Titanium alloys are excellent structural materials in engineering fields,but their poor tribological properties limit their further applications.Electroless plating is an effective method to enhance the tribological p...Titanium alloys are excellent structural materials in engineering fields,but their poor tribological properties limit their further applications.Electroless plating is an effective method to enhance the tribological performance of alloys,but it is difficult to efficiently apply to titanium alloys,due to titanium alloy’s strong chemical activity.In this work,the electroless Nickel-Boron(Ni-B)coating was successfully deposited on the surface of titanium alloy(Ti-6AL-4V)via a new pre-treatment process.Then,linearly reciprocating sliding wear tests were performed to evaluate the tribological behaviors of titanium alloy and its electroless Ni-B coatings.It was found that the Ni-B coatings can decrease the wear rate of the titanium alloy from 19.89×10^(−3)mm^(3)to 0.41×10^(−3)mm^(3),which attributes to the much higher hardness of Ni-B coatings.After heat treatment,the hardness of Ni-B coating further increases corresponding to coating crystallization and hard phase formation.However,heat treatment does not improve the tribological performance of Ni-B coating,due to the fact that higher brittleness and more severe oxidative wear exacerbate the damage of heat-treated coatings.Furthermore,the Ni-B coatings heat-treated both in air and nitrogen almost present the same tribological performance.The finding of this work on electroless coating would further extend the practical applications of titanium alloys in the engineering fields.展开更多
A Ni–P alloy gradient coating consisting of multiple electroless Ni–P layers with various phosphorus contents was prepared on the aviation aluminum alloy. Several characterization and electrochemical techniques were...A Ni–P alloy gradient coating consisting of multiple electroless Ni–P layers with various phosphorus contents was prepared on the aviation aluminum alloy. Several characterization and electrochemical techniques were used to characterize the different Ni–P coatings’ morphologies, phase structures, elemental compositions, and corrosion protection. The gradient coating showed good adhesion and high corrosion and wear resistance, enabling the application of aluminum alloy in harsh environments. The results showed that the double zinc immersion was vital in obtaining excellent adhesion (81.2 N). The optimal coating was not peeled and shredded even after bending tests with angles higher than 90°and was not corroded visually after 500 h of neutral salt spray test at 35℃. The high corrosion resistance was attributed to the misaligning of these micro defects in the three different nickel alloy layers and the amorphous structure of the high P content in the outer layer. These findings guide the exploration of functional gradient coatings that meet the high application requirement of aluminum alloy parts in complicated and harsh aviation environments.展开更多
As a thin film solar cell absorber material, antimony selenide (Sb<sub>2</sub>Se<sub>3</sub>) has become a potential candidate recently because of its unique optical and electrical properties a...As a thin film solar cell absorber material, antimony selenide (Sb<sub>2</sub>Se<sub>3</sub>) has become a potential candidate recently because of its unique optical and electrical properties and easy fabrication method. X-ray photoelectron spectroscopy (XPS) was used to determine the stoichiometry and composition of electroless Sb<sub>2</sub>Se<sub>3</sub> thin films using depth profile studies. The surface layers were analyzed nearly stoichiometric. But the abundant amount of antimony makes the inner layer electrically more conductive.展开更多
Sb<sub>2</sub>S<sub>3</sub> has gained tremendous research recently for thin film solar cell absorber material because of their easy synthesis, unique electrical and optical properties. The sto...Sb<sub>2</sub>S<sub>3</sub> has gained tremendous research recently for thin film solar cell absorber material because of their easy synthesis, unique electrical and optical properties. The stoichiometry and composition of electroless Sb<sub>2</sub>S<sub>3</sub> thin films were analyzed using XPS depth profile studies. The surface layers were found nearly stoichiometric. On the other hand, the inner layer was rich in antimony composition making it more conductive electrically.展开更多
The rare earths of ytterbium, lanthanum, praseodymium, neodymium and their binary mixtures were respectively added into the traditional electroless plating solution to prepare thin palladium film on the inner surface ...The rare earths of ytterbium, lanthanum, praseodymium, neodymium and their binary mixtures were respectively added into the traditional electroless plating solution to prepare thin palladium film on the inner surface of porous ceramic tube. The experimental results shows that the addition of rare earths increases palladium deposition rates and the binary mixtures are superior to the single rare earths and the mixture of ytterbium-lanthanum is the most efficient. Adding the mixture of ytterbium-lanthanum can also reduce the plating temperature by 10～20 ℃, shrink the metal crystal size and improve the film densification compared to those by traditional electroless plating. A thin palladium film with 5 μm was prepared and the film made a highly pure hydrogen with a molar fraction of more than 99.97% from a H2-N2 gas mixture. More attentions were paid to analyze the physical and chemical behaviors of the rare earths in palladium film preparation.展开更多
Electroless NiP coating has stochastic nonlinear structure, which was in far from equilibrium and instability state. Fractal theory, an effective method for resolving nonlinear system, was introduced to describe the c...Electroless NiP coating has stochastic nonlinear structure, which was in far from equilibrium and instability state. Fractal theory, an effective method for resolving nonlinear system, was introduced to describe the coating structure quantitatively. Disorker and self-similarity characteristics, which are the two basic features of fractal, were explained in this paper for the first time. The results show that amorphous NiP structure exhibits scale invariance and can be quantitatively characterized by fractal dimension. Based on the fractal principle, a two-dimensional computer simulation on electroless NiP deposition was carried out and it is in agreement with the experimental result. Finally, the fractal dynamics and process of atom growth were investigated. The results show that the atom deposition is reaction-limited growth process.展开更多
In recent years,magnesium(Mg)has evolved as a salient material,in affiliation with electroless nickel(Ni)coating,which have found applications in automobiles,aerospace and confederate fields attributing to its excelle...In recent years,magnesium(Mg)has evolved as a salient material,in affiliation with electroless nickel(Ni)coating,which have found applications in automobiles,aerospace and confederate fields attributing to its excellent inherent weight sensitive properties.However,being acknowledged for its remarkable auxiliary properties like flexible machining,appreciable weight sensitivity and ability to be patently diecast into mesh constructs,magnesium is prejudiced by aeronautical standards predominantly for its inferior corrosion resistance properties.In this sense,electroless nickel plating on magnesium and its alloys has been suggested to extricate it from corrosion problem and make it more competitive in industrial and defence applications.Autocatalytic fixation of metal ions onto respective substrates accrues and alters their mechanical,electrochemical and tribological properties,destitute of any electric current aid.This proficiently identified technique is prosecuted with the assistance of a series of sequenced operations involving a prior pretreatment,which corresponds to the chemical cleaning of the substrate surface;electroless coating;and a later activation process which is a mild etching of the electroless coated surface.The susceptibility of magnesium to this methodology has advanced and propagated its exercise and applicability in aircraft,satellites and allied aeronautical fields.Contemporarily,researchers have proposed various eco-friendly and modified duplex and composite coatings which have transmuted properties of these appendages by tailoring alloy compositions and reagents employed.This review article systematically colligates various considerations and evaluations on electroless nickel applications of magnesium and its alloys and explicates how it anchors its practice in the respective domains.Furthermore,a comprehensive analysis is devised based on the pre-existing treatment methods for accomplishing the same.展开更多
In order to obtain substrates with good conductive foam for high porosity foam metal materials used in the metal electrodes,the technique of electroless copper plating on the microcellular polyurethane foam with pore ...In order to obtain substrates with good conductive foam for high porosity foam metal materials used in the metal electrodes,the technique of electroless copper plating on the microcellular polyurethane foam with pore size of 0.3 mm was investigated.The main factors affecting the deposition rate such as the solution composition,temperature,pH value and adding ultrasonic were explored.The results show that the optimum process conditions are CuSO4 16 g/L,HCHO 5 mL/L,NaKC4H4O6 30 g/L,Na2EDTA 20 g/L,K4Fe(CN)6 25 mg/L,pH value of 12.5-13.0 and temperature of 40-50℃.Under these technical conditions, the process has excellent bath stability.Adding ultrasonic on the process can elevate the deposition rate of copper by 20%-30%.The foam metal material with a porosity of 92.2%and a three-dimensional network structure,was fabricated by electro-deposition after the electroless copper plating.展开更多
Electroless nickel/immersion gold (ENIG) technology is widely used as one of the surface final finish for electronics packaging substrate and printed circuit board (PCB), providing a protective, conductive and soldera...Electroless nickel/immersion gold (ENIG) technology is widely used as one of the surface final finish for electronics packaging substrate and printed circuit board (PCB), providing a protective, conductive and solderable surface. However, there is a solder joint interfacial brittle fracture (or solderability failure) of using the ENIG coating. The characteristics and the application of ENIG technology were narrated in this paper. The research progress on the solderability failure of ENIG was introduced. The mechanism of "black pad" and the possible measure of eliminating or alleviating the "black pad" were also introduced. The development direction and market prospects of ENIG were prospected.展开更多
The binary mixture of Yb2O3-La2O3 was used as an additive to improve the traditional electroless plating for Pd-Ag co-deposition on the inside surface of a porous ceramic tube. The main attention were paid to investig...The binary mixture of Yb2O3-La2O3 was used as an additive to improve the traditional electroless plating for Pd-Ag co-deposition on the inside surface of a porous ceramic tube. The main attention were paid to investigating the effects of Yb2O3-La2O3 on Pd-Ag co-deposition rate, plating temperature, Ag content in film and Pd/Ag reduction potentials. The experimental results show that the co-deposition rate is increased by 63%, the plating temperature is decreased by 10～20 ℃ for obtaining the same co-deposition rate and the Ag content in film basically remains unchangeable when Yb2O3-La2O3 is added into the traditional electroless plating solution. The experiment also shows that Pd/Ag reduction potentials basically remain unchangeable with the binary rare earths based on the electrochemical mathematical models An inorganic composite membrane with alloy film of 76.8(mol)% Pd-23.2(mol)% Ag and the thickness of 7.7 μm on the porous ceramic tube was prepared and the permeation fluxes of hydrogen and nitrogen through the membrane are 8.65×10-3 and 1.92×10-6 m3·m-2·s-1 at 350 ℃ and 0.3 MPa respectively.展开更多
Manuscript received 24 June 1999 The Fe Al P alloy deposits were plated on copper sheets by electroless plating. The change law of the deposition rate, composition, surface appearance and structure for the deposits wa...Manuscript received 24 June 1999 The Fe Al P alloy deposits were plated on copper sheets by electroless plating. The change law of the deposition rate, composition, surface appearance and structure for the deposits was studied by changing the metallic salt ratios (AlCl 3/AlCl 3+FeSO 4), the concentration of metallic salt AlCl 3 and reductant NaH 2PO 2. The optimum plating bath was obtained. It was found that the choices of ligand and reductant were the key of increasing Al content for the deposits.展开更多
Bi2Te2.7Se0.3/Cu core/shell powders were prepared by electroless plating and hydrogen reduction, and then sintered into bulk by spark plasma sintering in order to improve the thermoelectric and mechanical properties o...Bi2Te2.7Se0.3/Cu core/shell powders were prepared by electroless plating and hydrogen reduction, and then sintered into bulk by spark plasma sintering in order to improve the thermoelectric and mechanical properties of n-type Bi-Te thermoelectric material. After electroless plating, with the increasing of Cu content, Seebeck coefficient keeps increasing and power factor enhances significantly. The highest power factor increases by three times and reaches 23.8 W·cm^-1·K^-2 at room temperature in Bi2Te2.7Se0.3 with 0.22 wt%Cu sample, which means electrical transport properties of Bi2Te2.7Se0.3/Cu samples have been improved.Meanwhile, the ZT values of Bi2Te2.7Se0.3/Cu samples can be enhanced at different temperature zone by adjusting the Cu content. Bi2Te2.7Se0.3 with 0.05 wt% Cu sample has the best thermoelectric properties in high temperature zone, and the ZT peak value increases from 0.35 to 0.85 at 623 K. When the Cu content increases to 0.15 wt%,the ZT peak value moves to the low temperature(373 K) and increases from 0.24 to 0.71. At the same time, the mechanical properties increases with the increasing of Cu content.展开更多
The electrochemical method was used to remove nickel ion from spent electroless nickel plating bath (pH=5 3). An electrolytic cell was composed of a porous nickel foam cathode and an inert RuO 2/Ti anode. Nickel ions ...The electrochemical method was used to remove nickel ion from spent electroless nickel plating bath (pH=5 3). An electrolytic cell was composed of a porous nickel foam cathode and an inert RuO 2/Ti anode. Nickel ions were reduced and deposited on the surface of the nickel foam cathode. The effect of current density (i), linear velocity of wastewater(v), gap between cathode and anode(d C/A) and reaction time(t) on nickel removal rate and current efficiency were studied. As reaction time prolonged, nickel removal rate increased while current efficiency decreased. And larger v and smaller d C/A can enhance nickel removal rate and increase current efficiency by promoting mass transfer and dropping concentration polarization. The effect of current density on nickel removal by electrochemistry was related to other parameters. After three hours’ electrolysis with i=1 0 A/dm2, v=18 5 cm/min and d C/A=0 5 cm, nickel removal rate and current efficiency reached 85 6% and 29 1%, respectively.展开更多
Al-based MIL-53 MOF nanostructure was synthesized hydrothermally and then co-deposited in the electroless nickel coating on AM60B magnesium alloy using Zr pretreatment as an eco-friendly underlayer.The MIL-53(Al)nanos...Al-based MIL-53 MOF nanostructure was synthesized hydrothermally and then co-deposited in the electroless nickel coating on AM60B magnesium alloy using Zr pretreatment as an eco-friendly underlayer.The MIL-53(Al)nanostructure was synthesized in the form of layered semi-cube crystals with the surface area and mean pore diameter of 985.72 m^(2)g^(-1) and 2.00 nm,respectively.The SEM images captured with two various zooming scales from the surface of the plain and MOF containing electroless layers showed cauliflower-like morphology with even distribution of nodule size.Also,the sub-grains of the plain coating disappeared after incorporation of the MOF.Although,both the normal and nanostructure-containing electroless layers have crystalline-amorphous structure,but the nanocomposite coating showed less crystallinity.The average surface roughness of the plain electroless coating was about 309 nm,which decreased to about 222 nm after incorporation of the MOF.The XRD patterns showed that the characteristic peak of Ni broadened after incorporation of the MOF,probably due to the decreasing of the crystallinity.For the heat-treated normal and MOF containing coatings at 200℃ no phase transition takes place,but new peaks appeared for heat-treated coatings at 400℃ due to the crystallization and second-phase precipitation.The results of the EIS tests showed an increase in the amount of the charge transfer resistance(from 19 to 29 kΩcm^(2))after addition of the MOF,which means an improvement in the corrosion resistance.Also,low Jcorrof the composite coating represents its higher corrosion resistance with respect to the plain coating.The micro-hardness values of the composite coating before and after the heat treatment were higher than the plain coating.Also,the Ni-P-MOF coating has a lower wear rate both before and after the heat treatment due to an improvement in its micro-hardness.展开更多
By plasma transmitting spectrograph,electron energy spectrometry,X-ray diffractometry,transmission electron microscopy and micro-hardometry,the effects of ultrasonic irradiation and rare earth metal cerium on the depo...By plasma transmitting spectrograph,electron energy spectrometry,X-ray diffractometry,transmission electron microscopy and micro-hardometry,the effects of ultrasonic irradiation and rare earth metal cerium on the depositing speed,chemical composition,crystal structure and microhardness of electroless Co-Ni-B alloy coating were inspected and analyzed. The results show that cerium and ultrasonic irradiation can evidently raise the depositing speed of electroless Co-Ni-B alloy. The cerium content of electroless Co-Ni-B-Ce alloy coating also increases after ultrasonic irradiation applied to electroless Co-Ni-B plating process. Under the action of ultrasonic irradiation and rare metal cerium,the chemical composition of electroless Co-Ni-B alloy coating is changed. Electroless Co-Ni-B alloy with amorphous structure is transformed to electroless Co-Ni-B-Ce alloy with microcrystalline in general state and electroless Co-Ni-B-Ce alloy with crystalline structure in ultrasonic irradiation. In this way microhardness of the coatings increases remarkably.展开更多
This research aims to use several kind of rare earth oxides, such as Nd2O3, Yb2O3, Ce2O3 and La2O3, to improve the electroless plating and electroplating processes for surface metallization of quartz optical fiber (si...This research aims to use several kind of rare earth oxides, such as Nd2O3, Yb2O3, Ce2O3 and La2O3, to improve the electroless plating and electroplating processes for surface metallization of quartz optical fiber (silicon fiber) for its practical uses. The effects of the rare earth oxides on the deposition rate of Ni-P-B, the stability of the plating solution and the surface property of the film were investigated and the comparisons of their behaviours were made. The effects of rare earth oxide of La2O3 on the hardness and surface property of the Ni film prepared by electroplating process were studied. The surface morphonogies, compositions and hardness of the Ni-P-B and Ni films were characterized and analyzed by SEM, MSM, ICP and DIMHM, respectively. The experimental results showed that Ce2O3 with the concentration of 4 mg·L-1 was the best one among the four rare earth oxides with suitable concentrations in increasing the deposition rate, enhancing the stability of the electroless plating solution and improving the surface property of the Ni-P-B film. The improvements of the hardness and surface property of the Ni film prepared by electroplating with adding La2O3 were discovered. No obvious influences of Ce2O3 and La2O3 on the compositions of Ni-P-B and Ce free in the Ni-P-B film were found because of its much more nagative deposition potential than those of the used reducing agents in this experiment. The total diameter of the quartz optical fiber with deposited Ni-P-B film and Ni film was about 1.7 mm, which could be satisfactorily for the practical uses of quartz optical fiber in many fields.展开更多
A new type elctroless plating bath for solar control glass with large area uniform plating was presented on the basis of the relative Reynolds numbers , the temperature distribution calculation and the relative struct...A new type elctroless plating bath for solar control glass with large area uniform plating was presented on the basis of the relative Reynolds numbers , the temperature distribution calculation and the relative structure design. The experimental data of the distribution and change of temperature indicate that the mass transfer of the fluid was steady laminar flow and the difference of the maximum temperature was less than 0 5℃ in glass dipping region of 1000×200×1000mm.展开更多
The effects of rare earth element cerium on composition and electrochemical characteristics of electroless Co-Ni-B alloy were studied in this paper. The alloy component was analyzed using Inductively Coupled Plasma (I...The effects of rare earth element cerium on composition and electrochemical characteristics of electroless Co-Ni-B alloy were studied in this paper. The alloy component was analyzed using Inductively Coupled Plasma (ICP). The plating rate is was determined by electronic balance. The cathode polarization curves and cyclic voltammogram during the electroless deposition were tested by LK998Ⅱmodel electrochemical analytical system. The results show that rare earth element Ce can co-deposit with cobalt-based alloy, and with mass increase of Ce added in aqueous solution, the contents of Co, Ni, Ce in alloy increase and the content of B decreases. Ce can increase deposition rate of alloy in some range. The rare earth makes deposition potential move to positive direction and makes polarizability decrease.展开更多
基金Supported by Sichuan Provincial Science and Technology Program of China(Grant No.2018JY0245)National Natural Science Foundation of China(Grant No.51975492)Natural Science Foundation of Southwest University of Science and Technology of China(Grant No.19xz7163).
文摘Titanium alloys are excellent structural materials in engineering fields,but their poor tribological properties limit their further applications.Electroless plating is an effective method to enhance the tribological performance of alloys,but it is difficult to efficiently apply to titanium alloys,due to titanium alloy’s strong chemical activity.In this work,the electroless Nickel-Boron(Ni-B)coating was successfully deposited on the surface of titanium alloy(Ti-6AL-4V)via a new pre-treatment process.Then,linearly reciprocating sliding wear tests were performed to evaluate the tribological behaviors of titanium alloy and its electroless Ni-B coatings.It was found that the Ni-B coatings can decrease the wear rate of the titanium alloy from 19.89×10^(−3)mm^(3)to 0.41×10^(−3)mm^(3),which attributes to the much higher hardness of Ni-B coatings.After heat treatment,the hardness of Ni-B coating further increases corresponding to coating crystallization and hard phase formation.However,heat treatment does not improve the tribological performance of Ni-B coating,due to the fact that higher brittleness and more severe oxidative wear exacerbate the damage of heat-treated coatings.Furthermore,the Ni-B coatings heat-treated both in air and nitrogen almost present the same tribological performance.The finding of this work on electroless coating would further extend the practical applications of titanium alloys in the engineering fields.
基金financially supported by the National Natural Science Foundation of China (No.52271073)。
文摘A Ni–P alloy gradient coating consisting of multiple electroless Ni–P layers with various phosphorus contents was prepared on the aviation aluminum alloy. Several characterization and electrochemical techniques were used to characterize the different Ni–P coatings’ morphologies, phase structures, elemental compositions, and corrosion protection. The gradient coating showed good adhesion and high corrosion and wear resistance, enabling the application of aluminum alloy in harsh environments. The results showed that the double zinc immersion was vital in obtaining excellent adhesion (81.2 N). The optimal coating was not peeled and shredded even after bending tests with angles higher than 90°and was not corroded visually after 500 h of neutral salt spray test at 35℃. The high corrosion resistance was attributed to the misaligning of these micro defects in the three different nickel alloy layers and the amorphous structure of the high P content in the outer layer. These findings guide the exploration of functional gradient coatings that meet the high application requirement of aluminum alloy parts in complicated and harsh aviation environments.
文摘As a thin film solar cell absorber material, antimony selenide (Sb<sub>2</sub>Se<sub>3</sub>) has become a potential candidate recently because of its unique optical and electrical properties and easy fabrication method. X-ray photoelectron spectroscopy (XPS) was used to determine the stoichiometry and composition of electroless Sb<sub>2</sub>Se<sub>3</sub> thin films using depth profile studies. The surface layers were analyzed nearly stoichiometric. But the abundant amount of antimony makes the inner layer electrically more conductive.
文摘Sb<sub>2</sub>S<sub>3</sub> has gained tremendous research recently for thin film solar cell absorber material because of their easy synthesis, unique electrical and optical properties. The stoichiometry and composition of electroless Sb<sub>2</sub>S<sub>3</sub> thin films were analyzed using XPS depth profile studies. The surface layers were found nearly stoichiometric. On the other hand, the inner layer was rich in antimony composition making it more conductive electrically.
基金Project supported by Science and Technology Committee of Jiangxi Province
文摘The rare earths of ytterbium, lanthanum, praseodymium, neodymium and their binary mixtures were respectively added into the traditional electroless plating solution to prepare thin palladium film on the inner surface of porous ceramic tube. The experimental results shows that the addition of rare earths increases palladium deposition rates and the binary mixtures are superior to the single rare earths and the mixture of ytterbium-lanthanum is the most efficient. Adding the mixture of ytterbium-lanthanum can also reduce the plating temperature by 10～20 ℃, shrink the metal crystal size and improve the film densification compared to those by traditional electroless plating. A thin palladium film with 5 μm was prepared and the film made a highly pure hydrogen with a molar fraction of more than 99.97% from a H2-N2 gas mixture. More attentions were paid to analyze the physical and chemical behaviors of the rare earths in palladium film preparation.
文摘Electroless NiP coating has stochastic nonlinear structure, which was in far from equilibrium and instability state. Fractal theory, an effective method for resolving nonlinear system, was introduced to describe the coating structure quantitatively. Disorker and self-similarity characteristics, which are the two basic features of fractal, were explained in this paper for the first time. The results show that amorphous NiP structure exhibits scale invariance and can be quantitatively characterized by fractal dimension. Based on the fractal principle, a two-dimensional computer simulation on electroless NiP deposition was carried out and it is in agreement with the experimental result. Finally, the fractal dynamics and process of atom growth were investigated. The results show that the atom deposition is reaction-limited growth process.
文摘In recent years,magnesium(Mg)has evolved as a salient material,in affiliation with electroless nickel(Ni)coating,which have found applications in automobiles,aerospace and confederate fields attributing to its excellent inherent weight sensitive properties.However,being acknowledged for its remarkable auxiliary properties like flexible machining,appreciable weight sensitivity and ability to be patently diecast into mesh constructs,magnesium is prejudiced by aeronautical standards predominantly for its inferior corrosion resistance properties.In this sense,electroless nickel plating on magnesium and its alloys has been suggested to extricate it from corrosion problem and make it more competitive in industrial and defence applications.Autocatalytic fixation of metal ions onto respective substrates accrues and alters their mechanical,electrochemical and tribological properties,destitute of any electric current aid.This proficiently identified technique is prosecuted with the assistance of a series of sequenced operations involving a prior pretreatment,which corresponds to the chemical cleaning of the substrate surface;electroless coating;and a later activation process which is a mild etching of the electroless coated surface.The susceptibility of magnesium to this methodology has advanced and propagated its exercise and applicability in aircraft,satellites and allied aeronautical fields.Contemporarily,researchers have proposed various eco-friendly and modified duplex and composite coatings which have transmuted properties of these appendages by tailoring alloy compositions and reagents employed.This review article systematically colligates various considerations and evaluations on electroless nickel applications of magnesium and its alloys and explicates how it anchors its practice in the respective domains.Furthermore,a comprehensive analysis is devised based on the pre-existing treatment methods for accomplishing the same.
文摘In order to obtain substrates with good conductive foam for high porosity foam metal materials used in the metal electrodes,the technique of electroless copper plating on the microcellular polyurethane foam with pore size of 0.3 mm was investigated.The main factors affecting the deposition rate such as the solution composition,temperature,pH value and adding ultrasonic were explored.The results show that the optimum process conditions are CuSO4 16 g/L,HCHO 5 mL/L,NaKC4H4O6 30 g/L,Na2EDTA 20 g/L,K4Fe(CN)6 25 mg/L,pH value of 12.5-13.0 and temperature of 40-50℃.Under these technical conditions, the process has excellent bath stability.Adding ultrasonic on the process can elevate the deposition rate of copper by 20%-30%.The foam metal material with a porosity of 92.2%and a three-dimensional network structure,was fabricated by electro-deposition after the electroless copper plating.
基金Project supported by the Specialized Research Fund for the Doctoral Programof Higher Education (20030213007)the Heilongjiang Province Natural Science Foundation (E0325)
文摘Electroless nickel/immersion gold (ENIG) technology is widely used as one of the surface final finish for electronics packaging substrate and printed circuit board (PCB), providing a protective, conductive and solderable surface. However, there is a solder joint interfacial brittle fracture (or solderability failure) of using the ENIG coating. The characteristics and the application of ENIG technology were narrated in this paper. The research progress on the solderability failure of ENIG was introduced. The mechanism of "black pad" and the possible measure of eliminating or alleviating the "black pad" were also introduced. The development direction and market prospects of ENIG were prospected.
基金Project supported by Science and Technology Committee of Jiangxi Province
文摘The binary mixture of Yb2O3-La2O3 was used as an additive to improve the traditional electroless plating for Pd-Ag co-deposition on the inside surface of a porous ceramic tube. The main attention were paid to investigating the effects of Yb2O3-La2O3 on Pd-Ag co-deposition rate, plating temperature, Ag content in film and Pd/Ag reduction potentials. The experimental results show that the co-deposition rate is increased by 63%, the plating temperature is decreased by 10～20 ℃ for obtaining the same co-deposition rate and the Ag content in film basically remains unchangeable when Yb2O3-La2O3 is added into the traditional electroless plating solution. The experiment also shows that Pd/Ag reduction potentials basically remain unchangeable with the binary rare earths based on the electrochemical mathematical models An inorganic composite membrane with alloy film of 76.8(mol)% Pd-23.2(mol)% Ag and the thickness of 7.7 μm on the porous ceramic tube was prepared and the permeation fluxes of hydrogen and nitrogen through the membrane are 8.65×10-3 and 1.92×10-6 m3·m-2·s-1 at 350 ℃ and 0.3 MPa respectively.
文摘Manuscript received 24 June 1999 The Fe Al P alloy deposits were plated on copper sheets by electroless plating. The change law of the deposition rate, composition, surface appearance and structure for the deposits was studied by changing the metallic salt ratios (AlCl 3/AlCl 3+FeSO 4), the concentration of metallic salt AlCl 3 and reductant NaH 2PO 2. The optimum plating bath was obtained. It was found that the choices of ligand and reductant were the key of increasing Al content for the deposits.
基金Funded by the National Natural Science Foundation of China(No.51371073)
文摘Bi2Te2.7Se0.3/Cu core/shell powders were prepared by electroless plating and hydrogen reduction, and then sintered into bulk by spark plasma sintering in order to improve the thermoelectric and mechanical properties of n-type Bi-Te thermoelectric material. After electroless plating, with the increasing of Cu content, Seebeck coefficient keeps increasing and power factor enhances significantly. The highest power factor increases by three times and reaches 23.8 W·cm^-1·K^-2 at room temperature in Bi2Te2.7Se0.3 with 0.22 wt%Cu sample, which means electrical transport properties of Bi2Te2.7Se0.3/Cu samples have been improved.Meanwhile, the ZT values of Bi2Te2.7Se0.3/Cu samples can be enhanced at different temperature zone by adjusting the Cu content. Bi2Te2.7Se0.3 with 0.05 wt% Cu sample has the best thermoelectric properties in high temperature zone, and the ZT peak value increases from 0.35 to 0.85 at 623 K. When the Cu content increases to 0.15 wt%,the ZT peak value moves to the low temperature(373 K) and increases from 0.24 to 0.71. At the same time, the mechanical properties increases with the increasing of Cu content.
文摘The electrochemical method was used to remove nickel ion from spent electroless nickel plating bath (pH=5 3). An electrolytic cell was composed of a porous nickel foam cathode and an inert RuO 2/Ti anode. Nickel ions were reduced and deposited on the surface of the nickel foam cathode. The effect of current density (i), linear velocity of wastewater(v), gap between cathode and anode(d C/A) and reaction time(t) on nickel removal rate and current efficiency were studied. As reaction time prolonged, nickel removal rate increased while current efficiency decreased. And larger v and smaller d C/A can enhance nickel removal rate and increase current efficiency by promoting mass transfer and dropping concentration polarization. The effect of current density on nickel removal by electrochemistry was related to other parameters. After three hours’ electrolysis with i=1 0 A/dm2, v=18 5 cm/min and d C/A=0 5 cm, nickel removal rate and current efficiency reached 85 6% and 29 1%, respectively.
基金the Iran National Science Foundation(INSF)and University of Mohaghegh Ardabil for financial support of this study。
文摘Al-based MIL-53 MOF nanostructure was synthesized hydrothermally and then co-deposited in the electroless nickel coating on AM60B magnesium alloy using Zr pretreatment as an eco-friendly underlayer.The MIL-53(Al)nanostructure was synthesized in the form of layered semi-cube crystals with the surface area and mean pore diameter of 985.72 m^(2)g^(-1) and 2.00 nm,respectively.The SEM images captured with two various zooming scales from the surface of the plain and MOF containing electroless layers showed cauliflower-like morphology with even distribution of nodule size.Also,the sub-grains of the plain coating disappeared after incorporation of the MOF.Although,both the normal and nanostructure-containing electroless layers have crystalline-amorphous structure,but the nanocomposite coating showed less crystallinity.The average surface roughness of the plain electroless coating was about 309 nm,which decreased to about 222 nm after incorporation of the MOF.The XRD patterns showed that the characteristic peak of Ni broadened after incorporation of the MOF,probably due to the decreasing of the crystallinity.For the heat-treated normal and MOF containing coatings at 200℃ no phase transition takes place,but new peaks appeared for heat-treated coatings at 400℃ due to the crystallization and second-phase precipitation.The results of the EIS tests showed an increase in the amount of the charge transfer resistance(from 19 to 29 kΩcm^(2))after addition of the MOF,which means an improvement in the corrosion resistance.Also,low Jcorrof the composite coating represents its higher corrosion resistance with respect to the plain coating.The micro-hardness values of the composite coating before and after the heat treatment were higher than the plain coating.Also,the Ni-P-MOF coating has a lower wear rate both before and after the heat treatment due to an improvement in its micro-hardness.
文摘By plasma transmitting spectrograph,electron energy spectrometry,X-ray diffractometry,transmission electron microscopy and micro-hardometry,the effects of ultrasonic irradiation and rare earth metal cerium on the depositing speed,chemical composition,crystal structure and microhardness of electroless Co-Ni-B alloy coating were inspected and analyzed. The results show that cerium and ultrasonic irradiation can evidently raise the depositing speed of electroless Co-Ni-B alloy. The cerium content of electroless Co-Ni-B-Ce alloy coating also increases after ultrasonic irradiation applied to electroless Co-Ni-B plating process. Under the action of ultrasonic irradiation and rare metal cerium,the chemical composition of electroless Co-Ni-B alloy coating is changed. Electroless Co-Ni-B alloy with amorphous structure is transformed to electroless Co-Ni-B-Ce alloy with microcrystalline in general state and electroless Co-Ni-B-Ce alloy with crystalline structure in ultrasonic irradiation. In this way microhardness of the coatings increases remarkably.
基金the State Special Programs for 973 Key Foundamental Pre-Research (2005cca04300)
文摘This research aims to use several kind of rare earth oxides, such as Nd2O3, Yb2O3, Ce2O3 and La2O3, to improve the electroless plating and electroplating processes for surface metallization of quartz optical fiber (silicon fiber) for its practical uses. The effects of the rare earth oxides on the deposition rate of Ni-P-B, the stability of the plating solution and the surface property of the film were investigated and the comparisons of their behaviours were made. The effects of rare earth oxide of La2O3 on the hardness and surface property of the Ni film prepared by electroplating process were studied. The surface morphonogies, compositions and hardness of the Ni-P-B and Ni films were characterized and analyzed by SEM, MSM, ICP and DIMHM, respectively. The experimental results showed that Ce2O3 with the concentration of 4 mg·L-1 was the best one among the four rare earth oxides with suitable concentrations in increasing the deposition rate, enhancing the stability of the electroless plating solution and improving the surface property of the Ni-P-B film. The improvements of the hardness and surface property of the Ni film prepared by electroplating with adding La2O3 were discovered. No obvious influences of Ce2O3 and La2O3 on the compositions of Ni-P-B and Ce free in the Ni-P-B film were found because of its much more nagative deposition potential than those of the used reducing agents in this experiment. The total diameter of the quartz optical fiber with deposited Ni-P-B film and Ni film was about 1.7 mm, which could be satisfactorily for the practical uses of quartz optical fiber in many fields.
文摘A new type elctroless plating bath for solar control glass with large area uniform plating was presented on the basis of the relative Reynolds numbers , the temperature distribution calculation and the relative structure design. The experimental data of the distribution and change of temperature indicate that the mass transfer of the fluid was steady laminar flow and the difference of the maximum temperature was less than 0 5℃ in glass dipping region of 1000×200×1000mm.
基金Project supported by the National Natural Science Fund Aiding Object of China (50371023)
文摘The effects of rare earth element cerium on composition and electrochemical characteristics of electroless Co-Ni-B alloy were studied in this paper. The alloy component was analyzed using Inductively Coupled Plasma (ICP). The plating rate is was determined by electronic balance. The cathode polarization curves and cyclic voltammogram during the electroless deposition were tested by LK998Ⅱmodel electrochemical analytical system. The results show that rare earth element Ce can co-deposit with cobalt-based alloy, and with mass increase of Ce added in aqueous solution, the contents of Co, Ni, Ce in alloy increase and the content of B decreases. Ce can increase deposition rate of alloy in some range. The rare earth makes deposition potential move to positive direction and makes polarizability decrease.
