Aiming at the problems of large load of rotation drive system,low efficiency of torque transmission and high cost for operation and maintenance of liner steering drilling system for the horizontal well,a new method of...Aiming at the problems of large load of rotation drive system,low efficiency of torque transmission and high cost for operation and maintenance of liner steering drilling system for the horizontal well,a new method of liner differential rotary drilling with double tubular strings in the horizontal well is proposed.The technical principle of this method is revealed,supporting tools such as the differential rotation transducer,composite rotary steering system and the hanger are designed,and technological process is optimized.A tool face control technique of steering drilling assembly is proposed and the calculation model of extension limit of liner differential rotary drilling with double tubular strings in horizontal well is established.These results show that the liner differential rotary drilling with double tubular strings is equipped with measurement while drilling(MWD)and positive displacement motor(PDM),and directional drilling of horizontal well is realized by adjusting rotary speed of drill pipe to control the tool face of PDM.Based on the engineering case of deep coalbed methane horizontal well in the eastern margin of Ordos Basin,the extension limit of horizontal drilling with double tubular strings is calculated.Compared with the conventional liner drilling method,the liner differential rotary drilling with double tubular strings increases the extension limit value of horizontal well significantly.The research findings provide useful reference for the integrated design and control of liner completion and drilling of horizontal wells.展开更多
This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double...This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double-layer charge liners were fabricated by using CVD to deposit tungsten layers on the inner surfaces of pure T2 copper liners.The microstructures of the tungsten layers were analyzed using a scanning electron microscope(SEM).The feasibility analysis was carried out by pulsed X-rays,slug-retrieval test and static penetration tests.The shaped charge jet forming and penetration law of inner tungsten-coated double-layer liner were studied by numerical simulation method.The results showed that the double-layer liners could form well-shaped jets.The errors between the X-ray test results and the numerical results were within 11.07%.A slug-retrieval test was found that the retrieved slug was similar to a numerically simulated slug.Compared with the traditional pure copper shaped charge jet,the penetration depth of the double-layer shaped charge liner increased by 11.4% and>10.8% respectively.In summary,the test results are good,and the numerical simulation is in good agreement with the test,which verified the feasibility of using the CVD method to fabricate double-layer charge liners with a high-density and high-strength refractory metal as the inner liner.展开更多
Shaped charge liner(SCL)has been extensively applied in oil recovery and defense industries.Achieving superior penetration capability through optimizing SCL structures presents a substantial challenge due to intricate...Shaped charge liner(SCL)has been extensively applied in oil recovery and defense industries.Achieving superior penetration capability through optimizing SCL structures presents a substantial challenge due to intricate rate-dependent processes involving detonation-driven liner collapse,high-speed jet stretching,and penetration.This study introduces an innovative optimization strategy for SCL structures that employs jet penetration efficiency as the primary objective function.The strategy combines experimentally validated finite element method with machine learning(FEM-ML).We propose a novel jet penetration efficiency index derived from enhanced cutoff velocity and shape characteristics of the jet via machine learning.This index effectively evaluates the jet penetration performance.Furthermore,a multi-model fusion based on a machine learning optimization method,called XGBOOST-MFO,is put forward to optimize SCL structure over a large input space.The strategy's feasibility is demonstrated through the optimization of copper SCL implemented via the FEM-ML strategy.Finally,this strategy is extended to optimize the structure of the recently emerging CrMnFeCoNi high-entropy alloy conical liners and hemispherical copper liners.Therefore,the strategy can provide helpful guidance for the engineering design of SCL.展开更多
Based on the ablation micro-morphological characteristics, thermo-chemical ablation mechanism, and mechanical stripping mechanism, a dual-region solid rocket motor C/C throat liner ablation model and physical model ar...Based on the ablation micro-morphological characteristics, thermo-chemical ablation mechanism, and mechanical stripping mechanism, a dual-region solid rocket motor C/C throat liner ablation model and physical model are established. The ablation program was written and the experimental data of 70 lb BATES engine platform was used for model validation. The relative errors between the simulation calculation results and the experimental results were −6.83% - 10.20%. The ablation program was applied to study the effects of combustion chamber temperature, pressure, oxidation component concentration, throat particle concentration and particle scouring angle on the nozzle throat liner, which provides a reference for the design of the nozzle throat liner and the estimation of solid rocket motor ablation.展开更多
Dense pre-hydrated geosynthetic clay liners(DPH GCLs)were manufactured as innovative materials accompanied by the advantage of lower hydraulic conductivity(k).The k of DPH GCLs permeated with de-ionized water(DIW)was ...Dense pre-hydrated geosynthetic clay liners(DPH GCLs)were manufactured as innovative materials accompanied by the advantage of lower hydraulic conductivity(k).The k of DPH GCLs permeated with de-ionized water(DIW)was 9.8×10^(−12) m/s.The effect of Cu^(2+)synthetic solution on DPH GCLs was discussed.Furthermore,the effect mechanism was studied on the basis of test technologies.A significant adverse impact on hydraulic performance of DPH GCLs is found when the concentration of Cu^(2+)is greater than 1 g/L.SEM,XRD,XRF,FTIR,and XPS analyses show that the effect of Cu^(2+)on DPH GCLs includes two steps.Firstly,Cu^(2+)interacts with hydrophobic organic matter(HOM),and the adhesion of bentonite is destroyed,and some holes appear.The Cu^(2+)contacts with bentonite directly,and Cu^(2+)interacts with bentonite through ion exchange.Passivated phenomenon occurs on the surface of the bentonite,and swelling ability of bentonite is reduced,which causes permeable DPH GCLs.展开更多
Hydroxyl-terminated polybutadiene/toluene diisocyanate(HTPB/TDI)system is widely used in composite solid propellants.The migrations of plasticizers and water molecules from solid propellants and surrounding environmen...Hydroxyl-terminated polybutadiene/toluene diisocyanate(HTPB/TDI)system is widely used in composite solid propellants.The migrations of plasticizers and water molecules from solid propellants and surrounding environment to the inhibitor have always been the important issues.This study focuses on the preparation,characterization and anti-migration behavior of graphene oxide(GO)/HTPB nanocomposite liner.The GO/HTPB(GH)composite liners affect the migration of small molecules through a tighter cross-linked structure and weakening function of small molecule adsorption.The anti-migration performance of the liner at different temperatures was analyzed,and the influence of the added amount of GO on the anti-migration performance and adhesion performance was also systematically studied.The overall performance of the liner is optimized when the amount of GO filler is 0.3 wt%.After adding 0.3 wt%GO,the concentration of dioctyl sebacate(DOS)migrated into the liner is decreased by 23.28%,and the concentration of water molecules is decreased by 51.89%,indicating that the introduction of GO can significantly improve the anti-migration performance of the liner.In addition,the bond strength is greatly increased from 0.25 MPa to 0.95 MPa,which meets the application requirements of the current propellant system.This research provides an important way for the preparation of structure-function synergistic anti-migration composite liners.展开更多
This study proposed an analytical model for the tunnel supported with a tangentially yielding liner in viscoelastic ground.The efficiency of the developed analytical model was verified by comparing the calculated resu...This study proposed an analytical model for the tunnel supported with a tangentially yielding liner in viscoelastic ground.The efficiency of the developed analytical model was verified by comparing the calculated results with associated numerical simulation results.Using the analytical model,a comprehensive parameter sensitivity analysis was performed to examine the effects of the rate of tunnel face advancement,concrete liner thickness,installation time of liner,and strength and thickness of yielding elements on the tunnel responses.The results highlight the significant benefit of the tangentially yielding liner to relieve overstress in the tunnel liner and improve the stability of the tunnel.The yield efficiency of the tangentially yielding liner depends highly on the yielding strength and deformable capacity of the yielding elements and less on the installation time.展开更多
Spin effect of the small diameter shaped charge results in the centrifugal stress during the jet stretching process. Consequently, the jet scatters, which deceases the jet penetration capability. In the present study,...Spin effect of the small diameter shaped charge results in the centrifugal stress during the jet stretching process. Consequently, the jet scatters, which deceases the jet penetration capability. In the present study, a multi-section method was proposed to design the spin-compensation liner. The spincompensation rate(SCR) of the liner was defined as the specific angular velocity that a fluted liner can offset. Based on the plain stress theory, SPH numerical method was applied to study the converging process of the 2D fluted structure. The spin-compensation mechanism of the fluted structure was illustrated. Then, nine cross sections were chosen along the liner axis equidistantly. On each of the section, a 2D fluted structure was designed to offset a given initial angular velocity. After, the optimized fluted structures were integrated into a 3D fluted liner. Jet appearances of the normal liner and the fluted liners under different initial angular velocities were compared, which verifies the practicality of the multi-sectional method. The multi-section optimization method provides a new efficient method of designing the shaped charge liner for a specific usage.展开更多
With the growing global environmental awareness,the development of renewable and green materials has gained increased worldwide interest to substitute conventional materials and are favorable for sustainable economic ...With the growing global environmental awareness,the development of renewable and green materials has gained increased worldwide interest to substitute conventional materials and are favorable for sustainable economic development.This paper proposed a novel eco-friendly sound absorbing structure(NSAS)liner for noise reduction in elevator shafts.The base layer integrated with the shaft walls is a damping gypsum mortarboard,and a rock wool board and a perforated cement mortarboard are used to compose the NSAS.Based on the acoustic impedance theory of porous materials and perforated panels,the sound absorption theory of the NSAS was proposed;the parameter effects of the rock wool board(flow resistivity,porosity,structure factor)and perforated panel(perforated rates,thickness,density,perforated diameter)on NSAS absorption were discussed theoretically for absorption improvement,and experiments were also conducted.Numerical results showed that the perforation rate,the thickness of the perforated plate,and the porosity,flow resistance,and volume density of the rock wool board played a key issue in the absorption performances of the NSAS.Experiments verified the accuracy of the proposed theoretical model.Wideband sound absorption performance of the NSAS at frequencies between 500–1600 Hz was achieved in both numerical analysis and experiments,and the sound absorption coefficient was improved to 0.72 around 1000 Hz after parameter adjustments.The NSAS proposed in this paper can also be made of other renewable materials with preferable structure strength and still has the potential to broaden the absorption bandwidth.It can provide a reference for controlling the elevator shaft noise.展开更多
A new method for manufacturing explosive charge liner of petroleum perforation bullet, using hot press sintering technique, has been introduced in the paper. The sintering process of making explosive charge liner has...A new method for manufacturing explosive charge liner of petroleum perforation bullet, using hot press sintering technique, has been introduced in the paper. The sintering process of making explosive charge liner has been investigated. The mechanical test and SEM analysis indicate that the property of the liner produced by the process is satisfied.展开更多
The equivalence between multilayered barriers regarding diffusion and adsorption was studied. The bottom boundary of the liner system is defined by assuming concentration continuous and flux continuous conditions of t...The equivalence between multilayered barriers regarding diffusion and adsorption was studied. The bottom boundary of the liner system is defined by assuming concentration continuous and flux continuous conditions of the contaminant between the bottom liner layer and the underlying soil. Five different liner systems were compared in terms of solute breakthrough time. The results of the analysis showed that breakthrough time of the hydrophobic organic compounds for a 2-meter-thick compacted clay liner （CCL） could be 3-4 orders of magnitude is greater than the breakthrough time for a geosynthetic clay liner （GCL） composite liner. The GM/GCL and GM/CCL composite liner systems provide a better diffusion barrier for the hydrophilic organic compounds than that for the hydrophobic compounds due to their different Henry＇s coefficient. The calculated breakthrough times of the organic contaminants for the Chinese standard liner systems were found to be generally greater than those for the GCL alternatives, for the specific conditions examined. If the distribution coefficient increases to 2.8 for the hydrophobic compounds or 1.0 for the hydrophilic compounds, the thickness of the attenuation layer needed to achieve the same breakthrough time as the standard liner systems can be reduced by a factor of about 1.9-2.4. As far as diffusive and adsorption contaminant transport are concerned, GM or GCL is less effective than CCL.展开更多
In the dry-sliding process of the woven self-lubricating liner which is used in the self-lubricating spherical plain bearing, the friction heat plays an important role in the tribological performances of the liner. It...In the dry-sliding process of the woven self-lubricating liner which is used in the self-lubricating spherical plain bearing, the friction heat plays an important role in the tribological performances of the liner. It has important value to study on the relationship between tribological performances of the liner and the friction heat. Unforttmately, up to now, published work on this relationship is quite scarce. Therefore, the effect of friction heat on the tribological performances of the liner was investigated in the present work. The tribological behaviors of the liner were evaluated by using the high temperature end surface wear tester. Scanning electron microscopy （SEM） was utilized to examine the morphologies of worn surfaces of the liner and study the failure modes. Differential scanning calorimetry （DSC） measurement and X-ray diffraction （XRD） analysis were performed to study the behaviors of the wear debris. The temperature rise on the worn surface was calculated according to classical models. SEM observation shows that the dominating wear mechanism for the liner is mainly affected by friction shear force, contact pressure and friction heat. Higher fusion heat for the wear debris than that for the pure polytetrafluroethylene （PTFE） indicates that the PTFE is the main portion of the wear debris, and, the PTFE in the wear debris shows a higher crystallisation degree owing to the effects of friction shear force and the friction heat. Combining the calculated temperature rise results with the wear rate of the liner, it can be concluded that the effects of temperature rise o n the tribological performances of the liner become more obvious when the temperature rise exceeds the glass transition temperature （Tg） of the PTFE. The wear resistance of the liner deteriorates dramatically when the temperature rise approaches to the melting point （Ton） of the PTFE. The tribological performances of the liner can be improved when the temperature rise exceeds Tg but is far lower than Ton- The present study on the relationship between the temperature rise and the tribological performances of the liner may provide the basis for further understanding of the wear mechanisms of the liner as well as the relationship between the formation of the PTFE transfer film and the friction heat during the dry-sliding of the Finer.展开更多
A test method based on the condition simulation and a friction and wear test machine featuring in oscillatory movement were set up for self-lubricating spherical plain bearings (SPB). In the machine the condition para...A test method based on the condition simulation and a friction and wear test machine featuring in oscillatory movement were set up for self-lubricating spherical plain bearings (SPB). In the machine the condition parameters such as load, angle and frequency of oscillation and number of test cycles can be properly controlled. The data relating to the tribological properties of the bearing, in terms of friction coefficient, linear wear amount, temperature near friction surface and applied load, can be monitored and recorded simultaneously during test process by a computerized measuring system of the machine. Efforts were made to improve the measurement technology of the friction coefficient in oscillating motion. In result, a well-designed bearing torque mechanism was developed, which could reveal the relation between the friction coefficient and the displacement of oscillating angle in any defined cycle while the curve of friction coefficient vs number of testing cycles was continuously plotted. The tribological properties and service life of four kinds of the bearings, i.e, the sampleⅠ-Ⅳ with different self-lubricating composite liners, including three kinds of polytetrafluoroethylene (PTFE) fiber weave/epoxy resin composite liners and a PTFE plastic/copper grid composite liner, were evaluated by testing, and the wear mechanisms of the liner materials were analyzed.展开更多
According to relevant new regulations in China,a composite liner system involving geosynthetic materials must be installed at the bottom of an expanded landfill.The deformation and integrity of the composite liner und...According to relevant new regulations in China,a composite liner system involving geosynthetic materials must be installed at the bottom of an expanded landfill.The deformation and integrity of the composite liner under a variety of factors are important issue to be considered in the design of a landfill expansion.In this paper,we investigate the strain distribution in geosynthetic materials within the composite liner system of expanded landfills,including strains in geosynthetic materials resulting from overall settlement and lateral movement of landfills,localized subsidence in landfills,and differential settlement around gas venting wells.The allowable strains of geosynthetic materials are discussed based on the results of tensile tests,and the corresponding design criteria for composite liner systems are proposed.Meanwhile,practical measures allowing strain control in geosynthetic materials used in landfill engineering are proposed.展开更多
Liners in wet ball mill for mineral processing industry must bear abrasive wear and corrosive wear, and consequently, the service life of the liner made from traditional materials, such as Hadfield steel and alloyed s...Liners in wet ball mill for mineral processing industry must bear abrasive wear and corrosive wear, and consequently, the service life of the liner made from traditional materials, such as Hadfield steel and alloyed steels, is typically less than ten months. Bimetal liner, made from high Cr white cast iron and carbon steel, has been successfully developed by using liquid-liquid composite lost foam casting process. The microstructure and interface of the composite were analyzed using optical microscope, SEM, EDX and XRD. Micrographs indicate that the boundary of bimetal combination regions is staggered like dogtooth, two liquid metals are not mixed, and the interface presents excellent metallurgical bonding state. After heat treatment, the composite liner specimens have shown excellent properties, including hardness 〉 61 HRC, fracture toughness ak 〉16.5 J.cm2 and bending strength 〉1,600 MPa. Wear comparison was made between the bimetal composite liner and alloyed steel liner in an industrial hematite ball mill of WISCO, and the results of eight-month test in wet grinding environment have proved that the service life of the bimetal composite liner is three times as long as that of the alloyed steel liner.展开更多
The thin aluminum liners with an aspect ratio R/?r 1 have been imploded on the primary test stand(PTS) facility,where R is the outer radius of the liner and ?r is the thickness. The x-ray self-emission images present ...The thin aluminum liners with an aspect ratio R/?r 1 have been imploded on the primary test stand(PTS) facility,where R is the outer radius of the liner and ?r is the thickness. The x-ray self-emission images present azimuthally correlated perturbations in the liner implosions. The experiments show that at-10 ns before the stagnation, the wavelengths of perturbation are about 0.93 mm and 1.67 mm for the small-radius and large-radius liners, respectively. We have utilized the resistive magnetohydrodynamic code PLUTO to study the development of magneto-Rayleigh–Taylor(MRT) instabilities under experimental conditions. The calculated perturbation amplitudes are consistent with the experimental observations very well. We have found that both mode coupling and long implosion distance are responsible for the more developed instabilities in the large-radius liner implosions.展开更多
It is of a vital importance to reduce the frictional losses in marine diesel engines. Advanced surface textures have provided an e ective solution to friction performance of rubbing pairs due to the rapid development ...It is of a vital importance to reduce the frictional losses in marine diesel engines. Advanced surface textures have provided an e ective solution to friction performance of rubbing pairs due to the rapid development of surface engineering techniques. However,the mechanisms through which textured patterns and texturing methods prove beneficial remains unclear. To address this issue,the tribological system of the cylinder liner?piston ring(CLPR) is investigated in this work. Two types of surface textures(Micro concave,Micro V?groove) are processed on the cylinder specimen using di erent processing methods. Comparative study on the friction coe cients,worn surface texture features and oil film characteristics are performed. The results demonstrate that the processing method of surface texture a ect the performance of the CLPR pairs under the specific testing conditions. In addition the micro V?groove processed by CNCPM is more favorable for improving the wear performances at the low load,while the micro?con?cave processed by CE is more favorable for improving the wear performances at the high load. These findings are in helping to understand the e ect of surface texture on wear performance of CLPR.展开更多
This paper studies the shaped charge jet performance in terms of different liner shapes including conical,bell,hemispherical and bi-conical liners.The critical angles and the relevant flow velocities for the zir-coniu...This paper studies the shaped charge jet performance in terms of different liner shapes including conical,bell,hemispherical and bi-conical liners.The critical angles and the relevant flow velocities for the zir-conium liner material were calculated analytically and numerically using Autodyn hydro-code.The relationship between the critical collapse angle and the flow velocity was determined for the conditions of jet formation and coherency.Penetration tests according to the standard testing procedures of APL-RP34(Section-I1)were performed to validate the numerical predictions of the jet performance of the studied liners.It was found that the four shaped charge liners all produced coherent jets with different performances.The penetration depth of the shaped charges with the bell and the bi-conical liner shapesincreased by 10.3%and 22%,respectively,while the crater diameter of shaped charge with hemispherical liner increased by 85%representing the formation of an explosively-formed-projectile(EF),when they are compared with the corresponding jet characteristics of a conical liner shaped charge.nanоci 1cu.展开更多
Steel mesh is used as a passive skin confinement medium to supplement the active support provided by rock bolts for roof and rib control in underground coal mines. Thin spray-on liners(TSL) are believed to have the po...Steel mesh is used as a passive skin confinement medium to supplement the active support provided by rock bolts for roof and rib control in underground coal mines. Thin spray-on liners(TSL) are believed to have the potential to take the place of steel mesh as the skin confinement medium in underground mines.To confirm this belief, large scale laboratory experiments were conducted to compare the behaviour of welded steel mesh and a TSL, when used in conjunction with rock bolts, in reinforcing strata with weak bedding planes and strata prone to guttering, two common rock conditions which exist in coal mines. It was found that while the peak load taken by the simulated rock mass with weak bedding planes acting as the control sample(no skin confinement) was 2494 kN, the corresponding value of the sample with 5 mm thick TSL reinforcement reached 2856 kN. The peak load of the steel mesh reinforced sample was only2321 kN, but this was attributed to the fact that one of the rock bolts broke during the test. The TSL reinforced sample had a similar post-yield behaviour as the steel mesh reinforced one. The results of the large scale guttering test indicated that a TSL is better than steel mesh in restricting rock movement and thus inhibiting the formation of gutters in the roof.展开更多
基金Supported by the Project of National Natural Science Foundation of China(52234002,42230814)。
文摘Aiming at the problems of large load of rotation drive system,low efficiency of torque transmission and high cost for operation and maintenance of liner steering drilling system for the horizontal well,a new method of liner differential rotary drilling with double tubular strings in the horizontal well is proposed.The technical principle of this method is revealed,supporting tools such as the differential rotation transducer,composite rotary steering system and the hanger are designed,and technological process is optimized.A tool face control technique of steering drilling assembly is proposed and the calculation model of extension limit of liner differential rotary drilling with double tubular strings in horizontal well is established.These results show that the liner differential rotary drilling with double tubular strings is equipped with measurement while drilling(MWD)and positive displacement motor(PDM),and directional drilling of horizontal well is realized by adjusting rotary speed of drill pipe to control the tool face of PDM.Based on the engineering case of deep coalbed methane horizontal well in the eastern margin of Ordos Basin,the extension limit of horizontal drilling with double tubular strings is calculated.Compared with the conventional liner drilling method,the liner differential rotary drilling with double tubular strings increases the extension limit value of horizontal well significantly.The research findings provide useful reference for the integrated design and control of liner completion and drilling of horizontal wells.
基金funded by the China Postdoctoral Science Foundation(Grant No.2022M721614)the opening project of State Key Laboratory of Explosion Science and Technology,Beijing Institute of Technology(Grant No.KFJJ23-07M)。
文摘This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double-layer charge liners were fabricated by using CVD to deposit tungsten layers on the inner surfaces of pure T2 copper liners.The microstructures of the tungsten layers were analyzed using a scanning electron microscope(SEM).The feasibility analysis was carried out by pulsed X-rays,slug-retrieval test and static penetration tests.The shaped charge jet forming and penetration law of inner tungsten-coated double-layer liner were studied by numerical simulation method.The results showed that the double-layer liners could form well-shaped jets.The errors between the X-ray test results and the numerical results were within 11.07%.A slug-retrieval test was found that the retrieved slug was similar to a numerically simulated slug.Compared with the traditional pure copper shaped charge jet,the penetration depth of the double-layer shaped charge liner increased by 11.4% and>10.8% respectively.In summary,the test results are good,and the numerical simulation is in good agreement with the test,which verified the feasibility of using the CVD method to fabricate double-layer charge liners with a high-density and high-strength refractory metal as the inner liner.
基金supported by the NSFC Basic Science Center Program for"Multi-scale Problems in Nonlinear Mechanics" (Grant No.11988102)the NSFC (Grant Nos.U2141204,12172367)+2 种基金the Key Research Program of the Chinese Academy of Sciences (Grant No.ZDRW-CN-2021-2-3)the National Key Research and Development Program of China (Grant No.2022YFC3320504-02)the opening project of State Key Laboratory of Explosion Science and Technology (Grant No.KFJJ21-01 and No.KFJJ18-14 M)。
文摘Shaped charge liner(SCL)has been extensively applied in oil recovery and defense industries.Achieving superior penetration capability through optimizing SCL structures presents a substantial challenge due to intricate rate-dependent processes involving detonation-driven liner collapse,high-speed jet stretching,and penetration.This study introduces an innovative optimization strategy for SCL structures that employs jet penetration efficiency as the primary objective function.The strategy combines experimentally validated finite element method with machine learning(FEM-ML).We propose a novel jet penetration efficiency index derived from enhanced cutoff velocity and shape characteristics of the jet via machine learning.This index effectively evaluates the jet penetration performance.Furthermore,a multi-model fusion based on a machine learning optimization method,called XGBOOST-MFO,is put forward to optimize SCL structure over a large input space.The strategy's feasibility is demonstrated through the optimization of copper SCL implemented via the FEM-ML strategy.Finally,this strategy is extended to optimize the structure of the recently emerging CrMnFeCoNi high-entropy alloy conical liners and hemispherical copper liners.Therefore,the strategy can provide helpful guidance for the engineering design of SCL.
文摘Based on the ablation micro-morphological characteristics, thermo-chemical ablation mechanism, and mechanical stripping mechanism, a dual-region solid rocket motor C/C throat liner ablation model and physical model are established. The ablation program was written and the experimental data of 70 lb BATES engine platform was used for model validation. The relative errors between the simulation calculation results and the experimental results were −6.83% - 10.20%. The ablation program was applied to study the effects of combustion chamber temperature, pressure, oxidation component concentration, throat particle concentration and particle scouring angle on the nozzle throat liner, which provides a reference for the design of the nozzle throat liner and the estimation of solid rocket motor ablation.
基金National Key Research and Development Project of China(No.2017FB0310902)。
文摘Dense pre-hydrated geosynthetic clay liners(DPH GCLs)were manufactured as innovative materials accompanied by the advantage of lower hydraulic conductivity(k).The k of DPH GCLs permeated with de-ionized water(DIW)was 9.8×10^(−12) m/s.The effect of Cu^(2+)synthetic solution on DPH GCLs was discussed.Furthermore,the effect mechanism was studied on the basis of test technologies.A significant adverse impact on hydraulic performance of DPH GCLs is found when the concentration of Cu^(2+)is greater than 1 g/L.SEM,XRD,XRF,FTIR,and XPS analyses show that the effect of Cu^(2+)on DPH GCLs includes two steps.Firstly,Cu^(2+)interacts with hydrophobic organic matter(HOM),and the adhesion of bentonite is destroyed,and some holes appear.The Cu^(2+)contacts with bentonite directly,and Cu^(2+)interacts with bentonite through ion exchange.Passivated phenomenon occurs on the surface of the bentonite,and swelling ability of bentonite is reduced,which causes permeable DPH GCLs.
基金the financial support of the National Natural Science Foundation of China(grant number 22005145)the Natural Science Foundation of Jiangsu Province(grant number BK20180495,BK20180698)+1 种基金the Opening Project of Key Laboratory of Special Energy Materials(Nanjing University of Science and Technology)the Fundamental Research Funds for the Priority Academic Program Development of Jiangsu Higher Education Institutions(grant number 30919011404)。
文摘Hydroxyl-terminated polybutadiene/toluene diisocyanate(HTPB/TDI)system is widely used in composite solid propellants.The migrations of plasticizers and water molecules from solid propellants and surrounding environment to the inhibitor have always been the important issues.This study focuses on the preparation,characterization and anti-migration behavior of graphene oxide(GO)/HTPB nanocomposite liner.The GO/HTPB(GH)composite liners affect the migration of small molecules through a tighter cross-linked structure and weakening function of small molecule adsorption.The anti-migration performance of the liner at different temperatures was analyzed,and the influence of the added amount of GO on the anti-migration performance and adhesion performance was also systematically studied.The overall performance of the liner is optimized when the amount of GO filler is 0.3 wt%.After adding 0.3 wt%GO,the concentration of dioctyl sebacate(DOS)migrated into the liner is decreased by 23.28%,and the concentration of water molecules is decreased by 51.89%,indicating that the introduction of GO can significantly improve the anti-migration performance of the liner.In addition,the bond strength is greatly increased from 0.25 MPa to 0.95 MPa,which meets the application requirements of the current propellant system.This research provides an important way for the preparation of structure-function synergistic anti-migration composite liners.
基金We acknowledge the funding support from the University Transportation Center for Underground Transportation Infrastructure(UTC-UTI)at the Colorado School of Mines and the U.S.Department of Transportation(DOT)(Grant No.69A3551747118).
文摘This study proposed an analytical model for the tunnel supported with a tangentially yielding liner in viscoelastic ground.The efficiency of the developed analytical model was verified by comparing the calculated results with associated numerical simulation results.Using the analytical model,a comprehensive parameter sensitivity analysis was performed to examine the effects of the rate of tunnel face advancement,concrete liner thickness,installation time of liner,and strength and thickness of yielding elements on the tunnel responses.The results highlight the significant benefit of the tangentially yielding liner to relieve overstress in the tunnel liner and improve the stability of the tunnel.The yield efficiency of the tangentially yielding liner depends highly on the yielding strength and deformable capacity of the yielding elements and less on the installation time.
基金supported by the project of National Natural Science Foundation of China (NSFC, Grant No. 12032006)。
文摘Spin effect of the small diameter shaped charge results in the centrifugal stress during the jet stretching process. Consequently, the jet scatters, which deceases the jet penetration capability. In the present study, a multi-section method was proposed to design the spin-compensation liner. The spincompensation rate(SCR) of the liner was defined as the specific angular velocity that a fluted liner can offset. Based on the plain stress theory, SPH numerical method was applied to study the converging process of the 2D fluted structure. The spin-compensation mechanism of the fluted structure was illustrated. Then, nine cross sections were chosen along the liner axis equidistantly. On each of the section, a 2D fluted structure was designed to offset a given initial angular velocity. After, the optimized fluted structures were integrated into a 3D fluted liner. Jet appearances of the normal liner and the fluted liners under different initial angular velocities were compared, which verifies the practicality of the multi-sectional method. The multi-section optimization method provides a new efficient method of designing the shaped charge liner for a specific usage.
基金supported by Opening Foundation of Key Laboratory of New Technology for Construction of Cities in Mountain Area,Ministry of Education,China(LNTCCMA-20210104)This work was also supported by the Natural Science Foundation of China(Grant No.51408113)the Natural Science Foundation of Jiangsu Province,China(Grant No.BK20140632).
文摘With the growing global environmental awareness,the development of renewable and green materials has gained increased worldwide interest to substitute conventional materials and are favorable for sustainable economic development.This paper proposed a novel eco-friendly sound absorbing structure(NSAS)liner for noise reduction in elevator shafts.The base layer integrated with the shaft walls is a damping gypsum mortarboard,and a rock wool board and a perforated cement mortarboard are used to compose the NSAS.Based on the acoustic impedance theory of porous materials and perforated panels,the sound absorption theory of the NSAS was proposed;the parameter effects of the rock wool board(flow resistivity,porosity,structure factor)and perforated panel(perforated rates,thickness,density,perforated diameter)on NSAS absorption were discussed theoretically for absorption improvement,and experiments were also conducted.Numerical results showed that the perforation rate,the thickness of the perforated plate,and the porosity,flow resistance,and volume density of the rock wool board played a key issue in the absorption performances of the NSAS.Experiments verified the accuracy of the proposed theoretical model.Wideband sound absorption performance of the NSAS at frequencies between 500–1600 Hz was achieved in both numerical analysis and experiments,and the sound absorption coefficient was improved to 0.72 around 1000 Hz after parameter adjustments.The NSAS proposed in this paper can also be made of other renewable materials with preferable structure strength and still has the potential to broaden the absorption bandwidth.It can provide a reference for controlling the elevator shaft noise.
文摘A new method for manufacturing explosive charge liner of petroleum perforation bullet, using hot press sintering technique, has been introduced in the paper. The sintering process of making explosive charge liner has been investigated. The mechanical test and SEM analysis indicate that the property of the liner produced by the process is satisfied.
基金supported by the National Science Fundfor Distinguished Young Scholars (No. 50425825)the National Natural Science Foundation of China (No.50538080)
文摘The equivalence between multilayered barriers regarding diffusion and adsorption was studied. The bottom boundary of the liner system is defined by assuming concentration continuous and flux continuous conditions of the contaminant between the bottom liner layer and the underlying soil. Five different liner systems were compared in terms of solute breakthrough time. The results of the analysis showed that breakthrough time of the hydrophobic organic compounds for a 2-meter-thick compacted clay liner （CCL） could be 3-4 orders of magnitude is greater than the breakthrough time for a geosynthetic clay liner （GCL） composite liner. The GM/GCL and GM/CCL composite liner systems provide a better diffusion barrier for the hydrophilic organic compounds than that for the hydrophobic compounds due to their different Henry＇s coefficient. The calculated breakthrough times of the organic contaminants for the Chinese standard liner systems were found to be generally greater than those for the GCL alternatives, for the specific conditions examined. If the distribution coefficient increases to 2.8 for the hydrophobic compounds or 1.0 for the hydrophilic compounds, the thickness of the attenuation layer needed to achieve the same breakthrough time as the standard liner systems can be reduced by a factor of about 1.9-2.4. As far as diffusive and adsorption contaminant transport are concerned, GM or GCL is less effective than CCL.
文摘In the dry-sliding process of the woven self-lubricating liner which is used in the self-lubricating spherical plain bearing, the friction heat plays an important role in the tribological performances of the liner. It has important value to study on the relationship between tribological performances of the liner and the friction heat. Unforttmately, up to now, published work on this relationship is quite scarce. Therefore, the effect of friction heat on the tribological performances of the liner was investigated in the present work. The tribological behaviors of the liner were evaluated by using the high temperature end surface wear tester. Scanning electron microscopy （SEM） was utilized to examine the morphologies of worn surfaces of the liner and study the failure modes. Differential scanning calorimetry （DSC） measurement and X-ray diffraction （XRD） analysis were performed to study the behaviors of the wear debris. The temperature rise on the worn surface was calculated according to classical models. SEM observation shows that the dominating wear mechanism for the liner is mainly affected by friction shear force, contact pressure and friction heat. Higher fusion heat for the wear debris than that for the pure polytetrafluroethylene （PTFE） indicates that the PTFE is the main portion of the wear debris, and, the PTFE in the wear debris shows a higher crystallisation degree owing to the effects of friction shear force and the friction heat. Combining the calculated temperature rise results with the wear rate of the liner, it can be concluded that the effects of temperature rise o n the tribological performances of the liner become more obvious when the temperature rise exceeds the glass transition temperature （Tg） of the PTFE. The wear resistance of the liner deteriorates dramatically when the temperature rise approaches to the melting point （Ton） of the PTFE. The tribological performances of the liner can be improved when the temperature rise exceeds Tg but is far lower than Ton- The present study on the relationship between the temperature rise and the tribological performances of the liner may provide the basis for further understanding of the wear mechanisms of the liner as well as the relationship between the formation of the PTFE transfer film and the friction heat during the dry-sliding of the Finer.
文摘A test method based on the condition simulation and a friction and wear test machine featuring in oscillatory movement were set up for self-lubricating spherical plain bearings (SPB). In the machine the condition parameters such as load, angle and frequency of oscillation and number of test cycles can be properly controlled. The data relating to the tribological properties of the bearing, in terms of friction coefficient, linear wear amount, temperature near friction surface and applied load, can be monitored and recorded simultaneously during test process by a computerized measuring system of the machine. Efforts were made to improve the measurement technology of the friction coefficient in oscillating motion. In result, a well-designed bearing torque mechanism was developed, which could reveal the relation between the friction coefficient and the displacement of oscillating angle in any defined cycle while the curve of friction coefficient vs number of testing cycles was continuously plotted. The tribological properties and service life of four kinds of the bearings, i.e, the sampleⅠ-Ⅳ with different self-lubricating composite liners, including three kinds of polytetrafluoroethylene (PTFE) fiber weave/epoxy resin composite liners and a PTFE plastic/copper grid composite liner, were evaluated by testing, and the wear mechanisms of the liner materials were analyzed.
基金Supported by the National Natural Science Foundation of China (50538080)
文摘According to relevant new regulations in China,a composite liner system involving geosynthetic materials must be installed at the bottom of an expanded landfill.The deformation and integrity of the composite liner under a variety of factors are important issue to be considered in the design of a landfill expansion.In this paper,we investigate the strain distribution in geosynthetic materials within the composite liner system of expanded landfills,including strains in geosynthetic materials resulting from overall settlement and lateral movement of landfills,localized subsidence in landfills,and differential settlement around gas venting wells.The allowable strains of geosynthetic materials are discussed based on the results of tensile tests,and the corresponding design criteria for composite liner systems are proposed.Meanwhile,practical measures allowing strain control in geosynthetic materials used in landfill engineering are proposed.
基金supported by the National Natural Science Foundation of China under grant No.50805109the Fundamental Research Funds for the Central Universities under grant No.2011-1a-023
文摘Liners in wet ball mill for mineral processing industry must bear abrasive wear and corrosive wear, and consequently, the service life of the liner made from traditional materials, such as Hadfield steel and alloyed steels, is typically less than ten months. Bimetal liner, made from high Cr white cast iron and carbon steel, has been successfully developed by using liquid-liquid composite lost foam casting process. The microstructure and interface of the composite were analyzed using optical microscope, SEM, EDX and XRD. Micrographs indicate that the boundary of bimetal combination regions is staggered like dogtooth, two liquid metals are not mixed, and the interface presents excellent metallurgical bonding state. After heat treatment, the composite liner specimens have shown excellent properties, including hardness 〉 61 HRC, fracture toughness ak 〉16.5 J.cm2 and bending strength 〉1,600 MPa. Wear comparison was made between the bimetal composite liner and alloyed steel liner in an industrial hematite ball mill of WISCO, and the results of eight-month test in wet grinding environment have proved that the service life of the bimetal composite liner is three times as long as that of the alloyed steel liner.
基金supported by the National Natural Science Foundation of China(Grant Nos.11605013,11775032,11805019,and 11705013)
文摘The thin aluminum liners with an aspect ratio R/?r 1 have been imploded on the primary test stand(PTS) facility,where R is the outer radius of the liner and ?r is the thickness. The x-ray self-emission images present azimuthally correlated perturbations in the liner implosions. The experiments show that at-10 ns before the stagnation, the wavelengths of perturbation are about 0.93 mm and 1.67 mm for the small-radius and large-radius liners, respectively. We have utilized the resistive magnetohydrodynamic code PLUTO to study the development of magneto-Rayleigh–Taylor(MRT) instabilities under experimental conditions. The calculated perturbation amplitudes are consistent with the experimental observations very well. We have found that both mode coupling and long implosion distance are responsible for the more developed instabilities in the large-radius liner implosions.
基金Supported by National Natural Science Foundation of China(Grant No.51422507)Hubei Provincial Natural Science Foundation of China(Grant No.2015CFB372)+1 种基金Fundamental Research Funds for the Central Universities of China(Grant No.2015IVA010)Tribology Science Fund of State Key Laboratory of Tribology of China(Grant No.SKLTKF14B03)
文摘It is of a vital importance to reduce the frictional losses in marine diesel engines. Advanced surface textures have provided an e ective solution to friction performance of rubbing pairs due to the rapid development of surface engineering techniques. However,the mechanisms through which textured patterns and texturing methods prove beneficial remains unclear. To address this issue,the tribological system of the cylinder liner?piston ring(CLPR) is investigated in this work. Two types of surface textures(Micro concave,Micro V?groove) are processed on the cylinder specimen using di erent processing methods. Comparative study on the friction coe cients,worn surface texture features and oil film characteristics are performed. The results demonstrate that the processing method of surface texture a ect the performance of the CLPR pairs under the specific testing conditions. In addition the micro V?groove processed by CNCPM is more favorable for improving the wear performances at the low load,while the micro?con?cave processed by CE is more favorable for improving the wear performances at the high load. These findings are in helping to understand the e ect of surface texture on wear performance of CLPR.
文摘This paper studies the shaped charge jet performance in terms of different liner shapes including conical,bell,hemispherical and bi-conical liners.The critical angles and the relevant flow velocities for the zir-conium liner material were calculated analytically and numerically using Autodyn hydro-code.The relationship between the critical collapse angle and the flow velocity was determined for the conditions of jet formation and coherency.Penetration tests according to the standard testing procedures of APL-RP34(Section-I1)were performed to validate the numerical predictions of the jet performance of the studied liners.It was found that the four shaped charge liners all produced coherent jets with different performances.The penetration depth of the shaped charges with the bell and the bi-conical liner shapesincreased by 10.3%and 22%,respectively,while the crater diameter of shaped charge with hemispherical liner increased by 85%representing the formation of an explosively-formed-projectile(EF),when they are compared with the corresponding jet characteristics of a conical liner shaped charge.nanоci 1cu.
文摘Steel mesh is used as a passive skin confinement medium to supplement the active support provided by rock bolts for roof and rib control in underground coal mines. Thin spray-on liners(TSL) are believed to have the potential to take the place of steel mesh as the skin confinement medium in underground mines.To confirm this belief, large scale laboratory experiments were conducted to compare the behaviour of welded steel mesh and a TSL, when used in conjunction with rock bolts, in reinforcing strata with weak bedding planes and strata prone to guttering, two common rock conditions which exist in coal mines. It was found that while the peak load taken by the simulated rock mass with weak bedding planes acting as the control sample(no skin confinement) was 2494 kN, the corresponding value of the sample with 5 mm thick TSL reinforcement reached 2856 kN. The peak load of the steel mesh reinforced sample was only2321 kN, but this was attributed to the fact that one of the rock bolts broke during the test. The TSL reinforced sample had a similar post-yield behaviour as the steel mesh reinforced one. The results of the large scale guttering test indicated that a TSL is better than steel mesh in restricting rock movement and thus inhibiting the formation of gutters in the roof.
