The monocrystalline silicon is a promising material that could be used in solar cells that convert light into electricity. Although the cost of ordinary silicon (Si) solar cells has decreased significantly over the pa...The monocrystalline silicon is a promising material that could be used in solar cells that convert light into electricity. Although the cost of ordinary silicon (Si) solar cells has decreased significantly over the past two decades, the conversion efficiency of these cells has remained relatively high. While solar cells have a great potential as a device of renewable energy, the high cost they incur per Watt continues to be a significant barrier to their widespread implementation. As a consequence, it is vital to conduct research into alternate materials that may be used in the construction of solar cells. The heterojunction solar cell (HJSC), which is based on n-type zinc oxide (n-ZnO) and p-type silicon (p-Si), is one of the numerous alternatives of the typical Si single homojunction solar cell. There are many deficiencies that can be found in the published research on n-ZnO/p-Si heterojunction solar cell. Inconsistencies in the stated value of open circuit voltage (V<sub>oc</sub>) of the solar cell are one example of deficiency. The absence of a full theoretical study to evaluate the potential of the solar cell structure is another deficiency that can be found in these researches. A lower value of experimentally obtained V<sub>OC</sub> in comparison to the theoretical prediction based on the band-gap between n-ZnO and p-Si. There needs to be more consensus among scientists regarding the optimal conditions for the growth of zinc oxide. Many software’s are available for simulating and optimizing the solar cells based on these parameters. For this purpose, in this dissertation, I provide computational results relevant to n-ZnO/p-Si HJSC to overcome deficiencies that have been identified. While modeling and simulating the potential of the solar cell structure with AFORS-HET, it is essential to consider the constraints that exist in the real world. AFORS-HET was explicitly designed to mimic the multilayer solar cell arrangement. In AFORS-HET, we can add up to seven layers for solar cell layout. By using this software, we can figure out the open circuit voltage (V<sub>OC</sub>), the short circuit current (J<sub>SC</sub>), the quantum efficiency (QE, %), the heterojunction energy band structure, and the power conversion efficiency (PCE).展开更多
AIM:To evaluate the efficacy and safety of silicone oil(SO)as a corneal lubricant to improve visualization during vitrectomy.METHODS:Patients who underwent vitreoretinal surgery were divided into two groups.Group 1 wa...AIM:To evaluate the efficacy and safety of silicone oil(SO)as a corneal lubricant to improve visualization during vitrectomy.METHODS:Patients who underwent vitreoretinal surgery were divided into two groups.Group 1 was operated on with initial SO(Oxane 5700)as a corneal lubricant.Group 2 was operated on with initial lactated ringer’s solution(LRS)and then replaced with SO as required.Fundus clarity was scored during the surgery.Fluorescein staining was performed to determine the damage to corneal epithelium.RESULTS:Totally 114 eyes of 114 patients were included.Single SO use maintained a clear cornea and provided excellent visualization of surgical image.In group 1,the fundus clarity was grade 3 in 41/45 eyes and grade 2 in 4/45 eyes.In group 2,corneal edema frequently occurred after initial LRS use.The fundus clarity was grade 3 in 19/69 eyes,2 in 37/69 eyes and 1 in 13/69 eyes(P<0.05).SO was applied in 29 eyes of initial LRS use with subsequent corneal edema,which eliminated the corneal edema in 26 eyes.Corneal fluorescein staining score in group 1 was 0 in 28 eyes,1 in 11 eyes and 2 in 6 eyes,and 40,20 and 9,respectively,in group 2(all P>0.05).CONCLUSION:The use of SO as a corneal lubricant is effective and safe for preserving and improving corneal clarity and providing clear surgical field during vitrectomy.展开更多
Fragrant rice has a high market value,and it is a popular rice type among consumers owing to its pleasant flavor.Plantation methods,nitrogen(N)fertilizers,and silicon(Si)fertilizers can affect the grain yield and frag...Fragrant rice has a high market value,and it is a popular rice type among consumers owing to its pleasant flavor.Plantation methods,nitrogen(N)fertilizers,and silicon(Si)fertilizers can affect the grain yield and fragrance of fragrant rice.However,the core commercial rice production attributes,namely the head rice yield(HRY)and 2-acetyl-1-pyrroline(2-AP)content of fragrant rice,under various nitrogen and silicon(N-Si)fertilization levels and different plantation methods remain unknown.The field experiment in this study was performed in the early seasons of 2018 and 2019 with two popular indica fragrant rice cultivars(Yuxiangyouzhan and Xiangyaxiangzhan).They were grown under six N-Si fertilization treatments(combinations of two levels of Si fertilizer,0 kg Si ha^(−1)(Si0)and 150 kg Si ha^(−1)(Si1),and three levels of N fertilizer,0 kg N ha^(−1)(N0),150 kg N ha^(−1)(N1),and 220 kg N ha^(−1)(N2))and three plantation methods(artificial transplanting(AT),mechanical transplanting(MT),and mechanical direct-seeding(MD)).The results showed that the N-Si fertilization treatments and all the plantation methods significantly affected the HRY and 2-AP content and related parameters of the two different fragrant rice cultivars.Compared with the Si0N0 treatment,the N-Si fertilization treatments resulted in higher HRY and 2-AP contents.The rates of brown rice,milled rice,head rice,and chalky rice of the fragrant rice also improved with the N-Si fertilization treatments.The N-Si fertilization treatments increased the activities of N metabolism enzymes and the accumulation of N and Si in various parts of the fragrant rice,and affected their antioxidant response parameters.The key parameters for the HRY and 2-AP content were assessed by redundancy analysis.Furthermore,the structural equation model revealed that the Si and N accumulation levels indirectly affected the HRY by affecting the N metabolism enzyme activity,N use efficiency,and grain quality of fragrant rice.Moreover,high N and Si accumulation directly promoted the 2-AP content or affected the antioxidant response parameters and indirectly regulated 2-AP synthesis.The interactions of the MT method with the N-Si fertilization treatments varied in the fragrant rice cultivars in terms of the HRY and 2-AP content,whereas the MD method was beneficial to the 2-AP content in both fragrant rice cultivars under the N-Si fertilization treatments.展开更多
Aluminum (Al) toxicity is a considerable factor limiting crop yield and biomass in acidic soil. Tartary buckwheatgrowing in acidic soil may suffer from Al poisoning. Here, we investigated the influence of Al stress on...Aluminum (Al) toxicity is a considerable factor limiting crop yield and biomass in acidic soil. Tartary buckwheatgrowing in acidic soil may suffer from Al poisoning. Here, we investigated the influence of Al stress on the growthof tartary buckwheat seedling roots, and the alleviation of Al stress by silicon (Si), as has been demonstrated inmany crops. Under Al stress, root growth (total root length, primary root length, root tips, root surface area, androot volume) was significantly inhibited, and Al and malondialdehyde (MDA) accumulated in the root tips. At thesame time, catalase (CAT) and ascorbate peroxidase activities, polyphenols, flavonoids, and 1,1-diphenyl-2-picrylhydrazyl(DPPH) and 2,2′-azinobis-(3-ethylbenzthiazoline-6-sulphonate) (ABTS) free-radical scavenging abilitywere significantly decreased. After the application of Si, root growth, Al accumulation, and oxidative damage wereimproved. Compared to Al-treated seedlings, the contents of ·O2− and MDA decreased by 29.39% and 25.22%,respectively. This was associated with Si-induced increases in peroxidase and CAT enzyme activity, flavonoidcompounds, and free-radical scavenging (DPPH and ABTS). The application of Si therefore has positive effectson Al toxicity in tartary buckwheat roots by reducing Al accumulation in the roots and maintaining oxidationhomeostasis.展开更多
[Objectives]This study was conducted to investigate the scientific application of silicon fertilizer in rice cultivation,one of the staple crops.[Methods]In 2022,Yandu District carried out a special experiment and fie...[Objectives]This study was conducted to investigate the scientific application of silicon fertilizer in rice cultivation,one of the staple crops.[Methods]In 2022,Yandu District carried out a special experiment and field demonstration study on the effects of foliar application of Zhengda water-soluble silicon fertilizer on rice production.[Results]The preliminary results showed that①Zhengda water-soluble silicon fertilizer could effectively improve the growth and development of rice and improve the population quality.The peak number of tillers,productive tiller percentage,number of effective panicles and number of effective grains per panicle increased by 6.7%,5.8%,5.5%,and 1.2%,respectively.②The yield and processing quality were improved.After applying silicon fertilizer,the yield per unit area increased by about 6.8%,and the unpolished rice yield,milled rice yield and head rice yield increased by 0.7%,1.94%and 2.15%respectively.[Conclusions]The demonstration application of silicon fertilizer in field cultivation of rice in Yandu District further proves previous research conclusions and has important practical significance.展开更多
BACKGROUND Endophthalmitis occurring in silicone oil-filled eyes is a very rare occurrence,with reported incidence rates ranging between 0.07%and 0.039%.Traditional methods of management of infectious endophthalmitis ...BACKGROUND Endophthalmitis occurring in silicone oil-filled eyes is a very rare occurrence,with reported incidence rates ranging between 0.07%and 0.039%.Traditional methods of management of infectious endophthalmitis include the removal of silicone oil,washout of the vitreous cavity,administration of intravitreal antibiotics,and reinjection of silicone oil.CASE SUMMARY Herein,we report the case of a 39-year-old man with unilateral endophthalmitis after pars plana vitrectomy and silicone oil tamponade.Intravitreal injections of full-dose antibiotics and anterior chamber washout were used to treat the patient.No signs of retinal toxicity were observed during the follow-up period.CONCLUSION Intravitreal full-dose antibiotic injections and anterior chamber washout are promising alternatives to traditional therapies for endophthalmitis in silicone oilfilled eyes.展开更多
An experimental investigation into the thermal conductivity of CF-SiC two-phase composite asphalt concrete is presented.The main objective of this study was to verify the possibility of using SiC powder instead of min...An experimental investigation into the thermal conductivity of CF-SiC two-phase composite asphalt concrete is presented.The main objective of this study was to verify the possibility of using SiC powder instead of mineral powder as the thermal conductive filler to prepare a new type of asphalt concrete and improve the efficiency of electrothermal snow and ice melting systems accordingly.The thermal conductivity of asphalt concrete prepared with different thermally conductive fillers was tested by a transient plane source method,and the related performances were measured.Then the temperature rise rate and surface temperature were studied through field heating tests.Finally,the actual ice melting efficiency of the thermally conductive asphalt concrete was evaluated using an effective electrothermal system.As shown by the experimental results,the composite made of SiC powder and carbon fiber has a high thermal conductivity.When SiC replaces mineral powder,the thermal conductivity of the asphalt mixture increases first and then decreases with the increase of carbon fiber content.In the present study,in particular,the thermal conductivity attained a peak when the carbon fiber content was 0.2%of the aggregate mass.展开更多
Femtosecond laser-induced periodic surface structures(LIPSS)have been extensively studied over the past few decades.In particular,the period and groove width of high-spatial-frequency LIPSS(HSFL)is much smaller than t...Femtosecond laser-induced periodic surface structures(LIPSS)have been extensively studied over the past few decades.In particular,the period and groove width of high-spatial-frequency LIPSS(HSFL)is much smaller than the diffraction limit,making it a useful method for efficient nanomanufacturing.However,compared with the low-spatial-frequency LIPSS(LSFL),the structure size of the HSFL is smaller,and it is more easily submerged.Therefore,the formation mechanism of HSFL is complex and has always been a research hotspot in this field.In this study,regular LSFL with a period of 760 nm was fabricated in advance on a silicon surface with two-beam interference using an 800 nm,50 fs femtosecond laser.The ultrafast dynamics of HSFL formation on the silicon surface of prefabricated LSFL under single femtosecond laser pulse irradiation were observed and analyzed for the first time using collinear pump-probe imaging method.In general,the evolution of the surface structure undergoes five sequential stages:the LSFL begins to split,becomes uniform HSFL,degenerates into an irregular LSFL,undergoes secondary splitting into a weakly uniform HSFL,and evolves into an irregular LSFL or is submerged.The results indicate that the local enhancement of the submerged nanocavity,or the nanoplasma,in the prefabricated LSFL ridge led to the splitting of the LSFL,and the thermodynamic effect drove the homogenization of the splitting LSFL,which evolved into HSFL.展开更多
The objective of this study is to improve the mechanical properties and machining performance of high thermal conductivity and low expansion silicon carbide dispersion-strengthened hypereutectic aluminum-silicon elect...The objective of this study is to improve the mechanical properties and machining performance of high thermal conductivity and low expansion silicon carbide dispersion-strengthened hypereutectic aluminum-silicon electronic packaging materials to meet the needs of aviation,aerospace,and electronic packaging fields.We used the powder metallurgy method and high-temperature hot pressing technology to prepare SiC/Al-Si composite materials with different SiC contents(5vol%,10vol%,15vol%,and 20vol%).The results showed that as the SiC content increased,the tensile strength of the composite material first increased and then decreased.The tensile strength was the highest when the SiC content was 15%;the sintering temperature significantly affected the composite material’s structural density and mechanical properties.Findings indicated 700℃was the optimal sintering and the optimal SiC content of SiC/Al-Si composite materials was between 10%and 15%.Besides,the sintering temperature should be strictly controlled to improve the material’s structural density and mechanical properties.展开更多
When preparing large monocrystalline silicon materials,severe carbon etching and silicide deposition often occur to the thermal system.Therefore,a suppression method that optimizes the upper insulation structure has b...When preparing large monocrystalline silicon materials,severe carbon etching and silicide deposition often occur to the thermal system.Therefore,a suppression method that optimizes the upper insulation structure has been proposed.Assisted by the finite element method,we calculated temperature distribution and carbon deposition of heater and heat shield,made the rule of silicide and temperature distributing in the system,and we explained the formation of impurity deposition.Our results show that the optimized thermal system reduces carbon etching loss on heat components.The lowered pressure of the furnace brings a rapid decrease of silicide deposition.The increase of the argon flow rate effectively inhibits CO and back diffusion.The simulated results agree well with the experiment observations,validating the effectiveness of the proposed method.展开更多
To grow high-quality and large-size monocrystalline silicon at low cost, we proposed a single-seed casting technique. To realize this technique, two challenges—polycrystalline nucleation on the crucible wall and disl...To grow high-quality and large-size monocrystalline silicon at low cost, we proposed a single-seed casting technique. To realize this technique, two challenges—polycrystalline nucleation on the crucible wall and dislocation multiplication inside the crystal—needed to be addressed. Numerical analysis was used to develop solutions for these challenges. Based on an optimized furnace structure and operating conditions from numerical analysis, experiments were performed to grow monocrystalline silicon using the single-seed casting technique. The results revealed that this technique is highly superior to the popular high-performance multicrystalline and multiseed casting mono-like techniques.展开更多
The thermal radiation properties of pyrolytic carbon(PyC)protective coatings for monocrystalline silicon furnace prepared by different processes were tested.The changes of normal emissivity of carbon materials caused ...The thermal radiation properties of pyrolytic carbon(PyC)protective coatings for monocrystalline silicon furnace prepared by different processes were tested.The changes of normal emissivity of carbon materials caused by PyC protective coatings were discussed,and the influence of phase structure and surface appearance on the thermal radiation properties was investigated.The results show that the thermal radiation properties of PyC protective coatings with the wave band of 5-25μm are better than C/C substrate,further,normal spectral emissivity of CVD PyC coating remains basically at 0.85-0.90,and the normal total emissivity can reach0.89,which shows high thermal radiation performance.For resin PyC coating and CVD PyC coating,the degree of graphitization are 44.53%and 16.28%respectively,and the R value of Raman spectrum are 0.964and 1.384 respectively.Relatively disorder graphite structure of the latter causes various vibration modes,and the spectral emissivity is better,so the thermal radiation property of CVD PyC coating is excellent.A lot of spherical particles exists on the surface of the CVD PyC coating,and the more interface and spacing of particles reduce the number of particles per unit volume.Therefore,the scattering of thermal radiation is strongly strengthened,and the spectral emissivity is higher.展开更多
An experiment for preparation of SOI films by using the scanning electron beam to modify the polycrystalline silicon on SiO2 is presented. This method takes on the epitaxial lateral growth of liquid phase with the cry...An experiment for preparation of SOI films by using the scanning electron beam to modify the polycrystalline silicon on SiO2 is presented. This method takes on the epitaxial lateral growth of liquid phase with the crystallon to form monocrystalline silicon films. The effects of the beam power density, scanning velocity, temperature of the substrates and the construction of samples on the quality of the monocrystalline silicon films were discussed. A good experimental result has been obtained, the monocrystalline silicon zone is nearly 200×25μm2.展开更多
The depth and nature of the subsurface damage in a silicon wafer will limit the performance of IC components. Damage microstructures of the silicon wafers ground by the #325, #600, and #2000 grinding wheels was analyz...The depth and nature of the subsurface damage in a silicon wafer will limit the performance of IC components. Damage microstructures of the silicon wafers ground by the #325, #600, and #2000 grinding wheels was analyzed. The re-sults show that many microcracks, fractures, and dislocation rosettes appear in the surface and subsurface of the wafer ground by the #325 grinding wheel. No obvious microstructure change exists. The amorphous layer with a thickness of about 100 nm, microcracks, high density dislocations, and polycrystalline silicon are observed in the subsurface of the wafer ground by the #600 grinding wheel. For the wafer ground by the #2000 grinding wheel, an amorphous layer of about 30 nm thickness, a polycrystalline silicon layer, a few dislocations, and an elastic deformation layer exist. In general, with the de-crease in grit size, the material removal mode changes from micro-fracture mode to ductile mode gradually.展开更多
The effects of particle size,gradation and solid loading of silicon nitride (Si_(3)N_(4)) on the rheological behavior and curing properties of ceramic slurry are studied by stereolithography (SLA).The results show tha...The effects of particle size,gradation and solid loading of silicon nitride (Si_(3)N_(4)) on the rheological behavior and curing properties of ceramic slurry are studied by stereolithography (SLA).The results show that the particle size of Si_(3)N_(4) powder has a signif icant influence on the rheological properties and stability of the slurry.When m_(D50=1.3μm):m_(D50=2.3μm)=3:7,the slurry viscosity is low and the sedimentation is slow.The most important thing is that with the increase of the solid loading of the slurry,the viscosity of the slurry increases,the stability becomes higher,and the curing thickness decreases.The curing thickness of Si_(3)N_(4) ceramic slurry with solid loading of 50 vol% can reach nearly 50μm.The above results finally show that the process optimizes the formulation of the slurry in rheological and curing properties.展开更多
Three-dimensional molecular dynamics simulations are carried out to study the mechanism of nanometric processing of ion implanted monocrystalline silicon surfaces. Lattice transformation is observed during implantatio...Three-dimensional molecular dynamics simulations are carried out to study the mechanism of nanometric processing of ion implanted monocrystalline silicon surfaces. Lattice transformation is observed during implantation and nano-indentation using radial distribution function and geometric criterion damage detection. Nano-indentation is simulated to study the changes of mechanical property. Implantation analysis shows the existence of amorphous phase.Indentation process shows the lattice evolution, which is beneficial for reducing fractures during processing. The indentation results reveal the reduction of brittleness and hardness of the implanted surface. The ion fluence is in direct proportion to the damage, and inverse to the hardness of the material. Experiments of ion implantation, nanoindentation, nano-scratching and nanometric cutting were carried out to verify the simulation results.展开更多
A calibration test was done in order to measure its sensitivity coefficient by an improved soil test device. The experimental result shows that the soil pressure min-sensor made of the monocrystalline silicon(SPM-MS)i...A calibration test was done in order to measure its sensitivity coefficient by an improved soil test device. The experimental result shows that the soil pressure min-sensor made of the monocrystalline silicon(SPM-MS)is proved to be good linear, high precision and less discrete that can fetch precise data in low pressure range even near by 0 point, which guarantees the reliability of the soil pressure test in geotechnical engineering.展开更多
A space monocrystalline silicon(c-Si) solar cell under low-energy(< 1 MeV) electron irradiation was investigated using noncontact photocarrier radiometry(PCR). Monte Carlo simulation(MCS) was employed to characteri...A space monocrystalline silicon(c-Si) solar cell under low-energy(< 1 MeV) electron irradiation was investigated using noncontact photocarrier radiometry(PCR). Monte Carlo simulation(MCS) was employed to characterize the effect of different energy electron irradiation on the c-Si solar cell. The carrier transport parameters(carrier lifetime, diffusion coefficient, and surface recombination velocities) were obtained by best fitting the experimental results with a theoretical one-dimensional two-layer PCR model. The results showed that the increase of the irradiation electron energy caused a large reduction of the carrier lifetime and diffusion length. Furthermore, the rear surface recombination velocity of the Si:p base of the solar cell at the irradiation electron energy of 1 Me V was dramatically enhanced due to 1 MeV electron passing through the whole cell. Short-circuit current(I sc) degradation evaluated by PCR was in good agreement with that obtained by electrical measurement.展开更多
文摘The monocrystalline silicon is a promising material that could be used in solar cells that convert light into electricity. Although the cost of ordinary silicon (Si) solar cells has decreased significantly over the past two decades, the conversion efficiency of these cells has remained relatively high. While solar cells have a great potential as a device of renewable energy, the high cost they incur per Watt continues to be a significant barrier to their widespread implementation. As a consequence, it is vital to conduct research into alternate materials that may be used in the construction of solar cells. The heterojunction solar cell (HJSC), which is based on n-type zinc oxide (n-ZnO) and p-type silicon (p-Si), is one of the numerous alternatives of the typical Si single homojunction solar cell. There are many deficiencies that can be found in the published research on n-ZnO/p-Si heterojunction solar cell. Inconsistencies in the stated value of open circuit voltage (V<sub>oc</sub>) of the solar cell are one example of deficiency. The absence of a full theoretical study to evaluate the potential of the solar cell structure is another deficiency that can be found in these researches. A lower value of experimentally obtained V<sub>OC</sub> in comparison to the theoretical prediction based on the band-gap between n-ZnO and p-Si. There needs to be more consensus among scientists regarding the optimal conditions for the growth of zinc oxide. Many software’s are available for simulating and optimizing the solar cells based on these parameters. For this purpose, in this dissertation, I provide computational results relevant to n-ZnO/p-Si HJSC to overcome deficiencies that have been identified. While modeling and simulating the potential of the solar cell structure with AFORS-HET, it is essential to consider the constraints that exist in the real world. AFORS-HET was explicitly designed to mimic the multilayer solar cell arrangement. In AFORS-HET, we can add up to seven layers for solar cell layout. By using this software, we can figure out the open circuit voltage (V<sub>OC</sub>), the short circuit current (J<sub>SC</sub>), the quantum efficiency (QE, %), the heterojunction energy band structure, and the power conversion efficiency (PCE).
基金Supported by the Shanghai Key Clinical Specialty,Shanghai Eye Disease Research Center(No.2022ZZ01003)the Science and Technology Commission of Shanghai(No.20DZ2270800).
文摘AIM:To evaluate the efficacy and safety of silicone oil(SO)as a corneal lubricant to improve visualization during vitrectomy.METHODS:Patients who underwent vitreoretinal surgery were divided into two groups.Group 1 was operated on with initial SO(Oxane 5700)as a corneal lubricant.Group 2 was operated on with initial lactated ringer’s solution(LRS)and then replaced with SO as required.Fundus clarity was scored during the surgery.Fluorescein staining was performed to determine the damage to corneal epithelium.RESULTS:Totally 114 eyes of 114 patients were included.Single SO use maintained a clear cornea and provided excellent visualization of surgical image.In group 1,the fundus clarity was grade 3 in 41/45 eyes and grade 2 in 4/45 eyes.In group 2,corneal edema frequently occurred after initial LRS use.The fundus clarity was grade 3 in 19/69 eyes,2 in 37/69 eyes and 1 in 13/69 eyes(P<0.05).SO was applied in 29 eyes of initial LRS use with subsequent corneal edema,which eliminated the corneal edema in 26 eyes.Corneal fluorescein staining score in group 1 was 0 in 28 eyes,1 in 11 eyes and 2 in 6 eyes,and 40,20 and 9,respectively,in group 2(all P>0.05).CONCLUSION:The use of SO as a corneal lubricant is effective and safe for preserving and improving corneal clarity and providing clear surgical field during vitrectomy.
基金This project was financially supported by the National Natural Science Foundation of China(31601244 and 31971843)the Guangdong Provincial Key Field Research and Development Plan Project,China(2019B020221003)the Modern Agricultural Industrial Technology System of Guangdong Province,China(2020KJ105).
文摘Fragrant rice has a high market value,and it is a popular rice type among consumers owing to its pleasant flavor.Plantation methods,nitrogen(N)fertilizers,and silicon(Si)fertilizers can affect the grain yield and fragrance of fragrant rice.However,the core commercial rice production attributes,namely the head rice yield(HRY)and 2-acetyl-1-pyrroline(2-AP)content of fragrant rice,under various nitrogen and silicon(N-Si)fertilization levels and different plantation methods remain unknown.The field experiment in this study was performed in the early seasons of 2018 and 2019 with two popular indica fragrant rice cultivars(Yuxiangyouzhan and Xiangyaxiangzhan).They were grown under six N-Si fertilization treatments(combinations of two levels of Si fertilizer,0 kg Si ha^(−1)(Si0)and 150 kg Si ha^(−1)(Si1),and three levels of N fertilizer,0 kg N ha^(−1)(N0),150 kg N ha^(−1)(N1),and 220 kg N ha^(−1)(N2))and three plantation methods(artificial transplanting(AT),mechanical transplanting(MT),and mechanical direct-seeding(MD)).The results showed that the N-Si fertilization treatments and all the plantation methods significantly affected the HRY and 2-AP content and related parameters of the two different fragrant rice cultivars.Compared with the Si0N0 treatment,the N-Si fertilization treatments resulted in higher HRY and 2-AP contents.The rates of brown rice,milled rice,head rice,and chalky rice of the fragrant rice also improved with the N-Si fertilization treatments.The N-Si fertilization treatments increased the activities of N metabolism enzymes and the accumulation of N and Si in various parts of the fragrant rice,and affected their antioxidant response parameters.The key parameters for the HRY and 2-AP content were assessed by redundancy analysis.Furthermore,the structural equation model revealed that the Si and N accumulation levels indirectly affected the HRY by affecting the N metabolism enzyme activity,N use efficiency,and grain quality of fragrant rice.Moreover,high N and Si accumulation directly promoted the 2-AP content or affected the antioxidant response parameters and indirectly regulated 2-AP synthesis.The interactions of the MT method with the N-Si fertilization treatments varied in the fragrant rice cultivars in terms of the HRY and 2-AP content,whereas the MD method was beneficial to the 2-AP content in both fragrant rice cultivars under the N-Si fertilization treatments.
基金Science&Technology Department of Sichuan Province(2022YFQ0041,2022NSFSC1725,2023NSFSC0214)China Agriculture Research System(CARS-07-B-1)+2 种基金The National Natural Science Foundation of China(32160428)Innovative Training Program for College Students(202311079040,S202311079112,CDUCX2023550)Undergraduate Education and Teaching Reform Project of Chengdu University(cdjgb2022186).
文摘Aluminum (Al) toxicity is a considerable factor limiting crop yield and biomass in acidic soil. Tartary buckwheatgrowing in acidic soil may suffer from Al poisoning. Here, we investigated the influence of Al stress on the growthof tartary buckwheat seedling roots, and the alleviation of Al stress by silicon (Si), as has been demonstrated inmany crops. Under Al stress, root growth (total root length, primary root length, root tips, root surface area, androot volume) was significantly inhibited, and Al and malondialdehyde (MDA) accumulated in the root tips. At thesame time, catalase (CAT) and ascorbate peroxidase activities, polyphenols, flavonoids, and 1,1-diphenyl-2-picrylhydrazyl(DPPH) and 2,2′-azinobis-(3-ethylbenzthiazoline-6-sulphonate) (ABTS) free-radical scavenging abilitywere significantly decreased. After the application of Si, root growth, Al accumulation, and oxidative damage wereimproved. Compared to Al-treated seedlings, the contents of ·O2− and MDA decreased by 29.39% and 25.22%,respectively. This was associated with Si-induced increases in peroxidase and CAT enzyme activity, flavonoidcompounds, and free-radical scavenging (DPPH and ABTS). The application of Si therefore has positive effectson Al toxicity in tartary buckwheat roots by reducing Al accumulation in the roots and maintaining oxidationhomeostasis.
文摘[Objectives]This study was conducted to investigate the scientific application of silicon fertilizer in rice cultivation,one of the staple crops.[Methods]In 2022,Yandu District carried out a special experiment and field demonstration study on the effects of foliar application of Zhengda water-soluble silicon fertilizer on rice production.[Results]The preliminary results showed that①Zhengda water-soluble silicon fertilizer could effectively improve the growth and development of rice and improve the population quality.The peak number of tillers,productive tiller percentage,number of effective panicles and number of effective grains per panicle increased by 6.7%,5.8%,5.5%,and 1.2%,respectively.②The yield and processing quality were improved.After applying silicon fertilizer,the yield per unit area increased by about 6.8%,and the unpolished rice yield,milled rice yield and head rice yield increased by 0.7%,1.94%and 2.15%respectively.[Conclusions]The demonstration application of silicon fertilizer in field cultivation of rice in Yandu District further proves previous research conclusions and has important practical significance.
基金Supported by National Key R and D Program of China,No.2020YFC2008200.
文摘BACKGROUND Endophthalmitis occurring in silicone oil-filled eyes is a very rare occurrence,with reported incidence rates ranging between 0.07%and 0.039%.Traditional methods of management of infectious endophthalmitis include the removal of silicone oil,washout of the vitreous cavity,administration of intravitreal antibiotics,and reinjection of silicone oil.CASE SUMMARY Herein,we report the case of a 39-year-old man with unilateral endophthalmitis after pars plana vitrectomy and silicone oil tamponade.Intravitreal injections of full-dose antibiotics and anterior chamber washout were used to treat the patient.No signs of retinal toxicity were observed during the follow-up period.CONCLUSION Intravitreal full-dose antibiotic injections and anterior chamber washout are promising alternatives to traditional therapies for endophthalmitis in silicone oilfilled eyes.
基金the support of the Joint Funds of the Natural Science Foundation of Hubei Province(2022CFD130)the Technology Innovation Project of Hubei Province(Key Program,No.2023BEB010)+1 种基金the Key Research and Development Program of Hubei Province(No.2021BGD015)the Knowledge Innovation Project of Wuhan(No.2022010801010259).
文摘An experimental investigation into the thermal conductivity of CF-SiC two-phase composite asphalt concrete is presented.The main objective of this study was to verify the possibility of using SiC powder instead of mineral powder as the thermal conductive filler to prepare a new type of asphalt concrete and improve the efficiency of electrothermal snow and ice melting systems accordingly.The thermal conductivity of asphalt concrete prepared with different thermally conductive fillers was tested by a transient plane source method,and the related performances were measured.Then the temperature rise rate and surface temperature were studied through field heating tests.Finally,the actual ice melting efficiency of the thermally conductive asphalt concrete was evaluated using an effective electrothermal system.As shown by the experimental results,the composite made of SiC powder and carbon fiber has a high thermal conductivity.When SiC replaces mineral powder,the thermal conductivity of the asphalt mixture increases first and then decreases with the increase of carbon fiber content.In the present study,in particular,the thermal conductivity attained a peak when the carbon fiber content was 0.2%of the aggregate mass.
基金supports from the National Natural Science Foundation of China(12074123,12174108)the Foundation of‘Manufacturing beyond limits’of Shanghai‘Talent Program'of Henan Academy of Sciences.
文摘Femtosecond laser-induced periodic surface structures(LIPSS)have been extensively studied over the past few decades.In particular,the period and groove width of high-spatial-frequency LIPSS(HSFL)is much smaller than the diffraction limit,making it a useful method for efficient nanomanufacturing.However,compared with the low-spatial-frequency LIPSS(LSFL),the structure size of the HSFL is smaller,and it is more easily submerged.Therefore,the formation mechanism of HSFL is complex and has always been a research hotspot in this field.In this study,regular LSFL with a period of 760 nm was fabricated in advance on a silicon surface with two-beam interference using an 800 nm,50 fs femtosecond laser.The ultrafast dynamics of HSFL formation on the silicon surface of prefabricated LSFL under single femtosecond laser pulse irradiation were observed and analyzed for the first time using collinear pump-probe imaging method.In general,the evolution of the surface structure undergoes five sequential stages:the LSFL begins to split,becomes uniform HSFL,degenerates into an irregular LSFL,undergoes secondary splitting into a weakly uniform HSFL,and evolves into an irregular LSFL or is submerged.The results indicate that the local enhancement of the submerged nanocavity,or the nanoplasma,in the prefabricated LSFL ridge led to the splitting of the LSFL,and the thermodynamic effect drove the homogenization of the splitting LSFL,which evolved into HSFL.
文摘The objective of this study is to improve the mechanical properties and machining performance of high thermal conductivity and low expansion silicon carbide dispersion-strengthened hypereutectic aluminum-silicon electronic packaging materials to meet the needs of aviation,aerospace,and electronic packaging fields.We used the powder metallurgy method and high-temperature hot pressing technology to prepare SiC/Al-Si composite materials with different SiC contents(5vol%,10vol%,15vol%,and 20vol%).The results showed that as the SiC content increased,the tensile strength of the composite material first increased and then decreased.The tensile strength was the highest when the SiC content was 15%;the sintering temperature significantly affected the composite material’s structural density and mechanical properties.Findings indicated 700℃was the optimal sintering and the optimal SiC content of SiC/Al-Si composite materials was between 10%and 15%.Besides,the sintering temperature should be strictly controlled to improve the material’s structural density and mechanical properties.
基金supported by the National Natural Science Foundation of China(No.61533014)the Natural Science Foundation of Shaanxi Province(No.2019JQ-734)。
文摘When preparing large monocrystalline silicon materials,severe carbon etching and silicide deposition often occur to the thermal system.Therefore,a suppression method that optimizes the upper insulation structure has been proposed.Assisted by the finite element method,we calculated temperature distribution and carbon deposition of heater and heat shield,made the rule of silicide and temperature distributing in the system,and we explained the formation of impurity deposition.Our results show that the optimized thermal system reduces carbon etching loss on heat components.The lowered pressure of the furnace brings a rapid decrease of silicide deposition.The increase of the argon flow rate effectively inhibits CO and back diffusion.The simulated results agree well with the experiment observations,validating the effectiveness of the proposed method.
基金partly supported by the New Energy and Industrial Technology Development Organization (NEDO) under the Ministry of Economy,Trade and Industry (METI),Japan
文摘To grow high-quality and large-size monocrystalline silicon at low cost, we proposed a single-seed casting technique. To realize this technique, two challenges—polycrystalline nucleation on the crucible wall and dislocation multiplication inside the crystal—needed to be addressed. Numerical analysis was used to develop solutions for these challenges. Based on an optimized furnace structure and operating conditions from numerical analysis, experiments were performed to grow monocrystalline silicon using the single-seed casting technique. The results revealed that this technique is highly superior to the popular high-performance multicrystalline and multiseed casting mono-like techniques.
基金Sponsored by the National High Technology Research and Development Program of China(863 Program)(Grant No.2009AA035301)the ChinaPostdoctoral Science Foundation(Grant No.2012M511544)
文摘The thermal radiation properties of pyrolytic carbon(PyC)protective coatings for monocrystalline silicon furnace prepared by different processes were tested.The changes of normal emissivity of carbon materials caused by PyC protective coatings were discussed,and the influence of phase structure and surface appearance on the thermal radiation properties was investigated.The results show that the thermal radiation properties of PyC protective coatings with the wave band of 5-25μm are better than C/C substrate,further,normal spectral emissivity of CVD PyC coating remains basically at 0.85-0.90,and the normal total emissivity can reach0.89,which shows high thermal radiation performance.For resin PyC coating and CVD PyC coating,the degree of graphitization are 44.53%and 16.28%respectively,and the R value of Raman spectrum are 0.964and 1.384 respectively.Relatively disorder graphite structure of the latter causes various vibration modes,and the spectral emissivity is better,so the thermal radiation property of CVD PyC coating is excellent.A lot of spherical particles exists on the surface of the CVD PyC coating,and the more interface and spacing of particles reduce the number of particles per unit volume.Therefore,the scattering of thermal radiation is strongly strengthened,and the spectral emissivity is higher.
文摘An experiment for preparation of SOI films by using the scanning electron beam to modify the polycrystalline silicon on SiO2 is presented. This method takes on the epitaxial lateral growth of liquid phase with the crystallon to form monocrystalline silicon films. The effects of the beam power density, scanning velocity, temperature of the substrates and the construction of samples on the quality of the monocrystalline silicon films were discussed. A good experimental result has been obtained, the monocrystalline silicon zone is nearly 200×25μm2.
基金This study was financially supported by the National Natural Science Foundation of China in Major Project Program (No. 50390061)the National Science Fund for Distinguished Young Scholars (No. 50325518).
文摘The depth and nature of the subsurface damage in a silicon wafer will limit the performance of IC components. Damage microstructures of the silicon wafers ground by the #325, #600, and #2000 grinding wheels was analyzed. The re-sults show that many microcracks, fractures, and dislocation rosettes appear in the surface and subsurface of the wafer ground by the #325 grinding wheel. No obvious microstructure change exists. The amorphous layer with a thickness of about 100 nm, microcracks, high density dislocations, and polycrystalline silicon are observed in the subsurface of the wafer ground by the #600 grinding wheel. For the wafer ground by the #2000 grinding wheel, an amorphous layer of about 30 nm thickness, a polycrystalline silicon layer, a few dislocations, and an elastic deformation layer exist. In general, with the de-crease in grit size, the material removal mode changes from micro-fracture mode to ductile mode gradually.
基金Funded by National Natural Science Foundation of China (No.43200021)。
文摘The effects of particle size,gradation and solid loading of silicon nitride (Si_(3)N_(4)) on the rheological behavior and curing properties of ceramic slurry are studied by stereolithography (SLA).The results show that the particle size of Si_(3)N_(4) powder has a signif icant influence on the rheological properties and stability of the slurry.When m_(D50=1.3μm):m_(D50=2.3μm)=3:7,the slurry viscosity is low and the sedimentation is slow.The most important thing is that with the increase of the solid loading of the slurry,the viscosity of the slurry increases,the stability becomes higher,and the curing thickness decreases.The curing thickness of Si_(3)N_(4) ceramic slurry with solid loading of 50 vol% can reach nearly 50μm.The above results finally show that the process optimizes the formulation of the slurry in rheological and curing properties.
基金Supported by the National Basic Research Program of China("973" Program,No.2011CB706703)
文摘Three-dimensional molecular dynamics simulations are carried out to study the mechanism of nanometric processing of ion implanted monocrystalline silicon surfaces. Lattice transformation is observed during implantation and nano-indentation using radial distribution function and geometric criterion damage detection. Nano-indentation is simulated to study the changes of mechanical property. Implantation analysis shows the existence of amorphous phase.Indentation process shows the lattice evolution, which is beneficial for reducing fractures during processing. The indentation results reveal the reduction of brittleness and hardness of the implanted surface. The ion fluence is in direct proportion to the damage, and inverse to the hardness of the material. Experiments of ion implantation, nanoindentation, nano-scratching and nanometric cutting were carried out to verify the simulation results.
文摘A calibration test was done in order to measure its sensitivity coefficient by an improved soil test device. The experimental result shows that the soil pressure min-sensor made of the monocrystalline silicon(SPM-MS)is proved to be good linear, high precision and less discrete that can fetch precise data in low pressure range even near by 0 point, which guarantees the reliability of the soil pressure test in geotechnical engineering.
文摘A space monocrystalline silicon(c-Si) solar cell under low-energy(< 1 MeV) electron irradiation was investigated using noncontact photocarrier radiometry(PCR). Monte Carlo simulation(MCS) was employed to characterize the effect of different energy electron irradiation on the c-Si solar cell. The carrier transport parameters(carrier lifetime, diffusion coefficient, and surface recombination velocities) were obtained by best fitting the experimental results with a theoretical one-dimensional two-layer PCR model. The results showed that the increase of the irradiation electron energy caused a large reduction of the carrier lifetime and diffusion length. Furthermore, the rear surface recombination velocity of the Si:p base of the solar cell at the irradiation electron energy of 1 Me V was dramatically enhanced due to 1 MeV electron passing through the whole cell. Short-circuit current(I sc) degradation evaluated by PCR was in good agreement with that obtained by electrical measurement.
