In the separation process with a jig washer, an accurate on-line measurement of loose status of a jigging bed is essential for a successful control of coal quality and loose status is difficult to measure on-line dire...In the separation process with a jig washer, an accurate on-line measurement of loose status of a jigging bed is essential for a successful control of coal quality and loose status is difficult to measure on-line directly in industrial process situations. So a soft-sensor technology is needed for this purpose. The soft-sensor model is developed in the experiment by an adaptive neuro-fuzzy inference system （ANFIS） which has a remarkable ability of learning and generalization. Based on the analysis of the technologic mechanism of jigging bed, the structure of the ANFIS is established to build the soft-sensor model of loose status estimation. The ANFIS is trained by a hybrid learning algorithm. Finally, the simulation results and comparison analysis are presented, which indicate that the ANFIS has better abilities of learning and generalization than the RBF and the BP networks. Thus, it is possible that the loose status of the jigging bed can be estimated on-line bv using ANFIS.展开更多
To make backfilling body meet strength requirement,physical-chemical evaluation and proportioning tests were conducted on several backfilling materials.Jigging sands,#32.5 cement and fly ash were determined as backfil...To make backfilling body meet strength requirement,physical-chemical evaluation and proportioning tests were conducted on several backfilling materials.Jigging sands,#32.5 cement and fly ash were determined as backfilling aggregate,binding material and modified material,respectively.An optimized proportion of backfilling materials with a solid mass fraction of 78%and cement:fly ash:jigging sands mass ratio of 1:2:14,was suggested to Jiangan Pyrite Mine,China.The slurry made by optimized proportion produced obvious shear thinning phenomena,and was confirmed as paste-like slurry.To analyze its rheological characteristics,L-type pipeline test and Haake VT550 rotational viscometer test were conducted.Bingham and Casson fluid models were applied to several paste-like slurry samples to simulate flow and stress states;Casson fluid model was proved to have better simulation effect on paste-like slurry with shear thinning phenomena;rheological parameters of backfilling slurry made by suggested proportion were measured.Initial yield stress,average apparent viscosity and limiting viscosity are 55.35 Pa,1.216 Pa-s and 0.48 Pa-s,respectively.Compared with Bingham fluid model,Casson fluid model has a better simulation effect on paste-like slurry with shear thinning phenomena,through calculating the residual standard deviations.展开更多
The concept of the flowing film jigging was first applied to the flowing film concentration area.The flowingfilm jigging function is an important element of the new process,in jection-flowing film centrifugation(IFFC)...The concept of the flowing film jigging was first applied to the flowing film concentration area.The flowingfilm jigging function is an important element of the new process,in jection-flowing film centrifugation(IFFC),for separating and recovering minerals of ultrafine sizes.展开更多
The Magnetohydrostatic Jigging Separation(MHSJS)is a method which makes use of the vibration of the solid particles obtained by applying a periodically changing magnetic Held to cause a periodically changing magnetic ...The Magnetohydrostatic Jigging Separation(MHSJS)is a method which makes use of the vibration of the solid particles obtained by applying a periodically changing magnetic Held to cause a periodically changing magnetic bouyancy to achieve an efficient separation of materials.展开更多
The laws of motion of particle groups in a jigging process are studied. These describe the macroscopic phenomena that occur during jigging. During jigging the heavier and bigger particles concentrate at the bed bottom...The laws of motion of particle groups in a jigging process are studied. These describe the macroscopic phenomena that occur during jigging. During jigging the heavier and bigger particles concentrate at the bed bottom while lighter and smaller particles move to the upper part of the bed. Particles with equivalent properties tend to concentrate at a certain position centered around the inherent height of their distribution. The particle distribution variance gradually diminishes to some asymptotic value. The state equation group of the jigging bed is deduced and a calculation method, called the λ value judgment method, is proposed. The method is used to calculate the layer number and the inherent height of each particle group. A mathematical expression for the particle distribution variance is also given.展开更多
This paper proposes the expression of the jigging bed porosity based on the jumping height of the jigging bed and water wave. This kind of expression can help to realize the jigging process automation and intelligence...This paper proposes the expression of the jigging bed porosity based on the jumping height of the jigging bed and water wave. This kind of expression can help to realize the jigging process automation and intelligence. The computer detection system is also developed.展开更多
This paper analyzes the detection means of the feeding coal in the jigging process, and puts forward a fuzzy control system of the variable construction in order to control the feeding coal. The fuzzy control system c...This paper analyzes the detection means of the feeding coal in the jigging process, and puts forward a fuzzy control system of the variable construction in order to control the feeding coal. The fuzzy control system consists of three parts: bang-bang control, keep control and fuzzy control.展开更多
To address the alignment and measuring force problem in the segmenting-stitching technique for the circularity metrology of small cylindrical workpieces(diameter less than 1.5 mm and length less than 10 mm),a magnet c...To address the alignment and measuring force problem in the segmenting-stitching technique for the circularity metrology of small cylindrical workpieces(diameter less than 1.5 mm and length less than 10 mm),a magnet combination jig method is proposed.A small round magnet is attached between the round magnetic jig and small cylinder,and the other end of the small cylindrical workpiece is attached to some cylindrical magnets.Thus,the smaller cylinder can be put in the V-groove and measured successfully with the magnet combination.For verifying the advantage of the magnet combination jig,four measurement quality evaluations are proposed:the circumferential deviation of neighbor arc contours,radial deviation of neighbor arc contours,angle of inclination between the V-groove and small cylinder,and curvature of the obtained arc.The results show that the matching coefficient is enhanced by 98%,the Euclidean distance of overlap parts of neighbor arc contours is reduced by 68%,the position error is reduced 27%,and the average curvature of the arc contours is improved.It can be concluded that the measuring quality can be enhanced prominently by this magnet combination method for the segmenting-stitching method.展开更多
Considerable amounts of coal particles are accumulated in the tailing dams of washing plants which can make serious environmental problems. Recovery of these particles from tailings has economically and environmentall...Considerable amounts of coal particles are accumulated in the tailing dams of washing plants which can make serious environmental problems. Recovery of these particles from tailings has economically and environmentally several advantages. Maintaining natural resources and reducing discharges to the dams are the most important ones. This study was examined the possibility to recover coal particles from a tailing dam with 56.29% ash content by using series of processing techniques. For this purpose, gravity separation （jig, shaking table and spiral） and flotation tests were conducted to upgrade products. Based the optimum value of these processing methods, a flowsheet was designed to increase the rate of recovery for a wide range of coal particles. Results indicated that the designed circuit can recover over 90% of value coal particles and reduce ash content of product to less than 14%. These results can potentially be used for designing an industrial operation as a recycling plant and an appropriate instance for other areas to reduce the environmental issues of coal tailing dams.展开更多
Catch per unit of eff ort(CPUE) data can display spatial autocorrelation. However, most of the CPUE standardization methods developed so far assumes independency of observations for the dependent variable, which is of...Catch per unit of eff ort(CPUE) data can display spatial autocorrelation. However, most of the CPUE standardization methods developed so far assumes independency of observations for the dependent variable, which is often invalid. In this study, we collected data of two fisheries, squid jigging fishery and mackerel trawl fishery. We used standard generalized linear model(GLM) and spatial GLMs to compare the impact of spatial autocorrelation on CPUE standardization for different fisheries. We found that spatialGLMs perform better than standard-GLM for both fisheries. The overestimation of precision of CPUE estimates was observed in both fisheries. Moran's I was used to quantify the level of autocorrelation for the two fisheries. The results show that autocorrelation in mackerel trawl fishery was much stronger than that in squid jigging fishery. According to the results of this paper, we highly recommend to account for spatial autocorrelation when using GLM to standardize CPUE data derived from commercial fisheries.展开更多
Beneficiation of coal of -4.76 mm + 3 mm size fraction was investigated in a laboratory model Denver jig.Process variables were studied to analyze their effect on the performance of jig in terms of yield and ash conte...Beneficiation of coal of -4.76 mm + 3 mm size fraction was investigated in a laboratory model Denver jig.Process variables were studied to analyze their effect on the performance of jig in terms of yield and ash content of clean coal. Three-factor three-level Box-Behnken design of experiments with response surface methodology(RSM) was employed to understand the performance behavior of jig. From the study, the bed height was found to be the most significant parameter affecting the yield and ash content of clean coal. It was possible to reduce the ash content from 24.32% in feed to an ash content of 16.55% in clean coal at 2 L/min water flow rate and 10 min jigging time. Influence of operating variables of the jig on responses was presented and discussed in 3D surface plots. The developed model was found to be significant within the range of parameters under investigation with correlation of co-efficient values as 0.99(yield) and 0.98(ash).展开更多
Hills Like White Elephants is a short story by Ernest Hemingway.It is a story about an American man and a pregnant girl.As the protagonist,Jig is considered as a submissive woman who has no definite views of her own.T...Hills Like White Elephants is a short story by Ernest Hemingway.It is a story about an American man and a pregnant girl.As the protagonist,Jig is considered as a submissive woman who has no definite views of her own.This paper attempts to analyze the changes of Jig's inner thought during the forty minutes of waiting the train.In addition to how the girl has grown up from a weak and dependent character into a brave and independent female after the painful struggle in the helpless and hopeless states under the great pressure of the man.展开更多
AIM: To compare the postoperative mechanical alignment achieved after total knee arthroplasty(TKA) using computer tomography(CT) based patient specific blocks(PSB) to conventional instruments(CI).METHODS: Total 80 kne...AIM: To compare the postoperative mechanical alignment achieved after total knee arthroplasty(TKA) using computer tomography(CT) based patient specific blocks(PSB) to conventional instruments(CI).METHODS: Total 80 knees were included in the study, with 40 knees in both the groups operated using PSB and CI. All the knees were performed by a single surgeon using the same cruciate sacrificing implants. In our study we used CT based PSB to compare with CI. Postoperative mechanical femoro-tibial angle(MFT angle) was measured on long leg x-rays using picture archiving and communication system(PACS). We compared mechanical alignment achieved using PSB and CI in TKA using statistical analysis.RESULTS: The PSB group(group 1) included 17 females and seven males while in CI group(group 2) there were 15 females and eight males. The mean age of patients in group 1 was 60.5 years and in group 2 it was 60.2 years. The mean postoperative MFT angle measured on long-leg radiographs in group 1 was 178.23°(SD = 2.67°, range: 171.9° to 182.5°) while in group 2, the mean MFT angle was 175.73°(SD = 3.62°, range: 166.0° to 179.8°). There was significant improvement in postoperative mechanical alignment(P value = 0.001), in PSB group compared to CI. Number of outliers were also found to be less in group operated with PSB(7 Knee) compared to those operated with CI(17 Knee).CONCLUSION: PSB improve mechanical alignment after total knee arthroplasty, compared to CI. This may lead to lower rates of revision in the PSB based TKA as compared to the conventional instrumentation.展开更多
This paper mainly describes that loose of jig bed affects jig's separation effect, and the corresponding fuzzy rules were built. Using the evaluating index of jig's separation effect--imperfection (I) and tota...This paper mainly describes that loose of jig bed affects jig's separation effect, and the corresponding fuzzy rules were built. Using the evaluating index of jig's separation effect--imperfection (I) and total misplaced material (Cz), it evaluates status of loose of jig bed by fuzzy inference system. Experimental simulation and applications in practice prove the method's feasibility.展开更多
The air bag deformation data were obtained by high-speed dynamic videos experiments. Based on gas–liquid flow VOF model, dynamic mesh technique and deformation data, numerical simulations for different structure mode...The air bag deformation data were obtained by high-speed dynamic videos experiments. Based on gas–liquid flow VOF model, dynamic mesh technique and deformation data, numerical simulations for different structure models were achieved, and the law of water motion and influencing factors were analyzed.The results show that the flow in the length direction of the jig is smooth, and second pulsation appears in the separation time and forms the secondary separation. The installation position of screen and the number of air bags have a great influence on the uniformity of flow and velocity. The screen height cannot be too low to avoid forming the unstable flow. At the same time, the screen height cannot be too high, otherwise water velocity will be too small and was unable to provide enough power. At the height of 1.4m,velocity unevenness is minimum and the best uniform flow can be obtained. Compared with double air bags, there are the following features of single air bag: water flow is not smooth, the time achieving the maximum velocity is too long, maximum velocity is smaller, and overall effect is worse than double air bags.展开更多
基金Project 70533050 supported by National Natural Science Foundation of China, 2005037225 by Postdoctoral Science Foundation of China, [2004]300 byPostdoctoral Science Foundation of Jiangsu Province, and OC 4465 bu Young Science Foundation of China University of Mining & Technology
文摘In the separation process with a jig washer, an accurate on-line measurement of loose status of a jigging bed is essential for a successful control of coal quality and loose status is difficult to measure on-line directly in industrial process situations. So a soft-sensor technology is needed for this purpose. The soft-sensor model is developed in the experiment by an adaptive neuro-fuzzy inference system （ANFIS） which has a remarkable ability of learning and generalization. Based on the analysis of the technologic mechanism of jigging bed, the structure of the ANFIS is established to build the soft-sensor model of loose status estimation. The ANFIS is trained by a hybrid learning algorithm. Finally, the simulation results and comparison analysis are presented, which indicate that the ANFIS has better abilities of learning and generalization than the RBF and the BP networks. Thus, it is possible that the loose status of the jigging bed can be estimated on-line bv using ANFIS.
基金Project(2012BAC09B02)supported by the National Science and Technology Pillar Program during the 12th Five-Year Plan Period,China
文摘To make backfilling body meet strength requirement,physical-chemical evaluation and proportioning tests were conducted on several backfilling materials.Jigging sands,#32.5 cement and fly ash were determined as backfilling aggregate,binding material and modified material,respectively.An optimized proportion of backfilling materials with a solid mass fraction of 78%and cement:fly ash:jigging sands mass ratio of 1:2:14,was suggested to Jiangan Pyrite Mine,China.The slurry made by optimized proportion produced obvious shear thinning phenomena,and was confirmed as paste-like slurry.To analyze its rheological characteristics,L-type pipeline test and Haake VT550 rotational viscometer test were conducted.Bingham and Casson fluid models were applied to several paste-like slurry samples to simulate flow and stress states;Casson fluid model was proved to have better simulation effect on paste-like slurry with shear thinning phenomena;rheological parameters of backfilling slurry made by suggested proportion were measured.Initial yield stress,average apparent viscosity and limiting viscosity are 55.35 Pa,1.216 Pa-s and 0.48 Pa-s,respectively.Compared with Bingham fluid model,Casson fluid model has a better simulation effect on paste-like slurry with shear thinning phenomena,through calculating the residual standard deviations.
文摘The concept of the flowing film jigging was first applied to the flowing film concentration area.The flowingfilm jigging function is an important element of the new process,in jection-flowing film centrifugation(IFFC),for separating and recovering minerals of ultrafine sizes.
文摘The Magnetohydrostatic Jigging Separation(MHSJS)is a method which makes use of the vibration of the solid particles obtained by applying a periodically changing magnetic Held to cause a periodically changing magnetic bouyancy to achieve an efficient separation of materials.
基金Project 50474065 supported by the National Natural Science Foundation of China
文摘The laws of motion of particle groups in a jigging process are studied. These describe the macroscopic phenomena that occur during jigging. During jigging the heavier and bigger particles concentrate at the bed bottom while lighter and smaller particles move to the upper part of the bed. Particles with equivalent properties tend to concentrate at a certain position centered around the inherent height of their distribution. The particle distribution variance gradually diminishes to some asymptotic value. The state equation group of the jigging bed is deduced and a calculation method, called the λ value judgment method, is proposed. The method is used to calculate the layer number and the inherent height of each particle group. A mathematical expression for the particle distribution variance is also given.
文摘This paper proposes the expression of the jigging bed porosity based on the jumping height of the jigging bed and water wave. This kind of expression can help to realize the jigging process automation and intelligence. The computer detection system is also developed.
文摘This paper analyzes the detection means of the feeding coal in the jigging process, and puts forward a fuzzy control system of the variable construction in order to control the feeding coal. The fuzzy control system consists of three parts: bang-bang control, keep control and fuzzy control.
基金supported by the National Defense Basic Scientific Research Program of China(Grant numbers JCKY2019427D002).
文摘To address the alignment and measuring force problem in the segmenting-stitching technique for the circularity metrology of small cylindrical workpieces(diameter less than 1.5 mm and length less than 10 mm),a magnet combination jig method is proposed.A small round magnet is attached between the round magnetic jig and small cylinder,and the other end of the small cylindrical workpiece is attached to some cylindrical magnets.Thus,the smaller cylinder can be put in the V-groove and measured successfully with the magnet combination.For verifying the advantage of the magnet combination jig,four measurement quality evaluations are proposed:the circumferential deviation of neighbor arc contours,radial deviation of neighbor arc contours,angle of inclination between the V-groove and small cylinder,and curvature of the obtained arc.The results show that the matching coefficient is enhanced by 98%,the Euclidean distance of overlap parts of neighbor arc contours is reduced by 68%,the position error is reduced 27%,and the average curvature of the arc contours is improved.It can be concluded that the measuring quality can be enhanced prominently by this magnet combination method for the segmenting-stitching method.
文摘Considerable amounts of coal particles are accumulated in the tailing dams of washing plants which can make serious environmental problems. Recovery of these particles from tailings has economically and environmentally several advantages. Maintaining natural resources and reducing discharges to the dams are the most important ones. This study was examined the possibility to recover coal particles from a tailing dam with 56.29% ash content by using series of processing techniques. For this purpose, gravity separation （jig, shaking table and spiral） and flotation tests were conducted to upgrade products. Based the optimum value of these processing methods, a flowsheet was designed to increase the rate of recovery for a wide range of coal particles. Results indicated that the designed circuit can recover over 90% of value coal particles and reduce ash content of product to less than 14%. These results can potentially be used for designing an industrial operation as a recycling plant and an appropriate instance for other areas to reduce the environmental issues of coal tailing dams.
基金Supported by the National High Technology Research and Development Program of China(863 Program)(No.2012AA092303)the Public Science and Technology Research Funds Projects of Ocean(No.20155014)+2 种基金the Shanghai Leading Academic Discipline Projectthe Funding Program for Outstanding Dissertation in Shanghai Ocean UniversitySupported by SHOU International Center for Marine Studies and Shanghai 1000 Talent Program
文摘Catch per unit of eff ort(CPUE) data can display spatial autocorrelation. However, most of the CPUE standardization methods developed so far assumes independency of observations for the dependent variable, which is often invalid. In this study, we collected data of two fisheries, squid jigging fishery and mackerel trawl fishery. We used standard generalized linear model(GLM) and spatial GLMs to compare the impact of spatial autocorrelation on CPUE standardization for different fisheries. We found that spatialGLMs perform better than standard-GLM for both fisheries. The overestimation of precision of CPUE estimates was observed in both fisheries. Moran's I was used to quantify the level of autocorrelation for the two fisheries. The results show that autocorrelation in mackerel trawl fishery was much stronger than that in squid jigging fishery. According to the results of this paper, we highly recommend to account for spatial autocorrelation when using GLM to standardize CPUE data derived from commercial fisheries.
文摘Beneficiation of coal of -4.76 mm + 3 mm size fraction was investigated in a laboratory model Denver jig.Process variables were studied to analyze their effect on the performance of jig in terms of yield and ash content of clean coal. Three-factor three-level Box-Behnken design of experiments with response surface methodology(RSM) was employed to understand the performance behavior of jig. From the study, the bed height was found to be the most significant parameter affecting the yield and ash content of clean coal. It was possible to reduce the ash content from 24.32% in feed to an ash content of 16.55% in clean coal at 2 L/min water flow rate and 10 min jigging time. Influence of operating variables of the jig on responses was presented and discussed in 3D surface plots. The developed model was found to be significant within the range of parameters under investigation with correlation of co-efficient values as 0.99(yield) and 0.98(ash).
文摘Hills Like White Elephants is a short story by Ernest Hemingway.It is a story about an American man and a pregnant girl.As the protagonist,Jig is considered as a submissive woman who has no definite views of her own.This paper attempts to analyze the changes of Jig's inner thought during the forty minutes of waiting the train.In addition to how the girl has grown up from a weak and dependent character into a brave and independent female after the painful struggle in the helpless and hopeless states under the great pressure of the man.
文摘AIM: To compare the postoperative mechanical alignment achieved after total knee arthroplasty(TKA) using computer tomography(CT) based patient specific blocks(PSB) to conventional instruments(CI).METHODS: Total 80 knees were included in the study, with 40 knees in both the groups operated using PSB and CI. All the knees were performed by a single surgeon using the same cruciate sacrificing implants. In our study we used CT based PSB to compare with CI. Postoperative mechanical femoro-tibial angle(MFT angle) was measured on long leg x-rays using picture archiving and communication system(PACS). We compared mechanical alignment achieved using PSB and CI in TKA using statistical analysis.RESULTS: The PSB group(group 1) included 17 females and seven males while in CI group(group 2) there were 15 females and eight males. The mean age of patients in group 1 was 60.5 years and in group 2 it was 60.2 years. The mean postoperative MFT angle measured on long-leg radiographs in group 1 was 178.23°(SD = 2.67°, range: 171.9° to 182.5°) while in group 2, the mean MFT angle was 175.73°(SD = 3.62°, range: 166.0° to 179.8°). There was significant improvement in postoperative mechanical alignment(P value = 0.001), in PSB group compared to CI. Number of outliers were also found to be less in group operated with PSB(7 Knee) compared to those operated with CI(17 Knee).CONCLUSION: PSB improve mechanical alignment after total knee arthroplasty, compared to CI. This may lead to lower rates of revision in the PSB based TKA as compared to the conventional instrumentation.
文摘This paper mainly describes that loose of jig bed affects jig's separation effect, and the corresponding fuzzy rules were built. Using the evaluating index of jig's separation effect--imperfection (I) and total misplaced material (Cz), it evaluates status of loose of jig bed by fuzzy inference system. Experimental simulation and applications in practice prove the method's feasibility.
基金provided by the Project of National Scientific and Technical Supporting Programs Funded of China(No.2012BAB13B03)
文摘The air bag deformation data were obtained by high-speed dynamic videos experiments. Based on gas–liquid flow VOF model, dynamic mesh technique and deformation data, numerical simulations for different structure models were achieved, and the law of water motion and influencing factors were analyzed.The results show that the flow in the length direction of the jig is smooth, and second pulsation appears in the separation time and forms the secondary separation. The installation position of screen and the number of air bags have a great influence on the uniformity of flow and velocity. The screen height cannot be too low to avoid forming the unstable flow. At the same time, the screen height cannot be too high, otherwise water velocity will be too small and was unable to provide enough power. At the height of 1.4m,velocity unevenness is minimum and the best uniform flow can be obtained. Compared with double air bags, there are the following features of single air bag: water flow is not smooth, the time achieving the maximum velocity is too long, maximum velocity is smaller, and overall effect is worse than double air bags.
