Deep rolling is one of the most widely used surface mechanical treatments among several methods used to generate compressive residual stress. This process is usually used for axisymmetric components and can lead to im...Deep rolling is one of the most widely used surface mechanical treatments among several methods used to generate compressive residual stress. This process is usually used for axisymmetric components and can lead to improvements of the surface quality, dimensional accuracy, and mechanical properties. In this study, we deduced the appropriate deep rolling parameters for Al-3vol%Si C nanocomposite samples using roughness and microhardness measurements. The nanocomposite samples were fabricated using a combination of mechanical milling, cold pressing, and hot extrusion techniques. Density measurements indicated acceptable densification of the samples, with no porosity. The results of tensile tests showed that the samples are sufficiently strong for the deep rolling process and also indicated near 50% improvement of tensile strength after incorporating Si C nanoparticle reinforcements. The effects of some important rolling parameters, including the penetration depth, rotation speed, feed rate, and the number of passes, on the surface quality and microhardness were also investigated. The results demonstrated that decreasing the feed rate and increasing the number of passes can lead to greater surface hardness and lower surface roughness.展开更多
A solution-treated AZ91 bulk material was deep-surface-rolled at room temperature to investigate the effect of deep surface rolling on the microstructure and mechanical properties of the alloy. Microhardness and micro...A solution-treated AZ91 bulk material was deep-surface-rolled at room temperature to investigate the effect of deep surface rolling on the microstructure and mechanical properties of the alloy. Microhardness and microstructure along the depth of the treated surface layer were characterized. The results show that the affected layer was up to 2.0 mm thick and consisted of three sublayers: a severe deformation layer with thickness of about 400 μm from the topmost surface, a medium deformation layer with thickness of around 600 μm and a small deformation layer up to 1000 μm thick. In addition to grain refinement in the deformation layer, strain-induced precipitation of β phase (Mg17Al12) was observed, particularly in the severe and medium deformation layers. It is believed that the cooperative effects of grain refinement, strain hardening and precipitation strengthening led to the significant increase in hardness of the AZ91 alloy after the deep surface rolling.展开更多
The issue of determining the maximum compressive residual stress that can be induced through mechanical surface treatment is of great significance.There are two possible approaches,namely stress peening and stress rol...The issue of determining the maximum compressive residual stress that can be induced through mechanical surface treatment is of great significance.There are two possible approaches,namely stress peening and stress rolling,both to determine the limit.Steel with high hardness may be under the yield strength,while for those with lower tensile strength,the hardness is increased,and the limit is above the tensile strength.展开更多
文摘Deep rolling is one of the most widely used surface mechanical treatments among several methods used to generate compressive residual stress. This process is usually used for axisymmetric components and can lead to improvements of the surface quality, dimensional accuracy, and mechanical properties. In this study, we deduced the appropriate deep rolling parameters for Al-3vol%Si C nanocomposite samples using roughness and microhardness measurements. The nanocomposite samples were fabricated using a combination of mechanical milling, cold pressing, and hot extrusion techniques. Density measurements indicated acceptable densification of the samples, with no porosity. The results of tensile tests showed that the samples are sufficiently strong for the deep rolling process and also indicated near 50% improvement of tensile strength after incorporating Si C nanoparticle reinforcements. The effects of some important rolling parameters, including the penetration depth, rotation speed, feed rate, and the number of passes, on the surface quality and microhardness were also investigated. The results demonstrated that decreasing the feed rate and increasing the number of passes can lead to greater surface hardness and lower surface roughness.
基金Project(2016ZE53046)supported by the Aviation Science Foundation of ChinaProject(201606295009)supported by the China Scholarship CouncilProject supported by Top International University Visiting Program for Outstanding Young Scholars of Northwestern Polytechnical University,China
文摘A solution-treated AZ91 bulk material was deep-surface-rolled at room temperature to investigate the effect of deep surface rolling on the microstructure and mechanical properties of the alloy. Microhardness and microstructure along the depth of the treated surface layer were characterized. The results show that the affected layer was up to 2.0 mm thick and consisted of three sublayers: a severe deformation layer with thickness of about 400 μm from the topmost surface, a medium deformation layer with thickness of around 600 μm and a small deformation layer up to 1000 μm thick. In addition to grain refinement in the deformation layer, strain-induced precipitation of β phase (Mg17Al12) was observed, particularly in the severe and medium deformation layers. It is believed that the cooperative effects of grain refinement, strain hardening and precipitation strengthening led to the significant increase in hardness of the AZ91 alloy after the deep surface rolling.
基金funding from the Research Fund for Coal and Steel under grant agreement No.799787。
文摘The issue of determining the maximum compressive residual stress that can be induced through mechanical surface treatment is of great significance.There are two possible approaches,namely stress peening and stress rolling,both to determine the limit.Steel with high hardness may be under the yield strength,while for those with lower tensile strength,the hardness is increased,and the limit is above the tensile strength.
