A new scour countermeasure using solidified slurry for offshore foundation has been proposed recently.Fluidized solidified slurry is pumped to seabed area around foundation for scour protection or pumped into the deve...A new scour countermeasure using solidified slurry for offshore foundation has been proposed recently.Fluidized solidified slurry is pumped to seabed area around foundation for scour protection or pumped into the developed scour holes for scour repair as the fluidized material solidifies gradually.In the pumping operation and solidification,the engineering behaviors of solidified slurry require to be considered synthetically for the reliable application in scour repair and protection of ocean engineering such as the pumpability related flow value,flow diffusion behavior related rheological property,anti-scour performance related retention rate in solidification and bearing capacity related strength property after solidification.In this study,a series of laboratory tests are conducted to investigate the effects of mix proportion(initial water content and binder content)on the flow value,rheological properties,density,retention rate of solidified slurry and unconfined compressive strength(UCS).The results reveal that the flow value increases with the water content and decreases with the binder amount.All the solidified slurry exhibits Bingham plastic behavior when the shear rate is larger than 5 s^(-1).The Bingham model has been employed to fit the rheology test results,and empirical formulas for obtaining the density,yield stress and viscosity are established,providing scientific support for the numerical assessment of flow and diffusion of solidified slurry.Retention rate of solidified slurry decreases with the water flow velocity and flow value,which means the pumpability of solidified slurry is contrary to anti-scour performance.The unconfined compressive strength after solidification reduces as the water content increases and binder content decreases.A design and application procedure of solidified soil for scour repair and protection is also proposed for engineering reference.展开更多
High pressure die casting(HPDC)AlSi10Mn Mg alloy castings are widely used in the automobile industry.Mg can optimize the mechanical properties of castings through heat treatment,while the release of thermal stress aro...High pressure die casting(HPDC)AlSi10Mn Mg alloy castings are widely used in the automobile industry.Mg can optimize the mechanical properties of castings through heat treatment,while the release of thermal stress arouses the deformation of large integrated die-castings.Herein,the development of non-heat treatment Al alloys is becoming the hot topic.In addition,HPDC contains externally solidified crystals(ESCs),which are detrimental to the mechanical properties of castings.To achieve high strength and toughness of non-heat treatment die-casting Al-Si alloy,we used AlSi9Mn alloy as matrix with the introduction of Zr,Ti,Nb,and Ce.Their influences on ESCs and mechanical properties were systematically investigated through three-dimensional reconstruction and thermodynamic simulation.Our results reveal that the addition of Ti increased ESCs'size and porosity,while the introduction of Nb refined ESCs and decreased porosity.Meanwhile,large-sized Al_3(Zr,Ti)phases formed and degraded the mechanical properties.Subsequent introduction of Ce resulted in the poisoning effect and reduced mechanical properties.展开更多
The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron mi...The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).展开更多
Recovery of the coal buried under buildings,railways and water bodies and the residual coal in irregularly arranged fully mechanized mining faces is a common engineering problem facing underground coal mining.In this ...Recovery of the coal buried under buildings,railways and water bodies and the residual coal in irregularly arranged fully mechanized mining faces is a common engineering problem facing underground coal mining.In this study,a mining technology of continuous driving and gangue backfilling(CDGB)was proposed.The technology,which can not only alleviate ground subsidence and gangue discharge,but also release the above-mentioned coals,contributes to green and efficient sustainable development of mining.The stability of the system of the solidified body-reserved coal pillar combination(S-C combination)is crucial to the CDGB technology.Therefore,it is of great significance to explore the mechanical and damage characteristics of S-C combination in the synergistic bearing process.First,four sets of differentshaped S-C combination specimens were fabricated and a S-C combination bearing structure in CDGB was constructed to explore the differences in mechanical characteristics and damage modes of different-shaped S-C combination specimens during CDGB.Subsequently,their surface strain field evolutions and acoustic emission(AE)response characteristics in the load-bearing process were obtained with the aid of the digital image correlation technique and the AE signal monitoring system.Furthermore,a damage evolution model based on AE parameters and mechanical parameters was established to clarify the damage evolution law.The following results were obtained:(1)The free area of S-C combination can serve as a quantitative index to evaluate the stability of the overburden control system;(2)The concept of critical value k of the free area was first proposed.When the free area exceeds the critical value k(free area ratio greater than 1.13),the deformation resistance and the free area changes becomes negatively correlated;(3)As the free area expands,the failure of the S-C combination specimen evolves from tensile failure to shear failure.The distribution characteristics of the axial strain field also verified such a change in the failure mode;(4)When the free area expands,the peak AE count gradually changes from“double peaks”to“a single peak”.In this process,the expansion of free area shortens the time for accumulating and releasing energy during loading.Micro cracks generated in the specimen change from a phased steep growth to a continuous increase,and the process in which micro cracks develop,converge,intersect and connect to form macro cracks accelerates.The damage evolution law concluded based on AE parameters and mechanical parameters can well characterize the damage evolution process of S-C combination,providing certain reference for the study on the synergistic bearing of S-C combination during CDGB.展开更多
Foamed Polyurethane Solidified Ballasted Track(FPSBT),an innovative railway track,is formed by solidifying ballast bed with foamed polyurethane.Compared with the traditional Discrete Ballasted Track(DBT),FPSBT does no...Foamed Polyurethane Solidified Ballasted Track(FPSBT),an innovative railway track,is formed by solidifying ballast bed with foamed polyurethane.Compared with the traditional Discrete Ballasted Track(DBT),FPSBT does not require regular maintenance such as tamping and cleaning.However,limited studies exist on the mechanical properties of FPSBT.In this study,Laboratory experiments are conducted on polyurethane samples to investigate the effects of polyurethane density on the mechanical properties of FPSBT.Furthermore,the performance of DBT and FPSBT with different polyurethane densities are compared,and the recommended polyurethane density is obtained.FPSBT exhibited negligible accumulation of deformation under cyclic loads,indicating excellent performance of FPSBT owing to the anti-deformation properties of polyurethane.Further,a track load vehicle test is conducted.FPSBT exhibited better load-transmitting ability than DBT.Finally,the construction and application of FPSBT in China are introduced.This study is expected to contribute to realizing a more extensive application of FPSBT.展开更多
Standard mechanical test bars with a diameter of 6.4 mm and a gauge length of 50 mm were processed, and the microstructures of die cast AM60B alloy under different die casting process parameters were observed. The inf...Standard mechanical test bars with a diameter of 6.4 mm and a gauge length of 50 mm were processed, and the microstructures of die cast AM60B alloy under different die casting process parameters were observed. The influences of the slow shot speed, the fast shot speed and the biscuit thickness on the externally solidified crystals （ESCs） were investigated. With the increase of the biscuit thickness, the number of the ESCs in the cast samples decreases. Under a low slow shot speed, larg ESCs are found in the cast structure and a high fast shot speed results in more spherical ESCs. The relationships between ESCs and process parameters were also discussed.展开更多
The effects of a pulsed magnetic field on the solidified microstructure of an AZ31 magnesium alloy were investigated.The experimental results show that the remarkable microstructural refinement is achieved when the pu...The effects of a pulsed magnetic field on the solidified microstructure of an AZ31 magnesium alloy were investigated.The experimental results show that the remarkable microstructural refinement is achieved when the pulsed magnetic field is applied to the solidification of the AZ31 alloy.The average grain size of the as-cast microstructure of the AZ31 alloy is refined to 107 μm.By quenching the AZ31 alloy, the different primary α-Mg microstructures are preserved during the course of solidification.The microstructure evolution reveals that the primary α-Mg generates and grows in globular shape with pulsed magnetic field, contrast with the dendritic shape without pulsed magnetic field.The pulsed magnetic field causes melt convection during solidification, which makes the temperature of the whole melt homogenized, and produces an undercooling zone in front of the liquid/solid interface, which makes the nucleation rate increased and big dendrites prohibited.In addition, the Joule heat effect induced in the melt also strengthens the grain refinement effect and spheroidization of dendrite arms.展开更多
The structure and properties of Cu-Cr-Zr alloy were studied after rapidly solidified aging and solid solution aging.At the early stage of aging （500℃ for 15 rain）, the hardness and the conductivity of the alloy rap...The structure and properties of Cu-Cr-Zr alloy were studied after rapidly solidified aging and solid solution aging.At the early stage of aging （500℃ for 15 rain）, the hardness and the conductivity of the alloy rapidly solidified are 143 HV and 72% IACS, respectively. Under the same aging condition, the hardness and electrical conductivity of the alloy solid solution treated can reach 86 HV and 47% IACS, respectively. The microstructure was analyzed, and the grain size after rapid solidification is much smaller than that after solid solution treatment. By rapidly solidified aging the fine precipitates distribute inside the grains and along the grain boundary, while by solid solution aging there are large Cr particles along the grain boundary.展开更多
The (100) texture of solidified fcc metals, caused by the preferential (100) dendrite growth, could be closeIy related to solid/melt interfaces which behave differently along different crystallographic orientation. Th...The (100) texture of solidified fcc metals, caused by the preferential (100) dendrite growth, could be closeIy related to solid/melt interfaces which behave differently along different crystallographic orientation. The stability and roughness of {111} and {100} solid/melt interfaces of fcc metals were investigated using a modified Temkin multi-layer model. It is demonstrated that {100}crystal/melt interface is more unstable and rougher than {111} interface. The effect of the stability of crystal/melt interface on the (100) texture formation in solidified fcc metals has been analysed and discussed.展开更多
The solidified structure of the thin-walled and complicated Ti-6AI-4V castings produced by the vertical centrifugal casting process was studied in the present work. The results show that the wall thickness of the sect...The solidified structure of the thin-walled and complicated Ti-6AI-4V castings produced by the vertical centrifugal casting process was studied in the present work. The results show that the wall thickness of the section is featured with homogeneously distributed fine equiaxial grains, compared with the microstructure of the thick-walled section. The grain size of the castings has a tendency to decrease gradually with the increasing of the centrifugal radius. The inter-lamellar space in thick-walled casting parts is bigger than that of the thin-walled parts, and the profile of inter-lamellar space is not susceptible to the centrifugal radius.展开更多
A rapidly solidified Al-2.5Ti-2.5Fe-2.5Cr (mass fraction in percent) alloywas prepared by melt spinning. As-quenched and as-annealed microstructures were studied by X-raydiffractometry (XRD), transmission electron mic...A rapidly solidified Al-2.5Ti-2.5Fe-2.5Cr (mass fraction in percent) alloywas prepared by melt spinning. As-quenched and as-annealed microstructures were studied by X-raydiffractometry (XRD), transmission electron microscopy (TEM), high-resolution transmission electronmicroscopy (HREM) and energy dispersive spectrum (EDS) analysis. The microhardness of the alloy atdifferent annealing temperatures was measured. The results obtained indicate that the microhardnessof the rapidly solidified Al-2.5Ti-2.5Fe-2.5Cr alloy does not vary with different annealingtemperatures. The as-quenched microstructure of the alloy includes two kinds of dispersed primaryphases: Al_3Ti and Al_(13)(Cr, Fe)_2. After annealing at 400 deg C for 10 h, the stable phaseAl_(13)Fe_4 appears in the microstructure.展开更多
Rapidly solidified Al-Ti base alloys were prepared by melt spinning at the cooling rate about 107 K/s. The melt-spun ribbons were used to observe the dricrostructures after heat treatment.In the supersaturated Al-Tl-S...Rapidly solidified Al-Ti base alloys were prepared by melt spinning at the cooling rate about 107 K/s. The melt-spun ribbons were used to observe the dricrostructures after heat treatment.In the supersaturated Al-Tl-Si alloy, age hardening occurred after 1 h anneal in the temperature range of 4000~500℃, which seems to be attributed to the precipitation of metastable Ll2- (Al,Si)3Ti phase. However. the microhardness was relatively low because of the low v/o and the insufflcient stability of precipitates. Thus. Cr was added to Al-Ti-Si alloys in order to stabilize the microstructures and to increase the v/o of precipitate5. As a result. the alIoys containing Cr were evaluated to possess the improved properties at the service temperature.展开更多
Al2O3/A356-La alloy composites were fabricated by squeeze casting, and the effects of La on the solidified structure and the solute segregation during alloy solidification were studied. The results indicate that the s...Al2O3/A356-La alloy composites were fabricated by squeeze casting, and the effects of La on the solidified structure and the solute segregation during alloy solidification were studied. The results indicate that the structure of the matrix alloy becomes fine and small by the addition of La. La has been richened at the interface to help improve the wettability between the fiber and Al alloy, but there are no intermetallic compounds richening La found at the interface yet. There is no special influence of La on the Mg segregation in the matrix alloy. The distribution of Mg and La in the composites has been at the same position--near the interface.展开更多
In order to efficiently seal air leakages and control spontaneous combustion of coal, solidified foam was developed by adding a certain compound additive to fly coal ash and cement as the main materials. It was prepar...In order to efficiently seal air leakages and control spontaneous combustion of coal, solidified foam was developed by adding a certain compound additive to fly coal ash and cement as the main materials. It was prepared basing on the foaming characteristic through physical and mechanical system. We studied the effects of the different types of foaming agents, the mass ratio of cement to fly ash, and the mass ratio of solid to water and content of cellulose on the performance of solidified foam. The results show that when adding the composite protein, surfactant and cellulose foaming agents. The cement-fly ash ratio of 0.75:1, the water solid ratio as large as 2:1, and the solidified foam with high properties and density of only 516 kg/m 3 and compressive strength of up to 12.68 MPa were prepared. But the initial setting time, identity and compressive strength may be changed by varying the water solid ratio and/or the additives. We theoretically analyzed the influence mechanism of foam density, compressive strength and water solid ratio. The solidified foam is especially suitable for sealing surface leakage channels and filling the goaf with a wide application prospects.展开更多
Through unconfined compressive strength test,influencing factors on compressive strength of solidified inshore saline soil with SH lime-ash,ratio of lime-ash(1-K),quantity of lime-ash,age,degree of compression and sal...Through unconfined compressive strength test,influencing factors on compressive strength of solidified inshore saline soil with SH lime-ash,ratio of lime-ash(1-K),quantity of lime-ash,age,degree of compression and salt content were studied.The results show that because inshore saline soil has special engineering characteristic,more influencing factors must be considered compared with ordinary soil for the perfect effect of solidifying.展开更多
Every year, a large amount of silt is generated by river dredging. For the characteristics of dredging silt, such as high moisture content, low strength and high compressibility, the traditional solidification method ...Every year, a large amount of silt is generated by river dredging. For the characteristics of dredging silt, such as high moisture content, low strength and high compressibility, the traditional solidification method can no longer better solve this kind of silt problem.?This paper mainly studies the fluidized solidification treatment of high water content sludge, not only makes the silt soil achieve a good solidification effect, but also the project cost is lower, the construction method is more environmentally friendly and green. The influencing factors of the solidified soil are mainly investigated by the unconfined compression test and the fluidity test. The experiment result shows?1)When the cement to sludge mass ratio (RCS) is 0.09?-?0.16 and the fly ash to cement mass ratio (RFC) is 0.35?-?0.80, as the amount of?RFC?increases, the flow rate of the solidified soil gradually decreases. With the increase of time, the liquidity is significantly reduced, and the influence of cement on the fluidity is greater than that of fly ash.?2) When?RCS?= 0.09?-?0.16, the strength of the sludge solidified soil at 28?d age increased by 4.5?-?6 times. 3)?When?RCS?= 0.09?-?0.16 and?RFC?= 35%?-?80%, the intensity of 14?d increased by 1.23 times than that of 7?d, and the intensity of 28 days increased by 1.29 times than that of 14?d. This experiment can provide the mix ratio design of solidified materials for different needs of the project, which can better provide a basis for engineering application and strength prediction.展开更多
During the cold-chamber high pressure die casting(HPDC) process, samples were produced to investigate the microstructure characteristics of AM60B magnesium alloy. Special attention was paid to the effects of process p...During the cold-chamber high pressure die casting(HPDC) process, samples were produced to investigate the microstructure characteristics of AM60B magnesium alloy. Special attention was paid to the effects of process parameters on the morphology and distribution of externally solidified crystals(ESCs) in the microstructure of magnesium alloy die castings, such as slow shot phase plunger velocity, delay time of pouring and fast shot phase plunger velocity. On the basis of metallographic observation and quantitative statistics, it is concluded that a lower slow shot phase plunger velocity and a longer delay time of pouring both lead to an increment of the size and percentage of the ESCs, due to the fact that a longer holding time of the melt in the shot sleeve will cause a more severe loss of the superheat. The impingement of the melt flow on the ESCs is more intensive with a higher fast shot phase plunger velocity, in such case the ESCs reveal a more granular and roundish morphology and are dispersed throughout the cross section of the castings. Based on analysis of the filling and solidification processes of the melt during the HPDC process, reasonable explanations were proposed in terms of the nucleation, growth, remelting and fragmentation of the ESCs to interpret the effects of process parameters on the morphology and distribution of the ESCs in the microstructure of magnesium alloy die castings.展开更多
Rapidly solidified Al92.3Fe4.3V0.7Si1.7Mm1.0 alloy has been studied by positron lifetime spectroscopy and the variations on the intedecial defects with the annealing temperature were revealed by an analysis of the lif...Rapidly solidified Al92.3Fe4.3V0.7Si1.7Mm1.0 alloy has been studied by positron lifetime spectroscopy and the variations on the intedecial defects with the annealing temperature were revealed by an analysis of the lifetime results. The intedece characteristics derived from the positron-lifetime results could be used to give a satisfactory interpretation of the dependence of mechanical properties on the annealing temperature展开更多
The investigation of the long-term performance of solidified/stabilized （S/S） contaminated soils was carried out in a trial site in southeast UK. The soils were exposed to the maximum natural weathering for four yea...The investigation of the long-term performance of solidified/stabilized （S/S） contaminated soils was carried out in a trial site in southeast UK. The soils were exposed to the maximum natural weathering for four years and sampled at various depths in a controlled manner. The chemical properties （e.g., degree of carbonation （DOC）, pH, electrical conductivity （EC）） and physical properties （e.g., moisture content （MC）, liquid limit CLL）, plastic limit （PL）, plasticity index （PI）） of the samples untreated and treated with the traditional and accelerated carbonated S/S processes were analyzed. Their variations on the depths of the soils were also studied. The result showed that the broad geotechnical properties of the soils, manifested in their PIs, were related to the concentration of the water soluble ions and in particular the free calcium ions. The samples treated with the accelerated carbonation technology （ACT）, and the untreated samples contained limited number of free calcium ions in solutions and consequently interacted with waters in a similar way. Compared with the traditional cement-based S/S technology, e.g., treatment with ordinary portland cement （OPC） or EnvirOceM, ACT caused the increase of the PI of the treated soil and made it more stable during long-term weathering. The PI values for the four soils ascended according to the order： the EnvirOceM soil, the OPC soil, the ACT soil, and the untreated soil while their pH and EC values descended according to the same order.展开更多
The rheological behavior of partially solidified Al-10% Cu alloy is in-vestigated.It is found that the slurry presents the character of a psoudoplastie fluid inisothermally holding and the apparent viscosity increases...The rheological behavior of partially solidified Al-10% Cu alloy is in-vestigated.It is found that the slurry presents the character of a psoudoplastie fluid inisothermally holding and the apparent viscosity increases with increasing cooling ratein continuously cooling.The effect of cooling rate on the apparent viscosity decreasesin high stirring rate range.The measured value of apparent viscosity is influenced bythe diameter of the screw propeller.展开更多
基金financially supported by the Science and Technology Commission Foundation of Shanghai(Grant Nos.22DZ1208903,20DZ2251900)the National Natural Science Foundation of China(Grant No.51679134)。
文摘A new scour countermeasure using solidified slurry for offshore foundation has been proposed recently.Fluidized solidified slurry is pumped to seabed area around foundation for scour protection or pumped into the developed scour holes for scour repair as the fluidized material solidifies gradually.In the pumping operation and solidification,the engineering behaviors of solidified slurry require to be considered synthetically for the reliable application in scour repair and protection of ocean engineering such as the pumpability related flow value,flow diffusion behavior related rheological property,anti-scour performance related retention rate in solidification and bearing capacity related strength property after solidification.In this study,a series of laboratory tests are conducted to investigate the effects of mix proportion(initial water content and binder content)on the flow value,rheological properties,density,retention rate of solidified slurry and unconfined compressive strength(UCS).The results reveal that the flow value increases with the water content and decreases with the binder amount.All the solidified slurry exhibits Bingham plastic behavior when the shear rate is larger than 5 s^(-1).The Bingham model has been employed to fit the rheology test results,and empirical formulas for obtaining the density,yield stress and viscosity are established,providing scientific support for the numerical assessment of flow and diffusion of solidified slurry.Retention rate of solidified slurry decreases with the water flow velocity and flow value,which means the pumpability of solidified slurry is contrary to anti-scour performance.The unconfined compressive strength after solidification reduces as the water content increases and binder content decreases.A design and application procedure of solidified soil for scour repair and protection is also proposed for engineering reference.
基金financially supported by the National Natural Science Foundation of China(Nos.52175284 and 52474396)the National Key Research and Development Program of China(No.2022YFB3404201)。
文摘High pressure die casting(HPDC)AlSi10Mn Mg alloy castings are widely used in the automobile industry.Mg can optimize the mechanical properties of castings through heat treatment,while the release of thermal stress arouses the deformation of large integrated die-castings.Herein,the development of non-heat treatment Al alloys is becoming the hot topic.In addition,HPDC contains externally solidified crystals(ESCs),which are detrimental to the mechanical properties of castings.To achieve high strength and toughness of non-heat treatment die-casting Al-Si alloy,we used AlSi9Mn alloy as matrix with the introduction of Zr,Ti,Nb,and Ce.Their influences on ESCs and mechanical properties were systematically investigated through three-dimensional reconstruction and thermodynamic simulation.Our results reveal that the addition of Ti increased ESCs'size and porosity,while the introduction of Nb refined ESCs and decreased porosity.Meanwhile,large-sized Al_3(Zr,Ti)phases formed and degraded the mechanical properties.Subsequent introduction of Ce resulted in the poisoning effect and reduced mechanical properties.
基金financially supported by the National Key Research and Development Program of China(2022YFB3404201)the Major Science and Technology Project of Changchun City,Jilin Province(Grant No.20210301024GX)。
文摘The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).
基金the National Natural Science Foundation of China(Nos.U21A20108,52322403,52174108,and 51974105)the Support Plan for Science&Technology Innovation Talents in Universities of Henan Province(No.21HASTIT024)+1 种基金the Scientific and technological innovation research team of Henan Polytechnic University(No.T2021-5)the Henan Excellent Youth Science Foundation(No.222300420045).
文摘Recovery of the coal buried under buildings,railways and water bodies and the residual coal in irregularly arranged fully mechanized mining faces is a common engineering problem facing underground coal mining.In this study,a mining technology of continuous driving and gangue backfilling(CDGB)was proposed.The technology,which can not only alleviate ground subsidence and gangue discharge,but also release the above-mentioned coals,contributes to green and efficient sustainable development of mining.The stability of the system of the solidified body-reserved coal pillar combination(S-C combination)is crucial to the CDGB technology.Therefore,it is of great significance to explore the mechanical and damage characteristics of S-C combination in the synergistic bearing process.First,four sets of differentshaped S-C combination specimens were fabricated and a S-C combination bearing structure in CDGB was constructed to explore the differences in mechanical characteristics and damage modes of different-shaped S-C combination specimens during CDGB.Subsequently,their surface strain field evolutions and acoustic emission(AE)response characteristics in the load-bearing process were obtained with the aid of the digital image correlation technique and the AE signal monitoring system.Furthermore,a damage evolution model based on AE parameters and mechanical parameters was established to clarify the damage evolution law.The following results were obtained:(1)The free area of S-C combination can serve as a quantitative index to evaluate the stability of the overburden control system;(2)The concept of critical value k of the free area was first proposed.When the free area exceeds the critical value k(free area ratio greater than 1.13),the deformation resistance and the free area changes becomes negatively correlated;(3)As the free area expands,the failure of the S-C combination specimen evolves from tensile failure to shear failure.The distribution characteristics of the axial strain field also verified such a change in the failure mode;(4)When the free area expands,the peak AE count gradually changes from“double peaks”to“a single peak”.In this process,the expansion of free area shortens the time for accumulating and releasing energy during loading.Micro cracks generated in the specimen change from a phased steep growth to a continuous increase,and the process in which micro cracks develop,converge,intersect and connect to form macro cracks accelerates.The damage evolution law concluded based on AE parameters and mechanical parameters can well characterize the damage evolution process of S-C combination,providing certain reference for the study on the synergistic bearing of S-C combination during CDGB.
基金sponsored by the National Natural Science Foundation of China(Grant No.52278467)China State Railway Group Co.Ltd.(P2022G013)+1 种基金China Academy of Railway Sciences Co.Ltd.(2022QT002)the Beijing-Shanghai High Speed Railway Co.Ltd.(2022-16).
文摘Foamed Polyurethane Solidified Ballasted Track(FPSBT),an innovative railway track,is formed by solidifying ballast bed with foamed polyurethane.Compared with the traditional Discrete Ballasted Track(DBT),FPSBT does not require regular maintenance such as tamping and cleaning.However,limited studies exist on the mechanical properties of FPSBT.In this study,Laboratory experiments are conducted on polyurethane samples to investigate the effects of polyurethane density on the mechanical properties of FPSBT.Furthermore,the performance of DBT and FPSBT with different polyurethane densities are compared,and the recommended polyurethane density is obtained.FPSBT exhibited negligible accumulation of deformation under cyclic loads,indicating excellent performance of FPSBT owing to the anti-deformation properties of polyurethane.Further,a track load vehicle test is conducted.FPSBT exhibited better load-transmitting ability than DBT.Finally,the construction and application of FPSBT in China are introduced.This study is expected to contribute to realizing a more extensive application of FPSBT.
基金Project(2009AA03Z114)supported by the National High-tech Research and Development Program of ChinaProject supported by Tsinghua-Toyo R&D Center of Magnesium and Aluminum Alloys Processing Technology
文摘Standard mechanical test bars with a diameter of 6.4 mm and a gauge length of 50 mm were processed, and the microstructures of die cast AM60B alloy under different die casting process parameters were observed. The influences of the slow shot speed, the fast shot speed and the biscuit thickness on the externally solidified crystals （ESCs） were investigated. With the increase of the biscuit thickness, the number of the ESCs in the cast samples decreases. Under a low slow shot speed, larg ESCs are found in the cast structure and a high fast shot speed results in more spherical ESCs. The relationships between ESCs and process parameters were also discussed.
基金Project(ZC304009103) supported by the Doctoral Fund of Zhejiang Normal University,ChinaProject(KYJ06Y09157) supported by School-level Project of Zhejiang Normal University,China
文摘The effects of a pulsed magnetic field on the solidified microstructure of an AZ31 magnesium alloy were investigated.The experimental results show that the remarkable microstructural refinement is achieved when the pulsed magnetic field is applied to the solidification of the AZ31 alloy.The average grain size of the as-cast microstructure of the AZ31 alloy is refined to 107 μm.By quenching the AZ31 alloy, the different primary α-Mg microstructures are preserved during the course of solidification.The microstructure evolution reveals that the primary α-Mg generates and grows in globular shape with pulsed magnetic field, contrast with the dendritic shape without pulsed magnetic field.The pulsed magnetic field causes melt convection during solidification, which makes the temperature of the whole melt homogenized, and produces an undercooling zone in front of the liquid/solid interface, which makes the nucleation rate increased and big dendrites prohibited.In addition, the Joule heat effect induced in the melt also strengthens the grain refinement effect and spheroidization of dendrite arms.
基金This work was supported by the National“863”High Pro-gram of China(No.2002AA331112)the Doctorate Foun-dation of Northwestern Polytechnical University(CX200409)the Science Research Foundation of Henan University of Science and Technology(No.2004ZY039).
文摘The structure and properties of Cu-Cr-Zr alloy were studied after rapidly solidified aging and solid solution aging.At the early stage of aging （500℃ for 15 rain）, the hardness and the conductivity of the alloy rapidly solidified are 143 HV and 72% IACS, respectively. Under the same aging condition, the hardness and electrical conductivity of the alloy solid solution treated can reach 86 HV and 47% IACS, respectively. The microstructure was analyzed, and the grain size after rapid solidification is much smaller than that after solid solution treatment. By rapidly solidified aging the fine precipitates distribute inside the grains and along the grain boundary, while by solid solution aging there are large Cr particles along the grain boundary.
文摘The (100) texture of solidified fcc metals, caused by the preferential (100) dendrite growth, could be closeIy related to solid/melt interfaces which behave differently along different crystallographic orientation. The stability and roughness of {111} and {100} solid/melt interfaces of fcc metals were investigated using a modified Temkin multi-layer model. It is demonstrated that {100}crystal/melt interface is more unstable and rougher than {111} interface. The effect of the stability of crystal/melt interface on the (100) texture formation in solidified fcc metals has been analysed and discussed.
基金by the National Natural Science Foundation of China under grant No. 50775050the State Key Laboratory of Solidif ication Processing in NWPU (200702)
文摘The solidified structure of the thin-walled and complicated Ti-6AI-4V castings produced by the vertical centrifugal casting process was studied in the present work. The results show that the wall thickness of the section is featured with homogeneously distributed fine equiaxial grains, compared with the microstructure of the thick-walled section. The grain size of the castings has a tendency to decrease gradually with the increasing of the centrifugal radius. The inter-lamellar space in thick-walled casting parts is bigger than that of the thin-walled parts, and the profile of inter-lamellar space is not susceptible to the centrifugal radius.
文摘A rapidly solidified Al-2.5Ti-2.5Fe-2.5Cr (mass fraction in percent) alloywas prepared by melt spinning. As-quenched and as-annealed microstructures were studied by X-raydiffractometry (XRD), transmission electron microscopy (TEM), high-resolution transmission electronmicroscopy (HREM) and energy dispersive spectrum (EDS) analysis. The microhardness of the alloy atdifferent annealing temperatures was measured. The results obtained indicate that the microhardnessof the rapidly solidified Al-2.5Ti-2.5Fe-2.5Cr alloy does not vary with different annealingtemperatures. The as-quenched microstructure of the alloy includes two kinds of dispersed primaryphases: Al_3Ti and Al_(13)(Cr, Fe)_2. After annealing at 400 deg C for 10 h, the stable phaseAl_(13)Fe_4 appears in the microstructure.
文摘Rapidly solidified Al-Ti base alloys were prepared by melt spinning at the cooling rate about 107 K/s. The melt-spun ribbons were used to observe the dricrostructures after heat treatment.In the supersaturated Al-Tl-Si alloy, age hardening occurred after 1 h anneal in the temperature range of 4000~500℃, which seems to be attributed to the precipitation of metastable Ll2- (Al,Si)3Ti phase. However. the microhardness was relatively low because of the low v/o and the insufflcient stability of precipitates. Thus. Cr was added to Al-Ti-Si alloys in order to stabilize the microstructures and to increase the v/o of precipitate5. As a result. the alIoys containing Cr were evaluated to possess the improved properties at the service temperature.
基金This work was financially supported by the Chinese Ministry of Education (No. 00191) and the Natural Science Founda-tion of Jiangxi Province, China (No. 0150032)
文摘Al2O3/A356-La alloy composites were fabricated by squeeze casting, and the effects of La on the solidified structure and the solute segregation during alloy solidification were studied. The results indicate that the structure of the matrix alloy becomes fine and small by the addition of La. La has been richened at the interface to help improve the wettability between the fiber and Al alloy, but there are no intermetallic compounds richening La found at the interface yet. There is no special influence of La on the Mg segregation in the matrix alloy. The distribution of Mg and La in the composites has been at the same position--near the interface.
基金provided by the National Natural Science Foundation of China (No. 50904066)the Program for New Century Excellent Talents in University (No. NCET-09-0729)the National Excellent Doctoral Dissertation Special Fund (No. 2007B53)
文摘In order to efficiently seal air leakages and control spontaneous combustion of coal, solidified foam was developed by adding a certain compound additive to fly coal ash and cement as the main materials. It was prepared basing on the foaming characteristic through physical and mechanical system. We studied the effects of the different types of foaming agents, the mass ratio of cement to fly ash, and the mass ratio of solid to water and content of cellulose on the performance of solidified foam. The results show that when adding the composite protein, surfactant and cellulose foaming agents. The cement-fly ash ratio of 0.75:1, the water solid ratio as large as 2:1, and the solidified foam with high properties and density of only 516 kg/m 3 and compressive strength of up to 12.68 MPa were prepared. But the initial setting time, identity and compressive strength may be changed by varying the water solid ratio and/or the additives. We theoretically analyzed the influence mechanism of foam density, compressive strength and water solid ratio. The solidified foam is especially suitable for sealing surface leakage channels and filling the goaf with a wide application prospects.
基金Project(05YFSYSF00300) supported by the Natural Science Foundation of Tianjin
文摘Through unconfined compressive strength test,influencing factors on compressive strength of solidified inshore saline soil with SH lime-ash,ratio of lime-ash(1-K),quantity of lime-ash,age,degree of compression and salt content were studied.The results show that because inshore saline soil has special engineering characteristic,more influencing factors must be considered compared with ordinary soil for the perfect effect of solidifying.
文摘Every year, a large amount of silt is generated by river dredging. For the characteristics of dredging silt, such as high moisture content, low strength and high compressibility, the traditional solidification method can no longer better solve this kind of silt problem.?This paper mainly studies the fluidized solidification treatment of high water content sludge, not only makes the silt soil achieve a good solidification effect, but also the project cost is lower, the construction method is more environmentally friendly and green. The influencing factors of the solidified soil are mainly investigated by the unconfined compression test and the fluidity test. The experiment result shows?1)When the cement to sludge mass ratio (RCS) is 0.09?-?0.16 and the fly ash to cement mass ratio (RFC) is 0.35?-?0.80, as the amount of?RFC?increases, the flow rate of the solidified soil gradually decreases. With the increase of time, the liquidity is significantly reduced, and the influence of cement on the fluidity is greater than that of fly ash.?2) When?RCS?= 0.09?-?0.16, the strength of the sludge solidified soil at 28?d age increased by 4.5?-?6 times. 3)?When?RCS?= 0.09?-?0.16 and?RFC?= 35%?-?80%, the intensity of 14?d increased by 1.23 times than that of 7?d, and the intensity of 28 days increased by 1.29 times than that of 14?d. This experiment can provide the mix ratio design of solidified materials for different needs of the project, which can better provide a basis for engineering application and strength prediction.
基金financially supported by the Fundamental Research Funds for the Central Universities(WUT:2017IVA036)111 Project(B17034)State Key Laboratory of Materials Processing and Die&Mould Technology,Huazhong University of Science and Technology(P2018-003)
文摘During the cold-chamber high pressure die casting(HPDC) process, samples were produced to investigate the microstructure characteristics of AM60B magnesium alloy. Special attention was paid to the effects of process parameters on the morphology and distribution of externally solidified crystals(ESCs) in the microstructure of magnesium alloy die castings, such as slow shot phase plunger velocity, delay time of pouring and fast shot phase plunger velocity. On the basis of metallographic observation and quantitative statistics, it is concluded that a lower slow shot phase plunger velocity and a longer delay time of pouring both lead to an increment of the size and percentage of the ESCs, due to the fact that a longer holding time of the melt in the shot sleeve will cause a more severe loss of the superheat. The impingement of the melt flow on the ESCs is more intensive with a higher fast shot phase plunger velocity, in such case the ESCs reveal a more granular and roundish morphology and are dispersed throughout the cross section of the castings. Based on analysis of the filling and solidification processes of the melt during the HPDC process, reasonable explanations were proposed in terms of the nucleation, growth, remelting and fragmentation of the ESCs to interpret the effects of process parameters on the morphology and distribution of the ESCs in the microstructure of magnesium alloy die castings.
文摘Rapidly solidified Al92.3Fe4.3V0.7Si1.7Mm1.0 alloy has been studied by positron lifetime spectroscopy and the variations on the intedecial defects with the annealing temperature were revealed by an analysis of the lifetime results. The intedece characteristics derived from the positron-lifetime results could be used to give a satisfactory interpretation of the dependence of mechanical properties on the annealing temperature
文摘The investigation of the long-term performance of solidified/stabilized （S/S） contaminated soils was carried out in a trial site in southeast UK. The soils were exposed to the maximum natural weathering for four years and sampled at various depths in a controlled manner. The chemical properties （e.g., degree of carbonation （DOC）, pH, electrical conductivity （EC）） and physical properties （e.g., moisture content （MC）, liquid limit CLL）, plastic limit （PL）, plasticity index （PI）） of the samples untreated and treated with the traditional and accelerated carbonated S/S processes were analyzed. Their variations on the depths of the soils were also studied. The result showed that the broad geotechnical properties of the soils, manifested in their PIs, were related to the concentration of the water soluble ions and in particular the free calcium ions. The samples treated with the accelerated carbonation technology （ACT）, and the untreated samples contained limited number of free calcium ions in solutions and consequently interacted with waters in a similar way. Compared with the traditional cement-based S/S technology, e.g., treatment with ordinary portland cement （OPC） or EnvirOceM, ACT caused the increase of the PI of the treated soil and made it more stable during long-term weathering. The PI values for the four soils ascended according to the order： the EnvirOceM soil, the OPC soil, the ACT soil, and the untreated soil while their pH and EC values descended according to the same order.
文摘The rheological behavior of partially solidified Al-10% Cu alloy is in-vestigated.It is found that the slurry presents the character of a psoudoplastie fluid inisothermally holding and the apparent viscosity increases with increasing cooling ratein continuously cooling.The effect of cooling rate on the apparent viscosity decreasesin high stirring rate range.The measured value of apparent viscosity is influenced bythe diameter of the screw propeller.
