A numerical model based on measured fictive temperature distributions is explored to evaluate the residual stress fields of CO_(2)laser-annealed mitigated fused silica damage sites.The proposed model extracts the resi...A numerical model based on measured fictive temperature distributions is explored to evaluate the residual stress fields of CO_(2)laser-annealed mitigated fused silica damage sites.The proposed model extracts the residual strain from the differences in thermoelastic contraction of fused silica with different fictive temperatures from the initial frozen-in temperatures to ambient temperature.The residual stress fields of mitigated damage sites for the CO_(2)laser-annealed case are obtained by a finite element analysis of equilibrium equations and constitutive equations.The simulated results indicate that the proposed model can accurately evaluate the residual stress fields of laser-annealed mitigated damage sites with a complex thermal history.The calculated maximum hoop stress is in good agreement with the reported experimental result.The estimated optical retardance profiles from the calculated radial and hoop stress fields are consistent with the photoelastic measurements.These results provide sufficient evidence to demonstrate the suitability of the proposed model for describing the residual stresses of mitigated fused silica damage sites after CO_(2)laser annealing.展开更多
The urgent need to develop customized functional products only possible by 3D printing had realized when faced with the unavailability of medical devices like surgical instruments during the coronavirus-19 disease and...The urgent need to develop customized functional products only possible by 3D printing had realized when faced with the unavailability of medical devices like surgical instruments during the coronavirus-19 disease and the ondemand necessity to perform surgery during space missions.Biopolymers have recently been the most appropriate option for fabricating surgical instruments via 3D printing in terms of cheaper and faster processing.Among all 3D printing techniques,fused deposition modelling(FDM)is a low-cost and more rapid printing technique.This article proposes the fabrication of surgical instruments,namely,forceps and hemostat using the fused deposition modeling(FDM)process.Excellent mechanical properties are the only indicator to judge the quality of the functional parts.The mechanical properties of FDM-processed parts depend on various process parameters.These parameters are layer height,infill pattern,top/bottom pattern,number of top/bottom layers,infill density,flow,number of shells,printing temperature,build plate temperature,printing speed,and fan speed.Tensile strength and modulus of elasticity are chosen as evaluation indexes to ascertain the mechanical properties of polylactic acid(PLA)parts printed by FDM.The experiments have performed through Taguchi’s L27orthogonal array(OA).Variance analysis(ANOVA)ascertains the significance of the process parameters and their percent contributions to the evaluation indexes.Finally,as a multiobjective optimization technique,grey relational analysis(GRA)obtains an optimal set of FDM process parameters to fabricate the best parts with comprehensive mechanical properties.Scanning electron microscopy(SEM)examines the types of defects and strong bonding between rasters.The proposed research ensures the successful fabrication of functional surgical tools with substantial ultimate tensile strength(42.6 MPa)and modulus of elasticity(3274 MPa).展开更多
Ideal tissue engineering scaffolds need interconnected pores and high porosity to enable cell survival,migration,proliferation,and differentiation.However,obtaining a high-resolution structure is difficult with tradit...Ideal tissue engineering scaffolds need interconnected pores and high porosity to enable cell survival,migration,proliferation,and differentiation.However,obtaining a high-resolution structure is difficult with traditional one-temperature control fused deposition modeling(FDM).In this study,we propose a dual-temperature control method to improve printability.A numerical model is developed in which the viscosity is a function of temperature and shear rate to study the influence of two different temperature control modes.Quantitative tests are used to assess filament formation and shape fidelity,including one-dimensional filament printing,deposition at corners,fusion,and collapse.By using dual-temperature control,the width of the deposited poly(ε-caprolactone)filament is reduced to 50μm.The comparative results of both the experimental method and numerical simulation suggest that the dual-temperature control FDM can manufacture spatially arranged constructs and presents a promising application in tissue engineering。展开更多
In recent years,the introduction of fused rings own high density and low sensitivity has promoted the development of energetic materials.However,the development of energetic compounds containing fused and bridged ring...In recent years,the introduction of fused rings own high density and low sensitivity has promoted the development of energetic materials.However,the development of energetic compounds containing fused and bridged rings by introducing multiple nitrogen heterocycles at different sites of fused rings is still difficult to progress,which seriously limits the emergence of advanced energetic compounds.In this study,a series of energetic materials choosing different nitrogen rich heterocycles at the vacancies of the fused ring,i.e.,neutral compound 5,6 and their ionic derivatives(compounds 7-12)were designed and synthesized.Compounds 5 and 6 were further confirmed by single crystal X-ray diffraction,while the crystal analysis and theoretical calculations were carried out to explore the relationship between crystal structure and physicochemical properties.All of the newly synthesized compounds(5-12)are insensitive to mechanical stimulation(IS>40 J;FS≥342 N)and they own the high detonation velocity(D:8322-9075 m/s).Notably,hydrazine salt 11 own the higher detonation velocity(9075 m/s)and powder density(1.83 g/cm^(3)),but exhibits lower sensitivity(IS>40 J)than the classical energetic compound RDX(8795 m/s,1.80 g/cm^(3),7.5 J).It is obvious that the combination of 5,6-fused triazolo-triazine and nitropyrazole-tetrazole may be a new energetic skeleton for synthesising the heterocyclic compounds with balanced energy-stability.展开更多
Humankind is facing another deadliest pandemic of all times in history,caused by COVID-19.Apart from this challenging pandemic,World Health Organization(WHO)considers tuberculosis(TB)as a preeminent infectious disease...Humankind is facing another deadliest pandemic of all times in history,caused by COVID-19.Apart from this challenging pandemic,World Health Organization(WHO)considers tuberculosis(TB)as a preeminent infectious disease due to its high infection rate.Generally,both TB and COVID-19 severely affect the lungs,thus hardening the job of medical practitioners who can often misidentify these diseases in the current situation.Therefore,the time of need calls for an immediate and meticulous automatic diagnostic tool that can accurately discriminate both diseases.As one of the preliminary smart health systems that examine three clinical states(COVID-19,TB,and normal cases),this study proposes an amalgam of image filtering,data-augmentation technique,transfer learning-based approach,and advanced deep-learning classifiers to effectively segregate these diseases.It first employed a generative adversarial network(GAN)and Crimmins speckle removal filter on X-ray images to overcome the issue of limited data and noise.Each pre-processed image is then converted into red,green,and blue(RGB)and Commission Internationale de l’Elcairage(CIE)color spaces from which deep fused features are formed by extracting relevant features using DenseNet121 and ResNet50.Each feature extractor extracts 1000 most useful features which are then fused and finally fed to two variants of recurrent neural network(RNN)classifiers for precise discrimination of threeclinical states.Comparative analysis showed that the proposed Bi-directional long-short-term-memory(Bi-LSTM)model dominated the long-short-termmemory(LSTM)network by attaining an overall accuracy of 98.22%for the three-class classification task,whereas LSTM hardly achieved 94.22%accuracy on the test dataset.展开更多
Deep Learning(DL)is known for its golden standard computing paradigm in the learning community.However,it turns out to be an extensively utilized computing approach in the ML field.Therefore,attaining superior outcome...Deep Learning(DL)is known for its golden standard computing paradigm in the learning community.However,it turns out to be an extensively utilized computing approach in the ML field.Therefore,attaining superior outcomes over cognitive tasks based on human performance.The primary benefit of DL is its competency in learning massive data.The DL-based technologies have grown faster and are widely adopted to handle the conventional approaches resourcefully.Specifically,various DL approaches outperform the conventional ML approaches in real-time applications.Indeed,various research works are reviewed to understand the significance of the individual DL models and some computational complexity is observed.This may be due to the broader expertise and knowledge required for handling these models during the prediction process.This research proposes a holistic approach for pneumonia prediction and offers a more appropriate DL model for classification purposes.This work incorporates a novel fused Squeeze and Excitation(SE)block with the ResNet model for pneumonia prediction and better accuracy.The expected model reduces the human effort during the prediction process and makes it easier to diagnose it intelligently as the feature learning is adaptive.The experimentation is carried out in Keras,and the model’s superiority is compared with various advanced approaches.The proposed model gives 90%prediction accuracy,93%precision,90%recall and 89%F1-measure.The proposed model shows a better trade-off compared to other approaches.The evaluation is done with the existing standard ResNet model,GoogleNet+ResNet+DenseNet,and different variants of ResNet models.展开更多
The rapid growth in data generation and increased use of computer network devices has amplified the infrastructures of internet.The interconnectivity of networks has brought various complexities in maintaining network...The rapid growth in data generation and increased use of computer network devices has amplified the infrastructures of internet.The interconnectivity of networks has brought various complexities in maintaining network availability,consistency,and discretion.Machine learning based intrusion detection systems have become essential to monitor network traffic for malicious and illicit activities.An intrusion detection system controls the flow of network traffic with the help of computer systems.Various deep learning algorithms in intrusion detection systems have played a prominent role in identifying and analyzing intrusions in network traffic.For this purpose,when the network traffic encounters known or unknown intrusions in the network,a machine-learning framework is needed to identify and/or verify network intrusion.The Intrusion detection scheme empowered with a fused machine learning technique(IDS-FMLT)is proposed to detect intrusion in a heterogeneous network that consists of different source networks and to protect the network from malicious attacks.The proposed IDS-FMLT system model obtained 95.18%validation accuracy and a 4.82%miss rate in intrusion detection.展开更多
Naturalfibre as a reinforcing agent has been widely used in many industrial applications.Nevertheless,several factors need to be considered,such as the size and weight percentage of thefibre used in binding.Using fused ...Naturalfibre as a reinforcing agent has been widely used in many industrial applications.Nevertheless,several factors need to be considered,such as the size and weight percentage of thefibre used in binding.Using fused deposition modelling(FDM),this factor was investigated by varying the size of naturalfibre as the responding variable with afixed weight percentage of kenaffibre.The process of modifying the naturalfibre in terms of size might increase the dispersion of kenaffibre in the polymer matrix and increase the adhesion bonding between thefibre and matrix of composites,subsequently improving the interfacial bonding between these two phases.In this paper,the effect offibre size was evaluated by performing the mechanical test,Scanning Electron Micrograph(SEM)to observe the morphology of the composites,and also by surface analysis.The surface roughness was visualised using a 3D profilometer and thefigure was illustrated as colour shading in the image.The composite withfibre size≤100μm displayed better tensile andflexural strength,compared to other sizes.In conclusion,by reducing the size of thefibre,the composites could develop high strength performance for industrial applications.展开更多
Approximately 450 million tons of plastic and agricultural waste are produced each year in the world. Only a small portion of this plastic waste is recycled, and a small portion of this agricultural waste is used as f...Approximately 450 million tons of plastic and agricultural waste are produced each year in the world. Only a small portion of this plastic waste is recycled, and a small portion of this agricultural waste is used as fuel or fertilizer, and the rest of this waste is left in the environment or is burned, resulting in environmental and air pollution. For proper disposal, plastic and agricultural waste can be used in the manufacture of composites as raw materials. In this study, we had evaluated the use of bean pod powder (BPp) was used as natural reinforcing filler in recycled polypropylene (rPP) based composites. BPp/rPP composite filaments were developed using the extrusion method and the samples were printed by Fused Filament Fabrication (FFF). Composites with rPP matrix containing different weight fractions of BPp (5%, 10% and 15%) were fabricated to observe and compare the mechanical properties (tensile, flexural, and compressive strength) of the filament composites. In addition, the filament surface was analyzed for roughness and particle size of bean pod powder. The results established that BPp/rPP composites exhibited better tensile, flexural, and compressive strength than rPP and pure PP. By adding 5 wt% BPp, the tensile strength of rPP increased from 20.4 MPa to 22.8 MPa. The highest flexural strength (15.05 MPa) was obtained at 5 wt% BPp among all composites and the highest compressive strength (24.5 MPa), was obtained at 10 wt% BPp. Therefore, it can be concluded that by carefully selecting the ratio of BPp to bean pod powder, it is therefore possible to positively influence the mechanical properties of the resulting composite.展开更多
Poly[R-3-hydroxybutyrate-co-(R-3-hydroxyvalerate)] (PHBVs) copolymers are promising biopolymers, which could substitute petroleum-based plastics for various applications. PHB and PHBV pellets were processed on a custo...Poly[R-3-hydroxybutyrate-co-(R-3-hydroxyvalerate)] (PHBVs) copolymers are promising biopolymers, which could substitute petroleum-based plastics for various applications. PHB and PHBV pellets were processed on a customized 3D printer via Fused Granular Manufacturing (FGM) approach modified with a Mahor screw extruder. To anticipate the behaviour of PHBVs when transformed using conventional thermo-mechanical shaping processes, thermal and mechanical analyses were carried out in order to better understand the effect of annealing temperature on their crystallization behaviour and mechanical properties of PHB polymer and PHBV copolymer. The objectives of the present work were to propose an experimental strategy to study the melting and crystallization events, crystalline structure changes, and mechanical performances of both PHB homopolymer and PHBV copolymer according to identical thermal annealing treatments. A monitoring of 3D printed PHB and PHBV structures was achieved by coupling Differential Scanning Calorimetry (DSC) and tensile tests. .展开更多
High-density poly-ethylene (HDPE) is a nonbiodegradable recyclable plastic which is widely utilized in single use packaging applications. Consequently, it constitutes a significant amount of plastic waste found in lan...High-density poly-ethylene (HDPE) is a nonbiodegradable recyclable plastic which is widely utilized in single use packaging applications. Consequently, it constitutes a significant amount of plastic waste found in landfills. From literature, it has been shown that parts produced using composites of HDPE with carbohydrate-based polymers, such as thermoplastic starch (TPS), experience mechanical degradation through hydrolytic degradation process. The possible utilization of recycled-HDPE (rHDPE) and TPS composite in nonconventional manufacturing processes such as Fused filament fabrication (FFF) has however not been explored. This study explores the potential application of rHDPE and TPS composites in FFF and optimizes the extrusion process parameters used in rHDPE-TPS filament production process. Taguchi method was utilized to analyze the extrusion process. The extrusion process parameters studied were the spooling speed, extrusion speed and the extrusion temperatures. The response variable studied was the filament diameter. In this research, the maximum TPS content achieved during filament production was 40 wt%. This filament was however challenging to use in FFF printers due to frequent nozzle clogging. Printing was therefore done with filaments that contained 0 - 30 wt% TPS. The experimental results showed that the most significant parameter in extrusion process was the spooling speed, followed by extrusion speed. Extrusion temperature had the least significant influence on the filament diameter. It was observed that increase in TPS content resulted in reduced warping and increased rate of hydrolytic degradation. Mechanical properties of printed parts were investigated and the results showed that increasing TPS content resulted in reduction in tensile strength, reduction in compression strength and increase in stiffness. The findings of this research provide valuable insights to plastic recycling industries and researchers regarding the utilization of recycled HDPE and TPS composites as substitute materials in FFF.展开更多
In the grinding of high quality fused silica parts with complex surface or structure using ball-headed metal bonded diamond wheel with small diameter,the existing dressing methods are not suitable to dress the ball-he...In the grinding of high quality fused silica parts with complex surface or structure using ball-headed metal bonded diamond wheel with small diameter,the existing dressing methods are not suitable to dress the ball-headed diamond wheel precisely due to that they are either on-line in process dressing which may causes collision problem or without consideration for the effects of the tool setting error and electrode wear.An on-machine precision preparation and dressing method is proposed for ball-headed diamond wheel based on electrical discharge machining.By using this method the cylindrical diamond wheel with small diameter is manufactured to hemispherical-headed form.The obtained ball-headed diamond wheel is dressed after several grinding passes to recover geometrical accuracy and sharpness which is lost due to the wheel wear.A tool setting method based on high precision optical system is presented to reduce the wheel center setting error and dimension error.The effect of electrode tool wear is investigated by electrical dressing experiments,and the electrode tool wear compensation model is established based on the experimental results which show that the value of wear ratio coefficient K' tends to be constant with the increasing of the feed length of electrode and the mean value of K' is 0.156.Grinding experiments of fused silica are carried out on a test bench to evaluate the performance of the preparation and dressing method.The experimental results show that the surface roughness of the finished workpiece is 0.03 μm.The effect of the grinding parameter and dressing frequency on the surface roughness is investigated based on the measurement results of the surface roughness.This research provides an on-machine preparation and dressing method for ball-headed metal bonded diamond wheel used in the grinding of fused silica,which provides a solution to the tool setting method and the effect of electrode tool wear.展开更多
Three-dimensional porous poly-lactic acid(PLA) scaffold was fabricated using fused deposition modeling(FDM) method including 30%, 50% and 70% nominal porosity. Study of phases in initial polymeric material and printed...Three-dimensional porous poly-lactic acid(PLA) scaffold was fabricated using fused deposition modeling(FDM) method including 30%, 50% and 70% nominal porosity. Study of phases in initial polymeric material and printed scaffolds was done by X-ray diffraction(XRD), and no significant phase difference was observed due to the manufacturing process, and the poly-lactic acid retains its crystalline properties. The results of the mechanical properties evaluation by the compression test show that the mechanical properties of the scaffold have decreased significantly with increasing the porosity of scaffold. The microstructure of scaffolds were studied by scanning electron microscope(SEM), showing that the pores had a regular arrangement and their morphology changed with porosity change. The mechanical properties of the poly-lactic acid scaffolds printed using fused deposition modeling, can be adapted to the surrounding tissue, by porosity change.展开更多
Inhomogeneity and low efficiency are two important factors that limit the application of laser-induced periodic surface structures(LIPSSs),especially on glass surfaces.In this study,two-beam interference(TBI)of femtos...Inhomogeneity and low efficiency are two important factors that limit the application of laser-induced periodic surface structures(LIPSSs),especially on glass surfaces.In this study,two-beam interference(TBI)of femtosecond lasers was used to produce large-area straight LIPSSs on fused silica using cylindrical lenses.Compared with those produced us-ing a single circular or cylindrical lens,the LIPSSs produced by TBI are much straighter and more regular.Depending on the laser fluence and scanning velocity,LIPSSs with grating-like or spaced LIPSSs are produced on the fused silica sur-face.Their structural colors are blue,green,and red,and only green and red,respectively.Grating-like LIPSS patterns oriented in different directions are obtained and exhibit bright and vivid colors,indicating potential applications in surface coloring and anti-counterfeiting logos.展开更多
Fused deposition modelling(FDM), a widely used rapid prototyping process, is a promising technique in manufacturing engineering. In this work, a method for characterizing elastic constants of FDM-fabricated materials ...Fused deposition modelling(FDM), a widely used rapid prototyping process, is a promising technique in manufacturing engineering. In this work, a method for characterizing elastic constants of FDM-fabricated materials is proposed. First of all, according to the manufacturing process of FDM, orthotropic constitutive model is used to describe the mechanical behavior. Then the virtual fields method(VFM) is applied to characterize all the mechanical parameters(Q_(11), Q_(22), Q_(12), Q_(66)) using the full-field strain,which is measured by digital image correlation(DIC). Since the principal axis of the FDM-fabricated structure is sometimes unknown due to the complexity of the manufacturing process, a disk in diametrical compression is used as the load configuration so that the loading angle can be changed conveniently. To verify the feasibility of the proposed method, finite element method(FEM) simulation is conducted to obtain the strain field of the disk. The simulation results show that higher accuracy can be achieved when the loading angle is close to 30?. Finally, a disk fabricated by FDM was used for the experiment. By rotating the disk, several tests with different loading angles were conducted. To determine the position of the principal axis in each test, two groups of parameters(Q_(11), Q_(22), Q_(12), Q_(66)) are calculated by two different groups of virtual fields. Then the corresponding loading angle can be determined by minimizing the deviation between two groups of the parameters. After that, the four constants(Q_(11), Q_(22), Q_(12), Q_(66)) were determined from the test with an angle of 27?.展开更多
Fused deposition modelling (FDM) is a fast growing rapid prototyping (RP) technology due to its ability to build functional parts having complex geometrical shapes in reasonable build time. The dimensional accuracy, s...Fused deposition modelling (FDM) is a fast growing rapid prototyping (RP) technology due to its ability to build functional parts having complex geometrical shapes in reasonable build time. The dimensional accuracy, surface roughness, mechanical strength and above all functionality of built parts are dependent on many process variables and their settings. In this study, five important process parameters such as layer thickness, orientation, raster angle, raster width and air gap have been considered to study their effects on three responses viz., tensile, flexural and impact strength of test specimen. Experiments have been conducted using central composite design (CCD) and empirical models relating each response and process parameters have been developed. The models are validated using analysis of variance (ANOVA). Finally, bacterial foraging technique is used to suggest theoretical combination of parameter settings to achieve good strength simultaneously for all responses.展开更多
A novel fiber Bragg grating(FBG)sensor with three-dimensional(3D)fused deposition modeling(FDM)approach is proposed for effective stress measurement in soil mass.The three-diaphragm structure design is developed to me...A novel fiber Bragg grating(FBG)sensor with three-dimensional(3D)fused deposition modeling(FDM)approach is proposed for effective stress measurement in soil mass.The three-diaphragm structure design is developed to measure earth and water pressures simultaneously.The proposed transducer has advantages of small size,high sensitivity,low cost,immunity to electromagnetic interference and rapid prototyping.The working principle,design parameters,and manufacturing details are discussed.The proposed transducer was calibrated for earth and water pressures measurement by using weights and a specially designed pressure chamber,respectively.The calibration results showed that the wavelength of the transducer was proportional to the applied pressure.The sensitivity coefficients of the earth and water pressures were 12.633 nm/MPa and 6.282 nm/MPa,respectively.Repeated tests and error analysis demonstrated the excellent stability and accuracy of the earth and water pressure measurements.The performance of the proposed transducer was further verified by a model experimental test and numerical analysis,which indicated that the proposed transducer has great potential for practical applications.展开更多
Microstructure of the deepest zone of high speed steel W6Mo5Cr4V2（M2）melt after laser fu-sion was found to be so fine as the ehill zone of a solidified ingot.When narrower chill zoneformed,the long columnar dendrite...Microstructure of the deepest zone of high speed steel W6Mo5Cr4V2（M2）melt after laser fu-sion was found to be so fine as the ehill zone of a solidified ingot.When narrower chill zoneformed,the long columnar dendrites grow into the melt and then the fine equiaxed cellularstructure appears in upper melt region nearly surface.The substructure of cellular grains anddendrites was observed to consist of martensite and retained austenile,while the carbides asM<sub>6</sub>C<sub>■</sub> Cr<sub>7</sub>C<sub>3</sub> and MC distributed at their boundaries.It is believed that the highermicrohardness up to HV<sub>0.1</sub>=865—960 of the laser fused structure of the alloy is due to the oc-currence of martensite.展开更多
基金Project supported by the National Natural Science Foundation of China(Grant No.62275235).
文摘A numerical model based on measured fictive temperature distributions is explored to evaluate the residual stress fields of CO_(2)laser-annealed mitigated fused silica damage sites.The proposed model extracts the residual strain from the differences in thermoelastic contraction of fused silica with different fictive temperatures from the initial frozen-in temperatures to ambient temperature.The residual stress fields of mitigated damage sites for the CO_(2)laser-annealed case are obtained by a finite element analysis of equilibrium equations and constitutive equations.The simulated results indicate that the proposed model can accurately evaluate the residual stress fields of laser-annealed mitigated damage sites with a complex thermal history.The calculated maximum hoop stress is in good agreement with the reported experimental result.The estimated optical retardance profiles from the calculated radial and hoop stress fields are consistent with the photoelastic measurements.These results provide sufficient evidence to demonstrate the suitability of the proposed model for describing the residual stresses of mitigated fused silica damage sites after CO_(2)laser annealing.
文摘The urgent need to develop customized functional products only possible by 3D printing had realized when faced with the unavailability of medical devices like surgical instruments during the coronavirus-19 disease and the ondemand necessity to perform surgery during space missions.Biopolymers have recently been the most appropriate option for fabricating surgical instruments via 3D printing in terms of cheaper and faster processing.Among all 3D printing techniques,fused deposition modelling(FDM)is a low-cost and more rapid printing technique.This article proposes the fabrication of surgical instruments,namely,forceps and hemostat using the fused deposition modeling(FDM)process.Excellent mechanical properties are the only indicator to judge the quality of the functional parts.The mechanical properties of FDM-processed parts depend on various process parameters.These parameters are layer height,infill pattern,top/bottom pattern,number of top/bottom layers,infill density,flow,number of shells,printing temperature,build plate temperature,printing speed,and fan speed.Tensile strength and modulus of elasticity are chosen as evaluation indexes to ascertain the mechanical properties of polylactic acid(PLA)parts printed by FDM.The experiments have performed through Taguchi’s L27orthogonal array(OA).Variance analysis(ANOVA)ascertains the significance of the process parameters and their percent contributions to the evaluation indexes.Finally,as a multiobjective optimization technique,grey relational analysis(GRA)obtains an optimal set of FDM process parameters to fabricate the best parts with comprehensive mechanical properties.Scanning electron microscopy(SEM)examines the types of defects and strong bonding between rasters.The proposed research ensures the successful fabrication of functional surgical tools with substantial ultimate tensile strength(42.6 MPa)and modulus of elasticity(3274 MPa).
基金The authors gratefully acknowledge the support provided by the National Natural Science Foundation of China(Nos.52250006 and 52075482)the Starry Night Science Fund of Zhejiang University Shanghai Institute for Advanced Study(No.SNZJU-SIAS-004).
文摘Ideal tissue engineering scaffolds need interconnected pores and high porosity to enable cell survival,migration,proliferation,and differentiation.However,obtaining a high-resolution structure is difficult with traditional one-temperature control fused deposition modeling(FDM).In this study,we propose a dual-temperature control method to improve printability.A numerical model is developed in which the viscosity is a function of temperature and shear rate to study the influence of two different temperature control modes.Quantitative tests are used to assess filament formation and shape fidelity,including one-dimensional filament printing,deposition at corners,fusion,and collapse.By using dual-temperature control,the width of the deposited poly(ε-caprolactone)filament is reduced to 50μm.The comparative results of both the experimental method and numerical simulation suggest that the dual-temperature control FDM can manufacture spatially arranged constructs and presents a promising application in tissue engineering。
基金supported by the National Natural Science Foundation of China(Grant No.21875110,22075143)the Science Challenge Projectthe Qing Lan Project for the grant。
文摘In recent years,the introduction of fused rings own high density and low sensitivity has promoted the development of energetic materials.However,the development of energetic compounds containing fused and bridged rings by introducing multiple nitrogen heterocycles at different sites of fused rings is still difficult to progress,which seriously limits the emergence of advanced energetic compounds.In this study,a series of energetic materials choosing different nitrogen rich heterocycles at the vacancies of the fused ring,i.e.,neutral compound 5,6 and their ionic derivatives(compounds 7-12)were designed and synthesized.Compounds 5 and 6 were further confirmed by single crystal X-ray diffraction,while the crystal analysis and theoretical calculations were carried out to explore the relationship between crystal structure and physicochemical properties.All of the newly synthesized compounds(5-12)are insensitive to mechanical stimulation(IS>40 J;FS≥342 N)and they own the high detonation velocity(D:8322-9075 m/s).Notably,hydrazine salt 11 own the higher detonation velocity(9075 m/s)and powder density(1.83 g/cm^(3)),but exhibits lower sensitivity(IS>40 J)than the classical energetic compound RDX(8795 m/s,1.80 g/cm^(3),7.5 J).It is obvious that the combination of 5,6-fused triazolo-triazine and nitropyrazole-tetrazole may be a new energetic skeleton for synthesising the heterocyclic compounds with balanced energy-stability.
文摘Humankind is facing another deadliest pandemic of all times in history,caused by COVID-19.Apart from this challenging pandemic,World Health Organization(WHO)considers tuberculosis(TB)as a preeminent infectious disease due to its high infection rate.Generally,both TB and COVID-19 severely affect the lungs,thus hardening the job of medical practitioners who can often misidentify these diseases in the current situation.Therefore,the time of need calls for an immediate and meticulous automatic diagnostic tool that can accurately discriminate both diseases.As one of the preliminary smart health systems that examine three clinical states(COVID-19,TB,and normal cases),this study proposes an amalgam of image filtering,data-augmentation technique,transfer learning-based approach,and advanced deep-learning classifiers to effectively segregate these diseases.It first employed a generative adversarial network(GAN)and Crimmins speckle removal filter on X-ray images to overcome the issue of limited data and noise.Each pre-processed image is then converted into red,green,and blue(RGB)and Commission Internationale de l’Elcairage(CIE)color spaces from which deep fused features are formed by extracting relevant features using DenseNet121 and ResNet50.Each feature extractor extracts 1000 most useful features which are then fused and finally fed to two variants of recurrent neural network(RNN)classifiers for precise discrimination of threeclinical states.Comparative analysis showed that the proposed Bi-directional long-short-term-memory(Bi-LSTM)model dominated the long-short-termmemory(LSTM)network by attaining an overall accuracy of 98.22%for the three-class classification task,whereas LSTM hardly achieved 94.22%accuracy on the test dataset.
文摘Deep Learning(DL)is known for its golden standard computing paradigm in the learning community.However,it turns out to be an extensively utilized computing approach in the ML field.Therefore,attaining superior outcomes over cognitive tasks based on human performance.The primary benefit of DL is its competency in learning massive data.The DL-based technologies have grown faster and are widely adopted to handle the conventional approaches resourcefully.Specifically,various DL approaches outperform the conventional ML approaches in real-time applications.Indeed,various research works are reviewed to understand the significance of the individual DL models and some computational complexity is observed.This may be due to the broader expertise and knowledge required for handling these models during the prediction process.This research proposes a holistic approach for pneumonia prediction and offers a more appropriate DL model for classification purposes.This work incorporates a novel fused Squeeze and Excitation(SE)block with the ResNet model for pneumonia prediction and better accuracy.The expected model reduces the human effort during the prediction process and makes it easier to diagnose it intelligently as the feature learning is adaptive.The experimentation is carried out in Keras,and the model’s superiority is compared with various advanced approaches.The proposed model gives 90%prediction accuracy,93%precision,90%recall and 89%F1-measure.The proposed model shows a better trade-off compared to other approaches.The evaluation is done with the existing standard ResNet model,GoogleNet+ResNet+DenseNet,and different variants of ResNet models.
文摘The rapid growth in data generation and increased use of computer network devices has amplified the infrastructures of internet.The interconnectivity of networks has brought various complexities in maintaining network availability,consistency,and discretion.Machine learning based intrusion detection systems have become essential to monitor network traffic for malicious and illicit activities.An intrusion detection system controls the flow of network traffic with the help of computer systems.Various deep learning algorithms in intrusion detection systems have played a prominent role in identifying and analyzing intrusions in network traffic.For this purpose,when the network traffic encounters known or unknown intrusions in the network,a machine-learning framework is needed to identify and/or verify network intrusion.The Intrusion detection scheme empowered with a fused machine learning technique(IDS-FMLT)is proposed to detect intrusion in a heterogeneous network that consists of different source networks and to protect the network from malicious attacks.The proposed IDS-FMLT system model obtained 95.18%validation accuracy and a 4.82%miss rate in intrusion detection.
基金The result was obtained through the financial support of the Ministry of Education Malaysia under Grant Number RACER/2019/FKM-CARE/F00408This paper’s publication also funded by UTeM Incentive Jurnal Q00049/JURNAL/2020/FKM.
文摘Naturalfibre as a reinforcing agent has been widely used in many industrial applications.Nevertheless,several factors need to be considered,such as the size and weight percentage of thefibre used in binding.Using fused deposition modelling(FDM),this factor was investigated by varying the size of naturalfibre as the responding variable with afixed weight percentage of kenaffibre.The process of modifying the naturalfibre in terms of size might increase the dispersion of kenaffibre in the polymer matrix and increase the adhesion bonding between thefibre and matrix of composites,subsequently improving the interfacial bonding between these two phases.In this paper,the effect offibre size was evaluated by performing the mechanical test,Scanning Electron Micrograph(SEM)to observe the morphology of the composites,and also by surface analysis.The surface roughness was visualised using a 3D profilometer and thefigure was illustrated as colour shading in the image.The composite withfibre size≤100μm displayed better tensile andflexural strength,compared to other sizes.In conclusion,by reducing the size of thefibre,the composites could develop high strength performance for industrial applications.
文摘Approximately 450 million tons of plastic and agricultural waste are produced each year in the world. Only a small portion of this plastic waste is recycled, and a small portion of this agricultural waste is used as fuel or fertilizer, and the rest of this waste is left in the environment or is burned, resulting in environmental and air pollution. For proper disposal, plastic and agricultural waste can be used in the manufacture of composites as raw materials. In this study, we had evaluated the use of bean pod powder (BPp) was used as natural reinforcing filler in recycled polypropylene (rPP) based composites. BPp/rPP composite filaments were developed using the extrusion method and the samples were printed by Fused Filament Fabrication (FFF). Composites with rPP matrix containing different weight fractions of BPp (5%, 10% and 15%) were fabricated to observe and compare the mechanical properties (tensile, flexural, and compressive strength) of the filament composites. In addition, the filament surface was analyzed for roughness and particle size of bean pod powder. The results established that BPp/rPP composites exhibited better tensile, flexural, and compressive strength than rPP and pure PP. By adding 5 wt% BPp, the tensile strength of rPP increased from 20.4 MPa to 22.8 MPa. The highest flexural strength (15.05 MPa) was obtained at 5 wt% BPp among all composites and the highest compressive strength (24.5 MPa), was obtained at 10 wt% BPp. Therefore, it can be concluded that by carefully selecting the ratio of BPp to bean pod powder, it is therefore possible to positively influence the mechanical properties of the resulting composite.
文摘Poly[R-3-hydroxybutyrate-co-(R-3-hydroxyvalerate)] (PHBVs) copolymers are promising biopolymers, which could substitute petroleum-based plastics for various applications. PHB and PHBV pellets were processed on a customized 3D printer via Fused Granular Manufacturing (FGM) approach modified with a Mahor screw extruder. To anticipate the behaviour of PHBVs when transformed using conventional thermo-mechanical shaping processes, thermal and mechanical analyses were carried out in order to better understand the effect of annealing temperature on their crystallization behaviour and mechanical properties of PHB polymer and PHBV copolymer. The objectives of the present work were to propose an experimental strategy to study the melting and crystallization events, crystalline structure changes, and mechanical performances of both PHB homopolymer and PHBV copolymer according to identical thermal annealing treatments. A monitoring of 3D printed PHB and PHBV structures was achieved by coupling Differential Scanning Calorimetry (DSC) and tensile tests. .
文摘High-density poly-ethylene (HDPE) is a nonbiodegradable recyclable plastic which is widely utilized in single use packaging applications. Consequently, it constitutes a significant amount of plastic waste found in landfills. From literature, it has been shown that parts produced using composites of HDPE with carbohydrate-based polymers, such as thermoplastic starch (TPS), experience mechanical degradation through hydrolytic degradation process. The possible utilization of recycled-HDPE (rHDPE) and TPS composite in nonconventional manufacturing processes such as Fused filament fabrication (FFF) has however not been explored. This study explores the potential application of rHDPE and TPS composites in FFF and optimizes the extrusion process parameters used in rHDPE-TPS filament production process. Taguchi method was utilized to analyze the extrusion process. The extrusion process parameters studied were the spooling speed, extrusion speed and the extrusion temperatures. The response variable studied was the filament diameter. In this research, the maximum TPS content achieved during filament production was 40 wt%. This filament was however challenging to use in FFF printers due to frequent nozzle clogging. Printing was therefore done with filaments that contained 0 - 30 wt% TPS. The experimental results showed that the most significant parameter in extrusion process was the spooling speed, followed by extrusion speed. Extrusion temperature had the least significant influence on the filament diameter. It was observed that increase in TPS content resulted in reduced warping and increased rate of hydrolytic degradation. Mechanical properties of printed parts were investigated and the results showed that increasing TPS content resulted in reduction in tensile strength, reduction in compression strength and increase in stiffness. The findings of this research provide valuable insights to plastic recycling industries and researchers regarding the utilization of recycled HDPE and TPS composites as substitute materials in FFF.
基金supported by National Natural Science Foundation of China(Grant No.50935003)National Numerical Control Major Projects of China(Grant No.2013ZX04001000-215)
文摘In the grinding of high quality fused silica parts with complex surface or structure using ball-headed metal bonded diamond wheel with small diameter,the existing dressing methods are not suitable to dress the ball-headed diamond wheel precisely due to that they are either on-line in process dressing which may causes collision problem or without consideration for the effects of the tool setting error and electrode wear.An on-machine precision preparation and dressing method is proposed for ball-headed diamond wheel based on electrical discharge machining.By using this method the cylindrical diamond wheel with small diameter is manufactured to hemispherical-headed form.The obtained ball-headed diamond wheel is dressed after several grinding passes to recover geometrical accuracy and sharpness which is lost due to the wheel wear.A tool setting method based on high precision optical system is presented to reduce the wheel center setting error and dimension error.The effect of electrode tool wear is investigated by electrical dressing experiments,and the electrode tool wear compensation model is established based on the experimental results which show that the value of wear ratio coefficient K' tends to be constant with the increasing of the feed length of electrode and the mean value of K' is 0.156.Grinding experiments of fused silica are carried out on a test bench to evaluate the performance of the preparation and dressing method.The experimental results show that the surface roughness of the finished workpiece is 0.03 μm.The effect of the grinding parameter and dressing frequency on the surface roughness is investigated based on the measurement results of the surface roughness.This research provides an on-machine preparation and dressing method for ball-headed metal bonded diamond wheel used in the grinding of fused silica,which provides a solution to the tool setting method and the effect of electrode tool wear.
文摘Three-dimensional porous poly-lactic acid(PLA) scaffold was fabricated using fused deposition modeling(FDM) method including 30%, 50% and 70% nominal porosity. Study of phases in initial polymeric material and printed scaffolds was done by X-ray diffraction(XRD), and no significant phase difference was observed due to the manufacturing process, and the poly-lactic acid retains its crystalline properties. The results of the mechanical properties evaluation by the compression test show that the mechanical properties of the scaffold have decreased significantly with increasing the porosity of scaffold. The microstructure of scaffolds were studied by scanning electron microscope(SEM), showing that the pores had a regular arrangement and their morphology changed with porosity change. The mechanical properties of the poly-lactic acid scaffolds printed using fused deposition modeling, can be adapted to the surrounding tissue, by porosity change.
文摘Inhomogeneity and low efficiency are two important factors that limit the application of laser-induced periodic surface structures(LIPSSs),especially on glass surfaces.In this study,two-beam interference(TBI)of femtosecond lasers was used to produce large-area straight LIPSSs on fused silica using cylindrical lenses.Compared with those produced us-ing a single circular or cylindrical lens,the LIPSSs produced by TBI are much straighter and more regular.Depending on the laser fluence and scanning velocity,LIPSSs with grating-like or spaced LIPSSs are produced on the fused silica sur-face.Their structural colors are blue,green,and red,and only green and red,respectively.Grating-like LIPSS patterns oriented in different directions are obtained and exhibit bright and vivid colors,indicating potential applications in surface coloring and anti-counterfeiting logos.
基金the financial support from the National Natural Science Foundation of China (Grants 11672153, 11232008, and 11227801)
文摘Fused deposition modelling(FDM), a widely used rapid prototyping process, is a promising technique in manufacturing engineering. In this work, a method for characterizing elastic constants of FDM-fabricated materials is proposed. First of all, according to the manufacturing process of FDM, orthotropic constitutive model is used to describe the mechanical behavior. Then the virtual fields method(VFM) is applied to characterize all the mechanical parameters(Q_(11), Q_(22), Q_(12), Q_(66)) using the full-field strain,which is measured by digital image correlation(DIC). Since the principal axis of the FDM-fabricated structure is sometimes unknown due to the complexity of the manufacturing process, a disk in diametrical compression is used as the load configuration so that the loading angle can be changed conveniently. To verify the feasibility of the proposed method, finite element method(FEM) simulation is conducted to obtain the strain field of the disk. The simulation results show that higher accuracy can be achieved when the loading angle is close to 30?. Finally, a disk fabricated by FDM was used for the experiment. By rotating the disk, several tests with different loading angles were conducted. To determine the position of the principal axis in each test, two groups of parameters(Q_(11), Q_(22), Q_(12), Q_(66)) are calculated by two different groups of virtual fields. Then the corresponding loading angle can be determined by minimizing the deviation between two groups of the parameters. After that, the four constants(Q_(11), Q_(22), Q_(12), Q_(66)) were determined from the test with an angle of 27?.
文摘Fused deposition modelling (FDM) is a fast growing rapid prototyping (RP) technology due to its ability to build functional parts having complex geometrical shapes in reasonable build time. The dimensional accuracy, surface roughness, mechanical strength and above all functionality of built parts are dependent on many process variables and their settings. In this study, five important process parameters such as layer thickness, orientation, raster angle, raster width and air gap have been considered to study their effects on three responses viz., tensile, flexural and impact strength of test specimen. Experiments have been conducted using central composite design (CCD) and empirical models relating each response and process parameters have been developed. The models are validated using analysis of variance (ANOVA). Finally, bacterial foraging technique is used to suggest theoretical combination of parameter settings to achieve good strength simultaneously for all responses.
基金funding support from the National Natural Science Foundation of China(Grant Nos.41972271 and 42177127)Sanya Science and Education Innovation Park of Wuhan University of Technology(Grant No.2020KF0007)。
文摘A novel fiber Bragg grating(FBG)sensor with three-dimensional(3D)fused deposition modeling(FDM)approach is proposed for effective stress measurement in soil mass.The three-diaphragm structure design is developed to measure earth and water pressures simultaneously.The proposed transducer has advantages of small size,high sensitivity,low cost,immunity to electromagnetic interference and rapid prototyping.The working principle,design parameters,and manufacturing details are discussed.The proposed transducer was calibrated for earth and water pressures measurement by using weights and a specially designed pressure chamber,respectively.The calibration results showed that the wavelength of the transducer was proportional to the applied pressure.The sensitivity coefficients of the earth and water pressures were 12.633 nm/MPa and 6.282 nm/MPa,respectively.Repeated tests and error analysis demonstrated the excellent stability and accuracy of the earth and water pressure measurements.The performance of the proposed transducer was further verified by a model experimental test and numerical analysis,which indicated that the proposed transducer has great potential for practical applications.
文摘Microstructure of the deepest zone of high speed steel W6Mo5Cr4V2（M2）melt after laser fu-sion was found to be so fine as the ehill zone of a solidified ingot.When narrower chill zoneformed,the long columnar dendrites grow into the melt and then the fine equiaxed cellularstructure appears in upper melt region nearly surface.The substructure of cellular grains anddendrites was observed to consist of martensite and retained austenile,while the carbides asM<sub>6</sub>C<sub>■</sub> Cr<sub>7</sub>C<sub>3</sub> and MC distributed at their boundaries.It is believed that the highermicrohardness up to HV<sub>0.1</sub>=865—960 of the laser fused structure of the alloy is due to the oc-currence of martensite.
