In the municipal solid waste incineration process,it is difficult to effectively control the gas oxygen content by setting the air flow according to artificial experience.To address this problem,this paper proposes an...In the municipal solid waste incineration process,it is difficult to effectively control the gas oxygen content by setting the air flow according to artificial experience.To address this problem,this paper proposes an optimization control method of gas oxygen content based on model predictive control.First,a stochastic configuration network is utilized to establish a prediction model of gas oxygen content.Second,an improved differential evolution algorithm that is based on parameter adaptive and t-distribution strategy is employed to address the set value of air flow.Finally,model predictive control is combined with the event triggering strategy to reduce the amount of computation and the controller's frequent actions.The experimental results show that the optimization control method proposed in this paper obtains a smaller degree of fluctuation in the air flow set value,which can ensure the tracking control performance of the gas oxygen content while reducing the amount of calculation.展开更多
Sand production is one of the main obstacles restricting gas extraction efficiency and safety from marine natural gas hydrate(NGH)reservoirs.Particle migration within the NGH reservoir dominates sand production behavi...Sand production is one of the main obstacles restricting gas extraction efficiency and safety from marine natural gas hydrate(NGH)reservoirs.Particle migration within the NGH reservoir dominates sand production behaviors,while their relationships were rarely reported,severely constrains quantitative evaluation of sand production risks.This paper reports the optical observations of solid particle migration and production from micrometer to mesoscopic scales conditioned to gravel packing during depressurization-induced NGH dissociation for the first time.Theoretical evolutionary modes of sand migration are established based on experimental observations,and its implications on field NGH are comprehensively discussed.Five particle migration regimes of local borehole failure,continuous collapse,wormhole expansion,extensive slow deformation,and pore-wall fluidization are proved to occur during depressurization.The types of particle migration regimes and their transmission modes during depressurization are predominantly determined by initial hydrate saturation.In contrast,the depressurization mainly dominates the transmission rate of the particle migration regimes.Furthermore,both the cumulative mass and the medium grain size of the produced sand decrease linearly with increasing initial methane hydrate(MH)saturation.Discontinuous gas bubble emission,expansion,and explosion during MH dissociation delay sand migration into the wellbore.At the same time,continuous water flow is a requirement for sand production during hydrate dissociation by depressurization.The experiments enlighten us that a constitutive model that can illustrate visible particle migration regimes and their transmission modes is urgently needed to bridge numerical simulation and field applications.Optimizing wellbore layout positions or special reservoir treatment shall be important for mitigating sand production tendency during NGH exploitation.展开更多
A self-invented atomization process, in which molten metal is atomized into powder by a high-velocity gas stream carrying solid particles as the atomization medium, was introduced. The characteristics of powders prepa...A self-invented atomization process, in which molten metal is atomized into powder by a high-velocity gas stream carrying solid particles as the atomization medium, was introduced. The characteristics of powders prepared by common gas atomization and dual-phase flow atomization under similar conditions were compared. The experimental results show that the dual-phase flow-atomized powders have average particle sizes that are one-half that of the common gas-atomized particles;additionally, they possess a finer microstructure and higher cooling rate under the same atomization gas pressure and the same gas flow. The Weber number in the crash criteria of liquid atomization is adopted to measure the crash ability of the atomization media. The Weber number of the dual-phase flow atomization medium is the sum of that of the gas and the solid particles. Furthermore, the critical equation of the crash model in dual-phase flow atomization is established, and the main regularities associated with this process were analyzed.展开更多
The present paper presents the structure, features and functions of a computerized system on kinetic analysis and evaluation of gas/solid reactions, KinPreGSR. Kin-PreGSR is a menu driven system, can be operated with ...The present paper presents the structure, features and functions of a computerized system on kinetic analysis and evaluation of gas/solid reactions, KinPreGSR. Kin-PreGSR is a menu driven system, can be operated with MS Windows as workbench in a PC computer. It has been developed using visual C++ with FoxPro hybrid coding technique.KinPreGSR combines the characteristics of gas/solid reactions with the kinetic models as well as mass and heat transfer equations. The database files were established for the apparent activation energies of some reduction and decomposition reactions to allow the prediction of the reaction kinetics to some extents. Outputs can be displayed using graphical or numerical forms. Examples regarding the oxide reduction and carbonate decomposition under isothermal conditions are given to show those functions.展开更多
Possibility of combustible gas production from municipal solid waste （MSW） using hot blast furnace （BF） slag has been studied.The objective of this work is to generate combustible gas from MSW using heated BF slag...Possibility of combustible gas production from municipal solid waste （MSW） using hot blast furnace （BF） slag has been studied.The objective of this work is to generate combustible gas from MSW using heated BF slag.In this experiment,the thermal stability of the MSW was analyzed by thermogravimetric analysis,and effects of temperature,gasifying agent （air,N2,steam） and BF slag on the gas products were investigated at 600？900 ？C.The thermogravimetric analysis indicates that the weight loss of MSW includes four stages：evaporation of the moisture,combustion of volatile materials,burning of carbon residue and burnout of ash.The contents of the combustible gas increase with increasing temperature,and the lower calorific value （LCV） increases rapidly at 600？900 ？C.It is found that volume fraction of CO,H2 and CH4 at different atmospheres increases in the order N2〈air〈steam.It is believed that BF slag acts as the catalyst and the heat carrier,which promotes the gasification reactivity of MSW.展开更多
A three-dimensional Eulerian multiphase model, with closure law according to the kinetic theory of granular flow, was used to study the gas/solid flow behaviors in spout-fluid beds. The influences of the coefficient o...A three-dimensional Eulerian multiphase model, with closure law according to the kinetic theory of granular flow, was used to study the gas/solid flow behaviors in spout-fluid beds. The influences of the coefficient of restitution due to non-ideal particle collisions on the simulated results were tested. It is demonstrated that the simulated result is strongly affected by the coefficient of restitution. Comparison of simulations with experiments in a small spout-fluid bed showed that an appropriate coefficient of restitution of 0.93 was necessary to simulate the flow characteristics in an underdesigned large size of spout-fluid bed coal gasifier with diameter of lm and height of 6m. The internal jet and gas/solid flow patterns at different operating conditions were obtained. The simulations show that an optimal gas/solid flow pattern for coal gasification is found when the spouting gas flow rate is equal to the fluidizing gas flow rate and the total of them is two and a half times the minimum fluidizing gas flow rate. Besides, the radial distributions of particle velocity and gas velocity show similar tendencies; the radial distributions of particle phase pressure due to particle collisions and the particle pseudo-temperature corresponding to the macroscopic kinetic energy of the random particle motion also show similar tendencies. These indicate that both gas drag force and particle collisions dominate the movement of particles.展开更多
The influence of solid particles size,density and loading on the critical gas-inducing impeller speed was investigated in a gas–liquid–solid stirring tank equipped with a hollow Rushton impeller.Three types of solid...The influence of solid particles size,density and loading on the critical gas-inducing impeller speed was investigated in a gas–liquid–solid stirring tank equipped with a hollow Rushton impeller.Three types of solid particles,hollow glass beads with diameters of 300 μm,200 μm,100 μm,and 60 μm,silica gel and desalting resin,were used.It was found that the adding solid particles would change the critical impeller speed.For hollow glass beads and silica gel,whose relative densities were less than or equal to 1.5,the critical impeller speeds increased with the solid loading before reaching the maximum values,and then decreased to a value even lower than that without added solids.The size of the solids also had apparent influence on the critical impeller speed,and larger solid particles correspond to a smaller critical impeller speed.The experimental data also showed that the gasinducing was beneficial to the suspension of the solid particles.展开更多
From the viewpoint of interaction mechanics for solid and gas, a coupled mathematical model was presented for solid coal/rock deformation and gas leak flow in parallel deformable coal seams. Numerical solutions using ...From the viewpoint of interaction mechanics for solid and gas, a coupled mathematical model was presented for solid coal/rock deformation and gas leak flow in parallel deformable coal seams. Numerical solutions using the SIP (Strong Implicit Proce- dure) method to the coupled mathematical model for double parallel coal seams were also developed in detail. Numerical simulations for the prediction of the safety range using protection layer mining were performed with experimental data from a mine with potential danger of coal/gas outbursts. Analyses show that the numerical simulation results are consistent with the measured data in situ.展开更多
A CFD code has been developed based on the conservation principles describing gas and solid flow in fluidized beds. This code is employed to simulate not only the spatiotemporal gas and solid phase velocities and v...A CFD code has been developed based on the conservation principles describing gas and solid flow in fluidized beds. This code is employed to simulate not only the spatiotemporal gas and solid phase velocities and voidage profiles in a two dimensional bed but also fluid dynamics in the jet region. The computational results show that gas flow direction is upward in the entire bed accompanied with random local circulations, whilst solid flow direction is upward at the center and downward near the wall. The radical reason of strong back mixing of solid particles and good transfer behavior between two phases is that the jet entrains solid particles. Numerical calculation indicates that gas velocity, solid velocity and pressure profile have a significant change when the voidage is 0 8. The simulated time averaged voidage profiles agree with the experimental results and simulated data reported by Gidaspow and Ettehadieh(1983). Therefore, CFD model can be regarded as a useful tool to study the jet characteristics in dense gas solid fluidized beds.展开更多
The electromotive force （e.m.f.） of solid oxide fuel cells using biomass produced gas （BPG） as the fuels is calculated at 700-1,200 K using an in-house computer program, based on thermodynamic equilibrium analysis...The electromotive force （e.m.f.） of solid oxide fuel cells using biomass produced gas （BPG） as the fuels is calculated at 700-1,200 K using an in-house computer program, based on thermodynamic equilibrium analysis. Tour program also predicts the concentration of oxygen in the fuel chamber as well as the concentration of equilibrium species such as H2, CO, CO2 and CH4. Compared with using hydrogen as a fuel, the e.m.f. for cells using BPG as the fuels is relative low and strongly influenced by carbon deposition. To remove carbon deposition, the optimum amount of H2O to add is determined at various operating temperatures. Further the e.m.f, for cells based on yttria stabilized zirconia and doped ceria as electrolytes are compared. The study reveals that when using BPG as fuel, the depression of e.m.f, for a SOFC using doped ceria as electrolyte is relatively small when compared with that using Yttria stabilized zirconia.展开更多
The chaotic scale-up approach by matching the Kolmogorov entropy(E_K) proposed by Schouten et al.(1996) was assessed in two geometrically similar gas–solid fluidized bed columns of 0.14 and 0.44 m diameter.We used fo...The chaotic scale-up approach by matching the Kolmogorov entropy(E_K) proposed by Schouten et al.(1996) was assessed in two geometrically similar gas–solid fluidized bed columns of 0.14 and 0.44 m diameter.We used four conditions of our validated new mechanistic scale-up method based on matching the radial profiles of gas holdup where the local dimensionless hydrodynamic parameters were similar as measured by advanced measurement techniques.These experimental conditions were used to evaluate the validity of the chaotic scale-up method,which were selected based on our new mechanistic scale-up methodology.Pressure gauge transducer measurements at the wall and inside the bed at various local radial locations and at three axial heights were used to estimate KE.It was found that the experimental conditions with similar or close radial profiles of the Kolmogorov entropy and with similar or close radial profiles of the gas holdup achieve the similarity in local dimensionless hydrodynamic parameters,and vice versa.展开更多
Electrocatalysis is key to improving energy efficiency,reducing carbon emissions,and providing a sustainable way of meeting global energy needs.Therefore,elucidating electrochemical reaction mechanisms at the electrol...Electrocatalysis is key to improving energy efficiency,reducing carbon emissions,and providing a sustainable way of meeting global energy needs.Therefore,elucidating electrochemical reaction mechanisms at the electrolyte/electrode interfaces is essential for developing advanced renewable energy technologies.However,the direct probing of real-time interfacial changes,i.e.,the surface intermediates,chemical environment,and electronic structure,under operating conditions is challenging and necessitates the use of in situ methods.Herein,we present a new lab-based instrument commissioned to perform in situ chemical analysis at liquid/solid interfaces using ambient pressure X-ray photoelectron spectroscopy(APXPS).This setup takes advantage of a chromium source of tender X-rays and is designed to study liquid/solid interfaces by the“dip and pull”method.Each of the main components was carefully described,and the results of performance tests are presented.Using a three-electrode setup,the system can probe the intermediate species and potential shifts across the liquid electrolyte/solid electrode interface.In addition,we demonstrate how this system allows the study of interfacial changes at gas/solid interfaces using a case study:a sodium–oxygen model battery.However,the use of APXPS in electrochemical studies is still in the early stages,so we summarize the current challenges and some developmental frontiers.Despite the challenges,we expect that joint efforts to improve instruments and the electrochemical setup will enable us to obtain a better understanding of the composition–reactivity relationship at electrochemical interfaces under realistic reaction conditions.展开更多
In order to comply with discharge standards, a gas–solid separator is used to remove solid particles from the thorium molten salt reactor-solid fuel (TMSR-SF) system. As a key component, it directly determines system...In order to comply with discharge standards, a gas–solid separator is used to remove solid particles from the thorium molten salt reactor-solid fuel (TMSR-SF) system. As a key component, it directly determines system energy efficiency. However, current gas–solid separators, based on activated carbon adsorption technology, result in high pressure drops and increased maintenance costs. In the present study, a new combined gas–solid separator was developed for the TMSR-SF. Based on a simplified computational fluid dynamics (CFD) model, the gas–solid twophase flow and the motion trajectory of solid particles were simulated for this new separator using commercial ANSYS 16.0 software. The flow and separation mechanism for this structure were also been discussed in terms of their velocity effects and pressure field distributions, and then the structure was optimized based on the influence of key structural parameters on pressure and separation efficiency. The results showed that the standard k–ε model could be achieved and accurately simulated the new combined separator. In this new combined gas–solid separator, coarse particles are separated in the first stage using rotating centrifugal motion, and then fine particles are filtered in the second stage, giving a separation efficiency of up to 96.11%. The optimum blade inclination angle and numbers were calculated to be 45° and four, respectively. It implicated that the combined separator could be of great significance in a wide variety of applications.展开更多
Solid phase microextraction （SPME） is a solvent-flee method of sample collection. SPME is an appealing method for sample collection because it is designed for the sampling of trace level analytes with short sampling...Solid phase microextraction （SPME） is a solvent-flee method of sample collection. SPME is an appealing method for sample collection because it is designed for the sampling of trace level analytes with short sampling times in a variety of environments. Additionally, SPME can be used to directly deliver a sample to a gas chromatograph （GC） for analysis by means of thermal desorption. In this paper, the performance of SPME under dynamic conditions was investigated. Additionally, the competence of SPME sampling for the simultaneous analysis of multiple trace analytes was also evaluated. This work is discussed in the context of underground mine ventilation surveys but is applicable to any industry in which ventilation circuits must be evaluated. The results of this paper showed that the performance of the 100 ~m PDMS SPME fiber was both precise and rapid under dynamic conditions. This SPME fiber was also able to simultaneously collect sulfur hexafluoride （SF6） and perfluoromethylcyclohexane （PMCH） with adequate sensitivity.展开更多
In the last several decades, circulating fluidized bed reactors have been studied in many aspects including hydrodynamics, heat and mass transfer and gas–solid two phase contacting. However, despite the abundance of ...In the last several decades, circulating fluidized bed reactors have been studied in many aspects including hydrodynamics, heat and mass transfer and gas–solid two phase contacting. However, despite the abundance of review papers on hydrodynamics, there is no summary paper on gas–solid contact efficiency to date, especially on high density circulating fluidized beds(CFBs). This paper gives an introduction to, and a review of the measurement of contact efficiency in circulating fluidized bed riser. Firstly, the popular testing method of contact efficiency including the method of heating transfer experiment and hot model reaction are discussed, then previous published papers are reviewed based on the discussed methods. Some key results of the experimental work are described and discussed. Gas–solid contact efficiency is affected by the operating conditions as well as the particle size distribution. The result of the contact efficiency shows that the CFB riser is far away from an ideal plug flow reactor due to the characteristics of hydrodynamics in the riser. Lacunae in the available literature have been delineated and recommendations have been made for further work.展开更多
As an important form of reactors for gas/liquid/solid catalytic reaction,trickle bed reactors (TBRs) are widely applied in petroleum industry,biochemical,fine chemical and pharmaceutical industries because of their fl...As an important form of reactors for gas/liquid/solid catalytic reaction,trickle bed reactors (TBRs) are widely applied in petroleum industry,biochemical,fine chemical and pharmaceutical industries because of their flexibility,simplicity of operation and high throughput.However,TBRs also show inefficient production and hot pots caused by non-uniform fluid distribution and incomplete wetting of the catalyst,which limit their further application in chemical industry.Also,process intensification in TBRs is necessary as the decrease in quality of processed crude oil,caused by increased exploitation depths,and more restrictive environmental regulations and emission standards for industry,caused by increased environment protection consciousness.In recent years,lots of strategies for process intensification in TBRs have been proposed to improve reaction performance to meet the current and future demands of chemical industry from the environmental and economic perspective.This article summarizes the recent progress in techniques for intensifying gas/liquid/solid reaction in TBRs and application of intensified TBRs in petroleum industry.展开更多
In this work, an analysis of the generation, composition and management of the urban solid waste in Mexico and its relation to greenhouse gas emissions is described;as well a case study in Morelos, a state in the cent...In this work, an analysis of the generation, composition and management of the urban solid waste in Mexico and its relation to greenhouse gas emissions is described;as well a case study in Morelos, a state in the central region of the country. Data were collected from the scientific literature and existing data bases at state and national levels. In addition, the emissions of greenhouse gas were calculated for a period of 14 years, using the Intergovernmental Panel on Climate Change (IPCC) methodology. The municipal solid waste data collected from 1998 to 2012 reveal an increase in the amount of waste generated in Mexico and in Morelos (38% and 43%, respectively), which have been influenced by the urbanization process and the population increase. According to the official data, the composition of the urban solid waste in Mexico, is mostly organic matter (50%), represented by food and garden residues, as well as paper and cardboard (near to 14%). While in Morelos, the percentages of generation for these materials are 44% and 9%, respectively. The management of the urban waste mainly consists of house collection, principally in metropolitan zones and medium and small cities, representing 78.7% in Mexico and 89.2% in Morelos. The second way to eliminate the solid wastes is open burning (mostly in semi-urban and rural areas), representing 14.5% and 6.7% for Mexico and Morelos, respectively. During this period, the nationwide greenhouse gas emissions derived from solid waste management (SWM) increased by 180%, while in Morelos, an increase of 42.5% was calculated. Thus, the population increment and urbanization process were correlated with the rise in the amount of residues generated in Mexico and Morelos.展开更多
A new method for measuring the solid flow rate in gas solid two phase flow is introduced in this paper. An electrically heated probe was put in a gas solid two phase flow. For certain solid particles, the flow medi...A new method for measuring the solid flow rate in gas solid two phase flow is introduced in this paper. An electrically heated probe was put in a gas solid two phase flow. For certain solid particles, the flow media with different velocities and concentrations of particles produced different effects on heat transfer with the probe. The solid flow rate can be measured according to the intensity of heat transfer. Experiments were made on a pilot pneumatic conveying device. Research results prove that the method works effectively and reliably.展开更多
Due to the restriction such as the Minamata Convention as well as the IED of the European Commission,mercury removal from flue gases of coal-fired power plants(CPP)is an increasingly important environmental issue.This...Due to the restriction such as the Minamata Convention as well as the IED of the European Commission,mercury removal from flue gases of coal-fired power plants(CPP)is an increasingly important environmental issue.This makes this topic very crucial for both the energy industry and scientists.This paper shows how mercury arises from natural resources,i.e.,coals,through their combustion processes in CPP and considers the issue of mercury content in flue gases and solid-state coal combustion by-products.The main part of this paper presents a review of the solid sorbents available for elemental mercury control and removal processes,tested on a laboratory scale.The described solutions have a potential for wider usage in exhaust gas treatment processes in the energy production sector.These solutions represent the latest developments in the field of elemental mercury removal from gases.The authors present an overview of the wide range of solid sorbents and their modifications intended to increase affinity for Hg^(0).Among the presented sorbents are the wellknown activated carbon solutions but also novel modifications to these and other innovative sorbent proposals based on,e.g.,zeolites,biochars,other carbon-based materials,metal-organic frameworks.The paper presents a wide range of characteristics of the described sorbents,as well as the conditions for the Hg^(0) removal experiments summarizing the compendium of novel solid sorbent solutions dedicated to the removal of elemental mercury from gases.展开更多
The hydrodynamics is still not fully understood in the three-phase stirred tank equipped with multi-impeller due to the intensive interaction between phases.In this work,the solid critical suspension speed(NJSG),relat...The hydrodynamics is still not fully understood in the three-phase stirred tank equipped with multi-impeller due to the intensive interaction between phases.In this work,the solid critical suspension speed(NJSG),relative power demand(RPD)and overall gas holdup(ε_G)were measured in an air–water–glass beads stirred tank equipped with multi-impeller,which consists of a parabolic blade disk turbine below two down-pumping hydrofoils.Results show that either the NJSGor the specific power consumption increases when increasing the volumetric solid concentration or superficial gas velocity.RPD changes less than 10%when solid volumetric concentration ranges from 0 to 15%.ε_G decreases with the increase of solid concentration,and increases with the increase of both superficial gas velocity and the total specific power consumption.The quantitative correlations of NJSG,RPD andεGwere regressed as the function of superficial gas velocity,specific power consumption,Froude number and gas flow number,in order to provide the reference in the design of such three-phase stirred tank with similar multi-impellers.展开更多
基金supported by the National Natural Science Foundation of China(62373017,62073006)and the Beijing Natural Science Foundation of China(4212032)。
文摘In the municipal solid waste incineration process,it is difficult to effectively control the gas oxygen content by setting the air flow according to artificial experience.To address this problem,this paper proposes an optimization control method of gas oxygen content based on model predictive control.First,a stochastic configuration network is utilized to establish a prediction model of gas oxygen content.Second,an improved differential evolution algorithm that is based on parameter adaptive and t-distribution strategy is employed to address the set value of air flow.Finally,model predictive control is combined with the event triggering strategy to reduce the amount of computation and the controller's frequent actions.The experimental results show that the optimization control method proposed in this paper obtains a smaller degree of fluctuation in the air flow set value,which can ensure the tracking control performance of the gas oxygen content while reducing the amount of calculation.
基金supported by the Laoshan Laboratory(No.LSKJ LSKJ202203506)the Taishan Scholars Program,and the National Natural Science Foundation of China(Grant No.41976074).
文摘Sand production is one of the main obstacles restricting gas extraction efficiency and safety from marine natural gas hydrate(NGH)reservoirs.Particle migration within the NGH reservoir dominates sand production behaviors,while their relationships were rarely reported,severely constrains quantitative evaluation of sand production risks.This paper reports the optical observations of solid particle migration and production from micrometer to mesoscopic scales conditioned to gravel packing during depressurization-induced NGH dissociation for the first time.Theoretical evolutionary modes of sand migration are established based on experimental observations,and its implications on field NGH are comprehensively discussed.Five particle migration regimes of local borehole failure,continuous collapse,wormhole expansion,extensive slow deformation,and pore-wall fluidization are proved to occur during depressurization.The types of particle migration regimes and their transmission modes during depressurization are predominantly determined by initial hydrate saturation.In contrast,the depressurization mainly dominates the transmission rate of the particle migration regimes.Furthermore,both the cumulative mass and the medium grain size of the produced sand decrease linearly with increasing initial methane hydrate(MH)saturation.Discontinuous gas bubble emission,expansion,and explosion during MH dissociation delay sand migration into the wellbore.At the same time,continuous water flow is a requirement for sand production during hydrate dissociation by depressurization.The experiments enlighten us that a constitutive model that can illustrate visible particle migration regimes and their transmission modes is urgently needed to bridge numerical simulation and field applications.Optimizing wellbore layout positions or special reservoir treatment shall be important for mitigating sand production tendency during NGH exploitation.
文摘A self-invented atomization process, in which molten metal is atomized into powder by a high-velocity gas stream carrying solid particles as the atomization medium, was introduced. The characteristics of powders prepared by common gas atomization and dual-phase flow atomization under similar conditions were compared. The experimental results show that the dual-phase flow-atomized powders have average particle sizes that are one-half that of the common gas-atomized particles;additionally, they possess a finer microstructure and higher cooling rate under the same atomization gas pressure and the same gas flow. The Weber number in the crash criteria of liquid atomization is adopted to measure the crash ability of the atomization media. The Weber number of the dual-phase flow atomization medium is the sum of that of the gas and the solid particles. Furthermore, the critical equation of the crash model in dual-phase flow atomization is established, and the main regularities associated with this process were analyzed.
基金supported by the National Natural Science Foundation of China(No.59774023).
文摘The present paper presents the structure, features and functions of a computerized system on kinetic analysis and evaluation of gas/solid reactions, KinPreGSR. Kin-PreGSR is a menu driven system, can be operated with MS Windows as workbench in a PC computer. It has been developed using visual C++ with FoxPro hybrid coding technique.KinPreGSR combines the characteristics of gas/solid reactions with the kinetic models as well as mass and heat transfer equations. The database files were established for the apparent activation energies of some reduction and decomposition reactions to allow the prediction of the reaction kinetics to some extents. Outputs can be displayed using graphical or numerical forms. Examples regarding the oxide reduction and carbonate decomposition under isothermal conditions are given to show those functions.
基金supported by the Applied Basic Research Key Project of Yunnan Province (No.2007E0014Z)
文摘Possibility of combustible gas production from municipal solid waste （MSW） using hot blast furnace （BF） slag has been studied.The objective of this work is to generate combustible gas from MSW using heated BF slag.In this experiment,the thermal stability of the MSW was analyzed by thermogravimetric analysis,and effects of temperature,gasifying agent （air,N2,steam） and BF slag on the gas products were investigated at 600？900 ？C.The thermogravimetric analysis indicates that the weight loss of MSW includes four stages：evaporation of the moisture,combustion of volatile materials,burning of carbon residue and burnout of ash.The contents of the combustible gas increase with increasing temperature,and the lower calorific value （LCV） increases rapidly at 600？900 ？C.It is found that volume fraction of CO,H2 and CH4 at different atmospheres increases in the order N2〈air〈steam.It is believed that BF slag acts as the catalyst and the heat carrier,which promotes the gasification reactivity of MSW.
基金Supported by the National Key Program of Basic Research in China (No.2004CB217702, No.2005CB221202, No.2006CB20030201) and the National Natural Science Foundation of China (No.20590367, No.50676021, No.50606006).
文摘A three-dimensional Eulerian multiphase model, with closure law according to the kinetic theory of granular flow, was used to study the gas/solid flow behaviors in spout-fluid beds. The influences of the coefficient of restitution due to non-ideal particle collisions on the simulated results were tested. It is demonstrated that the simulated result is strongly affected by the coefficient of restitution. Comparison of simulations with experiments in a small spout-fluid bed showed that an appropriate coefficient of restitution of 0.93 was necessary to simulate the flow characteristics in an underdesigned large size of spout-fluid bed coal gasifier with diameter of lm and height of 6m. The internal jet and gas/solid flow patterns at different operating conditions were obtained. The simulations show that an optimal gas/solid flow pattern for coal gasification is found when the spouting gas flow rate is equal to the fluidizing gas flow rate and the total of them is two and a half times the minimum fluidizing gas flow rate. Besides, the radial distributions of particle velocity and gas velocity show similar tendencies; the radial distributions of particle phase pressure due to particle collisions and the particle pseudo-temperature corresponding to the macroscopic kinetic energy of the random particle motion also show similar tendencies. These indicate that both gas drag force and particle collisions dominate the movement of particles.
基金Supported by the National Natural Science Foundation of China(51308215)
文摘The influence of solid particles size,density and loading on the critical gas-inducing impeller speed was investigated in a gas–liquid–solid stirring tank equipped with a hollow Rushton impeller.Three types of solid particles,hollow glass beads with diameters of 300 μm,200 μm,100 μm,and 60 μm,silica gel and desalting resin,were used.It was found that the adding solid particles would change the critical impeller speed.For hollow glass beads and silica gel,whose relative densities were less than or equal to 1.5,the critical impeller speeds increased with the solid loading before reaching the maximum values,and then decreased to a value even lower than that without added solids.The size of the solids also had apparent influence on the critical impeller speed,and larger solid particles correspond to a smaller critical impeller speed.The experimental data also showed that the gasinducing was beneficial to the suspension of the solid particles.
文摘From the viewpoint of interaction mechanics for solid and gas, a coupled mathematical model was presented for solid coal/rock deformation and gas leak flow in parallel deformable coal seams. Numerical solutions using the SIP (Strong Implicit Proce- dure) method to the coupled mathematical model for double parallel coal seams were also developed in detail. Numerical simulations for the prediction of the safety range using protection layer mining were performed with experimental data from a mine with potential danger of coal/gas outbursts. Analyses show that the numerical simulation results are consistent with the measured data in situ.
文摘A CFD code has been developed based on the conservation principles describing gas and solid flow in fluidized beds. This code is employed to simulate not only the spatiotemporal gas and solid phase velocities and voidage profiles in a two dimensional bed but also fluid dynamics in the jet region. The computational results show that gas flow direction is upward in the entire bed accompanied with random local circulations, whilst solid flow direction is upward at the center and downward near the wall. The radical reason of strong back mixing of solid particles and good transfer behavior between two phases is that the jet entrains solid particles. Numerical calculation indicates that gas velocity, solid velocity and pressure profile have a significant change when the voidage is 0 8. The simulated time averaged voidage profiles agree with the experimental results and simulated data reported by Gidaspow and Ettehadieh(1983). Therefore, CFD model can be regarded as a useful tool to study the jet characteristics in dense gas solid fluidized beds.
基金V. ACKN0WLEDGMENT This work was supported by the National Natural Science Foundation of China （No.50372066 and No.50332040）.
文摘The electromotive force （e.m.f.） of solid oxide fuel cells using biomass produced gas （BPG） as the fuels is calculated at 700-1,200 K using an in-house computer program, based on thermodynamic equilibrium analysis. Tour program also predicts the concentration of oxygen in the fuel chamber as well as the concentration of equilibrium species such as H2, CO, CO2 and CH4. Compared with using hydrogen as a fuel, the e.m.f. for cells using BPG as the fuels is relative low and strongly influenced by carbon deposition. To remove carbon deposition, the optimum amount of H2O to add is determined at various operating temperatures. Further the e.m.f, for cells based on yttria stabilized zirconia and doped ceria as electrolytes are compared. The study reveals that when using BPG as fuel, the depression of e.m.f, for a SOFC using doped ceria as electrolyte is relatively small when compared with that using Yttria stabilized zirconia.
基金the Multiphase Reactors Engineering and Applications Laboratory(mReal) for funding and support
文摘The chaotic scale-up approach by matching the Kolmogorov entropy(E_K) proposed by Schouten et al.(1996) was assessed in two geometrically similar gas–solid fluidized bed columns of 0.14 and 0.44 m diameter.We used four conditions of our validated new mechanistic scale-up method based on matching the radial profiles of gas holdup where the local dimensionless hydrodynamic parameters were similar as measured by advanced measurement techniques.These experimental conditions were used to evaluate the validity of the chaotic scale-up method,which were selected based on our new mechanistic scale-up methodology.Pressure gauge transducer measurements at the wall and inside the bed at various local radial locations and at three axial heights were used to estimate KE.It was found that the experimental conditions with similar or close radial profiles of the Kolmogorov entropy and with similar or close radial profiles of the gas holdup achieve the similarity in local dimensionless hydrodynamic parameters,and vice versa.
文摘Electrocatalysis is key to improving energy efficiency,reducing carbon emissions,and providing a sustainable way of meeting global energy needs.Therefore,elucidating electrochemical reaction mechanisms at the electrolyte/electrode interfaces is essential for developing advanced renewable energy technologies.However,the direct probing of real-time interfacial changes,i.e.,the surface intermediates,chemical environment,and electronic structure,under operating conditions is challenging and necessitates the use of in situ methods.Herein,we present a new lab-based instrument commissioned to perform in situ chemical analysis at liquid/solid interfaces using ambient pressure X-ray photoelectron spectroscopy(APXPS).This setup takes advantage of a chromium source of tender X-rays and is designed to study liquid/solid interfaces by the“dip and pull”method.Each of the main components was carefully described,and the results of performance tests are presented.Using a three-electrode setup,the system can probe the intermediate species and potential shifts across the liquid electrolyte/solid electrode interface.In addition,we demonstrate how this system allows the study of interfacial changes at gas/solid interfaces using a case study:a sodium–oxygen model battery.However,the use of APXPS in electrochemical studies is still in the early stages,so we summarize the current challenges and some developmental frontiers.Despite the challenges,we expect that joint efforts to improve instruments and the electrochemical setup will enable us to obtain a better understanding of the composition–reactivity relationship at electrochemical interfaces under realistic reaction conditions.
文摘In order to comply with discharge standards, a gas–solid separator is used to remove solid particles from the thorium molten salt reactor-solid fuel (TMSR-SF) system. As a key component, it directly determines system energy efficiency. However, current gas–solid separators, based on activated carbon adsorption technology, result in high pressure drops and increased maintenance costs. In the present study, a new combined gas–solid separator was developed for the TMSR-SF. Based on a simplified computational fluid dynamics (CFD) model, the gas–solid twophase flow and the motion trajectory of solid particles were simulated for this new separator using commercial ANSYS 16.0 software. The flow and separation mechanism for this structure were also been discussed in terms of their velocity effects and pressure field distributions, and then the structure was optimized based on the influence of key structural parameters on pressure and separation efficiency. The results showed that the standard k–ε model could be achieved and accurately simulated the new combined separator. In this new combined gas–solid separator, coarse particles are separated in the first stage using rotating centrifugal motion, and then fine particles are filtered in the second stage, giving a separation efficiency of up to 96.11%. The optimum blade inclination angle and numbers were calculated to be 45° and four, respectively. It implicated that the combined separator could be of great significance in a wide variety of applications.
基金Contract No.200-2009-31933,awarded by the National Institute for Occupational Safety and Health(NIOSH)
文摘Solid phase microextraction （SPME） is a solvent-flee method of sample collection. SPME is an appealing method for sample collection because it is designed for the sampling of trace level analytes with short sampling times in a variety of environments. Additionally, SPME can be used to directly deliver a sample to a gas chromatograph （GC） for analysis by means of thermal desorption. In this paper, the performance of SPME under dynamic conditions was investigated. Additionally, the competence of SPME sampling for the simultaneous analysis of multiple trace analytes was also evaluated. This work is discussed in the context of underground mine ventilation surveys but is applicable to any industry in which ventilation circuits must be evaluated. The results of this paper showed that the performance of the 100 ~m PDMS SPME fiber was both precise and rapid under dynamic conditions. This SPME fiber was also able to simultaneously collect sulfur hexafluoride （SF6） and perfluoromethylcyclohexane （PMCH） with adequate sensitivity.
基金Supported by the Scientific Research Funds from China University of Petroleum(Beijing)(No.2462014YJRC018)partially supported by the National Natural Science Foundation of China(No.21506253 and No.91534204)
文摘In the last several decades, circulating fluidized bed reactors have been studied in many aspects including hydrodynamics, heat and mass transfer and gas–solid two phase contacting. However, despite the abundance of review papers on hydrodynamics, there is no summary paper on gas–solid contact efficiency to date, especially on high density circulating fluidized beds(CFBs). This paper gives an introduction to, and a review of the measurement of contact efficiency in circulating fluidized bed riser. Firstly, the popular testing method of contact efficiency including the method of heating transfer experiment and hot model reaction are discussed, then previous published papers are reviewed based on the discussed methods. Some key results of the experimental work are described and discussed. Gas–solid contact efficiency is affected by the operating conditions as well as the particle size distribution. The result of the contact efficiency shows that the CFB riser is far away from an ideal plug flow reactor due to the characteristics of hydrodynamics in the riser. Lacunae in the available literature have been delineated and recommendations have been made for further work.
基金the support of National Natural Science Foundation of China(21878019)Beijing Natural Science Foundation(2182063)。
文摘As an important form of reactors for gas/liquid/solid catalytic reaction,trickle bed reactors (TBRs) are widely applied in petroleum industry,biochemical,fine chemical and pharmaceutical industries because of their flexibility,simplicity of operation and high throughput.However,TBRs also show inefficient production and hot pots caused by non-uniform fluid distribution and incomplete wetting of the catalyst,which limit their further application in chemical industry.Also,process intensification in TBRs is necessary as the decrease in quality of processed crude oil,caused by increased exploitation depths,and more restrictive environmental regulations and emission standards for industry,caused by increased environment protection consciousness.In recent years,lots of strategies for process intensification in TBRs have been proposed to improve reaction performance to meet the current and future demands of chemical industry from the environmental and economic perspective.This article summarizes the recent progress in techniques for intensifying gas/liquid/solid reaction in TBRs and application of intensified TBRs in petroleum industry.
文摘In this work, an analysis of the generation, composition and management of the urban solid waste in Mexico and its relation to greenhouse gas emissions is described;as well a case study in Morelos, a state in the central region of the country. Data were collected from the scientific literature and existing data bases at state and national levels. In addition, the emissions of greenhouse gas were calculated for a period of 14 years, using the Intergovernmental Panel on Climate Change (IPCC) methodology. The municipal solid waste data collected from 1998 to 2012 reveal an increase in the amount of waste generated in Mexico and in Morelos (38% and 43%, respectively), which have been influenced by the urbanization process and the population increase. According to the official data, the composition of the urban solid waste in Mexico, is mostly organic matter (50%), represented by food and garden residues, as well as paper and cardboard (near to 14%). While in Morelos, the percentages of generation for these materials are 44% and 9%, respectively. The management of the urban waste mainly consists of house collection, principally in metropolitan zones and medium and small cities, representing 78.7% in Mexico and 89.2% in Morelos. The second way to eliminate the solid wastes is open burning (mostly in semi-urban and rural areas), representing 14.5% and 6.7% for Mexico and Morelos, respectively. During this period, the nationwide greenhouse gas emissions derived from solid waste management (SWM) increased by 180%, while in Morelos, an increase of 42.5% was calculated. Thus, the population increment and urbanization process were correlated with the rise in the amount of residues generated in Mexico and Morelos.
文摘A new method for measuring the solid flow rate in gas solid two phase flow is introduced in this paper. An electrically heated probe was put in a gas solid two phase flow. For certain solid particles, the flow media with different velocities and concentrations of particles produced different effects on heat transfer with the probe. The solid flow rate can be measured according to the intensity of heat transfer. Experiments were made on a pilot pneumatic conveying device. Research results prove that the method works effectively and reliably.
基金This work was supported by the National Centre for Research and Development project LIDER,Contract Number LIDER/384/L-6/14/NCBR/2015.
文摘Due to the restriction such as the Minamata Convention as well as the IED of the European Commission,mercury removal from flue gases of coal-fired power plants(CPP)is an increasingly important environmental issue.This makes this topic very crucial for both the energy industry and scientists.This paper shows how mercury arises from natural resources,i.e.,coals,through their combustion processes in CPP and considers the issue of mercury content in flue gases and solid-state coal combustion by-products.The main part of this paper presents a review of the solid sorbents available for elemental mercury control and removal processes,tested on a laboratory scale.The described solutions have a potential for wider usage in exhaust gas treatment processes in the energy production sector.These solutions represent the latest developments in the field of elemental mercury removal from gases.The authors present an overview of the wide range of solid sorbents and their modifications intended to increase affinity for Hg^(0).Among the presented sorbents are the wellknown activated carbon solutions but also novel modifications to these and other innovative sorbent proposals based on,e.g.,zeolites,biochars,other carbon-based materials,metal-organic frameworks.The paper presents a wide range of characteristics of the described sorbents,as well as the conditions for the Hg^(0) removal experiments summarizing the compendium of novel solid sorbent solutions dedicated to the removal of elemental mercury from gases.
基金the financial support from the National Key R&D Program of China(2017YFB0306703)the Fundamental Research Funds for the Central Universities(XK1802-1)the National Natural Science Foundation of China(No.21676007)。
文摘The hydrodynamics is still not fully understood in the three-phase stirred tank equipped with multi-impeller due to the intensive interaction between phases.In this work,the solid critical suspension speed(NJSG),relative power demand(RPD)and overall gas holdup(ε_G)were measured in an air–water–glass beads stirred tank equipped with multi-impeller,which consists of a parabolic blade disk turbine below two down-pumping hydrofoils.Results show that either the NJSGor the specific power consumption increases when increasing the volumetric solid concentration or superficial gas velocity.RPD changes less than 10%when solid volumetric concentration ranges from 0 to 15%.ε_G decreases with the increase of solid concentration,and increases with the increase of both superficial gas velocity and the total specific power consumption.The quantitative correlations of NJSG,RPD andεGwere regressed as the function of superficial gas velocity,specific power consumption,Froude number and gas flow number,in order to provide the reference in the design of such three-phase stirred tank with similar multi-impellers.
