Despite the cubic system, the ability of sulphides to nucleate graphite can be enhanced by inoculating elements which transform them in complex compounds with a better lattice matching to graphite, a low coagulation c...Despite the cubic system, the ability of sulphides to nucleate graphite can be enhanced by inoculating elements which transform them in complex compounds with a better lattice matching to graphite, a low coagulation capacity, good stability and adequate interfacial energy. （Mn,X）S compounds, usually less than 5.0 μm in size, with an average 0.4-2.0 μm well defined core （nucleus）, were found to be important sites for graphite nucleation in grey irons. A three-stage model for the nucleation of graphite in grey irons is proposed： （1） Very small microinclusions based on strong deoxidizing elements （Mn, Si, Al, Ti, Zr） are formed in the melt; （2） Nucleation of complex （Mn,X）S compounds at these previously formed micro-inclusions; （3） Graphite nucleates on the sides of the （Mn,X）S compounds with lower crystallographic misfit. AI appears to have a key role in this process, as Al contributes to the formation of oxides in the first stage and favors the presence of Sr and Ca in the sulphides, in the second stage. The 0.005-0.010% Al range was found to be beneficial for lower undercooling solidification, type-A graphite formation and carbides avoidance.展开更多
Microstructure strongly influences the mechanical properties of cast iron. By inoculating the melt with proper inoculants, foreign substrates are brought into the melt and eventually the graphite can crystallize on th...Microstructure strongly influences the mechanical properties of cast iron. By inoculating the melt with proper inoculants, foreign substrates are brought into the melt and eventually the graphite can crystallize on them. The elements and substrates that really play a role for nucleation are yet unknown. Until now there is very little knowledge about the fundamentals of nucleation, such as composition and morphology of nuclei. In this work we utilized EN-GJL-200 as a base material and examined several produced specimens. The specimens were cast with and without inoculants and quenched at different solidification states. Specimens were also examined with a high and low oxygen concentration, but the results showed that different oxygen contents have no influence on the nucleation in cast iron melts. Our research was focused on the microscopic examination and phase-field simulations. For studying the samples we applied different analytical methods, where SEM-EDS, -WDS were proved to be most effective. The simulations were conducted by using the software MICRESS, which is based on a multiphase-field model and has been coupled directly to the TCFE3 thermodynamic database from TCAB. On the basis of the experimental investigations a nucleation mechanism is proposed, which claims MnS precipitates as the preferred site for graphite nucleation. This theory is supported by the results of the phase-field simulations.展开更多
The paper reviews original data obtained by the present authors,revealed in recent separate publications,describing specific procedures for high quality grey irons,and reflecting the forecast needs of the worldwide ir...The paper reviews original data obtained by the present authors,revealed in recent separate publications,describing specific procedures for high quality grey irons,and reflecting the forecast needs of the worldwide iron foundry industry.High power,medium frequency coreless induction furnaces are commonly used in electric melting grey iron foundries.This has resulted in low sulphur(<0.05wt.%)and aluminium(<0.005wt.%)contents in the iron,with a potential for higher superheating(>1,500°C),contributing to unfavourable conditions for graphite nucleation.Thin wall castings are increasingly produced by these electric melt shops with a risk of greater eutectic undercooling during solidification.The paper focused on two groups of grey cast irons and their specific problems:carbides and graphite morphology control in lower carbon equivalent high strength irons(CE=3.4%-3.8%),and austenite dendrite promotion in eutectic and slightly hypereutectic irons(CE=4.1%-4.5%),in order to increase their strength characteristics.There are 3 stages and 3 steps involving graphite formation,iron chemistry and iron processing that appear to be important.The concept in the present paper sustains a threestage model for nucleating flake graphite[(Mn,X)S type nuclei].There are three important groups of elements(deoxidizer,Mn/S,and inoculant)and three technological stages in electric melting of iron(superheat,pre-conditioning of base iron,final inoculation).Attention is drawn to a control factor(%Mn)x(%S)ensuring it equals to 0.03–0.06,accompanied by 0.005wt.%–0.010wt.%Al and/or Zr content in inoculated irons.It was found that iron powder addition promotes austenite dendrite formation in eutectic and slightly eutectic,acting as reinforcement for the eutectic cells.But,there is an accompanying possible negative influence on the characteristics of the(Mn,X)S type graphite nuclei(change the morphology of nuclei from polygonal compact to irregular polygonal,and therefore promote chill tendency in treated irons).A double addition(iron powder+inoculant)appears to be an effective treatment to benefit both austenite and graphite nucleation,with positive effects on the final structure and chill tendency.展开更多
文摘Despite the cubic system, the ability of sulphides to nucleate graphite can be enhanced by inoculating elements which transform them in complex compounds with a better lattice matching to graphite, a low coagulation capacity, good stability and adequate interfacial energy. （Mn,X）S compounds, usually less than 5.0 μm in size, with an average 0.4-2.0 μm well defined core （nucleus）, were found to be important sites for graphite nucleation in grey irons. A three-stage model for the nucleation of graphite in grey irons is proposed： （1） Very small microinclusions based on strong deoxidizing elements （Mn, Si, Al, Ti, Zr） are formed in the melt; （2） Nucleation of complex （Mn,X）S compounds at these previously formed micro-inclusions; （3） Graphite nucleates on the sides of the （Mn,X）S compounds with lower crystallographic misfit. AI appears to have a key role in this process, as Al contributes to the formation of oxides in the first stage and favors the presence of Sr and Ca in the sulphides, in the second stage. The 0.005-0.010% Al range was found to be beneficial for lower undercooling solidification, type-A graphite formation and carbides avoidance.
文摘Microstructure strongly influences the mechanical properties of cast iron. By inoculating the melt with proper inoculants, foreign substrates are brought into the melt and eventually the graphite can crystallize on them. The elements and substrates that really play a role for nucleation are yet unknown. Until now there is very little knowledge about the fundamentals of nucleation, such as composition and morphology of nuclei. In this work we utilized EN-GJL-200 as a base material and examined several produced specimens. The specimens were cast with and without inoculants and quenched at different solidification states. Specimens were also examined with a high and low oxygen concentration, but the results showed that different oxygen contents have no influence on the nucleation in cast iron melts. Our research was focused on the microscopic examination and phase-field simulations. For studying the samples we applied different analytical methods, where SEM-EDS, -WDS were proved to be most effective. The simulations were conducted by using the software MICRESS, which is based on a multiphase-field model and has been coupled directly to the TCFE3 thermodynamic database from TCAB. On the basis of the experimental investigations a nucleation mechanism is proposed, which claims MnS precipitates as the preferred site for graphite nucleation. This theory is supported by the results of the phase-field simulations.
文摘The paper reviews original data obtained by the present authors,revealed in recent separate publications,describing specific procedures for high quality grey irons,and reflecting the forecast needs of the worldwide iron foundry industry.High power,medium frequency coreless induction furnaces are commonly used in electric melting grey iron foundries.This has resulted in low sulphur(<0.05wt.%)and aluminium(<0.005wt.%)contents in the iron,with a potential for higher superheating(>1,500°C),contributing to unfavourable conditions for graphite nucleation.Thin wall castings are increasingly produced by these electric melt shops with a risk of greater eutectic undercooling during solidification.The paper focused on two groups of grey cast irons and their specific problems:carbides and graphite morphology control in lower carbon equivalent high strength irons(CE=3.4%-3.8%),and austenite dendrite promotion in eutectic and slightly hypereutectic irons(CE=4.1%-4.5%),in order to increase their strength characteristics.There are 3 stages and 3 steps involving graphite formation,iron chemistry and iron processing that appear to be important.The concept in the present paper sustains a threestage model for nucleating flake graphite[(Mn,X)S type nuclei].There are three important groups of elements(deoxidizer,Mn/S,and inoculant)and three technological stages in electric melting of iron(superheat,pre-conditioning of base iron,final inoculation).Attention is drawn to a control factor(%Mn)x(%S)ensuring it equals to 0.03–0.06,accompanied by 0.005wt.%–0.010wt.%Al and/or Zr content in inoculated irons.It was found that iron powder addition promotes austenite dendrite formation in eutectic and slightly eutectic,acting as reinforcement for the eutectic cells.But,there is an accompanying possible negative influence on the characteristics of the(Mn,X)S type graphite nuclei(change the morphology of nuclei from polygonal compact to irregular polygonal,and therefore promote chill tendency in treated irons).A double addition(iron powder+inoculant)appears to be an effective treatment to benefit both austenite and graphite nucleation,with positive effects on the final structure and chill tendency.
