Stitch density is one of the critical quality parameters of knit fabrics. This parameter is closely related to other physical quality parameters like fabric weight, fabric tightness factor, fiber types, blend ratio, y...Stitch density is one of the critical quality parameters of knit fabrics. This parameter is closely related to other physical quality parameters like fabric weight, fabric tightness factor, fiber types, blend ratio, yarn diameter and linear density, and fabric structure. Selecting stitch density (wales per inch, course per inch) is essential to getting the appropriate fabric weight and desired quality. Usually, no rules or assumptions exist to get the desired stitch density in the finished fabric stage. Fifteen types of blended knit fabrics were prepared to conduct the study. The varying percentages of cotton, polyester, and elastane are incorporated in the blends. Regression analysis and regression ANOVA tests were done to predict the stitch density of finished fabrics. A suitable regression equation is established to get the desired results. The study also found that the stitch density value in the finished stage fabric decreases by approximately 15% compared to the stitch density in the grey fabric stage. This study will help the fabric manufacturers get the finished fabric stitch density in advance by utilizing the grey fabric stitch density data set. The author expects this research to benefit the knitting and dyeing industry, new researchers, and advanced researchers.展开更多
The typical micro-knitting structure of knitted fabric,which makes it very different from woven fabric,is described.The tensile tests of knitted fabric are reported.The deformations of the micro-knitting structures ar...The typical micro-knitting structure of knitted fabric,which makes it very different from woven fabric,is described.The tensile tests of knitted fabric are reported.The deformations of the micro-knitting structures are carefully studied.The study indicates that when a knitted fabric sheet is subjected to a tension along w-direction an extra compressive stress field inside loop in c-direction is induced.The extra stress field is also determined through analysis.Finally,a micro-mechanical model of knitted fabric is proposed.This work paves the way for the simulations of buckling modes of a knitted fabric sheet as are observed in experiments.展开更多
Seven kinds of weft knitted fabrics from glass fiber yarns were used as reinforcement to make fabric/epoxy composite laminates. Tensile tests were carried out to examine and compare the mechanical properties in course...Seven kinds of weft knitted fabrics from glass fiber yarns were used as reinforcement to make fabric/epoxy composite laminates. Tensile tests were carried out to examine and compare the mechanical properties in course and wale direction of these composites. On the basis of experimental results, attempts have been made to analyze some main factors influencing stress-strain curve, ultimate tensile strength and initial elastic modulus of specimens.展开更多
A geometric model of relaxed plain-nitted fabric isproposed.A method based on the model for predictingthe loop length from the course spacing,wale spacing offabric and the diameter of yarn is deduced,as well as a comp...A geometric model of relaxed plain-nitted fabric isproposed.A method based on the model for predictingthe loop length from the course spacing,wale spacing offabric and the diameter of yarn is deduced,as well as a computer program is developed to graphically represent the structures of plain knitted fabric with various struc-tural parameters.展开更多
Wet permeability of fibrous assembly is mainly influenced by the properties of liquid and the configurations of the fiber which consist of diameter of fiber, twist angle and fiber alignment in a yarn. It can be seen f...Wet permeability of fibrous assembly is mainly influenced by the properties of liquid and the configurations of the fiber which consist of diameter of fiber, twist angle and fiber alignment in a yarn. It can be seen from experimental results that the knitted fabric made of soybean (SB) fiber has goodproperties both in wet permeability and vapor transmission so that the knitting technology and fabric characteristics can be improved.展开更多
Nowadays,more and more natural or functional fibers are being investigated due to their utilization in thermal underwear.Kapok fiber is one of the natural cellulosic fibers whose source is the kapok plant. It has holl...Nowadays,more and more natural or functional fibers are being investigated due to their utilization in thermal underwear.Kapok fiber is one of the natural cellulosic fibers whose source is the kapok plant. It has hollow body and sealed tail,which exhibits desirable features required for functional textiles of this nature. In this study,cotton / kapok( 80 /20 by mass) blended yarn with two types of yarn size 18. 5 and 14. 8 tex,respectively are knitted into plain stitches. The fabrics are undergone with an optimal preparation plan according to orthogonal design. Then,after dyeing and softening,fabric properties including thermal and water-vapour resistances, wicking property, pilling behaviour, and surface morphology,are tested and scrutinized for their candidacy for thermal underwear. The results showed that cotton / kapok blended fabrics have good thermal resistance which is significantly higher than those of cotton / modal blended fabrics,and the same water vapour resistance compared with cotton / modal blended fabrics which are normally used as underwear. Cotton / modal blended knitted fabrics has better pilling grade than cotton / kapok blended fabrics. Meanwhile, the cotton / kapok blends fabrics have good wicking property. Collectively,it was concluded that cotton / kapok blended fabric was appropriate for thermal underwear. However,the main limitation of these fabrics is their pilling properties.展开更多
With the aid of the micro-mechanical model of knitted fabric proposed in Part 1 we analyze the buckling of a knitted fabric sheet when it is subjected to a tension along the wale direction. The large deformation of th...With the aid of the micro-mechanical model of knitted fabric proposed in Part 1 we analyze the buckling of a knitted fabric sheet when it is subjected to a tension along the wale direction. The large deformation of the fabric sheet in the critical configuration is considered and, to avoid possible deviation due to the approximation of the theory of thin plate, the three-dimensional theory of instability is used. The fabric sheet is considered as a three-dimensional body and all boundary conditions are satisfied. It is shown that the buckling of the fabric sheet is possible, two buckling modes and the corresponding buckling conditions are obtained, but only the flexural mode is physically possible as observed in experiments.展开更多
To improve design capabilities for the knitted fabric pattern,a preliminary study is carried out for the design method.Based on mathematical theory,pattern could be created automatically by computer with inputting dif...To improve design capabilities for the knitted fabric pattern,a preliminary study is carried out for the design method.Based on mathematical theory,pattern could be created automatically by computer with inputting different parameters for mathematical functions.The knitted fabric simulation is realized by M1 CAD pattern preparation system of STOLL Company.In the pattern,different color unit is replaced by obverse stitch with different color,or by obverse stitch and reverse stitch with the same color separately,after that the effects of knitted fabrics could be simulated.Designing with this method,it would not only help to acquire a great of diversity patterns,but also improve design efficiency and save cost.展开更多
Warp knitting technology gets rapid development at present and becomes one of the most important parts of the textiles.But it is less known how the parameters of warp knitting technology affect the mechanical properti...Warp knitting technology gets rapid development at present and becomes one of the most important parts of the textiles.But it is less known how the parameters of warp knitting technology affect the mechanical properties of warp-knitted fabrics.This paper presents discuss a research on the relationships between run-in ratio and mechanical properties of the two-bar warp-knittedfabrics through the measurement and analysis of the mechanical properties of various samples with different run-in ratios.The optimal run一in ratios for the reasonable mechanical properties are obtained from above dis-展开更多
Several different kinds of weft knitted fabrics from glass fiber yarns were used as reinforcement to make fabric/polyester composite laminates. Flexural tests were carried out to examine stress- deflection process and...Several different kinds of weft knitted fabrics from glass fiber yarns were used as reinforcement to make fabric/polyester composite laminates. Flexural tests were carried out to examine stress- deflection process and compare the mechanical properties in course and wale directions of these composites. The experimental results indicate that the numbers of load-bearing yarn in course and wale direction and the fabric density are the main factors influencing the ultimate tensile strength and initial elastic modulus of specimens.展开更多
Pilling is a severe concern for blended fabrics. The aesthetic look and smoothness are the buyers’ prime requirements. The main focus of the study was to see the pilling behavior from various percentages of polyester...Pilling is a severe concern for blended fabrics. The aesthetic look and smoothness are the buyers’ prime requirements. The main focus of the study was to see the pilling behavior from various percentages of polyester fiber blend ratio as well as the different pilling cycles on blended fabrics. The cotton, polyester, and elastane prepared the study fabrics. These fabrics are (90% Cotton/5% Polyester/5% Elastane, 90% Cotton/6% Polyester/4% Elastane, 90% Cotton/7% Polyester/3% Elastane, 90% Cotton/8% Polyester/2% Elastane, and 90% Cotton/9% Polyester/1% Elastane, 85% Cotton/10% Polyester/5% Elastane, 85% Cotton/11% Polyester/4% Elastane, 85% Cotton/12% Polyester/3% Elastane, 85% Cotton/13% Polyester/2% Elastane, and 85% Cotton/ 14% Polyester/1% Elastane, 80% Cotton/15% Polyester/5% Elastane, 80% Cotton/16% Polyester/4% Elastane, 80% Cotton/17% Polyester/3% Elastane, 80% Cotton/18% Polyester/2% Elastane, and 80% Cotton/19% Polyester/1% Elastane). The selected polyester blend ratios were 5%, 6%, 7%, 8%, 9%, 10%, 11%, 12%, 13%, 14%, 15%, 16%, 17%, 18% and 19% respectively. The study used the Martindale pilling tester with 2000, 5000, and 7000 cycles, respectively. The evaluation followed the ISO 12945-2:2000. The study findings are that the polyester fiber blend ratio did not influence the pilling grade on blended fabrics for pilling cycles 2000, and the pilling grade remained constant at 4 - 5. The pilling grade started to deteriorate in pilling cycle 5000 for the fabrics 85%C/10%P/5%E, 85%C/11%P/4%E, 85%C/12%P/3%E, 85%C/ 13%P/2%E, 85%C/14%P/1%E showed the pilling grade 4, and the fabrics made from 80%C/15%P/5%E, 80%C/16%P/4%E, 80%C/17%P/3%E, 80%C/ 18%P/2%E, 80%C/19%P/1%E showed the pilling grade 4, 3, 3, 3, and 3 respectively. For the pilling cycles 7000, the pilling grade further deteriorated for the fabrics 80%C/15%P/5%E, 80%C/16%P/4%E, 80%C/17%P/3%E, 80%C/ 18%P/2%E, 80%C/19%P/1%E showed the pilling grade 3, 3, 2, 2, and 2 respectively. The study finds the dominance of polyester fiber throughout the experiment. The author hopes this study’s outcome will help new researchers, advanced researchers, and the textile industry’s sustainable development research and development team.展开更多
In this paper, dyeing processes of silk-like fabric of ultra-fine polyester fiber are studied through orthogonal experiment, dyeing properties (K/S value, L* value, and C* value) of the fabric are tested under differe...In this paper, dyeing processes of silk-like fabric of ultra-fine polyester fiber are studied through orthogonal experiment, dyeing properties (K/S value, L* value, and C* value) of the fabric are tested under different dyeing conditions (pH value, time, and bath ratlo), and optimum dyeing conditions are arrived at through analysis.展开更多
This paper introduces the construction of the multi-layered biaxial weft knitted fabric （MBWK fabric） and studies the locking angle of this kind of fabric. Moreover, a locking angle model of the MBWK fabric is estab...This paper introduces the construction of the multi-layered biaxial weft knitted fabric （MBWK fabric） and studies the locking angle of this kind of fabric. Moreover, a locking angle model of the MBWK fabric is established for the first time according to its unique construction. Two kinds of locking angles are considered under different restraint conditions: the locking angle θ1 controlled by the inserting yarns and the locking angle θ2 controlled by the stitch yarns. It is concluded that the ultimate value of the locking angle θ is the larger one of the two angles.展开更多
The outbreak of coronavirus has led to an increase in the demand for facemasks globally. Unavailability of appropriate polypropylene non-woven fabrics face masks as a result of inadequate supply to satisfy the growing...The outbreak of coronavirus has led to an increase in the demand for facemasks globally. Unavailability of appropriate polypropylene non-woven fabrics face masks as a result of inadequate supply to satisfy the growing population has brought about the manufacturing of locally fabrics masks to augment or substitute standard medical class facemasks. The study aims at analyzing airflow of these locally manufactured fabrics to determine possible means of transmitting the virus as well as establish comfort of the user of these masks. Standard polypropylene non-woven, woven and knitted fabrics were considered for the study. Air permeability test was conducted on these fabrics using Frazier Air permeability tester. Depending on the property significant variation in the textile fabrics, polypropylene non-woven is widely accepted for facial masks. Nevertheless, this study illustrates that woven and knitted fabrics have more open structures, which allow a high rate of air penetration and so may require two or three layers to prevent antimicrobial or antiviral potential.展开更多
In order to realize parametric simulation of three-dimensional(3D)fabric structure based on web,a 3D model describing a plain knitted fabric,in which the cross-section of the yarn is circular shape and the path of the...In order to realize parametric simulation of three-dimensional(3D)fabric structure based on web,a 3D model describing a plain knitted fabric,in which the cross-section of the yarn is circular shape and the path of the yarn is cubic B-spline curve,is proposed in this paper.With this model,the 3D simulation of the loop and of the basic structures of the knitted fabric is realized by using Virtual Reality Modeling Language(VRML).The virtual simulation scene is suitable for network transmission with freely available VRML browsers and can be translated,scaled and rotated quite arbitrarily.By using Java and External Authoring Interface(EAI)technology,the web-based interactive simulation platform of weft knitted fabric is established.The user can input type of structures,basic fabric parameters,and yarn colors interactively to obtain a more realistic simulation result in real-time.A new approach is provided to imitate the knitted fabric 3D appearance on network.展开更多
The work investigated surface and mechanical properties of untreated and treated three-layered weftknitted spacer fabrics.In order to optimize the mechanical properties of weft-knitted spacer fabrics,silica aerogels(S...The work investigated surface and mechanical properties of untreated and treated three-layered weftknitted spacer fabrics.In order to optimize the mechanical properties of weft-knitted spacer fabrics,silica aerogels(SAs)coating was employed.Scanning electron microscopy(SEM)images of untreated and treated spacer fabrics were analyzed to ensure the presence of SAs on the coated spacer fabrics.The basic properties of uncoated and coated weftknitted spacer fabrics were studied and compared.Tensile strength and initial modulus were studied according to the GB/T3923 test standard YG026 MB-250 by testing machine.Moreover,compression properties of spacer fabrics were also tested by HD026 G test instrument.In this testing,work of compression,the linearity of compression,recovery work of compression and other parameters were calculated from stress and strain curves.It was found that SAs coating has a significant influence on the mechanical properties of weftknitted spacer fabrics.The statistical analysis also verified the significant performance(P value smaller than 0.05)of treated fabric samples at the 0.05 level.展开更多
Based on the theory of moisture vapor permeability and liquid moisture transmission through fabric, this paper is mainly concerned with the wet comfort of the fine denier polypropylene fiber knitted fabrics. The liqui...Based on the theory of moisture vapor permeability and liquid moisture transmission through fabric, this paper is mainly concerned with the wet comfort of the fine denier polypropylene fiber knitted fabrics. The liquid water transport property the liquid water retention property, the moisture permeability property, the moisture releasing and drying property of these fabrics are tested by normal objective ways and discussed. At last, according to these properties these fabries are classified by grey model synthetic evaluation method.展开更多
Water transport through the pore structure of the knitted fabric can occur only in place where the fiber-water surface attraction force is greater than the water weight in the capillary. To investigate wet permeabilit...Water transport through the pore structure of the knitted fabric can occur only in place where the fiber-water surface attraction force is greater than the water weight in the capillary. To investigate wet permeability of the knitted yarn in the fabric, a liquid transport model is established. The main factors which have significant influences on the liquid transport have been analyzed. It is derived from the argument that the optimal design for the knitted fabric with quick sweat transport property can be obtained.展开更多
This paper analyses the principle of wicking effect of the polypropylene filament yarn. By means of theoretical and experimental analysis, some factors affecting the moisture transmission of the pure polypropylene kni...This paper analyses the principle of wicking effect of the polypropylene filament yarn. By means of theoretical and experimental analysis, some factors affecting the moisture transmission of the pure polypropylene knitted fabrics are discussed.展开更多
文摘Stitch density is one of the critical quality parameters of knit fabrics. This parameter is closely related to other physical quality parameters like fabric weight, fabric tightness factor, fiber types, blend ratio, yarn diameter and linear density, and fabric structure. Selecting stitch density (wales per inch, course per inch) is essential to getting the appropriate fabric weight and desired quality. Usually, no rules or assumptions exist to get the desired stitch density in the finished fabric stage. Fifteen types of blended knit fabrics were prepared to conduct the study. The varying percentages of cotton, polyester, and elastane are incorporated in the blends. Regression analysis and regression ANOVA tests were done to predict the stitch density of finished fabrics. A suitable regression equation is established to get the desired results. The study also found that the stitch density value in the finished stage fabric decreases by approximately 15% compared to the stitch density in the grey fabric stage. This study will help the fabric manufacturers get the finished fabric stitch density in advance by utilizing the grey fabric stitch density data set. The author expects this research to benefit the knitting and dyeing industry, new researchers, and advanced researchers.
基金The project supported by the National Natural Science Foundation of China(10272079)
文摘The typical micro-knitting structure of knitted fabric,which makes it very different from woven fabric,is described.The tensile tests of knitted fabric are reported.The deformations of the micro-knitting structures are carefully studied.The study indicates that when a knitted fabric sheet is subjected to a tension along w-direction an extra compressive stress field inside loop in c-direction is induced.The extra stress field is also determined through analysis.Finally,a micro-mechanical model of knitted fabric is proposed.This work paves the way for the simulations of buckling modes of a knitted fabric sheet as are observed in experiments.
文摘Seven kinds of weft knitted fabrics from glass fiber yarns were used as reinforcement to make fabric/epoxy composite laminates. Tensile tests were carried out to examine and compare the mechanical properties in course and wale direction of these composites. On the basis of experimental results, attempts have been made to analyze some main factors influencing stress-strain curve, ultimate tensile strength and initial elastic modulus of specimens.
文摘A geometric model of relaxed plain-nitted fabric isproposed.A method based on the model for predictingthe loop length from the course spacing,wale spacing offabric and the diameter of yarn is deduced,as well as a computer program is developed to graphically represent the structures of plain knitted fabric with various struc-tural parameters.
文摘Wet permeability of fibrous assembly is mainly influenced by the properties of liquid and the configurations of the fiber which consist of diameter of fiber, twist angle and fiber alignment in a yarn. It can be seen from experimental results that the knitted fabric made of soybean (SB) fiber has goodproperties both in wet permeability and vapor transmission so that the knitting technology and fabric characteristics can be improved.
基金Technical Standards for the Development of Kinitted Jinlong Underw ear Factory of Guangdong Province,China(No.HX201303000008)
文摘Nowadays,more and more natural or functional fibers are being investigated due to their utilization in thermal underwear.Kapok fiber is one of the natural cellulosic fibers whose source is the kapok plant. It has hollow body and sealed tail,which exhibits desirable features required for functional textiles of this nature. In this study,cotton / kapok( 80 /20 by mass) blended yarn with two types of yarn size 18. 5 and 14. 8 tex,respectively are knitted into plain stitches. The fabrics are undergone with an optimal preparation plan according to orthogonal design. Then,after dyeing and softening,fabric properties including thermal and water-vapour resistances, wicking property, pilling behaviour, and surface morphology,are tested and scrutinized for their candidacy for thermal underwear. The results showed that cotton / kapok blended fabrics have good thermal resistance which is significantly higher than those of cotton / modal blended fabrics,and the same water vapour resistance compared with cotton / modal blended fabrics which are normally used as underwear. Cotton / modal blended knitted fabrics has better pilling grade than cotton / kapok blended fabrics. Meanwhile, the cotton / kapok blends fabrics have good wicking property. Collectively,it was concluded that cotton / kapok blended fabric was appropriate for thermal underwear. However,the main limitation of these fabrics is their pilling properties.
基金The project supported by the National Natural Science Foundation of China(10272079)
文摘With the aid of the micro-mechanical model of knitted fabric proposed in Part 1 we analyze the buckling of a knitted fabric sheet when it is subjected to a tension along the wale direction. The large deformation of the fabric sheet in the critical configuration is considered and, to avoid possible deviation due to the approximation of the theory of thin plate, the three-dimensional theory of instability is used. The fabric sheet is considered as a three-dimensional body and all boundary conditions are satisfied. It is shown that the buckling of the fabric sheet is possible, two buckling modes and the corresponding buckling conditions are obtained, but only the flexural mode is physically possible as observed in experiments.
基金Doctoral fundation of Tianjin Polytechnic University,China(No.029066)
文摘To improve design capabilities for the knitted fabric pattern,a preliminary study is carried out for the design method.Based on mathematical theory,pattern could be created automatically by computer with inputting different parameters for mathematical functions.The knitted fabric simulation is realized by M1 CAD pattern preparation system of STOLL Company.In the pattern,different color unit is replaced by obverse stitch with different color,or by obverse stitch and reverse stitch with the same color separately,after that the effects of knitted fabrics could be simulated.Designing with this method,it would not only help to acquire a great of diversity patterns,but also improve design efficiency and save cost.
文摘Warp knitting technology gets rapid development at present and becomes one of the most important parts of the textiles.But it is less known how the parameters of warp knitting technology affect the mechanical properties of warp-knitted fabrics.This paper presents discuss a research on the relationships between run-in ratio and mechanical properties of the two-bar warp-knittedfabrics through the measurement and analysis of the mechanical properties of various samples with different run-in ratios.The optimal run一in ratios for the reasonable mechanical properties are obtained from above dis-
文摘Several different kinds of weft knitted fabrics from glass fiber yarns were used as reinforcement to make fabric/polyester composite laminates. Flexural tests were carried out to examine stress- deflection process and compare the mechanical properties in course and wale directions of these composites. The experimental results indicate that the numbers of load-bearing yarn in course and wale direction and the fabric density are the main factors influencing the ultimate tensile strength and initial elastic modulus of specimens.
文摘Pilling is a severe concern for blended fabrics. The aesthetic look and smoothness are the buyers’ prime requirements. The main focus of the study was to see the pilling behavior from various percentages of polyester fiber blend ratio as well as the different pilling cycles on blended fabrics. The cotton, polyester, and elastane prepared the study fabrics. These fabrics are (90% Cotton/5% Polyester/5% Elastane, 90% Cotton/6% Polyester/4% Elastane, 90% Cotton/7% Polyester/3% Elastane, 90% Cotton/8% Polyester/2% Elastane, and 90% Cotton/9% Polyester/1% Elastane, 85% Cotton/10% Polyester/5% Elastane, 85% Cotton/11% Polyester/4% Elastane, 85% Cotton/12% Polyester/3% Elastane, 85% Cotton/13% Polyester/2% Elastane, and 85% Cotton/ 14% Polyester/1% Elastane, 80% Cotton/15% Polyester/5% Elastane, 80% Cotton/16% Polyester/4% Elastane, 80% Cotton/17% Polyester/3% Elastane, 80% Cotton/18% Polyester/2% Elastane, and 80% Cotton/19% Polyester/1% Elastane). The selected polyester blend ratios were 5%, 6%, 7%, 8%, 9%, 10%, 11%, 12%, 13%, 14%, 15%, 16%, 17%, 18% and 19% respectively. The study used the Martindale pilling tester with 2000, 5000, and 7000 cycles, respectively. The evaluation followed the ISO 12945-2:2000. The study findings are that the polyester fiber blend ratio did not influence the pilling grade on blended fabrics for pilling cycles 2000, and the pilling grade remained constant at 4 - 5. The pilling grade started to deteriorate in pilling cycle 5000 for the fabrics 85%C/10%P/5%E, 85%C/11%P/4%E, 85%C/12%P/3%E, 85%C/ 13%P/2%E, 85%C/14%P/1%E showed the pilling grade 4, and the fabrics made from 80%C/15%P/5%E, 80%C/16%P/4%E, 80%C/17%P/3%E, 80%C/ 18%P/2%E, 80%C/19%P/1%E showed the pilling grade 4, 3, 3, 3, and 3 respectively. For the pilling cycles 7000, the pilling grade further deteriorated for the fabrics 80%C/15%P/5%E, 80%C/16%P/4%E, 80%C/17%P/3%E, 80%C/ 18%P/2%E, 80%C/19%P/1%E showed the pilling grade 3, 3, 2, 2, and 2 respectively. The study finds the dominance of polyester fiber throughout the experiment. The author hopes this study’s outcome will help new researchers, advanced researchers, and the textile industry’s sustainable development research and development team.
文摘In this paper, dyeing processes of silk-like fabric of ultra-fine polyester fiber are studied through orthogonal experiment, dyeing properties (K/S value, L* value, and C* value) of the fabric are tested under different dyeing conditions (pH value, time, and bath ratlo), and optimum dyeing conditions are arrived at through analysis.
文摘This paper introduces the construction of the multi-layered biaxial weft knitted fabric （MBWK fabric） and studies the locking angle of this kind of fabric. Moreover, a locking angle model of the MBWK fabric is established for the first time according to its unique construction. Two kinds of locking angles are considered under different restraint conditions: the locking angle θ1 controlled by the inserting yarns and the locking angle θ2 controlled by the stitch yarns. It is concluded that the ultimate value of the locking angle θ is the larger one of the two angles.
文摘The outbreak of coronavirus has led to an increase in the demand for facemasks globally. Unavailability of appropriate polypropylene non-woven fabrics face masks as a result of inadequate supply to satisfy the growing population has brought about the manufacturing of locally fabrics masks to augment or substitute standard medical class facemasks. The study aims at analyzing airflow of these locally manufactured fabrics to determine possible means of transmitting the virus as well as establish comfort of the user of these masks. Standard polypropylene non-woven, woven and knitted fabrics were considered for the study. Air permeability test was conducted on these fabrics using Frazier Air permeability tester. Depending on the property significant variation in the textile fabrics, polypropylene non-woven is widely accepted for facial masks. Nevertheless, this study illustrates that woven and knitted fabrics have more open structures, which allow a high rate of air penetration and so may require two or three layers to prevent antimicrobial or antiviral potential.
基金Jiangsu Natural Science Foundation of University,China(No.07KJD540178)Foundation of Nantong Science and Technology of China(No.K2007009)Graduate Innovation Project of Nantong University,China(No.YKC09056)
文摘In order to realize parametric simulation of three-dimensional(3D)fabric structure based on web,a 3D model describing a plain knitted fabric,in which the cross-section of the yarn is circular shape and the path of the yarn is cubic B-spline curve,is proposed in this paper.With this model,the 3D simulation of the loop and of the basic structures of the knitted fabric is realized by using Virtual Reality Modeling Language(VRML).The virtual simulation scene is suitable for network transmission with freely available VRML browsers and can be translated,scaled and rotated quite arbitrarily.By using Java and External Authoring Interface(EAI)technology,the web-based interactive simulation platform of weft knitted fabric is established.The user can input type of structures,basic fabric parameters,and yarn colors interactively to obtain a more realistic simulation result in real-time.A new approach is provided to imitate the knitted fabric 3D appearance on network.
文摘The work investigated surface and mechanical properties of untreated and treated three-layered weftknitted spacer fabrics.In order to optimize the mechanical properties of weft-knitted spacer fabrics,silica aerogels(SAs)coating was employed.Scanning electron microscopy(SEM)images of untreated and treated spacer fabrics were analyzed to ensure the presence of SAs on the coated spacer fabrics.The basic properties of uncoated and coated weftknitted spacer fabrics were studied and compared.Tensile strength and initial modulus were studied according to the GB/T3923 test standard YG026 MB-250 by testing machine.Moreover,compression properties of spacer fabrics were also tested by HD026 G test instrument.In this testing,work of compression,the linearity of compression,recovery work of compression and other parameters were calculated from stress and strain curves.It was found that SAs coating has a significant influence on the mechanical properties of weftknitted spacer fabrics.The statistical analysis also verified the significant performance(P value smaller than 0.05)of treated fabric samples at the 0.05 level.
文摘Based on the theory of moisture vapor permeability and liquid moisture transmission through fabric, this paper is mainly concerned with the wet comfort of the fine denier polypropylene fiber knitted fabrics. The liquid water transport property the liquid water retention property, the moisture permeability property, the moisture releasing and drying property of these fabrics are tested by normal objective ways and discussed. At last, according to these properties these fabries are classified by grey model synthetic evaluation method.
文摘Water transport through the pore structure of the knitted fabric can occur only in place where the fiber-water surface attraction force is greater than the water weight in the capillary. To investigate wet permeability of the knitted yarn in the fabric, a liquid transport model is established. The main factors which have significant influences on the liquid transport have been analyzed. It is derived from the argument that the optimal design for the knitted fabric with quick sweat transport property can be obtained.
文摘This paper analyses the principle of wicking effect of the polypropylene filament yarn. By means of theoretical and experimental analysis, some factors affecting the moisture transmission of the pure polypropylene knitted fabrics are discussed.
