AIM To evaluate the risk profile of sulfur hexafluoride in voiding urosonography(VUS) based on a large cohort of children.METHODS Since 2011 sulfur hexafluoride(SH,SonoV ue?,Bracco,Italy) is the only ultrasound contra...AIM To evaluate the risk profile of sulfur hexafluoride in voiding urosonography(VUS) based on a large cohort of children.METHODS Since 2011 sulfur hexafluoride(SH,SonoV ue?,Bracco,Italy) is the only ultrasound contrast available in the European Union and its use in children has not been approved.Within a 4-year-period,531 children with suspected or proven vesicoureteral reflux(f/m = 478/53; mean age 4.9 years; 1 mo-25.2 years) following parental informed consent underwent VUS with administration of 2.6 ± 1.2 mL SH in a two-center study.A standardizedtelephone survey on adverse events was conducted three days later.RESULTS No acute adverse reactions were observed.The survey revealed subacute,mostly self-limited adverse events in 4.1%(22/531).The majority of observed adverse events(17/22) was not suspected to be caused by an allergic reaction: Five were related to catheter placement,three to reactivated urinary tract infections,five were associated with perineal disinfection before voiding urosonography or perineal dermatitis and four with a common cold.In five patients(0.9%) hints to a potential allergic cause were noted: Perineal urticaria was reported in three interviews and isolated,mild fever in two.These were minor self-limited adverse events with a subacute onset and no hospital admittance was necessary.Ninety-six point two percent of the parents would prefer future VUS examinations with use of SH.CONCLUSION No severe adverse events were observed and indications of self-limited minor allergic reactions related to intravesical administration of SH were reported in less than 1%.展开更多
Photoacoustic spectroscopy was used to test the photoacoustic properties of sulfur hexafluoride, an optically thick and potent greenhouse gas. While exploring the photoacoustic effect of sulfur hexafluoride, the effec...Photoacoustic spectroscopy was used to test the photoacoustic properties of sulfur hexafluoride, an optically thick and potent greenhouse gas. While exploring the photoacoustic effect of sulfur hexafluoride, the effects of the position of the microphone within a gas cell were determined. Using a 35 cm gas cell, microphones were positioned at 17.5 cm, the middle of the gas cell, 12.5 cm, 7.5 cm, and 2.5 cm from the window of the cell. From the photoacoustic signal produced for each resonance frequency at each microphone position, the effects of acoustic pressure produced at each position on the signal recorded were observed. This is the first study done by experimentation with the photoacoustic effect to show that standing waves have different amplitudes at different microphone positions.展开更多
Sulfur hexafluoride(SF_(6))is an extremely severe greenhouse gas.It is an urgently important mission to find excellent candidates for selective adsorption of SF_(6),in order to reduce the emission of SF_(6) facilities...Sulfur hexafluoride(SF_(6))is an extremely severe greenhouse gas.It is an urgently important mission to find excellent candidates for selective adsorption of SF_(6),in order to reduce the emission of SF_(6) facilities.Here,we adopt the molecular simulation method to systematically explore the selective adsorption of SF_(6) in 22 kinds of representative covalent-and metal-organic frameworks.Results indicate that COF-6 is a promising candidate for the SF_(6) adsorption at low pressure P<20 kPa because of its small pore size,while MOF-180 and PAF-302 are excellent candidates at high pressure P=2×10^(3) kPa due to their large Brunauer-Emmett-Teller specific surface area(BET SSA)and pore volumes.For the two cases of the power industry(X_(SF_(6))=0.1)and the semiconductor industry(X_(SF_(6))=0.002)environments,COF-6 and ZIF-8 are fairly promising candidates for selective adsorption of SF_(6) from the SF_(6)/N_(2) mixtures,because they not only present the high selectivity,but also the large adsorption capacity at ambient environment,which can be considered as potential adsorbents for selective adsorption of SF_(6) at ambient conditions.展开更多
Abstract: In the occurrence of arc discharges, spark discharges, corona discharges and overheated faults in electrical equipment, SF 6would be decomposed to complicated byproducts, such as SO2 , H2S and HF. Analyzing ...Abstract: In the occurrence of arc discharges, spark discharges, corona discharges and overheated faults in electrical equipment, SF 6would be decomposed to complicated byproducts, such as SO2 , H2S and HF. Analyzing these byproducts is an effective method to judge the internal operation condition of electric equipment. In order to study characters of SF6byproducts at different temperature of overheated faults in the electric equipment, a series of overheated faults of electric equipment were simulated. SF6is very stable and not significantly decomposed at 200oC, 250oC and 300oC. SF6is significantly decomposed to SO2, H2S and HF at 350oC. The concentration of SO2, H2S and HF was 7.2, 1.6 and 1.9 μL/L after heating for 5 hours in environment of SF6with 3616 μL/L water, and it was increased to 23.0, 3.0 and 1.2 μL/L 3 hours later. SF6is more easily to be decomposed and decomposed more rapidly at higher temperature. The concentration of SO2, H2S and HF was 62.2, 15.6 and 3.6 μL/L after heating for 5 hours in environment of SF6with 4064 μL/L water, and it was increased to 91.4, 25.2 and 2.3 μL/L 3 hours later. SF6will be decomposed to format HF, which is strongly corrosive and whose concentration is likely to decrease when it is above a certain concentration.展开更多
In this research,plasma electrolytic oxidation coatings were prepared on AZ31 Mg alloy in a silicate-based solution containing K_(2)TiF_(6) using bipolar and soft sparking waveforms with 10,20,and 30%cathodic duty cyc...In this research,plasma electrolytic oxidation coatings were prepared on AZ31 Mg alloy in a silicate-based solution containing K_(2)TiF_(6) using bipolar and soft sparking waveforms with 10,20,and 30%cathodic duty cycles.The coatings displayed a net-like surface morphology consisted of irregular micro-pores,micro-cracks,fused oxide particles,and a sintered structure.Due to the incorporation of TiO_(2) colloidal particles and the cathodic pulse repair effect,most of the micro-pores were sealed.Long-term corrosion performance of the coatings was investigated using electrochemical impedance spectroscopy during immersion in 3.5 wt.%NaCl solution up to 14 days.The coating grown by the soft sparking waveform with a 20%cathodic duty cycle having the lowest porosity(6.2%)and a sharp layer concentrated in F element at the substrate/coating interface shows the highest corrosion resistance.The friction coefficient of this coating has remained stable during the sliding even under 5 N normal load,showing relatively higher wear resistance than other coatings.The coating produced using the equivalent unipolar waveform,as the reference specimen,showed the highest friction coefficient and the lowest wear resistance despite its highest micro-hardness.展开更多
In June, 2004 and February, 2007, in field tracer studies were conducted on the Hollywood and South Central outfalls, using sulfur hexafluoride (SF6) as a tracer. The objective of these studies was to determine if the...In June, 2004 and February, 2007, in field tracer studies were conducted on the Hollywood and South Central outfalls, using sulfur hexafluoride (SF6) as a tracer. The objective of these studies was to determine if the tracer could be detected in the farfield at significant distance, and if so, could this data be used to construct a model of the farfield plume. Prior models for farfield plume movement do not appear to comport well with the conditions in southeast Florida. Extensive research was conducted in southeast Florida on 4 outfalls, which led to the development of nearfield dilution equations for same. However farfield modeling of outfall plumes was difficult to accomplish because the tracers used are not detectable for significant distances. The SF6 resolved that problem and as a result the Hollywood outfall was used to construct a model. Two methods were investigated for modeling the plume, 1) the Eureqa formulation method and 2) the Gamma-Curve method. The concentrations in the x-y plane were first found by using the Eureqa formulation to calculate the concentration at each grid point given its depth and the concentration of the centerline at the same latitude. The plume models were generated using MATLAB that matched with the results actually seen in the field.展开更多
In a magnetized plasma column generated from an electronegative gas, negative-ions accumulate around the plasma column via radial diffusion. In this study, a dc discharge is applied in SF6 gas to produce a plasma colu...In a magnetized plasma column generated from an electronegative gas, negative-ions accumulate around the plasma column via radial diffusion. In this study, a dc discharge is applied in SF6 gas to produce a plasma column, and the radial density profile of negative-ions is measured by Langmuir probes using the modified Bohm criterion. The gas pressure and discharge current dependences of negative-ion density are also measured. It is found that the negative-ion density of 8.0 × 1017 m-3 is obtained around the plasma column at r = 1.0 cm when SF6 pressure is 0.13 Pa and discharge current is 0.50 A. The negative-ion density has radial gradient, and the electron density is much lower in this region.展开更多
Environment-friendly gas insulating mediums adapted to a DC gas-insulated transmission line(GIL)electric field condition is the key to the next generation of Environment-friendly HVDC GILs.In this paper,we review the ...Environment-friendly gas insulating mediums adapted to a DC gas-insulated transmission line(GIL)electric field condition is the key to the next generation of Environment-friendly HVDC GILs.In this paper,we review the literature on sulfur hexafluoride(SF6)alternatives including the scientific understanding,control,and implementation of gas-solid systems in this type of power transmission.First,the structure-activity relationship between the molecular structure and physico-chemical properties of Environment-friendly insulating gases is presented.Then,the search and prediction of important physicochemical properties of gases are summarized.Subsequently,in view of the potential of environmental friendly insulating gases,the swarm parameters of gas discharge and breakdown properties in a quasi-uniform field,inhomogeneous field,and at the gas-solid interface,that need to be taken into account with industrialized DC GILs are discussed.The latest research progress on insulation characteristics,especially the polarity effect in DC gas-solid insulation systems,the sensitivity to the electrode surface state,and the non-uniformity of the electric field,and the influence of metal particles and their variation with air pressure,is highlighted.In addition,the heat transfer characteristics of insulating gases,related to DC GIL transmission with a large current-carrying capacity and the influence of alternative gases on the heat transfer characteristics are described.Finally,aiming at solving the contradiction of low environmental impact,high dielectric strength and low liquefaction temperatures in the selection of alternative gases,an coordinated regulation model for Environment-friendly gases in DC GILs is established.Considerations for future work on this topic are also presented.展开更多
文摘AIM To evaluate the risk profile of sulfur hexafluoride in voiding urosonography(VUS) based on a large cohort of children.METHODS Since 2011 sulfur hexafluoride(SH,SonoV ue?,Bracco,Italy) is the only ultrasound contrast available in the European Union and its use in children has not been approved.Within a 4-year-period,531 children with suspected or proven vesicoureteral reflux(f/m = 478/53; mean age 4.9 years; 1 mo-25.2 years) following parental informed consent underwent VUS with administration of 2.6 ± 1.2 mL SH in a two-center study.A standardizedtelephone survey on adverse events was conducted three days later.RESULTS No acute adverse reactions were observed.The survey revealed subacute,mostly self-limited adverse events in 4.1%(22/531).The majority of observed adverse events(17/22) was not suspected to be caused by an allergic reaction: Five were related to catheter placement,three to reactivated urinary tract infections,five were associated with perineal disinfection before voiding urosonography or perineal dermatitis and four with a common cold.In five patients(0.9%) hints to a potential allergic cause were noted: Perineal urticaria was reported in three interviews and isolated,mild fever in two.These were minor self-limited adverse events with a subacute onset and no hospital admittance was necessary.Ninety-six point two percent of the parents would prefer future VUS examinations with use of SH.CONCLUSION No severe adverse events were observed and indications of self-limited minor allergic reactions related to intravesical administration of SH were reported in less than 1%.
文摘Photoacoustic spectroscopy was used to test the photoacoustic properties of sulfur hexafluoride, an optically thick and potent greenhouse gas. While exploring the photoacoustic effect of sulfur hexafluoride, the effects of the position of the microphone within a gas cell were determined. Using a 35 cm gas cell, microphones were positioned at 17.5 cm, the middle of the gas cell, 12.5 cm, 7.5 cm, and 2.5 cm from the window of the cell. From the photoacoustic signal produced for each resonance frequency at each microphone position, the effects of acoustic pressure produced at each position on the signal recorded were observed. This is the first study done by experimentation with the photoacoustic effect to show that standing waves have different amplitudes at different microphone positions.
基金We are greatly thankful to the support from the Open Fund of the State Key Laboratory of Laser Interaction with Matter(SKLLIM1710).
文摘Sulfur hexafluoride(SF_(6))is an extremely severe greenhouse gas.It is an urgently important mission to find excellent candidates for selective adsorption of SF_(6),in order to reduce the emission of SF_(6) facilities.Here,we adopt the molecular simulation method to systematically explore the selective adsorption of SF_(6) in 22 kinds of representative covalent-and metal-organic frameworks.Results indicate that COF-6 is a promising candidate for the SF_(6) adsorption at low pressure P<20 kPa because of its small pore size,while MOF-180 and PAF-302 are excellent candidates at high pressure P=2×10^(3) kPa due to their large Brunauer-Emmett-Teller specific surface area(BET SSA)and pore volumes.For the two cases of the power industry(X_(SF_(6))=0.1)and the semiconductor industry(X_(SF_(6))=0.002)environments,COF-6 and ZIF-8 are fairly promising candidates for selective adsorption of SF_(6) from the SF_(6)/N_(2) mixtures,because they not only present the high selectivity,but also the large adsorption capacity at ambient environment,which can be considered as potential adsorbents for selective adsorption of SF_(6) at ambient conditions.
文摘Abstract: In the occurrence of arc discharges, spark discharges, corona discharges and overheated faults in electrical equipment, SF 6would be decomposed to complicated byproducts, such as SO2 , H2S and HF. Analyzing these byproducts is an effective method to judge the internal operation condition of electric equipment. In order to study characters of SF6byproducts at different temperature of overheated faults in the electric equipment, a series of overheated faults of electric equipment were simulated. SF6is very stable and not significantly decomposed at 200oC, 250oC and 300oC. SF6is significantly decomposed to SO2, H2S and HF at 350oC. The concentration of SO2, H2S and HF was 7.2, 1.6 and 1.9 μL/L after heating for 5 hours in environment of SF6with 3616 μL/L water, and it was increased to 23.0, 3.0 and 1.2 μL/L 3 hours later. SF6is more easily to be decomposed and decomposed more rapidly at higher temperature. The concentration of SO2, H2S and HF was 62.2, 15.6 and 3.6 μL/L after heating for 5 hours in environment of SF6with 4064 μL/L water, and it was increased to 91.4, 25.2 and 2.3 μL/L 3 hours later. SF6will be decomposed to format HF, which is strongly corrosive and whose concentration is likely to decrease when it is above a certain concentration.
文摘In this research,plasma electrolytic oxidation coatings were prepared on AZ31 Mg alloy in a silicate-based solution containing K_(2)TiF_(6) using bipolar and soft sparking waveforms with 10,20,and 30%cathodic duty cycles.The coatings displayed a net-like surface morphology consisted of irregular micro-pores,micro-cracks,fused oxide particles,and a sintered structure.Due to the incorporation of TiO_(2) colloidal particles and the cathodic pulse repair effect,most of the micro-pores were sealed.Long-term corrosion performance of the coatings was investigated using electrochemical impedance spectroscopy during immersion in 3.5 wt.%NaCl solution up to 14 days.The coating grown by the soft sparking waveform with a 20%cathodic duty cycle having the lowest porosity(6.2%)and a sharp layer concentrated in F element at the substrate/coating interface shows the highest corrosion resistance.The friction coefficient of this coating has remained stable during the sliding even under 5 N normal load,showing relatively higher wear resistance than other coatings.The coating produced using the equivalent unipolar waveform,as the reference specimen,showed the highest friction coefficient and the lowest wear resistance despite its highest micro-hardness.
文摘In June, 2004 and February, 2007, in field tracer studies were conducted on the Hollywood and South Central outfalls, using sulfur hexafluoride (SF6) as a tracer. The objective of these studies was to determine if the tracer could be detected in the farfield at significant distance, and if so, could this data be used to construct a model of the farfield plume. Prior models for farfield plume movement do not appear to comport well with the conditions in southeast Florida. Extensive research was conducted in southeast Florida on 4 outfalls, which led to the development of nearfield dilution equations for same. However farfield modeling of outfall plumes was difficult to accomplish because the tracers used are not detectable for significant distances. The SF6 resolved that problem and as a result the Hollywood outfall was used to construct a model. Two methods were investigated for modeling the plume, 1) the Eureqa formulation method and 2) the Gamma-Curve method. The concentrations in the x-y plane were first found by using the Eureqa formulation to calculate the concentration at each grid point given its depth and the concentration of the centerline at the same latitude. The plume models were generated using MATLAB that matched with the results actually seen in the field.
文摘In a magnetized plasma column generated from an electronegative gas, negative-ions accumulate around the plasma column via radial diffusion. In this study, a dc discharge is applied in SF6 gas to produce a plasma column, and the radial density profile of negative-ions is measured by Langmuir probes using the modified Bohm criterion. The gas pressure and discharge current dependences of negative-ion density are also measured. It is found that the negative-ion density of 8.0 × 1017 m-3 is obtained around the plasma column at r = 1.0 cm when SF6 pressure is 0.13 Pa and discharge current is 0.50 A. The negative-ion density has radial gradient, and the electron density is much lower in this region.
基金This work was supported in part by the National Basic Research Program of China(973 Program)(2014CB239500).
文摘Environment-friendly gas insulating mediums adapted to a DC gas-insulated transmission line(GIL)electric field condition is the key to the next generation of Environment-friendly HVDC GILs.In this paper,we review the literature on sulfur hexafluoride(SF6)alternatives including the scientific understanding,control,and implementation of gas-solid systems in this type of power transmission.First,the structure-activity relationship between the molecular structure and physico-chemical properties of Environment-friendly insulating gases is presented.Then,the search and prediction of important physicochemical properties of gases are summarized.Subsequently,in view of the potential of environmental friendly insulating gases,the swarm parameters of gas discharge and breakdown properties in a quasi-uniform field,inhomogeneous field,and at the gas-solid interface,that need to be taken into account with industrialized DC GILs are discussed.The latest research progress on insulation characteristics,especially the polarity effect in DC gas-solid insulation systems,the sensitivity to the electrode surface state,and the non-uniformity of the electric field,and the influence of metal particles and their variation with air pressure,is highlighted.In addition,the heat transfer characteristics of insulating gases,related to DC GIL transmission with a large current-carrying capacity and the influence of alternative gases on the heat transfer characteristics are described.Finally,aiming at solving the contradiction of low environmental impact,high dielectric strength and low liquefaction temperatures in the selection of alternative gases,an coordinated regulation model for Environment-friendly gases in DC GILs is established.Considerations for future work on this topic are also presented.
