High-temperature treatment is key to the preparation of zeolite catalysts.Herein,the effects of hightemperature treatment on the property and performance of HZSM-5 zeolites were studied in this work.X-Ray diffraction,...High-temperature treatment is key to the preparation of zeolite catalysts.Herein,the effects of hightemperature treatment on the property and performance of HZSM-5 zeolites were studied in this work.X-Ray diffraction,N2physisorption,27Al magic angle spinning nuclear magnetic resonance(MAS NMR),and temperature-programmed desorption of ammonia results indicated that the hightemperature treatment at 650℃ hardly affected the inherent crystal and texture of HZSM-5zeolites but facilitated the conversion of framework Al to extra-framework Al,reducing the acid site and enhancing the acid strength.Moreover,the high-temperature treatment improved the performance of HZSM-5 zeolites in n-heptane catalytic cracking,promoting the conversion and light olefins yield while inhibiting coke formation.Based on the kinetic and mechanism analysis,the improvement of HZSM-5 performance caused by high-temperature treatment has been attributed to the formation of extra-framework Al,which enhanced the acid strength,facilitated the bimolecular reaction,and promoted the entropy change to overcome a higher energy barrier in n-heptane catalytic cracking.展开更多
This study focuses on finding a solution to the sharp decline in mechanical properties of Al-Si-Cu-Mg alloys due to rapid coarsening of traditional intermediate phases at high temperature.A new type of modified al oy,...This study focuses on finding a solution to the sharp decline in mechanical properties of Al-Si-Cu-Mg alloys due to rapid coarsening of traditional intermediate phases at high temperature.A new type of modified al oy,to be used in automobile engines at high temperatures,was prepared by adding Zr and Mo into Al-Si-Cu-Mg alloy.The synergistic effects of Zr and Mo on the microstructure evolution and high-temperature mechanical properties were studied.Results show that the addition of Zr and Mo generates a series of intermetallic phases dispersed in the alloy.They can improve the strength of the alloy by hindering dislocation movement and crack propagation.In addition,some nano-strengthened phases show coherent interfaces with the matrix and improve grain refinement.The addition of Mo greatly improves the heat resistance of the alloy.The extremely low diffusivity of Mo enables it to improve the thermal stability of the intermetallic phases,inhibit precipitation during aging,reduce the size of the precipitates,and improve the heat resistance of the alloy.展开更多
Aviation turbine engine oils require excellent thermal-oxidative stability because of their high-temperature environments.High-temperature bearing deposit testing is a mandatory method for measuring the thermal-oxidat...Aviation turbine engine oils require excellent thermal-oxidative stability because of their high-temperature environments.High-temperature bearing deposit testing is a mandatory method for measuring the thermal-oxidative performance of aviation lubricant oils,and the relevant apparatus was improved in the present study.Two different commercial aviation turbine engine oils were tested,one with standard performance(known as the SL oil)and the other with high thermal stability,and their thermal-oxidative stability characteristics were evaluated.After 100 h of high-temperature bearing testing,the SL oil was analyzed by using various analytical techniques to investigate its thermal-oxidative process in the bearing test,with its thermal-oxidative degradation mechanism also being discussed.The results indicate that the developed high-temperature bearing apparatus easily meets the test requirements of method 3410.1 in standard FED-STD-791D.The viscosity and total acid number(TAN)of the SL oil increased with the bearing test time,and various deposits were produced in the bearing test,with the micro-particles of the carbon deposits being sphere-like,rod-like,and sheet-like in appearance.The antioxidant additives in the oil were consumed very rapidly in the first 30 h of the bearing test,with N-phenyl-1-naphthylamine being consumed faster than dioctyldiphenylamine.Overall,the oil thermal-oxidative process involves very complex physical and chemical mechanisms.展开更多
Cotton(Gossypium spp.) yield is reduced by stress. In this study, high temperature(HT) suppressed the expression of the jasmonic acid(JA) biosynthesis gene allene oxide cyclase 2(GhAOC2), reducing JA content and causi...Cotton(Gossypium spp.) yield is reduced by stress. In this study, high temperature(HT) suppressed the expression of the jasmonic acid(JA) biosynthesis gene allene oxide cyclase 2(GhAOC2), reducing JA content and causing male sterility in the cotton HT-sensitive line H05. Anther sterility was reversed by exogenous application of methyl jasmonate(MeJA) to early buds. To elucidate the role of GhAOC2 in JA biosynthesis and identify its putative contribution to the anther response to HT, we created gene knockout cotton plants using the CRISPR/Cas9 system. Ghaoc2 mutant lines showed male-sterile flowers with reduced JA content in the anthers at the tetrad stage(TS), tapetum degradation stage(TDS), and anther dehiscence stage(ADS). Exogenous application of MeJA to early mutant buds(containing TS or TDS anthers) rescued the sterile pollen and indehiscent anther phenotypes, while ROS signals were reduced in ADS anthers. We propose that HT downregulates the expression of GhAOC2 in anthers, reducing JA biosynthesis and causing excessive ROS accumulation in anthers, leading to male sterility. These findings suggest exogenous JA application as a strategy for increasing male fertility in cotton under HT.展开更多
Extreme high temperatures frequently occur in southwestern China,significantly impacting the local ecological system and economic development.However,accurate prediction of extreme high-temperature days(EHDs)in this r...Extreme high temperatures frequently occur in southwestern China,significantly impacting the local ecological system and economic development.However,accurate prediction of extreme high-temperature days(EHDs)in this region is still an unresolved challenge.Based on the spatiotemporal characteristics of EHDs over China,a domain-averaged EHD index over southwestern China(SWC-EHDs)during April-May is defined.The simultaneous dynamic and thermodynamic fields associated with the increased SWC-EHDs are a local upper-level anticyclonic(high-pressure)anomaly and wavy geopotential height anomaly patterns over Eurasia.In tracing the origins of the lower boundary anomalies,two physically meaningful precursors are detected for SWC-EHDs.They are the tripolar SST change tendency from December-January to February-March in the northern Atlantic and the February-March mean snow depth in central Asia.Using these two selected predictors,a physics-based empirical model prediction was applied to the training period of 1961–2005 to obtain a skillful prediction of the EHDs index,attaining a correlation coefficient of 0.76 in the independent prediction period(2006–19),suggesting that 58%of the total SWC-EHDs variability is predictable.This study provides an estimate for the lower bound of the seasonal predictability of EHDs as well as for the hydrological drought over southwestern China.展开更多
Nanoparticles have been widely used in polymer gel systems in recent years to improve gelation performance under high-temperature reservoir conditions. However, different types of nanoparticles have different effects ...Nanoparticles have been widely used in polymer gel systems in recent years to improve gelation performance under high-temperature reservoir conditions. However, different types of nanoparticles have different effects on their gelation performance, which has been little researched. In this study, the high-temperature gelation performance, chemical structure, and microstructure of polymer gels prepared from two nanomaterials (i.e., nano-SiO_(2) and nano-TiO_(2)) were measured. The conventional HPAM/PEI polymer gel system was employed as the control sample. Results showed that the addition of nano-TiO_(2) could significantly enhance the gel strength of HPAM/PEI gel at 80 ℃. The gel strength of the enhanced HPAM/PEI gel with 0.1 wt% nano-TiO_(2) could reach grade I. The system also had excellent high-temperature stability at 150 ℃. The enhanced HPAM/PEI gel with 0.02 wt% nano-TiO_(2) reached the maximum gel strength at 150 ℃ with a storage modulus (G′) of 15 Pa, which can meet the need for efficient plugging. However, the nano-SiO_(2) enhanced HPAM/PEI polymer gel system showed weaker gel strength than that with nano-TiO_(2) at both 80 and 150 ℃ with G′ lower than 5 Pa. Microstructures showed that the nano-TiO_(2) enhanced HPAM/PEI gel had denser three-dimensional (3D) mesh structures, which makes the nano-TiO_(2) enhanced HPAM/PEI gel more firmly bound to water. The FT-IR results also confirmed that the chemical structure of the nano-TiO_(2) enhanced HPAM/PEI gel was more thermally stable than nano-SiO_(2) since there was a large amount of –OH groups on the structure surface. Therefore, nano-TiO_(2) was more suitable as the reinforcing material for HPAM/PEI gels for high-temperature petroleum reservoir conformance improvement.展开更多
In order to evaluate the feasibility of steel slag powder as filler,the coating properties of steel slag and limestone aggregate were compared by water boiling test,the micro morphology difierences between steel slag ...In order to evaluate the feasibility of steel slag powder as filler,the coating properties of steel slag and limestone aggregate were compared by water boiling test,the micro morphology difierences between steel slag powder and mineral powder(limestone powder)were compared by scanning electron microscope(SEM),and the high-temperature rheological properties of asphalt mortar with difierent ratio of filler quality to asphalt quality(F/A)and difierent substitution rates of mineral powder(S/F)were studied by dynamic shear rheological test.The results show that the surface microstructure of steel slag powder is more abundant than that of mineral powder,and the adhesion of steel slag to asphalt is better than that of limestone.At the same temperature,the lower the ratio of S/F is,the greater the rutting factor and complex modulus will be.In addition,the complex modulus and rutting factor of the asphalt mortar increase with the increase of F/A,and the filler type and F/A have a negligible efiect on the phase angle.展开更多
Embracing ultrahigh theoretical capacity of 3860 mA h g^(-1)and the lowest reduction potential of-3.04 V(versus standard hydrogen electrode),lithium(Li) is considered as the "holy grail" material for pursuin...Embracing ultrahigh theoretical capacity of 3860 mA h g^(-1)and the lowest reduction potential of-3.04 V(versus standard hydrogen electrode),lithium(Li) is considered as the "holy grail" material for pursuing higher energy density,of which application has been challenged due to the unstable interface caused by the non-uniform electrodeposition as well as high chemical activity.Operating at higher temperature can be recommended to uniform electrodeposition of Li metal.Nevertheless,the intrinsic side-reaction between Li metal anode and electrolyte is inevitably aggravated and thus fosters the failure of Li metal anode rapidly with uneven electrodeposition.Here,a kind of temperature-tolerated ionic liquid(1-methyl-3-ethylimidazole bis(fluorosulfo nyl)imide/lithium bis(trifluoromethylsulfo nyl)imide,EF/LT)based electrolyte that matrixed with poly(vinylidene fluoride-hexafluoropropylene) was designed to maintain the interfacial stabilization of Li metal due to the weak interfacial reaction and uniform electrodeposition at high temperature of 80℃.It is the matter that the 660-h cycle with lower polarization is achieved with EF/LT-based electrolyte at temperature of 80 ℃ and the full cell embraces outstanding cyclic performance,without capacity fading within 100 cycles.Delighting,a door for practical application of Li metal anode for higher energy density as the carbon neutrality progresses in the blooming human society has been opened gradually.展开更多
Understanding the thermal safety evolution of lithium-ion batteries during high-temperature usage conditions bears significant implications for enhancing the safety management of aging batteries.This work investigates...Understanding the thermal safety evolution of lithium-ion batteries during high-temperature usage conditions bears significant implications for enhancing the safety management of aging batteries.This work investigates the thermal safety evolution mechanism of lithium-ion batteries during high-temperature aging.Similarities arise in the thermal safety evolution and degradation mechanisms for lithium-ion batteries undergoing cyclic aging and calendar aging.Employing multi-angle characterization analysis,the intricate mechanism governing the thermal safety evolution of lithium-ion batteries during high-temperature aging is clarified.Specifically,lithium plating serves as the pivotal factor contributing to the reduction in the self-heating initial temperature.Additionally,the crystal structure of the cathode induced by the dissolution of transition metals and the reductive gas generated during aging attacking the crystal structure of the cathode lead to a decrease in thermal runaway triggering temperature.Furthermore,the loss of active materials and active lithium during aging contributes to a decline in both the maximum temperature and the maximum temperature rise rate,ultimately indicating a decrease in the thermal hazards of aging batteries.展开更多
The composites were prepared by modifying silicon carbide fiber with particles of zirconium carbide(ZrC)and boron carbide(B_(4)C)and incorporating them into a phenolic resin matrix.The influence of ZrC and B_(4)C on t...The composites were prepared by modifying silicon carbide fiber with particles of zirconium carbide(ZrC)and boron carbide(B_(4)C)and incorporating them into a phenolic resin matrix.The influence of ZrC and B_(4)C on the mechanical performance of SiCf/phenolic composites after high-temperature pyrolysis was studied through flexural performance test.The results show that the composite material has good thermal stability and high-temperature mechanical properties.After static ablation at 1400℃ for 15 minutes,the flexural strength of the composite material reaches 286 MPa,which is still 7.3%higher than at room temperature,indicating that the composite material still has good mechanical properties even after heat treatment at 1400℃.展开更多
Photonic crystal structures have excellent optical properties,so they are widely studied in conventional optical materials.Recent research shows that high-temperature superconducting periodic structures have natural p...Photonic crystal structures have excellent optical properties,so they are widely studied in conventional optical materials.Recent research shows that high-temperature superconducting periodic structures have natural photonic crystal features and they are favourable candidates for single-photon detection.Considering that superconductors have completely different properties from conventional optical materials,we study the energy level diagram and mid-infrared 3μm–5μm transmission spectrum of two-dimensional superconducting photonic crystals in both superconducting and quenched states with the finite element method.The energy level diagram of the circular crystal column superconducting structure shows that the structure has a large band gap width in both states.At the same fill factor,the circular crystal column superconducting structure has a larger band gap width than the others structures.For lattice structures,the zero transmission point of the square lattice structure is robust to the incident angle and environmental temperature.Our research has guiding significance for the design of new material photonic crystals,photon modulation and detection.展开更多
The high-temperature molten salt pump is the core equipment in a molten salt reactor that drives the flow of the molten salt coolant.Rotor stability is key to the continuous and reliable operation of the molten salt p...The high-temperature molten salt pump is the core equipment in a molten salt reactor that drives the flow of the molten salt coolant.Rotor stability is key to the continuous and reliable operation of the molten salt pump,and the liquid seal at the wear ring can affect the dynamic characteristics of the rotor system.When the molten salt pump is operated in the hightemperature molten salt medium,thermal deformation of the submerged parts inevitably occurs,changing clearance between the stator and rotor,affecting the leakage and dynamic characteristics of the seal.In this study,the seal leakage,seal dynamic characteristics,and rotor system dynamic characteristics are simulated and analyzed using finite element simulation software based on two cases of considering the effect of seal thermal deformation effect or not.The results show a significant difference in the leakage characteristics and dynamic characteristics of the seal obtained by considering the effect of seal thermal deformation and neglecting the effect of thermal deformation.The leakage flow rate decreases,and the first-order critical speed of the seal-bearing-rotor system decrease after considering the seal’s thermal deformation.展开更多
Satellited CoNiCrAlY–Al_(2)O_(3)feedstocks with 2wt%, 4wt%, and 6wt% oxide nanoparticles and pure CoNiCrAlY powder were deposited by the high-velocity oxy fuel process on an Inconel738 superalloy substrate. The oxida...Satellited CoNiCrAlY–Al_(2)O_(3)feedstocks with 2wt%, 4wt%, and 6wt% oxide nanoparticles and pure CoNiCrAlY powder were deposited by the high-velocity oxy fuel process on an Inconel738 superalloy substrate. The oxidation test was performed at 1050℃ for 5, 50, 100,150, 200, and 400 h. The microstructure and phase composition of powders and coatings were characterized by scanning electron microscopy and X-ray diffraction, respectively. The bonding strength of the coatings was also evaluated. The results proved that with the increase in the percentage of nanoparticles(from 2wt% to 6wt%), the amount of porosity(from 1vol% to 4.7vol%), unmelted particles, and roughness of the coatings(from 4.8 to 8.8 μm) increased, and the bonding strength decreased from 71 to 48 MPa. The thicknesses of the thermally grown oxide layer of pure and composite coatings(2wt%, 4wt%, and 6wt%) after 400 h oxidation were measured as 6.5, 5.5, 7.6, and 8.1 μm, respectively.The CoNiCrAlY–2wt% Al_(2)O_(3)coating showed the highest oxidation resistance due to the diffusion barrier effect of well-dispersed nanoparticles. The CoNiCrAlY–6wt% Al_(2)O_(3)coating had the lowest oxidation resistance due to its rough surface morphology and porous microstructure.展开更多
Three high-temperature resistant polymeric additives for water-based drilling fluids are designed and developed:weakly cross-linked zwitterionic polymer fluid loss reducer(WCZ),flexible polymer microsphere nano-pluggi...Three high-temperature resistant polymeric additives for water-based drilling fluids are designed and developed:weakly cross-linked zwitterionic polymer fluid loss reducer(WCZ),flexible polymer microsphere nano-plugging agent(FPM)and comb-structure polymeric lubricant(CSP).A high-temperature resistant and high-density polymeric saturated brine-based drilling fluid was developed for deep drilling.The WCZ has a good anti-polyelectrolyte effect and exhibits the API fluid loss less than 8 mL after aging in saturated salt environment at 200°C.The FPM can reduce the fluid loss by improving the quality of the mud cake and has a good plugging effect on nano-scale pores/fractures.The CSP,with a weight average molecular weight of 4804,has multiple polar adsorption sites and exhibits excellent lubricating performance under high temperature and high salt conditions.The developed drilling fluid system with a density of 2.0 g/cm^(3)has good rheological properties.It shows a fluid loss less than 15 mL at 200°C and high pressure,a sedimentation factor(SF)smaller than 0.52 after standing at high temperature for 5 d,and a rolling recovery of hydratable drill cuttings similar to oil-based drilling fluid.Besides,it has good plugging and lubricating performance.展开更多
The doping of functionalized graphene oxide(GO)in the membranes becomes a promising method for improving the performance of high-temperature proton exchange membrane fuel cells(HT-PEMFC).Phosphonated graphene oxide(PG...The doping of functionalized graphene oxide(GO)in the membranes becomes a promising method for improving the performance of high-temperature proton exchange membrane fuel cells(HT-PEMFC).Phosphonated graphene oxide(PGO)with a P/O ratio of 8.5%was quickly synthesised by one-step electrochemical exfoliation based on a three-dimensiaonal(3D)printed reactor and natural graphite flakes.Compared with the GO prepared by the two-step electrochemical exfoliation method,the PGO synthesized by the one-step electrochemical exfoliation can better improve the performance of the membrane-electrode-assembly(MEA)based on the polybenzimidazole(PBI)membrane in the HTPEMFC.The doping of 1.5 wt%GO synthesised by electrochemical exfoliation with the 2-step method or reactor method in PBI increased the peak power density by 17.4%or 35.4%compared to MEA based on pure PBI membrane at 150℃,respectively.In addition,the doping of PGO in PBI improves its durability under accelerated stress test(AST).展开更多
Tree peony(Paeonia suffruticosa Andr.)is a traditional Chinese flower,which prefers cool weather.However,high temperature in summer in the middle and lower reaches of the Yangtze River restricts its growth and develop...Tree peony(Paeonia suffruticosa Andr.)is a traditional Chinese flower,which prefers cool weather.However,high temperature in summer in the middle and lower reaches of the Yangtze River restricts its growth and development.In this study,osmotic regulation,antioxidant enzyme activities,and photosynthetic characteristics of tree peony in response to high-temperature stress were investigated.The results showed that high-temperature stress had destroyed the cell membrane,manifested as the increased relative electrical conductivity and malondialdehyde content.Moreover,high-temperature stress led to excessive accumulation of reactive oxygen species,thereby,activating antioxidant enzyme activities.Also,photosynthetic parameters and chlorophyll fluorescence parameters directly reflected the damage to the photosystem II reflection center under high-temperature stress.In addition,high-temperature stress led to stomatal closure and chloroplast damage.This study revealed the physiological responses of tree peony to high-temperature stress,laying a foundation for the promotion of tree peony in high-temperature areas and the improvement of high-temperature resistance.展开更多
The traditional nano-sintering or TLP techniques are generally expensive,time-consuming,and hence unsuitable for realizing practical mass production.Herein,we have developed an improved TLP process to rapidly produce ...The traditional nano-sintering or TLP techniques are generally expensive,time-consuming,and hence unsuitable for realizing practical mass production.Herein,we have developed an improved TLP process to rapidly produce IMC-skeleton structures across the bonding region by initiating a localized liquid-solid interaction among micron particles at traditional soldering temperatures.The developed IMC skeletons can reinforce solder alloys and provide remarkable mechanical stability and electrical capabilities at high temperatures.As a result,the IMC-skeleton strengthened interconnections exhibited higher thermal/electrical conductivity,lower hardness and almost doubled strength than traditional full-IMC joints,attaining 87.4 MPa and 30.2 MPa at room condition and 350℃.Meanwhile,the necessary heating time to form metallurgical bonds was shortened,one-fifth of nano-sintering and one-tenth of TLP bonding,and the material cost was significantly reduced.This proposed technique enabled the fast,low-cost manufacturing of electronics that can serve at temperatures as high as 200−350℃.Besides,the interfacial reactions among particles and the correlated phase evolution process were studied in this research.The formation mechanism of IMC skeletons was analyzed.The correlated influencing factors and their effect on the mechanical,thermal and electrical properties of joints were revealed,which may help the design and extensive uses of such techniques in various high-temperature/power applications.展开更多
Process heating constitutes a significant share of final energy consumption in the industrial sector around the world.In this paper,a high-temperature heat pump(HTHP)using flash tank vapor injection technology(FTVI)is...Process heating constitutes a significant share of final energy consumption in the industrial sector around the world.In this paper,a high-temperature heat pump(HTHP)using flash tank vapor injection technology(FTVI)is proposed to develop low-temperature geothermal source for industrial process heating with temperature above 100°C.With heat sink output temperatures between 120°C and 150°C,the thermo-economic performance of the FTVI HTHP system using R1234ze(Z)as refrigerant is analyzed and also compared to the single-stage vapor compression(SSVC)system by employing the developed mathematical model.The coefficient of performance(COP),exergy efficiency(ηexe),net present value(NPV)and payback period(PBP)are used as performance indicators.The results show that under the typical working conditions,the COP andηexe of FTVI HTHP system are 3.00 and 59.66%,respectively,and the corresponding NPV and PBP reach 8.13×106 CNY and 4.13 years,respectively.Under the high-temperature heating conditions,the thermo-economic performance of the FTVI HTHP system is significantly better than that of the SSVC system,and the larger the temperature lift,the greater the thermo-economic advantage of the FTVI HTHP system.Additionally,the FTVI HTHP system is more capable than the SSVC system in absorbing the financial risks associated with changes of electricity price and natural gas price.展开更多
After the first concrete was poured on December 9,2012 at the Shidao Bay site in Rongcheng,Shandong Province,China,the construction of the reactor building for the world’s first high-temperature gascooled reactor peb...After the first concrete was poured on December 9,2012 at the Shidao Bay site in Rongcheng,Shandong Province,China,the construction of the reactor building for the world’s first high-temperature gascooled reactor pebble-bed module(HTR-PM)demonstration power plant was completed in June,2015.Installation of the main equipment then began,and the power plant is currently progressing well toward connecting to the grid at the end of 2017.The thermal power of a single HTR-PM reactor module is 250 MWth,the helium temperatures at the reactor core inlet/outlet are 250/750℃,and a steam of 13.25 MPa/567℃ is produced at the steam generator outlet.Two HTR-PM reactor modules are connected to a steam turbine to form a 210 MWe nuclear power plant.Due to China’s industrial capability,we were able to overcome great difficulties,manufacture first-of-a-kind equipment,and realize series major technological innovations.We have achieved successful results in many aspects,including planning and implementing R&D,establishing an industrial partnership,manufacturing equipment,fuel production,licensing,site preparation,and balancing safety and economics;these obtained experiences may also be referenced by the global nuclear community.展开更多
To solve the problem of the severe mismatch between the product and roll materials in the preliminary rolling line,a new graphitic steel material was designed,its microstructure and high-temperature friction and wear ...To solve the problem of the severe mismatch between the product and roll materials in the preliminary rolling line,a new graphitic steel material was designed,its microstructure and high-temperature friction and wear properties were investigated.Moreover,the feasibility of replacing semi-steel with this new material in the V1 stand roll was studied herein.The results show that the graphitic steel matrix is strengthened by silicon and nickel elements.The presence of spherical graphite also provides self-lubrication and heat conduction and prevents the propagation of cracks.Carbides in the appropriate amount and size strengthen the matrix,reduce the cracking effect of the matrix,and are not easily broken,thereby reducing high-temperature abrasive wear.Under the same hightemperature friction and wear conditions,compared with semi-steel,the wear-scar surface of graphitic steel exhibits less wear-scar depth and wear volume,a smaller friction coefficient,reduced oxide layer thickness,and fewer instances of peeling and microcracks.Therefore,the newly designed graphitic steel has higher wear resistance and hot-crack resistance than semi-steel,which makes it feasible for use in replacing semi-steel as a new V1 frame roll material in the blooming mill.展开更多
基金the financial support from the National Natural Science Foundation of China(21908010)Jilin Provincial Department of Science and Technology(20220101089JC)the Education Department of Jilin Province(JJKH20220694KJ)。
文摘High-temperature treatment is key to the preparation of zeolite catalysts.Herein,the effects of hightemperature treatment on the property and performance of HZSM-5 zeolites were studied in this work.X-Ray diffraction,N2physisorption,27Al magic angle spinning nuclear magnetic resonance(MAS NMR),and temperature-programmed desorption of ammonia results indicated that the hightemperature treatment at 650℃ hardly affected the inherent crystal and texture of HZSM-5zeolites but facilitated the conversion of framework Al to extra-framework Al,reducing the acid site and enhancing the acid strength.Moreover,the high-temperature treatment improved the performance of HZSM-5 zeolites in n-heptane catalytic cracking,promoting the conversion and light olefins yield while inhibiting coke formation.Based on the kinetic and mechanism analysis,the improvement of HZSM-5 performance caused by high-temperature treatment has been attributed to the formation of extra-framework Al,which enhanced the acid strength,facilitated the bimolecular reaction,and promoted the entropy change to overcome a higher energy barrier in n-heptane catalytic cracking.
基金supported by the Key R&D Program of Shandong Province of China(Grant number 2019QYTPY057)the Natural Science Foundation of Shandong Province of China(Grant numbers ZR2020ME110,ZR2021ME023)。
文摘This study focuses on finding a solution to the sharp decline in mechanical properties of Al-Si-Cu-Mg alloys due to rapid coarsening of traditional intermediate phases at high temperature.A new type of modified al oy,to be used in automobile engines at high temperatures,was prepared by adding Zr and Mo into Al-Si-Cu-Mg alloy.The synergistic effects of Zr and Mo on the microstructure evolution and high-temperature mechanical properties were studied.Results show that the addition of Zr and Mo generates a series of intermetallic phases dispersed in the alloy.They can improve the strength of the alloy by hindering dislocation movement and crack propagation.In addition,some nano-strengthened phases show coherent interfaces with the matrix and improve grain refinement.The addition of Mo greatly improves the heat resistance of the alloy.The extremely low diffusivity of Mo enables it to improve the thermal stability of the intermetallic phases,inhibit precipitation during aging,reduce the size of the precipitates,and improve the heat resistance of the alloy.
基金supported by the National Key Research and Development Program of China(2022YFB3809005)by SINOPEC(120060-6,121027,and 122042).
文摘Aviation turbine engine oils require excellent thermal-oxidative stability because of their high-temperature environments.High-temperature bearing deposit testing is a mandatory method for measuring the thermal-oxidative performance of aviation lubricant oils,and the relevant apparatus was improved in the present study.Two different commercial aviation turbine engine oils were tested,one with standard performance(known as the SL oil)and the other with high thermal stability,and their thermal-oxidative stability characteristics were evaluated.After 100 h of high-temperature bearing testing,the SL oil was analyzed by using various analytical techniques to investigate its thermal-oxidative process in the bearing test,with its thermal-oxidative degradation mechanism also being discussed.The results indicate that the developed high-temperature bearing apparatus easily meets the test requirements of method 3410.1 in standard FED-STD-791D.The viscosity and total acid number(TAN)of the SL oil increased with the bearing test time,and various deposits were produced in the bearing test,with the micro-particles of the carbon deposits being sphere-like,rod-like,and sheet-like in appearance.The antioxidant additives in the oil were consumed very rapidly in the first 30 h of the bearing test,with N-phenyl-1-naphthylamine being consumed faster than dioctyldiphenylamine.Overall,the oil thermal-oxidative process involves very complex physical and chemical mechanisms.
基金funding support from the National Natural Science Foundation of China (32072024)the Fundamental Research Funds for the Central Universities (2021ZKPY019)the National Key Research and Development Program of China (2018YFD0100403, 2016YFD0101402)。
文摘Cotton(Gossypium spp.) yield is reduced by stress. In this study, high temperature(HT) suppressed the expression of the jasmonic acid(JA) biosynthesis gene allene oxide cyclase 2(GhAOC2), reducing JA content and causing male sterility in the cotton HT-sensitive line H05. Anther sterility was reversed by exogenous application of methyl jasmonate(MeJA) to early buds. To elucidate the role of GhAOC2 in JA biosynthesis and identify its putative contribution to the anther response to HT, we created gene knockout cotton plants using the CRISPR/Cas9 system. Ghaoc2 mutant lines showed male-sterile flowers with reduced JA content in the anthers at the tetrad stage(TS), tapetum degradation stage(TDS), and anther dehiscence stage(ADS). Exogenous application of MeJA to early mutant buds(containing TS or TDS anthers) rescued the sterile pollen and indehiscent anther phenotypes, while ROS signals were reduced in ADS anthers. We propose that HT downregulates the expression of GhAOC2 in anthers, reducing JA biosynthesis and causing excessive ROS accumulation in anthers, leading to male sterility. These findings suggest exogenous JA application as a strategy for increasing male fertility in cotton under HT.
基金supported by the National Natural Science Foundation of China(Grant Nos.42088101 and 42175033)the High-Performance Computing Center of Nanjing University of Information Science&Technology。
文摘Extreme high temperatures frequently occur in southwestern China,significantly impacting the local ecological system and economic development.However,accurate prediction of extreme high-temperature days(EHDs)in this region is still an unresolved challenge.Based on the spatiotemporal characteristics of EHDs over China,a domain-averaged EHD index over southwestern China(SWC-EHDs)during April-May is defined.The simultaneous dynamic and thermodynamic fields associated with the increased SWC-EHDs are a local upper-level anticyclonic(high-pressure)anomaly and wavy geopotential height anomaly patterns over Eurasia.In tracing the origins of the lower boundary anomalies,two physically meaningful precursors are detected for SWC-EHDs.They are the tripolar SST change tendency from December-January to February-March in the northern Atlantic and the February-March mean snow depth in central Asia.Using these two selected predictors,a physics-based empirical model prediction was applied to the training period of 1961–2005 to obtain a skillful prediction of the EHDs index,attaining a correlation coefficient of 0.76 in the independent prediction period(2006–19),suggesting that 58%of the total SWC-EHDs variability is predictable.This study provides an estimate for the lower bound of the seasonal predictability of EHDs as well as for the hydrological drought over southwestern China.
基金supported by the Natural Science Foundation of Xinjiang Uygur Autonomous Region(No.2022D01A250)the CNPC Strategic Cooperation Science and Technology Project(ZLZX2020-01-04-04).
文摘Nanoparticles have been widely used in polymer gel systems in recent years to improve gelation performance under high-temperature reservoir conditions. However, different types of nanoparticles have different effects on their gelation performance, which has been little researched. In this study, the high-temperature gelation performance, chemical structure, and microstructure of polymer gels prepared from two nanomaterials (i.e., nano-SiO_(2) and nano-TiO_(2)) were measured. The conventional HPAM/PEI polymer gel system was employed as the control sample. Results showed that the addition of nano-TiO_(2) could significantly enhance the gel strength of HPAM/PEI gel at 80 ℃. The gel strength of the enhanced HPAM/PEI gel with 0.1 wt% nano-TiO_(2) could reach grade I. The system also had excellent high-temperature stability at 150 ℃. The enhanced HPAM/PEI gel with 0.02 wt% nano-TiO_(2) reached the maximum gel strength at 150 ℃ with a storage modulus (G′) of 15 Pa, which can meet the need for efficient plugging. However, the nano-SiO_(2) enhanced HPAM/PEI polymer gel system showed weaker gel strength than that with nano-TiO_(2) at both 80 and 150 ℃ with G′ lower than 5 Pa. Microstructures showed that the nano-TiO_(2) enhanced HPAM/PEI gel had denser three-dimensional (3D) mesh structures, which makes the nano-TiO_(2) enhanced HPAM/PEI gel more firmly bound to water. The FT-IR results also confirmed that the chemical structure of the nano-TiO_(2) enhanced HPAM/PEI gel was more thermally stable than nano-SiO_(2) since there was a large amount of –OH groups on the structure surface. Therefore, nano-TiO_(2) was more suitable as the reinforcing material for HPAM/PEI gels for high-temperature petroleum reservoir conformance improvement.
基金Funded by National Natural Science Foundation of China(No.52278446)。
文摘In order to evaluate the feasibility of steel slag powder as filler,the coating properties of steel slag and limestone aggregate were compared by water boiling test,the micro morphology difierences between steel slag powder and mineral powder(limestone powder)were compared by scanning electron microscope(SEM),and the high-temperature rheological properties of asphalt mortar with difierent ratio of filler quality to asphalt quality(F/A)and difierent substitution rates of mineral powder(S/F)were studied by dynamic shear rheological test.The results show that the surface microstructure of steel slag powder is more abundant than that of mineral powder,and the adhesion of steel slag to asphalt is better than that of limestone.At the same temperature,the lower the ratio of S/F is,the greater the rutting factor and complex modulus will be.In addition,the complex modulus and rutting factor of the asphalt mortar increase with the increase of F/A,and the filler type and F/A have a negligible efiect on the phase angle.
基金financially supported by the Natural Science Foundation of Hunan Province(2020JJ5653)the National Natural Science Foundation of China(21875282,22102212)+1 种基金the National University of Defense Technology Scientific Research Project(ZK20-44)financial support from the Ministry of Science and Higher Education of the Russian Federation(075-15-2022-1150)。
文摘Embracing ultrahigh theoretical capacity of 3860 mA h g^(-1)and the lowest reduction potential of-3.04 V(versus standard hydrogen electrode),lithium(Li) is considered as the "holy grail" material for pursuing higher energy density,of which application has been challenged due to the unstable interface caused by the non-uniform electrodeposition as well as high chemical activity.Operating at higher temperature can be recommended to uniform electrodeposition of Li metal.Nevertheless,the intrinsic side-reaction between Li metal anode and electrolyte is inevitably aggravated and thus fosters the failure of Li metal anode rapidly with uneven electrodeposition.Here,a kind of temperature-tolerated ionic liquid(1-methyl-3-ethylimidazole bis(fluorosulfo nyl)imide/lithium bis(trifluoromethylsulfo nyl)imide,EF/LT)based electrolyte that matrixed with poly(vinylidene fluoride-hexafluoropropylene) was designed to maintain the interfacial stabilization of Li metal due to the weak interfacial reaction and uniform electrodeposition at high temperature of 80℃.It is the matter that the 660-h cycle with lower polarization is achieved with EF/LT-based electrolyte at temperature of 80 ℃ and the full cell embraces outstanding cyclic performance,without capacity fading within 100 cycles.Delighting,a door for practical application of Li metal anode for higher energy density as the carbon neutrality progresses in the blooming human society has been opened gradually.
基金supported by the National Natural Science Foundation of China(NSFC,Nos.52176199,and U20A20310)supported by the Program of Shanghai Academic/Technology Research Leader(22XD1423800)。
文摘Understanding the thermal safety evolution of lithium-ion batteries during high-temperature usage conditions bears significant implications for enhancing the safety management of aging batteries.This work investigates the thermal safety evolution mechanism of lithium-ion batteries during high-temperature aging.Similarities arise in the thermal safety evolution and degradation mechanisms for lithium-ion batteries undergoing cyclic aging and calendar aging.Employing multi-angle characterization analysis,the intricate mechanism governing the thermal safety evolution of lithium-ion batteries during high-temperature aging is clarified.Specifically,lithium plating serves as the pivotal factor contributing to the reduction in the self-heating initial temperature.Additionally,the crystal structure of the cathode induced by the dissolution of transition metals and the reductive gas generated during aging attacking the crystal structure of the cathode lead to a decrease in thermal runaway triggering temperature.Furthermore,the loss of active materials and active lithium during aging contributes to a decline in both the maximum temperature and the maximum temperature rise rate,ultimately indicating a decrease in the thermal hazards of aging batteries.
基金Funded by the Joint Fund of Ministry of Education for Equipment Pre-research(No.6141A02022250)the Fundamental Research Funds for the Central Universities,China(No.WUT:2021III003XZ)。
文摘The composites were prepared by modifying silicon carbide fiber with particles of zirconium carbide(ZrC)and boron carbide(B_(4)C)and incorporating them into a phenolic resin matrix.The influence of ZrC and B_(4)C on the mechanical performance of SiCf/phenolic composites after high-temperature pyrolysis was studied through flexural performance test.The results show that the composite material has good thermal stability and high-temperature mechanical properties.After static ablation at 1400℃ for 15 minutes,the flexural strength of the composite material reaches 286 MPa,which is still 7.3%higher than at room temperature,indicating that the composite material still has good mechanical properties even after heat treatment at 1400℃.
基金the National Key Research and Development Program of China(Grant No.2021YFB3601201)the National Natural Science Foundation of China(Grant No.62101057)the Fund of State Key Laboratory of Information Photonics and Optical Communications(Beijing University of Posts and Telecommunications)(Grant No.IPOC2021ZT07).
文摘Photonic crystal structures have excellent optical properties,so they are widely studied in conventional optical materials.Recent research shows that high-temperature superconducting periodic structures have natural photonic crystal features and they are favourable candidates for single-photon detection.Considering that superconductors have completely different properties from conventional optical materials,we study the energy level diagram and mid-infrared 3μm–5μm transmission spectrum of two-dimensional superconducting photonic crystals in both superconducting and quenched states with the finite element method.The energy level diagram of the circular crystal column superconducting structure shows that the structure has a large band gap width in both states.At the same fill factor,the circular crystal column superconducting structure has a larger band gap width than the others structures.For lattice structures,the zero transmission point of the square lattice structure is robust to the incident angle and environmental temperature.Our research has guiding significance for the design of new material photonic crystals,photon modulation and detection.
基金the Strategic Pilot Technology Chinese Academy of Sciences(No.XDA02010500).
文摘The high-temperature molten salt pump is the core equipment in a molten salt reactor that drives the flow of the molten salt coolant.Rotor stability is key to the continuous and reliable operation of the molten salt pump,and the liquid seal at the wear ring can affect the dynamic characteristics of the rotor system.When the molten salt pump is operated in the hightemperature molten salt medium,thermal deformation of the submerged parts inevitably occurs,changing clearance between the stator and rotor,affecting the leakage and dynamic characteristics of the seal.In this study,the seal leakage,seal dynamic characteristics,and rotor system dynamic characteristics are simulated and analyzed using finite element simulation software based on two cases of considering the effect of seal thermal deformation effect or not.The results show a significant difference in the leakage characteristics and dynamic characteristics of the seal obtained by considering the effect of seal thermal deformation and neglecting the effect of thermal deformation.The leakage flow rate decreases,and the first-order critical speed of the seal-bearing-rotor system decrease after considering the seal’s thermal deformation.
文摘Satellited CoNiCrAlY–Al_(2)O_(3)feedstocks with 2wt%, 4wt%, and 6wt% oxide nanoparticles and pure CoNiCrAlY powder were deposited by the high-velocity oxy fuel process on an Inconel738 superalloy substrate. The oxidation test was performed at 1050℃ for 5, 50, 100,150, 200, and 400 h. The microstructure and phase composition of powders and coatings were characterized by scanning electron microscopy and X-ray diffraction, respectively. The bonding strength of the coatings was also evaluated. The results proved that with the increase in the percentage of nanoparticles(from 2wt% to 6wt%), the amount of porosity(from 1vol% to 4.7vol%), unmelted particles, and roughness of the coatings(from 4.8 to 8.8 μm) increased, and the bonding strength decreased from 71 to 48 MPa. The thicknesses of the thermally grown oxide layer of pure and composite coatings(2wt%, 4wt%, and 6wt%) after 400 h oxidation were measured as 6.5, 5.5, 7.6, and 8.1 μm, respectively.The CoNiCrAlY–2wt% Al_(2)O_(3)coating showed the highest oxidation resistance due to the diffusion barrier effect of well-dispersed nanoparticles. The CoNiCrAlY–6wt% Al_(2)O_(3)coating had the lowest oxidation resistance due to its rough surface morphology and porous microstructure.
基金Supported by the National Natural Science Foundation of China(52288101).
文摘Three high-temperature resistant polymeric additives for water-based drilling fluids are designed and developed:weakly cross-linked zwitterionic polymer fluid loss reducer(WCZ),flexible polymer microsphere nano-plugging agent(FPM)and comb-structure polymeric lubricant(CSP).A high-temperature resistant and high-density polymeric saturated brine-based drilling fluid was developed for deep drilling.The WCZ has a good anti-polyelectrolyte effect and exhibits the API fluid loss less than 8 mL after aging in saturated salt environment at 200°C.The FPM can reduce the fluid loss by improving the quality of the mud cake and has a good plugging effect on nano-scale pores/fractures.The CSP,with a weight average molecular weight of 4804,has multiple polar adsorption sites and exhibits excellent lubricating performance under high temperature and high salt conditions.The developed drilling fluid system with a density of 2.0 g/cm^(3)has good rheological properties.It shows a fluid loss less than 15 mL at 200°C and high pressure,a sedimentation factor(SF)smaller than 0.52 after standing at high temperature for 5 d,and a rolling recovery of hydratable drill cuttings similar to oil-based drilling fluid.Besides,it has good plugging and lubricating performance.
基金financially supported by the UK Research Council EPSRC EP/009050/1。
文摘The doping of functionalized graphene oxide(GO)in the membranes becomes a promising method for improving the performance of high-temperature proton exchange membrane fuel cells(HT-PEMFC).Phosphonated graphene oxide(PGO)with a P/O ratio of 8.5%was quickly synthesised by one-step electrochemical exfoliation based on a three-dimensiaonal(3D)printed reactor and natural graphite flakes.Compared with the GO prepared by the two-step electrochemical exfoliation method,the PGO synthesized by the one-step electrochemical exfoliation can better improve the performance of the membrane-electrode-assembly(MEA)based on the polybenzimidazole(PBI)membrane in the HTPEMFC.The doping of 1.5 wt%GO synthesised by electrochemical exfoliation with the 2-step method or reactor method in PBI increased the peak power density by 17.4%or 35.4%compared to MEA based on pure PBI membrane at 150℃,respectively.In addition,the doping of PGO in PBI improves its durability under accelerated stress test(AST).
基金supported by Jiangsu Modern Agricultural Industrial Technology System(JATS[2022]489)Agricultural Science and Technology Independent Innovation Fund of Jiangsu Province(CX(22)3186)+1 种基金Policy Guidance Program of Jiangsu Province-Science and Technology Special Project of Northern Jiangsu Province(SZ-SQ2021041)the Qing Lan Project of Jiangsu Province and High-Level Talent Support Program of Yangzhou University.
文摘Tree peony(Paeonia suffruticosa Andr.)is a traditional Chinese flower,which prefers cool weather.However,high temperature in summer in the middle and lower reaches of the Yangtze River restricts its growth and development.In this study,osmotic regulation,antioxidant enzyme activities,and photosynthetic characteristics of tree peony in response to high-temperature stress were investigated.The results showed that high-temperature stress had destroyed the cell membrane,manifested as the increased relative electrical conductivity and malondialdehyde content.Moreover,high-temperature stress led to excessive accumulation of reactive oxygen species,thereby,activating antioxidant enzyme activities.Also,photosynthetic parameters and chlorophyll fluorescence parameters directly reflected the damage to the photosystem II reflection center under high-temperature stress.In addition,high-temperature stress led to stomatal closure and chloroplast damage.This study revealed the physiological responses of tree peony to high-temperature stress,laying a foundation for the promotion of tree peony in high-temperature areas and the improvement of high-temperature resistance.
基金the research grant of the National Natural Science Foundation of China(Grant No.52075125,No.52105331)The research was also partially supported by Shenzhen Science and Technology Innovation Committee(Grant No.JCYJ20210324124203009,No.JSGG20201102154600003,No.GXWD20220818163456002).
文摘The traditional nano-sintering or TLP techniques are generally expensive,time-consuming,and hence unsuitable for realizing practical mass production.Herein,we have developed an improved TLP process to rapidly produce IMC-skeleton structures across the bonding region by initiating a localized liquid-solid interaction among micron particles at traditional soldering temperatures.The developed IMC skeletons can reinforce solder alloys and provide remarkable mechanical stability and electrical capabilities at high temperatures.As a result,the IMC-skeleton strengthened interconnections exhibited higher thermal/electrical conductivity,lower hardness and almost doubled strength than traditional full-IMC joints,attaining 87.4 MPa and 30.2 MPa at room condition and 350℃.Meanwhile,the necessary heating time to form metallurgical bonds was shortened,one-fifth of nano-sintering and one-tenth of TLP bonding,and the material cost was significantly reduced.This proposed technique enabled the fast,low-cost manufacturing of electronics that can serve at temperatures as high as 200−350℃.Besides,the interfacial reactions among particles and the correlated phase evolution process were studied in this research.The formation mechanism of IMC skeletons was analyzed.The correlated influencing factors and their effect on the mechanical,thermal and electrical properties of joints were revealed,which may help the design and extensive uses of such techniques in various high-temperature/power applications.
基金supported by the Carbon Peak and Carbon Neutralization Science and Technology Innovation Special Fund of Jiangsu Province,China(No.BE2022859)Natural Science Foundation of Guangdong Province,China(No.2021A1515011763).
文摘Process heating constitutes a significant share of final energy consumption in the industrial sector around the world.In this paper,a high-temperature heat pump(HTHP)using flash tank vapor injection technology(FTVI)is proposed to develop low-temperature geothermal source for industrial process heating with temperature above 100°C.With heat sink output temperatures between 120°C and 150°C,the thermo-economic performance of the FTVI HTHP system using R1234ze(Z)as refrigerant is analyzed and also compared to the single-stage vapor compression(SSVC)system by employing the developed mathematical model.The coefficient of performance(COP),exergy efficiency(ηexe),net present value(NPV)and payback period(PBP)are used as performance indicators.The results show that under the typical working conditions,the COP andηexe of FTVI HTHP system are 3.00 and 59.66%,respectively,and the corresponding NPV and PBP reach 8.13×106 CNY and 4.13 years,respectively.Under the high-temperature heating conditions,the thermo-economic performance of the FTVI HTHP system is significantly better than that of the SSVC system,and the larger the temperature lift,the greater the thermo-economic advantage of the FTVI HTHP system.Additionally,the FTVI HTHP system is more capable than the SSVC system in absorbing the financial risks associated with changes of electricity price and natural gas price.
文摘After the first concrete was poured on December 9,2012 at the Shidao Bay site in Rongcheng,Shandong Province,China,the construction of the reactor building for the world’s first high-temperature gascooled reactor pebble-bed module(HTR-PM)demonstration power plant was completed in June,2015.Installation of the main equipment then began,and the power plant is currently progressing well toward connecting to the grid at the end of 2017.The thermal power of a single HTR-PM reactor module is 250 MWth,the helium temperatures at the reactor core inlet/outlet are 250/750℃,and a steam of 13.25 MPa/567℃ is produced at the steam generator outlet.Two HTR-PM reactor modules are connected to a steam turbine to form a 210 MWe nuclear power plant.Due to China’s industrial capability,we were able to overcome great difficulties,manufacture first-of-a-kind equipment,and realize series major technological innovations.We have achieved successful results in many aspects,including planning and implementing R&D,establishing an industrial partnership,manufacturing equipment,fuel production,licensing,site preparation,and balancing safety and economics;these obtained experiences may also be referenced by the global nuclear community.
文摘To solve the problem of the severe mismatch between the product and roll materials in the preliminary rolling line,a new graphitic steel material was designed,its microstructure and high-temperature friction and wear properties were investigated.Moreover,the feasibility of replacing semi-steel with this new material in the V1 stand roll was studied herein.The results show that the graphitic steel matrix is strengthened by silicon and nickel elements.The presence of spherical graphite also provides self-lubrication and heat conduction and prevents the propagation of cracks.Carbides in the appropriate amount and size strengthen the matrix,reduce the cracking effect of the matrix,and are not easily broken,thereby reducing high-temperature abrasive wear.Under the same hightemperature friction and wear conditions,compared with semi-steel,the wear-scar surface of graphitic steel exhibits less wear-scar depth and wear volume,a smaller friction coefficient,reduced oxide layer thickness,and fewer instances of peeling and microcracks.Therefore,the newly designed graphitic steel has higher wear resistance and hot-crack resistance than semi-steel,which makes it feasible for use in replacing semi-steel as a new V1 frame roll material in the blooming mill.
