Reactive armour is a very efficient add-on armour against shaped charge threats.Explosive reactive armour consists of one or several plates that are accelerated by an explosive.Similar but less violent acceleration of...Reactive armour is a very efficient add-on armour against shaped charge threats.Explosive reactive armour consists of one or several plates that are accelerated by an explosive.Similar but less violent acceleration of plates can also be achieved in a completely inert reactive armour.To be efficient against elongated jets,the motion of the plates needs to be inclined against the jet such that a sliding contact between the jet and the plates is established.This sliding contact causes a deflection and thinning of the jet.Under certain circumstances,the contact will become unstable,leading to severe disturbances on the jet.These disturbances will drastically reduce the jet penetration performance and it is therefore of interest to study the conditions that leads to an unstable contact.Previous studies on the interaction between shaped charge jets and flyer plates have shown that it is mainly the forward moving plate in an explosive reactive armour that is effective in disturbing the jet.This is usually attributed to the higher plate-to-jet mass flux ratio involved in the collision of the forward moving plate compared to the backward moving plate.For slow moving plates,as occurs in inert reactive armour,the difference in mass flux for the forward and backward moving plate is much lesser,and it is therefore of interest to study if other factors than the mass flux influences on the protection capability.In this work,experiments have been performed where a plate is accelerated along its length,interacting with a shaped charge jet that is fired at an oblique angle to the plate’s normal,either against or along the plate’s velocity.The arrangement corresponds to a jet interacting with a flyer plate from a reactive armour,with the exception that the collision velocity is the same for both types of obliquities in these experiments.The experiments show that disturbances on the jet are different in the two cases even though the collision velocities are the same.Numerical simulations of the interaction support the observation.The difference is attributed to the character of the contact pressure in the interaction region.For a backward moving plate,the maximum contact pressure is obtained at the beginning of the interaction zone and the contact pressure is therefore higher upstream than downstream of the jet while the opposite is true for a forward moving plate.A negative interface pressure gradient with respect to the jet motion results in a more stable flow than a positive,which means that the jet-plate contact is more stable for a backward moving plate than for a forward moving plate.A forward moving plate is thus more effective in disturbing the jet than a backward moving plate,not only because of the higher jet to plate mass flux ratio but also because of the character of the contact with the jet.展开更多
Background The prospective association of dietary thiamine intake with the risk of cognitive decline among the general older adults remains uncertain.Aims To investigate the association between dietary thiamine intake...Background The prospective association of dietary thiamine intake with the risk of cognitive decline among the general older adults remains uncertain.Aims To investigate the association between dietary thiamine intake and cognitive decline in cognitively healthy,older Chinese individuals.Methods The study included a total of 3106 participants capable of completing repeated cognitive function tests.Dietary nutrient intake information was collected through 3-day dietary recalls and using a 3-day food-weighed method to assess cooking oil and condiment consumption.Cognitive decline was defined as the 5-year decline rate in global or composite cognitive scores based on a subset of items from the Telephone Interview for Cognitive Status-modified.Results The median follow-up duration was 5.9 years.There was a J-shaped relationship between dietary thiamine intake and the 5-year decline rate in global and composite cognitive scores,with an inflection point of 0.68 mg/day(95%confidence interval(Cl):0.56 to 0.80)and a minimal risk at 0.60-1.00 mg/day of dietary thiamine intake.Before the inflection point,thiamine intake was not significantly associated with cognitive decline.Beyond the inflection point,each unit increase in thiamine intake(mg/day)was associated with a significant decrease of 4.24(95%Cl:2.22 to 6.27)points in the global score and 0.49(95%Cl:0.23 to 0.76)standard units in the composite score within 5 years.A stronger positive association between thiamine intake and cognitive decline was observed in those with hypertension,obesity and those who were non-smokers(all p<0.05).Conclusions This study revealed a J-shaped association between dietary thiamine intake and cognitive decline in cognitively healthy,older Chinese individuals,with an inflection point at 0.68 mg/day and a minimal risk at 0.60-1.00 mg/day of dietary thiamine intake.展开更多
Combining the methods of theoretical,numerical and experimental,this research focuses on the jet formation behavior and optimization of trunconical hypercumulation shaped charge structure.With the three-stage division...Combining the methods of theoretical,numerical and experimental,this research focuses on the jet formation behavior and optimization of trunconical hypercumulation shaped charge structure.With the three-stage division,formation theory of trunconical hypercumulation shaped charge jet is established based on micro element method.By dimensional analysis,main control parameters are identified and their effect on jet formation are analyzed.Through numerical modelling and orthogonal optimization method,influence of the factors and their levels over the indicators of jet tip velocity and jet length as well as order of the significance of each factor and level are obtained.Penetration experiments of trunconical hypercumulation shaped charge based on the orthogonal optimization reveals its advantage over traditional conical shaped charge structure,and finally determines the optimal influence factor level combination.The research and results would provide useful guide for the design and application of trunconical hypercumulation shaped charge structure.展开更多
Penetration characteristic(size and shape of penetration craters made in high hardness ARMSTAL 30PM steel) of shaped charge jets formed after detonations of modified PG-7VM warheads was analyzed in the article. Modifi...Penetration characteristic(size and shape of penetration craters made in high hardness ARMSTAL 30PM steel) of shaped charge jets formed after detonations of modified PG-7VM warheads was analyzed in the article. Modifications consisted in removing the frontal part of the grenade(fuse, ballistic cap and conductive cone) and introducing of the liner cavity filling made of polyacetal copolymer POM-C. The filings in the form of solid cones with three different heights(33%, 66% and 100% of H-the height of original PG-7VM liner) were placed inside of the hollow cone shaped charge liner. As opposed to the vast majority of previously published works(in which warhead optimization studies were focused on increasing of the depth of penetration in rolled homogeneous armor steel) the main aim of the presented modifications was to maximize the damage ratio(diameters of craters, inlet and outlet holes) of target perforated by shaped charge jet at the cost of the loss of part of the jet penetration capability. According to the best knowledge of the authors such approach to the use of the old PG-7VM warheads has not been analyzed so far. Taking into consideration high stock levels of PG-7VM warheads, and the fact that they are continuously being replaced by more efficient and more sophisticated high-explosive anti-tank warheads, it seems reasonable to look for alternate applications of the warheads withdrawn from the service. Thanks to the introduction of proposed modifications the warheads could be used by special forces or other assault units as directional mines or statically detonated cutting shaped charges as well as by combat engineers as universal charges used in various types of engineering or sapper works. The research included experimental penetration tests and their numerical reproduction in the LS-Dyna software with the simulation methodology defined and validated in previous works of the authors.Small differences(average error = 10-20%) were identified between the experimental and numerical results(dimensions of craters made in steel targets were compared) what confirmed the reliability of the modelling methodology and enabled its use for further optimization of the shapes of fillings. Within the analyzed variants of warheads modifications maximum diameters of penetration craters were obtained for the filling of the height of h = 2/3H. The diameters of holes in individual steel plates were increased by 164%, 70%, 65%(for the first, second and third plate, respectively) in relation to the variant without filling. The results of the study indicated that with the use of different materials of fillings and their various heights it is possible to control the shape of penetration craters pierced in the steel targets.展开更多
The effect of the tilt angle on mixed convection and related heat transfer in a“T”shaped double enclosure with four heated obstacles on the bottom surface is numerically investigated.The considered obstacles are con...The effect of the tilt angle on mixed convection and related heat transfer in a“T”shaped double enclosure with four heated obstacles on the bottom surface is numerically investigated.The considered obstacles are constantly kept at a relatively high(fixed)temperature,while the cavity’s upper wall is cooled.The finite volume approach is used to solve the mass,momentum,and energy equations with the SIMPLEC algorithm being exploited to deal with the pressure-velocity coupling.Emphasis is put on the influence of the tilt angle on the solution symmetry,flow structure,and heat exchange through the walls.The following parameters and related ranges are considered:Rayleigh number 104≤Ra≤5.105,tilt angle 0°≤φ≤90°,Reynolds number 100≤Re≤1000,Prandtl number Pr=0.72,block height B=0.5,opening width C=0.15,and distance between blocks D=0.5.The results reveal different branches of solutions on varying Re andφ.They also show that the symmetry of the solution regarding the P_(2)axis is retained for all cases with no tilt and for values of Re between 100 and 1000.展开更多
We propose an eye-shaped keyboard for high-speed text entry in virtual reality (VR), having the shape of dual eyes with characters arranged along the curved eyelids, which ensures low density and short spacing of the ...We propose an eye-shaped keyboard for high-speed text entry in virtual reality (VR), having the shape of dual eyes with characters arranged along the curved eyelids, which ensures low density and short spacing of the keys. The eye-shaped keyboard references the QWERTY key sequence, allowing the users to benefit from their experience using the QWERTY keyboard. The user interacts with an eye-shaped keyboard using rays controlled with both the hands. A character can be entered in one step by moving the rays from the inner eye regions to regions of the characters. A high-speed auto-complete system was designed for the eye-shaped keyboard. We conducted a pilot study to determine the optimal parameters, and a user study to compare our eye-shaped keyboard with the QWERTY and circular keyboards. For beginners, the eye-shaped keyboard performed significantly more efficiently and accurately with less task load and hand movement than the circular keyboard. Compared with the QWERTY keyboard, the eye-shaped keyboard is more accurate and significantly reduces hand translation while maintaining similar efficiency. Finally, to evaluate the potential of eye-shaped keyboards, we conducted another user study. In this study, the participants were asked to type continuously for three days using the proposed eye-shaped keyboard, with two sessions per day. In each session, participants were asked to type for 20min, and then their typing performance was tested. The eye-shaped keyboard was proven to be efficient and promising, with an average speed of 19.89 words per minute (WPM) and mean uncorrected error rate of 1.939%. The maximum speed reached 24.97 WPM after six sessions and continued to increase.展开更多
Fifth generation(5G)wireless networks must meet the needs of emerging technologies like the Internet of Things(IoT),Vehicle-to-everything(V2X),Video on Demand(VoD)services,Device to Device communication(D2D)and many o...Fifth generation(5G)wireless networks must meet the needs of emerging technologies like the Internet of Things(IoT),Vehicle-to-everything(V2X),Video on Demand(VoD)services,Device to Device communication(D2D)and many other bandwidth-hungry multimedia applications that connect a huge number of devices.5G wireless networks demand better bandwidth efficiency,high data rates,low latency,and reduced spectral leakage.To meet these requirements,a suitable 5G waveform must be designed.In this work,a waveform namely Shaped Offset Quadrature Phase Shift Keying based Orthogonal Frequency Division Multiplexing(SOQPSK-OFDM)is proposed for 5G to provide bandwidth efficiency,reduced spectral leakage,and Bit Error Rate(BER).The proposed work is evaluated using a real-time Software Defined Radio(SDR)testbed-Wireless open Access Research Platform(WARP).Experimental and simulation results show that the proposed 5G waveform exhibits better BER performance and reduced Out of Band(OOB)radia-tion when compared with other waveforms like Offset Quadrature Phase Shift Key-ing(OQPSK)and Quadrature Phase Shift Keying(QPSK)based OFDM and a 5G waveform candidate Generalized Frequency Division Multiplexing(GFDM).BER analysis shows that the proposed SOQPSK-OFDM waveform attains a Signal to Noise Ratio(SNR)gain of 7.2 dB at a BER of 10�3,when compared with GFDM in a real-time indoor environment.An SNR gain of 8 and 6 dB is achieved by the proposed work for a BER of 10�4 when compared with QPSK-OFDM and OQPSK-OFDM signals,respectively.A significant reduction in OOB of nearly 15 dB is achieved by the proposed work SOQPSK-OFDM when compared to 16 Quadrature Amplitude Modulation(QAM)mapped OFDM.展开更多
The linear shaped charge cutting technology is an effective technology for aircraft separation.It can separate invalid components from aircrafts timely to achieve light-weight.Magnesium alloy is the lightest metal mat...The linear shaped charge cutting technology is an effective technology for aircraft separation.It can separate invalid components from aircrafts timely to achieve light-weight.Magnesium alloy is the lightest metal material,and can be used to cast effective light-weight components of an aircraft construction.However,the application study of the linear shaped charge cutting technology on magnesium alloy components is basically blank.In response to the demand for the linear separation of magnesium alloys,the Mg-12Gd-0.5Y-0.4Zn alloy is selected to carry out the target shaped charge cutting test.The effects of the shaped charge line density,cutting thickness,and mechanical properties on the cutting performance of the alloy are studied.The shaped charge cutting mechanism is analyzed through the notch structure.The results show that the linear shaped charge cutting performance is significantly affected by the penetration and the collapse.The higher the linear density is,the stronger the ability of the linear shaped charge cutter is,and the greater the penetration depth is,which is advantageous.However,the target structure will be damaged when it is too large(e.g.,4.5 g·m^(-1)).Within 12 mm,when the cutting thickness of the target increases,the penetration depth increases.The lower the tensile strength is,the greater the penetration depth is,and the more conducive the penetration depth to the shaped charge cutting is.When the elongation(EL)increases to 12%,the collapse of the target is incomplete and the target cannot be separated.When the tensile strength of the Mg-Gd-Y-Zn alloy is less than 350 MPa,the EL is less than 6.5%,the cutting thickness is less than 12 mm,and the linear shaped charge cutting of the magnesium alloy can be achieved stably.展开更多
Solidification simulation of manufacturing shaped casting which plays an important role in asSuring the soundness and quality of castings, in minimizing the trial production time and in reducing the manufacturing cost...Solidification simulation of manufacturing shaped casting which plays an important role in asSuring the soundness and quality of castings, in minimizing the trial production time and in reducing the manufacturing cost becomes one of the hottest topics of the new research frontiers of foundry technology at home and abroad. Practical three dimensional computer numerical simulation system for temperature distribution during solidification as well as shrinkage cavity and porosity prediction has already been put into application all over the world. Further fundamental researche5 on fluid flow, thermal stress and micro-modeling as well as practical approaches of numerical simulation of solidification process of shaped castings for routine analysis of foundry industry are still underway.展开更多
With the development of two-stage munitions(a precursor shaped charge(SC)and a following kinetic energy projectile)to attack the hard concrete targets,as well as the increasing applications of ultra-high performance c...With the development of two-stage munitions(a precursor shaped charge(SC)and a following kinetic energy projectile)to attack the hard concrete targets,as well as the increasing applications of ultra-high performance concrete(UHPC)in both civil and military protective structures,a comparative study on the impact performance of SC formed jet on UHPC target is performed experimentally and numerically at present.Firstly,a series of jet penetration/perforation test on the UHPC,45# steel and UHPC/45# steel composite targets are conducted.By assessing the penetration depth and borehole(crater and tunnel)diameter,the influences of target material and configuration as well as the standoff distance of SC on the impact performance of jet are experimentally discussed.Then,by adopting the 2 D multi-material Arbitrary Lagrange-Euler(ALE)algorithm,Fluid-Structure Interaction(FSI)method and erosion algorithm implemented in the finite element code LS-DYNA,the formation and impact performance of jet in the present test are well reproduced.Finally,based on the validated numerical algorithms,constitutive models and the corresponding parameters,the influences of target material(UHPC,NSC and 45# steel),standoff distance,target configuration(stacked and spaced)and weight efficiency on the impact performance of jet are further discussed.The derived conclusions could provide helpful references for evaluating the ballistic performance of jet and designing the protective structures.展开更多
Penetration and internal blast behavior of reactive liner enhanced shaped charge against concrete space were investigated through experiments and simulations.The volume of the enclosed concrete space is about 15 m^(3)...Penetration and internal blast behavior of reactive liner enhanced shaped charge against concrete space were investigated through experiments and simulations.The volume of the enclosed concrete space is about 15 m^(3).The reactive liner enhanced shaped charge utilizes reactive copper double-layered liner,which is composed of an inner copper liner and an outer reactive liner,while the reactive material liner is fabricated by PTFE/Al(Polytetrafluoroethylene/Aluminum)powders through cold-pressing and sintering.Static explosion experiments show that,compared with the shaped charge which utilizes copper liner,the penetration cavity diameter and spalling area of concrete by the novel shaped charge were enlarged to 2 times and 4 times,respectively.Meanwhile,the following reactive material had blast effect and produced significant overpressure inside the concrete closed space.Theoretical analysis indicates concrete strength and detonation pressure of reactive material both affect the penetration cavity diameter.To the blast behavior of reactive material inside the concrete space,developing TNT equivalence model and simulated on AUTODYN-3 D for analysis.Simulation results reproduced propagation process of the shock wave in concrete space,and revealed multi-peaks phenomenon of overpressure-time curves.Furthermore,the empirical relationship between the peak overpressure and relative distance for the shock wave of reactive material was proposed.展开更多
Experiments on shaped charge penetration into high and ultrahigh strength steel-fiber reactive powder concrete(RPC) targets were performed in this paper.Results show that the variation of penetration depth and crater ...Experiments on shaped charge penetration into high and ultrahigh strength steel-fiber reactive powder concrete(RPC) targets were performed in this paper.Results show that the variation of penetration depth and crater diameter with concrete strength is different from that of shaped charge penetration into normal strength concrete(NSC).The crater diameter of RPC is smaller than that of NSC penetrated by the shaped charge.The jet particles are strongly disturbed and hardly reach the crater bottom because they pass through the narrow channel formed by jet penetration into the RPC.The effects of radial drift velocity and gap effects of jet particles for a shaped charge penetration into RFC target are discussed.Moreover,a theoretical model is presented to describe the penetration of shaped charge into RPC target.As the concrete strength increases,the penetration resistance increases and the entrance crater diameter decreases.Given the drift velocity and narrow crater channel,the low-velocity jet particles can hardly reach the crater bottom to increase the penetration depth.Moreover,the narrow channel has a stronger interference to the jet particles with increasing concrete strength;hence,the gap effects must be considered.The drift velocity and gap effects,which are the same as penetration resistance,also have significant effects during the process of shaped charge penetration into ultrahigh-strength concrete,The crater profiles are calculated through a theoretical model,and the results are in good agreement with the experiments.展开更多
Dear Sir, I am Dr Yan-Long Bi, from the Department of Ophthalmology, Tongji University Affiliated to Tongji University School of Medicine, Shanghai, China. I write to present a case report of total limbal stem cells d...Dear Sir, I am Dr Yan-Long Bi, from the Department of Ophthalmology, Tongji University Affiliated to Tongji University School of Medicine, Shanghai, China. I write to present a case report of total limbal stem cells deficiency after treatment with ring-shaped lamellar keratoplasty secondary to Terrien marginal degeneration. During 3展开更多
In this paper, an algorithm for simulating fluid flow and heat transfer for mold filling of shaped castings is presented. The main features of the algorithm include: 1) a simple but practical technique based on VOF me...In this paper, an algorithm for simulating fluid flow and heat transfer for mold filling of shaped castings is presented. The main features of the algorithm include: 1) a simple but practical technique based on VOF method to determine free surface, 2) an explicit scheme of enthalpy to solve the energy equation more efficiently, and 3) an effective treatment to modify the flux deviation due to pressure iteration. In order to verify these methods, well controlled experiments have been repeatedly done with both water analog and gray iron pouring experiments to record the flow patterns and temperature variations. The calculated results are in accordance with the experimental ones. For the applications, the simulated initial temperature distribution right after mold filling was used to analyse subsequent solidification and to predict shrinkage defects.Actual castings were poured and tested in a foundry plant. The reuslts show that the defects predication with considering fluid flow effects is more precise than that without considering the effects.展开更多
Shaped binderless ZSM-11 zeolite catalysts were synthesized via a dry-gel conversion technique from 70ZSM-11/30 SiO_2mix extrudates. 1,6-hexanediamine combined with tetrabutylammonium bromide was proved to be the best...Shaped binderless ZSM-11 zeolite catalysts were synthesized via a dry-gel conversion technique from 70ZSM-11/30 SiO_2mix extrudates. 1,6-hexanediamine combined with tetrabutylammonium bromide was proved to be the best structure directing agent for the synthesis of the binderless ZSM-11 catalyst, without adding other alkaline materials. The 70HZSM-11/30 SiO_2mix serials materials crystallized for different times were detected by X-ray diffraction(XRD), nuclear magnetic resonance(NMR), scanning electron microscopy(SEM), transmission electron microscopy(TEM), scanning transmission electron microscopy–energy dispersive spectroscopy(STEM–EDS) techniques, and so on. In order to investigate the possible crystallization mechanism, the textural and structural properties of 70HZSM-11/30 SiO_2mix serials samples were further characterized by N_2 adsorption–desorption. Acid properties were determined by temperature-programed desorption of NH_3(NH_3-TPD) and pyridine adsorption-infrared(Py-IR) measurements. In the alkylation of benzene with dimethyl ether, the serials catalysts exhibited different benzene conversions. 70HZSM-11/30 SiO_2mix showed the lowest benzene conversion while sample 70HZSM-11/30 SiO_2mix-6.5h synthesized only for 6.5h displayed a higher benzene conversion, even higher than the value over 70HZSM-11/30Al_2O_3mix. Extending the crystallization time, the obtained samples displayed the increased benzene conversion in general under the same reaction conditions. In the end, the relation of physicochemical properties with the reaction performance was investigated.展开更多
Shape memory polymers(SMPs)usually have a one-way shape memory effect.In this paper,an easy-operating method to realize a two-way shape memory effect was demonstrated in a ring-shaped bilayer structure where the two l...Shape memory polymers(SMPs)usually have a one-way shape memory effect.In this paper,an easy-operating method to realize a two-way shape memory effect was demonstrated in a ring-shaped bilayer structure where the two layers are SMPs with different thermal transition temperatures.By designing specific thermomechanical processes,the mismatched deformation between the two layers leads to a morphology change of ring-shaped bilayer structures from a smooth ring to a gear-like buckling shape under cooling and a reversible recovery to the smooth shape under heating.Such a morphology change is ascribed to occurrence and recovery of thermoelastic buckling.This method was validated by finite element simulation.We experimentally investigated the influence of pre-strain on buckling,and it was found that both the buckling occurrence and recovery temperature vary with pre-strain.Furthermore,considering a ring-shaped SMP-SMP bilayer structure,finite element analysis was conducted to study the influence of film thickness and modulus ratio of two layers on buckling behavior.The results showed that the critical buckling wavelength was greatly influenced by film thickness and modulus ratio.W e made a theoretical analysis that accorded well with the numerical results.展开更多
In this paper, the reaction characteristic and its application in shaped charge warhead of a novel reactive material, which introduced copper(Cu) and plumbum(Pb) into traditional polytetrafluoroethylene/aluminum(PTFE/...In this paper, the reaction characteristic and its application in shaped charge warhead of a novel reactive material, which introduced copper(Cu) and plumbum(Pb) into traditional polytetrafluoroethylene/aluminum(PTFE/Al), are studied. The thermal analysis and chemical reaction behavior of the PTFE/Al/Cu/Pb mixture are investigated by Differential Scanning Calorimetry(DSC),Thermo-gravimetry(TG), and Xray Diffraction(XRD) techniques. Then, the shaped charge liners with PTFE/Al/Cu/Pb reactive materials are fabricated, and the X-ray experiments show that they could form reactive jets with excellent performance under the detonation effects of the shaped charge. Based on that, the penetration experiments of shaped charge with PTFE/Al/Cu/Pb reactive liner against steel plates are carried out, and the results demonstrate that the PTFE/Al/Cu/Pb reactive jets could produce a deeper penetration depth compared to the traditional PTFE/Al reactive jets. Meanwhile, the PTFE/Al/Cu/Pb reactive jets also show significant inner-blast effects, leading to dramatically cracking or fragmentation behavior of the penetrated steel plates. This new PTFE/Al/Cu/Pb reactive liner shaped charge presents enhanced penetration behavior for steel targets that incorporates the penetration capability of a high-density and ductility jet, and the chemical energy release of PTFE-matrix reactive materials.展开更多
In order to study the thermal stresses at the mushy zone, a three dimensional rheological model [H]-[H|N]-[N|S]including elastic, visco-elastic and visco-plastic elements was established, its al gorithm and codes for ...In order to study the thermal stresses at the mushy zone, a three dimensional rheological model [H]-[H|N]-[N|S]including elastic, visco-elastic and visco-plastic elements was established, its al gorithm and codes for finite element method were also developed. A FDM/FEM integrated analysis system of thermal stresses was built based on the integration of this procedure with thermal analysis by finite difference method. A steel sample casting with a hot spot was simu lated in order to validate this system, and the calculated and experimental results were in good展开更多
The bore-center annular shaped charge(BCASC)is a new type of shaped charge which can generate a larger-diameter hole in steel targets than classical shaped charges.In this paper,the influence of three liner materials,...The bore-center annular shaped charge(BCASC)is a new type of shaped charge which can generate a larger-diameter hole in steel targets than classical shaped charges.In this paper,the influence of three liner materials,i.e.molybdenum,nickel and copper,on BCASC formation and penetrating into steel targets was investigated by experiment and numerical simulation.The simulation results were well consistent with the experimental results.This study showed that,at 0.50D standoff distance,the axial velocity of the molybdenum projectile was lower than that of the nickel and copper projectiles.The nickel and copper projectiles had almost the same head velocity.The absolute values of the radial velocity of the molybdenum projectile head was lower than that of the nickel and copper projectiles.However,at 0.75D standoff distance,the absolute values of the radial velocity of the molybdenum projectile head became much greater than that of the nickel and copper projectile heads.The projectile formed by BCASC with the molybdenum liner had the highest penetration depth of 61.5 mm,which was 10.0%and 21.3%higher than that generated by the copper and nickel projectiles.展开更多
基金funded by the Swedish Armed Forces under Contract No AT.9220620。
文摘Reactive armour is a very efficient add-on armour against shaped charge threats.Explosive reactive armour consists of one or several plates that are accelerated by an explosive.Similar but less violent acceleration of plates can also be achieved in a completely inert reactive armour.To be efficient against elongated jets,the motion of the plates needs to be inclined against the jet such that a sliding contact between the jet and the plates is established.This sliding contact causes a deflection and thinning of the jet.Under certain circumstances,the contact will become unstable,leading to severe disturbances on the jet.These disturbances will drastically reduce the jet penetration performance and it is therefore of interest to study the conditions that leads to an unstable contact.Previous studies on the interaction between shaped charge jets and flyer plates have shown that it is mainly the forward moving plate in an explosive reactive armour that is effective in disturbing the jet.This is usually attributed to the higher plate-to-jet mass flux ratio involved in the collision of the forward moving plate compared to the backward moving plate.For slow moving plates,as occurs in inert reactive armour,the difference in mass flux for the forward and backward moving plate is much lesser,and it is therefore of interest to study if other factors than the mass flux influences on the protection capability.In this work,experiments have been performed where a plate is accelerated along its length,interacting with a shaped charge jet that is fired at an oblique angle to the plate’s normal,either against or along the plate’s velocity.The arrangement corresponds to a jet interacting with a flyer plate from a reactive armour,with the exception that the collision velocity is the same for both types of obliquities in these experiments.The experiments show that disturbances on the jet are different in the two cases even though the collision velocities are the same.Numerical simulations of the interaction support the observation.The difference is attributed to the character of the contact pressure in the interaction region.For a backward moving plate,the maximum contact pressure is obtained at the beginning of the interaction zone and the contact pressure is therefore higher upstream than downstream of the jet while the opposite is true for a forward moving plate.A negative interface pressure gradient with respect to the jet motion results in a more stable flow than a positive,which means that the jet-plate contact is more stable for a backward moving plate than for a forward moving plate.A forward moving plate is thus more effective in disturbing the jet than a backward moving plate,not only because of the higher jet to plate mass flux ratio but also because of the character of the contact with the jet.
基金National Key Research and Development Program of China(2022YFC2009600,2022YFC2009605)National Natural Science Foundation of China(81973133)。
文摘Background The prospective association of dietary thiamine intake with the risk of cognitive decline among the general older adults remains uncertain.Aims To investigate the association between dietary thiamine intake and cognitive decline in cognitively healthy,older Chinese individuals.Methods The study included a total of 3106 participants capable of completing repeated cognitive function tests.Dietary nutrient intake information was collected through 3-day dietary recalls and using a 3-day food-weighed method to assess cooking oil and condiment consumption.Cognitive decline was defined as the 5-year decline rate in global or composite cognitive scores based on a subset of items from the Telephone Interview for Cognitive Status-modified.Results The median follow-up duration was 5.9 years.There was a J-shaped relationship between dietary thiamine intake and the 5-year decline rate in global and composite cognitive scores,with an inflection point of 0.68 mg/day(95%confidence interval(Cl):0.56 to 0.80)and a minimal risk at 0.60-1.00 mg/day of dietary thiamine intake.Before the inflection point,thiamine intake was not significantly associated with cognitive decline.Beyond the inflection point,each unit increase in thiamine intake(mg/day)was associated with a significant decrease of 4.24(95%Cl:2.22 to 6.27)points in the global score and 0.49(95%Cl:0.23 to 0.76)standard units in the composite score within 5 years.A stronger positive association between thiamine intake and cognitive decline was observed in those with hypertension,obesity and those who were non-smokers(all p<0.05).Conclusions This study revealed a J-shaped association between dietary thiamine intake and cognitive decline in cognitively healthy,older Chinese individuals,with an inflection point at 0.68 mg/day and a minimal risk at 0.60-1.00 mg/day of dietary thiamine intake.
基金support from the Beijing Municipal Natural Science Foundation(Grant No.1214022).
文摘Combining the methods of theoretical,numerical and experimental,this research focuses on the jet formation behavior and optimization of trunconical hypercumulation shaped charge structure.With the three-stage division,formation theory of trunconical hypercumulation shaped charge jet is established based on micro element method.By dimensional analysis,main control parameters are identified and their effect on jet formation are analyzed.Through numerical modelling and orthogonal optimization method,influence of the factors and their levels over the indicators of jet tip velocity and jet length as well as order of the significance of each factor and level are obtained.Penetration experiments of trunconical hypercumulation shaped charge based on the orthogonal optimization reveals its advantage over traditional conical shaped charge structure,and finally determines the optimal influence factor level combination.The research and results would provide useful guide for the design and application of trunconical hypercumulation shaped charge structure.
文摘Penetration characteristic(size and shape of penetration craters made in high hardness ARMSTAL 30PM steel) of shaped charge jets formed after detonations of modified PG-7VM warheads was analyzed in the article. Modifications consisted in removing the frontal part of the grenade(fuse, ballistic cap and conductive cone) and introducing of the liner cavity filling made of polyacetal copolymer POM-C. The filings in the form of solid cones with three different heights(33%, 66% and 100% of H-the height of original PG-7VM liner) were placed inside of the hollow cone shaped charge liner. As opposed to the vast majority of previously published works(in which warhead optimization studies were focused on increasing of the depth of penetration in rolled homogeneous armor steel) the main aim of the presented modifications was to maximize the damage ratio(diameters of craters, inlet and outlet holes) of target perforated by shaped charge jet at the cost of the loss of part of the jet penetration capability. According to the best knowledge of the authors such approach to the use of the old PG-7VM warheads has not been analyzed so far. Taking into consideration high stock levels of PG-7VM warheads, and the fact that they are continuously being replaced by more efficient and more sophisticated high-explosive anti-tank warheads, it seems reasonable to look for alternate applications of the warheads withdrawn from the service. Thanks to the introduction of proposed modifications the warheads could be used by special forces or other assault units as directional mines or statically detonated cutting shaped charges as well as by combat engineers as universal charges used in various types of engineering or sapper works. The research included experimental penetration tests and their numerical reproduction in the LS-Dyna software with the simulation methodology defined and validated in previous works of the authors.Small differences(average error = 10-20%) were identified between the experimental and numerical results(dimensions of craters made in steel targets were compared) what confirmed the reliability of the modelling methodology and enabled its use for further optimization of the shapes of fillings. Within the analyzed variants of warheads modifications maximum diameters of penetration craters were obtained for the filling of the height of h = 2/3H. The diameters of holes in individual steel plates were increased by 164%, 70%, 65%(for the first, second and third plate, respectively) in relation to the variant without filling. The results of the study indicated that with the use of different materials of fillings and their various heights it is possible to control the shape of penetration craters pierced in the steel targets.
文摘The effect of the tilt angle on mixed convection and related heat transfer in a“T”shaped double enclosure with four heated obstacles on the bottom surface is numerically investigated.The considered obstacles are constantly kept at a relatively high(fixed)temperature,while the cavity’s upper wall is cooled.The finite volume approach is used to solve the mass,momentum,and energy equations with the SIMPLEC algorithm being exploited to deal with the pressure-velocity coupling.Emphasis is put on the influence of the tilt angle on the solution symmetry,flow structure,and heat exchange through the walls.The following parameters and related ranges are considered:Rayleigh number 104≤Ra≤5.105,tilt angle 0°≤φ≤90°,Reynolds number 100≤Re≤1000,Prandtl number Pr=0.72,block height B=0.5,opening width C=0.15,and distance between blocks D=0.5.The results reveal different branches of solutions on varying Re andφ.They also show that the symmetry of the solution regarding the P_(2)axis is retained for all cases with no tilt and for values of Re between 100 and 1000.
文摘We propose an eye-shaped keyboard for high-speed text entry in virtual reality (VR), having the shape of dual eyes with characters arranged along the curved eyelids, which ensures low density and short spacing of the keys. The eye-shaped keyboard references the QWERTY key sequence, allowing the users to benefit from their experience using the QWERTY keyboard. The user interacts with an eye-shaped keyboard using rays controlled with both the hands. A character can be entered in one step by moving the rays from the inner eye regions to regions of the characters. A high-speed auto-complete system was designed for the eye-shaped keyboard. We conducted a pilot study to determine the optimal parameters, and a user study to compare our eye-shaped keyboard with the QWERTY and circular keyboards. For beginners, the eye-shaped keyboard performed significantly more efficiently and accurately with less task load and hand movement than the circular keyboard. Compared with the QWERTY keyboard, the eye-shaped keyboard is more accurate and significantly reduces hand translation while maintaining similar efficiency. Finally, to evaluate the potential of eye-shaped keyboards, we conducted another user study. In this study, the participants were asked to type continuously for three days using the proposed eye-shaped keyboard, with two sessions per day. In each session, participants were asked to type for 20min, and then their typing performance was tested. The eye-shaped keyboard was proven to be efficient and promising, with an average speed of 19.89 words per minute (WPM) and mean uncorrected error rate of 1.939%. The maximum speed reached 24.97 WPM after six sessions and continued to increase.
文摘Fifth generation(5G)wireless networks must meet the needs of emerging technologies like the Internet of Things(IoT),Vehicle-to-everything(V2X),Video on Demand(VoD)services,Device to Device communication(D2D)and many other bandwidth-hungry multimedia applications that connect a huge number of devices.5G wireless networks demand better bandwidth efficiency,high data rates,low latency,and reduced spectral leakage.To meet these requirements,a suitable 5G waveform must be designed.In this work,a waveform namely Shaped Offset Quadrature Phase Shift Keying based Orthogonal Frequency Division Multiplexing(SOQPSK-OFDM)is proposed for 5G to provide bandwidth efficiency,reduced spectral leakage,and Bit Error Rate(BER).The proposed work is evaluated using a real-time Software Defined Radio(SDR)testbed-Wireless open Access Research Platform(WARP).Experimental and simulation results show that the proposed 5G waveform exhibits better BER performance and reduced Out of Band(OOB)radia-tion when compared with other waveforms like Offset Quadrature Phase Shift Key-ing(OQPSK)and Quadrature Phase Shift Keying(QPSK)based OFDM and a 5G waveform candidate Generalized Frequency Division Multiplexing(GFDM).BER analysis shows that the proposed SOQPSK-OFDM waveform attains a Signal to Noise Ratio(SNR)gain of 7.2 dB at a BER of 10�3,when compared with GFDM in a real-time indoor environment.An SNR gain of 8 and 6 dB is achieved by the proposed work for a BER of 10�4 when compared with QPSK-OFDM and OQPSK-OFDM signals,respectively.A significant reduction in OOB of nearly 15 dB is achieved by the proposed work SOQPSK-OFDM when compared to 16 Quadrature Amplitude Modulation(QAM)mapped OFDM.
基金the National Natural Science Foundation of China(No.U2037601)。
文摘The linear shaped charge cutting technology is an effective technology for aircraft separation.It can separate invalid components from aircrafts timely to achieve light-weight.Magnesium alloy is the lightest metal material,and can be used to cast effective light-weight components of an aircraft construction.However,the application study of the linear shaped charge cutting technology on magnesium alloy components is basically blank.In response to the demand for the linear separation of magnesium alloys,the Mg-12Gd-0.5Y-0.4Zn alloy is selected to carry out the target shaped charge cutting test.The effects of the shaped charge line density,cutting thickness,and mechanical properties on the cutting performance of the alloy are studied.The shaped charge cutting mechanism is analyzed through the notch structure.The results show that the linear shaped charge cutting performance is significantly affected by the penetration and the collapse.The higher the linear density is,the stronger the ability of the linear shaped charge cutter is,and the greater the penetration depth is,which is advantageous.However,the target structure will be damaged when it is too large(e.g.,4.5 g·m^(-1)).Within 12 mm,when the cutting thickness of the target increases,the penetration depth increases.The lower the tensile strength is,the greater the penetration depth is,and the more conducive the penetration depth to the shaped charge cutting is.When the elongation(EL)increases to 12%,the collapse of the target is incomplete and the target cannot be separated.When the tensile strength of the Mg-Gd-Y-Zn alloy is less than 350 MPa,the EL is less than 6.5%,the cutting thickness is less than 12 mm,and the linear shaped charge cutting of the magnesium alloy can be achieved stably.
文摘Solidification simulation of manufacturing shaped casting which plays an important role in asSuring the soundness and quality of castings, in minimizing the trial production time and in reducing the manufacturing cost becomes one of the hottest topics of the new research frontiers of foundry technology at home and abroad. Practical three dimensional computer numerical simulation system for temperature distribution during solidification as well as shrinkage cavity and porosity prediction has already been put into application all over the world. Further fundamental researche5 on fluid flow, thermal stress and micro-modeling as well as practical approaches of numerical simulation of solidification process of shaped castings for routine analysis of foundry industry are still underway.
基金supported by the National Natural Science Foundation of China (51438003,51878507)
文摘With the development of two-stage munitions(a precursor shaped charge(SC)and a following kinetic energy projectile)to attack the hard concrete targets,as well as the increasing applications of ultra-high performance concrete(UHPC)in both civil and military protective structures,a comparative study on the impact performance of SC formed jet on UHPC target is performed experimentally and numerically at present.Firstly,a series of jet penetration/perforation test on the UHPC,45# steel and UHPC/45# steel composite targets are conducted.By assessing the penetration depth and borehole(crater and tunnel)diameter,the influences of target material and configuration as well as the standoff distance of SC on the impact performance of jet are experimentally discussed.Then,by adopting the 2 D multi-material Arbitrary Lagrange-Euler(ALE)algorithm,Fluid-Structure Interaction(FSI)method and erosion algorithm implemented in the finite element code LS-DYNA,the formation and impact performance of jet in the present test are well reproduced.Finally,based on the validated numerical algorithms,constitutive models and the corresponding parameters,the influences of target material(UHPC,NSC and 45# steel),standoff distance,target configuration(stacked and spaced)and weight efficiency on the impact performance of jet are further discussed.The derived conclusions could provide helpful references for evaluating the ballistic performance of jet and designing the protective structures.
基金supported by National Natural Science Foundation of china[grant number:U1730112]。
文摘Penetration and internal blast behavior of reactive liner enhanced shaped charge against concrete space were investigated through experiments and simulations.The volume of the enclosed concrete space is about 15 m^(3).The reactive liner enhanced shaped charge utilizes reactive copper double-layered liner,which is composed of an inner copper liner and an outer reactive liner,while the reactive material liner is fabricated by PTFE/Al(Polytetrafluoroethylene/Aluminum)powders through cold-pressing and sintering.Static explosion experiments show that,compared with the shaped charge which utilizes copper liner,the penetration cavity diameter and spalling area of concrete by the novel shaped charge were enlarged to 2 times and 4 times,respectively.Meanwhile,the following reactive material had blast effect and produced significant overpressure inside the concrete closed space.Theoretical analysis indicates concrete strength and detonation pressure of reactive material both affect the penetration cavity diameter.To the blast behavior of reactive material inside the concrete space,developing TNT equivalence model and simulated on AUTODYN-3 D for analysis.Simulation results reproduced propagation process of the shock wave in concrete space,and revealed multi-peaks phenomenon of overpressure-time curves.Furthermore,the empirical relationship between the peak overpressure and relative distance for the shock wave of reactive material was proposed.
基金supported by the Natural Science Foundation of China through Grant No.11702144。
文摘Experiments on shaped charge penetration into high and ultrahigh strength steel-fiber reactive powder concrete(RPC) targets were performed in this paper.Results show that the variation of penetration depth and crater diameter with concrete strength is different from that of shaped charge penetration into normal strength concrete(NSC).The crater diameter of RPC is smaller than that of NSC penetrated by the shaped charge.The jet particles are strongly disturbed and hardly reach the crater bottom because they pass through the narrow channel formed by jet penetration into the RPC.The effects of radial drift velocity and gap effects of jet particles for a shaped charge penetration into RFC target are discussed.Moreover,a theoretical model is presented to describe the penetration of shaped charge into RPC target.As the concrete strength increases,the penetration resistance increases and the entrance crater diameter decreases.Given the drift velocity and narrow crater channel,the low-velocity jet particles can hardly reach the crater bottom to increase the penetration depth.Moreover,the narrow channel has a stronger interference to the jet particles with increasing concrete strength;hence,the gap effects must be considered.The drift velocity and gap effects,which are the same as penetration resistance,also have significant effects during the process of shaped charge penetration into ultrahigh-strength concrete,The crater profiles are calculated through a theoretical model,and the results are in good agreement with the experiments.
基金National Natural Science Foundation of China (No. 30973247)Shanghai Excellent University Teacher Foundation, China (No. 1500144019)
文摘Dear Sir, I am Dr Yan-Long Bi, from the Department of Ophthalmology, Tongji University Affiliated to Tongji University School of Medicine, Shanghai, China. I write to present a case report of total limbal stem cells deficiency after treatment with ring-shaped lamellar keratoplasty secondary to Terrien marginal degeneration. During 3
文摘In this paper, an algorithm for simulating fluid flow and heat transfer for mold filling of shaped castings is presented. The main features of the algorithm include: 1) a simple but practical technique based on VOF method to determine free surface, 2) an explicit scheme of enthalpy to solve the energy equation more efficiently, and 3) an effective treatment to modify the flux deviation due to pressure iteration. In order to verify these methods, well controlled experiments have been repeatedly done with both water analog and gray iron pouring experiments to record the flow patterns and temperature variations. The calculated results are in accordance with the experimental ones. For the applications, the simulated initial temperature distribution right after mold filling was used to analyse subsequent solidification and to predict shrinkage defects.Actual castings were poured and tested in a foundry plant. The reuslts show that the defects predication with considering fluid flow effects is more precise than that without considering the effects.
基金supported by K.C.Wong Education FoundationDalian Eminent Young Scientist Program(2015R009)Natural Science Foundation of Heilongjiang Province(No.B2015006)
文摘Shaped binderless ZSM-11 zeolite catalysts were synthesized via a dry-gel conversion technique from 70ZSM-11/30 SiO_2mix extrudates. 1,6-hexanediamine combined with tetrabutylammonium bromide was proved to be the best structure directing agent for the synthesis of the binderless ZSM-11 catalyst, without adding other alkaline materials. The 70HZSM-11/30 SiO_2mix serials materials crystallized for different times were detected by X-ray diffraction(XRD), nuclear magnetic resonance(NMR), scanning electron microscopy(SEM), transmission electron microscopy(TEM), scanning transmission electron microscopy–energy dispersive spectroscopy(STEM–EDS) techniques, and so on. In order to investigate the possible crystallization mechanism, the textural and structural properties of 70HZSM-11/30 SiO_2mix serials samples were further characterized by N_2 adsorption–desorption. Acid properties were determined by temperature-programed desorption of NH_3(NH_3-TPD) and pyridine adsorption-infrared(Py-IR) measurements. In the alkylation of benzene with dimethyl ether, the serials catalysts exhibited different benzene conversions. 70HZSM-11/30 SiO_2mix showed the lowest benzene conversion while sample 70HZSM-11/30 SiO_2mix-6.5h synthesized only for 6.5h displayed a higher benzene conversion, even higher than the value over 70HZSM-11/30Al_2O_3mix. Extending the crystallization time, the obtained samples displayed the increased benzene conversion in general under the same reaction conditions. In the end, the relation of physicochemical properties with the reaction performance was investigated.
基金This work was supported by the National Natural Science Foundations of China(Grant 11272044)the Fundamental Research Funds for the Central Universities(Grant 2018JBM305).
文摘Shape memory polymers(SMPs)usually have a one-way shape memory effect.In this paper,an easy-operating method to realize a two-way shape memory effect was demonstrated in a ring-shaped bilayer structure where the two layers are SMPs with different thermal transition temperatures.By designing specific thermomechanical processes,the mismatched deformation between the two layers leads to a morphology change of ring-shaped bilayer structures from a smooth ring to a gear-like buckling shape under cooling and a reversible recovery to the smooth shape under heating.Such a morphology change is ascribed to occurrence and recovery of thermoelastic buckling.This method was validated by finite element simulation.We experimentally investigated the influence of pre-strain on buckling,and it was found that both the buckling occurrence and recovery temperature vary with pre-strain.Furthermore,considering a ring-shaped SMP-SMP bilayer structure,finite element analysis was conducted to study the influence of film thickness and modulus ratio of two layers on buckling behavior.The results showed that the critical buckling wavelength was greatly influenced by film thickness and modulus ratio.W e made a theoretical analysis that accorded well with the numerical results.
基金funded under the National Natural Science Foundation of China (No. 12002046)the study was also supported by the State Key Laboratory of Explosion Science and Technology of China。
文摘In this paper, the reaction characteristic and its application in shaped charge warhead of a novel reactive material, which introduced copper(Cu) and plumbum(Pb) into traditional polytetrafluoroethylene/aluminum(PTFE/Al), are studied. The thermal analysis and chemical reaction behavior of the PTFE/Al/Cu/Pb mixture are investigated by Differential Scanning Calorimetry(DSC),Thermo-gravimetry(TG), and Xray Diffraction(XRD) techniques. Then, the shaped charge liners with PTFE/Al/Cu/Pb reactive materials are fabricated, and the X-ray experiments show that they could form reactive jets with excellent performance under the detonation effects of the shaped charge. Based on that, the penetration experiments of shaped charge with PTFE/Al/Cu/Pb reactive liner against steel plates are carried out, and the results demonstrate that the PTFE/Al/Cu/Pb reactive jets could produce a deeper penetration depth compared to the traditional PTFE/Al reactive jets. Meanwhile, the PTFE/Al/Cu/Pb reactive jets also show significant inner-blast effects, leading to dramatically cracking or fragmentation behavior of the penetrated steel plates. This new PTFE/Al/Cu/Pb reactive liner shaped charge presents enhanced penetration behavior for steel targets that incorporates the penetration capability of a high-density and ductility jet, and the chemical energy release of PTFE-matrix reactive materials.
文摘In order to study the thermal stresses at the mushy zone, a three dimensional rheological model [H]-[H|N]-[N|S]including elastic, visco-elastic and visco-plastic elements was established, its al gorithm and codes for finite element method were also developed. A FDM/FEM integrated analysis system of thermal stresses was built based on the integration of this procedure with thermal analysis by finite difference method. A steel sample casting with a hot spot was simu lated in order to validate this system, and the calculated and experimental results were in good
基金supported by the National Natural Science Foundation of China(No.11732003)Beijing Natural Science Foundation(No.8182050)+1 种基金Science Challenge Project(No.TZ2016001)National Key R&D Program of China(No.2017YFC0804700)
文摘The bore-center annular shaped charge(BCASC)is a new type of shaped charge which can generate a larger-diameter hole in steel targets than classical shaped charges.In this paper,the influence of three liner materials,i.e.molybdenum,nickel and copper,on BCASC formation and penetrating into steel targets was investigated by experiment and numerical simulation.The simulation results were well consistent with the experimental results.This study showed that,at 0.50D standoff distance,the axial velocity of the molybdenum projectile was lower than that of the nickel and copper projectiles.The nickel and copper projectiles had almost the same head velocity.The absolute values of the radial velocity of the molybdenum projectile head was lower than that of the nickel and copper projectiles.However,at 0.75D standoff distance,the absolute values of the radial velocity of the molybdenum projectile head became much greater than that of the nickel and copper projectile heads.The projectile formed by BCASC with the molybdenum liner had the highest penetration depth of 61.5 mm,which was 10.0%and 21.3%higher than that generated by the copper and nickel projectiles.
