Heat transfer and temperature evolution in overburden fracture and ground fissures are one of the essential topics for the identification of ground fissures via unmanned aerial vehicle(UAV) infrared imager. In this st...Heat transfer and temperature evolution in overburden fracture and ground fissures are one of the essential topics for the identification of ground fissures via unmanned aerial vehicle(UAV) infrared imager. In this study, discrete element software UDEC was employed to investigate the overburden fracture field under different mining conditions. Multiphysics software COMSOL were employed to investigate heat transfer and temperature evolution of overburden fracture and ground fissures under the influence of mining condition, fissure depth, fissure width, and month alternation. The UAV infrared field measurements also provided a calibration for numerical simulation. The results showed that for ground fissures connected to underground goaf(Fissure Ⅰ), the temperature difference increased with larger mining height and shallow buried depth. In addition, Fissure Ⅰ located in the boundary of the goaf have a greater temperature difference and is easier to be identified than fissures located above the mining goaf. For ground fissures having no connection to underground goaf(Fissure Ⅱ), the heat transfer is affected by the internal resistance of the overlying strata fracture when the depth of Fissure Ⅱ is greater than10 m, the temperature of Fissure Ⅱ gradually equals to the ground temperature as the fissures’ depth increases, and the fissures are difficult to be identified. The identification effect is most obvious for fissures larger than 16 cm under the same depth. In spring and summer, UAV infrared identification of mining fissures should be carried out during nighttime. This study provides the basis for the optimal time and season for the UAV infrared identification of different types of mining ground fissures.展开更多
With the development of global urbanization,the utilization of underground space is more critical and attractive for civil purposes.Various shapes of shield tunnels have been gradually proposed to cope with different ...With the development of global urbanization,the utilization of underground space is more critical and attractive for civil purposes.Various shapes of shield tunnels have been gradually proposed to cope with different geological conditions and service purposes of underground structures.Generally,reducing the burial depth of shield tunnel is conducive to construction and cost saving.However,extremely small overburden depth cannot provide sufficient uplift resistance to maintain the stability and serviceability of the tunnel.To this end,this paper firstly reviewed the status of deriving the minimum sand over-burden depth of circular shield tunnel using mechanical equilibrium(ME)method.It revealed that the estimated depth is rather conservative.Then,the uplift resistance mechanism of both circular and rectangular tunnels was deduced theoretically and verified with the model tests.The theoretical uplift resistance is consistent with the experimental values,indicating the feasibility of the proposed equations.Furthermore,the determination of the minimum soil overburden depth of rectangular shield tunnel under various working conditions was presented through integrated ME method,which can provide more reasonable estimations of suggested tunnel burial depth for practical construction.Additionally,optimizations were made for calculating the uplift resistance,and the soil thickness providing uplift resistance is suggested to be adjusted according to the testing results.The results can provide reference for the design and construction of various shapes of shield tunnels in urban underground space exploitation.展开更多
The demand for alternative low-grade iron ores is on the rise due to the rapid depletion of high-grade natural iron ore resources and the increased need for steel usage in daily life.However,the use of low-grade iron ...The demand for alternative low-grade iron ores is on the rise due to the rapid depletion of high-grade natural iron ore resources and the increased need for steel usage in daily life.However,the use of low-grade iron ores is a constant clinical task for industry metallurgists.Direct smelting of low-grade ores consumes a substantial amount of energy due to the large volume of slag generated.This condition can be avoided by direct reduction followed by magnetic separation(to separate the high amount of gangue or refractory and metal parts)and smelting.Chromite overburden(COB)is a mine waste generated in chromite ore processing,and it mainly consists of iron,chromium,and nickel(<1wt%).In the present work,the isothermal and non-isothermal kinetics of the solid-state reduction of self-reduced pellets prepared using low-grade iron ore(COB)were thoroughly investigated via thermal analysis.The results showed that the reduction of pellets followed a firstorder autocatalytic reaction control mechanism in the temperature range of 900-1100℃.The autocatalytic nature of the reduction reaction was due to the presence of nickel in the COB.The apparent activation energy obtained from the kinetics results showed that the solid-state reactions between COB and carbon were the rate-determining step in iron oxide reduction.展开更多
In order to comprehend the dynamic disaster mechanism induced by overburden rock caving during the advancement of a coal mining face, a physical simulation model is constructed basing on the geological condition of th...In order to comprehend the dynamic disaster mechanism induced by overburden rock caving during the advancement of a coal mining face, a physical simulation model is constructed basing on the geological condition of the 21221 mining face at Qianqiu coal mine in Henan Province, China. This study established, a comprehensive monitoring system to investigate the interrelations and evolutionary characteristics among multiple mechanical parameters, including mining-induced stress, displacement, temperature, and acoustic emission events during overburden rock caving. It is suggested that, despite the uniformity of the overburden rock caving interval, the main characteristic of overburden rock lies in its uneven caving strength. The mining-induced stress exhibits a reasonable interrelation with the displacement, temperature, and acoustic emission events of the rock strata. With the advancement of the coal seam, the mining-induced stress undergoes four successive stages: gentle stability, gradual accumulation, high-level mutation, and a return to stability. The variations in other mechanical parameters does not synchronize with the signifcant changes in mining-induced stress. Before the collapse of overburden rock occurs, rock strata temperature increment decreases and the acoustic emission ringing counts surges with the increase of rock strata displacement and mining-induced stress. Therefore, the collaborative characteristics of mining-induced stress, displacement, temperature, and acoustic emission ringing counts can be identifed as the precursor information or overburden rock caving. These results are in good consistent with on-site situation in the coal mine.展开更多
The Cenozoic-age Makum coal from northeastern India offers numerous research opportunities because of its diverse geochemical and geological characteristics.Due to its high sulfur content,the coal has been found to be...The Cenozoic-age Makum coal from northeastern India offers numerous research opportunities because of its diverse geochemical and geological characteristics.Due to its high sulfur content,the coal has been found to be less useful for industrial purposes.It can,however,serve as a hub for ongoing research on coal-based derivative products.The aim of this research work is to investigate the mineralogical and geochemical compositions of the coal,mine overburden(MOB)and shale samples taken from the Makum coal field and also on establishing a mutual relationship between them.To characterize the geochemical controlling factors of the Makum coal field,the study employs coal petrography,FTIR,mineralogical,and geochemical analysis.According to X-ray diffraction analysis,the major minerals like quartz,kaolinite,haematite,illite,pyrite,and calcite are present in coal and MOB.Pyrite is observed by SEM-EDS analysis as cubic-shaped particles that are smaller than a fewμm in size.The presence of sulfide minerals represents a phase of pyrite mineralization.The petrography study was used to better understand the environment that existed during the formation of the plant material,which aids us in determining the quantity of detrital mineral sediment contained in the coal.According to the ICP-MS analysis,the samples indicate significant levels of rare earth elements including yttrium.The present study reveals higher concentrations of poten-tial hazardous elements in the coal samples,with V,Cr,Ni,Cu,and Zn content in coal being considerably enriched compared to world-average concentrations.The correlation analysis reveals that the potential hazardous elements like Co,Ni,As,and Cu are associated with pyrite as they have strong affinity towards pyrite.Thus,numerous minerals and rare earth elements(REEs)exist,opening up a fresh avenue for more research in the area.This study also assists researchers in understanding the significance of Makum coal and provides numerous ideas for coal characterization.展开更多
This study used the stable and convergent Dufort-Frankel method to differentially discretize the diffusion equation of the ground-well transient electromagnetic secondary field.The absorption boundary condition of com...This study used the stable and convergent Dufort-Frankel method to differentially discretize the diffusion equation of the ground-well transient electromagnetic secondary field.The absorption boundary condition of complex frequency-shifted perfectly matched layer(CFS-PML)was used for truncation so that the low-frequency electromagnetic wave can be better absorbed at the model boundary.A typical three-dimensional(3D)homogeneous half-space model was established and a low-resistivity cube model was analyzed under the half-space condition.The response patterns and drivers of the low-resistivity cube model were discussed under the influence of a low-resistivity overburden.The absorption boundary conditions of CFS-PML significantly affected the low-frequency electromagnetic waves.For a low-resistivity cube around the borehole,its response curve exhibited a single-peak,and the extreme point of the curve corresponded to the center of the low-resistivity body.When the low-resistivity cube was directly below the borehole,the response curve showed three extreme values(two high and one low),with the low corresponding to the center of the low-resistivity body.The total field response of the low-resistivity overburden was stronger than that of the uniform half-space model due to the low-resistivity shielding effect of electromagnetic waves.When the receiving-transmitting distance gradually increased,the effect of the low-resistivity overburden was gradually weakened,and the response of the low-resistivity cube was strengthened.It was affected by the ratio of the overburden resistivity to the resistivity of the low-resistivity body.展开更多
In the Kaiping Coal field,mining of five coal seams,located within 80 m in the Kailuan Group,#5,#7,#8,#9 and#12 coal seam,is difficult due to small interburden thickness,concentrated stress distributions,high coal sea...In the Kaiping Coal field,mining of five coal seams,located within 80 m in the Kailuan Group,#5,#7,#8,#9 and#12 coal seam,is difficult due to small interburden thickness,concentrated stress distributions,high coal seam metamorphism,and complex geological conditions.By using the ZTR12 geological penetration radar(GPR)survey combined with borehole observations,the overburden caving due to mining of the five coals seams was measured.The development characteristics of full-cover rock fractures after mining were obtained from the GPR scan,which provides a measurement basis for the control of rock strata in close multiple coal seam mining.For the first time,it was found that the overburden caving pattern shows a periodic triangular caved characteristic.Furthermore,it is proposed that an upright triangular collapsed pile masonry and an inverted triangular with larger fragments piled up alternately appear in the lower gob.The research results show that the roof structure formed in the gob area can support the key overlying strata,which is beneficial to ensure the integrity and stability of the upper coal seams in multiple-seam mining of close coal seams.展开更多
The cut-off wall in a clay-core rockfill dam built on a thick overburden layer is subjected to a large compressive pressure under the action of the loads such as the dead weight of both the dam and the overburden laye...The cut-off wall in a clay-core rockfill dam built on a thick overburden layer is subjected to a large compressive pressure under the action of the loads such as the dead weight of both the dam and the overburden layer, the frictional force induced by the differential settlement between the cut-off wall and surrounding soils, and the water pressure. Thus, reduction of the stress of the cut-off wall has become one of the main problems for consideration in engineering design. In this paper, numerical analysis of a core rockfill dam built on a thick overburden layer was conducted and some factors influencing the stress-strain behaviors of the cut-off wall were investigated. The factors include the improvement of the overburden layer, the modeling approach for interfacial contact between the cut-off wall and surrounding soils, the modulus of the cut-off wall concrete, and the connected pattern between the cut-off wall and the clay core. The result shows that improving the overburden layer,selecting plastic concrete with a low modulus and high strength, and optimizing the connection between the cut-off wall and the clay core of the dam are effective measures of reducing the deformations and compressive stresses of the cut-off wall. In addition, both the Goodman element and the mud-layer element are suitable for simulating the interfacial contact between the cut-off wall and surrounding soils.展开更多
Surface subsidence is a typical ground movement due to longwall mining, which causes a series of environmental problems and hazards. In China, intensive coal extractions are commonly operated under dense-populated coa...Surface subsidence is a typical ground movement due to longwall mining, which causes a series of environmental problems and hazards. In China, intensive coal extractions are commonly operated under dense-populated coalfields, which exacerbates the negative subsequences resulted from surface settlement. Therefore, effective approaches to control the ground subsidence are in urgent need for the Chinese coal mining industry. This paper presents a newly developed subsidence control technology: isolated overburden grout injection, including the theory, technique and applications. Relevant procedures such as injection system design, grouting material selection, borehole layout, grout take estimation and injection process design are proposed. The applicability of this technology has been demonstrated through physical modelling, field measurements, and case studies. Since 2009, the technology has been successfully applied to 14 longwall areas in 9 Chinese coal mines. The ultimate surface subsidence factors vary from 0.10 to 0.15. This method has a great potential to be popularized and performed where longwall mining are implemented under villages and ground infrastructures.展开更多
To study the impact of modern coal mining on overlying strata and its water bearing conditions,integrated time-lapse geophysical prospecting integrating 3D seismic,electrical and ground penetrating radar method were u...To study the impact of modern coal mining on overlying strata and its water bearing conditions,integrated time-lapse geophysical prospecting integrating 3D seismic,electrical and ground penetrating radar method were used.Through observing and analyzing the geophysical data variations of all stages of pre-mining,mining and post-mining as well as post-mining deposition stable period,impacts of coal mining on stratigraphic structure and its water bearing were studied and modern coal mining induced stratigraphic change pattern was summarized.The research result shows that the stratigraphic structure and the water bearing of surface layer during modern coal mining have self-healing pattern with mining time;the self-healing capability of near-surface strata is relatively strong while the roof weak;water bearing selfhealing of near-surface strata is relatively high while the roof strata adjacent to mined coal beds low.Due to integrated time-lapse geophysical prospecting technology has extra time dimension which makes up the deficiency of static analysis of conventional geophysical methods,it can better highlight the dynamic changes of modern coal mining induced overburden strata and its water bearing conditions.展开更多
The management of overburden is an important task in open pit exploitations. Site topography and morphology as well as geological and geotechnical properties of natural and remoulded materials are the most important f...The management of overburden is an important task in open pit exploitations. Site topography and morphology as well as geological and geotechnical properties of natural and remoulded materials are the most important factors affecting the disposal phase. Economic and environmental requirements must be followed in order to achieve the best reclamation results, keeping into account site constraints such as slope stability, hauling and dumping issues, and interactions with groundwater. This paper deals with the above mentioned issues, illustrating a rational approach applied on the case of a large limestone quarry where the thickness of the overburden is relevant and the spoil material has to be dumped in a flooded pit. The proposed multidisciplinary approach led to the selection of most suitable methods for excavation, transportation and disposal. The selection was based on a detailed laboratory and site characterisation that defined favorable and adverse factors to be considered during the preliminary study of a large quarrying project.展开更多
A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7 ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey(USGS) in 2016.Further investigations by the National In...A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7 ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey(USGS) in 2016.Further investigations by the National Institute for Occupational Safety and Health(NIOSH) and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia.Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity.In order to use the geology as a forecaster of mining-induced seismic events and their energy potential, two primary components are needed.The first component is a long history of recorded seismic events with accurately plotted locations.The second component is a high density of geologic data within the mining area.In this case, 181 events of 1.0 MLor greater were recorded by the mine's seismic network between January, 2009, and October, 2016.Within the mining area, 897 geophysical logs, 224 core holes, and 1031 fiberscope holes were examined by mine geologists.From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations.After the data was analyzed, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions.Three forecast maps were created based on geology of previous seismic locations.The forecast maps have shown an accuracy of within 74%–89% when compared to the recorded 181 events that were1.0 MLor greater when considering three major geological criteria of overburden thickness of 579.12 m or greater, 6.096–12.192 m of sandstone within 15.24 m of the Pocahontas number 3 seam, and a longwall caving height of 4.572 m or less.展开更多
Mining induced pressures are strong and overburden failure areas are large in top coal caving longwall mining, which constrains high production and safety mining. By employing the combination of the full view borehole...Mining induced pressures are strong and overburden failure areas are large in top coal caving longwall mining, which constrains high production and safety mining. By employing the combination of the full view borehole photography technique and the seismic CT scanner technique, the deformation and failure of overlying strata of fully mechanized caving face in shallow coal seam were studied and the failure development of overburden was determined. Results show that the full view borehole photography can reveal the characteristics of strata, and the seismic CT scanner can reflect the characteristics of strata between the boreholes. The combined measurement technique can effectively determine the height of fractured and caved zones. The top end of the caved zone in Yangwangou coal mine employing the top coal caving longwall mining was at the depth of 171 m and fractured zone was at the depth of 106-110 m. The results provide a theoretic foundation for controlling the overburden strata in the shallow buried top coal caving panel.展开更多
The broad objective of this research was to improve current surface mining practices and reduce negative environmental impact of overburden removal in West Virginia(WV).The specific objectives were to(i)compare conven...The broad objective of this research was to improve current surface mining practices and reduce negative environmental impact of overburden removal in West Virginia(WV).The specific objectives were to(i)compare conventional surface mining method(drilling,blasting,digging,and loading)to a surface miner(SM)method,and(ii)apply the analytical hierarchy process(AHP)to help select the optimal mining method based on production,cost and environmental criteria.The design and the procedures used in this research involve five interrelated modules:(i)rock properties of overburden in WV,(ii)drilling and blasting,(iii)digging and loading,(iv)SM method,and(v)comparative analysis and selection of the optimal mining method by AHP.Results of this research indicate that application of SM method would yield higher cost of overburden removal than conventional mining methods in rocks with a high unconfined compressive strength and abrasivity.A significant advantage of SM method,where applicable,is the elimination of the negative environmental impacts associated with blasting.展开更多
The effect of slope angle for external overburden dump in response to average and heavy rainfall has been analyzed using a two dimensional finite difference method of transient water flow through unsaturated–saturate...The effect of slope angle for external overburden dump in response to average and heavy rainfall has been analyzed using a two dimensional finite difference method of transient water flow through unsaturated–saturated soil. The external dump stability is evaluated for five geomaterial types on the basis of globally accepted safety factor analysis technique, based on shear strength reduction approach using finite difference method. The results obtained from the finite difference method of analysis indicate that the external dump with more than 30° slope angle is greatly influenced by the rainfall under the studied conditions for geomaterial 3, 4 and 5, whereas dumps with geomaterial 1 and 2 remain safe. The analysis shows that major slope failure is out of preview for the studied rainfall conditions.展开更多
Rock typing is an important tool in evaluation and performance prediction of reservoirs.Different techniques such as flow zone indicator(FZI),FZI~*and Winland methods are used to categorize reservoir rocks into distin...Rock typing is an important tool in evaluation and performance prediction of reservoirs.Different techniques such as flow zone indicator(FZI),FZI~*and Winland methods are used to categorize reservoir rocks into distinct rock types.Generally,these methods are applied to petrophysical data that are measured at a pressure other than reservoir pressure.Since the pressure changes the pore structure of rock,the effect of overburden pressure on rock typing should be considered.In this study,porosity and permeability of 113 core samples were measured at five different pressures.To investigate the effect of pressure on determination of rock types,FZI,FZI~*and Winland methods were applied.Results indicated that although most of the samples remain in the same rock type when pressure changes,some of them show different trends.These are related to the mineralogy and changes in pore system of the samples due to pressure change.Additionally,the number of rock types increases with increasing pressure.Furthermore,the effect of overburden pressure on determination of rock types is more clearly observed in the Winland and FZI~*methods.Also,results revealed that a more precise reservoir dynamic simulation can be obtained by considering the reservoir rock typing process at reservoir conditions.展开更多
Understanding the spatiotemporal evolution of overburden deformation during coal mining is still a challenge in engineering practice due to the limitation of monitoring techniques. Taking the Yangliu Coal Mine as an e...Understanding the spatiotemporal evolution of overburden deformation during coal mining is still a challenge in engineering practice due to the limitation of monitoring techniques. Taking the Yangliu Coal Mine as an example, a similarity model test was designed and conducted to investigate the deformation and failure mechanism of overlying rocks in this study. Distributed fiber optic sensing(DFOS), highdensity electrical resistivity tomography(HD-ERT) and close-range photogrammetry(CRP) technologies were used in the test for comprehensive analyses. The combined use of the three methods facilitates the investigation of the spatiotemporal evolution characteristics of overburden deformation, showing that the mining-induced deformation of overburden strata was a dynamic evolution process. This process was accompanied by the formation, propagation, closure and redevelopment of separation cracks.Moreover, the key rock stratum with high strength and high-quality lithology played a crucial role in the whole process of overburden deformation. There were generally three failure modes of overburden rock layers, including bending and tension, overall shearing, and shearing and sliding. Shear failure often leads to overburden falling off in blocks, which poses a serious threat to mining safety. Therefore, realtime and accurate monitoring of overburden deformation is of great significance for the safe mining of underground coal seams.展开更多
The backfilling mining technology is a type of high-efficiency coal mining technology that is used to address the environmental issues caused by the caving mining technology.In this paper,the mechanical model of symme...The backfilling mining technology is a type of high-efficiency coal mining technology that is used to address the environmental issues caused by the caving mining technology.In this paper,the mechanical model of symmetrical laminated plate representing the overburden movement caused by the backfilling mining technology is established,and the governing differential equation of the motion of the overburden is derived.The boundary conditions of the mechanical model are put forward,and the analytical solution of the overburden movement and surface subsidence is obtained.The numerical model of the overburden movement and surface subsidence,under mining with backfilling,is established by means of the FLAC3D numerical software,which aims to systematically study the influence of backfilling compactness,mining thickness,and mining depth on the overburden movement and surface subsidence in backfilling mining.When the compactnessηis less than 70%,the overburden movement and surface subsidence is greater,while whenηis greater than 70%,the overburden movement and surface subsidence is reduced significantly.On this basis,the control mechanism of surface subsidence and overburden movement in backfilling mining is obtained.The suitable backfilling compactness is the key to controlling surface subsidence and overburden movement in backfilling mining.展开更多
Reservoir quality from cored intervals has traditionally been described by grouping similar intervals according to rock type. The main shortcoming of this static modelling approach is that it lacks clarity and it is n...Reservoir quality from cored intervals has traditionally been described by grouping similar intervals according to rock type. The main shortcoming of this static modelling approach is that it lacks clarity and it is not conducive for setting up a dynamic simulation model. The alternative is to use a modelling approach based on Hydraulic Flow Zone Units (HFZUs). First proposed in the late 1980s and extensively published in the early 1990s such formulation uses the well-known Carman-Kozeny (C-K) equation. More recently, this approach has been extended to cover a wider range of geological formations with diverse pore structure types. In using a HFZU approach, a pre-processing step is customarily undertaken to first overburden correct the data and where necessary also to correct for the Klinkenberg effect (lower permeability formations, lab testing with gas). The study presented compares corrected and uncorrected data sets, to see if correction alters the overall outcome of HFZU analysis. Specifically, data sets are compared at three different conditions: ambient, overburden (only) corrected and finally data that has been corrected for both, overburden and Klinkenberg effects. In all cases it is the Flow Zone Indicator (FZI), an index representative of formation quality that is tracked, together with the type of relationship. Several comparative analysis examples are given for diverse formations. The results show that uncorrected data can yield a different correlation and FZI, especially for intervals that include low permeability samples. Results indicate that Overburden and Klinkenberg corrections should be applied before HFZU analysis.展开更多
Coal pillar design has historically assigned a factor of safety(Fo S) or stability factor(SF) according to their estimated strength and the assumed overburden load acting on them. Acceptable Fo S values have been assi...Coal pillar design has historically assigned a factor of safety(Fo S) or stability factor(SF) according to their estimated strength and the assumed overburden load acting on them. Acceptable Fo S values have been assigned based on past mining experience or a statistical link between Fo S and probability of failure(Po F). Pillar width-to-height(w/h) ratio has long been established as having a material influence on both pillar strength and its potential failure mode. However, there has been significant disagreement on using both factor of safety(Fo S) and w/h as part of pillar system stability criterion, as compared to using Fo S in isolation. This paper will argue that there are valid technical reasons to bring w/h ratio into system stability criteria(other than its influence on pillar strength), as it is related to the post-failure stiffness of the pillar, as measured in situ, and its interaction with overburden stiffness. When overburden stiffness is also brought into pillar system stability considerations, two issues emerge. The first is the width-todepth(W/D) ratio of the panel and whether it is sub-critical or super-critical from a surface subsidence perspective. The second relates to a re-evaluation of pillar Fo S based on whether the pillar is in an elastic or non-elastic(i.e., post-yield) state in its as-designed condition, as this is relevant to maintaining overburden stiffness at the highest possible level. The significance of the model is the potential to maximise both reserve recovery and mining efficiencies without any discernible increase in geotechnical risk, particularly in thick seams and higher depth of cover mining situations. At a time when mining economics are, at best, marginal, removing potentially unnecessary design conservatism is of interest to all mine operators and is an important topic for discussion amongst the geotechnical community.展开更多
基金supported by the National Natural Science Foundation of China(Nos.52225402 and U1910206).
文摘Heat transfer and temperature evolution in overburden fracture and ground fissures are one of the essential topics for the identification of ground fissures via unmanned aerial vehicle(UAV) infrared imager. In this study, discrete element software UDEC was employed to investigate the overburden fracture field under different mining conditions. Multiphysics software COMSOL were employed to investigate heat transfer and temperature evolution of overburden fracture and ground fissures under the influence of mining condition, fissure depth, fissure width, and month alternation. The UAV infrared field measurements also provided a calibration for numerical simulation. The results showed that for ground fissures connected to underground goaf(Fissure Ⅰ), the temperature difference increased with larger mining height and shallow buried depth. In addition, Fissure Ⅰ located in the boundary of the goaf have a greater temperature difference and is easier to be identified than fissures located above the mining goaf. For ground fissures having no connection to underground goaf(Fissure Ⅱ), the heat transfer is affected by the internal resistance of the overlying strata fracture when the depth of Fissure Ⅱ is greater than10 m, the temperature of Fissure Ⅱ gradually equals to the ground temperature as the fissures’ depth increases, and the fissures are difficult to be identified. The identification effect is most obvious for fissures larger than 16 cm under the same depth. In spring and summer, UAV infrared identification of mining fissures should be carried out during nighttime. This study provides the basis for the optimal time and season for the UAV infrared identification of different types of mining ground fissures.
基金support from National Major Scientific Instruments Development Project of China(Grant No.5202780029)Program of Distinguished Young Scholars,Natural Science Foundation of Chongqing,China(Grant No.cstc2020jcyjjq0087)Research on resilience prevention,control and adaptation strategy of flood disaster in megacities under changing environment(Grant No.2021-ZD-CQ-2).
文摘With the development of global urbanization,the utilization of underground space is more critical and attractive for civil purposes.Various shapes of shield tunnels have been gradually proposed to cope with different geological conditions and service purposes of underground structures.Generally,reducing the burial depth of shield tunnel is conducive to construction and cost saving.However,extremely small overburden depth cannot provide sufficient uplift resistance to maintain the stability and serviceability of the tunnel.To this end,this paper firstly reviewed the status of deriving the minimum sand over-burden depth of circular shield tunnel using mechanical equilibrium(ME)method.It revealed that the estimated depth is rather conservative.Then,the uplift resistance mechanism of both circular and rectangular tunnels was deduced theoretically and verified with the model tests.The theoretical uplift resistance is consistent with the experimental values,indicating the feasibility of the proposed equations.Furthermore,the determination of the minimum soil overburden depth of rectangular shield tunnel under various working conditions was presented through integrated ME method,which can provide more reasonable estimations of suggested tunnel burial depth for practical construction.Additionally,optimizations were made for calculating the uplift resistance,and the soil thickness providing uplift resistance is suggested to be adjusted according to the testing results.The results can provide reference for the design and construction of various shapes of shield tunnels in urban underground space exploitation.
文摘The demand for alternative low-grade iron ores is on the rise due to the rapid depletion of high-grade natural iron ore resources and the increased need for steel usage in daily life.However,the use of low-grade iron ores is a constant clinical task for industry metallurgists.Direct smelting of low-grade ores consumes a substantial amount of energy due to the large volume of slag generated.This condition can be avoided by direct reduction followed by magnetic separation(to separate the high amount of gangue or refractory and metal parts)and smelting.Chromite overburden(COB)is a mine waste generated in chromite ore processing,and it mainly consists of iron,chromium,and nickel(<1wt%).In the present work,the isothermal and non-isothermal kinetics of the solid-state reduction of self-reduced pellets prepared using low-grade iron ore(COB)were thoroughly investigated via thermal analysis.The results showed that the reduction of pellets followed a firstorder autocatalytic reaction control mechanism in the temperature range of 900-1100℃.The autocatalytic nature of the reduction reaction was due to the presence of nickel in the COB.The apparent activation energy obtained from the kinetics results showed that the solid-state reactions between COB and carbon were the rate-determining step in iron oxide reduction.
基金supported by the State Key Research Development Program of China(2022YFC3004602)Independent Research fund of Joint NationalLocal Engineering Research Centre for Safe and Precise Coal Mining(Anhui University of Science and Technology)(EC2022001)+2 种基金the National Natural Science Foundation of China(41872205)Beijing Natural Science Foundation(8202041)the Fundamental Research Funds for the Central Universities(2022YJSLJ08,2022JCCXNY03).
文摘In order to comprehend the dynamic disaster mechanism induced by overburden rock caving during the advancement of a coal mining face, a physical simulation model is constructed basing on the geological condition of the 21221 mining face at Qianqiu coal mine in Henan Province, China. This study established, a comprehensive monitoring system to investigate the interrelations and evolutionary characteristics among multiple mechanical parameters, including mining-induced stress, displacement, temperature, and acoustic emission events during overburden rock caving. It is suggested that, despite the uniformity of the overburden rock caving interval, the main characteristic of overburden rock lies in its uneven caving strength. The mining-induced stress exhibits a reasonable interrelation with the displacement, temperature, and acoustic emission events of the rock strata. With the advancement of the coal seam, the mining-induced stress undergoes four successive stages: gentle stability, gradual accumulation, high-level mutation, and a return to stability. The variations in other mechanical parameters does not synchronize with the signifcant changes in mining-induced stress. Before the collapse of overburden rock occurs, rock strata temperature increment decreases and the acoustic emission ringing counts surges with the increase of rock strata displacement and mining-induced stress. Therefore, the collaborative characteristics of mining-induced stress, displacement, temperature, and acoustic emission ringing counts can be identifed as the precursor information or overburden rock caving. These results are in good consistent with on-site situation in the coal mine.
基金MoES (Govt of India)for his financial assistance to our project (GPP364).
文摘The Cenozoic-age Makum coal from northeastern India offers numerous research opportunities because of its diverse geochemical and geological characteristics.Due to its high sulfur content,the coal has been found to be less useful for industrial purposes.It can,however,serve as a hub for ongoing research on coal-based derivative products.The aim of this research work is to investigate the mineralogical and geochemical compositions of the coal,mine overburden(MOB)and shale samples taken from the Makum coal field and also on establishing a mutual relationship between them.To characterize the geochemical controlling factors of the Makum coal field,the study employs coal petrography,FTIR,mineralogical,and geochemical analysis.According to X-ray diffraction analysis,the major minerals like quartz,kaolinite,haematite,illite,pyrite,and calcite are present in coal and MOB.Pyrite is observed by SEM-EDS analysis as cubic-shaped particles that are smaller than a fewμm in size.The presence of sulfide minerals represents a phase of pyrite mineralization.The petrography study was used to better understand the environment that existed during the formation of the plant material,which aids us in determining the quantity of detrital mineral sediment contained in the coal.According to the ICP-MS analysis,the samples indicate significant levels of rare earth elements including yttrium.The present study reveals higher concentrations of poten-tial hazardous elements in the coal samples,with V,Cr,Ni,Cu,and Zn content in coal being considerably enriched compared to world-average concentrations.The correlation analysis reveals that the potential hazardous elements like Co,Ni,As,and Cu are associated with pyrite as they have strong affinity towards pyrite.Thus,numerous minerals and rare earth elements(REEs)exist,opening up a fresh avenue for more research in the area.This study also assists researchers in understanding the significance of Makum coal and provides numerous ideas for coal characterization.
基金This work was supported by China Postdoctoral Science Foundation(No.2022M723391)the Science and Technology Innovation Project of Higher Education in Shanxi Province(No.2019L0754)+1 种基金the Central Guiding Local Science and Technology Development Fund Project(No.YDZJSX2021B021)Shanxi Province Basic Research Plan General Project(No.202203021221294).
文摘This study used the stable and convergent Dufort-Frankel method to differentially discretize the diffusion equation of the ground-well transient electromagnetic secondary field.The absorption boundary condition of complex frequency-shifted perfectly matched layer(CFS-PML)was used for truncation so that the low-frequency electromagnetic wave can be better absorbed at the model boundary.A typical three-dimensional(3D)homogeneous half-space model was established and a low-resistivity cube model was analyzed under the half-space condition.The response patterns and drivers of the low-resistivity cube model were discussed under the influence of a low-resistivity overburden.The absorption boundary conditions of CFS-PML significantly affected the low-frequency electromagnetic waves.For a low-resistivity cube around the borehole,its response curve exhibited a single-peak,and the extreme point of the curve corresponded to the center of the low-resistivity body.When the low-resistivity cube was directly below the borehole,the response curve showed three extreme values(two high and one low),with the low corresponding to the center of the low-resistivity body.The total field response of the low-resistivity overburden was stronger than that of the uniform half-space model due to the low-resistivity shielding effect of electromagnetic waves.When the receiving-transmitting distance gradually increased,the effect of the low-resistivity overburden was gradually weakened,and the response of the low-resistivity cube was strengthened.It was affected by the ratio of the overburden resistivity to the resistivity of the low-resistivity body.
基金The research is supported by National Key R&D Program of China(No.2017YFC060300204)National Natural Science Foundation of China(No.52074293)+2 种基金Hebei Province Natural Science Foundation of China(No.E2020402041)Yue Qi Young Scholar Project,CUMTB and Yue Qi Distinguished Scholar Project(No.800015Z1138)China University of Mining&Technology,Beijing.
文摘In the Kaiping Coal field,mining of five coal seams,located within 80 m in the Kailuan Group,#5,#7,#8,#9 and#12 coal seam,is difficult due to small interburden thickness,concentrated stress distributions,high coal seam metamorphism,and complex geological conditions.By using the ZTR12 geological penetration radar(GPR)survey combined with borehole observations,the overburden caving due to mining of the five coals seams was measured.The development characteristics of full-cover rock fractures after mining were obtained from the GPR scan,which provides a measurement basis for the control of rock strata in close multiple coal seam mining.For the first time,it was found that the overburden caving pattern shows a periodic triangular caved characteristic.Furthermore,it is proposed that an upright triangular collapsed pile masonry and an inverted triangular with larger fragments piled up alternately appear in the lower gob.The research results show that the roof structure formed in the gob area can support the key overlying strata,which is beneficial to ensure the integrity and stability of the upper coal seams in multiple-seam mining of close coal seams.
基金the National Natural Science Foundation of China (Grant No.51379066)the Fundamental Research Funds for the Central Universities (Grant No.2016B03514)+1 种基金the National Key Technology Support Program (Grant No.2015BAB07B05)the Key Laboratory of Earth-Rock Dam Failure Mechanism and Safety Control Techniques (Grant No.YK913007).
文摘The cut-off wall in a clay-core rockfill dam built on a thick overburden layer is subjected to a large compressive pressure under the action of the loads such as the dead weight of both the dam and the overburden layer, the frictional force induced by the differential settlement between the cut-off wall and surrounding soils, and the water pressure. Thus, reduction of the stress of the cut-off wall has become one of the main problems for consideration in engineering design. In this paper, numerical analysis of a core rockfill dam built on a thick overburden layer was conducted and some factors influencing the stress-strain behaviors of the cut-off wall were investigated. The factors include the improvement of the overburden layer, the modeling approach for interfacial contact between the cut-off wall and surrounding soils, the modulus of the cut-off wall concrete, and the connected pattern between the cut-off wall and the clay core. The result shows that improving the overburden layer,selecting plastic concrete with a low modulus and high strength, and optimizing the connection between the cut-off wall and the clay core of the dam are effective measures of reducing the deformations and compressive stresses of the cut-off wall. In addition, both the Goodman element and the mud-layer element are suitable for simulating the interfacial contact between the cut-off wall and surrounding soils.
基金financial support provided by the National Natural Science Foundation of China(51604258)is greatly appreciated
文摘Surface subsidence is a typical ground movement due to longwall mining, which causes a series of environmental problems and hazards. In China, intensive coal extractions are commonly operated under dense-populated coalfields, which exacerbates the negative subsequences resulted from surface settlement. Therefore, effective approaches to control the ground subsidence are in urgent need for the Chinese coal mining industry. This paper presents a newly developed subsidence control technology: isolated overburden grout injection, including the theory, technique and applications. Relevant procedures such as injection system design, grouting material selection, borehole layout, grout take estimation and injection process design are proposed. The applicability of this technology has been demonstrated through physical modelling, field measurements, and case studies. Since 2009, the technology has been successfully applied to 14 longwall areas in 9 Chinese coal mines. The ultimate surface subsidence factors vary from 0.10 to 0.15. This method has a great potential to be popularized and performed where longwall mining are implemented under villages and ground infrastructures.
基金National Science and Technology Supporting Program(2012BAB13B01)National Key Scientific Instrument and Equipment Development Program(2012YQ030126)+2 种基金Coal United Project of National Natural Science Foundation(U1261203)China Geological Survey Project(1212011220798)National Science and Technology Major Project(2011ZX05035-004-001HZ).
文摘To study the impact of modern coal mining on overlying strata and its water bearing conditions,integrated time-lapse geophysical prospecting integrating 3D seismic,electrical and ground penetrating radar method were used.Through observing and analyzing the geophysical data variations of all stages of pre-mining,mining and post-mining as well as post-mining deposition stable period,impacts of coal mining on stratigraphic structure and its water bearing were studied and modern coal mining induced stratigraphic change pattern was summarized.The research result shows that the stratigraphic structure and the water bearing of surface layer during modern coal mining have self-healing pattern with mining time;the self-healing capability of near-surface strata is relatively strong while the roof weak;water bearing selfhealing of near-surface strata is relatively high while the roof strata adjacent to mined coal beds low.Due to integrated time-lapse geophysical prospecting technology has extra time dimension which makes up the deficiency of static analysis of conventional geophysical methods,it can better highlight the dynamic changes of modern coal mining induced overburden strata and its water bearing conditions.
文摘The management of overburden is an important task in open pit exploitations. Site topography and morphology as well as geological and geotechnical properties of natural and remoulded materials are the most important factors affecting the disposal phase. Economic and environmental requirements must be followed in order to achieve the best reclamation results, keeping into account site constraints such as slope stability, hauling and dumping issues, and interactions with groundwater. This paper deals with the above mentioned issues, illustrating a rational approach applied on the case of a large limestone quarry where the thickness of the overburden is relevant and the spoil material has to be dumped in a flooded pit. The proposed multidisciplinary approach led to the selection of most suitable methods for excavation, transportation and disposal. The selection was based on a detailed laboratory and site characterisation that defined favorable and adverse factors to be considered during the preliminary study of a large quarrying project.
文摘A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7 ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey(USGS) in 2016.Further investigations by the National Institute for Occupational Safety and Health(NIOSH) and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia.Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity.In order to use the geology as a forecaster of mining-induced seismic events and their energy potential, two primary components are needed.The first component is a long history of recorded seismic events with accurately plotted locations.The second component is a high density of geologic data within the mining area.In this case, 181 events of 1.0 MLor greater were recorded by the mine's seismic network between January, 2009, and October, 2016.Within the mining area, 897 geophysical logs, 224 core holes, and 1031 fiberscope holes were examined by mine geologists.From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations.After the data was analyzed, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions.Three forecast maps were created based on geology of previous seismic locations.The forecast maps have shown an accuracy of within 74%–89% when compared to the recorded 181 events that were1.0 MLor greater when considering three major geological criteria of overburden thickness of 579.12 m or greater, 6.096–12.192 m of sandstone within 15.24 m of the Pocahontas number 3 seam, and a longwall caving height of 4.572 m or less.
基金provided by the National Natural Science Foundation of China(No.51674132)the State Key Research Development Program of China(No.2016YFC0801407-2)+3 种基金the Research Fund of The State Key Laboratory of Coal Resources and Safe Mining,CUMT(No.SKLCRSM15KF04)Natural Science Foundation of Liaoning Province(No.2015020614)Liaoning BaiQianWan Talents Program(No.201575)the Research Fund of State and Local Joint Engineering Laboratory for Gas Drainage & Ground Control of Deep Mines(Henan Polytechnic University)(No.G201602)
文摘Mining induced pressures are strong and overburden failure areas are large in top coal caving longwall mining, which constrains high production and safety mining. By employing the combination of the full view borehole photography technique and the seismic CT scanner technique, the deformation and failure of overlying strata of fully mechanized caving face in shallow coal seam were studied and the failure development of overburden was determined. Results show that the full view borehole photography can reveal the characteristics of strata, and the seismic CT scanner can reflect the characteristics of strata between the boreholes. The combined measurement technique can effectively determine the height of fractured and caved zones. The top end of the caved zone in Yangwangou coal mine employing the top coal caving longwall mining was at the depth of 171 m and fractured zone was at the depth of 106-110 m. The results provide a theoretic foundation for controlling the overburden strata in the shallow buried top coal caving panel.
基金The research work in this paper is financially supported by the West Virginia Coal and Energy Research Bureau(CERB).
文摘The broad objective of this research was to improve current surface mining practices and reduce negative environmental impact of overburden removal in West Virginia(WV).The specific objectives were to(i)compare conventional surface mining method(drilling,blasting,digging,and loading)to a surface miner(SM)method,and(ii)apply the analytical hierarchy process(AHP)to help select the optimal mining method based on production,cost and environmental criteria.The design and the procedures used in this research involve five interrelated modules:(i)rock properties of overburden in WV,(ii)drilling and blasting,(iii)digging and loading,(iv)SM method,and(v)comparative analysis and selection of the optimal mining method by AHP.Results of this research indicate that application of SM method would yield higher cost of overburden removal than conventional mining methods in rocks with a high unconfined compressive strength and abrasivity.A significant advantage of SM method,where applicable,is the elimination of the negative environmental impacts associated with blasting.
基金SERBDSTGovernment of India for funding this research work
文摘The effect of slope angle for external overburden dump in response to average and heavy rainfall has been analyzed using a two dimensional finite difference method of transient water flow through unsaturated–saturated soil. The external dump stability is evaluated for five geomaterial types on the basis of globally accepted safety factor analysis technique, based on shear strength reduction approach using finite difference method. The results obtained from the finite difference method of analysis indicate that the external dump with more than 30° slope angle is greatly influenced by the rainfall under the studied conditions for geomaterial 3, 4 and 5, whereas dumps with geomaterial 1 and 2 remain safe. The analysis shows that major slope failure is out of preview for the studied rainfall conditions.
文摘Rock typing is an important tool in evaluation and performance prediction of reservoirs.Different techniques such as flow zone indicator(FZI),FZI~*and Winland methods are used to categorize reservoir rocks into distinct rock types.Generally,these methods are applied to petrophysical data that are measured at a pressure other than reservoir pressure.Since the pressure changes the pore structure of rock,the effect of overburden pressure on rock typing should be considered.In this study,porosity and permeability of 113 core samples were measured at five different pressures.To investigate the effect of pressure on determination of rock types,FZI,FZI~*and Winland methods were applied.Results indicated that although most of the samples remain in the same rock type when pressure changes,some of them show different trends.These are related to the mineralogy and changes in pore system of the samples due to pressure change.Additionally,the number of rock types increases with increasing pressure.Furthermore,the effect of overburden pressure on determination of rock types is more clearly observed in the Winland and FZI~*methods.Also,results revealed that a more precise reservoir dynamic simulation can be obtained by considering the reservoir rock typing process at reservoir conditions.
基金funding support from the National Natural Science Foundation of China (Grant No. 42225702)the Central Government Guided Local Science and Technology Development Fund (Grant No. 226Z5404G)the Natural Science Foundation of Hebei Province,China (Grant No. D2022508002)。
文摘Understanding the spatiotemporal evolution of overburden deformation during coal mining is still a challenge in engineering practice due to the limitation of monitoring techniques. Taking the Yangliu Coal Mine as an example, a similarity model test was designed and conducted to investigate the deformation and failure mechanism of overlying rocks in this study. Distributed fiber optic sensing(DFOS), highdensity electrical resistivity tomography(HD-ERT) and close-range photogrammetry(CRP) technologies were used in the test for comprehensive analyses. The combined use of the three methods facilitates the investigation of the spatiotemporal evolution characteristics of overburden deformation, showing that the mining-induced deformation of overburden strata was a dynamic evolution process. This process was accompanied by the formation, propagation, closure and redevelopment of separation cracks.Moreover, the key rock stratum with high strength and high-quality lithology played a crucial role in the whole process of overburden deformation. There were generally three failure modes of overburden rock layers, including bending and tension, overall shearing, and shearing and sliding. Shear failure often leads to overburden falling off in blocks, which poses a serious threat to mining safety. Therefore, realtime and accurate monitoring of overburden deformation is of great significance for the safe mining of underground coal seams.
基金supported by the National Natural Science Foundation of China(51504081,51704095,51374201)the National Key Research and Development Program of China(2017YFC0805202)+3 种基金the Scientific Research Key Project Fund of Education Department of Henan Province(18A440012,14A440001)the Research Fund of Henan Key Laboratory for Green and Efficient Mining and Comprehensive Utilization of Mineral Resources(S201619)the Research Fund of the State Key Laboratory of Coal Resources and Safe Mining(13KF02)the Ph.D.Programs Foundation of Henan Polytechnic University(B2014-50,B2016-67).
文摘The backfilling mining technology is a type of high-efficiency coal mining technology that is used to address the environmental issues caused by the caving mining technology.In this paper,the mechanical model of symmetrical laminated plate representing the overburden movement caused by the backfilling mining technology is established,and the governing differential equation of the motion of the overburden is derived.The boundary conditions of the mechanical model are put forward,and the analytical solution of the overburden movement and surface subsidence is obtained.The numerical model of the overburden movement and surface subsidence,under mining with backfilling,is established by means of the FLAC3D numerical software,which aims to systematically study the influence of backfilling compactness,mining thickness,and mining depth on the overburden movement and surface subsidence in backfilling mining.When the compactnessηis less than 70%,the overburden movement and surface subsidence is greater,while whenηis greater than 70%,the overburden movement and surface subsidence is reduced significantly.On this basis,the control mechanism of surface subsidence and overburden movement in backfilling mining is obtained.The suitable backfilling compactness is the key to controlling surface subsidence and overburden movement in backfilling mining.
文摘Reservoir quality from cored intervals has traditionally been described by grouping similar intervals according to rock type. The main shortcoming of this static modelling approach is that it lacks clarity and it is not conducive for setting up a dynamic simulation model. The alternative is to use a modelling approach based on Hydraulic Flow Zone Units (HFZUs). First proposed in the late 1980s and extensively published in the early 1990s such formulation uses the well-known Carman-Kozeny (C-K) equation. More recently, this approach has been extended to cover a wider range of geological formations with diverse pore structure types. In using a HFZU approach, a pre-processing step is customarily undertaken to first overburden correct the data and where necessary also to correct for the Klinkenberg effect (lower permeability formations, lab testing with gas). The study presented compares corrected and uncorrected data sets, to see if correction alters the overall outcome of HFZU analysis. Specifically, data sets are compared at three different conditions: ambient, overburden (only) corrected and finally data that has been corrected for both, overburden and Klinkenberg effects. In all cases it is the Flow Zone Indicator (FZI), an index representative of formation quality that is tracked, together with the type of relationship. Several comparative analysis examples are given for diverse formations. The results show that uncorrected data can yield a different correlation and FZI, especially for intervals that include low permeability samples. Results indicate that Overburden and Klinkenberg corrections should be applied before HFZU analysis.
文摘Coal pillar design has historically assigned a factor of safety(Fo S) or stability factor(SF) according to their estimated strength and the assumed overburden load acting on them. Acceptable Fo S values have been assigned based on past mining experience or a statistical link between Fo S and probability of failure(Po F). Pillar width-to-height(w/h) ratio has long been established as having a material influence on both pillar strength and its potential failure mode. However, there has been significant disagreement on using both factor of safety(Fo S) and w/h as part of pillar system stability criterion, as compared to using Fo S in isolation. This paper will argue that there are valid technical reasons to bring w/h ratio into system stability criteria(other than its influence on pillar strength), as it is related to the post-failure stiffness of the pillar, as measured in situ, and its interaction with overburden stiffness. When overburden stiffness is also brought into pillar system stability considerations, two issues emerge. The first is the width-todepth(W/D) ratio of the panel and whether it is sub-critical or super-critical from a surface subsidence perspective. The second relates to a re-evaluation of pillar Fo S based on whether the pillar is in an elastic or non-elastic(i.e., post-yield) state in its as-designed condition, as this is relevant to maintaining overburden stiffness at the highest possible level. The significance of the model is the potential to maximise both reserve recovery and mining efficiencies without any discernible increase in geotechnical risk, particularly in thick seams and higher depth of cover mining situations. At a time when mining economics are, at best, marginal, removing potentially unnecessary design conservatism is of interest to all mine operators and is an important topic for discussion amongst the geotechnical community.
