Waste selective catalytic reduction(SCR)catalyst as a hazardous waste has a significant impact on the environment and human health.In present study,a novel technology for thermal treatment of waste SCR catalyst was pr...Waste selective catalytic reduction(SCR)catalyst as a hazardous waste has a significant impact on the environment and human health.In present study,a novel technology for thermal treatment of waste SCR catalyst was proposed by adding it to sinter mix for iron ore sintering.The influences of coke rate on the flame front propagation,sinter microstructure,and sinter quality during sintering co-processing the waste SCR catalyst process were studied.In situ tests results indicated the maximum sintering bed temperature increased at higher coke rate,indicating more liquid phase generated and higher airflow resistance.The sintering time was longer and the calculated flame front speed dropped at higher coke rate.Sinter microstructure results found the coalescence and reshaping of bubbles were more fully with increasing coke rate.The porosity dropped from 35.28%to 25.66%,the pore average diameter of large pores decreased from 383.76μm to 311.43μm.With increasing coke rate,the sinter indexes of tumbler index,productivity,and yield,increased from 33.2%,9.2 t·m^(-2)·d^(-1),28.9%to 58.0%,36.0 t·m^(-2)·d^(-1),68.9%,respectively.Finally,a comprehensive index was introduced to systematically assess the influence of coke rate on sinter quality,which rose from 100 to 200 when coke rate was increased from 3.5%(mass)to 5.5%(mass).展开更多
The energy consumption of iron ore sintering process is about 10%- 15%of the total of iron and steel industry.Therefore,it is of great significance to take effective measures to reduce the energy consumption in the ir...The energy consumption of iron ore sintering process is about 10%- 15%of the total of iron and steel industry.Therefore,it is of great significance to take effective measures to reduce the energy consumption in the iron ore sintering process to reduce the costs of sintering product and cut down the emissions of harmful gases,such as CO2 and SO2.In this study,the technology development of saving energy and reducing emission in iron ore sintering process was reviewed and discussed;some new directions and measures of saving energy were presented for the sintering process in the future.展开更多
Benzene is a typical component of volatile organic compounds(VOCs)in the iron ore sintering flue gas.The combustion behavior of benzene directly affects the emission of VOCs in iron ore sintering process.The effects o...Benzene is a typical component of volatile organic compounds(VOCs)in the iron ore sintering flue gas.The combustion behavior of benzene directly affects the emission of VOCs in iron ore sintering process.The effects of temperature,benzene,and oxygen concentrations on the conversion ratio of benzene were investigated by experiments and numerical simulation.The experiments were carried out in a tube reactor at temperatures of 773-1098 K,benzene concentrations of 0.01-0.03 vol.%,and oxygen concentrations of 10-21 vol.%.The numerical simulation was performed with the plug flow model in the CHEMKIN program based on a kinetic model that consists of 132 chemical species and 772 elementary step-like reactions.The experimental results reveal that increasing the temperature and benzene concentration could signifi-cantly promote benzene combustion.It is attributed to the increase in the reaction rates of all steps in the pathway for forming CO_(2)and H_(2)O.In addition,due to the large equivalent ratio of oxygen to benzene,the conversion ratio of benzene remained constant at different oxygen concentrations.The simulation results were in good agreement with the experimental results and indicated that six elementary reactions dominated the formations of CO_(2)and H_(2)O.The oxidations of C_(6)H_(5)O,CO,and C_(5)H_(4)O intermediates to CO_(2)were the limiting steps in the reaction pathways.展开更多
To better understand the evolution characteristics of bed porous structure during iron ore sintering,X-ray computed tomography scanning technology was used to analyze the pore parameters in different areas of the sint...To better understand the evolution characteristics of bed porous structure during iron ore sintering,X-ray computed tomography scanning technology was used to analyze the pore parameters in different areas of the sintering bed.A pore skeleton structure model was established to study the characteristics of the airflow channels in different zones.The absolute permeability of different areas was calculated through simulation,and the corresponding streamline and pressure drop distribution were analyzed.The results show that the porosity of raw material zone,high-temperature zone,and sintered zone increases gradually,which are 37.69%,46.41%,and 55.57%,respectively.The absolute permeability calculation results of the raw material zone and sintered zones are 792.49μm^(2) and 20560.80μm^(2),while the tortuosity is 1.77 and 1.45,respectively.Compared with the raw material zone,the flow streamline in the sintered zone is thicker and denser,the airflow resistance and the pressure drop are minor.展开更多
As the emission control regulations get stricter,the NO_x reduction in the sintering process becomes an important environmental concern owing to its role in the formation of photochemical smog and acid rain.The NOxemi...As the emission control regulations get stricter,the NO_x reduction in the sintering process becomes an important environmental concern owing to its role in the formation of photochemical smog and acid rain.The NOxemissions from the sintering machine account for 48% of total amount from the iron and steel industry.Thus,it is essential to reduce NO_x emissions from the sintering machine,for the achievement of clean production of sinter.Ca-Fe oxides,serving as the main binding phase in the sinter,are therefore used as additives into the sintering mixture to reduce NOxemissions.The results show that the NO_x reduction ratio achieves 27.76% with 8% Ca-Fe oxides additives since the Ca-Fe oxides can advance the ignition and inhibit the nitrogen oxidation compared with the conventional condition.Meanwhile,the existence of Ca-Fe oxides was beneficial to the sinter quality since they were typical low melting point compounds.The optimal mass fraction of Ca-Fe oxides additives should be less than 8%since the permeability of sintering bed was significantly decreased with a further increase of the Ca-Fe oxides fines,inhibiting the mineralization reaction of sintering mixture.Additionally,the appropriate particle size can be obtained when mixing an equal amount of Ca-Fe oxides additives of-0.5 mm and 0.5-3.0 mm in size.展开更多
Canadian iron concentrate(CIC)can elevate the ferrous grade and lower the contents of gangue components and harmful elements in the sinter.To understand high-temperature characteristics of CIC and typical iron ore,the...Canadian iron concentrate(CIC)can elevate the ferrous grade and lower the contents of gangue components and harmful elements in the sinter.To understand high-temperature characteristics of CIC and typical iron ore,the formation of the melt was calculated mainly through FactSage 7.2,and melt fluidity(MF)test for iron ore fines and penetration characteristic test of CIC melt into iron ore nuclei were carried out via micro-sintering method.The results show that hematite,calcium ferrites,dicalcium silicate,and magnetite take part in the formation of the melt in N2.The formation temperature of the liquid for CIC is higher than that for hematite/limonite ore.The MF of CIC is lower than that of hematite/limonite ore fines.The MF of hematite/limonite ore fines is dominated by the liquid amount and melt viscosity.The penetration depth(PD)of CIC melt into limonite ore nuclei is smaller than that into hematite ore nuclei.The PD is related to the reaction ability of the nuclei with the melt.Based on above results,sinter pot tests were conducted.The result shows that in the base ore blends including two hematite ores and two limonite ores,adding CIC deteriorates the sintering indexes.Increasing the proportion of high-MF and small-PD hematite ore can significantly improve the sintering indexes.10 mass%is a suit-able proportion for adding CIC in ore blends.展开更多
The strength properties of green sinter beds,including the Young’s modulus and maximum bed strain,were evaluated using uniaxial compression tests.The green-sinter-bed samples were scanned using X-ray computed tomogra...The strength properties of green sinter beds,including the Young’s modulus and maximum bed strain,were evaluated using uniaxial compression tests.The green-sinter-bed samples were scanned using X-ray computed tomography(XCT),and the geometry characteristics of the granules were quantified by XCT image analysis.The orthogonal array method was applied to determine the concomitant effects of the moisture,hydrated lime,and concentrate contents on the bed strength characteristics.Less bed strain was observed when the granules had a thin adhering layer and increased interlock contacts,which had a great capacity to resist the applied load collectively.The optimal combination for decreasing the bed maximum strain was 5.8%moisture,2%hydrated lime,and 0%concentrate.The moisture and concentrate contents were the most significant factors determining the green bed strength.Increasing the moisture and concentrate contents produced granules with a thicker and more deformable adhering layer,resulting in a more compact bed.The addition of hydrated lime inhibited rearrangement,deformation,and fracture of the granules in green sinter bed during compression.展开更多
Poor permeability and low sintering productivity restrict the development of high-bed sintering.An efficient method of the double-layer sintering process(DLSP)was proposed to achieve high-bed sintering and solve the a...Poor permeability and low sintering productivity restrict the development of high-bed sintering.An efficient method of the double-layer sintering process(DLSP)was proposed to achieve high-bed sintering and solve the aforementioned problems.Theoretical calculation and sintering pot experiments were implemented to investigate the double-layer sintering process.Traditional sintering process and DLSP were compared in terms of sintering indices,metallurgical properties and morphology characterization.Under the condition of traditional sintering process,DLSP successfully realized fast velocity and highly productive sintering of 1000-mm high bed.After the sintering bed is charged and ignited twice,the air permeability of the bed has been greatly improved.Sintering time is shortened significantly by simultaneous sintering of the upper and lower feed layers.Under the condition of bed height proportion of 350/650 mm and pre-sintering time of 20 min,the yield,tumbler strength,productivity and solid fuel consumption are 69.96%,65.87%,1.71 t(m^(2)h)^(-1)and 56.71 kg/t,respectively.Magnetite,hematite,calcium ferrite and complex calcium ferrite are the main phases of DLSP products.The metallurgical properties of DSLP products meet the requirement of ironmaking.It indicates that DLSP is an effective method to solve the disadvantages of bad permeability and low sintering productivity in high-bed sintering.展开更多
Resistance in iron ore undergoes a sharp change of up to several orders of magnitude when the sintered solid phase changes to liquid phase.In view of the insufficiency of existing assimilation detection methods,a timi...Resistance in iron ore undergoes a sharp change of up to several orders of magnitude when the sintered solid phase changes to liquid phase.In view of the insufficiency of existing assimilation detection methods,a timing-of-assimilation reaction is proposed,which was judged by continuously detecting the changes in resistance at the reaction interface.Effects of pole position and additional amounts of iron ore on assimilation reaction timing were investigated.The results showed that the suitable depth of pole groove was about 2 mm,and there was no obvious impact when the distance of the poles changed from 4 to 6 mm,or the amount of iron ore changed from 0.4 to 0.6 g.The temperature of sudden change of resistance in the temperature-resistant image was considered to be the lowest assimilation temperature of iron ore.The accuracy of this resistance method was clarified by X-ray diffraction,optical microscope,and scanning electron microscope/energy dispersive spectrometer(SEM/EDS)analyses.展开更多
Reducing NO_(x) emission of iron ore sintering process in a cost effective manner is a challenge for the iron and steel industry at present.Effects of the proportion of mill scale and coke breeze on the NO_(x) emissio...Reducing NO_(x) emission of iron ore sintering process in a cost effective manner is a challenge for the iron and steel industry at present.Effects of the proportion of mill scale and coke breeze on the NO_(x) emission,strength of sinter,and sinter indexes were studied by com-bustion and sinter pot tests.Results showed that the peak value of NO concentration,total of NO emission,and fuel-N conversion rate gradu-ally decreased as the proportions of the mill scale increased because NO was reduced to N_(2) by Fe_(3)O_(4),FeO,and Fe in the mill scale.The strength of sinter reached the highest value at 8.0wt%mill scale due to the formation of minerals with low melting point.The fuel-N conver-sion rate slightly fluctuated and total NO_(x) emission significantly decreased with the decreased proportions of coke breeze because CO forma-tion and content of N element in the sintered mixture decreased.However,the sinter strength also decreased due to the decrease in the amount of the melting minerals.Furthermore,results of the sinter pot tests indicated that NO_(x) emission decreased.The sinter indexes performed well when the proportions of mill scale and coke breeze were 8.0wt%and 3.70wt%respectively in the sintered mixture.展开更多
A new analysis method based on serial sectioning and three-dimensional(3 D)reconstruction was developed to characterize the mineral microstructure of iron ore sinter.Through the 3 Dreconstruction of two types of iron ...A new analysis method based on serial sectioning and three-dimensional(3 D)reconstruction was developed to characterize the mineral microstructure of iron ore sinter.Through the 3 Dreconstruction of two types of iron ore sinters,the morphology and distribution of minerals in three-dimensional space were analyzed,and the volume fraction of minerals in a 3 Dimage was calculated based on their pixel points.In addition,the microhardness of minerals was measured with a Vickers hardness tester.Notably,different mineral compositions and distributions are obtained in these two sinters.The calcium ferrite in Sinter 1 is dendritic with many interconnected pores,and these grains are crisscrossed and interwoven;the calcium ferrite in Sinter 2 is strip shaped and interweaves with magnetite,silicate and columnar pores.The calculated mineral contents based on a two-dimensional region are clearly different among various layers.Quantitative analysis shows that Sinter 1 contains a greater amount of calcium ferrite and hematite,whereas Sinter 2 contains more magnetite and silicate.The microhardness of minerals from highest to lowest is hematite,calcium ferrite,magnetite and silicate.Thus,Sinter 1 has a greater tumbler strength than Sinter 2.展开更多
At present,blast furnace ironmaking is still the main process for producing molten iron,and sinters are the main raw material for blast furnace ironmaking.A sinter with good metallurgical performance can not only ensu...At present,blast furnace ironmaking is still the main process for producing molten iron,and sinters are the main raw material for blast furnace ironmaking.A sinter with good metallurgical performance can not only ensure smooth operation of the blast furnace but also reduce the blast furnace fuel ratio and increase the molten iron production.Structure is the most important factor affecting the metallurgical properties of the sinter.Thus,the research progress of sinter pore and mineral phase structures was reviewed and the mechanism by which they influence sinter properties was expounded.Multiscale characterization methods for the sinter and their advantages and disadvantages were introduced,and the future research direction of sinter was discussed.展开更多
Iron ore sintering process is the main CO_(2) emission source throughout the integrate steelworks,which primarily comes from the combustion of solid fuels.Improving the combustion efficiency and reducing the solid fue...Iron ore sintering process is the main CO_(2) emission source throughout the integrate steelworks,which primarily comes from the combustion of solid fuels.Improving the combustion efficiency and reducing the solid fuel consumption are important ways to reduce the CO_(2) emission in the sintering process.Around the efficient combustion of fuel,the migration behavior and combustion characteristics of solid fuel in the granulation process were investigated.The results indicated that during the granulation process,fuel particles with size less than 0.5 mm mainly migrated into the granules with grain size of 1-3,3-5 and 5-8 mm;fuel particles with size of 0.5^(-1)mm mainly migrated into granules of 1-3 mm;fuel particles with size of 1-3,3-5 and 5-8 mm mainly entered the granules with the same grain size.With the increase in fuel particles grain size from-0.5 to+8 mm,the combustion efficiency exhibited a firstly-increasing and then decreasing tendency,while the NO_(x) exhibited a decreasing tendency.Potential reason can be described that finer fuel particles(-1 mm)easily distributed in the outer layer of the granules,which combusted fiercely due to its larger specific surface area,leading to the development of incomplete combustion and the conversion of fuel nitrogen;the combustion efficiency of larger fuel particles was restricted by the inner diffusion of O_(2),which then contributed to the reduction of NO_(x) under the inadequate combustion atmosphere.展开更多
At present,the continuous accumulation of the flue gas desulfurization(FGD)gypsum in steel plants leads to the serious environmental issues and resource waste.To achieve green and sustainable development for the steel...At present,the continuous accumulation of the flue gas desulfurization(FGD)gypsum in steel plants leads to the serious environmental issues and resource waste.To achieve green and sustainable development for the steel industry,it is significant to improve the usage of by-product gypsum.Employing the sintering FGD gypsum,ferric oxide,and graphite carbon as raw materials,the effects of the carbon content,reaction time,and molar ratio of CaO to Fe_(2)O_(3)on the desulfurization rate of gypsum were studied based on the orthogonal experiment.The results show that the order of the three influencing factors on the desulfurization rate of FGD gypsum is:molar ratio of CaO to Fe_(2)O_(3)>reaction time>carbon content.Under the optimal conditions of 20 wt.%carbon content,4 h reaction time,and 1:1 molar ratio of CaO to Fe_(2)O_(3),the desulfurization rate of desulfurization gypsum is 95.79%,and 97.57 wt.%of calcium ferrite appears in the solid product,which can be used as sintering additive to increase the economic benefits of enterprises and realize the green ecological development mode of internal generation and internal digestion of solid waste in iron and steel enterprises.展开更多
基金supported by the National Natural Science Foundation of China(52036008).
文摘Waste selective catalytic reduction(SCR)catalyst as a hazardous waste has a significant impact on the environment and human health.In present study,a novel technology for thermal treatment of waste SCR catalyst was proposed by adding it to sinter mix for iron ore sintering.The influences of coke rate on the flame front propagation,sinter microstructure,and sinter quality during sintering co-processing the waste SCR catalyst process were studied.In situ tests results indicated the maximum sintering bed temperature increased at higher coke rate,indicating more liquid phase generated and higher airflow resistance.The sintering time was longer and the calculated flame front speed dropped at higher coke rate.Sinter microstructure results found the coalescence and reshaping of bubbles were more fully with increasing coke rate.The porosity dropped from 35.28%to 25.66%,the pore average diameter of large pores decreased from 383.76μm to 311.43μm.With increasing coke rate,the sinter indexes of tumbler index,productivity,and yield,increased from 33.2%,9.2 t·m^(-2)·d^(-1),28.9%to 58.0%,36.0 t·m^(-2)·d^(-1),68.9%,respectively.Finally,a comprehensive index was introduced to systematically assess the influence of coke rate on sinter quality,which rose from 100 to 200 when coke rate was increased from 3.5%(mass)to 5.5%(mass).
文摘The energy consumption of iron ore sintering process is about 10%- 15%of the total of iron and steel industry.Therefore,it is of great significance to take effective measures to reduce the energy consumption in the iron ore sintering process to reduce the costs of sintering product and cut down the emissions of harmful gases,such as CO2 and SO2.In this study,the technology development of saving energy and reducing emission in iron ore sintering process was reviewed and discussed;some new directions and measures of saving energy were presented for the sintering process in the future.
基金This work was supported by the National Natural Science Foundation of China(Nos.51904127 and 51166004)Key R&D Program of Jiangxi Province(Nos.20202BBGL73117 and 20201BBE51013)+2 种基金Nanchang Key Laboratory(No.2021-NCZDSY-020)Pilot Demonstration Project for the Contract Responsibility System of the Provincial Science and Technology Plan Project of Jiangxi Academy of Sciences(Nos.2021YSBG21015,2022YSBG50010 and 2023YSTZX02)Open Project of Jiangxi Zhongke Ecological Civilization Innovation Research Institute(No.JXZK-2020-01).
文摘Benzene is a typical component of volatile organic compounds(VOCs)in the iron ore sintering flue gas.The combustion behavior of benzene directly affects the emission of VOCs in iron ore sintering process.The effects of temperature,benzene,and oxygen concentrations on the conversion ratio of benzene were investigated by experiments and numerical simulation.The experiments were carried out in a tube reactor at temperatures of 773-1098 K,benzene concentrations of 0.01-0.03 vol.%,and oxygen concentrations of 10-21 vol.%.The numerical simulation was performed with the plug flow model in the CHEMKIN program based on a kinetic model that consists of 132 chemical species and 772 elementary step-like reactions.The experimental results reveal that increasing the temperature and benzene concentration could signifi-cantly promote benzene combustion.It is attributed to the increase in the reaction rates of all steps in the pathway for forming CO_(2)and H_(2)O.In addition,due to the large equivalent ratio of oxygen to benzene,the conversion ratio of benzene remained constant at different oxygen concentrations.The simulation results were in good agreement with the experimental results and indicated that six elementary reactions dominated the formations of CO_(2)and H_(2)O.The oxidations of C_(6)H_(5)O,CO,and C_(5)H_(4)O intermediates to CO_(2)were the limiting steps in the reaction pathways.
基金supported by National Natural Science Foundation of China (grant No.52036008).
文摘To better understand the evolution characteristics of bed porous structure during iron ore sintering,X-ray computed tomography scanning technology was used to analyze the pore parameters in different areas of the sintering bed.A pore skeleton structure model was established to study the characteristics of the airflow channels in different zones.The absolute permeability of different areas was calculated through simulation,and the corresponding streamline and pressure drop distribution were analyzed.The results show that the porosity of raw material zone,high-temperature zone,and sintered zone increases gradually,which are 37.69%,46.41%,and 55.57%,respectively.The absolute permeability calculation results of the raw material zone and sintered zones are 792.49μm^(2) and 20560.80μm^(2),while the tortuosity is 1.77 and 1.45,respectively.Compared with the raw material zone,the flow streamline in the sintered zone is thicker and denser,the airflow resistance and the pressure drop are minor.
文摘As the emission control regulations get stricter,the NO_x reduction in the sintering process becomes an important environmental concern owing to its role in the formation of photochemical smog and acid rain.The NOxemissions from the sintering machine account for 48% of total amount from the iron and steel industry.Thus,it is essential to reduce NO_x emissions from the sintering machine,for the achievement of clean production of sinter.Ca-Fe oxides,serving as the main binding phase in the sinter,are therefore used as additives into the sintering mixture to reduce NOxemissions.The results show that the NO_x reduction ratio achieves 27.76% with 8% Ca-Fe oxides additives since the Ca-Fe oxides can advance the ignition and inhibit the nitrogen oxidation compared with the conventional condition.Meanwhile,the existence of Ca-Fe oxides was beneficial to the sinter quality since they were typical low melting point compounds.The optimal mass fraction of Ca-Fe oxides additives should be less than 8%since the permeability of sintering bed was significantly decreased with a further increase of the Ca-Fe oxides fines,inhibiting the mineralization reaction of sintering mixture.Additionally,the appropriate particle size can be obtained when mixing an equal amount of Ca-Fe oxides additives of-0.5 mm and 0.5-3.0 mm in size.
基金The authors are grateful for the financial support of the Fundamental Research Funds for the Central Universities(Grant No.FRF-IC-18-010).
文摘Canadian iron concentrate(CIC)can elevate the ferrous grade and lower the contents of gangue components and harmful elements in the sinter.To understand high-temperature characteristics of CIC and typical iron ore,the formation of the melt was calculated mainly through FactSage 7.2,and melt fluidity(MF)test for iron ore fines and penetration characteristic test of CIC melt into iron ore nuclei were carried out via micro-sintering method.The results show that hematite,calcium ferrites,dicalcium silicate,and magnetite take part in the formation of the melt in N2.The formation temperature of the liquid for CIC is higher than that for hematite/limonite ore.The MF of CIC is lower than that of hematite/limonite ore fines.The MF of hematite/limonite ore fines is dominated by the liquid amount and melt viscosity.The penetration depth(PD)of CIC melt into limonite ore nuclei is smaller than that into hematite ore nuclei.The PD is related to the reaction ability of the nuclei with the melt.Based on above results,sinter pot tests were conducted.The result shows that in the base ore blends including two hematite ores and two limonite ores,adding CIC deteriorates the sintering indexes.Increasing the proportion of high-MF and small-PD hematite ore can significantly improve the sintering indexes.10 mass%is a suit-able proportion for adding CIC in ore blends.
基金This work was financially supported by the China Postdoctoral Science Foundation(grant No.2018M640557)the National Natural Science Foundation of China(grant No.51906212)the National Natural Science Foundation of China(grant No.52036008).
文摘The strength properties of green sinter beds,including the Young’s modulus and maximum bed strain,were evaluated using uniaxial compression tests.The green-sinter-bed samples were scanned using X-ray computed tomography(XCT),and the geometry characteristics of the granules were quantified by XCT image analysis.The orthogonal array method was applied to determine the concomitant effects of the moisture,hydrated lime,and concentrate contents on the bed strength characteristics.Less bed strain was observed when the granules had a thin adhering layer and increased interlock contacts,which had a great capacity to resist the applied load collectively.The optimal combination for decreasing the bed maximum strain was 5.8%moisture,2%hydrated lime,and 0%concentrate.The moisture and concentrate contents were the most significant factors determining the green bed strength.Increasing the moisture and concentrate contents produced granules with a thicker and more deformable adhering layer,resulting in a more compact bed.The addition of hydrated lime inhibited rearrangement,deformation,and fracture of the granules in green sinter bed during compression.
基金the National Key Research and Development Program of China(2017YFB0304301)the Fundamental Research Funds for the Central Universities of Central South University(No.202044016).
文摘Poor permeability and low sintering productivity restrict the development of high-bed sintering.An efficient method of the double-layer sintering process(DLSP)was proposed to achieve high-bed sintering and solve the aforementioned problems.Theoretical calculation and sintering pot experiments were implemented to investigate the double-layer sintering process.Traditional sintering process and DLSP were compared in terms of sintering indices,metallurgical properties and morphology characterization.Under the condition of traditional sintering process,DLSP successfully realized fast velocity and highly productive sintering of 1000-mm high bed.After the sintering bed is charged and ignited twice,the air permeability of the bed has been greatly improved.Sintering time is shortened significantly by simultaneous sintering of the upper and lower feed layers.Under the condition of bed height proportion of 350/650 mm and pre-sintering time of 20 min,the yield,tumbler strength,productivity and solid fuel consumption are 69.96%,65.87%,1.71 t(m^(2)h)^(-1)and 56.71 kg/t,respectively.Magnetite,hematite,calcium ferrite and complex calcium ferrite are the main phases of DLSP products.The metallurgical properties of DSLP products meet the requirement of ironmaking.It indicates that DLSP is an effective method to solve the disadvantages of bad permeability and low sintering productivity in high-bed sintering.
基金financially supported by the China Postdoctoral Science Foundation (No. 2019M662130)the National Natural Science Foundation of China (No. 51674002)
文摘Resistance in iron ore undergoes a sharp change of up to several orders of magnitude when the sintered solid phase changes to liquid phase.In view of the insufficiency of existing assimilation detection methods,a timing-of-assimilation reaction is proposed,which was judged by continuously detecting the changes in resistance at the reaction interface.Effects of pole position and additional amounts of iron ore on assimilation reaction timing were investigated.The results showed that the suitable depth of pole groove was about 2 mm,and there was no obvious impact when the distance of the poles changed from 4 to 6 mm,or the amount of iron ore changed from 0.4 to 0.6 g.The temperature of sudden change of resistance in the temperature-resistant image was considered to be the lowest assimilation temperature of iron ore.The accuracy of this resistance method was clarified by X-ray diffraction,optical microscope,and scanning electron microscope/energy dispersive spectrometer(SEM/EDS)analyses.
基金This work was financially supported by the National Natural Science Foundation of China(No.51904127)the Natural Science Foundation of Jiangxi Province,China(No.20192BAB216018)+1 种基金the research and development Project(No.2018-YYB-05)collaborative innovation Project(No.2018-XTPH1-05)of Jiangxi Academy of Sciences,China.
文摘Reducing NO_(x) emission of iron ore sintering process in a cost effective manner is a challenge for the iron and steel industry at present.Effects of the proportion of mill scale and coke breeze on the NO_(x) emission,strength of sinter,and sinter indexes were studied by com-bustion and sinter pot tests.Results showed that the peak value of NO concentration,total of NO emission,and fuel-N conversion rate gradu-ally decreased as the proportions of the mill scale increased because NO was reduced to N_(2) by Fe_(3)O_(4),FeO,and Fe in the mill scale.The strength of sinter reached the highest value at 8.0wt%mill scale due to the formation of minerals with low melting point.The fuel-N conver-sion rate slightly fluctuated and total NO_(x) emission significantly decreased with the decreased proportions of coke breeze because CO forma-tion and content of N element in the sintered mixture decreased.However,the sinter strength also decreased due to the decrease in the amount of the melting minerals.Furthermore,results of the sinter pot tests indicated that NO_(x) emission decreased.The sinter indexes performed well when the proportions of mill scale and coke breeze were 8.0wt%and 3.70wt%respectively in the sintered mixture.
基金financial support from the National Natural Science Foundation of China(51474164)the China Postdoctoral Science Foundation(2016M602378)
文摘A new analysis method based on serial sectioning and three-dimensional(3 D)reconstruction was developed to characterize the mineral microstructure of iron ore sinter.Through the 3 Dreconstruction of two types of iron ore sinters,the morphology and distribution of minerals in three-dimensional space were analyzed,and the volume fraction of minerals in a 3 Dimage was calculated based on their pixel points.In addition,the microhardness of minerals was measured with a Vickers hardness tester.Notably,different mineral compositions and distributions are obtained in these two sinters.The calcium ferrite in Sinter 1 is dendritic with many interconnected pores,and these grains are crisscrossed and interwoven;the calcium ferrite in Sinter 2 is strip shaped and interweaves with magnetite,silicate and columnar pores.The calculated mineral contents based on a two-dimensional region are clearly different among various layers.Quantitative analysis shows that Sinter 1 contains a greater amount of calcium ferrite and hematite,whereas Sinter 2 contains more magnetite and silicate.The microhardness of minerals from highest to lowest is hematite,calcium ferrite,magnetite and silicate.Thus,Sinter 1 has a greater tumbler strength than Sinter 2.
基金The authors acknowledge the financial support from the National Natural Science Foundation of China(51474164,U1760101 and 51704216).
文摘At present,blast furnace ironmaking is still the main process for producing molten iron,and sinters are the main raw material for blast furnace ironmaking.A sinter with good metallurgical performance can not only ensure smooth operation of the blast furnace but also reduce the blast furnace fuel ratio and increase the molten iron production.Structure is the most important factor affecting the metallurgical properties of the sinter.Thus,the research progress of sinter pore and mineral phase structures was reviewed and the mechanism by which they influence sinter properties was expounded.Multiscale characterization methods for the sinter and their advantages and disadvantages were introduced,and the future research direction of sinter was discussed.
基金supported by the National Natural Science Foundation of China(No.52274344)Provincial Natural Science Foundation of Hunan(No.2022JJ30723)+1 种基金Independent Exploration and Innovation Project of graduate students of Central South University,Hunan Provincial Science and Technology Achievement Transformation and Industrialization Program(No.2020GK4055)China Baowu Low Carbon Metallurgy Innovation Foundation(No.BWLCF202118).
文摘Iron ore sintering process is the main CO_(2) emission source throughout the integrate steelworks,which primarily comes from the combustion of solid fuels.Improving the combustion efficiency and reducing the solid fuel consumption are important ways to reduce the CO_(2) emission in the sintering process.Around the efficient combustion of fuel,the migration behavior and combustion characteristics of solid fuel in the granulation process were investigated.The results indicated that during the granulation process,fuel particles with size less than 0.5 mm mainly migrated into the granules with grain size of 1-3,3-5 and 5-8 mm;fuel particles with size of 0.5^(-1)mm mainly migrated into granules of 1-3 mm;fuel particles with size of 1-3,3-5 and 5-8 mm mainly entered the granules with the same grain size.With the increase in fuel particles grain size from-0.5 to+8 mm,the combustion efficiency exhibited a firstly-increasing and then decreasing tendency,while the NO_(x) exhibited a decreasing tendency.Potential reason can be described that finer fuel particles(-1 mm)easily distributed in the outer layer of the granules,which combusted fiercely due to its larger specific surface area,leading to the development of incomplete combustion and the conversion of fuel nitrogen;the combustion efficiency of larger fuel particles was restricted by the inner diffusion of O_(2),which then contributed to the reduction of NO_(x) under the inadequate combustion atmosphere.
基金Fundamental Research Funds for the Central Universities(FRF-MP-20-018).
文摘At present,the continuous accumulation of the flue gas desulfurization(FGD)gypsum in steel plants leads to the serious environmental issues and resource waste.To achieve green and sustainable development for the steel industry,it is significant to improve the usage of by-product gypsum.Employing the sintering FGD gypsum,ferric oxide,and graphite carbon as raw materials,the effects of the carbon content,reaction time,and molar ratio of CaO to Fe_(2)O_(3)on the desulfurization rate of gypsum were studied based on the orthogonal experiment.The results show that the order of the three influencing factors on the desulfurization rate of FGD gypsum is:molar ratio of CaO to Fe_(2)O_(3)>reaction time>carbon content.Under the optimal conditions of 20 wt.%carbon content,4 h reaction time,and 1:1 molar ratio of CaO to Fe_(2)O_(3),the desulfurization rate of desulfurization gypsum is 95.79%,and 97.57 wt.%of calcium ferrite appears in the solid product,which can be used as sintering additive to increase the economic benefits of enterprises and realize the green ecological development mode of internal generation and internal digestion of solid waste in iron and steel enterprises.
