light weight,large specific surface area as well as good dissipating capacity.To further improve its microwave absorbing perform...Porous carbon(PC)is a promising electromagnetic(EM)wave absorbing material thanks to its light weight,large specific surface area as well as good dissipating capacity.To further improve its microwave absorbing performance,silver coated porous carbon(Ag@PC)is synthesized by one-step hydro-thermal synthesis process making use of fir as a biomass formwork.Phase compositions,morphological structure,and microwave absorption capability of the Ag@PC has been explored.Research results show that the metallic Ag was successfully reduced and the particles are evenly distributed inward the pores of the carbon formwork,which accelerates graphitization process of the amorphous carbon.The Ag@PC composite without adding polyvinyl pyrrolidone(PVP)exhibits higher dielectric constant and better EM wave dissipating capability.This is because the larger particles of Ag give rise to higher electric conductivity.After combing with frequency selective surface(FSS),the EM wave absorbing performance is further improved and the frequency region below-10 d B is located in8.20-11.75 GHz,and the minimal reflection loss value is-22.5 dB.This work indicates that incorporating metallic Ag particles and FSS provides a valid way to strengthen EM wave absorbing capacity of PC material.展开更多
We focused on Ti/Al composite materials fabricated by wire and arc addictive manufacturing,and the microstructure and interface characteristics of them before and after hot compression deformation were compared.After ...We focused on Ti/Al composite materials fabricated by wire and arc addictive manufacturing,and the microstructure and interface characteristics of them before and after hot compression deformation were compared.After compression deformation,allαstructures of titanium were compacted with the emergence of Widmanstatten structures.Coarsened coloniesαof titanium were elongated and waved along the original growth direction,resulting in anisotropy of grains.Pores and Ti/Al intermetallic compounds of aluminum are significantly decreased after hot compression.Meanwhile,a good bonding interface between titanium and aluminum is obtained after hot compression,and the element diffusion is more intense.In addition,the mechanical properties and fracture behaviors of Ti/Al composite material with different clad ratio that is defined as the ratio of the thickness of titanium to that of the Ti/Al composite material are investigated by uniaxial tensile test.The experimental results show that the ultimate tensile strength of Ti/Al composite material is between that of single deposited titanium and aluminum,while the elongation of Ti/Al composite material with low clad ratio is lower than that of single aluminum due to the metallurgical reaction.As the clad ratio increases,the two component layers are harder to separate during deformation,which is resulted from the decrease of the inward contraction stress of three-dimensional stress caused by necking of aluminum.This work may promote the engineering application of Ti/Al bimetallic structures.展开更多
Rolling stock manufacturers are finding structural solutions to reduce power required by the vehicles,and the lightweight design of the car body represents a possible solution.Optimization processes and innovative mat...Rolling stock manufacturers are finding structural solutions to reduce power required by the vehicles,and the lightweight design of the car body represents a possible solution.Optimization processes and innovative materials can be combined in order to achieve this goal.In this framework,we propose the redesign and optimization process of the car body roof for a light rail vehicle,introducing a sandwich structure.Bonded joint was used as a fastening system.The project was carried out on a single car of a modern tram platform.This preliminary numerical work was developed in two main steps:redesign of the car body structure and optimization of the innovated system.Objective of the process was the mass reduction of the whole metallic structure,while the constraint condition was imposed on the first frequency of vibration of the system.The effect of introducing a sandwich panel within the roof assembly was evaluated,focusing on the mechanical and dynamic performances of the whole car body.A mass saving of 63%on the optimized components was achieved,corresponding to a 7.6%if compared to the complete car body shell.In addition,a positive increasing of 17.7%on the first frequency of vibration was observed.Encouraging results have been achieved in terms of weight reduction and mechanical behaviour of the innovated car body.展开更多
This work focused on the search for biobased materials capable of being used in road techniques as soil inclusions, and on studying the influence of their incorporation on the characteristic parameters of pavement lay...This work focused on the search for biobased materials capable of being used in road techniques as soil inclusions, and on studying the influence of their incorporation on the characteristic parameters of pavement layers. To this end, pineapple, cyperus and imperata plant fibers, due to their endemic availability, were used as reinforcement on sourced materials, notably bar soil, lateritic gravel and silty sand. Complete identification and mechanical tests (Proctor and CBR) were carried out on materials in their natural state (soil) and on composite materials (soil + plant fibers) in the laboratory to determine their classification in road geotechnics, their compaction parameters and their mechanical behavior. Firstly, the various types of 2.5 cm long fibers were incorporated into the different types of soil at mass contents of 1% and 2%. This part of the study showed that the pineapple fiber composite incorporated into class A2 bar soil offered the best results, with a 38% gain in CBR index compared with the natural soil. Pineapple fibers incorporated at 1% in lateritic gravel raise the CBR value of the reinforced soil to 10% of the CBR value of the natural soil and to 7% for silty sand.展开更多
The increasing demands for electronic devices to achieve high miniaturization,functional integration,and wide bandwidth will exacerbate the heat generation and electromagnetic interference,which hinders the further de...The increasing demands for electronic devices to achieve high miniaturization,functional integration,and wide bandwidth will exacerbate the heat generation and electromagnetic interference,which hinders the further development of electronic devices.Therefore,both the issues of microwave absorption and heat dissipation of materials need to be addressed simultaneously.Herein,a multifunctional composite material is proposed by periodic arrangement of copper pillars in a matrix,based on the wave-absorbing material.As a result,the equivalent thermal conductivity of the composite structure is nearly 35 times higher than the wave-absorbing matrix,with the area filling proportion of the thermal conductivity material being 3.14%.Meanwhile,the reflectivity of the composite structure merely changes from-15.05 d B to-13.70 d B.It is proved that the designed composite structure possesses both high thermal conduction and strong microwave absorption.The measured results accord well with the simulation results,which demonstrates that the thermal conductivity of the composite structure can reach more than 10 W·m^(-1)·K^(-1)without significant deterioration of the absorption performance.展开更多
Hybrid materials collected from organic and inorganic sources,which are traditionally used as brake lining materials,generally include fly ash,cashew shell powder,phenolic resins,aluminium wool,barites,lime powder,car...Hybrid materials collected from organic and inorganic sources,which are traditionally used as brake lining materials,generally include fly ash,cashew shell powder,phenolic resins,aluminium wool,barites,lime powder,carbon powder and copper powder.The present research focuses on the specific effects produced by fly ash and aims to provide useful indications for the replacement of asbestos due to the health hazards caused by the related fibers.Furthermore,the financial implications related to the use of large-volume use of fly ash,lime stone and cashew shell powder,readily available in most countries in the world,are also discussed.It is shown that many manufacturing and automotive industries,which are currently experiencing difficulties in meeting the increasing demand for brake lining material,may take advantage from the proposed solution.展开更多
As a typical energetic composite,polytetrafluoroethylene(PTFE)/aluminum(Al)has been widely applied in explosives,pyrotechnics,and propellants due to its ultra-high energy density and intense exothermic reaction.In thi...As a typical energetic composite,polytetrafluoroethylene(PTFE)/aluminum(Al)has been widely applied in explosives,pyrotechnics,and propellants due to its ultra-high energy density and intense exothermic reaction.In this work,the radial gradient(RG)structure of PTFE/Al cylinders with three different PTFE morphologies(200 nm and 5μm particles and 5μm fiber)and content changes are prepared by 3D printing technology.The effect of radial gradient structure on the pressure output of PTFE/Al has been studied.Compared with the morphology change of PTFE,the change of component content in the gradient structure has an obvious effect on the pressure output of the PTFE/Al cylinder.Furthermore,the relationships of the morphology,content of PTFE and the combustion reaction of the PTFE/Al cylinder reveal that the cylinder shows a more complex flame propagation process than others.These results could provide a strategy to improve the combustion and pressure output of PTFE/Al.展开更多
In this study, water hyacinth powder-reinforced polymer composites with eggshell filler material are investigated for their mechanical, absorption, morphological, thermal, and characterization properties. Hyacinth pow...In this study, water hyacinth powder-reinforced polymer composites with eggshell filler material are investigated for their mechanical, absorption, morphological, thermal, and characterization properties. Hyacinth powder particles have not been extensively studied in polymer composites. This study investigates the use of eggshell powder for composites made from hyacinth powder. The use of hyacinth powder improves the mechanical properties of composites. With the help of the powder particles, composite samples are produced by compression moulding using an epoxy polymer matrix. 5% eggshell filler varied from 18.25 to 33.64 MPa for tensile strength, 40.28–49.66 MPa for flexural strength, and 2.45–4.75 J for impact strength. X-ray diffraction and Fourier transforms can be used to determine chemical groups, function groups, and crystallinity indexes. Powder particles can be observed by scanning electron microscopes in terms of their bonding behavior, eggshell powder combinations, and primary- and secondary-phase material absorption. According to the research presented in this paper, commercial particleboard applications can benefit substantially from hyacinth powder particles reinforced with eggshell fillers.展开更多
In recent years, additive manufacturing (AM), known as “3D printing”, has experienced exceptional growth thanks to the development of mechatronics and materials science. Fused filament deposition (FDM) manufacturing...In recent years, additive manufacturing (AM), known as “3D printing”, has experienced exceptional growth thanks to the development of mechatronics and materials science. Fused filament deposition (FDM) manufacturing is the most widely used technique in the field of AM, due to low operating and material costs. However, the materials commonly used for this technology are virgin thermoplastics. It is worth noting a considerable amount of waste exists due to failed print and disposable prototypes. In this regard, using green and sustainable materials is essential to limit the impact on the environment. The recycled, bio-based, and blended recycled materials are therefore a potential approach for 3D printing. In contrast, the lack of understanding of the mechanism of interlayer adhesion and the degradation of materials for FDM printing has posed a major challenge for these green materials. This paper provides an overview of the FDM technique and material requirements for 3D printing filaments. The main objective is to highlight the advantages and disadvantages of using recycled, bio-based, and blended materials based on thermoplastics for 3D printing filaments. In this work, solutions to improve the mechanical properties of 3D printing parts before, during, and after the printing process are pointed out. This paper provides an overview on choosing which materials and solutions depend on the specific application purposes. Moreover, research gaps and opportunities are mentioned in the discussion and conclusions sections of this study.展开更多
In this paper, we investigate the properties of an alternative material for use in marine engineering, namely a rigid and light sandwich-structured composite made of expanded polystyrene and fiberglass. Not only does ...In this paper, we investigate the properties of an alternative material for use in marine engineering, namely a rigid and light sandwich-structured composite made of expanded polystyrene and fiberglass. Not only does this material have an improved section modulus, but it is also inexpensive, light, easy to manipulate, and commercially available in various sizes. Using a computer program based on the finite element method, we calculated the hogging and sagging stresses and strains acting on a prismatic boat model composed of this material, and determined the minimum sizes and maximum permissible stresses to avoid deformation. Finally, we calculated the structural weight of the resulting vessel for comparison with another structure of comparable dimensions constructed from the commonly used core material Divinycell.展开更多
An expert system prototype for fibre-reinforced plastic matrix (FRP) composite material design, ESFRP, has been developed. The system consists of seven main functional parts: a general inference engine, a set of knowl...An expert system prototype for fibre-reinforced plastic matrix (FRP) composite material design, ESFRP, has been developed. The system consists of seven main functional parts: a general inference engine, a set of knowledge bases, a material properties algorithm base, an explanation engine, various data bases, several function models and the user interface. The ESFRP can simulate human experts to make design scheme for fibre-reinforced plastics design, FRP layered plates design and FRP typical engineering components design. It can also predict the material properties and make strength analysis according to the micro and macro mechanics of composite materials. A satisfied result can be gained through the reiterative design.展开更多
This article is focused on the investigation of the mechanical and thermal properties of composite material that could be used for the production of plaster or plasterboards.This composite material is made of gypsum a...This article is focused on the investigation of the mechanical and thermal properties of composite material that could be used for the production of plaster or plasterboards.This composite material is made of gypsum and reinforcing natural fibers.The article verifies whether this natural reinforcement can improve the investigated properties compared to conventional plasters and gypsum plasterboards made of pure gypsum.From this composite material,high-strength plasterboards could then be produced,which meet the higher demands of users than conventional gypsum plasterboards.For their production,natural waste materials would be used efficiently.As part of the development of new building materials,it is necessary to specify essential characteristics for their later use in civil engineering.Crushed wheat straw and three gypsum classes with strengths G2(2 MPa)—gypsum Class I.,G5(5 MPa)—gypsum Class II.and G16(16 MPa)—gypsum Class III.were used to create the test samples.Samples were made with different ratios of the two ingredients,with the percentages of straw being 0%,2.5%,and 5%for each gypsum grade.The first part of the article describes how the increasing proportion of straw affects the composite’s mechanical properties(flexural strength and compressive strength).The second part of the article focuses on the change of thermal properties(thermal conductivity and specific heat capacity).The last part of the article mentions the verification of the fire properties(single-flame source fire test and gross heat of combustion)of this composite material.The research has shown that the increasing proportion of straw reinforcement caused a deterioration in the flexural strength(up to 56.49%in the 3.series of gypsum Class II.)and compressive strength(up to 80.27%in the 3.series of gypsum Class III.)and an improvement in the specific heat capacity and thermal conductivity(up to 31.40%in the 3.series).This composite material is thus not suitable for the production of high-strength plasterboards,but its reduced mechanical properties do not prevent its use for interior plasters.Based on the performed fire tests,it can be said that this composite material can be classified as a non-flammable material of reaction to fire Classes A1 or A2.From an ecological point of view,it is advantageous to use a composite material with a higher straw content.展开更多
Bimetallic composite material of bainitic steel and PD3 steel was produced with electroslag casting process, and element distribution of its composite interface was investigated by theoretical calculation and energy d...Bimetallic composite material of bainitic steel and PD3 steel was produced with electroslag casting process, and element distribution of its composite interface was investigated by theoretical calculation and energy dispersive spectrometer(EDS). Results show that the tensile strength(1,450 MPa), hardness(HRC 41-47) and impact toughness(94.7J·cm^(-2)) of bainitic steel were comparatively high, while its elongation was slightly low(4.0%). Tensile strength(1,100 MPa), hardness(>HRC 31) and elongation(7.72%) of the interface were also relatively high, but its impact toughness was low at 20.4 J·cm^(-2). Results of theoretical calculation of the element distribution in the interface region were basically consistent with that of EDS. Therefore, electroslag casting is a practical process to produce bimetallic composite material of bainitic steel and PD3 steel, and theoretical calculation also is a feasible method to study element distribution of their interface.展开更多
Composite materials exhibit advantages from the combination of multiple properties,which cannot be achieved by a monolithic material.At present,the use of composite materials in miniaturized scale is receiving much at...Composite materials exhibit advantages from the combination of multiple properties,which cannot be achieved by a monolithic material.At present,the use of composite materials in miniaturized scale is receiving much attention in the fields of medicine,electronics,aerospace,and microtooling.A common method for producing miniaturized composite parts is micromanufacturing.There has been,however,no comprehensive literature published that reviews,compares,and discusses the ongoing micromanufacturing methods for producing miniaturized composite components.This study identifies the major micromanufacturing methods used with composite materials,categorizes their subclasses,and highlights the latest developments,new trends,and effects of key factors on the productivity,quality,and cost of manufacturing composite materials.A comparative study is presented that shows the potential and versatility associated with producing composite materials along with possible future applications.This review will be helpful in promoting micromanufacturing technology for fabricating miniaturized products made of composite materials to meet the growing industrial demand.展开更多
The technology of Intelligent cure operation is set forth according to developing tedency of smart material and structure. Intelligent-system-based tool was developed in order to operate the autoclave cure of a fiber ...The technology of Intelligent cure operation is set forth according to developing tedency of smart material and structure. Intelligent-system-based tool was developed in order to operate the autoclave cure of a fiber reinforced thermosetting matrix composite laminate in an optimal manner.The objective function is comforts for minimizing the total cure time,uniforming the temperature distribution,controling exothermal and minimizing the process-induced residual stresses in the laminate.Data is analyzed on-line to determine the trends in real-time.The results from application of this overall strategy for the curing of composites are presented.展开更多
With the implementation of new-generation launch vehicles,space stations,lunar and deep space exploration,etc.,the development of spacecraft structures will face new challenges. In order to reduce the spacecraft weigh...With the implementation of new-generation launch vehicles,space stations,lunar and deep space exploration,etc.,the development of spacecraft structures will face new challenges. In order to reduce the spacecraft weight and increase the payload,composite material structures will be widely used. It is difficult to evaluate the strength and life of composite materials due to their complex mechanism and various phenomena in damage and failure.Meanwhile,the structures of composite materials used in spacecrafts will bear complex loads,including the coupling loads of tension,pressure,bending,shear,and torsion. Static loads,thermal loads,and vibration loads may occur at the same time,which asks for verification requirements to ensure the structure safety. Therefore,it is necessary to carry out a systematic multi-level experimental study. In this paper,the building block approach (BBA) is used to investigate the multilevel composite material structures for spacecrafts. The advanced measurement technology is adopted based on digital image correlation (DIC) and piezoelectric and optical fiber sensors to measure the composite material structure deformation. The virtual experiment technology is applied to provide sufficient and reliable data for the evaluation of the composite material structures of spacecrafts.展开更多
The correspondence principle is an important mathematical technique to compute the non-ageing linear viscoelastic problem as it allows to take advantage of the computational methods originally developed for the elasti...The correspondence principle is an important mathematical technique to compute the non-ageing linear viscoelastic problem as it allows to take advantage of the computational methods originally developed for the elastic case. However, the correspondence principle becomes invalid when the materials exhibit ageing. To deal with this problem, a second-order two-scale(SOTS) computational method in the time domain is presented to predict the ageing linear viscoelastic performance of composite materials with a periodic structure. First, in the time domain, the SOTS formulation for calculating the effective relaxation modulus and displacement approximate solutions of the ageing viscoelastic problem is formally derived. Error estimates of the displacement approximate solutions for SOTS method are then given. Numerical results obtained by the SOTS method are shown and compared with those by the finite element method in a very fine mesh. Both the analytical and numerical results show that the SOTS computational method is feasible and efficient to predict the ageing linear viscoelastic performance of composite materials with a periodic structure.展开更多
In this study,the deformation and stress distribution of printed circuit board(PCB)with different thickness and composite materials under a shock loading were analyzed by the finite element analysis.The standard 8-lay...In this study,the deformation and stress distribution of printed circuit board(PCB)with different thickness and composite materials under a shock loading were analyzed by the finite element analysis.The standard 8-layer PCB subjected to a shock loading 1500 g was evaluated first.Moreover,the finite element models of the PCB with different thickness by stacking various number of layers were discussed.In addition to changing thickness,the core material of PCB was replaced from woven E-glass/epoxy to woven carbon fiber/epoxy for structural enhancement.The non-linear material property of copper foil was considered in the analysis.The results indicated that a thicker PCB has lower stress in the copper foil in PCBs under the shock loading.The stress difference between the thicker PCB(2.6 mm)and thinner PCB(0.6 mm)is around 5%.Using woven carbon fiber/epoxy as core material could lower the stress of copper foil around 6.6%under the shock loading 1500 g for the PCB with 0.6 mm thickness.On the other hand,the stress level is under the failure strength of PCBs with carbon fiber/epoxy core layers and thickness 2.6 mm when the peak acceleration changes from 1500 g to 5000 g.This study could provide a reference for the design and proper applications of the PCB with different thickness and composite materials.展开更多
基金Funded by the National Natural Science Foundation of China(No.51678254)。
文摘Gypsum was used as substrate,and silica gel was mixed into substrate at a certain mass ratio to prepare humidity-controlling composites;moreover,the moisture absorption and desorption properties of gypsum-based composites were compared with adding different silica gel particle size and proportion.The morphological characteristics,the isothermal equilibrium moisture content curve,moisture absorption and desorption rate,moisture absorption and desorption stability,and humidity-conditioning performance were tested and analyzed.The experimental results show that,compared with pure-gypsum,the surface structure of the gypsum-based composites is relatively loose,the quantity,density and aperture of the pores in the structure increase.The absorption and desorption capacity increase along with the increase of silica gel particle size and silica gel proportion.When 3 mm silica gel particle size is added with a mass ratio of 40%,the maximum equilibrium moisture content of humidity-controlling composites is 0.161 g/g at 98% relative humidity(RH),3.22 times that of pure-gypsum.The moisture absorption and desorption rates are increased,the equilibrium moisture absorption and desorption rates are 2.68 times and 1.61 times that of pure-gypsum at 58.5% RH,respectively.The gypsum-based composites have a good stability,which has better timely response to dynamic humidity changes and can effectively regulate indoor humidity under natural conditions.
文摘This study focused on the development and characterization of TiO<sub>2</sub>-PES composite fibers with varying TiO<sub>2</sub> loading amounts using a phase inversion process. The resulting composite fibers exhibited a sponge-like structure with embedded TiO<sub>2</sub> nanoparticles within a polymer matrix. Their photocatalytic performance for ammonia removal from aqueous solutions under UV-A light exposure was thoroughly investigated. The findings revealed that PeTi8 composite fibers displayed superior adsorption capacity compared to other samples. Moreover, the study explored the impact of pH, light intensity, and catalyst dosage on the photocatalytic degradation of ammonia. Adsorption equilibrium isotherms closely followed the Langmuir model, with the results indicating a correlation between qm values of 2.49 mg/g and the porous structure of the adsorbents. The research underscored the efficacy of TiO<sub>2</sub> composite fibers in the photocatalytic removal of aqueous under UV-A light. Notably, increasing the distance between the photocatalyst and the light source resulted in de-creased hydroxyl radical concentration, influencing photocatalytic efficiency. These findings contribute to our understanding of TiO<sub>2</sub> composite fibers as promising photocatalysts for ammonia removal in water treatment applications.
基金supported by National Natural Science Foundation of China(No.52103361)Shaanxi University Youth Outstanding Talents Support Plan,Scientific and Technological Plan Project of Xi’an Beilin District(No.GX2143)。
文摘Porous carbon(PC)is a promising electromagnetic(EM)wave absorbing material thanks to its light weight,large specific surface area as well as good dissipating capacity.To further improve its microwave absorbing performance,silver coated porous carbon(Ag@PC)is synthesized by one-step hydro-thermal synthesis process making use of fir as a biomass formwork.Phase compositions,morphological structure,and microwave absorption capability of the Ag@PC has been explored.Research results show that the metallic Ag was successfully reduced and the particles are evenly distributed inward the pores of the carbon formwork,which accelerates graphitization process of the amorphous carbon.The Ag@PC composite without adding polyvinyl pyrrolidone(PVP)exhibits higher dielectric constant and better EM wave dissipating capability.This is because the larger particles of Ag give rise to higher electric conductivity.After combing with frequency selective surface(FSS),the EM wave absorbing performance is further improved and the frequency region below-10 d B is located in8.20-11.75 GHz,and the minimal reflection loss value is-22.5 dB.This work indicates that incorporating metallic Ag particles and FSS provides a valid way to strengthen EM wave absorbing capacity of PC material.
基金Funded by the National Natural Science Foundation of China(No.51775068)。
文摘We focused on Ti/Al composite materials fabricated by wire and arc addictive manufacturing,and the microstructure and interface characteristics of them before and after hot compression deformation were compared.After compression deformation,allαstructures of titanium were compacted with the emergence of Widmanstatten structures.Coarsened coloniesαof titanium were elongated and waved along the original growth direction,resulting in anisotropy of grains.Pores and Ti/Al intermetallic compounds of aluminum are significantly decreased after hot compression.Meanwhile,a good bonding interface between titanium and aluminum is obtained after hot compression,and the element diffusion is more intense.In addition,the mechanical properties and fracture behaviors of Ti/Al composite material with different clad ratio that is defined as the ratio of the thickness of titanium to that of the Ti/Al composite material are investigated by uniaxial tensile test.The experimental results show that the ultimate tensile strength of Ti/Al composite material is between that of single deposited titanium and aluminum,while the elongation of Ti/Al composite material with low clad ratio is lower than that of single aluminum due to the metallurgical reaction.As the clad ratio increases,the two component layers are harder to separate during deformation,which is resulted from the decrease of the inward contraction stress of three-dimensional stress caused by necking of aluminum.This work may promote the engineering application of Ti/Al bimetallic structures.
文摘Rolling stock manufacturers are finding structural solutions to reduce power required by the vehicles,and the lightweight design of the car body represents a possible solution.Optimization processes and innovative materials can be combined in order to achieve this goal.In this framework,we propose the redesign and optimization process of the car body roof for a light rail vehicle,introducing a sandwich structure.Bonded joint was used as a fastening system.The project was carried out on a single car of a modern tram platform.This preliminary numerical work was developed in two main steps:redesign of the car body structure and optimization of the innovated system.Objective of the process was the mass reduction of the whole metallic structure,while the constraint condition was imposed on the first frequency of vibration of the system.The effect of introducing a sandwich panel within the roof assembly was evaluated,focusing on the mechanical and dynamic performances of the whole car body.A mass saving of 63%on the optimized components was achieved,corresponding to a 7.6%if compared to the complete car body shell.In addition,a positive increasing of 17.7%on the first frequency of vibration was observed.Encouraging results have been achieved in terms of weight reduction and mechanical behaviour of the innovated car body.
文摘This work focused on the search for biobased materials capable of being used in road techniques as soil inclusions, and on studying the influence of their incorporation on the characteristic parameters of pavement layers. To this end, pineapple, cyperus and imperata plant fibers, due to their endemic availability, were used as reinforcement on sourced materials, notably bar soil, lateritic gravel and silty sand. Complete identification and mechanical tests (Proctor and CBR) were carried out on materials in their natural state (soil) and on composite materials (soil + plant fibers) in the laboratory to determine their classification in road geotechnics, their compaction parameters and their mechanical behavior. Firstly, the various types of 2.5 cm long fibers were incorporated into the different types of soil at mass contents of 1% and 2%. This part of the study showed that the pineapple fiber composite incorporated into class A2 bar soil offered the best results, with a 38% gain in CBR index compared with the natural soil. Pineapple fibers incorporated at 1% in lateritic gravel raise the CBR value of the reinforced soil to 10% of the CBR value of the natural soil and to 7% for silty sand.
文摘The increasing demands for electronic devices to achieve high miniaturization,functional integration,and wide bandwidth will exacerbate the heat generation and electromagnetic interference,which hinders the further development of electronic devices.Therefore,both the issues of microwave absorption and heat dissipation of materials need to be addressed simultaneously.Herein,a multifunctional composite material is proposed by periodic arrangement of copper pillars in a matrix,based on the wave-absorbing material.As a result,the equivalent thermal conductivity of the composite structure is nearly 35 times higher than the wave-absorbing matrix,with the area filling proportion of the thermal conductivity material being 3.14%.Meanwhile,the reflectivity of the composite structure merely changes from-15.05 d B to-13.70 d B.It is proved that the designed composite structure possesses both high thermal conduction and strong microwave absorption.The measured results accord well with the simulation results,which demonstrates that the thermal conductivity of the composite structure can reach more than 10 W·m^(-1)·K^(-1)without significant deterioration of the absorption performance.
文摘Hybrid materials collected from organic and inorganic sources,which are traditionally used as brake lining materials,generally include fly ash,cashew shell powder,phenolic resins,aluminium wool,barites,lime powder,carbon powder and copper powder.The present research focuses on the specific effects produced by fly ash and aims to provide useful indications for the replacement of asbestos due to the health hazards caused by the related fibers.Furthermore,the financial implications related to the use of large-volume use of fly ash,lime stone and cashew shell powder,readily available in most countries in the world,are also discussed.It is shown that many manufacturing and automotive industries,which are currently experiencing difficulties in meeting the increasing demand for brake lining material,may take advantage from the proposed solution.
基金supported by the National Natural Science Foundation of China(Grant Nos.11872341 and 22075261)。
文摘As a typical energetic composite,polytetrafluoroethylene(PTFE)/aluminum(Al)has been widely applied in explosives,pyrotechnics,and propellants due to its ultra-high energy density and intense exothermic reaction.In this work,the radial gradient(RG)structure of PTFE/Al cylinders with three different PTFE morphologies(200 nm and 5μm particles and 5μm fiber)and content changes are prepared by 3D printing technology.The effect of radial gradient structure on the pressure output of PTFE/Al has been studied.Compared with the morphology change of PTFE,the change of component content in the gradient structure has an obvious effect on the pressure output of the PTFE/Al cylinder.Furthermore,the relationships of the morphology,content of PTFE and the combustion reaction of the PTFE/Al cylinder reveal that the cylinder shows a more complex flame propagation process than others.These results could provide a strategy to improve the combustion and pressure output of PTFE/Al.
文摘In this study, water hyacinth powder-reinforced polymer composites with eggshell filler material are investigated for their mechanical, absorption, morphological, thermal, and characterization properties. Hyacinth powder particles have not been extensively studied in polymer composites. This study investigates the use of eggshell powder for composites made from hyacinth powder. The use of hyacinth powder improves the mechanical properties of composites. With the help of the powder particles, composite samples are produced by compression moulding using an epoxy polymer matrix. 5% eggshell filler varied from 18.25 to 33.64 MPa for tensile strength, 40.28–49.66 MPa for flexural strength, and 2.45–4.75 J for impact strength. X-ray diffraction and Fourier transforms can be used to determine chemical groups, function groups, and crystallinity indexes. Powder particles can be observed by scanning electron microscopes in terms of their bonding behavior, eggshell powder combinations, and primary- and secondary-phase material absorption. According to the research presented in this paper, commercial particleboard applications can benefit substantially from hyacinth powder particles reinforced with eggshell fillers.
文摘In recent years, additive manufacturing (AM), known as “3D printing”, has experienced exceptional growth thanks to the development of mechatronics and materials science. Fused filament deposition (FDM) manufacturing is the most widely used technique in the field of AM, due to low operating and material costs. However, the materials commonly used for this technology are virgin thermoplastics. It is worth noting a considerable amount of waste exists due to failed print and disposable prototypes. In this regard, using green and sustainable materials is essential to limit the impact on the environment. The recycled, bio-based, and blended recycled materials are therefore a potential approach for 3D printing. In contrast, the lack of understanding of the mechanism of interlayer adhesion and the degradation of materials for FDM printing has posed a major challenge for these green materials. This paper provides an overview of the FDM technique and material requirements for 3D printing filaments. The main objective is to highlight the advantages and disadvantages of using recycled, bio-based, and blended materials based on thermoplastics for 3D printing filaments. In this work, solutions to improve the mechanical properties of 3D printing parts before, during, and after the printing process are pointed out. This paper provides an overview on choosing which materials and solutions depend on the specific application purposes. Moreover, research gaps and opportunities are mentioned in the discussion and conclusions sections of this study.
文摘In this paper, we investigate the properties of an alternative material for use in marine engineering, namely a rigid and light sandwich-structured composite made of expanded polystyrene and fiberglass. Not only does this material have an improved section modulus, but it is also inexpensive, light, easy to manipulate, and commercially available in various sizes. Using a computer program based on the finite element method, we calculated the hogging and sagging stresses and strains acting on a prismatic boat model composed of this material, and determined the minimum sizes and maximum permissible stresses to avoid deformation. Finally, we calculated the structural weight of the resulting vessel for comparison with another structure of comparable dimensions constructed from the commonly used core material Divinycell.
基金The work is funded by Heilongjiang Natural Science Foundation of China(No.E9803).
文摘An expert system prototype for fibre-reinforced plastic matrix (FRP) composite material design, ESFRP, has been developed. The system consists of seven main functional parts: a general inference engine, a set of knowledge bases, a material properties algorithm base, an explanation engine, various data bases, several function models and the user interface. The ESFRP can simulate human experts to make design scheme for fibre-reinforced plastics design, FRP layered plates design and FRP typical engineering components design. It can also predict the material properties and make strength analysis according to the micro and macro mechanics of composite materials. A satisfied result can be gained through the reiterative design.
基金This article was financed from the budget of the Student Grant Competition VSB-TUO(Registration No.SGS SP2020/135)This article has been elaborated in the framework of scholarship of the City of Ostrava(RRC/2806/2019)+1 种基金in the framework of the grant programme“Support for Science and Research in the Moravia-Silesia Region 2018”(RRC/10/2018)financed from the budget of the Moravian-Silesian Region.
文摘This article is focused on the investigation of the mechanical and thermal properties of composite material that could be used for the production of plaster or plasterboards.This composite material is made of gypsum and reinforcing natural fibers.The article verifies whether this natural reinforcement can improve the investigated properties compared to conventional plasters and gypsum plasterboards made of pure gypsum.From this composite material,high-strength plasterboards could then be produced,which meet the higher demands of users than conventional gypsum plasterboards.For their production,natural waste materials would be used efficiently.As part of the development of new building materials,it is necessary to specify essential characteristics for their later use in civil engineering.Crushed wheat straw and three gypsum classes with strengths G2(2 MPa)—gypsum Class I.,G5(5 MPa)—gypsum Class II.and G16(16 MPa)—gypsum Class III.were used to create the test samples.Samples were made with different ratios of the two ingredients,with the percentages of straw being 0%,2.5%,and 5%for each gypsum grade.The first part of the article describes how the increasing proportion of straw affects the composite’s mechanical properties(flexural strength and compressive strength).The second part of the article focuses on the change of thermal properties(thermal conductivity and specific heat capacity).The last part of the article mentions the verification of the fire properties(single-flame source fire test and gross heat of combustion)of this composite material.The research has shown that the increasing proportion of straw reinforcement caused a deterioration in the flexural strength(up to 56.49%in the 3.series of gypsum Class II.)and compressive strength(up to 80.27%in the 3.series of gypsum Class III.)and an improvement in the specific heat capacity and thermal conductivity(up to 31.40%in the 3.series).This composite material is thus not suitable for the production of high-strength plasterboards,but its reduced mechanical properties do not prevent its use for interior plasters.Based on the performed fire tests,it can be said that this composite material can be classified as a non-flammable material of reaction to fire Classes A1 or A2.From an ecological point of view,it is advantageous to use a composite material with a higher straw content.
基金financially supported by the Hebei Province Science and Technology Support Program(No.14211007D)
文摘Bimetallic composite material of bainitic steel and PD3 steel was produced with electroslag casting process, and element distribution of its composite interface was investigated by theoretical calculation and energy dispersive spectrometer(EDS). Results show that the tensile strength(1,450 MPa), hardness(HRC 41-47) and impact toughness(94.7J·cm^(-2)) of bainitic steel were comparatively high, while its elongation was slightly low(4.0%). Tensile strength(1,100 MPa), hardness(>HRC 31) and elongation(7.72%) of the interface were also relatively high, but its impact toughness was low at 20.4 J·cm^(-2). Results of theoretical calculation of the element distribution in the interface region were basically consistent with that of EDS. Therefore, electroslag casting is a practical process to produce bimetallic composite material of bainitic steel and PD3 steel, and theoretical calculation also is a feasible method to study element distribution of their interface.
基金The authors would like to thank the Australian Research Council(ARC)for its financial support for the current study.We also acknowledge the use of facilities within the UOW Electron Microscopy Centre.
文摘Composite materials exhibit advantages from the combination of multiple properties,which cannot be achieved by a monolithic material.At present,the use of composite materials in miniaturized scale is receiving much attention in the fields of medicine,electronics,aerospace,and microtooling.A common method for producing miniaturized composite parts is micromanufacturing.There has been,however,no comprehensive literature published that reviews,compares,and discusses the ongoing micromanufacturing methods for producing miniaturized composite components.This study identifies the major micromanufacturing methods used with composite materials,categorizes their subclasses,and highlights the latest developments,new trends,and effects of key factors on the productivity,quality,and cost of manufacturing composite materials.A comparative study is presented that shows the potential and versatility associated with producing composite materials along with possible future applications.This review will be helpful in promoting micromanufacturing technology for fabricating miniaturized products made of composite materials to meet the growing industrial demand.
文摘The technology of Intelligent cure operation is set forth according to developing tedency of smart material and structure. Intelligent-system-based tool was developed in order to operate the autoclave cure of a fiber reinforced thermosetting matrix composite laminate in an optimal manner.The objective function is comforts for minimizing the total cure time,uniforming the temperature distribution,controling exothermal and minimizing the process-induced residual stresses in the laminate.Data is analyzed on-line to determine the trends in real-time.The results from application of this overall strategy for the curing of composites are presented.
文摘With the implementation of new-generation launch vehicles,space stations,lunar and deep space exploration,etc.,the development of spacecraft structures will face new challenges. In order to reduce the spacecraft weight and increase the payload,composite material structures will be widely used. It is difficult to evaluate the strength and life of composite materials due to their complex mechanism and various phenomena in damage and failure.Meanwhile,the structures of composite materials used in spacecrafts will bear complex loads,including the coupling loads of tension,pressure,bending,shear,and torsion. Static loads,thermal loads,and vibration loads may occur at the same time,which asks for verification requirements to ensure the structure safety. Therefore,it is necessary to carry out a systematic multi-level experimental study. In this paper,the building block approach (BBA) is used to investigate the multilevel composite material structures for spacecrafts. The advanced measurement technology is adopted based on digital image correlation (DIC) and piezoelectric and optical fiber sensors to measure the composite material structure deformation. The virtual experiment technology is applied to provide sufficient and reliable data for the evaluation of the composite material structures of spacecrafts.
基金Project supported by the National Natural Science Foundation of China(No.11471262)
文摘The correspondence principle is an important mathematical technique to compute the non-ageing linear viscoelastic problem as it allows to take advantage of the computational methods originally developed for the elastic case. However, the correspondence principle becomes invalid when the materials exhibit ageing. To deal with this problem, a second-order two-scale(SOTS) computational method in the time domain is presented to predict the ageing linear viscoelastic performance of composite materials with a periodic structure. First, in the time domain, the SOTS formulation for calculating the effective relaxation modulus and displacement approximate solutions of the ageing viscoelastic problem is formally derived. Error estimates of the displacement approximate solutions for SOTS method are then given. Numerical results obtained by the SOTS method are shown and compared with those by the finite element method in a very fine mesh. Both the analytical and numerical results show that the SOTS computational method is feasible and efficient to predict the ageing linear viscoelastic performance of composite materials with a periodic structure.
基金the support from Ministry of Science and Technology,Taiwan,R.O.C.,through grant MOST-105-2221-E-007-031-MY3.
文摘In this study,the deformation and stress distribution of printed circuit board(PCB)with different thickness and composite materials under a shock loading were analyzed by the finite element analysis.The standard 8-layer PCB subjected to a shock loading 1500 g was evaluated first.Moreover,the finite element models of the PCB with different thickness by stacking various number of layers were discussed.In addition to changing thickness,the core material of PCB was replaced from woven E-glass/epoxy to woven carbon fiber/epoxy for structural enhancement.The non-linear material property of copper foil was considered in the analysis.The results indicated that a thicker PCB has lower stress in the copper foil in PCBs under the shock loading.The stress difference between the thicker PCB(2.6 mm)and thinner PCB(0.6 mm)is around 5%.Using woven carbon fiber/epoxy as core material could lower the stress of copper foil around 6.6%under the shock loading 1500 g for the PCB with 0.6 mm thickness.On the other hand,the stress level is under the failure strength of PCBs with carbon fiber/epoxy core layers and thickness 2.6 mm when the peak acceleration changes from 1500 g to 5000 g.This study could provide a reference for the design and proper applications of the PCB with different thickness and composite materials.
