An ultrahigh vacuum chemical vapor deposition (UHV/CVD) system is developed and the details of its construction and operation are reported. Using high purity SiH4 and GeH4 reactant gases, the Si0.82Ge0.18 layer is dep...An ultrahigh vacuum chemical vapor deposition (UHV/CVD) system is developed and the details of its construction and operation are reported. Using high purity SiH4 and GeH4 reactant gases, the Si0.82Ge0.18 layer is deposited at 550℃. With the measurements by double crystal X-ray diffraction (DCXRD), transmission electron microscopy (TEM) and Rutherford backscattering spectroscopy (RBS) techniques, it is shown that the crystalline quality of the SiGe layer is good, and the underlying SiGe/Si heterointerface is sharply defined.展开更多
.Pulsed Laser Deposition (PLD) is a powerful technique to grow thin films. Oxides, Magnetics and superconducting materials have been obtained by PLD and theirs properties are strongly dependent of deposition parameter....Pulsed Laser Deposition (PLD) is a powerful technique to grow thin films. Oxides, Magnetics and superconducting materials have been obtained by PLD and theirs properties are strongly dependent of deposition parameters. The construction of a simple and cheap PLD system that is suitable for growing various thin films, including magnetic materials, controlling some deposition parameters is presented. The design characteristics and construction are presented for each one of the devices that compose this PLD system. The equipment has the possibility of carrying out films deposition using up to five targets under controlled atmosphere and substrate temperature. The system also allows controlling the cool off sample time after growing up films at high temperatures. A wide range of relative speeds between target and substrate axial rotation can be externally controlled. With the configuration and the dimensions adopted in their construction, a PLD system of great experimental flexibility is achieved, at a very low cost regarding the commercial systems. To evaluate their performance and effectiveness, the deposition characteristics of a BaFe12O19 film on (0001) sapphire substrate is presented.展开更多
Up-scaled deposition process of Teer-UDP850/4 has been established and used for massive production of CrTiAIN hard coatings in applications of anti-wear, cutting and forming tools. This deposition system uses four mag...Up-scaled deposition process of Teer-UDP850/4 has been established and used for massive production of CrTiAIN hard coatings in applications of anti-wear, cutting and forming tools. This deposition system uses four magnetrons that are arranged by unbalanced magnets to form closed magnetic field enabling the system running in high current density. Elemental metals of Cr, Ti and Al are used as the target materials which are co-deposited with nitrogen forming multialloy nitride, nanoscale multi-layer or superlattice hard coatings. The substrate turntable is desfgned as planet rotation mechanism with three folds so that components or tools with complicate geometry can be uniformly coated onto all their surfaces and cutting edges. The power units for the magnetrons are straight dc whilst the substrate is biased by pulsed dc. Two solid heaters are installed in the system to enable running a wide range of deposition temperature from 200°C to 500°C. The pumping system is powerful that incorporated with a polycold to pump the system to a good vacuum in a very short time. A front door and a movable substrate table are available to benefit easily loading and unloading. Deposition procedure, properties and performance of the coatings is also presented in this paper.展开更多
In this work, the wafer bowing during growth can be in-situ measured by a reflectivity mapping method in the 3×2 Thomas Swan close coupled showerhead metal organic chemical vapor deposition(MOCVD) system. The ref...In this work, the wafer bowing during growth can be in-situ measured by a reflectivity mapping method in the 3×2 Thomas Swan close coupled showerhead metal organic chemical vapor deposition(MOCVD) system. The reflectivity mapping method is usually used to measure the film thickness and growth rate. The wafer bowing caused by stresses(tensile and compressive) during the epitaxial growth leads to a temperature variation at different positions on the wafer, and the lower growth temperature leads to a faster growth rate and vice versa. Therefore, the wafer bowing can be measured by analyzing the discrepancy of growth rates at different positions on the wafer. Furthermore, the wafer bowings were confirmed by the ex-situ wafer bowing measurement. High-resistivity and low-resistivity Si substrates were used for epitaxial growth. In comparison with low-resistivity Si substrate, Ga N grown on high-resistivity substrate shows a larger wafer bowing caused by the highly compressive stress introduced by compositionally graded Al Ga N buffer layer. This transition of wafer bowing can be clearly in-situ measured by using the reflectivity mapping method.展开更多
Natural gas hydrate(NGH)can cause pipeline blockages during the transportation of oil and gas under high pressures and low temperatures.Reducing hydrate adhesion on pipelines is viewed as an efficient way to prevent N...Natural gas hydrate(NGH)can cause pipeline blockages during the transportation of oil and gas under high pressures and low temperatures.Reducing hydrate adhesion on pipelines is viewed as an efficient way to prevent NGH blockages.Previous studies suggested the water film can greatly increase hydrate adhesion in gas-dominant system.Herein,by performing the molecular dynamics simulations,we find in water-dominant system,the water film plays different roles in hydrate deposition on Fe and its corrosion surfaces.Specifically,due to the strong affinity of water on Fe surface,the deposited hydrate cannot convert the adsorbed water into hydrate,thus,a water film exists.As water affinities decrease(Fe>Fe_(2)O_(3)>FeO>Fe_(3)O_(4)),adsorbed water would convert to amorphous hydrate on Fe_(2)O_(3)and form the ordered hydrate on FeO and Fe_(3)O_(4)after hydrate deposition.While absorbed water film converts to amorphous or to hydrate,the adhesion strength of hydrate continuously increases(Fe<Fe_(2)O_(3)<FeO<Fe_(3)O_(4)).This is because the detachment of deposited hydrate prefers to occur at soft region of liquid layer,the process of which becomes harder as liquid layer vanishes.As a result,contrary to gas-dominant system,the water film plays the weakening roles on hydrate adhesion in water-dominant system.Overall,our results can help to better understand the hydrate deposition mechanisms on Fe and its corrosion surfaces and suggest hydrate deposition can be adjusted by changing water affinities on pipeline surfaces.展开更多
Pellet injection is a primary method for fueling the plasma in magnetic confinement devices.For that goal the knowledges of pellet ablation and deposition profiles are critical.In the present study,the pellet fueling ...Pellet injection is a primary method for fueling the plasma in magnetic confinement devices.For that goal the knowledges of pellet ablation and deposition profiles are critical.In the present study,the pellet fueling code HPI2 was used to predict the ablation and deposition profiles of deuterium pellets injected into a typical H-mode discharge on the EAST tokamak.Pellet ablation and deposition profiles were evaluated for various pellet injection locations,with the aim at optimizing the pellet injection to obtain a deep fueling depth.In this study,we investigate the effect of the injection angle on the deposition depth of the pellet at different velocities and sizes.The ablation and deposition of the injected pellet are mainly studied at each injection position for three different injection angles:0°,45°,and 60°.The pellet injection on the high field side(HFS)can achieve a more ideal deposition depth than on the low field side(LFS).Among these angles,horizontal injection on the middle plane is relatively better on either the HFS or the LFS.When the injection location is 0.468 m below the middle plane on the HFS or 0.40 m above the middle plane of the LFS,it can achieve a similar deposition depth to the one of its corresponding side.When the pre-cooling effect is taken into account,the deposition depth is predicted to increase only slightly when the pellet is launched from the HFS.The findings of this study will serve as a reference for the update of pellet injection systems for the EAST tokamak.展开更多
Solid polymer electrolyte(SPE) shows great potential for all-solid-state batteries because of the inherent safety and flexibility;however, the unfavourable Li+deposition and large thickness hamper its development and ...Solid polymer electrolyte(SPE) shows great potential for all-solid-state batteries because of the inherent safety and flexibility;however, the unfavourable Li+deposition and large thickness hamper its development and application. Herein, a laminar MXene functional layer-thin SPE layer-cathode integration(MXene-PEO-LFP) is designed and fabricated. The MXene functional layer formed by stacking rigid MXene nanosheets imparts higher compressive strength relative to PEO electrolyte layer. And the abundant negatively-charged groups on MXene functional layer effectively repel anions and attract cations to adjust the charge distribution behavior at electrolyte–anode interface. Furthermore,the functional layer with rich lithiophilic groups and outstanding electronic conductivity results in low Li nucleation overpotential and nucleation energy barrier. In consequence, the cell assembled with MXene-PEO-LFP, where the PEO electrolyte layer is only 12 μm, much thinner than most solid electrolytes, exhibits uniform, dendrite-free Li+deposition and excellent cycling stability. High capacity(142.8 mAh g-1), stable operation of 140 cycles(capacity decay per cycle, 0.065%), and low polarization potential(0.5 C) are obtained in this Li|MXene-PEO-LFP cell,which is superior to most PEO-based electrolytes under identical condition. This integrated design may provide a strategy for the large-scale application of thin polymer electrolytes in all-solid-state battery.展开更多
Asphaltene deposition is a significant problem during gas injection processes,as it can block the porous medium,the wellbore,and the involved facilities,significantly impacting reservoir productivity and ultimate oil re...Asphaltene deposition is a significant problem during gas injection processes,as it can block the porous medium,the wellbore,and the involved facilities,significantly impacting reservoir productivity and ultimate oil recovery.Only a few studies have investigated the numerical modeling of this potential effect in porous media.This study focuses on asphaltene deposition due to natural gas and CO_(2) injection.Predictions of the effect of gas injection on asphaltene deposition behavior have been made using a 3D numerical simulation model.The results indicate that the injection of natural gas exacerbates asphaltene deposition,leading to a significant reduction in permeability near the injection well and throughout the reservoir.This reduction in permeability strongly affects the ability of gas toflow through the reservoir,resulting in an improvement of the displacement front.The displacement effi-ciency of the injection gas process increases by up to 1.40%when gas is injected at 5500 psi,compared to the scenario where the asphaltene model is not considered.CO_(2) injection leads to a miscible process with crude oil,extracting light and intermediate components,which intensifies asphaltene precipitation and increases the viscosity of the remaining crude oil,ultimately reducing the recovery rate.展开更多
Background: To explore the effects of electroacupuncture on cardiac function and myocardial fibrosis in rat models of heart failure, and to elucidate the underlying mechanism of electroacupuncture in heart failure tre...Background: To explore the effects of electroacupuncture on cardiac function and myocardial fibrosis in rat models of heart failure, and to elucidate the underlying mechanism of electroacupuncture in heart failure treatment. Methods: Healthy male Sprague-Dawley rats were allocated into three groups: Sham group, Model group, and electroacupuncture (Model + EA) group, with each group comprising 8 rats. The model underwent a procedure involving the ligation of the left anterior descending coronary artery to induce a model of heart failure. The Model + EA group was used for 7 consecutive days for electroacupuncture of bilateral Shenmen (HT7) and Tongli (HT5), once a day for 30 min each time. Left ventricular parameters in rats were assessed using a small-animal ultrasound machine to analyze changes in left ventricular end-diastolic volume, left ventricular end-systolic volume, left ventricular ejection fraction, and left ventricular fractional shortening. Serum interleukin-1β (IL-1β), cardiac troponin (cTn), and N-terminal brain natriuretic peptide precursor levels were measured using ELISA. Histopathological changes in rat myocardium were observed through HE staining, while collagen deposition in rat myocardial tissue was assessed using the Masson staining method. Picro sirius red staining, immunohistochemical staining, and RT-qPCR were utilized to distinguish between the various types of collagen deposition. The expression level of TGF-β1 and SMAD2/3/4/7 mRNA in rat myocardial tissues was determined using RT-qPCR. Additionally, western blot analysis was conducted to assess the protein expression levels of TGF-β1, SMAD3/7, and p-SMAD3 in rat myocardial tissues. Results: Compared with the Sham group, the left ventricular ejection fraction and left ventricular fractional shortening values of the Model group were significantly decreased (P < 0.01);the left ventricular end-diastolic volume and left ventricular end-systolic volume values were remarkably increased (P < 0.01);serum N-terminal brain natriuretic peptide precursor content was increased (P < 0.01);serum IL-1β and cTn levels were increased (P < 0.01);myocardial collagen volume fraction were increased (P < 0.01);and those of the expression of TGF-β1 and SMAD2/3/4 mRNA was increased (P < 0.01);the expression of SMAD7 mRNA was decreased (P < 0.01);the protein expression levels of TGF-β1, SMAD3, and p-Smad3 were increased (P < 0.01);the protein expression level of SMAD7 was decreased (P < 0.01) in the Model group. Compared to the Model group, the expression levels of the proteins TGF-β1, SMAD3, and p-Smad3 in myocardial tissue were found to be decreased (P < 0.01), and the expression level of the protein SMAD7 was found to be increased (P < 0.01) in the Model + EA group;the collagen volume fraction and deposition of type Ⅰ /Ⅲ collagen were decreased (P < 0.01) in the Model + EA group. Conclusion: Electroacupuncture alleviates myocardial fibrosis in rats with heart failure, and this effect is likely due to attributed to the modulation of the TGF-β1/Smads signaling pathway, which helps reduce collagen deposition in the extracellular matrix.展开更多
Graphene(Gr)has unique properties including high electrical conductivity;Thus,graphene/copper(Gr/Cu)composites have attracted increasing attention to replace traditional Cu for electrical applications. However,the pro...Graphene(Gr)has unique properties including high electrical conductivity;Thus,graphene/copper(Gr/Cu)composites have attracted increasing attention to replace traditional Cu for electrical applications. However,the problem of how to control graphene to form desired Gr/Cu composite is not well solved. This paper aims at exploring the best parameters for preparing graphene with different layers on Cu foil by chemical vapor deposition(CVD)method and studying the effects of different layers graphene on Gr/Cu composite’s electrical conductivity. Graphene grown on single-sided and double-sided copper was prepared for Gr/Cu and Gr/Cu/Gr composites. The resultant electrical conductivity of Gr/Cu composites increased with decreasing graphene layers and increasing graphene volume fraction. The Gr/Cu/Gr composite with monolayer graphene owns volume fraction of less than 0.002%,producing the best electrical conductivity up to59.8 ×10^(6)S/m,equivalent to 104.5% IACS and 105.3% pure Cu foil.展开更多
Dust deposition on the surface of photovoltaic (PV) cells poses a significant challenge to their efficiency, especially in arid regions characterized by desert and semi-desert conditions. Despite the pronounced impact...Dust deposition on the surface of photovoltaic (PV) cells poses a significant challenge to their efficiency, especially in arid regions characterized by desert and semi-desert conditions. Despite the pronounced impact of dust accumulation, these regions offer optimal solar radiation and minimal cloud cover, making them ideal candidates for widespread PV cell deployment. Various surface cleaning methods exist, each employing distinct approaches. Choosing an appropriate cleaning method requires a comprehensive understanding of the mechanisms involved in both dust deposition on module surfaces and dust adhesion to PV cell surfaces. The mechanisms governing dust deposition and adhesion are complex and multifaceted, influenced by factors such as the nature and properties of the dust particles, environmental climatic conditions, characteristics of protective coatings, and the specific location of the PV installation. These factors exhibit regional variations, necessitating the implementation of diverse cleaning approaches tailored to the unique conditions of each location. The first part of this article explores the factors influencing dust deposition on PV cell surfaces, delving into the intricate interplay of environmental variables and particle characteristics. Subsequently, the second part addresses various cleaning methods, offering an analysis of their respective advantages and disadvantages. By comprehensively examining the factors influencing dust accumulation and evaluating the effectiveness of different cleaning strategies, this article aims to contribute valuable insights to the ongoing efforts to optimize the performance and longevity of photovoltaic systems in diverse geographical contexts.展开更多
As an example of atmospheric nitrogen(N) deposition,the paper summarizes the definition,form and amount of nutrient from the environment(NFE) and the relationship between NFE and anthro-pogenic reactive N emission.Bas...As an example of atmospheric nitrogen(N) deposition,the paper summarizes the definition,form and amount of nutrient from the environment(NFE) and the relationship between NFE and anthro-pogenic reactive N emission.Based on our own study and published articles,we find that N wet and dry deposition has been an important nutrient resource in agricultural and natural ecosystems in China.The total amount of N deposition and other environment-derived N in China was up to 18 Tg N/a,equal to ap-proximately 60% of the national N fertilizer consumption.Nitrogen deposition is expected to contribute substantially to nutrient cycling and net primary productivity in various ecosystems.Therefore,it is crucial to utilize this environment-derived nutrient resource by integrated nutrient resource management in order to realize the sustainable development of both agricultural and non-agricultural ecosystems.展开更多
In this study,commercial copper(Cu)foil and Cu foam are used as the working electrodes to systematically investigate the electrochemical deposition and dissolution processes of metallic lithium(Li)on these electrodes;...In this study,commercial copper(Cu)foil and Cu foam are used as the working electrodes to systematically investigate the electrochemical deposition and dissolution processes of metallic lithium(Li)on these electrodes;Li metal deposited on the Cu foil electrode is porous and loose.The surface solid electrolyte interface(SEI)film after dissolution from Li dendrites maintains a dendritic porous structure,resulting in a large volume effect of the electrode during the cycle.The Cu foam electrode provides preferential nucleation and deposition sites near the side surface of the separator;the difference in Li affinity results in a heterogeneous deposition and dendrite growth of metallic Li.展开更多
Using analyses of the lithology,sequences,paleoenvironment,and tectonic setting,the depositional system of the Carboniferous Huanglong Formation in the eastern Sichuan Basin was identified.The lithological characteris...Using analyses of the lithology,sequences,paleoenvironment,and tectonic setting,the depositional system of the Carboniferous Huanglong Formation in the eastern Sichuan Basin was identified.The lithological characteristics of the Lower Member,Middle Member,and Upper Member were analyzed and classified.Before the use of carbon,oxygen,and strontium isotopes in the analysis,all of the geochemical data were tested for validity.On the basis of the Z values obtained from carbon and oxygen isotopes,the paleoenvironments of the three members were elucidated.Lower Member was dominantly an enclosed marine environment with intense evaporation and little freshwater input into the sea.Middle Member developed in a semi-enclosed to normal marine environment with many rivers.Upper Member was formed in a normal marine environment.The east Sichuan Basin was enclosed by paleouplifts before the deposition of the Huanglong Formation,forming a relatively enclosed depositional setting.Paleogullies developed in the Silurian strata that underlie the Carboniferous rocks;these paleogullies can be identified.On the basis of a comprehensive analysis,we propose that the Huanglong Formation developed in a platform system.Four microfacies were identified:supratidal flat,dolostone flat,grain shoal,and shelf microfacies.The high-permeability and high-porosity characteristics of the grain shoal microfacies are favorable for hydrocarbon accumulation,while the supratidal flat and shelf microfacies developed very few high-quality reservoirs.The paleogullies,in which increased amounts of grain shoal microfacies developed,controlled the distribution of high-quality reservoirs.展开更多
Based on the semi-quantitative approach, four environmental factors of sites (i.e. bedrock lithology, soil type, land use, and rainfall) were categorized, weighted and combined to determine and assess the relative sen...Based on the semi-quantitative approach, four environmental factors of sites (i.e. bedrock lithology, soil type, land use, and rainfall) were categorized, weighted and combined to determine and assess the relative sensed of the terrestrial ecosystems to acidic deposition in Fujian Province. Then the factors have been digital and combined to assign an overall value for each mesh square (16.77 km×18.39 km) by using the geographic information system (GIS). The results indicated that the most sensitive area in Fujian was mainly located in the southeast, and the least sensitive area was distributed sporadically in the east along the coast. Due to slow weathering rate of siliceous rocks, acid to weakly acid reactions of the soils, along with the greater percent of coniferous forests, more than 80 percent of the total area exhibits higher sensitivity classes (4-7).展开更多
Ion beam assisted deposition technique (IBAD) was utilized to systematically study amorphization in binary metal systems of Nb-magnetic element, i.e., Nb-M (M=Fe, Co or Ni). The glass forming range termed as Nb fracti...Ion beam assisted deposition technique (IBAD) was utilized to systematically study amorphization in binary metal systems of Nb-magnetic element, i.e., Nb-M (M=Fe, Co or Ni). The glass forming range termed as Nb fraction of Nb-Fe system was about 34at.% to 56at.%, that of Nb-Co system was about 32at.% to 72at.% and that of Nb-Ni about 20at. % to 80at. %. Similar percolation patterns were found in amorphous alloy films. The fractal dimensions of the percolation patterns approach to 2, which indicates 2-D layer growth for amorphous phases. It is regarded that the assisted Ar+ ion beam during the deposition process plays important role for the 2-D layer growth. Some metastable crystalline phases were obtained in these three systems by IBAD, e.g., bcc supersaturated solid solutions in Nb-Fe and Nb-Co systems, fcc and hcp phases in Nb-Co and Nb-Ni systems. The formation and competing between the amorphous and the metastable crystalline phases were determined by both the phases’ thermodynamic states in binary metal systems and kinetics during IBAD process.展开更多
Current situation of air pollution of China is introduced. Critical loads for 4 types of soil in sensitiveareas of China have been calculated using methods of SSMB, Profile Medel and Magic Medel. Maps of criticalload ...Current situation of air pollution of China is introduced. Critical loads for 4 types of soil in sensitiveareas of China have been calculated using methods of SSMB, Profile Medel and Magic Medel. Maps of criticalload , sulfur deposition of 1 990 and excee展开更多
It is a major continuous depocenter in Dalangtan area,western Qaidam basin since Early Cenozoic,which is most important Neogene salt deposits center in Qaidam basin.The Miocene Saline lake was developed firstly
When preparing large monocrystalline silicon materials,severe carbon etching and silicide deposition often occur to the thermal system.Therefore,a suppression method that optimizes the upper insulation structure has b...When preparing large monocrystalline silicon materials,severe carbon etching and silicide deposition often occur to the thermal system.Therefore,a suppression method that optimizes the upper insulation structure has been proposed.Assisted by the finite element method,we calculated temperature distribution and carbon deposition of heater and heat shield,made the rule of silicide and temperature distributing in the system,and we explained the formation of impurity deposition.Our results show that the optimized thermal system reduces carbon etching loss on heat components.The lowered pressure of the furnace brings a rapid decrease of silicide deposition.The increase of the argon flow rate effectively inhibits CO and back diffusion.The simulated results agree well with the experiment observations,validating the effectiveness of the proposed method.展开更多
文摘An ultrahigh vacuum chemical vapor deposition (UHV/CVD) system is developed and the details of its construction and operation are reported. Using high purity SiH4 and GeH4 reactant gases, the Si0.82Ge0.18 layer is deposited at 550℃. With the measurements by double crystal X-ray diffraction (DCXRD), transmission electron microscopy (TEM) and Rutherford backscattering spectroscopy (RBS) techniques, it is shown that the crystalline quality of the SiGe layer is good, and the underlying SiGe/Si heterointerface is sharply defined.
文摘.Pulsed Laser Deposition (PLD) is a powerful technique to grow thin films. Oxides, Magnetics and superconducting materials have been obtained by PLD and theirs properties are strongly dependent of deposition parameters. The construction of a simple and cheap PLD system that is suitable for growing various thin films, including magnetic materials, controlling some deposition parameters is presented. The design characteristics and construction are presented for each one of the devices that compose this PLD system. The equipment has the possibility of carrying out films deposition using up to five targets under controlled atmosphere and substrate temperature. The system also allows controlling the cool off sample time after growing up films at high temperatures. A wide range of relative speeds between target and substrate axial rotation can be externally controlled. With the configuration and the dimensions adopted in their construction, a PLD system of great experimental flexibility is achieved, at a very low cost regarding the commercial systems. To evaluate their performance and effectiveness, the deposition characteristics of a BaFe12O19 film on (0001) sapphire substrate is presented.
文摘Up-scaled deposition process of Teer-UDP850/4 has been established and used for massive production of CrTiAIN hard coatings in applications of anti-wear, cutting and forming tools. This deposition system uses four magnetrons that are arranged by unbalanced magnets to form closed magnetic field enabling the system running in high current density. Elemental metals of Cr, Ti and Al are used as the target materials which are co-deposited with nitrogen forming multialloy nitride, nanoscale multi-layer or superlattice hard coatings. The substrate turntable is desfgned as planet rotation mechanism with three folds so that components or tools with complicate geometry can be uniformly coated onto all their surfaces and cutting edges. The power units for the magnetrons are straight dc whilst the substrate is biased by pulsed dc. Two solid heaters are installed in the system to enable running a wide range of deposition temperature from 200°C to 500°C. The pumping system is powerful that incorporated with a polycold to pump the system to a good vacuum in a very short time. A front door and a movable substrate table are available to benefit easily loading and unloading. Deposition procedure, properties and performance of the coatings is also presented in this paper.
基金Selected from Proceedings of the 7th International Conference on Frontiers of Design and Manufacturing(ICFDM'2006)This project is supported by National Natural Science Foundation of China(No.50475026,No.50275095,No.50575135).
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61274039 and 51177175)the National Basic Research Program of China(Grant No.2011CB301903)+5 种基金the Ph.D.Programs Foundation of Ministry of Education of China(Grant No.20110171110021)the International Science and Technology Collaboration Program of China(Grant No.2012DFG52260)the International Science and Technology Collaboration Program of Guangdong Province,China(Grant No.2013B051000041)the Science and Technology Plan of Guangdong Province,China(Grant No.2013B010401013)the National High Technology Research and Development Program of China(Grant No.2014AA032606)the Opened Fund of the State Key Laboratory on Integrated Optoelectronics,China(Grant No.IOSKL2014KF17)
文摘In this work, the wafer bowing during growth can be in-situ measured by a reflectivity mapping method in the 3×2 Thomas Swan close coupled showerhead metal organic chemical vapor deposition(MOCVD) system. The reflectivity mapping method is usually used to measure the film thickness and growth rate. The wafer bowing caused by stresses(tensile and compressive) during the epitaxial growth leads to a temperature variation at different positions on the wafer, and the lower growth temperature leads to a faster growth rate and vice versa. Therefore, the wafer bowing can be measured by analyzing the discrepancy of growth rates at different positions on the wafer. Furthermore, the wafer bowings were confirmed by the ex-situ wafer bowing measurement. High-resistivity and low-resistivity Si substrates were used for epitaxial growth. In comparison with low-resistivity Si substrate, Ga N grown on high-resistivity substrate shows a larger wafer bowing caused by the highly compressive stress introduced by compositionally graded Al Ga N buffer layer. This transition of wafer bowing can be clearly in-situ measured by using the reflectivity mapping method.
基金This work was supported by the National Natural Science Foundation of China(51874332,51991363)the CNPC's Major Science and Technology Projects(ZD2019-184-003)+1 种基金the Fundamental Research Funds for Central Universities(20CX05008A)“14th Five-Year plan”forward-looking basic major science and technology project of CNPC(2021DJ4901).
文摘Natural gas hydrate(NGH)can cause pipeline blockages during the transportation of oil and gas under high pressures and low temperatures.Reducing hydrate adhesion on pipelines is viewed as an efficient way to prevent NGH blockages.Previous studies suggested the water film can greatly increase hydrate adhesion in gas-dominant system.Herein,by performing the molecular dynamics simulations,we find in water-dominant system,the water film plays different roles in hydrate deposition on Fe and its corrosion surfaces.Specifically,due to the strong affinity of water on Fe surface,the deposited hydrate cannot convert the adsorbed water into hydrate,thus,a water film exists.As water affinities decrease(Fe>Fe_(2)O_(3)>FeO>Fe_(3)O_(4)),adsorbed water would convert to amorphous hydrate on Fe_(2)O_(3)and form the ordered hydrate on FeO and Fe_(3)O_(4)after hydrate deposition.While absorbed water film converts to amorphous or to hydrate,the adhesion strength of hydrate continuously increases(Fe<Fe_(2)O_(3)<FeO<Fe_(3)O_(4)).This is because the detachment of deposited hydrate prefers to occur at soft region of liquid layer,the process of which becomes harder as liquid layer vanishes.As a result,contrary to gas-dominant system,the water film plays the weakening roles on hydrate adhesion in water-dominant system.Overall,our results can help to better understand the hydrate deposition mechanisms on Fe and its corrosion surfaces and suggest hydrate deposition can be adjusted by changing water affinities on pipeline surfaces.
基金supported by the National Natural Science Foundation of China (Grant Nos.12205196 and 12275040)the National Key Research and Development Program of China (Grant No.2022YFE03090003)。
文摘Pellet injection is a primary method for fueling the plasma in magnetic confinement devices.For that goal the knowledges of pellet ablation and deposition profiles are critical.In the present study,the pellet fueling code HPI2 was used to predict the ablation and deposition profiles of deuterium pellets injected into a typical H-mode discharge on the EAST tokamak.Pellet ablation and deposition profiles were evaluated for various pellet injection locations,with the aim at optimizing the pellet injection to obtain a deep fueling depth.In this study,we investigate the effect of the injection angle on the deposition depth of the pellet at different velocities and sizes.The ablation and deposition of the injected pellet are mainly studied at each injection position for three different injection angles:0°,45°,and 60°.The pellet injection on the high field side(HFS)can achieve a more ideal deposition depth than on the low field side(LFS).Among these angles,horizontal injection on the middle plane is relatively better on either the HFS or the LFS.When the injection location is 0.468 m below the middle plane on the HFS or 0.40 m above the middle plane of the LFS,it can achieve a similar deposition depth to the one of its corresponding side.When the pre-cooling effect is taken into account,the deposition depth is predicted to increase only slightly when the pellet is launched from the HFS.The findings of this study will serve as a reference for the update of pellet injection systems for the EAST tokamak.
基金This work is supported by National Natural Science Founda-tion of China(U2004199)National Key Research and Devel-opment Program of China(2018YFD0200606)+1 种基金China Postdoctoral Science Foundation(2021T140615),Natural Sci-enceFoundationofHenanProvince(212300410285)Young Talent Support Project of Henan Province(2021HYTP028).
文摘Solid polymer electrolyte(SPE) shows great potential for all-solid-state batteries because of the inherent safety and flexibility;however, the unfavourable Li+deposition and large thickness hamper its development and application. Herein, a laminar MXene functional layer-thin SPE layer-cathode integration(MXene-PEO-LFP) is designed and fabricated. The MXene functional layer formed by stacking rigid MXene nanosheets imparts higher compressive strength relative to PEO electrolyte layer. And the abundant negatively-charged groups on MXene functional layer effectively repel anions and attract cations to adjust the charge distribution behavior at electrolyte–anode interface. Furthermore,the functional layer with rich lithiophilic groups and outstanding electronic conductivity results in low Li nucleation overpotential and nucleation energy barrier. In consequence, the cell assembled with MXene-PEO-LFP, where the PEO electrolyte layer is only 12 μm, much thinner than most solid electrolytes, exhibits uniform, dendrite-free Li+deposition and excellent cycling stability. High capacity(142.8 mAh g-1), stable operation of 140 cycles(capacity decay per cycle, 0.065%), and low polarization potential(0.5 C) are obtained in this Li|MXene-PEO-LFP cell,which is superior to most PEO-based electrolytes under identical condition. This integrated design may provide a strategy for the large-scale application of thin polymer electrolytes in all-solid-state battery.
基金funded by CNOOC Production Research Project(CCL2022SZPS0076).
文摘Asphaltene deposition is a significant problem during gas injection processes,as it can block the porous medium,the wellbore,and the involved facilities,significantly impacting reservoir productivity and ultimate oil recovery.Only a few studies have investigated the numerical modeling of this potential effect in porous media.This study focuses on asphaltene deposition due to natural gas and CO_(2) injection.Predictions of the effect of gas injection on asphaltene deposition behavior have been made using a 3D numerical simulation model.The results indicate that the injection of natural gas exacerbates asphaltene deposition,leading to a significant reduction in permeability near the injection well and throughout the reservoir.This reduction in permeability strongly affects the ability of gas toflow through the reservoir,resulting in an improvement of the displacement front.The displacement effi-ciency of the injection gas process increases by up to 1.40%when gas is injected at 5500 psi,compared to the scenario where the asphaltene model is not considered.CO_(2) injection leads to a miscible process with crude oil,extracting light and intermediate components,which intensifies asphaltene precipitation and increases the viscosity of the remaining crude oil,ultimately reducing the recovery rate.
基金the China’s National Key Research and Development Program Projects(No.2022YFC3500500 and No.2022YFC3500502).
文摘Background: To explore the effects of electroacupuncture on cardiac function and myocardial fibrosis in rat models of heart failure, and to elucidate the underlying mechanism of electroacupuncture in heart failure treatment. Methods: Healthy male Sprague-Dawley rats were allocated into three groups: Sham group, Model group, and electroacupuncture (Model + EA) group, with each group comprising 8 rats. The model underwent a procedure involving the ligation of the left anterior descending coronary artery to induce a model of heart failure. The Model + EA group was used for 7 consecutive days for electroacupuncture of bilateral Shenmen (HT7) and Tongli (HT5), once a day for 30 min each time. Left ventricular parameters in rats were assessed using a small-animal ultrasound machine to analyze changes in left ventricular end-diastolic volume, left ventricular end-systolic volume, left ventricular ejection fraction, and left ventricular fractional shortening. Serum interleukin-1β (IL-1β), cardiac troponin (cTn), and N-terminal brain natriuretic peptide precursor levels were measured using ELISA. Histopathological changes in rat myocardium were observed through HE staining, while collagen deposition in rat myocardial tissue was assessed using the Masson staining method. Picro sirius red staining, immunohistochemical staining, and RT-qPCR were utilized to distinguish between the various types of collagen deposition. The expression level of TGF-β1 and SMAD2/3/4/7 mRNA in rat myocardial tissues was determined using RT-qPCR. Additionally, western blot analysis was conducted to assess the protein expression levels of TGF-β1, SMAD3/7, and p-SMAD3 in rat myocardial tissues. Results: Compared with the Sham group, the left ventricular ejection fraction and left ventricular fractional shortening values of the Model group were significantly decreased (P < 0.01);the left ventricular end-diastolic volume and left ventricular end-systolic volume values were remarkably increased (P < 0.01);serum N-terminal brain natriuretic peptide precursor content was increased (P < 0.01);serum IL-1β and cTn levels were increased (P < 0.01);myocardial collagen volume fraction were increased (P < 0.01);and those of the expression of TGF-β1 and SMAD2/3/4 mRNA was increased (P < 0.01);the expression of SMAD7 mRNA was decreased (P < 0.01);the protein expression levels of TGF-β1, SMAD3, and p-Smad3 were increased (P < 0.01);the protein expression level of SMAD7 was decreased (P < 0.01) in the Model group. Compared to the Model group, the expression levels of the proteins TGF-β1, SMAD3, and p-Smad3 in myocardial tissue were found to be decreased (P < 0.01), and the expression level of the protein SMAD7 was found to be increased (P < 0.01) in the Model + EA group;the collagen volume fraction and deposition of type Ⅰ /Ⅲ collagen were decreased (P < 0.01) in the Model + EA group. Conclusion: Electroacupuncture alleviates myocardial fibrosis in rats with heart failure, and this effect is likely due to attributed to the modulation of the TGF-β1/Smads signaling pathway, which helps reduce collagen deposition in the extracellular matrix.
基金supported substantially by the Southwest Jiaotong University for Material and Financial Support。
文摘Graphene(Gr)has unique properties including high electrical conductivity;Thus,graphene/copper(Gr/Cu)composites have attracted increasing attention to replace traditional Cu for electrical applications. However,the problem of how to control graphene to form desired Gr/Cu composite is not well solved. This paper aims at exploring the best parameters for preparing graphene with different layers on Cu foil by chemical vapor deposition(CVD)method and studying the effects of different layers graphene on Gr/Cu composite’s electrical conductivity. Graphene grown on single-sided and double-sided copper was prepared for Gr/Cu and Gr/Cu/Gr composites. The resultant electrical conductivity of Gr/Cu composites increased with decreasing graphene layers and increasing graphene volume fraction. The Gr/Cu/Gr composite with monolayer graphene owns volume fraction of less than 0.002%,producing the best electrical conductivity up to59.8 ×10^(6)S/m,equivalent to 104.5% IACS and 105.3% pure Cu foil.
文摘Dust deposition on the surface of photovoltaic (PV) cells poses a significant challenge to their efficiency, especially in arid regions characterized by desert and semi-desert conditions. Despite the pronounced impact of dust accumulation, these regions offer optimal solar radiation and minimal cloud cover, making them ideal candidates for widespread PV cell deployment. Various surface cleaning methods exist, each employing distinct approaches. Choosing an appropriate cleaning method requires a comprehensive understanding of the mechanisms involved in both dust deposition on module surfaces and dust adhesion to PV cell surfaces. The mechanisms governing dust deposition and adhesion are complex and multifaceted, influenced by factors such as the nature and properties of the dust particles, environmental climatic conditions, characteristics of protective coatings, and the specific location of the PV installation. These factors exhibit regional variations, necessitating the implementation of diverse cleaning approaches tailored to the unique conditions of each location. The first part of this article explores the factors influencing dust deposition on PV cell surfaces, delving into the intricate interplay of environmental variables and particle characteristics. Subsequently, the second part addresses various cleaning methods, offering an analysis of their respective advantages and disadvantages. By comprehensively examining the factors influencing dust accumulation and evaluating the effectiveness of different cleaning strategies, this article aims to contribute valuable insights to the ongoing efforts to optimize the performance and longevity of photovoltaic systems in diverse geographical contexts.
基金funded by the One-hundred Talents Program of CAS,the Special Fund for Agricultural Profession (200803030)the Sino-German project (DFG Training Group,GK1070)
文摘As an example of atmospheric nitrogen(N) deposition,the paper summarizes the definition,form and amount of nutrient from the environment(NFE) and the relationship between NFE and anthro-pogenic reactive N emission.Based on our own study and published articles,we find that N wet and dry deposition has been an important nutrient resource in agricultural and natural ecosystems in China.The total amount of N deposition and other environment-derived N in China was up to 18 Tg N/a,equal to ap-proximately 60% of the national N fertilizer consumption.Nitrogen deposition is expected to contribute substantially to nutrient cycling and net primary productivity in various ecosystems.Therefore,it is crucial to utilize this environment-derived nutrient resource by integrated nutrient resource management in order to realize the sustainable development of both agricultural and non-agricultural ecosystems.
基金the National Natural Science Foundation of China(No.51874361)the National Natural Science Foundation of China Youth Fund(51904343)for supporting this work.
文摘In this study,commercial copper(Cu)foil and Cu foam are used as the working electrodes to systematically investigate the electrochemical deposition and dissolution processes of metallic lithium(Li)on these electrodes;Li metal deposited on the Cu foil electrode is porous and loose.The surface solid electrolyte interface(SEI)film after dissolution from Li dendrites maintains a dendritic porous structure,resulting in a large volume effect of the electrode during the cycle.The Cu foam electrode provides preferential nucleation and deposition sites near the side surface of the separator;the difference in Li affinity results in a heterogeneous deposition and dendrite growth of metallic Li.
基金granted by the National Science and Technology Major Project(2011ZX05004-001)
文摘Using analyses of the lithology,sequences,paleoenvironment,and tectonic setting,the depositional system of the Carboniferous Huanglong Formation in the eastern Sichuan Basin was identified.The lithological characteristics of the Lower Member,Middle Member,and Upper Member were analyzed and classified.Before the use of carbon,oxygen,and strontium isotopes in the analysis,all of the geochemical data were tested for validity.On the basis of the Z values obtained from carbon and oxygen isotopes,the paleoenvironments of the three members were elucidated.Lower Member was dominantly an enclosed marine environment with intense evaporation and little freshwater input into the sea.Middle Member developed in a semi-enclosed to normal marine environment with many rivers.Upper Member was formed in a normal marine environment.The east Sichuan Basin was enclosed by paleouplifts before the deposition of the Huanglong Formation,forming a relatively enclosed depositional setting.Paleogullies developed in the Silurian strata that underlie the Carboniferous rocks;these paleogullies can be identified.On the basis of a comprehensive analysis,we propose that the Huanglong Formation developed in a platform system.Four microfacies were identified:supratidal flat,dolostone flat,grain shoal,and shelf microfacies.The high-permeability and high-porosity characteristics of the grain shoal microfacies are favorable for hydrocarbon accumulation,while the supratidal flat and shelf microfacies developed very few high-quality reservoirs.The paleogullies,in which increased amounts of grain shoal microfacies developed,controlled the distribution of high-quality reservoirs.
文摘Based on the semi-quantitative approach, four environmental factors of sites (i.e. bedrock lithology, soil type, land use, and rainfall) were categorized, weighted and combined to determine and assess the relative sensed of the terrestrial ecosystems to acidic deposition in Fujian Province. Then the factors have been digital and combined to assign an overall value for each mesh square (16.77 km×18.39 km) by using the geographic information system (GIS). The results indicated that the most sensitive area in Fujian was mainly located in the southeast, and the least sensitive area was distributed sporadically in the east along the coast. Due to slow weathering rate of siliceous rocks, acid to weakly acid reactions of the soils, along with the greater percent of coniferous forests, more than 80 percent of the total area exhibits higher sensitivity classes (4-7).
基金This work was supported in part by the National Natural Science Foundation of China(Grant No.19875027)the Ministry of Scienc
文摘Ion beam assisted deposition technique (IBAD) was utilized to systematically study amorphization in binary metal systems of Nb-magnetic element, i.e., Nb-M (M=Fe, Co or Ni). The glass forming range termed as Nb fraction of Nb-Fe system was about 34at.% to 56at.%, that of Nb-Co system was about 32at.% to 72at.% and that of Nb-Ni about 20at. % to 80at. %. Similar percolation patterns were found in amorphous alloy films. The fractal dimensions of the percolation patterns approach to 2, which indicates 2-D layer growth for amorphous phases. It is regarded that the assisted Ar+ ion beam during the deposition process plays important role for the 2-D layer growth. Some metastable crystalline phases were obtained in these three systems by IBAD, e.g., bcc supersaturated solid solutions in Nb-Fe and Nb-Co systems, fcc and hcp phases in Nb-Co and Nb-Ni systems. The formation and competing between the amorphous and the metastable crystalline phases were determined by both the phases’ thermodynamic states in binary metal systems and kinetics during IBAD process.
文摘Current situation of air pollution of China is introduced. Critical loads for 4 types of soil in sensitiveareas of China have been calculated using methods of SSMB, Profile Medel and Magic Medel. Maps of criticalload , sulfur deposition of 1 990 and excee
文摘It is a major continuous depocenter in Dalangtan area,western Qaidam basin since Early Cenozoic,which is most important Neogene salt deposits center in Qaidam basin.The Miocene Saline lake was developed firstly
基金supported by the National Natural Science Foundation of China(No.61533014)the Natural Science Foundation of Shaanxi Province(No.2019JQ-734)。
文摘When preparing large monocrystalline silicon materials,severe carbon etching and silicide deposition often occur to the thermal system.Therefore,a suppression method that optimizes the upper insulation structure has been proposed.Assisted by the finite element method,we calculated temperature distribution and carbon deposition of heater and heat shield,made the rule of silicide and temperature distributing in the system,and we explained the formation of impurity deposition.Our results show that the optimized thermal system reduces carbon etching loss on heat components.The lowered pressure of the furnace brings a rapid decrease of silicide deposition.The increase of the argon flow rate effectively inhibits CO and back diffusion.The simulated results agree well with the experiment observations,validating the effectiveness of the proposed method.
