A shaking table test for a bridge foundation reinforced by anti-slide piles on a silty clay landslide model with an inclined interlayer was performed.The deformation characteristics of the bridge foundation piles and ...A shaking table test for a bridge foundation reinforced by anti-slide piles on a silty clay landslide model with an inclined interlayer was performed.The deformation characteristics of the bridge foundation piles and anti-slide piles were analyzed in different loading conditions.The dynamic response law of a silty clay landslide with an inclined interlayer was summarized.The spacing between the rear anti-slide piles and bridge foundation should be reasonably controlled according to the seismic fortification requirements,to avoid the two peaks in the forced deformation of the bridge foundation piles.The“blocking effect”of the bridge foundation piles reduced the deformation of the forward anti-slide piles.The stress-strain response of silty clay was intensified as the vibration wave field appeared on the slope.Since the vibration intensified,the thrust distribution of the landslide underwent a process of shifting from triangle to inverted trapezoid,the difference in the acceleration response between the bearing platform and silty clay landslide tended to decrease,and the spectrum amplitude near the natural vibration frequency increased.The rear anti-slide piles were able to slow down the shear deformation of the soil in front of the piles and avoid excessive acceleration response of the bridge foundation piles.展开更多
Almost all sandstone reservoirs contain interlayers. The identification and characterization of these interlayers iscritical for minimizing the uncertainty associated with oilfield development and improving oil and ga...Almost all sandstone reservoirs contain interlayers. The identification and characterization of these interlayers iscritical for minimizing the uncertainty associated with oilfield development and improving oil and gas recovery.Identifying interlayers outside wells using identification methods based on logging data and machine learning isdifficult and seismic-based identification techniques are expensive. Herein, a numerical model based on seepageand well-testing theories is introduced to identify interlayers using transient pressure data. The proposed modelrelies on the open-source MATLAB Reservoir Simulation Toolbox. The effects of the interlayer thickness, position,and width on the pressure response are thoroughly investigated. A procedure for inverting interlayer parametersin the reservoir using the bottom-hole pressure is also proposed. This method uses only transient pressuredata during well testing and can effectively identify the interlayer distribution near the wellbore at an extremelylow cost. The reliability of the model is verified using effective oilfield examples.展开更多
High theoretical capacity and unique layered structures make MoS_(2)a promising lithium-ion battery anode material.However,the anisotropic ion transport in layered structures and the poor intrinsic conductivity of MoS...High theoretical capacity and unique layered structures make MoS_(2)a promising lithium-ion battery anode material.However,the anisotropic ion transport in layered structures and the poor intrinsic conductivity of MoS_(2)lead to unacceptable ion transport capability.Here,we propose in-situ construction of interlayer electrostatic repulsion caused by Co^(2+)substituting Mo^(4+)between MoS_(2)layers,which can break the limitation of interlayer van der Waals forces to fabricate monolayer MoS_(2),thus establishing isotropic ion transport paths.Simultaneously,the doped Co atoms change the electronic structure of monolayer MoS_(2),thus improving its intrinsic conductivity.Importantly,the doped Co atoms can be converted into Co nanoparticles to create a space charge region to accelerate ion transport.Hence,the Co-doped monolayer MoS_(2)shows ultrafast lithium ion transport capability in half/full cells.This work presents a novel route for the preparation of monolayer MoS_(2)and demonstrates its potential for application in fast-charging lithium-ion batteries.展开更多
In this study,HEA/AI composite interlayer was used to fabricate Ti/Mg bimetal composites by solidliquid compound casting process.The Al layer was prepared on the surface of TC4 alloy by hot dipping,and the FeCoNiCr HE...In this study,HEA/AI composite interlayer was used to fabricate Ti/Mg bimetal composites by solidliquid compound casting process.The Al layer was prepared on the surface of TC4 alloy by hot dipping,and the FeCoNiCr HEA layer was prepared by magnetron sputtering onto the Al layer.The influence of the HEA layer thickness and pouring temperature on interface evolution was investigated based on SEM observation and thermodynamic analysis.Results indicate that the sluggish diffusion effect of HEA can effectively inhibit the interfacial diffusion between Al and Mg,which is conducive to the formation of solid solution,especially when the thickness of HEA is 800 nm.With the increase of casting temperature from 720 ℃ to 730 ℃,740℃,and 750 ℃,α-Al(Mg),α-Al(Mg)+Al3Mg2,Al3Mg2+Al12Mg17,and Al12Mg17+δ-Mg are formed at the interface of Ti/Mg bimetal,respectively.When the thickness of the HEA layer is 800 nm and the pouring temperature is 720 ℃,the bonding strength of the Ti/Mg bimetal can reach the maximum of 93.6 MPa.展开更多
Strength-ductility trade-off is a common issue in Mg alloys. This work proposed that a synergistic enhancement of strength and ductility could be achieved through tuning interlayer dwell time(IDT) in the wire and arc ...Strength-ductility trade-off is a common issue in Mg alloys. This work proposed that a synergistic enhancement of strength and ductility could be achieved through tuning interlayer dwell time(IDT) in the wire and arc additive manufacturing(WAAM) process of Mg alloy.The thermal couples were used to monitor the thermal history during the WAAM process. Additionally, the effect of different IDTs on the microstructure characteristics and resultant mechanical properties of WAAM-processed Mg alloy thin-wall were investigated. The results showed that the stable temperature of the thin-wall component could reach 290 ℃ at IDT=0s, indicating that the thermal accumulation effect was remarkable. Consequently, unimodal coarse grains with an average size of 39.6 μm were generated, and the resultant room-temperature tensile property was poor. With the IDT extended to 60s, the thermal input and thermal dissipation reached a balance, and the stable temperature was only 170 ℃, closing to the initial temperature of the substrate. A refined grain structure with bimodal size distribution was obtained. The remelting zone had fine grains with the size of 15.2 μm, while the arc zone owned coarse grains with the size of 24.5 μm.The alternatively distributed coarse and fine grains lead to the elimination of strength-ductility trade-off. The ultimate tensile strength and elongation of the samples at IDT=60s are increased by 20.6 and 75.0% of those samples at IDT=0s, respectively. The findings will facilitate the development of additive manufacturing processes for advanced Mg alloys.展开更多
The article is devoted to the study of ecological and geochemical features of interlayer waters of the Dnieper–Donetsk aquifer system in Ukraine,used for the potable water supply of Kyiv.A wide range of methods was u...The article is devoted to the study of ecological and geochemical features of interlayer waters of the Dnieper–Donetsk aquifer system in Ukraine,used for the potable water supply of Kyiv.A wide range of methods was used,including Microsoft Excel,Statistica,and Attestat software packages,MapInfo Professional 6.5 and ArcGIS-ArcMap 9.3 programs;the method of mass spectrometry with inductively coupled plasma(ICP-MS)and GEMS software were performed.Monitoring study results(during 2007–2023)were analyzed for two interlayer aquifers—Cenomanian-Callovian groundwater complex and Bajocian aquifer.It was determined that the normalized value of mineralization increased with a decrease in water intake during 1980–2010,which indicates a relative increase in the content of mineral substances during longterm exploitation.A high negative correlation(Kcor.=-0.54 to-0.86)is also typical for normalized values of oxidizability,total hardness,pH,Ca,Mg,and Cl content.Comparative analysis of two different aquifers revealed that the macrocomponent composition of Bajocian aquifer remains stable,once for Cenomanian-Callovian groundwater complex,there is a tendency to decrease hydrogen carbonates and increase chlorides and sulfates,whereas the cation composition remains relatively stable.A significant increase(by 55%)of the total mineralization in the representative well located on the right bank of the Dnieper River was found.There is also a significant increase(by more than 5 times)in the iron content,which the authors associate with the unsatisfactory technical condition of the well casing pipes.Physico-chemical modeling of trace elements,performed for investigated aquifers,shows that both aquifers are characterized by the predominant migration of the following metals in the cationic form(aqua-ions):Ca,Mg,Na,Ba,Co,Cu,Mn,Ni,Sr,Zn.It was found that the predominant migration forms of metals in the studied interlayer waters are free uncomplexed ions,carbonate,and hydroxo complexes.展开更多
Soil salinization is a critical environmental issue restricting agricultural production.Deep return of straw to the soil as an interlayer (at 40 cm depth) has been a popular practice to alleviate salt stress.However,t...Soil salinization is a critical environmental issue restricting agricultural production.Deep return of straw to the soil as an interlayer (at 40 cm depth) has been a popular practice to alleviate salt stress.However,the legacy effects of straw added as an interlayer at different rates on soil organic carbon (SOC) and total nitrogen (TN) in saline soils still remain inconclusive.Therefore,a four-year (2015–2018) field experiment was conducted with four levels (i.e.,0,6,12and 18 Mg ha~(–1)) of straw returned as an interlayer.Compared with no straw interlayer (CK),straw addition increased SOC concentration by 14–32 and 11–57%in the 20–40 and 40–60 cm soil layers,respectively.The increases in soil TN concentration (8–22 and 6–34%in the 20–40 and 40–60 cm soil layers,respectively) were lower than that for SOC concentration,which led to increased soil C:N ratio in the 20–60 cm soil depth.Increases in SOC and TN concentrations in the 20–60 cm soil layer with straw addition led to a decrease in stratification ratios (0–20 cm:20–60 cm),which promoted uniform distributions of SOC and TN in the soil profile.Increases in SOC and TN concentrations were associated with soil salinity and moisture regulation and improved sunflower yield.Generally,compared with other treatments,the application of 12 Mg ha~(–1) straw had higher SOC,TN and C:N ratio,and lower soil stratification ratio in the2015–2017 period.The results highlighted that legacy effects of straw application as an interlayer were maintained for at least four years,and demonstrated that deep soil straw application had a great potential for improving subsoil fertility in salt-affected soils.展开更多
As an emerging member of the two-dimensional(2D)material family,V_(2)CT_(X)MXene shows great potential in the application of lithium-ion capacitors(LICs)due to its unique structure and excellent electrical conductivit...As an emerging member of the two-dimensional(2D)material family,V_(2)CT_(X)MXene shows great potential in the application of lithium-ion capacitors(LICs)due to its unique structure and excellent electrical conductivity.However,severe nanosheets stacking and intra-layer transport barriers have limited the further development of V_(2)CT_(X)MXene-based materials.Herein,we prepared Kions and–O functional group co-modified V_(2)CT_(X)MXene(VCT-K)and further incorporated it with single-walled carbon nanotube(SWCNT),obtaining freestanding V_(2)CT_(X)composite films(VCT-K@C)with the 3D conductive network.Significantly,K+ions were introduced into V_(2)CT_(X)MXene to stabilize the interlayer structure and prevent the aggregation of nanosheets,the terminal group of–O was controllably modified on the surface of MXene to improve the Li+ions storage reversible capacities and the SWCNT acted as the bridge between MXene nanosheets to opens up the channels for ion/electron transportation in the longitudinal direction.Benefited from the synergistic effect of VCT-K and SWCNT,the VCT-K@C exhibits superior reversible specific capacities of 671.8 mA h g^(-1)at 0.1 A g^(-1)and 318 mA h g^(-1)at 1.0 A g^(-1).Furthermore,the assembled LICs with VCT-K@C anode coupling activated carbon(AC)cathode deliver an outstanding power density of 19.0 kW kg^(-1)at 67.4 Wh kg^(-1),a high energy density of 140.5 Wh kg^(-1)at 94.8 W kg^(-1)and a stable capacitance retention of 86%after 6000 cycles at 10 A g^(-1).Such unique structures and excellent electrochemical properties are expected to pave the way for the large-scale application in LICs of MXene-based materials.展开更多
Inverted(p-i-n)perovskite solar cells(PerSCs)have attracted much attention owing to their low temperature processability,less hysteresis effect and easy integration as a subunit for the tandem device.The unsatisfactor...Inverted(p-i-n)perovskite solar cells(PerSCs)have attracted much attention owing to their low temperature processability,less hysteresis effect and easy integration as a subunit for the tandem device.The unsatisfactory interface contacts and energy level barrier between adjacent interlayers on the cathode side are one of the key challenges for the development of p-i-n PerSCs.Herein,perylene diimidebased(PDI)ionene polymer was synthesized and developed as a cathode interlayer(CIL)to enhance interface contact,reduce the energy level barrier and prevent the migration of I-ions.The compact PNPDI CIL with high conductivity and appropriate lowest unoccupied molecular orbital(LUMO)level,resulted in a high efficiency device(20.03%),which is higher than the control device with bathophenanthroline(Bphen)(19.48%).Bphen-based CIL shows better adjusting ability of the work function of cathode metal but exhibits poor film-forming property.So,the synergistic effect of 1+1>2 can be obtained by combining Bphen and PNPDI into one CIL.As expected,the device performance was further improved by using the mixed CIL of Bphen and PNPDI,and 21.46%power conversion efficiency(PCE)was achieved.What’s more,the compact and hydrophobic mixed CIL dramatically enhanced the resistance to I-ions and moisture,which led to much enhanced device stability.展开更多
The shear behavior of large-scale weak intercalation shear zones(WISZs)often governs the stability of foundations,rock slopes,and underground structures.However,due to their wide distribution,undulating morphology,com...The shear behavior of large-scale weak intercalation shear zones(WISZs)often governs the stability of foundations,rock slopes,and underground structures.However,due to their wide distribution,undulating morphology,complex fabrics,and varying degrees of contact states,characterizing the shear behavior of natural and complex large-scale WISZs precisely is challenging.This study proposes an analytical method to address this issue,based on geological fieldwork and relevant experimental results.The analytical method utilizes the random field theory and Kriging interpolation technique to simplify the spatial uncertainties of the structural and fabric features for WISZs into the spatial correlation and variability of their mechanical parameters.The Kriging conditional random field of the friction angle of WISZs is embedded in the discrete element software 3DEC,enabling activation analysis of WISZ C2 in the underground caverns of the Baihetan hydropower station.The results indicate that the activation scope of WISZ C2 induced by the excavation of underground caverns is approximately 0.5e1 times the main powerhouse span,showing local activation.Furthermore,the overall safety factor of WISZ C2 follows a normal distribution with an average value of 3.697.展开更多
The interlayer hybridization(IH)of van der Waals(vdW)materials is thought to be mostly associated with the unignorable interlayer overlaps of wavefunctions(t)in real space.Here,we develop a more fundamental understand...The interlayer hybridization(IH)of van der Waals(vdW)materials is thought to be mostly associated with the unignorable interlayer overlaps of wavefunctions(t)in real space.Here,we develop a more fundamental understanding of IH by introducing a new physical quantity,the IH admixture ratioα.Consequently,an exotic strategy of IH engineering in energy space can be proposed,i.e.,instead of changing t as commonly used,αcan be effectively tuned in energy space by changing the on-site energy difference(2Δ)between neighboring-layer states.In practice,this is feasible via reshaping the electrostatic potential of the surface by deposing a dipolar overlayer,e.g.,crystalline ice.Our first-principles calculations unveil that IH engineering via adjusting 2Δcan greatly tune interlayer optical transitions in transition-metal dichalcogenide bilayers,switch different types of Dirac surface states in Bi_(2)Se_(3)thin films,and control magnetic phase transition of charge density waves in 1H/1T-TaS_(2)bilayers,opening new opportunities to govern the fundamental optoelectronic,topological,and magnetic properties of vdW systems beyond the traditional interlayer distance or twisting engineering.展开更多
The practical application of Li metal anodes(LMAs)is limited by uncontrolled dendrite growth and side reactions.Herein,we propose a new friction-induced strategy to produce high-performance thin Li anode(Li@CFO).By vi...The practical application of Li metal anodes(LMAs)is limited by uncontrolled dendrite growth and side reactions.Herein,we propose a new friction-induced strategy to produce high-performance thin Li anode(Li@CFO).By virtue of the in situ friction reaction between fluoropolymer grease and Li strips during rolling,a robust organic/inorganic hybrid interlayer(lithiophilic LiF/LiC_(6)framework hybridized-CF_(2)-O-CF_(2)-chains)was formed atop Li metal.The derived interface contributes to reversible Li plating/stripping behaviors by mitigating side reactions and decreasing the solvation degree at the interface.The Li@CFO||Li@CFO symmetrical cell exhibits a remarkable lifespan for 5,600 h(1.0 mA cm^(-2)and 1.0 mAh cm^(-2))and 1,350 cycles even at a harsh condition(18.0 mA cm^(-2)and 3.0 mAh cm^(-2)).When paired with high-loading LiFePO4 cathodes,the full cell lasts over 450 cycles at 1C with a high-capacity retention of 99.9%.This work provides a new friction-induced strategy for producing high-performance thin LMAs.展开更多
For the compound sand body, the interlayer is an important factor affecting the adjustment of oil production structure and remaining oil distribution. According to the origin of argillaceous interlayer, the interlayer...For the compound sand body, the interlayer is an important factor affecting the adjustment of oil production structure and remaining oil distribution. According to the origin of argillaceous interlayer, the interlayer is divided into three types, including barriers between two single layers, intercalations between two single sands and intercalations in a single sand. In this study, the upper limit of physical properties of interlayer was obtained by analyzing the relationship between physical parameters and production index per-meter. The discriminant index and comprehensive discriminant chart of interlayer were obtained by grey correlation method, which realize the quantitative identification of different types of interlayer. The intercalations between two single sands in the target area are distributed almost in the whole area, which is one of the most important factors influencing the mining effect of compound sand, so the planar distribution is mainly aimed at it. Firstly, through cross-well comparison, we summarize three interlayer patterns, then establish their forward modeling, so as to obtain the vertical seismic characteristics of different patterns. Secondly, according to the thickness of intercalations between two single sands, we take the top of bottom sand as the baseline, extract the average amplitude attribute from the upper and lower 3 ms, then, according to the seismic section and planar characteristics of the well, the interlayer structures represented by different seismic section and planar characteristics are summarized. Finally, starting from the real drilling interlayer of the well, the planar spread of interlay can be obtained according to their variation trend and distribution.展开更多
The interlayer contact condition of asphalt pavement has a significant impact on stress transfer and energy dissipation with adjacent layers,so a model considering the bonding condition of adjacent layers is introduce...The interlayer contact condition of asphalt pavement has a significant impact on stress transfer and energy dissipation with adjacent layers,so a model considering the bonding condition of adjacent layers is introduced for evaluating the structural response of asphalt pavement.The pavement structure,the material characterization with temperature,the interlayer contact bonding model,the types of bond failure,and the prediction method of pavement life are described in detail.Results show that the transversely tensile strains at the top of asphalt pavement under the condition of high temperature were easy to cause the top-down cracking outside the edge of the dual tire.The bonding failure has a significant influence on strains at the bottom of the surface course with the condition of high temperature,especially,the longitudinally tensile strains would increase obviously as the disengaging area between the surface course of asphalt pavement and the base layer increases.Finally,it is proved that the surface course is vulnerable to form deformations and cause damage under the combined action of low speed and high temperature.展开更多
Taking the fluvial reservoir of the Neogene Minghuazhen Formation in Bozhong S oilfield in China as an example, a detailed study of the interlayer in the reservoir was conducted. From the perspective of sedimentary ge...Taking the fluvial reservoir of the Neogene Minghuazhen Formation in Bozhong S oilfield in China as an example, a detailed study of the interlayer in the reservoir was conducted. From the perspective of sedimentary genesis of the interlayer, three types of genesis of the interlayer are summarized and analyzed, namely, fine grain sediment in the inter peak channel, suspended sediment in the post flood channel, and abandoned channel sediment. At the same time, combined with seismic waveform analysis, the distribution characteristics and morphology of the interlayer in complex fluvial facies oilfield are carefully depicted, and the horizontal well optimization implementation is guided based on the planar and three-dimensional spatial distribution characteristics of the interlayer. This method enriches the characterization technology of interlayer in offshore oilfields, and has important guiding significance for the overall evaluation and development research of complex fluvial facies oilfields.展开更多
Using an MTS 815 testing machine,the deformation and failure behavior of a rock-coal-rock combined body containing a weak coal interlayer has been investigated and described in this paper.Uniaxial loading leads to the...Using an MTS 815 testing machine,the deformation and failure behavior of a rock-coal-rock combined body containing a weak coal interlayer has been investigated and described in this paper.Uniaxial loading leads to the appearance of mixed cracks in the coal body which induce instability and lead to bursts in coal.If the mixed crack propagates at a sufficiently high speed to carry enough energy to damage the roof rock,then coal and rock bursts may occur-this is the main mechanism whereby coal bumps or coal and rock bursts occur after excavation unloading.With increasing confining pressure,the failure strength of a rock-coal-rock combined body gradually increases,and the failure mechanism of the coal interlayer also changes,from mixed crack damage under low confining pressures,to parallel crack damage under medium confining pressures,and finally to single shear crack damage or integral mixed section damage under high confining pressures.In general,it is shown that a weak coal interlayer changes the form of overall coal damage in a rock-coal-rock combined body and reduces the overall stability of a coal body.Therefore,the whole failure behavior of a rock-coal-rock combined body in large cutting height working faces is controlled by these mechanisms.展开更多
The complex distribution of gas hydrate in sediments makes understanding the mechanical properties of hydrate-bearing sediments a challenging task.The mechanical behaviors of hydrate-bearing interlayered sediments are...The complex distribution of gas hydrate in sediments makes understanding the mechanical properties of hydrate-bearing sediments a challenging task.The mechanical behaviors of hydrate-bearing interlayered sediments are still poorly known.A series of triaxial shearing tests were conducted to investigate the strength parameters and deformation properties of methane hydrate-bearing interlayered sediments at the effective pressure of 1 MPa.The results indicate that the stress-strain curves of hydrate-bearing interlayered sediments are significantly different from that of hydrate-bearing sediments.The peak strength,Young's modulus,initial yielding modulus,and failure mode are deeply affected by the methane hydrate distribution.The failure behaviors and mechanism of strain softening and hardening patterns of the interlayered specimens are more complicated than those of the integrated specimens.This study compares the different mechanical behaviors between integrated and interlayered specimens containing gas hydrate,which can serve as a reference for the prediction and analysis of the deformation behaviors of natural gas hydrate reservoirs.展开更多
The basic principle of friction welding is intermetallic bonding at the stage of super plasticity attained with self-generating heat due to friction and finishing at upset pressure. Now the dissimilar metal joints are...The basic principle of friction welding is intermetallic bonding at the stage of super plasticity attained with self-generating heat due to friction and finishing at upset pressure. Now the dissimilar metal joints are especially popular in defense, aerospace, automobile, bio-medical,refinery and nuclear engineerings. In friction welding, some special alloys with dual phase are not joined successfully due to poor bonding strength. The alloy surfaces after bonding also have metallurgical changes in the line of interfacing. The reported research work in this area is scanty. Although the sound weld zone of direct bonding between Tie6Ale4 V and SS304 L was obtained though many trials, the joint was not successful. In this paper, the friction welding characteristics between Tie6Ale4 V and SS304 L into which pure oxygen free copper(OFC) was introduced as interlayer were investigated. Boxe Behnken design was used to minimize the number of experiments to be performed. The weld joint was analyzed for its mechanical strength. The highest tensile strength between Tie6Ale4 V and SS304 L between which pure copper was used as insert metal was acquired. Micro-structural analysis and elemental analysis were carried out by EDS, and the formation of intermetallic compound at the interface was identified by XRD analysis.展开更多
By applying experimental method, the bolt stress and supporting mechanism is studied during the deformation process of a rock mass containing a weak interlayer. The force measuring bolt is installed manually and instr...By applying experimental method, the bolt stress and supporting mechanism is studied during the deformation process of a rock mass containing a weak interlayer. The force measuring bolt is installed manually and instrumented five pairs of symmetrical strain gauges. The experimental results show that the fully grouted bolt suffers tensile, compressive, bending and shear stress at the same time. The bolt stress evolution is closely related to the deformation stages of the rock mass which are very gradually varying stage, gradually varying stage at the pre-peak and suddenly varying stage at the post peak stage.The axial compressive stress in the bolt is mainly induced by the moment. Thus, in most cases the axial compressive stress is distributed on one side of the bolt. For axial stresses, induced by the axial force and the bending moment at the post-peak stage, three types of changing are observed, viz. increasingincreasing type, decreasing-increasing type and increasing-decreasing type. The stress characteristics of the bolt section in the weak interlayer are significantly different from those in the hard rock. The failure models of the anchored bolt are tensile failure and shear failure, respectively. The bolt not only provides constraints on the free surface of the rock mass, but also resists the axial and lateral loading by the bending moment. This study provides valuable guidelines for bolting support design and its safety assessment.展开更多
The rheological behavior of a soft interlayer is critical to understanding slope stability, which is closely related to the water content of the soft interlayer. This study used the soft interlayer of the Permian Maok...The rheological behavior of a soft interlayer is critical to understanding slope stability, which is closely related to the water content of the soft interlayer. This study used the soft interlayer of the Permian Maokou Formation in Southwest China as an example to perform ring shear creep tests with different water content amounts. The effect of water content on the creep properties of the soft interlayer was analyzed, and a new shear rheological model was established. This research produced several findings. First, the ring shear creep deformation of the soft interlayer samples varied with the water content and the maximum instantaneous shear strain increment occurred near the saturated water content. As the water content increased, the cumulative creep increment of the samples increased. Second, the water content significantly affected the long-term strength of the soft interlayer, which decreased with the increase of water content, exhibiting a negative linear correlation. Third, a constitutive equation for the new rheological model was derived, and through fitting of the ring shear creep test data, the validity and applicability of the constitutive equation were proven. This study has developed an important foundation for studying the long-term deformation characteristics of a soft interlayer with varying water content.展开更多
基金Sichuan Science and Technology Program under Grant No.2023NSFSC0894Major Project of the Science and Technology Research and Development Program of the Ministry of Railways of China under Grant No.Z2012-061。
文摘A shaking table test for a bridge foundation reinforced by anti-slide piles on a silty clay landslide model with an inclined interlayer was performed.The deformation characteristics of the bridge foundation piles and anti-slide piles were analyzed in different loading conditions.The dynamic response law of a silty clay landslide with an inclined interlayer was summarized.The spacing between the rear anti-slide piles and bridge foundation should be reasonably controlled according to the seismic fortification requirements,to avoid the two peaks in the forced deformation of the bridge foundation piles.The“blocking effect”of the bridge foundation piles reduced the deformation of the forward anti-slide piles.The stress-strain response of silty clay was intensified as the vibration wave field appeared on the slope.Since the vibration intensified,the thrust distribution of the landslide underwent a process of shifting from triangle to inverted trapezoid,the difference in the acceleration response between the bearing platform and silty clay landslide tended to decrease,and the spectrum amplitude near the natural vibration frequency increased.The rear anti-slide piles were able to slow down the shear deformation of the soil in front of the piles and avoid excessive acceleration response of the bridge foundation piles.
文摘Almost all sandstone reservoirs contain interlayers. The identification and characterization of these interlayers iscritical for minimizing the uncertainty associated with oilfield development and improving oil and gas recovery.Identifying interlayers outside wells using identification methods based on logging data and machine learning isdifficult and seismic-based identification techniques are expensive. Herein, a numerical model based on seepageand well-testing theories is introduced to identify interlayers using transient pressure data. The proposed modelrelies on the open-source MATLAB Reservoir Simulation Toolbox. The effects of the interlayer thickness, position,and width on the pressure response are thoroughly investigated. A procedure for inverting interlayer parametersin the reservoir using the bottom-hole pressure is also proposed. This method uses only transient pressuredata during well testing and can effectively identify the interlayer distribution near the wellbore at an extremelylow cost. The reliability of the model is verified using effective oilfield examples.
基金financially supported by Shenzhen Key Laboratory of Advanced Energy Storage(No.ZDSYS20220401141000001)the Research Grants Council of the Hong Kong Special Administrative Region,China(Project No.R6005-20)。
文摘High theoretical capacity and unique layered structures make MoS_(2)a promising lithium-ion battery anode material.However,the anisotropic ion transport in layered structures and the poor intrinsic conductivity of MoS_(2)lead to unacceptable ion transport capability.Here,we propose in-situ construction of interlayer electrostatic repulsion caused by Co^(2+)substituting Mo^(4+)between MoS_(2)layers,which can break the limitation of interlayer van der Waals forces to fabricate monolayer MoS_(2),thus establishing isotropic ion transport paths.Simultaneously,the doped Co atoms change the electronic structure of monolayer MoS_(2),thus improving its intrinsic conductivity.Importantly,the doped Co atoms can be converted into Co nanoparticles to create a space charge region to accelerate ion transport.Hence,the Co-doped monolayer MoS_(2)shows ultrafast lithium ion transport capability in half/full cells.This work presents a novel route for the preparation of monolayer MoS_(2)and demonstrates its potential for application in fast-charging lithium-ion batteries.
基金financial supports from the National Natural Science Foundation of China (No. 51875062)China Postdoctoral Science Foundation (No. 2021M700567)。
文摘In this study,HEA/AI composite interlayer was used to fabricate Ti/Mg bimetal composites by solidliquid compound casting process.The Al layer was prepared on the surface of TC4 alloy by hot dipping,and the FeCoNiCr HEA layer was prepared by magnetron sputtering onto the Al layer.The influence of the HEA layer thickness and pouring temperature on interface evolution was investigated based on SEM observation and thermodynamic analysis.Results indicate that the sluggish diffusion effect of HEA can effectively inhibit the interfacial diffusion between Al and Mg,which is conducive to the formation of solid solution,especially when the thickness of HEA is 800 nm.With the increase of casting temperature from 720 ℃ to 730 ℃,740℃,and 750 ℃,α-Al(Mg),α-Al(Mg)+Al3Mg2,Al3Mg2+Al12Mg17,and Al12Mg17+δ-Mg are formed at the interface of Ti/Mg bimetal,respectively.When the thickness of the HEA layer is 800 nm and the pouring temperature is 720 ℃,the bonding strength of the Ti/Mg bimetal can reach the maximum of 93.6 MPa.
基金the support from Projects of Major Innovation Platforms for Scientific and Technological and Local Transformation of Scientific and Technological Achievements of Xi’an (No.20GXSF0003)the Higher Education Institution Discipline Innovation and Intelligence Base of Shaanxi Provincial (No.S2021-ZC-GXYZ0011)National Natural Science Foundation of China (Grants No.51801154)。
文摘Strength-ductility trade-off is a common issue in Mg alloys. This work proposed that a synergistic enhancement of strength and ductility could be achieved through tuning interlayer dwell time(IDT) in the wire and arc additive manufacturing(WAAM) process of Mg alloy.The thermal couples were used to monitor the thermal history during the WAAM process. Additionally, the effect of different IDTs on the microstructure characteristics and resultant mechanical properties of WAAM-processed Mg alloy thin-wall were investigated. The results showed that the stable temperature of the thin-wall component could reach 290 ℃ at IDT=0s, indicating that the thermal accumulation effect was remarkable. Consequently, unimodal coarse grains with an average size of 39.6 μm were generated, and the resultant room-temperature tensile property was poor. With the IDT extended to 60s, the thermal input and thermal dissipation reached a balance, and the stable temperature was only 170 ℃, closing to the initial temperature of the substrate. A refined grain structure with bimodal size distribution was obtained. The remelting zone had fine grains with the size of 15.2 μm, while the arc zone owned coarse grains with the size of 24.5 μm.The alternatively distributed coarse and fine grains lead to the elimination of strength-ductility trade-off. The ultimate tensile strength and elongation of the samples at IDT=60s are increased by 20.6 and 75.0% of those samples at IDT=0s, respectively. The findings will facilitate the development of additive manufacturing processes for advanced Mg alloys.
基金financially supported by budget thematic of M.P.Semenenko Institute of Geochemistry,Mineralogy and Ore Formation of the NAS of Ukraine and the State Institution‘‘The Institute of Environmental Geochemistry of the National Academy of Sciences of Ukraine’’。
文摘The article is devoted to the study of ecological and geochemical features of interlayer waters of the Dnieper–Donetsk aquifer system in Ukraine,used for the potable water supply of Kyiv.A wide range of methods was used,including Microsoft Excel,Statistica,and Attestat software packages,MapInfo Professional 6.5 and ArcGIS-ArcMap 9.3 programs;the method of mass spectrometry with inductively coupled plasma(ICP-MS)and GEMS software were performed.Monitoring study results(during 2007–2023)were analyzed for two interlayer aquifers—Cenomanian-Callovian groundwater complex and Bajocian aquifer.It was determined that the normalized value of mineralization increased with a decrease in water intake during 1980–2010,which indicates a relative increase in the content of mineral substances during longterm exploitation.A high negative correlation(Kcor.=-0.54 to-0.86)is also typical for normalized values of oxidizability,total hardness,pH,Ca,Mg,and Cl content.Comparative analysis of two different aquifers revealed that the macrocomponent composition of Bajocian aquifer remains stable,once for Cenomanian-Callovian groundwater complex,there is a tendency to decrease hydrogen carbonates and increase chlorides and sulfates,whereas the cation composition remains relatively stable.A significant increase(by 55%)of the total mineralization in the representative well located on the right bank of the Dnieper River was found.There is also a significant increase(by more than 5 times)in the iron content,which the authors associate with the unsatisfactory technical condition of the well casing pipes.Physico-chemical modeling of trace elements,performed for investigated aquifers,shows that both aquifers are characterized by the predominant migration of the following metals in the cationic form(aqua-ions):Ca,Mg,Na,Ba,Co,Cu,Mn,Ni,Sr,Zn.It was found that the predominant migration forms of metals in the studied interlayer waters are free uncomplexed ions,carbonate,and hydroxo complexes.
基金funded by the National Natural Science Foundation of China (31871584)the Agricultural Science and Technology Innovation Program, Chinese Academy of Agricultural Sciences (CAAS-ZDRW202201)+2 种基金the Fundamental Research Funds for Central Non-profit Scientific Institution, China (1610132020011)the “Open the list” in charge of the Science and Technology Project of Ordos, Center for Agro-pastoral Ecology and Resource Conservation of Ordos City, Inner Mongolia, China (JBGS2021-001)the Inner Mongolia Autonomous Region Research Project (2021EEDSCXSFQZD011)。
文摘Soil salinization is a critical environmental issue restricting agricultural production.Deep return of straw to the soil as an interlayer (at 40 cm depth) has been a popular practice to alleviate salt stress.However,the legacy effects of straw added as an interlayer at different rates on soil organic carbon (SOC) and total nitrogen (TN) in saline soils still remain inconclusive.Therefore,a four-year (2015–2018) field experiment was conducted with four levels (i.e.,0,6,12and 18 Mg ha~(–1)) of straw returned as an interlayer.Compared with no straw interlayer (CK),straw addition increased SOC concentration by 14–32 and 11–57%in the 20–40 and 40–60 cm soil layers,respectively.The increases in soil TN concentration (8–22 and 6–34%in the 20–40 and 40–60 cm soil layers,respectively) were lower than that for SOC concentration,which led to increased soil C:N ratio in the 20–60 cm soil depth.Increases in SOC and TN concentrations in the 20–60 cm soil layer with straw addition led to a decrease in stratification ratios (0–20 cm:20–60 cm),which promoted uniform distributions of SOC and TN in the soil profile.Increases in SOC and TN concentrations were associated with soil salinity and moisture regulation and improved sunflower yield.Generally,compared with other treatments,the application of 12 Mg ha~(–1) straw had higher SOC,TN and C:N ratio,and lower soil stratification ratio in the2015–2017 period.The results highlighted that legacy effects of straw application as an interlayer were maintained for at least four years,and demonstrated that deep soil straw application had a great potential for improving subsoil fertility in salt-affected soils.
基金funded by the National Natural Science Foundation of China(Grant Nos.22005167 and 21905152)the Shandong Provincial Natural Science Foundation of China(Grant Nos.ZR2020QB125 and ZR2020MB045)+1 种基金the China Postdoctoral Science Foundation(Grant Nos.2021M693256,2021T140687 and 2022M713249)the Qingdao Postdoctoral Applied Research Project and the Youth Innovation Team Project for Talent Introduction and Cultivation in Universities of Shandong Province。
文摘As an emerging member of the two-dimensional(2D)material family,V_(2)CT_(X)MXene shows great potential in the application of lithium-ion capacitors(LICs)due to its unique structure and excellent electrical conductivity.However,severe nanosheets stacking and intra-layer transport barriers have limited the further development of V_(2)CT_(X)MXene-based materials.Herein,we prepared Kions and–O functional group co-modified V_(2)CT_(X)MXene(VCT-K)and further incorporated it with single-walled carbon nanotube(SWCNT),obtaining freestanding V_(2)CT_(X)composite films(VCT-K@C)with the 3D conductive network.Significantly,K+ions were introduced into V_(2)CT_(X)MXene to stabilize the interlayer structure and prevent the aggregation of nanosheets,the terminal group of–O was controllably modified on the surface of MXene to improve the Li+ions storage reversible capacities and the SWCNT acted as the bridge between MXene nanosheets to opens up the channels for ion/electron transportation in the longitudinal direction.Benefited from the synergistic effect of VCT-K and SWCNT,the VCT-K@C exhibits superior reversible specific capacities of 671.8 mA h g^(-1)at 0.1 A g^(-1)and 318 mA h g^(-1)at 1.0 A g^(-1).Furthermore,the assembled LICs with VCT-K@C anode coupling activated carbon(AC)cathode deliver an outstanding power density of 19.0 kW kg^(-1)at 67.4 Wh kg^(-1),a high energy density of 140.5 Wh kg^(-1)at 94.8 W kg^(-1)and a stable capacitance retention of 86%after 6000 cycles at 10 A g^(-1).Such unique structures and excellent electrochemical properties are expected to pave the way for the large-scale application in LICs of MXene-based materials.
基金supported by the National Key Research and Development Program of China(2019YFA0705201)the Heilongjiang Provincial Postdoctoral Science Foundation(LBHTZ0604)the CAS Key Laboratory of Renewable Energy,Guangzhou Institute of Energy Conversion(E229kf0901)。
文摘Inverted(p-i-n)perovskite solar cells(PerSCs)have attracted much attention owing to their low temperature processability,less hysteresis effect and easy integration as a subunit for the tandem device.The unsatisfactory interface contacts and energy level barrier between adjacent interlayers on the cathode side are one of the key challenges for the development of p-i-n PerSCs.Herein,perylene diimidebased(PDI)ionene polymer was synthesized and developed as a cathode interlayer(CIL)to enhance interface contact,reduce the energy level barrier and prevent the migration of I-ions.The compact PNPDI CIL with high conductivity and appropriate lowest unoccupied molecular orbital(LUMO)level,resulted in a high efficiency device(20.03%),which is higher than the control device with bathophenanthroline(Bphen)(19.48%).Bphen-based CIL shows better adjusting ability of the work function of cathode metal but exhibits poor film-forming property.So,the synergistic effect of 1+1>2 can be obtained by combining Bphen and PNPDI into one CIL.As expected,the device performance was further improved by using the mixed CIL of Bphen and PNPDI,and 21.46%power conversion efficiency(PCE)was achieved.What’s more,the compact and hydrophobic mixed CIL dramatically enhanced the resistance to I-ions and moisture,which led to much enhanced device stability.
基金support from the Key Projects of the Yalong River Joint Fund of the National Natural Science Foundation of China(Grant No.U1865203)the Innovation Team of Changjiang River Scientific Research Institute(Grant Nos.CKSF2021715/YT and CKSF2023305/YT)。
文摘The shear behavior of large-scale weak intercalation shear zones(WISZs)often governs the stability of foundations,rock slopes,and underground structures.However,due to their wide distribution,undulating morphology,complex fabrics,and varying degrees of contact states,characterizing the shear behavior of natural and complex large-scale WISZs precisely is challenging.This study proposes an analytical method to address this issue,based on geological fieldwork and relevant experimental results.The analytical method utilizes the random field theory and Kriging interpolation technique to simplify the spatial uncertainties of the structural and fabric features for WISZs into the spatial correlation and variability of their mechanical parameters.The Kriging conditional random field of the friction angle of WISZs is embedded in the discrete element software 3DEC,enabling activation analysis of WISZ C2 in the underground caverns of the Baihetan hydropower station.The results indicate that the activation scope of WISZ C2 induced by the excavation of underground caverns is approximately 0.5e1 times the main powerhouse span,showing local activation.Furthermore,the overall safety factor of WISZ C2 follows a normal distribution with an average value of 3.697.
基金supported by the National Key R&D Program of China(Grant No.2022YFA1504000)the National Natural Science Foundation of China(Grant Nos.12088101,U2230402)+1 种基金the Tianjin Natural Science Foundation(Grant No.20JCZDJC00750)the Deutsche Forschungsgemeinschaft(DFG)(Grant No.EXC 2077)。
文摘The interlayer hybridization(IH)of van der Waals(vdW)materials is thought to be mostly associated with the unignorable interlayer overlaps of wavefunctions(t)in real space.Here,we develop a more fundamental understanding of IH by introducing a new physical quantity,the IH admixture ratioα.Consequently,an exotic strategy of IH engineering in energy space can be proposed,i.e.,instead of changing t as commonly used,αcan be effectively tuned in energy space by changing the on-site energy difference(2Δ)between neighboring-layer states.In practice,this is feasible via reshaping the electrostatic potential of the surface by deposing a dipolar overlayer,e.g.,crystalline ice.Our first-principles calculations unveil that IH engineering via adjusting 2Δcan greatly tune interlayer optical transitions in transition-metal dichalcogenide bilayers,switch different types of Dirac surface states in Bi_(2)Se_(3)thin films,and control magnetic phase transition of charge density waves in 1H/1T-TaS_(2)bilayers,opening new opportunities to govern the fundamental optoelectronic,topological,and magnetic properties of vdW systems beyond the traditional interlayer distance or twisting engineering.
基金This work was supported by the National Natural Science Foundation of China(U1904216 and U22A20141)the Natural Science Foundation of Changsha City(kq2208258).
文摘The practical application of Li metal anodes(LMAs)is limited by uncontrolled dendrite growth and side reactions.Herein,we propose a new friction-induced strategy to produce high-performance thin Li anode(Li@CFO).By virtue of the in situ friction reaction between fluoropolymer grease and Li strips during rolling,a robust organic/inorganic hybrid interlayer(lithiophilic LiF/LiC_(6)framework hybridized-CF_(2)-O-CF_(2)-chains)was formed atop Li metal.The derived interface contributes to reversible Li plating/stripping behaviors by mitigating side reactions and decreasing the solvation degree at the interface.The Li@CFO||Li@CFO symmetrical cell exhibits a remarkable lifespan for 5,600 h(1.0 mA cm^(-2)and 1.0 mAh cm^(-2))and 1,350 cycles even at a harsh condition(18.0 mA cm^(-2)and 3.0 mAh cm^(-2)).When paired with high-loading LiFePO4 cathodes,the full cell lasts over 450 cycles at 1C with a high-capacity retention of 99.9%.This work provides a new friction-induced strategy for producing high-performance thin LMAs.
文摘For the compound sand body, the interlayer is an important factor affecting the adjustment of oil production structure and remaining oil distribution. According to the origin of argillaceous interlayer, the interlayer is divided into three types, including barriers between two single layers, intercalations between two single sands and intercalations in a single sand. In this study, the upper limit of physical properties of interlayer was obtained by analyzing the relationship between physical parameters and production index per-meter. The discriminant index and comprehensive discriminant chart of interlayer were obtained by grey correlation method, which realize the quantitative identification of different types of interlayer. The intercalations between two single sands in the target area are distributed almost in the whole area, which is one of the most important factors influencing the mining effect of compound sand, so the planar distribution is mainly aimed at it. Firstly, through cross-well comparison, we summarize three interlayer patterns, then establish their forward modeling, so as to obtain the vertical seismic characteristics of different patterns. Secondly, according to the thickness of intercalations between two single sands, we take the top of bottom sand as the baseline, extract the average amplitude attribute from the upper and lower 3 ms, then, according to the seismic section and planar characteristics of the well, the interlayer structures represented by different seismic section and planar characteristics are summarized. Finally, starting from the real drilling interlayer of the well, the planar spread of interlay can be obtained according to their variation trend and distribution.
基金supported by the Scientific Research Program Funded by Shaanxi Provincial Education Department(Program No.21JK0830)Shaanxi Provincial Natural Science Foundation Research Project(Program No.2022JM-166).
文摘The interlayer contact condition of asphalt pavement has a significant impact on stress transfer and energy dissipation with adjacent layers,so a model considering the bonding condition of adjacent layers is introduced for evaluating the structural response of asphalt pavement.The pavement structure,the material characterization with temperature,the interlayer contact bonding model,the types of bond failure,and the prediction method of pavement life are described in detail.Results show that the transversely tensile strains at the top of asphalt pavement under the condition of high temperature were easy to cause the top-down cracking outside the edge of the dual tire.The bonding failure has a significant influence on strains at the bottom of the surface course with the condition of high temperature,especially,the longitudinally tensile strains would increase obviously as the disengaging area between the surface course of asphalt pavement and the base layer increases.Finally,it is proved that the surface course is vulnerable to form deformations and cause damage under the combined action of low speed and high temperature.
文摘Taking the fluvial reservoir of the Neogene Minghuazhen Formation in Bozhong S oilfield in China as an example, a detailed study of the interlayer in the reservoir was conducted. From the perspective of sedimentary genesis of the interlayer, three types of genesis of the interlayer are summarized and analyzed, namely, fine grain sediment in the inter peak channel, suspended sediment in the post flood channel, and abandoned channel sediment. At the same time, combined with seismic waveform analysis, the distribution characteristics and morphology of the interlayer in complex fluvial facies oilfield are carefully depicted, and the horizontal well optimization implementation is guided based on the planar and three-dimensional spatial distribution characteristics of the interlayer. This method enriches the characterization technology of interlayer in offshore oilfields, and has important guiding significance for the overall evaluation and development research of complex fluvial facies oilfields.
基金supported by the Special Funds for Major State Basic Research Project(Nos.2011CB201201 and 2010CB732002)the National Natural Science Foundation of China(Nos.11102225and51374215)the National Excellent Doctoral Dissertation of China(No.201030)
文摘Using an MTS 815 testing machine,the deformation and failure behavior of a rock-coal-rock combined body containing a weak coal interlayer has been investigated and described in this paper.Uniaxial loading leads to the appearance of mixed cracks in the coal body which induce instability and lead to bursts in coal.If the mixed crack propagates at a sufficiently high speed to carry enough energy to damage the roof rock,then coal and rock bursts may occur-this is the main mechanism whereby coal bumps or coal and rock bursts occur after excavation unloading.With increasing confining pressure,the failure strength of a rock-coal-rock combined body gradually increases,and the failure mechanism of the coal interlayer also changes,from mixed crack damage under low confining pressures,to parallel crack damage under medium confining pressures,and finally to single shear crack damage or integral mixed section damage under high confining pressures.In general,it is shown that a weak coal interlayer changes the form of overall coal damage in a rock-coal-rock combined body and reduces the overall stability of a coal body.Therefore,the whole failure behavior of a rock-coal-rock combined body in large cutting height working faces is controlled by these mechanisms.
基金supported by the National Natural Science Foundation of China (No. 41976074)National Key Research and Development Plan (No. 2017YFC030 7600)+2 种基金the Taishan Scholar Special Experts Project (No. ts201712079)Qingdao National Laboratory for Marine Science and Technology (No. QNLM2016ORP0207)the Graduate School Innovation Program of China University of Petroleum (East China) (No. YCX2019020)
文摘The complex distribution of gas hydrate in sediments makes understanding the mechanical properties of hydrate-bearing sediments a challenging task.The mechanical behaviors of hydrate-bearing interlayered sediments are still poorly known.A series of triaxial shearing tests were conducted to investigate the strength parameters and deformation properties of methane hydrate-bearing interlayered sediments at the effective pressure of 1 MPa.The results indicate that the stress-strain curves of hydrate-bearing interlayered sediments are significantly different from that of hydrate-bearing sediments.The peak strength,Young's modulus,initial yielding modulus,and failure mode are deeply affected by the methane hydrate distribution.The failure behaviors and mechanism of strain softening and hardening patterns of the interlayered specimens are more complicated than those of the integrated specimens.This study compares the different mechanical behaviors between integrated and interlayered specimens containing gas hydrate,which can serve as a reference for the prediction and analysis of the deformation behaviors of natural gas hydrate reservoirs.
文摘The basic principle of friction welding is intermetallic bonding at the stage of super plasticity attained with self-generating heat due to friction and finishing at upset pressure. Now the dissimilar metal joints are especially popular in defense, aerospace, automobile, bio-medical,refinery and nuclear engineerings. In friction welding, some special alloys with dual phase are not joined successfully due to poor bonding strength. The alloy surfaces after bonding also have metallurgical changes in the line of interfacing. The reported research work in this area is scanty. Although the sound weld zone of direct bonding between Tie6Ale4 V and SS304 L was obtained though many trials, the joint was not successful. In this paper, the friction welding characteristics between Tie6Ale4 V and SS304 L into which pure oxygen free copper(OFC) was introduced as interlayer were investigated. Boxe Behnken design was used to minimize the number of experiments to be performed. The weld joint was analyzed for its mechanical strength. The highest tensile strength between Tie6Ale4 V and SS304 L between which pure copper was used as insert metal was acquired. Micro-structural analysis and elemental analysis were carried out by EDS, and the formation of intermetallic compound at the interface was identified by XRD analysis.
基金support of the National Basic Research 973 Program of China (No.2013CB036003)the National Natural Science Foundation of China (No.51374198)the National Natural Science Foundation young investigator grant program of China (Nos.51204163,51504247,and 51404255)
文摘By applying experimental method, the bolt stress and supporting mechanism is studied during the deformation process of a rock mass containing a weak interlayer. The force measuring bolt is installed manually and instrumented five pairs of symmetrical strain gauges. The experimental results show that the fully grouted bolt suffers tensile, compressive, bending and shear stress at the same time. The bolt stress evolution is closely related to the deformation stages of the rock mass which are very gradually varying stage, gradually varying stage at the pre-peak and suddenly varying stage at the post peak stage.The axial compressive stress in the bolt is mainly induced by the moment. Thus, in most cases the axial compressive stress is distributed on one side of the bolt. For axial stresses, induced by the axial force and the bending moment at the post-peak stage, three types of changing are observed, viz. increasingincreasing type, decreasing-increasing type and increasing-decreasing type. The stress characteristics of the bolt section in the weak interlayer are significantly different from those in the hard rock. The failure models of the anchored bolt are tensile failure and shear failure, respectively. The bolt not only provides constraints on the free surface of the rock mass, but also resists the axial and lateral loading by the bending moment. This study provides valuable guidelines for bolting support design and its safety assessment.
基金supported by the National Natural Science Foundation of China(Grant No.41521001)the Natural Science Foundation of Hubei Province(Grant No.2018CFB385)
文摘The rheological behavior of a soft interlayer is critical to understanding slope stability, which is closely related to the water content of the soft interlayer. This study used the soft interlayer of the Permian Maokou Formation in Southwest China as an example to perform ring shear creep tests with different water content amounts. The effect of water content on the creep properties of the soft interlayer was analyzed, and a new shear rheological model was established. This research produced several findings. First, the ring shear creep deformation of the soft interlayer samples varied with the water content and the maximum instantaneous shear strain increment occurred near the saturated water content. As the water content increased, the cumulative creep increment of the samples increased. Second, the water content significantly affected the long-term strength of the soft interlayer, which decreased with the increase of water content, exhibiting a negative linear correlation. Third, a constitutive equation for the new rheological model was derived, and through fitting of the ring shear creep test data, the validity and applicability of the constitutive equation were proven. This study has developed an important foundation for studying the long-term deformation characteristics of a soft interlayer with varying water content.
