In sheet metal forming, drawbeads are often used to control uneven material flow which may cause defects such as wrinkles, fracture, surface distortion and springback. Appropriate setting and adjusting the drawbead fo...In sheet metal forming, drawbeads are often used to control uneven material flow which may cause defects such as wrinkles, fracture, surface distortion and springback. Appropriate setting and adjusting the drawbead force is one of the most important pa- rameters in sheet metal forming process control. This paper derives the model of loop drawbead restraining force (DBRF) using plastic forming theory, and gives the min imum blankholding force. Experiments are carried out to verify the proposed DBRF model. The good agreement between the calculated values and experiments data justi- fies the proposed loop drawbead restraining force model.展开更多
In order to research the plastic performance of sheet going through the drawbead and the simple tensile test of sheet, the influence of drawbead structure parameters on sheet performance and the subsequent performance...In order to research the plastic performance of sheet going through the drawbead and the simple tensile test of sheet, the influence of drawbead structure parameters on sheet performance and the subsequent performance of the sheet were performed to investigate the residual deformation characteristics of the sheet through different drawbead structures, and also the influences of drawbead structures and geometry parameters on pre-deformation and subsequent forming characters of sheet were analyzed. The results show that the pre-deformation decreases with the increase of the round corner radius, the pre-deformation increase with the increase of the height of drawbead, and the subsequent forming characteristics of sheet going through drawbead are remarkably different from undeformed sheet and these differences heavily depend on the pre-deformation. With the increases of pre-deformation, the yield ratio increases, but the subsequent elongation exponential decreases. These means deformability of the sheet is significantly reduced. As the structure of drawbead changes, the mechanical characteristics of material in different cyclic loading conditions also change. For the BUFDE+Z deep drawing steel sheet, the subsequent performance of the sheet is hardened when the pre-deformation is greater than 0.044. For the DC52D+ZF hot-galvanize steel sheet, the subsequent performance of the sheet begins to harden when the pre-deformation is greater than 0.079, and it presents that the pre-deformation is not bigger than 0.052.展开更多
With the drawing force acting on the blank across drawbeads numerically simulated by the elastico-plastic large deformation FEM, not only the distribution of drawing force in different areas of the blank as it passes ...With the drawing force acting on the blank across drawbeads numerically simulated by the elastico-plastic large deformation FEM, not only the distribution of drawing force in different areas of the blank as it passes through drawbeads during the deformation, but also the approximate drawbead resistance force and punch force can be seen so that drawbead resistance force and parameters of drawbeads can be separately studied.展开更多
Inner wrinkling phenomenon is more likely to develop during hydrodynamic deep drawing(HDD) of complicated component-forms due to the higher demand for controlling deformation sequences. Aiming at the problems in contr...Inner wrinkling phenomenon is more likely to develop during hydrodynamic deep drawing(HDD) of complicated component-forms due to the higher demand for controlling deformation sequences. Aiming at the problems in control of inner wrinkling for an irregular surface part featured with both concavity and convex, this research proposes an optimal design method of drawbead parameters to change the material flow. According to theoretical analysis of the mechanism of inner wrinkling, optimizing cavity pressure only is unreasonable to form a wrinkle-free deep-drawn part,so semi-circular drawbeads are employed. The effects of layout and height of drawbeads on forming results are discussed, and a process window is established based on evaluation indicators including the anti-wrinkle coefficient and the minimum wall thickness. Experiments are carried out to validate the process window, and the wall thickness and the wrinkle height are measured and compared with numerical findings. The results show that the anti-wrinkle ability of drawbeads weakens with increasing oblique angle and distance from the die center, while the wall thickness increases with increasing oblique angle and distance, and the inner wrinkling can be completely suppressed by drawbeads arranged in zones I and II with optimum penetration.展开更多
文摘In sheet metal forming, drawbeads are often used to control uneven material flow which may cause defects such as wrinkles, fracture, surface distortion and springback. Appropriate setting and adjusting the drawbead force is one of the most important pa- rameters in sheet metal forming process control. This paper derives the model of loop drawbead restraining force (DBRF) using plastic forming theory, and gives the min imum blankholding force. Experiments are carried out to verify the proposed DBRF model. The good agreement between the calculated values and experiments data justi- fies the proposed loop drawbead restraining force model.
基金Project(50305031) supported by the National Natural Science Foundation of ChinaProject(E2008000824) supported by Provincial Natural Science Foundation of Hebei
文摘In order to research the plastic performance of sheet going through the drawbead and the simple tensile test of sheet, the influence of drawbead structure parameters on sheet performance and the subsequent performance of the sheet were performed to investigate the residual deformation characteristics of the sheet through different drawbead structures, and also the influences of drawbead structures and geometry parameters on pre-deformation and subsequent forming characters of sheet were analyzed. The results show that the pre-deformation decreases with the increase of the round corner radius, the pre-deformation increase with the increase of the height of drawbead, and the subsequent forming characteristics of sheet going through drawbead are remarkably different from undeformed sheet and these differences heavily depend on the pre-deformation. With the increases of pre-deformation, the yield ratio increases, but the subsequent elongation exponential decreases. These means deformability of the sheet is significantly reduced. As the structure of drawbead changes, the mechanical characteristics of material in different cyclic loading conditions also change. For the BUFDE+Z deep drawing steel sheet, the subsequent performance of the sheet is hardened when the pre-deformation is greater than 0.044. For the DC52D+ZF hot-galvanize steel sheet, the subsequent performance of the sheet begins to harden when the pre-deformation is greater than 0.079, and it presents that the pre-deformation is not bigger than 0.052.
文摘With the drawing force acting on the blank across drawbeads numerically simulated by the elastico-plastic large deformation FEM, not only the distribution of drawing force in different areas of the blank as it passes through drawbeads during the deformation, but also the approximate drawbead resistance force and punch force can be seen so that drawbead resistance force and parameters of drawbeads can be separately studied.
基金supported by Chengdu Aircraft Industrial Corporation
文摘Inner wrinkling phenomenon is more likely to develop during hydrodynamic deep drawing(HDD) of complicated component-forms due to the higher demand for controlling deformation sequences. Aiming at the problems in control of inner wrinkling for an irregular surface part featured with both concavity and convex, this research proposes an optimal design method of drawbead parameters to change the material flow. According to theoretical analysis of the mechanism of inner wrinkling, optimizing cavity pressure only is unreasonable to form a wrinkle-free deep-drawn part,so semi-circular drawbeads are employed. The effects of layout and height of drawbeads on forming results are discussed, and a process window is established based on evaluation indicators including the anti-wrinkle coefficient and the minimum wall thickness. Experiments are carried out to validate the process window, and the wall thickness and the wrinkle height are measured and compared with numerical findings. The results show that the anti-wrinkle ability of drawbeads weakens with increasing oblique angle and distance from the die center, while the wall thickness increases with increasing oblique angle and distance, and the inner wrinkling can be completely suppressed by drawbeads arranged in zones I and II with optimum penetration.
