Recently,exploration breakthroughs have been made in the Lower Cretaceous sandstone reservoirs in the Doseo Basin,but the identification of reservoir fluid property is difficult due to variable reservoir lithology,com...Recently,exploration breakthroughs have been made in the Lower Cretaceous sandstone reservoirs in the Doseo Basin,but the identification of reservoir fluid property is difficult due to variable reservoir lithology,complex oil-water contact within and faint responses of the oil zone,which causes the lower accuracy of reservoir fluid property identification with conventional mudlogging and wirelogging techniques.Applying the geochemical logging,fluorescent logging,mud logging and cutting logging technology,in combination with formation test data,this paper distinguishes the crude oil types,analyzes the logging response characteristics of oil zone after water washing,and establishes the interpretation charts and parameter standards for reservoir fluid properties.The crude oil can be divided into two types,namely viscous-heavy and thin-light,based on total hydrocarbon content and component concentration tested by mud logging,features of pyrolysis gas chromatogram and fluorescence spectroscopy.The general characteristics of oil layers experienced water washing include the decrease of total hydrocarbon content and component concentration from mud logging,the decrease of S1 and PS values from geochemical logging,the decrease of hydrocarbon abundance and absence of some light components in pyrolysis gas chromatogram,and the decrease of fluorescence area and intensity from fluorescence logging.According to crude oil types,the cross plots of S1 versus peak-baseline ratio,and the cross plots of rock wettability versus fluorescence area ratio are drawn and used to interpret reservoir fluid property.Meanwhile,the standards of reservoir fluid parameter are established combining with the parameters of PS and the parameters in above charts,and comprehensive multiparameter correlation in both vertical and horizontal ways is also performed to interpret reservoir fluid property.The application in the Doseo Basin achieved great success,improving interpretation ability of fluid property in the reservoir with complex oil-water contact,and also provided technical reference for the efficient exploration and development of similar reservoirs.展开更多
The Ordovician Majiagou Formation is one of the main gas-producing strata in the Ordos Basin,China.The identification of hydrocarbon-bearing intervals via conventional well logs is a challenging task.This study descri...The Ordovician Majiagou Formation is one of the main gas-producing strata in the Ordos Basin,China.The identification of hydrocarbon-bearing intervals via conventional well logs is a challenging task.This study describes the litholog of Ma 5(Member 5 of Majiagou Formation)dolostones,and then analyzes the responses of various conventional well logs to the presences of natural gas.The lithology of the gas bearing layers is dominantly of the dolomicrite to fine to medium crystalline dolomite.Natural gas can be produced from the low resistivity layers,and the dry layers are characterized by high resistivities.Neutron-density crossovers are not sensitive to the presences of natural gas.In addition,there are no significant increases in sonic transit times in natural gas bearing layers.NMR(nuclear magnetic resonance)logs,DSI(Dipole Sonic Imager)logs and borehole image logs(XRMI)are introduced to discriminate the fluid property in Majiagou dolostone reservoirs.The gas bearing intervals have broad NMR T2(transverse relaxation time)spectrum with tail distributions as well as large T2gm(T2 logarithmic mean values)values,and the T2 spectrum commonly display polymodal behaviors.In contrast,the dry layers and water layers have low T2gm values and very narrow T2 spectrum without tails.The gas bearing layers are characterized by low Vp/Vs ratios,low Poisson’s ratios and low P-wave impedances,therefore the fluid property can be discriminated using DSI logs,and the interpretation results show good matches with the gas test data.The apparent formation water resistivity(AFWR)spectrum can be derived from XRMI image logs by using the Archie’s formula in the flushed zone.The gas bearing layers have broad apparent formation water resistivity spectrum and tail distributions compared with the dry and water layers,and also the interpretation results from the image logs exhibit good agreement with the gas test data.The fluid property in Majiagou dolostone reservoirs can be discriminated through NMR logs,DSI logs and borehole image logs.This study helps establish a predictable model for fluid property in dolostones,and have implications in dolostone reservoirs with similar geological backgrounds worldwide.展开更多
Hydrotalcite can act as a co-stabilizer with other main stabilizer for poly(vinyl chloride)(PVC). The thermal stability and fluid property of PVC filled with hydrotalcite surface-treated with titanate and silane were ...Hydrotalcite can act as a co-stabilizer with other main stabilizer for poly(vinyl chloride)(PVC). The thermal stability and fluid property of PVC filled with hydrotalcite surface-treated with titanate and silane were studied in this work. Organic Sn is a main stabilizer and hydrotalcite is a stabilizing assistant. The stability of the PVC resin mixed with organic Sn and hydrotalcite is better than that of the PVC resin mixed with organic Sn alone. It is shown that the PVC resin filled with hydrotalcite possesses a better static and dynamic heat stability. Moreover, hydrotalcite can improve the fluid property of PVC, which is advantageous to the processing of PVC, and the optimum content of hydrotalcite is about 1%-2%(mass fraction).展开更多
Cone-disk systems find frequent use such as conical diffusers,medical devices,various rheometric,and viscosimetry applications.In this study,we investigate the three-dimensional flow of a water-based Ag-Mg O hybrid na...Cone-disk systems find frequent use such as conical diffusers,medical devices,various rheometric,and viscosimetry applications.In this study,we investigate the three-dimensional flow of a water-based Ag-Mg O hybrid nanofluid in a static cone-disk system while considering temperature-dependent fluid properties.How the variable fluid properties affect the dynamics and heat transfer features is studied by Reynolds's linearized model for variable viscosity and Chiam's model for variable thermal conductivity.The single-phase nanofluid model is utilized to describe convective heat transfer in hybrid nanofluids,incorporating the experimental data.This model is developed as a coupled system of convective-diffusion equations,encompassing the conservation of momentum and the conservation of thermal energy,in conjunction with an incompressibility condition.A self-similar model is developed by the Lie-group scaling transformations,and the subsequent self-similar equations are then solved numerically.The influence of variable fluid parameters on both swirling and non-swirling flow cases is analyzed.Additionally,the Nusselt number for the disk surface is calculated.It is found that an increase in the temperature-dependent viscosity parameter enhances heat transfer characteristics in the static cone-disk system,while the thermal conductivity parameter has the opposite effect.展开更多
The existing acoustic logging methods for evaluating the hydraulic fracturing effectiveness usually use the fracture density to evaluate the fracture volume, and the results often cannot accurately reflect the actual ...The existing acoustic logging methods for evaluating the hydraulic fracturing effectiveness usually use the fracture density to evaluate the fracture volume, and the results often cannot accurately reflect the actual productivity. This paper studies the dynamic fluid flow through hydraulic fractures and its effect on borehole acoustic waves. Firstly, based on the fractal characteristics of fractures observed in hydraulic fracturing experiments, a permeability model of complex fracture network is established. Combining the dynamic fluid flow response of the model with the Biot-Rosenbaum theory that describes the acoustic wave propagation in permeable formations, the influence of hydraulic fractures on the velocity dispersion of borehole Stoneley-wave is then calculated and analyzed, whereby a novel hydraulic fracture fluid transport property evaluation method is proposed. The results show that the Stoneley-wave velocity dispersion characteristics caused by complex fractures can be equivalent to those of the plane fracture model, provided that the average permeability of the complex fracture model is equal to the permeability of the plane fracture. In addition, for fractures under high-permeability(fracture width 10~100 μm, permeability ~100 μm^(2)) and reduced permeability(1~10 μm, ~10 μm^(2), as in fracture closure) conditions, the Stoneley-wave velocity dispersion characteristics are significantly different. The field application shows that this fluid transport property evaluation method is practical to assess the permeability and the connectivity of hydraulic fractures.展开更多
The study involved the evaluation of the hydrocarbon potential of FORMAT Field, coastal swamp depobelt Niger delta, Nigeria to obtain a more efficient reservoir characterization and fluid properties identification. De...The study involved the evaluation of the hydrocarbon potential of FORMAT Field, coastal swamp depobelt Niger delta, Nigeria to obtain a more efficient reservoir characterization and fluid properties identification. Despite advances in seismic data interpretation using traditional 3D seismic data interpretation, obtaining adequate reservoir characteristics at the finest level had proved very challenging with often disappointing results. A method that integrates the amplitude variation with offfset (AVO) analysis is hereby proposed to better illuminate the reservoir. The Hampson Russell 10.3 was used to integrate and study the available seismic and well data. The reservoir of interest was delineated using the available suite of petrophysical data. This was marked by low gamma ray, high resistivity, and low acoustic impedance between a true subsea vertical depth (TVDss) range of 10,350 - 10,450 ft. The AVO fluid substitution yielded a decrease in the density values of pure gas (2.3 - 1.6 g/cc), pure oil (2.3 - 1.8 g/cc) while the Poisson pure brine increased (2.3 to 2.8 g/cc). Result from FORMAT 26 plots yielded a negative intercept and negative gradient at the top and a positive intercept and positive gradient at the Base which conforms to Class III AVO anomaly. FORMAT 30 plots yielded a negative intercept and positive gradient at the top and a positive intercept and negative gradient at the Base which conforms to class IV AVO anomaly. AVO attribute volume slices decreased in the Poisson ratio (0.96 to - 1.0) indicating that the reservoir contains hydrocarbon. The s-wave reflectivity and the product of the intercept and gradient further clarified that there was a Class 3 gas sand in the reservoir and the possibility of a Class 4 gas sand anomaly in that same reservoir.展开更多
The effects of variable fluid properties and variable heat flux on the flow and heat transfer of a non-Newtonian Maxwell fluid over an unsteady stretching sheet in the presence of slip velocity have been studied. The ...The effects of variable fluid properties and variable heat flux on the flow and heat transfer of a non-Newtonian Maxwell fluid over an unsteady stretching sheet in the presence of slip velocity have been studied. The governing differential equations are transformed into a set of coupled non-linear ordinary differential equations and then solved with a numerical technique using appropriate boundary conditions for various physical parameters. The numerical solution for the governing non-linear boundary value problem is based on applying the fourth-order Runge-Kutta method coupled with the shooting technique over the entire range of physical parameters. The effects of various parameters like the viscosity parameter, thermal conductivity parameter, unsteadiness parameter, slip velocity parameter, the Deborah number, and the Prandtl number on the flow and temperature profiles as well as on the local skin-friction coefficient and the local Nusselt number are presented and discussed. Comparison of numerical results is made with the earlier published results under limiting cases.展开更多
This study examines theoretically and computationally the non-Newtonian boundary layer flow and heat transfer for a viscoelastic fluid over a stretching continuous sheet embedded in a porous medium with variable fluid...This study examines theoretically and computationally the non-Newtonian boundary layer flow and heat transfer for a viscoelastic fluid over a stretching continuous sheet embedded in a porous medium with variable fluid properties, slip velocity, and internal heat generation/absorption. The flow in boundary layer is considered to be generated solely by the stretching of the sheet adjacent to porous medium with boundary wall slip condition. Highly nonlinear momentum and thermal boundary layer equations governing the flow and heat transfer are reduced to set of nonlinear ordinary differential equations by appropriate transformation. The resulting ODEs are successfully solved numerically with the help of shooting method. Graphical results are shown for non-dimensional velocities and temperature. The effects of heat generation/absorption parameter, the porous parameter, the viscoelastic parameter, velocity slip parameter, variable thermal conductivity and the Prandtl number on the flow and temperature profiles are presented. Moreover, the local skin-friction coefficient and Nusselt number are presented. Comparison of numerical results is made with the earlier published results under limiting cases.展开更多
Slurry reactors are popular in many industrial processes,involved with numerous chemical and biological mixtures,solid particles with different concentrations and properties,and a wide range of operating conditions.Th...Slurry reactors are popular in many industrial processes,involved with numerous chemical and biological mixtures,solid particles with different concentrations and properties,and a wide range of operating conditions.These factors can significantly affect the hydrodynamic in the slurry reactors,having remarkable effects on the design,scale-up,and operation of the slurry reactors.This article reviews the influences of fluid physical properties,solid particles,and operating conditions on the hydrodynamics in slurry reactors.Firstly,the influence of fluid properties,including the density and viscosity of the individual liquid and gas phases and the interfacial tension,has been reviewed.Secondly,the solid particle properties(i.e.,concentration,density,size,wettability,and shape)on the hydrodynamics have been discussed in detail,and some vital but often ignored features,especially the influences of particle wettability and shape,as well as the variation of surface tension because of solid concentration alteration,are highlighted in this work.Thirdly,the variations of physical properties of fluids,hydrodynamics,and bubble behavior resulted from the temperature and pressure variations are also summarized,and the indirect influences of pressure on viscosity and surface tension are addressed systematically.Finally,conclusions and perspectives of these notable influences on the design and scale-up of industrial slurry reactors are presented.展开更多
This work deals with the influence of thermal radiation on the problem of the mixed convection thin film flow and heat transfer of a micropolar fluid past a moving infinite vertical porous flat plate with a slip veloc...This work deals with the influence of thermal radiation on the problem of the mixed convection thin film flow and heat transfer of a micropolar fluid past a moving infinite vertical porous flat plate with a slip velocity. The fluid viscosity and the thermal conductivity are assumed to be the functions of temperature. The equations governing the flow are solved numerically by the Chebyshev spectral method for some representative value of various parameters. In comparison with the previously published work, the excellent agreement is shown. The effects of various parameters on the velocity, the microrotation velocity, and the temperature profiles, as well as the skin-friction coefficient and the Nusselt number, are plotted and discussed.展开更多
Present drilling fluids for deep water wells have severe degenerative effect on the environment with high operational and disposal costs.Thus,making them less desirable in recent times.Ester synthetic drilling fluid p...Present drilling fluids for deep water wells have severe degenerative effect on the environment with high operational and disposal costs.Thus,making them less desirable in recent times.Ester synthetic drilling fluid provides a novel environmentally friendly alternative but conventional ester-based drilling fluids exhibit high viscosities in deep-water wells causing excessive equivalent circulating density(ECD)and increased risk of lost circulation owing to narrow mud density window.This study experimentally investigates the critical fluid properties and aerobic biodegradability potentials of two newly developed deep-water synthetic ester drilling fluids namely:iso-propyl caprylate(COIPE)and iso-propyl linolenate(LOIPE)synthetic fluids and their comparison with synthetic-paraffin(SP-SBF)and isomerized-olefin(IOSBF)synthetic hydrocarbon fluids.The esters of iso-propyl caprylate and iso-propyl linolenate were produced from the isolation of ester mixtures that were obtained from the homogeneous catalytic transesterification of coconut and linseed plant oil biomass respectively.The COIPE was isolated from the coconut oil iso-propyl ester mixture by low-pressure fractional distillation technique.While fractional distillation and crystallization were used to isolate the LOIPE ester from the linseed oil iso-propyl ester mixture.Meanwhile,the aerobic biodegradation investigation was conducted by a modified oxygen consumption respirometry technique.The GC-MS analysis of the COIPE and LOIPE showed that the former contains essentially of lower saturated carbon compounds(C8).Whereas the latter contains higher molecular weight and unsaturated carbon compounds(C18+).The COIPE and LOIPE kinematic viscosity values are in good agreement with that of the reference synthetic hydrocarbon fluid samples(SP-SBF and IO-SBF).Although,the COIPE synthetic ester has lower viscosity value owing to the presence of shorter chain and saturated carbon atoms(C8 esters).Similarly,the linolenic oil iso-propyl ester has excellent cold flow characteristics for deep-water well drilling owing to lower values of cloud and pour points as a result of higher concentration of poly-unsaturated linolenic esters.The iso-propyl caprylate and the iso-propyl linolenate ester synthetic fluids are readily biodegradable in the sea water inoculum under aerobic condition.However,the iso-propyl caprylate is inherently biodegradable because its degradation level and that of the reference chemical sample were already above 60%during the 10-day window period.The SP-SBF and the IO-SBF synthetic fluids have lower aerobic biodegradation values because they contain little quantity of poly aromatic hydrocarbons as evident in their GC-MS profiles.Finally,esters and unsaturated synthetic-based fluid are more rapidly biodegradable than paraffinic synthetic fluids and the rate of biodegradation of organic compounds decreases as molecular weight increases.展开更多
Recently,nanoparticles have proven to enhance oil recovery on the core-flood scale in challenging high-pressure high-temperature reservoirs.Nanomaterials generally appear to improve oil production through wettability ...Recently,nanoparticles have proven to enhance oil recovery on the core-flood scale in challenging high-pressure high-temperature reservoirs.Nanomaterials generally appear to improve oil production through wettability alteration and reduction in interfacial tension between oil and water phases.Besides,they are environmentally friendly and cost-effective enhanced oil recovery techniques.Studying the rheological properties of nanoparticles is critical for field applications.The instability of nanoparticle dispersion due to aggregation is considered as an unfavorable phenomenon in nanofluid flooding while conducting an EOR process.In this study,wettability behavior and rheological properties of surface-treated silica nanoparticles using internal olefins sulfonates(IOS20–24 and IOS19–23),anionic surfactants were investigated.Surface modification effect on the stability of the colloidal solution in porous media and oil recovery was inspected.The rheology of pure and surfacetreated silica nanoparticles was investigated using a HPHT rheometer.Morphology and particle size distributions of pure and coated silica nanoparticles were studied using a field emission scanning electron microscope.A series of core-flood runs was conducted to evaluate the oil recovery factor.The coated silica nanoparticles were found to alter rheological properties and exhibited a shear-thinning behavior as the stability of the coated silica nanoparticles could be improved considerably.At low shear rates,the viscosity slightly increases,and the opposite happens at higher shear rates.Furthermore,the surfacemodified silica nanoparticles were found to alter the wettability of the aqueous phase into strongly water-wet by changing the contact angle from 80°to 3°measured against glass slides representing sandstone rocks.Oil–water IFT results showed that the surface treatment by surfactant lowered the oil–water IFT by 30%.Also,the viscosity of brine increased from 0.001 to 0.008 Pa s by introducing SiO2 nanoparticles to the aqueous phase for better displacement efficiency during chemicalassisted EOR.The core-flood experiments revealed that the ultimate oil recovery is increased by approximately 13%with a surfactant-coated silica nanofluid flood after the conventional waterflooding that proves the potential of smart nanofluids for enhancing oil recovery.The experimental results imply that the use of surfactant-coated nanoparticles in tertiary oil recovery could facilitate the displacement efficiency,alter the wettability toward more water-wet and avoid viscous fingering for stable flood front and additional oil recovery.展开更多
With special drilling operation equipment and specific conditions of geology, how does drilling fluid carry cuttings effectively? So far, it is still an urgent problem for drilling researchers to study. This work just...With special drilling operation equipment and specific conditions of geology, how does drilling fluid carry cuttings effectively? So far, it is still an urgent problem for drilling researchers to study. This work just aims at the actual engineering background to develop studying model. In this paper, according to non Newtonian fluid mechanics, the law of the solid liquid, two phase fluid flow and actual drilling engineering, the major factors affecting cuttings transport are drilling fluid velocity, hole inclination and fluid rheological properties. Getting a clear understanding of the law of drilling fluid and its cutting taking mechanism, this paper puts forward a model for analysis of field data and quantitative forecast of cutting taking capability of drilling fluid. The full scale annular test section was 6.1 m with 76 and 114 mm drillpipe in a 203 mm ID (wellbore diameter). Hole angle varied from 0° to 90°.展开更多
A set of experimental data obtained at the Institute of Physics and Power Engineering in a vertical bundle cooled with supercritical R-12 was analyzed. The test section was a 7-element bundle installed in a hexagonal ...A set of experimental data obtained at the Institute of Physics and Power Engineering in a vertical bundle cooled with supercritical R-12 was analyzed. The test section was a 7-element bundle installed in a hexagonal flow channel with three grid spacers. Data was collected at pressures of approximately 4.65 MPa for several different combinations of wall and bulk-fluid temperatures that were below, at, or above pseudocritical conditions. Analysis of the data has confirmed that there are three distinct heat-transfer regimes for forced convention in supercritical fluids： （1） normal heat transfer, （2） deteriorated heat transfer, and （3） enhanced heat transfer. It was also confirmed that the effects of spacers are evident which was previously observed in sub-critical experimental data. This work compares the wall and bulk fluid temperature data of the experiments to predictions based upon current 1-D correlations for heat transfer in supercritical fluids.展开更多
The development of shale reservoirs has brought a paradigm shift in the worldwide energy equation.This entails developing robust techniques to properly evaluate and unlock the potential of those reservoirs.The applica...The development of shale reservoirs has brought a paradigm shift in the worldwide energy equation.This entails developing robust techniques to properly evaluate and unlock the potential of those reservoirs.The application of Nuclear Magnetic Resonance techniques in fluid typing and properties estimation is well-developed in conventional reservoirs.However,Shale reservoirs characteristics like pore size,organic matter,clay content,wettability,adsorption,and mineralogy would limit the applicability of the used interpretation methods and correlation.Some of these limitations include the inapplicability of the controlling equations that were derived assuming fast relaxation regime,the overlap of different fluids peaks and the lack of robust correlation to estimate fluid properties in shale.This study presents a state-of-the-art review of the main contributions presented on fluid typing methods and correlations in both experimental and theoretical side.The study involves Dual Tw,Dual Te,and doping agent's application,T1-T2,D-T2 and T2sec vs.T1/T2 methods.In addition,fluid properties estimation such as density,viscosity and the gas-oil ratio is discussed.This study investigates the applicability of these methods along with a study of the current fluid properties correlations and their limitations.Moreover,it recommends the appropriate method and correlation which are capable of tackling shale heterogeneity.展开更多
We investigate, in this paper, the effects of thermo-physical properties on the flow and heat transfer in a thin film of a power-law liquid over a horizontal stretching surface in the presence of a viscous dissipation...We investigate, in this paper, the effects of thermo-physical properties on the flow and heat transfer in a thin film of a power-law liquid over a horizontal stretching surface in the presence of a viscous dissipation. The fluid properties, namely the fluid viscosity and the fluid thermal conductivity, are assumed to vary with temperature. Using a similarity transformation, the governing partial differential equations with a time dependent boundary are converted into coupled non-linear Ordinary Differential Equations （ODEs） with variable coefficients. Numerical solutions of the coupled ODEs are obtained by a finite difference scheme known as the Keller-box method. Results for the velocity and temperature distributions are presented graphically for different values of the pertinent parameters. The effects of unsteady parameter on the skin friction, the wall temperature gradient and the film thickness are presented and analyzed for zero and non-zero values of the temperature-dependent thermo-physical properties. The results obtained reveal many interesting features that warrant further study on the non-Newtonian thin film fluid flow phenomena, especially the shear-thinning phenomena.展开更多
A generalized geoacoustic model of fluid mud layer in Chanaiiang Estuary and Hangzhou Bay has been derived from a large amount of in-situ measurements of bulk density (p) profiles of the lay6rs and of lab measurements...A generalized geoacoustic model of fluid mud layer in Chanaiiang Estuary and Hangzhou Bay has been derived from a large amount of in-situ measurements of bulk density (p) profiles of the lay6rs and of lab measurements of acoustic velocities (c) and attenuation coefficients (o) of the fluid mud samples with different values of p for four frequencies of 100 kHz, 150 kHz, 500 kHz, 1500 kHz. The main features of the geoacoustic model can be expressed as follows: from the upper boundary, the bulk density of the fiuid mud increases linearly with depth z, however there is a gradient change (knee) when p is about 12.5 kN/m', then p increases linearly to a value about 15.0 kN/m'. After p more than 15.0, the fluid mud layer quickly transform into an ooze layer. In the fluid mud layer, the acoustic velocity c can be regarded as constant since its variation with z less than 1.5%, and a minimum vaue of c ekists when p is about 13.5 kN/m'. The variations of β with p and with frequency f are linear. Based on the geo-acoustic model and the ray theory, simulations of sound refiection from the fluid mud layers have been made, and some significallt results obtained, from which the bulk density profiles of fluld mud layers can be derived inversely.展开更多
基金funded by a project entitled exploration field evaluation and target optimization of key basins in Chad and Niger(No.2019D-4308)initiated by the scientific research and technology development project of china national petroleum corporation.
文摘Recently,exploration breakthroughs have been made in the Lower Cretaceous sandstone reservoirs in the Doseo Basin,but the identification of reservoir fluid property is difficult due to variable reservoir lithology,complex oil-water contact within and faint responses of the oil zone,which causes the lower accuracy of reservoir fluid property identification with conventional mudlogging and wirelogging techniques.Applying the geochemical logging,fluorescent logging,mud logging and cutting logging technology,in combination with formation test data,this paper distinguishes the crude oil types,analyzes the logging response characteristics of oil zone after water washing,and establishes the interpretation charts and parameter standards for reservoir fluid properties.The crude oil can be divided into two types,namely viscous-heavy and thin-light,based on total hydrocarbon content and component concentration tested by mud logging,features of pyrolysis gas chromatogram and fluorescence spectroscopy.The general characteristics of oil layers experienced water washing include the decrease of total hydrocarbon content and component concentration from mud logging,the decrease of S1 and PS values from geochemical logging,the decrease of hydrocarbon abundance and absence of some light components in pyrolysis gas chromatogram,and the decrease of fluorescence area and intensity from fluorescence logging.According to crude oil types,the cross plots of S1 versus peak-baseline ratio,and the cross plots of rock wettability versus fluorescence area ratio are drawn and used to interpret reservoir fluid property.Meanwhile,the standards of reservoir fluid parameter are established combining with the parameters of PS and the parameters in above charts,and comprehensive multiparameter correlation in both vertical and horizontal ways is also performed to interpret reservoir fluid property.The application in the Doseo Basin achieved great success,improving interpretation ability of fluid property in the reservoir with complex oil-water contact,and also provided technical reference for the efficient exploration and development of similar reservoirs.
基金This work is financially supported by the Science Foundation of China University of Petroleum, Beijing (Grant No. 2462017YJRC023)the Fundamental Research Funds for the Central Universities and the Opening Fund of Key Laboratory of Deep Oil & Gas (Grant No. 20CX02116A)
文摘The Ordovician Majiagou Formation is one of the main gas-producing strata in the Ordos Basin,China.The identification of hydrocarbon-bearing intervals via conventional well logs is a challenging task.This study describes the litholog of Ma 5(Member 5 of Majiagou Formation)dolostones,and then analyzes the responses of various conventional well logs to the presences of natural gas.The lithology of the gas bearing layers is dominantly of the dolomicrite to fine to medium crystalline dolomite.Natural gas can be produced from the low resistivity layers,and the dry layers are characterized by high resistivities.Neutron-density crossovers are not sensitive to the presences of natural gas.In addition,there are no significant increases in sonic transit times in natural gas bearing layers.NMR(nuclear magnetic resonance)logs,DSI(Dipole Sonic Imager)logs and borehole image logs(XRMI)are introduced to discriminate the fluid property in Majiagou dolostone reservoirs.The gas bearing intervals have broad NMR T2(transverse relaxation time)spectrum with tail distributions as well as large T2gm(T2 logarithmic mean values)values,and the T2 spectrum commonly display polymodal behaviors.In contrast,the dry layers and water layers have low T2gm values and very narrow T2 spectrum without tails.The gas bearing layers are characterized by low Vp/Vs ratios,low Poisson’s ratios and low P-wave impedances,therefore the fluid property can be discriminated using DSI logs,and the interpretation results show good matches with the gas test data.The apparent formation water resistivity(AFWR)spectrum can be derived from XRMI image logs by using the Archie’s formula in the flushed zone.The gas bearing layers have broad apparent formation water resistivity spectrum and tail distributions compared with the dry and water layers,and also the interpretation results from the image logs exhibit good agreement with the gas test data.The fluid property in Majiagou dolostone reservoirs can be discriminated through NMR logs,DSI logs and borehole image logs.This study helps establish a predictable model for fluid property in dolostones,and have implications in dolostone reservoirs with similar geological backgrounds worldwide.
文摘Hydrotalcite can act as a co-stabilizer with other main stabilizer for poly(vinyl chloride)(PVC). The thermal stability and fluid property of PVC filled with hydrotalcite surface-treated with titanate and silane were studied in this work. Organic Sn is a main stabilizer and hydrotalcite is a stabilizing assistant. The stability of the PVC resin mixed with organic Sn and hydrotalcite is better than that of the PVC resin mixed with organic Sn alone. It is shown that the PVC resin filled with hydrotalcite possesses a better static and dynamic heat stability. Moreover, hydrotalcite can improve the fluid property of PVC, which is advantageous to the processing of PVC, and the optimum content of hydrotalcite is about 1%-2%(mass fraction).
文摘Cone-disk systems find frequent use such as conical diffusers,medical devices,various rheometric,and viscosimetry applications.In this study,we investigate the three-dimensional flow of a water-based Ag-Mg O hybrid nanofluid in a static cone-disk system while considering temperature-dependent fluid properties.How the variable fluid properties affect the dynamics and heat transfer features is studied by Reynolds's linearized model for variable viscosity and Chiam's model for variable thermal conductivity.The single-phase nanofluid model is utilized to describe convective heat transfer in hybrid nanofluids,incorporating the experimental data.This model is developed as a coupled system of convective-diffusion equations,encompassing the conservation of momentum and the conservation of thermal energy,in conjunction with an incompressibility condition.A self-similar model is developed by the Lie-group scaling transformations,and the subsequent self-similar equations are then solved numerically.The influence of variable fluid parameters on both swirling and non-swirling flow cases is analyzed.Additionally,the Nusselt number for the disk surface is calculated.It is found that an increase in the temperature-dependent viscosity parameter enhances heat transfer characteristics in the static cone-disk system,while the thermal conductivity parameter has the opposite effect.
基金Supported by the National Natural Science Foundation of China (41821002,42174145)PetroChina Science and Technology Major Project (ZD2019-183-004)China University of Petroleum (East China) Graduate Student Innovation Project (YCX2019001)。
文摘The existing acoustic logging methods for evaluating the hydraulic fracturing effectiveness usually use the fracture density to evaluate the fracture volume, and the results often cannot accurately reflect the actual productivity. This paper studies the dynamic fluid flow through hydraulic fractures and its effect on borehole acoustic waves. Firstly, based on the fractal characteristics of fractures observed in hydraulic fracturing experiments, a permeability model of complex fracture network is established. Combining the dynamic fluid flow response of the model with the Biot-Rosenbaum theory that describes the acoustic wave propagation in permeable formations, the influence of hydraulic fractures on the velocity dispersion of borehole Stoneley-wave is then calculated and analyzed, whereby a novel hydraulic fracture fluid transport property evaluation method is proposed. The results show that the Stoneley-wave velocity dispersion characteristics caused by complex fractures can be equivalent to those of the plane fracture model, provided that the average permeability of the complex fracture model is equal to the permeability of the plane fracture. In addition, for fractures under high-permeability(fracture width 10~100 μm, permeability ~100 μm^(2)) and reduced permeability(1~10 μm, ~10 μm^(2), as in fracture closure) conditions, the Stoneley-wave velocity dispersion characteristics are significantly different. The field application shows that this fluid transport property evaluation method is practical to assess the permeability and the connectivity of hydraulic fractures.
文摘The study involved the evaluation of the hydrocarbon potential of FORMAT Field, coastal swamp depobelt Niger delta, Nigeria to obtain a more efficient reservoir characterization and fluid properties identification. Despite advances in seismic data interpretation using traditional 3D seismic data interpretation, obtaining adequate reservoir characteristics at the finest level had proved very challenging with often disappointing results. A method that integrates the amplitude variation with offfset (AVO) analysis is hereby proposed to better illuminate the reservoir. The Hampson Russell 10.3 was used to integrate and study the available seismic and well data. The reservoir of interest was delineated using the available suite of petrophysical data. This was marked by low gamma ray, high resistivity, and low acoustic impedance between a true subsea vertical depth (TVDss) range of 10,350 - 10,450 ft. The AVO fluid substitution yielded a decrease in the density values of pure gas (2.3 - 1.6 g/cc), pure oil (2.3 - 1.8 g/cc) while the Poisson pure brine increased (2.3 to 2.8 g/cc). Result from FORMAT 26 plots yielded a negative intercept and negative gradient at the top and a positive intercept and positive gradient at the Base which conforms to Class III AVO anomaly. FORMAT 30 plots yielded a negative intercept and positive gradient at the top and a positive intercept and negative gradient at the Base which conforms to class IV AVO anomaly. AVO attribute volume slices decreased in the Poisson ratio (0.96 to - 1.0) indicating that the reservoir contains hydrocarbon. The s-wave reflectivity and the product of the intercept and gradient further clarified that there was a Class 3 gas sand in the reservoir and the possibility of a Class 4 gas sand anomaly in that same reservoir.
文摘The effects of variable fluid properties and variable heat flux on the flow and heat transfer of a non-Newtonian Maxwell fluid over an unsteady stretching sheet in the presence of slip velocity have been studied. The governing differential equations are transformed into a set of coupled non-linear ordinary differential equations and then solved with a numerical technique using appropriate boundary conditions for various physical parameters. The numerical solution for the governing non-linear boundary value problem is based on applying the fourth-order Runge-Kutta method coupled with the shooting technique over the entire range of physical parameters. The effects of various parameters like the viscosity parameter, thermal conductivity parameter, unsteadiness parameter, slip velocity parameter, the Deborah number, and the Prandtl number on the flow and temperature profiles as well as on the local skin-friction coefficient and the local Nusselt number are presented and discussed. Comparison of numerical results is made with the earlier published results under limiting cases.
文摘This study examines theoretically and computationally the non-Newtonian boundary layer flow and heat transfer for a viscoelastic fluid over a stretching continuous sheet embedded in a porous medium with variable fluid properties, slip velocity, and internal heat generation/absorption. The flow in boundary layer is considered to be generated solely by the stretching of the sheet adjacent to porous medium with boundary wall slip condition. Highly nonlinear momentum and thermal boundary layer equations governing the flow and heat transfer are reduced to set of nonlinear ordinary differential equations by appropriate transformation. The resulting ODEs are successfully solved numerically with the help of shooting method. Graphical results are shown for non-dimensional velocities and temperature. The effects of heat generation/absorption parameter, the porous parameter, the viscoelastic parameter, velocity slip parameter, variable thermal conductivity and the Prandtl number on the flow and temperature profiles are presented. Moreover, the local skin-friction coefficient and Nusselt number are presented. Comparison of numerical results is made with the earlier published results under limiting cases.
基金supported by the National Natural Science Foundation of China(2187831821808234)+5 种基金the Dalian National Laboratory for Clean Energy Cooperation Fund,CAS(DNL201902)“Transformational Technologies for Clean Energy and Demonstration”,Strategic Priority Research Program of the Chinese Academy of Sciences(CAS)(XDA21060400)Qingdao Institute of Bioenergy and Bioprocess Technology(QIBEBT)and Dalian National Laboratory for Clean Energy(DNL)of CAS(QIBEBT ZZBS201803QIBEBT I201907)Director Innovation Fund of Synthetic Biology Technology Innovation Center of Shandong Province(sdsynbio-2020-ZH02)Project of CNPC-DICP Joint Research Center。
文摘Slurry reactors are popular in many industrial processes,involved with numerous chemical and biological mixtures,solid particles with different concentrations and properties,and a wide range of operating conditions.These factors can significantly affect the hydrodynamic in the slurry reactors,having remarkable effects on the design,scale-up,and operation of the slurry reactors.This article reviews the influences of fluid physical properties,solid particles,and operating conditions on the hydrodynamics in slurry reactors.Firstly,the influence of fluid properties,including the density and viscosity of the individual liquid and gas phases and the interfacial tension,has been reviewed.Secondly,the solid particle properties(i.e.,concentration,density,size,wettability,and shape)on the hydrodynamics have been discussed in detail,and some vital but often ignored features,especially the influences of particle wettability and shape,as well as the variation of surface tension because of solid concentration alteration,are highlighted in this work.Thirdly,the variations of physical properties of fluids,hydrodynamics,and bubble behavior resulted from the temperature and pressure variations are also summarized,and the indirect influences of pressure on viscosity and surface tension are addressed systematically.Finally,conclusions and perspectives of these notable influences on the design and scale-up of industrial slurry reactors are presented.
文摘This work deals with the influence of thermal radiation on the problem of the mixed convection thin film flow and heat transfer of a micropolar fluid past a moving infinite vertical porous flat plate with a slip velocity. The fluid viscosity and the thermal conductivity are assumed to be the functions of temperature. The equations governing the flow are solved numerically by the Chebyshev spectral method for some representative value of various parameters. In comparison with the previously published work, the excellent agreement is shown. The effects of various parameters on the velocity, the microrotation velocity, and the temperature profiles, as well as the skin-friction coefficient and the Nusselt number, are plotted and discussed.
文摘Present drilling fluids for deep water wells have severe degenerative effect on the environment with high operational and disposal costs.Thus,making them less desirable in recent times.Ester synthetic drilling fluid provides a novel environmentally friendly alternative but conventional ester-based drilling fluids exhibit high viscosities in deep-water wells causing excessive equivalent circulating density(ECD)and increased risk of lost circulation owing to narrow mud density window.This study experimentally investigates the critical fluid properties and aerobic biodegradability potentials of two newly developed deep-water synthetic ester drilling fluids namely:iso-propyl caprylate(COIPE)and iso-propyl linolenate(LOIPE)synthetic fluids and their comparison with synthetic-paraffin(SP-SBF)and isomerized-olefin(IOSBF)synthetic hydrocarbon fluids.The esters of iso-propyl caprylate and iso-propyl linolenate were produced from the isolation of ester mixtures that were obtained from the homogeneous catalytic transesterification of coconut and linseed plant oil biomass respectively.The COIPE was isolated from the coconut oil iso-propyl ester mixture by low-pressure fractional distillation technique.While fractional distillation and crystallization were used to isolate the LOIPE ester from the linseed oil iso-propyl ester mixture.Meanwhile,the aerobic biodegradation investigation was conducted by a modified oxygen consumption respirometry technique.The GC-MS analysis of the COIPE and LOIPE showed that the former contains essentially of lower saturated carbon compounds(C8).Whereas the latter contains higher molecular weight and unsaturated carbon compounds(C18+).The COIPE and LOIPE kinematic viscosity values are in good agreement with that of the reference synthetic hydrocarbon fluid samples(SP-SBF and IO-SBF).Although,the COIPE synthetic ester has lower viscosity value owing to the presence of shorter chain and saturated carbon atoms(C8 esters).Similarly,the linolenic oil iso-propyl ester has excellent cold flow characteristics for deep-water well drilling owing to lower values of cloud and pour points as a result of higher concentration of poly-unsaturated linolenic esters.The iso-propyl caprylate and the iso-propyl linolenate ester synthetic fluids are readily biodegradable in the sea water inoculum under aerobic condition.However,the iso-propyl caprylate is inherently biodegradable because its degradation level and that of the reference chemical sample were already above 60%during the 10-day window period.The SP-SBF and the IO-SBF synthetic fluids have lower aerobic biodegradation values because they contain little quantity of poly aromatic hydrocarbons as evident in their GC-MS profiles.Finally,esters and unsaturated synthetic-based fluid are more rapidly biodegradable than paraffinic synthetic fluids and the rate of biodegradation of organic compounds decreases as molecular weight increases.
文摘Recently,nanoparticles have proven to enhance oil recovery on the core-flood scale in challenging high-pressure high-temperature reservoirs.Nanomaterials generally appear to improve oil production through wettability alteration and reduction in interfacial tension between oil and water phases.Besides,they are environmentally friendly and cost-effective enhanced oil recovery techniques.Studying the rheological properties of nanoparticles is critical for field applications.The instability of nanoparticle dispersion due to aggregation is considered as an unfavorable phenomenon in nanofluid flooding while conducting an EOR process.In this study,wettability behavior and rheological properties of surface-treated silica nanoparticles using internal olefins sulfonates(IOS20–24 and IOS19–23),anionic surfactants were investigated.Surface modification effect on the stability of the colloidal solution in porous media and oil recovery was inspected.The rheology of pure and surfacetreated silica nanoparticles was investigated using a HPHT rheometer.Morphology and particle size distributions of pure and coated silica nanoparticles were studied using a field emission scanning electron microscope.A series of core-flood runs was conducted to evaluate the oil recovery factor.The coated silica nanoparticles were found to alter rheological properties and exhibited a shear-thinning behavior as the stability of the coated silica nanoparticles could be improved considerably.At low shear rates,the viscosity slightly increases,and the opposite happens at higher shear rates.Furthermore,the surfacemodified silica nanoparticles were found to alter the wettability of the aqueous phase into strongly water-wet by changing the contact angle from 80°to 3°measured against glass slides representing sandstone rocks.Oil–water IFT results showed that the surface treatment by surfactant lowered the oil–water IFT by 30%.Also,the viscosity of brine increased from 0.001 to 0.008 Pa s by introducing SiO2 nanoparticles to the aqueous phase for better displacement efficiency during chemicalassisted EOR.The core-flood experiments revealed that the ultimate oil recovery is increased by approximately 13%with a surfactant-coated silica nanofluid flood after the conventional waterflooding that proves the potential of smart nanofluids for enhancing oil recovery.The experimental results imply that the use of surfactant-coated nanoparticles in tertiary oil recovery could facilitate the displacement efficiency,alter the wettability toward more water-wet and avoid viscous fingering for stable flood front and additional oil recovery.
文摘With special drilling operation equipment and specific conditions of geology, how does drilling fluid carry cuttings effectively? So far, it is still an urgent problem for drilling researchers to study. This work just aims at the actual engineering background to develop studying model. In this paper, according to non Newtonian fluid mechanics, the law of the solid liquid, two phase fluid flow and actual drilling engineering, the major factors affecting cuttings transport are drilling fluid velocity, hole inclination and fluid rheological properties. Getting a clear understanding of the law of drilling fluid and its cutting taking mechanism, this paper puts forward a model for analysis of field data and quantitative forecast of cutting taking capability of drilling fluid. The full scale annular test section was 6.1 m with 76 and 114 mm drillpipe in a 203 mm ID (wellbore diameter). Hole angle varied from 0° to 90°.
文摘A set of experimental data obtained at the Institute of Physics and Power Engineering in a vertical bundle cooled with supercritical R-12 was analyzed. The test section was a 7-element bundle installed in a hexagonal flow channel with three grid spacers. Data was collected at pressures of approximately 4.65 MPa for several different combinations of wall and bulk-fluid temperatures that were below, at, or above pseudocritical conditions. Analysis of the data has confirmed that there are three distinct heat-transfer regimes for forced convention in supercritical fluids： （1） normal heat transfer, （2） deteriorated heat transfer, and （3） enhanced heat transfer. It was also confirmed that the effects of spacers are evident which was previously observed in sub-critical experimental data. This work compares the wall and bulk fluid temperature data of the experiments to predictions based upon current 1-D correlations for heat transfer in supercritical fluids.
文摘The development of shale reservoirs has brought a paradigm shift in the worldwide energy equation.This entails developing robust techniques to properly evaluate and unlock the potential of those reservoirs.The application of Nuclear Magnetic Resonance techniques in fluid typing and properties estimation is well-developed in conventional reservoirs.However,Shale reservoirs characteristics like pore size,organic matter,clay content,wettability,adsorption,and mineralogy would limit the applicability of the used interpretation methods and correlation.Some of these limitations include the inapplicability of the controlling equations that were derived assuming fast relaxation regime,the overlap of different fluids peaks and the lack of robust correlation to estimate fluid properties in shale.This study presents a state-of-the-art review of the main contributions presented on fluid typing methods and correlations in both experimental and theoretical side.The study involves Dual Tw,Dual Te,and doping agent's application,T1-T2,D-T2 and T2sec vs.T1/T2 methods.In addition,fluid properties estimation such as density,viscosity and the gas-oil ratio is discussed.This study investigates the applicability of these methods along with a study of the current fluid properties correlations and their limitations.Moreover,it recommends the appropriate method and correlation which are capable of tackling shale heterogeneity.
基金the University Grants Commission,New Delhi for supporting financially under Major Research Project(Grant No. 41-790/2012(SR))
文摘We investigate, in this paper, the effects of thermo-physical properties on the flow and heat transfer in a thin film of a power-law liquid over a horizontal stretching surface in the presence of a viscous dissipation. The fluid properties, namely the fluid viscosity and the fluid thermal conductivity, are assumed to vary with temperature. Using a similarity transformation, the governing partial differential equations with a time dependent boundary are converted into coupled non-linear Ordinary Differential Equations （ODEs） with variable coefficients. Numerical solutions of the coupled ODEs are obtained by a finite difference scheme known as the Keller-box method. Results for the velocity and temperature distributions are presented graphically for different values of the pertinent parameters. The effects of unsteady parameter on the skin friction, the wall temperature gradient and the film thickness are presented and analyzed for zero and non-zero values of the temperature-dependent thermo-physical properties. The results obtained reveal many interesting features that warrant further study on the non-Newtonian thin film fluid flow phenomena, especially the shear-thinning phenomena.
文摘A generalized geoacoustic model of fluid mud layer in Chanaiiang Estuary and Hangzhou Bay has been derived from a large amount of in-situ measurements of bulk density (p) profiles of the lay6rs and of lab measurements of acoustic velocities (c) and attenuation coefficients (o) of the fluid mud samples with different values of p for four frequencies of 100 kHz, 150 kHz, 500 kHz, 1500 kHz. The main features of the geoacoustic model can be expressed as follows: from the upper boundary, the bulk density of the fiuid mud increases linearly with depth z, however there is a gradient change (knee) when p is about 12.5 kN/m', then p increases linearly to a value about 15.0 kN/m'. After p more than 15.0, the fluid mud layer quickly transform into an ooze layer. In the fluid mud layer, the acoustic velocity c can be regarded as constant since its variation with z less than 1.5%, and a minimum vaue of c ekists when p is about 13.5 kN/m'. The variations of β with p and with frequency f are linear. Based on the geo-acoustic model and the ray theory, simulations of sound refiection from the fluid mud layers have been made, and some significallt results obtained, from which the bulk density profiles of fluld mud layers can be derived inversely.
