In this study,a green and pollution-free multifunctional superhydrophobic paper-based material was prepared using a simple and efficient dipping method.The superhydrophobic paper with a water contact angle(WCA)of 160&...In this study,a green and pollution-free multifunctional superhydrophobic paper-based material was prepared using a simple and efficient dipping method.The superhydrophobic paper with a water contact angle(WCA)of 160°was prepared by attaching micro-and nanocomposite particles,made of stearic acid-modified chitosan and two kinds of titanium dioxide(TiO_(2))nanoparticles of different sizes,to a paper substrate.The surface morphology,elemental composition,and wetting properties of the coatings were examined using scanning electron microscopy(SEM),X-ray photoelectron spectroscopy(XPS),Fourier transform infrared spectroscopy(FT-IR),and contact angle measurements.Additionally,superhydrophobic coatings exhibited good self-cleaning properties,liquid repellency,ease of repair,and antifouling properties in organic solutions.展开更多
With lignite after vacuum drying as the raw material,a series of Zn-based sorbents were prepared by static impregnation,ultrasonic-assisted impregnation,bubbling-assisted impregnation and high-pressure impregnation.Th...With lignite after vacuum drying as the raw material,a series of Zn-based sorbents were prepared by static impregnation,ultrasonic-assisted impregnation,bubbling-assisted impregnation and high-pressure impregnation.The physical properties and the desulfurization performances of Zn-based sorbents were studied systematically by XRD,BET,AAS characterization techniques and the fixed-bed desulfurization evaluation apparatus.The sorbents obtained by high-pressure impregnation method have a larger specific surface area,pore volume and pore diameter comparing with other methods,which is conducive to the sulfidation reaction of hydrogen sulfide gas in the sorbent.The effects of pressure during the high-pressure impregnation and concentration of Zn(NO3)2 precursor solution on the sorbents properties and desulfurization behavior were investigated.The higher the impregnation pressure and the concentration of impregnation solution are,the greater the amount of the active components are uploaded.However,overhigh impregnation pressure can cause collapse and blocking of the carrier pore.The optimal operating condition of high-pressure impregnation method for preparing the sorbents was the impregnation pressure of 20 atm and the solution concentration of 41%.Under that condition,the sorbent had the best desulfurization ability with a sulfur capacity of 13.94 gS/100 gsorbent and a breakthrough time of 54 h.Its desulfurization precision and efficiency of removing H2S before sorbent breakthrough from the middle temperature gases of 400℃ can reach<5 ppm and>99%,respectively.Sorbents could be regenerated under the condition of 1 vol%O2,20 vol% H2O,0.5 vol% NH3,and N2balance gas.The regenerated sorbent could be used for repeated absorption of H2S with a slight decrease in desulfurization effect.展开更多
The Co-based catalysts were prepared with different cobalt acetate solutions. Effects of p H value were studied deeply on Fischer–Tropsch synthesis(FTS) through a semi-batch reactor. Among all impregnation solutions(...The Co-based catalysts were prepared with different cobalt acetate solutions. Effects of p H value were studied deeply on Fischer–Tropsch synthesis(FTS) through a semi-batch reactor. Among all impregnation solutions(water, butanol, amyl alcohol, acetic acid, nitric acid and ammonium nitrate), the catalyst prepared by NH_4NO_3 solution showed the highest catalytic activity due to its small particle size and high reduction degree. However, the catalyst with the smallest particle size derived from water as impregnation solution exhibited low activity as well as high methane selectivity since it was difficult to be reduced and inactive in FTS. According to FT-IR spectra results, the low intensity of absorbed CO on the catalyst prepared from water solution resulted in low FTS activity. Whereas, the high activity of catalysts prepared from NH_4NO_3 solution could be explained by the high intensity of absorbed CO on the catalysts.The cobalt species on the catalysts prepared under lower p H conditions exhibited smaller particle size distribution as well as lower CO conversion than those prepared at higher p H value.展开更多
In order to improve the properties of purging plugs and to prolong their service life,this work attempted to impregnate alumina-spinel castables for purging plugs in refining ladle with saturated magnesium chloride so...In order to improve the properties of purging plugs and to prolong their service life,this work attempted to impregnate alumina-spinel castables for purging plugs in refining ladle with saturated magnesium chloride solution under vacuum.After being impregnated for the first time,the specimens were treated in two different ways:(1)dried at 110℃for 24 h;(2)heated at 600℃for 3 h.Then they were impregnated for the second time.All specimens were heated at 1550℃for 3 h,then the cold properties and the high temperature properties were tested according to corresponding standards.Test results were compared and analyzed.The results show that:after being impregnated,the specimen have both better cold properties and high temperature properties,the microstructure analysis result proves that it is attributed to in situ formed spinel.However,because MgO produced by MgCl2-6H20 decomposing above 527℃can hydrate and destroy specimen microstructure,which can make the properties of specimens impregnated in the second way get worse.By comprehensive consideration,the first scheme way is more suitable.展开更多
A novel greener method to impregnate silver nanoparticles (AgNPs) into microcrystalline cellulose (MCC) by curry leaf (Murraya koenigii) extract mediated biological process is presented. The active reduction of silver...A novel greener method to impregnate silver nanoparticles (AgNPs) into microcrystalline cellulose (MCC) by curry leaf (Murraya koenigii) extract mediated biological process is presented. The active reduction of silver ions by curry leaf extract was explored for the in situ impregnation AgNPs into MCC. Transmission electron microscopy (TEM) analyses of MCC coated with AgNPs showed the formation of silver particle sizes in the range of 10-25 nm and have a spherical shape. Further the, EDS analysis of MCC/Ag nanocomposite confirms the formation of Ag structure on microcrystalline cellulose. Solvent casting of poly(lactic-acid) was used to produce composite films containing silver impregnated MCC aiming for antimicrobial applications.展开更多
An efficient technology of impregnation of carbonate crushed stone by oil-product based on SCF-impregnation process usage with propane/butane solvent was developed. Regular impregnation throughout the volume of crushe...An efficient technology of impregnation of carbonate crushed stone by oil-product based on SCF-impregnation process usage with propane/butane solvent was developed. Regular impregnation throughout the volume of crushed stone sample is achieved. As a result of the appliance of proposed technology, the humidity of the treated crushed stone samples decreased down to 0.54%.展开更多
In this paper, we deals with mechanical performance of resin impregnation with natural fiber and fiber reinforced composites. The effect of the addition of a rein impregnation process on static strength of the injecti...In this paper, we deals with mechanical performance of resin impregnation with natural fiber and fiber reinforced composites. The effect of the addition of a rein impregnation process on static strength of the injection molded composites was investigated by carrying out tensile and banding tests, followed by Scanning electron microscopy (SEM) observation of fiber surface and fracture surface of composites. The tensile strength of natural fiber and natural fiber reinforced composites with resin impregnation method increases with Polyvinyl alcohol (PVA) impregnation. In addition, Phenol resin impregnation recovers fiber tensile strength after alkali treatment. Resin impregnation causes decrease in contact surface area;however, it does not cause decrease in mechanical properties. Our results suggest that the using rein impregnation method has better effect on the mechanical properties of natural fiber reinforced Polypropylene (PP) composites.展开更多
D-72 resin supported nickel-copper catalysts prepared by solvated metal atom impreg-nation (SMAI) were studied by magnetic measurements and X-ray photoelectron spectro-scopy (XPS). The Ni particles on the catalysts ar...D-72 resin supported nickel-copper catalysts prepared by solvated metal atom impreg-nation (SMAI) were studied by magnetic measurements and X-ray photoelectron spectro-scopy (XPS). The Ni particles on the catalysts are very highly dispersed and displaysuperparamagnetic behaviour. Ni-Cu alloy clusters were found to be formed. The sur-face compositions are different from the bulk concentrations. In contrast with the surfaceenrichment in copper generally observed on conventional Ni-Cu catalysts, the surfaces ofthese catalysts are enriched in nickel. The nickel is in both zero and valent states, whilecopper is mainly in metallic state. Catalytic data show that the formation of Ni-Cu alloyclusters has a profound effect on the catalytic activities of the catalysts in the hydrogena-tion of furfural. The activity of the Ni:Cu ratio of one bimetallic catalysts is much higherthan that of the Ni or Cu monometallic catalyst.展开更多
Two kinds of small iron clusters supported on SiO2-200 (dehydroxylated at 200℃ and SiO2-600 (de-hydroxylated at 600℃) were prepared by Solvated Metal Atom Impregnation (SMAI) techniques. The iron atom precursor comp...Two kinds of small iron clusters supported on SiO2-200 (dehydroxylated at 200℃ and SiO2-600 (de-hydroxylated at 600℃) were prepared by Solvated Metal Atom Impregnation (SMAI) techniques. The iron atom precursor complex, bis (toluene) iron(0) formed in the metal atom reactor, was impregnated into SiO2 having different concentrations of surface hydroxyl groups to study the effect of surface hydroxylation on the crucial stage of iron cluster formation. Catalysts prepared in this way were characterized by THM, Mosbauer and chemisorption measurements, and the resules show that higher concentration of surface hydroxyl groups of SiO2-200 favours the formation of more positively charged support iron cluster Fen/SiO2-200 and the lower concentration of surface hydroxyl groups of SiO2-600 favours the formation of basically neutral supported iron cluster Fe2/SiO2-600. The measured results also indicate that the higher concentration of surface hydroxyl groups causes the precursor complex,bis(toluene) fron(0), to展开更多
This paper deals with the repair of dam-aged plain concrete and polymer cement concreteby impregnation with methyl methacrylate(MMA) or sulfur.The stress-strain(σ～ε)curves of the unaxial compression of the con-cret...This paper deals with the repair of dam-aged plain concrete and polymer cement concreteby impregnation with methyl methacrylate(MMA) or sulfur.The stress-strain(σ～ε)curves of the unaxial compression of the con-crete before and after repairing were given.Theresults indicate that the strength of damagedconcrete can be reinstated and even improved af-ter the concrete is impregnated with MMA orsulfur.The main mechanism of repairing is thatthe cracks,the original pores and microcracksare filled with MMA or sulfur,and the im-pregnant plays role in adhesion enhancement andreinforcement.展开更多
A model was deveIoped to investigate impregnation behavior of thermoplastic resin into filament bundle based on Darcy's law. Consolidation processes of unidirectional laminate were performed to evaluate the validi...A model was deveIoped to investigate impregnation behavior of thermoplastic resin into filament bundle based on Darcy's law. Consolidation processes of unidirectional laminate were performed to evaluate the validity of the model. Friction spun core yarns were used in the experiments with polypropylene fiber sheath and glass filament core. The processing conditions, such as temperature and pressure, and filament parameters were taken into consideration. A good agreement was found between theoretical prediction and experiment data.展开更多
To improve the mechanical properties of fast-growing Chinese fir(Cunnighamia lanceolate),expand its range of application,increase its value,and avoid the environmental pollution caused by impregnation with synthetic r...To improve the mechanical properties of fast-growing Chinese fir(Cunnighamia lanceolate),expand its range of application,increase its value,and avoid the environmental pollution caused by impregnation with synthetic resin,Chinese fir was impregnated with a shellac solution.Since the shellac solution was difficult to penetrate into fast-growing Chinese fir,so microwave pretreatment was used to irradiate the wood to improve the permeability.This study investigated the effects of four factors,including the content of moisture in the wood before it was microwaved,the chamber pressure of microwave,the time of microwaving and the vacuum impregnation on the mechanical properties of Chinese fir wood.When the moisture content of wood before microwave was approximately 50%–60%,after microwaving and impregnation,the ultimate strength in static bending(modulus of rupture[MOR])and strength in compression perpendicular to the grain(SCPG)of the wood increased significantly.A microwave time of 100 seconds was more effective at improving the MOR and SCPG of the wood.If the wood was microwaved for too short or long period of time,the microwave pretreatment was not effective.When the samples were immersed in shellac for a longer period,the MOR and SCPG of Chinese fir gradually increased,but when the wood was impregnated for more than 12 hours,the increases were not significant.After the shellac penetrated the Chinese fir wood,it spread on the inner wall surface of tracheid to form a shellac film and easily formed plug-like deposits in microcapillaries.The use of Fourier-transform infrared spectroscopy,scanning electron microscopy and scanning electron microscopy-energy dispersion x-ray indicated that the microwave pretreatment can destroy the pit membranes on tracheids and facilitate the ability of shellac to penetrate the channel.展开更多
Results of research of supercritical fluid CO2-impregnation process (the static mode) within a problem of synthesis of the palladium catalyst are given. The kinetics of process is characterized in the pressure range f...Results of research of supercritical fluid CO2-impregnation process (the static mode) within a problem of synthesis of the palladium catalyst are given. The kinetics of process is characterized in the pressure range from 15.0 to 35.0 MPa on temperatures 308.15?K, 313.15?K, 318.15?K, 323.15?K, 328.15?K and 333.15?K. Results of surface assessment and activity measurements of the catalyst samples synthesized by supercritical СO2-impregnation of aluminum oxide suggest competitiveness of the discussed approach in comparison to traditional methods.展开更多
Fortification of apple slices with t-resveratrol glucoside was obtained by vacuum impregnation (VI) of apple slices with a solution containing grape juice using response surface methodology (RSM). Three independent va...Fortification of apple slices with t-resveratrol glucoside was obtained by vacuum impregnation (VI) of apple slices with a solution containing grape juice using response surface methodology (RSM). Three independent variables of the VI process: vacuum pressure, application time and relaxation time, were coded at five levels in a central composite design. The VI-treated and dried apple slices were analyzed for t-resveratrol glucoside concentration and textural attributes (gradient and linear distance). Multiple response optimization revealed the following optimum VI condi-tions for the bioactive enrichment and improved textural quality of dried apple slices: vacuum pressure of 6 in. of Hg, application time of 10 min, and relaxation time of 22.5 min.展开更多
Viscose fiber templates(15 cm×15 cm×1 cm)were put into ZrOCl_(2) solutions of different concentrations(1,2 and 3 mol·L^(-1))and impregnated at different temperatures(20,40 and 60℃)for 20 h.After washin...Viscose fiber templates(15 cm×15 cm×1 cm)were put into ZrOCl_(2) solutions of different concentrations(1,2 and 3 mol·L^(-1))and impregnated at different temperatures(20,40 and 60℃)for 20 h.After washing,centrifugation and drying,ZrO_(2) fiber precursors were obtained.ZrO_(2) fibers were prepared by heat treatment of the precursors at different temperatures(600,800,1000 and 1200℃)for 2 h.The effects of the impregnation temperature,the impregnation solution concentration and the heat treatment temperature on the microstructure and the phase composition of the ZrO_(2) fibers were studied.The results show that with the increase of the impregnation temperature from 20℃to 60℃and the impregnation solution concentration increase from 1 mol·L^(-1) to 3 mol·L^(-1),the microstructure of fiber cross section changes from flat to cylindrical,and the average fiber diameter increases,indicating that the increase of the impregnation solution concentration and the impregnation temperature is beneficial to increasing the adsorption capacity of Zr4+on viscose fiber templates.After heat treatment,ZrO_(2) fiber mainly exists in the form of monoclinic ZrO_(2).With the increase of the heat treatment temperature,the grains in ZrO_(2) fibers become larger and the crystallinity degree increases,meanwhile the fiber surface undergoes a transition from smooth to small grains and then to cracks.展开更多
The steam-thermal method for refinery of highly-viscous oils and the process of propane-butane liquid extraction have been implemented for production of the impregnation material for carbon rock. The process of steam-...The steam-thermal method for refinery of highly-viscous oils and the process of propane-butane liquid extraction have been implemented for production of the impregnation material for carbon rock. The process of steam-thermal treatment has been carried out for highly-viscous oil from Ashalchinskoye accumulation with the “steam-oil” ratio changing from 1.1:1 to 1.4:1. The extraction process has been carried out at temperature T = 85°C and pressures from 4.5 to 8 MPa. Water absorption of carbonate rock has decreased to 0.34% as a result of SCF-impregnation process.展开更多
In order to develop a novel controlled-release material, we previously attempted to impregnate poly(L-lactide) (poly(L-LA)), poly(L-LA-ran-CL) (CL: ε-caprolactone) or poly(L-LA-ran-TEMC) (TEMC: tetramethylene carbona...In order to develop a novel controlled-release material, we previously attempted to impregnate poly(L-lactide) (poly(L-LA)), poly(L-LA-ran-CL) (CL: ε-caprolactone) or poly(L-LA-ran-TEMC) (TEMC: tetramethylene carbonate) with low boiling point, organic useful compounds using supercritical carbon dioxide (scCO2) as the solvent. In this work, the factors influencing impregnation of poly (L-LA) random copolymers with useful compounds were investigated under scCO2 using the copolymers previously used. The influence of temperature, pressure, and time on the impregnation contents of the useful compounds on the copolymers was evaluated. The polymer used, which is a base of this material, was poly(L-LA-ran-CL), poly(L-LA-ran-TEMC), or poly(L-LA-ran-DXO) (DXO: 1,5-dioxepan-2-one). Statistical random copolymers of L-LA with CL, TEMC, or DXO were synthesized using Sn(oct)2 as a catalyst at 150°C for 24 h without solvent. Preparation of the controlled-release materials was carried out using essential bark oil from Thujopsis dolabrata var. hondae and synthetic L-LA random copolymers as a base material under scCO2. The impregnation experiment, which investigated the influence of pressure, was conducted in the range of 10 to 20 MPa. The influence of temperature on impregnation was carried out at 40°C to 100°C. Impregnation time was varied from 1 to 5 h. The pressure of essential oil impregnated into poly(L-LA) random copolymers was the highest at 14 MPa. In the influence of temperature on impregnation, the amount of essential oil increased with increasing temperature.展开更多
Activated carbons (ACs) were prepared from a lignocellulosic-based waste material by a chemical impregnation method using KOH, NaOH or CaCl2 as the activating agent. These ACs were characterized by different technique...Activated carbons (ACs) were prepared from a lignocellulosic-based waste material by a chemical impregnation method using KOH, NaOH or CaCl2 as the activating agent. These ACs were characterized by different techniques such as N2 adsorption, FTIR, XRD and SEM. Electrostatic properties viz. pH and pHpzc of AC suspensions in aqueous media were measured. The concentration of surface oxygenated functional groups of the ACs was estimated following the Boehm titration method. Cyclic voltammetry was conducted in H2SO4 after fabricating two-electrode capacitor cells of the ACs. The correlation of AC surface chemistry and morphology with electrochemical performance (capacitance) of powdered electrodes is analyzed and discussed.展开更多
With the development of superconducting technology, the electrical performance of insulating materials is drawing increasing concern. This paper is devoted to investigating resin materials and aims to test the resin r...With the development of superconducting technology, the electrical performance of insulating materials is drawing increasing concern. This paper is devoted to investigating resin materials and aims to test the resin requirements of impregnating procedures and design curing molds. First, the samples are prepared, and then the power-frequency breakdown, lighting surges, relative dielectric constant, and loss angle tangent of the impregnation resin are measured at room temperature and liquid nitrogen temperature. We also present the testing reference for cryogenic and high-voltage insulating materials of superconducting power devices.展开更多
基金the financial support from the Key Research and Development Project of Shandong Province (2019GHY112040)National Natural Science Foundation of China (22078167)+4 种基金Youth Innovative Team Development Plan of Colleges and Universities in Shandong Province (2019KJC008)Shandong Province Major Innovation Project (2018CXGC1001)Foundation (No. XWZR201901) of the State Key Laboratory of Bio-based Material and Green Papermaking, Qilu University of TechnologyMajor Innovation Project of Qingdao West Coast (2019-27)Shandong Province Key Supporting Areas for Introducing Urgently Needed and Shortage of Talents Project-Key Technology Research and Development and Industrialization of Highly Water-Resistant Biomass-Based Materials。
文摘In this study,a green and pollution-free multifunctional superhydrophobic paper-based material was prepared using a simple and efficient dipping method.The superhydrophobic paper with a water contact angle(WCA)of 160°was prepared by attaching micro-and nanocomposite particles,made of stearic acid-modified chitosan and two kinds of titanium dioxide(TiO_(2))nanoparticles of different sizes,to a paper substrate.The surface morphology,elemental composition,and wetting properties of the coatings were examined using scanning electron microscopy(SEM),X-ray photoelectron spectroscopy(XPS),Fourier transform infrared spectroscopy(FT-IR),and contact angle measurements.Additionally,superhydrophobic coatings exhibited good self-cleaning properties,liquid repellency,ease of repair,and antifouling properties in organic solutions.
基金supported by the National Basic Research Program of China(2012CB723105)the National Natural Science Foundation of China(20976117)Shanxi Graduates Excellent Innovation Project of China(tyut-rc201018a)
文摘With lignite after vacuum drying as the raw material,a series of Zn-based sorbents were prepared by static impregnation,ultrasonic-assisted impregnation,bubbling-assisted impregnation and high-pressure impregnation.The physical properties and the desulfurization performances of Zn-based sorbents were studied systematically by XRD,BET,AAS characterization techniques and the fixed-bed desulfurization evaluation apparatus.The sorbents obtained by high-pressure impregnation method have a larger specific surface area,pore volume and pore diameter comparing with other methods,which is conducive to the sulfidation reaction of hydrogen sulfide gas in the sorbent.The effects of pressure during the high-pressure impregnation and concentration of Zn(NO3)2 precursor solution on the sorbents properties and desulfurization behavior were investigated.The higher the impregnation pressure and the concentration of impregnation solution are,the greater the amount of the active components are uploaded.However,overhigh impregnation pressure can cause collapse and blocking of the carrier pore.The optimal operating condition of high-pressure impregnation method for preparing the sorbents was the impregnation pressure of 20 atm and the solution concentration of 41%.Under that condition,the sorbent had the best desulfurization ability with a sulfur capacity of 13.94 gS/100 gsorbent and a breakthrough time of 54 h.Its desulfurization precision and efficiency of removing H2S before sorbent breakthrough from the middle temperature gases of 400℃ can reach<5 ppm and>99%,respectively.Sorbents could be regenerated under the condition of 1 vol%O2,20 vol% H2O,0.5 vol% NH3,and N2balance gas.The regenerated sorbent could be used for repeated absorption of H2S with a slight decrease in desulfurization effect.
基金financial support from the National Natural Science Foundation of China (21528302)Zhejiang Province Natural Science Foundation (LQ15B060004)
文摘The Co-based catalysts were prepared with different cobalt acetate solutions. Effects of p H value were studied deeply on Fischer–Tropsch synthesis(FTS) through a semi-batch reactor. Among all impregnation solutions(water, butanol, amyl alcohol, acetic acid, nitric acid and ammonium nitrate), the catalyst prepared by NH_4NO_3 solution showed the highest catalytic activity due to its small particle size and high reduction degree. However, the catalyst with the smallest particle size derived from water as impregnation solution exhibited low activity as well as high methane selectivity since it was difficult to be reduced and inactive in FTS. According to FT-IR spectra results, the low intensity of absorbed CO on the catalyst prepared from water solution resulted in low FTS activity. Whereas, the high activity of catalysts prepared from NH_4NO_3 solution could be explained by the high intensity of absorbed CO on the catalysts.The cobalt species on the catalysts prepared under lower p H conditions exhibited smaller particle size distribution as well as lower CO conversion than those prepared at higher p H value.
文摘In order to improve the properties of purging plugs and to prolong their service life,this work attempted to impregnate alumina-spinel castables for purging plugs in refining ladle with saturated magnesium chloride solution under vacuum.After being impregnated for the first time,the specimens were treated in two different ways:(1)dried at 110℃for 24 h;(2)heated at 600℃for 3 h.Then they were impregnated for the second time.All specimens were heated at 1550℃for 3 h,then the cold properties and the high temperature properties were tested according to corresponding standards.Test results were compared and analyzed.The results show that:after being impregnated,the specimen have both better cold properties and high temperature properties,the microstructure analysis result proves that it is attributed to in situ formed spinel.However,because MgO produced by MgCl2-6H20 decomposing above 527℃can hydrate and destroy specimen microstructure,which can make the properties of specimens impregnated in the second way get worse.By comprehensive consideration,the first scheme way is more suitable.
文摘A novel greener method to impregnate silver nanoparticles (AgNPs) into microcrystalline cellulose (MCC) by curry leaf (Murraya koenigii) extract mediated biological process is presented. The active reduction of silver ions by curry leaf extract was explored for the in situ impregnation AgNPs into MCC. Transmission electron microscopy (TEM) analyses of MCC coated with AgNPs showed the formation of silver particle sizes in the range of 10-25 nm and have a spherical shape. Further the, EDS analysis of MCC/Ag nanocomposite confirms the formation of Ag structure on microcrystalline cellulose. Solvent casting of poly(lactic-acid) was used to produce composite films containing silver impregnated MCC aiming for antimicrobial applications.
文摘An efficient technology of impregnation of carbonate crushed stone by oil-product based on SCF-impregnation process usage with propane/butane solvent was developed. Regular impregnation throughout the volume of crushed stone sample is achieved. As a result of the appliance of proposed technology, the humidity of the treated crushed stone samples decreased down to 0.54%.
文摘In this paper, we deals with mechanical performance of resin impregnation with natural fiber and fiber reinforced composites. The effect of the addition of a rein impregnation process on static strength of the injection molded composites was investigated by carrying out tensile and banding tests, followed by Scanning electron microscopy (SEM) observation of fiber surface and fracture surface of composites. The tensile strength of natural fiber and natural fiber reinforced composites with resin impregnation method increases with Polyvinyl alcohol (PVA) impregnation. In addition, Phenol resin impregnation recovers fiber tensile strength after alkali treatment. Resin impregnation causes decrease in contact surface area;however, it does not cause decrease in mechanical properties. Our results suggest that the using rein impregnation method has better effect on the mechanical properties of natural fiber reinforced Polypropylene (PP) composites.
文摘D-72 resin supported nickel-copper catalysts prepared by solvated metal atom impreg-nation (SMAI) were studied by magnetic measurements and X-ray photoelectron spectro-scopy (XPS). The Ni particles on the catalysts are very highly dispersed and displaysuperparamagnetic behaviour. Ni-Cu alloy clusters were found to be formed. The sur-face compositions are different from the bulk concentrations. In contrast with the surfaceenrichment in copper generally observed on conventional Ni-Cu catalysts, the surfaces ofthese catalysts are enriched in nickel. The nickel is in both zero and valent states, whilecopper is mainly in metallic state. Catalytic data show that the formation of Ni-Cu alloyclusters has a profound effect on the catalytic activities of the catalysts in the hydrogena-tion of furfural. The activity of the Ni:Cu ratio of one bimetallic catalysts is much higherthan that of the Ni or Cu monometallic catalyst.
文摘Two kinds of small iron clusters supported on SiO2-200 (dehydroxylated at 200℃ and SiO2-600 (de-hydroxylated at 600℃) were prepared by Solvated Metal Atom Impregnation (SMAI) techniques. The iron atom precursor complex, bis (toluene) iron(0) formed in the metal atom reactor, was impregnated into SiO2 having different concentrations of surface hydroxyl groups to study the effect of surface hydroxylation on the crucial stage of iron cluster formation. Catalysts prepared in this way were characterized by THM, Mosbauer and chemisorption measurements, and the resules show that higher concentration of surface hydroxyl groups of SiO2-200 favours the formation of more positively charged support iron cluster Fen/SiO2-200 and the lower concentration of surface hydroxyl groups of SiO2-600 favours the formation of basically neutral supported iron cluster Fe2/SiO2-600. The measured results also indicate that the higher concentration of surface hydroxyl groups causes the precursor complex,bis(toluene) fron(0), to
文摘This paper deals with the repair of dam-aged plain concrete and polymer cement concreteby impregnation with methyl methacrylate(MMA) or sulfur.The stress-strain(σ～ε)curves of the unaxial compression of the con-crete before and after repairing were given.Theresults indicate that the strength of damagedconcrete can be reinstated and even improved af-ter the concrete is impregnated with MMA orsulfur.The main mechanism of repairing is thatthe cracks,the original pores and microcracksare filled with MMA or sulfur,and the im-pregnant plays role in adhesion enhancement andreinforcement.
基金Funded by the Research Fund for the Doctoral Program of High Education
文摘A model was deveIoped to investigate impregnation behavior of thermoplastic resin into filament bundle based on Darcy's law. Consolidation processes of unidirectional laminate were performed to evaluate the validity of the model. Friction spun core yarns were used in the experiments with polypropylene fiber sheath and glass filament core. The processing conditions, such as temperature and pressure, and filament parameters were taken into consideration. A good agreement was found between theoretical prediction and experiment data.
基金the 2018 Forestry Science and Technology Research Project by Forestry Department of Fujian Province(No.2018-26)Science and Technology Innovation Special Fund Project of Fujian Agriculture and Forestry University(CXZX2019111S)+1 种基金National Natural Science Foundation of China(31971593,32071688)the Natural Science Foundation of Fujian Province Department of Science and Technology(2019J01386).
文摘To improve the mechanical properties of fast-growing Chinese fir(Cunnighamia lanceolate),expand its range of application,increase its value,and avoid the environmental pollution caused by impregnation with synthetic resin,Chinese fir was impregnated with a shellac solution.Since the shellac solution was difficult to penetrate into fast-growing Chinese fir,so microwave pretreatment was used to irradiate the wood to improve the permeability.This study investigated the effects of four factors,including the content of moisture in the wood before it was microwaved,the chamber pressure of microwave,the time of microwaving and the vacuum impregnation on the mechanical properties of Chinese fir wood.When the moisture content of wood before microwave was approximately 50%–60%,after microwaving and impregnation,the ultimate strength in static bending(modulus of rupture[MOR])and strength in compression perpendicular to the grain(SCPG)of the wood increased significantly.A microwave time of 100 seconds was more effective at improving the MOR and SCPG of the wood.If the wood was microwaved for too short or long period of time,the microwave pretreatment was not effective.When the samples were immersed in shellac for a longer period,the MOR and SCPG of Chinese fir gradually increased,but when the wood was impregnated for more than 12 hours,the increases were not significant.After the shellac penetrated the Chinese fir wood,it spread on the inner wall surface of tracheid to form a shellac film and easily formed plug-like deposits in microcapillaries.The use of Fourier-transform infrared spectroscopy,scanning electron microscopy and scanning electron microscopy-energy dispersion x-ray indicated that the microwave pretreatment can destroy the pit membranes on tracheids and facilitate the ability of shellac to penetrate the channel.
文摘Results of research of supercritical fluid CO2-impregnation process (the static mode) within a problem of synthesis of the palladium catalyst are given. The kinetics of process is characterized in the pressure range from 15.0 to 35.0 MPa on temperatures 308.15?K, 313.15?K, 318.15?K, 323.15?K, 328.15?K and 333.15?K. Results of surface assessment and activity measurements of the catalyst samples synthesized by supercritical СO2-impregnation of aluminum oxide suggest competitiveness of the discussed approach in comparison to traditional methods.
文摘Fortification of apple slices with t-resveratrol glucoside was obtained by vacuum impregnation (VI) of apple slices with a solution containing grape juice using response surface methodology (RSM). Three independent variables of the VI process: vacuum pressure, application time and relaxation time, were coded at five levels in a central composite design. The VI-treated and dried apple slices were analyzed for t-resveratrol glucoside concentration and textural attributes (gradient and linear distance). Multiple response optimization revealed the following optimum VI condi-tions for the bioactive enrichment and improved textural quality of dried apple slices: vacuum pressure of 6 in. of Hg, application time of 10 min, and relaxation time of 22.5 min.
文摘Viscose fiber templates(15 cm×15 cm×1 cm)were put into ZrOCl_(2) solutions of different concentrations(1,2 and 3 mol·L^(-1))and impregnated at different temperatures(20,40 and 60℃)for 20 h.After washing,centrifugation and drying,ZrO_(2) fiber precursors were obtained.ZrO_(2) fibers were prepared by heat treatment of the precursors at different temperatures(600,800,1000 and 1200℃)for 2 h.The effects of the impregnation temperature,the impregnation solution concentration and the heat treatment temperature on the microstructure and the phase composition of the ZrO_(2) fibers were studied.The results show that with the increase of the impregnation temperature from 20℃to 60℃and the impregnation solution concentration increase from 1 mol·L^(-1) to 3 mol·L^(-1),the microstructure of fiber cross section changes from flat to cylindrical,and the average fiber diameter increases,indicating that the increase of the impregnation solution concentration and the impregnation temperature is beneficial to increasing the adsorption capacity of Zr4+on viscose fiber templates.After heat treatment,ZrO_(2) fiber mainly exists in the form of monoclinic ZrO_(2).With the increase of the heat treatment temperature,the grains in ZrO_(2) fibers become larger and the crystallinity degree increases,meanwhile the fiber surface undergoes a transition from smooth to small grains and then to cracks.
文摘The steam-thermal method for refinery of highly-viscous oils and the process of propane-butane liquid extraction have been implemented for production of the impregnation material for carbon rock. The process of steam-thermal treatment has been carried out for highly-viscous oil from Ashalchinskoye accumulation with the “steam-oil” ratio changing from 1.1:1 to 1.4:1. The extraction process has been carried out at temperature T = 85°C and pressures from 4.5 to 8 MPa. Water absorption of carbonate rock has decreased to 0.34% as a result of SCF-impregnation process.
文摘In order to develop a novel controlled-release material, we previously attempted to impregnate poly(L-lactide) (poly(L-LA)), poly(L-LA-ran-CL) (CL: ε-caprolactone) or poly(L-LA-ran-TEMC) (TEMC: tetramethylene carbonate) with low boiling point, organic useful compounds using supercritical carbon dioxide (scCO2) as the solvent. In this work, the factors influencing impregnation of poly (L-LA) random copolymers with useful compounds were investigated under scCO2 using the copolymers previously used. The influence of temperature, pressure, and time on the impregnation contents of the useful compounds on the copolymers was evaluated. The polymer used, which is a base of this material, was poly(L-LA-ran-CL), poly(L-LA-ran-TEMC), or poly(L-LA-ran-DXO) (DXO: 1,5-dioxepan-2-one). Statistical random copolymers of L-LA with CL, TEMC, or DXO were synthesized using Sn(oct)2 as a catalyst at 150°C for 24 h without solvent. Preparation of the controlled-release materials was carried out using essential bark oil from Thujopsis dolabrata var. hondae and synthetic L-LA random copolymers as a base material under scCO2. The impregnation experiment, which investigated the influence of pressure, was conducted in the range of 10 to 20 MPa. The influence of temperature on impregnation was carried out at 40°C to 100°C. Impregnation time was varied from 1 to 5 h. The pressure of essential oil impregnated into poly(L-LA) random copolymers was the highest at 14 MPa. In the influence of temperature on impregnation, the amount of essential oil increased with increasing temperature.
文摘Activated carbons (ACs) were prepared from a lignocellulosic-based waste material by a chemical impregnation method using KOH, NaOH or CaCl2 as the activating agent. These ACs were characterized by different techniques such as N2 adsorption, FTIR, XRD and SEM. Electrostatic properties viz. pH and pHpzc of AC suspensions in aqueous media were measured. The concentration of surface oxygenated functional groups of the ACs was estimated following the Boehm titration method. Cyclic voltammetry was conducted in H2SO4 after fabricating two-electrode capacitor cells of the ACs. The correlation of AC surface chemistry and morphology with electrochemical performance (capacitance) of powdered electrodes is analyzed and discussed.
基金supported by the State Grid Scientific and Technological Project (Research on New Cryogenic Insulating Material and Superconducting Magnet Application,No.DG71-16-001)
文摘With the development of superconducting technology, the electrical performance of insulating materials is drawing increasing concern. This paper is devoted to investigating resin materials and aims to test the resin requirements of impregnating procedures and design curing molds. First, the samples are prepared, and then the power-frequency breakdown, lighting surges, relative dielectric constant, and loss angle tangent of the impregnation resin are measured at room temperature and liquid nitrogen temperature. We also present the testing reference for cryogenic and high-voltage insulating materials of superconducting power devices.
