The present work discusses the experimental study on wire-cut electric discharge machining of hot-pressed boron carbide.The effects of machining parameters,such as pulse on time(TON),peak current(IP),flushing pressure...The present work discusses the experimental study on wire-cut electric discharge machining of hot-pressed boron carbide.The effects of machining parameters,such as pulse on time(TON),peak current(IP),flushing pressure(FP) and spark voltage on material removal rate(MRR)and surface roughness(R_a) of the material,have been evaluated.These parameters are found to have an effect on the surface integrity of boron carbide machined samples.Wear rate of brass wire increases with rise in input energy in machining of hot-pressed boron carbide.The surfaces of machined samples were examined using scanning electron microscopy(SEM).The influence of machining parameters on mechanism of MRR and R_a was described.It was demonstrated that higher TON and peak current deteriorate the surface finish of boron carbide samples and result in the formation of large craters,debris and micro cracks.The generation of spherical particles was noticed and it was attributed to surface tension of molten material.Macro-ridges were also observed on the surface due to protrusion of molten material at higher discharge energy levels.展开更多
Boron carbide has unique properties for wide application possibilities;however,poor sinterability limits its applications.One approach to overcome this limitation is the addition of secondary phases into boron carbide...Boron carbide has unique properties for wide application possibilities;however,poor sinterability limits its applications.One approach to overcome this limitation is the addition of secondary phases into boron carbide.Boron carbide based composite ceramics are produced by the direct addition of secondary phases into the structure or via reactive sintering using a sintering additive.The present study investigated the effect of Ti_(3)SiC_(2) addition to boron carbide by reactive spark plasma sintering in the range of 1700-1900℃.Ti_(3)SiC_(2) phase decomposed at high temperatures and reacted with B4C to form secondary phases of TiB2 and SiC.The results demonstrated that the increase of Ti_(3)SiC_(2) addition(up to 15 vol%)effectively promoted the densification of B4C and yielded higher hardness.However,as the amount of Ti_(3)SiC_(2) increased further,the formation of microstructural inhomogeneity and agglomeration of secondary phases caused a decrease in hardness.展开更多
Grain boundaries(GBs)play a significant role in the deformation behaviors of nanocrystalline ceramics.Here,we investigate the compression behaviors of nanocrystalline boron carbide(nB_(4)C)with varying grain sizes usi...Grain boundaries(GBs)play a significant role in the deformation behaviors of nanocrystalline ceramics.Here,we investigate the compression behaviors of nanocrystalline boron carbide(nB_(4)C)with varying grain sizes using molecular dynamics simulations with a machine-learning force field.The results reveal quasi-plastic deformation mechanisms in nB_(4)C:GB sliding,intergranular amorphization and intragranular amorphization.GB sliding arises from the presence of soft GBs,leading to intergranular amorphization.Intragranular amorphization arises from the interaction between grains with unfavorable orientations and the softened amorphous GBs,and finally causes structural failure.Furthermore,nB_(4)C models with varying grain sizes from 4.07 nm to 10.86 nm display an inverse Hall-Petch relationship due to the GB sliding mechanism.A higher strain rate in nB_(4)C often leads to a higher yield strength,following a 2/3 power relationship.These deformation mechanisms are critical for the design of ceramics with superior mechanical properties.展开更多
The oxidation behavior at 973 1 273 K and the effect of oxidation on the room temperature tribological properties of hot pressed boron carbide ceramic were investigated. Oxidized samples were studied by X ray diffract...The oxidation behavior at 973 1 273 K and the effect of oxidation on the room temperature tribological properties of hot pressed boron carbide ceramic were investigated. Oxidized samples were studied by X ray diffractometer and scanning electron microscopy. It is demonstrated that the oxidation results in the formation of a thin transparent B 2O 3 film, and the oxide film is severely cracked during cooling due to the thermal expansion mismatch between the oxide film and B 4C substrate. B 2O 3 reacts with moisture in air to form boric acid, which is a kind of solid lubricant. The sliding friction factors of oxidized B 4C pair are about 0.05 0.08, compared to 0.25 0.35 of the as received B 4C pair. When the oxidation temperature is up to 1 273 K, severe unstability and increase of friction factor are observed. Visual inspection of the wear track reveals that the lubricant film is broken and some debris particles occur on and around the rubbing surfaces, because the friction interface is rough by the severe etching of grain boundaries.展开更多
Carbide ceramic fibers are of significant importance for application in the high-tech areas of advanced aircraft engines,aerospace vehicles,and the nuclear industry due to their excellent properties,such as high tensi...Carbide ceramic fibers are of significant importance for application in the high-tech areas of advanced aircraft engines,aerospace vehicles,and the nuclear industry due to their excellent properties,such as high tensile strength and elastic modulus,excellent high-temperature resistance,and oxidation resistance.This paper reviews the preparation and application of different carbide ceramic fibers,including SiC fibers and transition metal carbide(e.g.,ZrC,HfC,and TaC)ceramic fibers.The preparation methods of carbide ceramic fibers are discussed in terms of different fiber diameters,represented by SiC fibers with variable weaving properties and functions due to their differences in diameter.Subsequently,the application of carbide ceramic fibers as high-temperature-resistant structural materials,catalyst carriers,sensors,and supercapacitors are summarized,and strategies for the future development of carbide ceramic fibers are proposed.This review aims to help researchers enhance their understanding of the preparation and utilization of carbide ceramic micro/nanofibers,advancing the development of high-performance carbide ceramic fibers.展开更多
Boron carbide(B_(4)C)has excellent high-temperature oxidation resistance,high hardness,low relative density,high melting point and excellent abrasive resistance,which is widely used in fields such as refractories,wear...Boron carbide(B_(4)C)has excellent high-temperature oxidation resistance,high hardness,low relative density,high melting point and excellent abrasive resistance,which is widely used in fields such as refractories,wear-resistant materials and lightweight protective materials.The research progress and application of B_(4)C materials in China and overseas in recent years were summarized.The influences of sintering processes(pressureless sintering,hot-pressing sintering,hot isostatic pressing sintering,spark plasma sintering and microwave sintering)and sintering additives(simple substances,oxides and carbides)on the B_(4)C densification were analyzed.The development of B_(4)C materials was prospected.展开更多
The unique structural and physical properties of boron carbide, which make it suitable for a wide range of applications,demands the development of low-cost and green synthesis method. In the present work, the commonly...The unique structural and physical properties of boron carbide, which make it suitable for a wide range of applications,demands the development of low-cost and green synthesis method. In the present work, the commonly available leaves of aloe vera are hydrothermally treated to form the carbon precursor for the synthesis of boron carbide. The morphological characterization reveals the porous nature of the precursor turning into a tubular structure upon boron carbide formation.The structural characterization by x-ray diffraction and other spectroscopic techniques such as Fourier transform infrared,Raman, photoluminescence and uv-visible near-infrared spectroscopy confirm the formation of boron carbide. The thermogravimetric analysis of the sample is found to exhibit good thermal stability above 500 °C. When the sample is annealed to 600 °C, boron carbide with phase purity is obtained, which is confirmed through XRD and FTIR analyses. The optical emission properties of the sample are studied through CIE plot and power spectrum. Compared with other natural precursors for boron carbide, the aloe vera is found to give a good yield above 50%.展开更多
In this experimental study,magnesium(AZ91D)based boron carbide(B4C)and graphite(Gr)particle reinforced hybrid composite materials were manufactured by stir casting.The tribological and mechanical properties of these c...In this experimental study,magnesium(AZ91D)based boron carbide(B4C)and graphite(Gr)particle reinforced hybrid composite materials were manufactured by stir casting.The tribological and mechanical properties of these composite materials were investigated.The results of the tests revealed that the graphite reinforced hybrid composites exhibited a lower wear loss compared to the unreinforced AZ91D alloy and AZ91D–B4C composites.It was found that with an increase in the B4C content,the wear resistance increased monotonically with hardness and ultimate tensile strength decreased.This study revealed that the addition of both a hard reinforcement(e.g.,B4C)and soft reinforcement(e.g.,graphite)significantly improves the wear resistance of magnesium composites.These entire results designate that the hybrid magnesium composites can be considered as an excellent material where high strength,ultimate tensile strength and wear-resistant components are of major importance,primarily in the aerospace and automotive engineering sectors.展开更多
Boron-doped diamond(BDD)films were deposited on the tungsten carbide substrates at different substrate temperatures ranging from 450 to 850°C by hot filament chemical vapor deposition(HFCVD)method.The effect of d...Boron-doped diamond(BDD)films were deposited on the tungsten carbide substrates at different substrate temperatures ranging from 450 to 850°C by hot filament chemical vapor deposition(HFCVD)method.The effect of deposition temperature on the properties of the boron-doped diamond films on tungsten carbide substrate was investigated.It is found that boron doping obviously enhances the growth rate of diamond films.A relatively high growth rate of 544 nm/h was obtained for the BDD film deposited on the tungsten carbide at 650°C.The added boron-containing precursor gas apparently reduced activation energy of film growth to be 53.1 kJ/mol,thus accelerated the rate of deposition chemical reaction.Moreover,Raman and XRD analysis showed that heavy boron doping(750 and 850°C)deteriorated the diamond crystallinity and produced a high defect density in the BDD films.Overall,600-700°C is found to be an optimum substrate temperature range for depositing BDD films on tungsten carbide substrate.展开更多
The sluggish kinetics of Fe(Ⅱ)recovery in Fenton/Fenton-like reactions significantly limits the oxidation efficiency.In this study,we for the first time use boron carbide(BC)as a green and stable promotor to enhance ...The sluggish kinetics of Fe(Ⅱ)recovery in Fenton/Fenton-like reactions significantly limits the oxidation efficiency.In this study,we for the first time use boron carbide(BC)as a green and stable promotor to enhance the reaction of Fe(Ⅲ)/H_(2)O_(2) for degradation of diverse organic pollutants.Electron paramagnetic resonance analysis and chemical quenching/capturing experiments demonstrate that hydroxyl radicals(·OH)are the primary reactive species in the BC/Fe(Ⅲ)/H_(2)O_(2) system.In situ electrochemical analysis indicates that BC remarkably boosts the Fe(Ⅲ)/Fe(Ⅱ)redox cycles,where the adsorbed Fe(Ⅲ)cations were transformed to more active Fe(Ⅲ)species with a higher oxidative potential to react with H_(2)O_(2) to produce Fe(Ⅱ).Thus,the recovery of Fe(Ⅱ)from Fe(Ⅲ)is facilitated over BC surface,which enhancesOH generation via Fenton reactions.Moreover,BC exhibits outstanding reusability and stability in successive cycles and avoids the secondary pollution caused by conventional organic and metalliferous promotors.Therefore,metal-free BC boosting Fe(Ⅲ)/H_(2)O_(2) oxidation of organics provides a green and advanced strategy for water decontamination.展开更多
The present research work reports the fabrication and evaluation of the mechanical properties of hybrid aluminium matrix composites(HAMC). Aluminium 7075(Al7075) alloy was reinforced with particles of boron carbide(B_...The present research work reports the fabrication and evaluation of the mechanical properties of hybrid aluminium matrix composites(HAMC). Aluminium 7075(Al7075) alloy was reinforced with particles of boron carbide(B_4 C) and coconut shell fly ash(CSFA). Al7075 matrix composites were fabricated by stir casting method. The samples of Al7075 HAMC were fabricated with different weight percentages of(0, 3, 6, 9 and 12 wt.%) B_4 C and 3 wt.% of CSFA. The mechanical properties discussed in this work are hardness, tensile strength, and impact strength. Hardness of the composites increased 33% by reinforcements of 12 wt.% B_4 C and 3 wt.% CSFA in aluminium 7075 alloy. The tensile strength of the composites increased 66% by the addition of 9 wt.% B_4 C and 3 wt.% CSFA in aluminium 7075 alloy. Further addition of reinforcements decreased the tensile strength of the composites. Elongation of the composites decreased while increasing B_4 C and CSFA reinforcements in the matrix. The impact energy of the composites increased up to 2.3 J with 9 wt.% B_4 C and 3 wt.% CSFA addition in aluminium alloy. Further addition of reinforcement decreased the impact strength of the composites. The optical micrographs disclosed the homogeneous distribution of reinforcement particles(B_4 C and CSFA) in Al7075 matrix. The homogeneously distributed B_4 C and CSFA particles added as reinforcement in the Al7075 alloy contributed to the improvement of hardness, tensile strength, and impact strength of the composites.展开更多
The properties of boron carbide-lanthanum boride composite material prepared by hot pressed sintering method was tested, and lanthanum boride as a sintering aid for boron carbide was investigated. The result shows tha...The properties of boron carbide-lanthanum boride composite material prepared by hot pressed sintering method was tested, and lanthanum boride as a sintering aid for boron carbide was investigated. The result shows that the hardness of boron carbide-lanthanum boride increases with the increasing content of lanthanum boride. When the content of the lanthanum boride is 6%, the hardness reaches its supreme value of 31.83 GPa, and its hardness is improved nearly 20.52% compared to monolithic boron carbide. The content of the lanthanum boride does not greatly affect flexibility strength, however, it gives much effect on fracture toughness. The curve of fracture toughness likes the form of saw-toothed wave as the content of lanthanum boride increases in the test. When the content of the lanthanum boride is 6%, the fracture toughness reaches its supreme value of 5.14 MPa·m 1/2, which is improved nearly 39.67% compared with monolithic boron carbide materials. The fracture scanning electric microscope analysis of boron carbide-lanthanum boride composite material shows that, with the increase of the content of lanthanum boride, the interior station of monolithic boron carbide is changed. The crystallite arrangement is so compact that pores disappear gradually. The main fracture way of boron carbide-lanthanum boride composite material is intercrystalline rupture, while the transcrystalline rupture is minor, which is in accordance with fracture mechanism of ceramic material. It indicates that this change of fracture mode by the addition of lanthanum boride gives rise to the improvement of the fracture toughness.展开更多
Structural characteristics, chemical bonds and thermoelectric properties of Al-doped boron carbides are studied through calculations of various structural unit models by using a self-consistent-field discrete variatio...Structural characteristics, chemical bonds and thermoelectric properties of Al-doped boron carbides are studied through calculations of various structural unit models by using a self-consistent-field discrete variation X. method. The calculations show that Al atom doped in boron carbide is in preference to substituting B or C atoms on the end of boron carbide chain, and then may occupy interstitial sites, but it is difficult for Al to substitute B or C atom in the centers of the chain or in the icosahedra. A representative structural unit containing an Al atom is [C - B -Al]-[B11C]-,while the structural unit without Al is [C-B-B(C)]- - [B11C]C+, and the coexistence of these two different structural units makes the electrical conductivity increased. As the covalent bond of Al-B or Al-C is weaker than that of B-B or B-C, the thermal conductivity decreases when Al is added into boron carbides. With the electrical conductivity increasing and the thermal conductivity decreases, Al doping has significant effect on thermoelectric properties of baron carbides.展开更多
High velocity ballistic impact deformation behaviour of Titanium/GFRP Fiber Metal Laminates(FML)has been explored.Both single and multiple projectiles impact conditions were considered.Ti/GFRP FML targets were fabrica...High velocity ballistic impact deformation behaviour of Titanium/GFRP Fiber Metal Laminates(FML)has been explored.Both single and multiple projectiles impact conditions were considered.Ti/GFRP FML targets were fabricated with addition of 5%and 10%weight percentage of boron carbide(B_(4)C)particles.Mechanical properties of Ti/GFRP FML targets were determined as per ASTM standards.High velocity ballistic experiments were conducted using Armour Piercing Projectile(APP)of diameter 7.62 mm and velocity ranging between 350 and 450 m/s.Depth of penetration of the projectile into the target was measured.The deformation behaviour of Ti/GFRP targets with and without the presence of ceramic powder(B_(4)C)was investigated.“Ductile hole growth”failure mode was observed for pure GFRP target when subjected to single projectile impact whereas“plugging”failure mode was noted for Ti/GFRP targets.The presence of B_(4)C(5%by weight)particles has significantly improved the ballistic resistance of the Ti/GFRP FML target by offering frictional resistance to the projectile penetration.Further addition(10%by weight)of B_(4)C has reduced the ballistic performance due to agglomeration.None of the targets showed‘brittle cracking’or‘fragmentation’failures.When compared to the published results of Aluminium(Al 1100/GFRP and Al 6061/GFRP)FMLs,Ti/GFRP FML showed lesser DoP which increases its potential application to aerospace industry.展开更多
Different pre-heating of boron carbide particles for reinforcement and different processing conditions were studied in this work. Being one of the most cost-effective industrial methods, conventional melt stir-casting...Different pre-heating of boron carbide particles for reinforcement and different processing conditions were studied in this work. Being one of the most cost-effective industrial methods, conventional melt stir-casting route was utilized.Result showed that the boron carbide particles distributed well for a suitable pre-heating temperature and processed in air.No reaction product was found at the A1-B4C interfaces at the resolution limit of SEM used in that way.展开更多
High strength-to-weight ratio of non-ferrous alloys, such as aluminium, magnesium and titanium alloys, are considered to be possible replacement of widely accepted steels in transportation and automobile sectors. Amon...High strength-to-weight ratio of non-ferrous alloys, such as aluminium, magnesium and titanium alloys, are considered to be possible replacement of widely accepted steels in transportation and automobile sectors. Among these alloys, magnesium is self explosive and titanium is costlier, and aluminium is most likely to replace steels. Application of aluminium or its alloys is also thought of as an appropriate replacement in defence field, especially to enhance the easiness in mobility of combat vehicles while maintaining the same standard as that of conventional armour grade steels. Hence most of the investigations have been confined to aluminium or its alloys as base material and open an era of developing the newer composite materials to address the major limitation, i.e. tribological properties. The surface composites can be fabricated by incorporating the ceramic carbides like silicon carbide, carbides of transition metals and oxides of aluminium using surface modification techniques, such as high energy laser melt treatment, high energy electron beam irradiation and thermal spray process which are based on fusion route. These techniques yield the fusion related problems, such as interfacial reaction, pin holes, shrinkage cavities or voids and other casting related defects, and pave the way to need of an efficient technique which must be based on solid state. Recently developed friction stir processing technique was used in the present investigation for surface modification of AA7075 aluminum alloy, which is an alternative to steels. In the present investigation, 160 μm sized boron carbide powder was procured and was reduced to 60 μm and 30 μm using high energy ball mill. Subsequently these powders were used to fabricate the surface composites using friction stir processing.Ballistic performance testing as per the military standard(JIS.0108.01) was carried out. In the present work, an analytical method of predicting the ballistic behavior of surface composites was developed. This method was based on energy balance, i.e., the initial energy of impact is same as that of energy absorbed by multi layers. An attempt also has been made to validate the analytical results with the experimental findings. Variation between the analytical and experimental results may be accounted due to the assumptions considering such as isotropic behavior of target and shearing area of contact as cylindrical instead of conical interface As the analytical model yields the ballistic performance in the closer proximity of experimentally obtained, it can be considered to be an approximation to evaluate the ballistic performance of targets.展开更多
Reduced graphene oxide(rGO)enhanced B_(4)C ceramics was prepared by SPS sintering,the enhancement effect of rGO on the microstructure and mechanical properties of composites was studied through experiments and numeric...Reduced graphene oxide(rGO)enhanced B_(4)C ceramics was prepared by SPS sintering,the enhancement effect of rGO on the microstructure and mechanical properties of composites was studied through experiments and numerical simulation.The results show that the composite with 2wt%rGO has the best comprehensive mechanical properties.Compared with pure boron carbide,vickers hardness and bending strength are increased by 4.8%and 21.96%,respectively.The fracture toughness is improved by 25.71%.The microstructure observation shows that the improvement of mechanical properties is mainly attributed to the pullout and bridge mechanism of rGO and the crack deflection.Based on the cohesive force finite element method,the dynamic crack growth process of composites was simulated.The energy dissipation of B_(4)C/rGO multiphase ceramics during crack propagation was calculated and compared with that of pure boron carbide ceramics.The results show that the fracture energy dissipation can be effectively increased by adding graphene.展开更多
Microstructure of plasma spray boron carbide coating was studied by SEM and TEM. Its physical, mechanical and electrical properties were measured. The results showed that high microhardness, modulus and low porosity o...Microstructure of plasma spray boron carbide coating was studied by SEM and TEM. Its physical, mechanical and electrical properties were measured. The results showed that high microhardness, modulus and low porosity of B4C coating were manufactured by plasma spray. It was lamellar packing and dense. The B4C coating examined here contained two principal structures and two impurity phase besides major phase. The relatively small value of Young's modulus, comparing with that of the bulk materials, is explained by porosity . The Fe impurity phase could account for the relatively high electrical conductivity of boron carbide coating by comparing with the general boron carbide materials.展开更多
This paper reports that the large-scale single crystalline boron carbide nanobelts have been fabricated through a simple carbothermal reduction method with B/B2O3/C/Fe powder as precursors at 1100℃. Transmission elec...This paper reports that the large-scale single crystalline boron carbide nanobelts have been fabricated through a simple carbothermal reduction method with B/B2O3/C/Fe powder as precursors at 1100℃. Transmission electron microscopy and selected area electron diffraction characterizations show that the boron carbide nanobelt has a B4C rhomb-centred hexagonal structure with good crystallization. Electron energy loss spectroscopy analysis indicates that the nanobelt contains only B and C, and the atomic ratio of B to C is close to 4：1. High resolution transmission electron microscopy results show that the preferential growth direction of the nanobelt is [101]. A possible growth mechanism is also discussed.展开更多
We researched the electric heating property from butyl rubber-loaded boron carbide composite. The effects of boron carbide content on bulk resistivity, voltage-current characteristic, thermal conductivity and thermal ...We researched the electric heating property from butyl rubber-loaded boron carbide composite. The effects of boron carbide content on bulk resistivity, voltage-current characteristic, thermal conductivity and thermal stability of boron carbide / butyl rubber （IIR） polymer composite were introduced. The analysis results indicated that the bulk resistivity decreased greatly with increasing boron carbide content, and when boron carbide content reached to 60%, the bulk resistivity achieved the minimum. Accordingly, electric heating behavior of the composite is strongly dependent on boron carbide content as well as applied voltage. The content of boron carbide was found to be effective in achieving high thermal conductivity in composite systems. The thermal conductivity of the composite material with added boron carbide was improved nearly 20 times than that of the pure IIR. The thermal stability test showed that, compared with pure IIR, the thermal stable time of composites was markedly extended, which indicated that the boron carbide can significantly improve the thermal stability of boron carbide / IIR composite.展开更多
文摘The present work discusses the experimental study on wire-cut electric discharge machining of hot-pressed boron carbide.The effects of machining parameters,such as pulse on time(TON),peak current(IP),flushing pressure(FP) and spark voltage on material removal rate(MRR)and surface roughness(R_a) of the material,have been evaluated.These parameters are found to have an effect on the surface integrity of boron carbide machined samples.Wear rate of brass wire increases with rise in input energy in machining of hot-pressed boron carbide.The surfaces of machined samples were examined using scanning electron microscopy(SEM).The influence of machining parameters on mechanism of MRR and R_a was described.It was demonstrated that higher TON and peak current deteriorate the surface finish of boron carbide samples and result in the formation of large craters,debris and micro cracks.The generation of spherical particles was noticed and it was attributed to surface tension of molten material.Macro-ridges were also observed on the surface due to protrusion of molten material at higher discharge energy levels.
基金YOK(MEVLANA 2018-9999-Proj-ect-Based International Exchange Programme)for financial support in inter-national collaboration.
文摘Boron carbide has unique properties for wide application possibilities;however,poor sinterability limits its applications.One approach to overcome this limitation is the addition of secondary phases into boron carbide.Boron carbide based composite ceramics are produced by the direct addition of secondary phases into the structure or via reactive sintering using a sintering additive.The present study investigated the effect of Ti_(3)SiC_(2) addition to boron carbide by reactive spark plasma sintering in the range of 1700-1900℃.Ti_(3)SiC_(2) phase decomposed at high temperatures and reacted with B4C to form secondary phases of TiB2 and SiC.The results demonstrated that the increase of Ti_(3)SiC_(2) addition(up to 15 vol%)effectively promoted the densification of B4C and yielded higher hardness.However,as the amount of Ti_(3)SiC_(2) increased further,the formation of microstructural inhomogeneity and agglomeration of secondary phases caused a decrease in hardness.
基金the support from the National Natural Science Foundation of China (Grant No.11972267)。
文摘Grain boundaries(GBs)play a significant role in the deformation behaviors of nanocrystalline ceramics.Here,we investigate the compression behaviors of nanocrystalline boron carbide(nB_(4)C)with varying grain sizes using molecular dynamics simulations with a machine-learning force field.The results reveal quasi-plastic deformation mechanisms in nB_(4)C:GB sliding,intergranular amorphization and intragranular amorphization.GB sliding arises from the presence of soft GBs,leading to intergranular amorphization.Intragranular amorphization arises from the interaction between grains with unfavorable orientations and the softened amorphous GBs,and finally causes structural failure.Furthermore,nB_(4)C models with varying grain sizes from 4.07 nm to 10.86 nm display an inverse Hall-Petch relationship due to the GB sliding mechanism.A higher strain rate in nB_(4)C often leads to a higher yield strength,following a 2/3 power relationship.These deformation mechanisms are critical for the design of ceramics with superior mechanical properties.
文摘The oxidation behavior at 973 1 273 K and the effect of oxidation on the room temperature tribological properties of hot pressed boron carbide ceramic were investigated. Oxidized samples were studied by X ray diffractometer and scanning electron microscopy. It is demonstrated that the oxidation results in the formation of a thin transparent B 2O 3 film, and the oxide film is severely cracked during cooling due to the thermal expansion mismatch between the oxide film and B 4C substrate. B 2O 3 reacts with moisture in air to form boric acid, which is a kind of solid lubricant. The sliding friction factors of oxidized B 4C pair are about 0.05 0.08, compared to 0.25 0.35 of the as received B 4C pair. When the oxidation temperature is up to 1 273 K, severe unstability and increase of friction factor are observed. Visual inspection of the wear track reveals that the lubricant film is broken and some debris particles occur on and around the rubbing surfaces, because the friction interface is rough by the severe etching of grain boundaries.
基金support from the National Natural Science Foundation of China(No.52272100)the Natural Science Foundation of Hunan Province(No.2022JJ30662)the Science and Technology on Advanced Ceramic Fibers and Composites Laboratory(No.WDZC20215250507).
文摘Carbide ceramic fibers are of significant importance for application in the high-tech areas of advanced aircraft engines,aerospace vehicles,and the nuclear industry due to their excellent properties,such as high tensile strength and elastic modulus,excellent high-temperature resistance,and oxidation resistance.This paper reviews the preparation and application of different carbide ceramic fibers,including SiC fibers and transition metal carbide(e.g.,ZrC,HfC,and TaC)ceramic fibers.The preparation methods of carbide ceramic fibers are discussed in terms of different fiber diameters,represented by SiC fibers with variable weaving properties and functions due to their differences in diameter.Subsequently,the application of carbide ceramic fibers as high-temperature-resistant structural materials,catalyst carriers,sensors,and supercapacitors are summarized,and strategies for the future development of carbide ceramic fibers are proposed.This review aims to help researchers enhance their understanding of the preparation and utilization of carbide ceramic micro/nanofibers,advancing the development of high-performance carbide ceramic fibers.
文摘Boron carbide(B_(4)C)has excellent high-temperature oxidation resistance,high hardness,low relative density,high melting point and excellent abrasive resistance,which is widely used in fields such as refractories,wear-resistant materials and lightweight protective materials.The research progress and application of B_(4)C materials in China and overseas in recent years were summarized.The influences of sintering processes(pressureless sintering,hot-pressing sintering,hot isostatic pressing sintering,spark plasma sintering and microwave sintering)and sintering additives(simple substances,oxides and carbides)on the B_(4)C densification were analyzed.The development of B_(4)C materials was prospected.
基金support from UGC-SAP (DRS, Phase Ⅲ) with Sanction order No. F.510/3/DRS-Ⅲ/2015(SAPI)UGC-MRP with F. No. 43-539/2014 (SR)FD Diary No.3668
文摘The unique structural and physical properties of boron carbide, which make it suitable for a wide range of applications,demands the development of low-cost and green synthesis method. In the present work, the commonly available leaves of aloe vera are hydrothermally treated to form the carbon precursor for the synthesis of boron carbide. The morphological characterization reveals the porous nature of the precursor turning into a tubular structure upon boron carbide formation.The structural characterization by x-ray diffraction and other spectroscopic techniques such as Fourier transform infrared,Raman, photoluminescence and uv-visible near-infrared spectroscopy confirm the formation of boron carbide. The thermogravimetric analysis of the sample is found to exhibit good thermal stability above 500 °C. When the sample is annealed to 600 °C, boron carbide with phase purity is obtained, which is confirmed through XRD and FTIR analyses. The optical emission properties of the sample are studied through CIE plot and power spectrum. Compared with other natural precursors for boron carbide, the aloe vera is found to give a good yield above 50%.
文摘In this experimental study,magnesium(AZ91D)based boron carbide(B4C)and graphite(Gr)particle reinforced hybrid composite materials were manufactured by stir casting.The tribological and mechanical properties of these composite materials were investigated.The results of the tests revealed that the graphite reinforced hybrid composites exhibited a lower wear loss compared to the unreinforced AZ91D alloy and AZ91D–B4C composites.It was found that with an increase in the B4C content,the wear resistance increased monotonically with hardness and ultimate tensile strength decreased.This study revealed that the addition of both a hard reinforcement(e.g.,B4C)and soft reinforcement(e.g.,graphite)significantly improves the wear resistance of magnesium composites.These entire results designate that the hybrid magnesium composites can be considered as an excellent material where high strength,ultimate tensile strength and wear-resistant components are of major importance,primarily in the aerospace and automotive engineering sectors.
基金Project(51375011)supported by the National Natural Science Foundation of ChinaProject(15cxy49)supported by the Shanghai Municipal Education Commission,ChinaProject(16PJ025)supported by the Shanghai Pujiang Program,China
文摘Boron-doped diamond(BDD)films were deposited on the tungsten carbide substrates at different substrate temperatures ranging from 450 to 850°C by hot filament chemical vapor deposition(HFCVD)method.The effect of deposition temperature on the properties of the boron-doped diamond films on tungsten carbide substrate was investigated.It is found that boron doping obviously enhances the growth rate of diamond films.A relatively high growth rate of 544 nm/h was obtained for the BDD film deposited on the tungsten carbide at 650°C.The added boron-containing precursor gas apparently reduced activation energy of film growth to be 53.1 kJ/mol,thus accelerated the rate of deposition chemical reaction.Moreover,Raman and XRD analysis showed that heavy boron doping(750 and 850°C)deteriorated the diamond crystallinity and produced a high defect density in the BDD films.Overall,600-700°C is found to be an optimum substrate temperature range for depositing BDD films on tungsten carbide substrate.
基金support to visit The University of Adelaide from the China Scholarship Council(No.201906240037).
文摘The sluggish kinetics of Fe(Ⅱ)recovery in Fenton/Fenton-like reactions significantly limits the oxidation efficiency.In this study,we for the first time use boron carbide(BC)as a green and stable promotor to enhance the reaction of Fe(Ⅲ)/H_(2)O_(2) for degradation of diverse organic pollutants.Electron paramagnetic resonance analysis and chemical quenching/capturing experiments demonstrate that hydroxyl radicals(·OH)are the primary reactive species in the BC/Fe(Ⅲ)/H_(2)O_(2) system.In situ electrochemical analysis indicates that BC remarkably boosts the Fe(Ⅲ)/Fe(Ⅱ)redox cycles,where the adsorbed Fe(Ⅲ)cations were transformed to more active Fe(Ⅲ)species with a higher oxidative potential to react with H_(2)O_(2) to produce Fe(Ⅱ).Thus,the recovery of Fe(Ⅱ)from Fe(Ⅲ)is facilitated over BC surface,which enhancesOH generation via Fenton reactions.Moreover,BC exhibits outstanding reusability and stability in successive cycles and avoids the secondary pollution caused by conventional organic and metalliferous promotors.Therefore,metal-free BC boosting Fe(Ⅲ)/H_(2)O_(2) oxidation of organics provides a green and advanced strategy for water decontamination.
文摘The present research work reports the fabrication and evaluation of the mechanical properties of hybrid aluminium matrix composites(HAMC). Aluminium 7075(Al7075) alloy was reinforced with particles of boron carbide(B_4 C) and coconut shell fly ash(CSFA). Al7075 matrix composites were fabricated by stir casting method. The samples of Al7075 HAMC were fabricated with different weight percentages of(0, 3, 6, 9 and 12 wt.%) B_4 C and 3 wt.% of CSFA. The mechanical properties discussed in this work are hardness, tensile strength, and impact strength. Hardness of the composites increased 33% by reinforcements of 12 wt.% B_4 C and 3 wt.% CSFA in aluminium 7075 alloy. The tensile strength of the composites increased 66% by the addition of 9 wt.% B_4 C and 3 wt.% CSFA in aluminium 7075 alloy. Further addition of reinforcements decreased the tensile strength of the composites. Elongation of the composites decreased while increasing B_4 C and CSFA reinforcements in the matrix. The impact energy of the composites increased up to 2.3 J with 9 wt.% B_4 C and 3 wt.% CSFA addition in aluminium alloy. Further addition of reinforcement decreased the impact strength of the composites. The optical micrographs disclosed the homogeneous distribution of reinforcement particles(B_4 C and CSFA) in Al7075 matrix. The homogeneously distributed B_4 C and CSFA particles added as reinforcement in the Al7075 alloy contributed to the improvement of hardness, tensile strength, and impact strength of the composites.
文摘The properties of boron carbide-lanthanum boride composite material prepared by hot pressed sintering method was tested, and lanthanum boride as a sintering aid for boron carbide was investigated. The result shows that the hardness of boron carbide-lanthanum boride increases with the increasing content of lanthanum boride. When the content of the lanthanum boride is 6%, the hardness reaches its supreme value of 31.83 GPa, and its hardness is improved nearly 20.52% compared to monolithic boron carbide. The content of the lanthanum boride does not greatly affect flexibility strength, however, it gives much effect on fracture toughness. The curve of fracture toughness likes the form of saw-toothed wave as the content of lanthanum boride increases in the test. When the content of the lanthanum boride is 6%, the fracture toughness reaches its supreme value of 5.14 MPa·m 1/2, which is improved nearly 39.67% compared with monolithic boron carbide materials. The fracture scanning electric microscope analysis of boron carbide-lanthanum boride composite material shows that, with the increase of the content of lanthanum boride, the interior station of monolithic boron carbide is changed. The crystallite arrangement is so compact that pores disappear gradually. The main fracture way of boron carbide-lanthanum boride composite material is intercrystalline rupture, while the transcrystalline rupture is minor, which is in accordance with fracture mechanism of ceramic material. It indicates that this change of fracture mode by the addition of lanthanum boride gives rise to the improvement of the fracture toughness.
基金Funded by the National Science Foundation of China Through Outstanding Youth Scientist Foundation (No. 59825102) and Science Foundation of Hubei Province(No. 98J028).
文摘Structural characteristics, chemical bonds and thermoelectric properties of Al-doped boron carbides are studied through calculations of various structural unit models by using a self-consistent-field discrete variation X. method. The calculations show that Al atom doped in boron carbide is in preference to substituting B or C atoms on the end of boron carbide chain, and then may occupy interstitial sites, but it is difficult for Al to substitute B or C atom in the centers of the chain or in the icosahedra. A representative structural unit containing an Al atom is [C - B -Al]-[B11C]-,while the structural unit without Al is [C-B-B(C)]- - [B11C]C+, and the coexistence of these two different structural units makes the electrical conductivity increased. As the covalent bond of Al-B or Al-C is weaker than that of B-B or B-C, the thermal conductivity decreases when Al is added into boron carbides. With the electrical conductivity increasing and the thermal conductivity decreases, Al doping has significant effect on thermoelectric properties of baron carbides.
基金the financial support received from the management of SSN。
文摘High velocity ballistic impact deformation behaviour of Titanium/GFRP Fiber Metal Laminates(FML)has been explored.Both single and multiple projectiles impact conditions were considered.Ti/GFRP FML targets were fabricated with addition of 5%and 10%weight percentage of boron carbide(B_(4)C)particles.Mechanical properties of Ti/GFRP FML targets were determined as per ASTM standards.High velocity ballistic experiments were conducted using Armour Piercing Projectile(APP)of diameter 7.62 mm and velocity ranging between 350 and 450 m/s.Depth of penetration of the projectile into the target was measured.The deformation behaviour of Ti/GFRP targets with and without the presence of ceramic powder(B_(4)C)was investigated.“Ductile hole growth”failure mode was observed for pure GFRP target when subjected to single projectile impact whereas“plugging”failure mode was noted for Ti/GFRP targets.The presence of B_(4)C(5%by weight)particles has significantly improved the ballistic resistance of the Ti/GFRP FML target by offering frictional resistance to the projectile penetration.Further addition(10%by weight)of B_(4)C has reduced the ballistic performance due to agglomeration.None of the targets showed‘brittle cracking’or‘fragmentation’failures.When compared to the published results of Aluminium(Al 1100/GFRP and Al 6061/GFRP)FMLs,Ti/GFRP FML showed lesser DoP which increases its potential application to aerospace industry.
文摘Different pre-heating of boron carbide particles for reinforcement and different processing conditions were studied in this work. Being one of the most cost-effective industrial methods, conventional melt stir-casting route was utilized.Result showed that the boron carbide particles distributed well for a suitable pre-heating temperature and processed in air.No reaction product was found at the A1-B4C interfaces at the resolution limit of SEM used in that way.
基金Financial assistance from Armament research board,New Delhi,India
文摘High strength-to-weight ratio of non-ferrous alloys, such as aluminium, magnesium and titanium alloys, are considered to be possible replacement of widely accepted steels in transportation and automobile sectors. Among these alloys, magnesium is self explosive and titanium is costlier, and aluminium is most likely to replace steels. Application of aluminium or its alloys is also thought of as an appropriate replacement in defence field, especially to enhance the easiness in mobility of combat vehicles while maintaining the same standard as that of conventional armour grade steels. Hence most of the investigations have been confined to aluminium or its alloys as base material and open an era of developing the newer composite materials to address the major limitation, i.e. tribological properties. The surface composites can be fabricated by incorporating the ceramic carbides like silicon carbide, carbides of transition metals and oxides of aluminium using surface modification techniques, such as high energy laser melt treatment, high energy electron beam irradiation and thermal spray process which are based on fusion route. These techniques yield the fusion related problems, such as interfacial reaction, pin holes, shrinkage cavities or voids and other casting related defects, and pave the way to need of an efficient technique which must be based on solid state. Recently developed friction stir processing technique was used in the present investigation for surface modification of AA7075 aluminum alloy, which is an alternative to steels. In the present investigation, 160 μm sized boron carbide powder was procured and was reduced to 60 μm and 30 μm using high energy ball mill. Subsequently these powders were used to fabricate the surface composites using friction stir processing.Ballistic performance testing as per the military standard(JIS.0108.01) was carried out. In the present work, an analytical method of predicting the ballistic behavior of surface composites was developed. This method was based on energy balance, i.e., the initial energy of impact is same as that of energy absorbed by multi layers. An attempt also has been made to validate the analytical results with the experimental findings. Variation between the analytical and experimental results may be accounted due to the assumptions considering such as isotropic behavior of target and shearing area of contact as cylindrical instead of conical interface As the analytical model yields the ballistic performance in the closer proximity of experimentally obtained, it can be considered to be an approximation to evaluate the ballistic performance of targets.
基金by the National Natural Science Foundation of China(52002299)。
文摘Reduced graphene oxide(rGO)enhanced B_(4)C ceramics was prepared by SPS sintering,the enhancement effect of rGO on the microstructure and mechanical properties of composites was studied through experiments and numerical simulation.The results show that the composite with 2wt%rGO has the best comprehensive mechanical properties.Compared with pure boron carbide,vickers hardness and bending strength are increased by 4.8%and 21.96%,respectively.The fracture toughness is improved by 25.71%.The microstructure observation shows that the improvement of mechanical properties is mainly attributed to the pullout and bridge mechanism of rGO and the crack deflection.Based on the cohesive force finite element method,the dynamic crack growth process of composites was simulated.The energy dissipation of B_(4)C/rGO multiphase ceramics during crack propagation was calculated and compared with that of pure boron carbide ceramics.The results show that the fracture energy dissipation can be effectively increased by adding graphene.
文摘Microstructure of plasma spray boron carbide coating was studied by SEM and TEM. Its physical, mechanical and electrical properties were measured. The results showed that high microhardness, modulus and low porosity of B4C coating were manufactured by plasma spray. It was lamellar packing and dense. The B4C coating examined here contained two principal structures and two impurity phase besides major phase. The relatively small value of Young's modulus, comparing with that of the bulk materials, is explained by porosity . The Fe impurity phase could account for the relatively high electrical conductivity of boron carbide coating by comparing with the general boron carbide materials.
基金Project supported by the National 863 (Grant No 2007AA03Z305)973 (Grant No 2007CB935503) programthe National Science Foundation of China (Grant Nos 60571045, 60620120443, Guo-JI He-Zuo)
文摘This paper reports that the large-scale single crystalline boron carbide nanobelts have been fabricated through a simple carbothermal reduction method with B/B2O3/C/Fe powder as precursors at 1100℃. Transmission electron microscopy and selected area electron diffraction characterizations show that the boron carbide nanobelt has a B4C rhomb-centred hexagonal structure with good crystallization. Electron energy loss spectroscopy analysis indicates that the nanobelt contains only B and C, and the atomic ratio of B to C is close to 4：1. High resolution transmission electron microscopy results show that the preferential growth direction of the nanobelt is [101]. A possible growth mechanism is also discussed.
基金Founded by the 863 High-Technology Research and Development Program of China(No.2011AA060104)
文摘We researched the electric heating property from butyl rubber-loaded boron carbide composite. The effects of boron carbide content on bulk resistivity, voltage-current characteristic, thermal conductivity and thermal stability of boron carbide / butyl rubber （IIR） polymer composite were introduced. The analysis results indicated that the bulk resistivity decreased greatly with increasing boron carbide content, and when boron carbide content reached to 60%, the bulk resistivity achieved the minimum. Accordingly, electric heating behavior of the composite is strongly dependent on boron carbide content as well as applied voltage. The content of boron carbide was found to be effective in achieving high thermal conductivity in composite systems. The thermal conductivity of the composite material with added boron carbide was improved nearly 20 times than that of the pure IIR. The thermal stability test showed that, compared with pure IIR, the thermal stable time of composites was markedly extended, which indicated that the boron carbide can significantly improve the thermal stability of boron carbide / IIR composite.
