Stripping units take a key role in the neutral particle analyzer(NPA).A renovated gas-stripping unit was constructed for the newly designed E//B NPA.Using H_(2)as the working gas,we measured the gas inlet pressure(P_(...Stripping units take a key role in the neutral particle analyzer(NPA).A renovated gas-stripping unit was constructed for the newly designed E//B NPA.Using H_(2)as the working gas,we measured the gas inlet pressure(P_(0))and vacuum chamber pressure(P_(3)).The pressure distribution inside the gas-stripping room was calculated with Ansys Fluent,using the measured P_(0)and P_(3)as boundary conditions.The stripping efficiency of the stripping unit was then simulated utilizing the Geant4 Monte Carlo code for the H and D particles.The pressure P_(0)=40 Pa,which is one-sixth of what found in the previous design and corresponds to a thickness of 1.27×10^(17)atoms∕cm^(2),was obtained as the optimum working pressure for the upgraded stripping unit.An 50 kV electron cyclotron resonance(ECR)ion source platform was designed and constructed for E//B NPA calibration,and its performance has been measured.Using the ECR ion source platform,we measured the efficiency of the stripping unit through an inverse experiment with proton beams.We compared the current ratios of measurements with and without H_(2)gas to Geant4 simulation results.We found adequate agreement between the overall trends of the experiment and the simulation.The significant deviation for incident energies below 20 keV may result from the scattering effects of low-energy protons,leading to reduced accuracy in single-scattering physics in Geant4 simulations.Applying the scattering corrections observed in the reverse experiments obtains more accurate stripping efficiencies for H and D atoms in the energy range of 20–200 keV and the global efficiency with the maximum values of 95.0%for H atoms and 78.9%for D atoms at 200 keV.展开更多
Traditional transgenic detection methods require high test conditions and struggle to be both sensitive and efficient.In this study,a one-tube dual recombinase polymerase amplification(RPA)reaction system for CP4-EPSP...Traditional transgenic detection methods require high test conditions and struggle to be both sensitive and efficient.In this study,a one-tube dual recombinase polymerase amplification(RPA)reaction system for CP4-EPSPS and Cry1Ab/Ac was proposed and combined with a lateral flow immunochromatographic assay,named“Dual-RPA-LFD”,to visualize the dual detection of genetically modified(GM)crops.In which,the herbicide tolerance gene CP4-EPSPS and the insect resistance gene Cry1Ab/Ac were selected as targets taking into account the current status of the most widespread application of insect resistance and herbicide tolerance traits and their stacked traits.Gradient diluted plasmids,transgenic standards,and actual samples were used as templates to conduct sensitivity,specificity,and practicality assays,respectively.The constructed method achieved the visual detection of plasmid at levels as low as 100 copies,demonstrating its high sensitivity.In addition,good applicability to transgenic samples was observed,with no cross-interference between two test lines and no influence from other genes.In conclusion,this strategy achieved the expected purpose of simultaneous detection of the two popular targets in GM crops within 20 min at 37°C in a rapid,equipmentfree field manner,providing a new alternative for rapid screening for transgenic assays in the field.展开更多
The practice of intercropping leguminous and gramineous crops is used for promoting sustainable agriculture,optimizing resource utilization,enhancing biodiversity,and reducing reliance on petroleum products.However,pr...The practice of intercropping leguminous and gramineous crops is used for promoting sustainable agriculture,optimizing resource utilization,enhancing biodiversity,and reducing reliance on petroleum products.However,promoting conventional intercropping strategies in modern agriculture can prove challenging.The innovative technology of soybean maize strip intercropping(SMSI)has been proposed as a solution.This system has produced remarkable results in improving domestic soybean and maize production for both food security and sustainable agriculture.In this article,we provide an overview of SMSI and explain how it differs from traditional intercropping.We also discuss the core principles that foster higher yields and the prospects for its future development.展开更多
Refinery sour water primarily originates from the tops of towers in various units and coker condensate,and cannot be discharged directly to a wastewater treatment plant due to high levels of chemical oxygen demand(COD...Refinery sour water primarily originates from the tops of towers in various units and coker condensate,and cannot be discharged directly to a wastewater treatment plant due to high levels of chemical oxygen demand(COD)and organic sulfur contents.Even after the recovery of H_(2)S from the sour water by the stripping process,the effluent still contains a high concentration of dissolved organic sulfur(DOS),which can have a huge bad influence.While chemical composition of dissolved organic matter(DOM)in refinery wastewater has been extensively studied,the investigation of recalcitrant DOS from sour waters remains unclear.In the present study,chemical composition of sour water DOMs(especially DOS)was investigated using fluorescence spectroscopy(excitation-emission matrix,EEM)and mass spectrometry,including gas chromatography-mass spectrometry(GC-MS)and high-resolution Orbitrap MS.The GC-MS and EEM results showed that volatile and low-aromaticity compounds were effectively removed during the stripping process,while compounds with high hydrophilicity and humification degree were found to be more recalcitrant.The Orbitrap MS results showed that weak-polar oxygenated sulfur compounds were easier to be removed than oxygenated compounds.However,the effluent still contained significant amounts of sulfur-containing compounds with multiple sulfur atoms,particularly in the form of highly unsaturated and aromatic compounds.The Orbitrap MS/MS results of CHOS-containing compounds from the effluent indicate that the sulfur atoms may exist as sulfonates,disulfide bonds,thioethers.Understanding the composition and structure of sour water DOS is crucial for the development of effective treatment processes that can target polysulfide compounds and minimize their impact on the environment.展开更多
The complex producing procedures and high energy-consuming limit the large-scale production and application of advanced high-strength steels(AHSSs).In this study,the direct strip casting(DSC)technology with unique sub...The complex producing procedures and high energy-consuming limit the large-scale production and application of advanced high-strength steels(AHSSs).In this study,the direct strip casting(DSC)technology with unique sub-rapid solidification characteristics and cost advantages was applied to the production of low-alloy Si-Mn steel with the help of quenching&partitioning(Q&P)concept to address these issues.Compared this method with the conventional compact strip production(CSP)process,the initial microstructure formed under different solidification conditions and the influence of heat treatment processes on the final mechanical properties were in-vestigated.The results show that the initial structure of the DSC sample is a dual-phase structure composed of fine lath martensite and bainite,while the initial structure of the CSP sample consists of pearlite and ferrite.The volume fraction and carbon content of retained austenite(RA)in DSC samples are usually higher than those in CSP samples after the same Q&P treatment.DSC samples typically demonstrate better comprehensive mechanical properties than the CSP sample.The DSC sample partitioned at 300℃ for 300 s(DSC-Pt300)achieves the best comprehensive mechanical properties,with yield strength(YS)of 1282 MPa,ultimate tensile strength(UTS)of 1501 MPa,total elongation(TE)of 21.5%,and product of strength and elongation(PSE)as high as 32.3 GPa·%.These results indicate that the excellent mechanical properties in low-alloy Si-Mn steel can be obtained through a simple process(DSC-Q&P),which also demonstrates the superiority of DSC technology in manufacturing AHSSs.展开更多
The interfacial wettability and heat transfer behavior are crucial in the strip casting of high phosphorus-containing steel.A hightemperature simulation of strip casting was conducted using the droplet solidification ...The interfacial wettability and heat transfer behavior are crucial in the strip casting of high phosphorus-containing steel.A hightemperature simulation of strip casting was conducted using the droplet solidification technique with the aims to reveal the effects of phosphorus content on interfacial wettability,deposited film,and interfacial heat transfer behavior.Results showed that when the phosphorus content increased from 0.014wt%to 0.406wt%,the mushy zone enlarged,the complete solidification temperature delayed from1518.3 to 1459.4℃,the final contact angle decreased from 118.4°to 102.8°,indicating improved interfacial contact,and the maximum heat flux increased from 6.9 to 9.2 MW/m2.Increasing the phosphorus content from 0.081wt%to 0.406wt%also accelerated the film deposition rate from 1.57 to 1.73μm per test,resulting in a thickened naturally deposited film with increased thermal resistance that advanced the transition point of heat transfer from the fifth experiment to the third experiment.展开更多
Counterfeiting of modern banknotes poses a significant challenge,prompting the use of various preventive measures.One such measure is the magnetic anti-counterfeiting strip.However,due to its inherent weak magnetic pr...Counterfeiting of modern banknotes poses a significant challenge,prompting the use of various preventive measures.One such measure is the magnetic anti-counterfeiting strip.However,due to its inherent weak magnetic properties,visualizing its magnetic distribution has been a longstanding challenge.In this work,we introduce an innovative method by using a fiber optic diamond probe,a highly sensitive quantum sensor designed specifically for detecting extremely weak magnetic fields.We employ this probe to achieve high-resolution imaging of the magnetic fields associated with the RMB 50denomination anti-counterfeiting strip.Additionally,we conduct computer simulations by using COMSOL Multiphysics software to deduce the potential geometric characteristics and material composition of the magnetic region within the anti-counterfeiting strip.The findings and method presented in this study hold broader significance,extending the RMB 50 denomination to various denominations of the Chinese currency and other items that employ magnetic anti-counterfeiting strips.These advances have the potential to significantly improve and promote security measures in order to prevent the banknotes from being counterfeited.展开更多
An internal defect meter is an instrument to detect the internal inclusion defects of cold-rolled strip steel.The detection accuracy of the equipment can be evaluated based on the similarity of the multiple detection ...An internal defect meter is an instrument to detect the internal inclusion defects of cold-rolled strip steel.The detection accuracy of the equipment can be evaluated based on the similarity of the multiple detection data obtained for the same steel coil.Based on the cosine similarity model and eigenvalue matrix model,a comprehensive evaluation method to calculate the weighted average of similarity is proposed.Results show that the new method is consistent with and can even replace artificial evaluation to realize the automatic evaluation of strip defect detection results.展开更多
Many spot defects were found on the surface of a cold-rolled Fe-36%Ni alloy strip produced in a factory,which seriously affected the surface quality of the product.Through metallographic microscopy and scanning electr...Many spot defects were found on the surface of a cold-rolled Fe-36%Ni alloy strip produced in a factory,which seriously affected the surface quality of the product.Through metallographic microscopy and scanning electron microscopy analyses,it was found that the spot defects were caused by the residual oxide layer on the surface of the cold-rolled Fe-36%Ni alloy strip after hydrogen annealing.By properly increasing the grinding amount of the blank before cold rolling to remove the oxide layer,the spot defects on the surface of the cold-rolled strip were effectively eliminated,and the surface quality of the product was ensured.展开更多
Higher requirements for the accuracy of relevant models are put throughout the transformation and upgrade of the iron and steel sector to intelligent production.It has been difficult to meet the needs of the field wit...Higher requirements for the accuracy of relevant models are put throughout the transformation and upgrade of the iron and steel sector to intelligent production.It has been difficult to meet the needs of the field with the usual prediction model of mechanical properties of hotrolled strip.Insufficient data and difficult parameter adjustment limit deep learning models based on multi-layer networks in practical applications;besides,the limited discrete process parameters used make it impossible to effectively depict the actual strip processing process.In order to solve these problems,this research proposed a new sampling approach for mechanical characteristics input data of hot-rolled strip based on the multi-grained cascade forest(gcForest)framework.According to the characteristics of complex process flow and abnormal sensitivity of process path and parameters to product quality in the hot-rolled strip production,a three-dimensional continuous time series process data sampling method based on time-temperature-deformation was designed.The basic information of strip steel(chemical composition and typical process parameters)is fused with the local process information collected by multi-grained scanning,so that the next link’s input has both local and global features.Furthermore,in the multi-grained scanning structure,a sub sampling scheme with a variable window was designed,so that input data with different dimensions can get output characteristics of the same dimension after passing through the multi-grained scanning structure,allowing the cascade forest structure to be trained normally.Finally,actual production data of three steel grades was used to conduct the experimental evaluation.The results revealed that the gcForest-based mechanical property prediction model outperforms the competition in terms of comprehensive performance,ease of parameter adjustment,and ability to sustain high prediction accuracy with fewer samples.展开更多
As a near-net-shape technology,the twin-roll strip casting(TRC)process can be considered to apply to the fabrication of TiAl alloy sheets.However,the control of the grain distribution is very important in strip castin...As a near-net-shape technology,the twin-roll strip casting(TRC)process can be considered to apply to the fabrication of TiAl alloy sheets.However,the control of the grain distribution is very important in strip casting because the mechanical properties of strips are directly determined by the solidification microstructure.A three-dimensional(3D)cellular automation finite-element(CAFE)model based on ProCAST software was established to simulate the solidification microstructure of Ti-43Al alloy.Then,the influence of casting temperature and the maximum nucleation density(nmax)on the solidification microstructure was investigated in detail.The simulation results provide a good explanation and prediction for the solidification microstructure in the molten pool before leaving the kissing point.Experimental and simulated microstructure show the common texture<001>orientation in the columnar grains zone.Finally,the microstructure evolution of the Ti-43Al alloy was analyzed and the solidification phase transformation path during the TSC process was determined,i.e.,L→L+β→β→β+α→α+γ+β/B2 phase under a faster cooling rate and L→L+β→β→β+α→γ+lamellar(α_(2)+γ)+β/B2 phase under a slower cooling rate.展开更多
AIM:To report the outcomes of three cases of corneal perforation managed with simultaneous tectonic Descemet stripping endothelial keratoplasty(t-DSEK)and tectonic Bowman layer transplant(t-BLT)as an alternative to te...AIM:To report the outcomes of three cases of corneal perforation managed with simultaneous tectonic Descemet stripping endothelial keratoplasty(t-DSEK)and tectonic Bowman layer transplant(t-BLT)as an alternative to tectonic penetrating keratoplasty(t-PKP).METHODS:Three eyes of three patients receiving simultaneous t-DSEK and t-BLT for corneal perforation were included.The technique for DSEK was modified depending on individual requirements.The t-BLT technique was standardised using an 8 mm graft and fixated with a running suture.Success was measured by the ability of this procedure to close a corneal perforation.RESULTS:All three cases achieved tectonic eye globe restoration and remained stable during the minimum 3-month observation period.Reinterventions were relatively common:2 cases required amniotic membrane transplant for persistent epithelial defects.One case required DSEK rebubbling.One case developed angle closure glaucoma requiring surgical peripheral iridectomy.CONCLUSION:Simultaneous t-DSEK and t-BLT may be a useful strategy for the management of corneal perforation as an alternative management to t-PKP for selected cases.展开更多
Bird fauna checklists are important tools in ecology, biology, and conservation planning for scientists, stakeholders, and decision-makers. Despite its small area, the Gaza Strip (365 km<sup>2</sup>) has a...Bird fauna checklists are important tools in ecology, biology, and conservation planning for scientists, stakeholders, and decision-makers. Despite its small area, the Gaza Strip (365 km<sup>2</sup>) has a relatively large variety of resident and migratory bird fauna. Therefore, the current study aimed to provide an updated checklist of all bird fauna living in or inhabiting the Gaza Strip. Direct field observations using binoculars, continuous visits to zoos, pet stores and biology museums, discussion with bird hunters, follow-up of news and social networking sites, review of scientific publications and photography were the main tools to satisfy the purpose of the study. At least 250 bird species collected from different sources occur in the Gaza Strip and are included in the checklist. This list will not be static, but is inevitably subject to additions and changes in the face of times. The current 250 bird species of the Gaza Strip represent 45.4% of the 551 species of birds living in Palestine. The bird species were found to belong to 21 orders and 61 families. The Passeriformes (passerines) represented the largest order with 96 species of birds (38.4%), followed by the Charadriiformes 54 (21.6%), the Accipitriformes 18 (7.2%), Anseriformes 17 (6.8%) and Pelecaniformes 14 (5.6%), while the other orders represented the remaining percentage (20.4%). With regard to families, the Scolopacidae represented the largest family with 22 species of birds (8.8%), followed by the Anatidae and Accipitridae 17 for each (6.8%), the Muscicapidae 16 (6.4%) and Chariidridae and Fringillidae 11 for each (4.4%), while the other families represented the remaining percentage (62.4%). According to the IUCN regional threat categories, 226 species (90.4%) were Least Concern (LC), 12 (4.8%) were Near Threatened (NT), 6 (2.4%) were Vulnerable (VU), 4 (1.6%) were Endangered (EN) and 2 (0.8%) were Critically Endangered (CR). In conclusion, the study recommends a sustainable control of bird hunting and trafficking in addition to building prestigious centers and museums for studying and documenting birds in the Gaza Strip.展开更多
The Mediterranean Sea is home to an interesting biodiversity. The current cumulative and descriptive study aims to enumerate some relatively large marine mammals, reptiles, and fishes that have been spotted, caught, b...The Mediterranean Sea is home to an interesting biodiversity. The current cumulative and descriptive study aims to enumerate some relatively large marine mammals, reptiles, and fishes that have been spotted, caught, by-caught, or stranded on the coast of the Gaza Strip, Palestine, which extends about 42 km along the Mediterranean Sea. This 20-year study from 2003 to 2022 relied much on frequent field visits, meetings, and discussions with stakeholders, following local media sites and social media pages, and photography. The study recorded at least 26 giants or relatively large marine organisms on the Mediterranean coast of the Gaza Strip, Palestine. Certainly, the coming years may bring other marine organisms of relatively large sizes. Marine mammals included three species of cetaceans with the Fin Whale (Balaenoptera physalus) being the largest mammal and even the largest animal ever recorded in this study. Marine reptiles included three species of sea turtles, the largest of which is the Leatherback Sea Turtle (Dermochelys coriacea), which is in fact the world’s largest sea turtle. The bony fishes were represented by ten species, the largest of which was the Ocean Sunfish (Mola mola), which is the largest bony fish in the world. The cartilaginous fishes included ten species with the largest specimens encountered were the Shortfin Shark (Isurus oxyrinchus), Bluntnose Sixgill Shark (Hexanchus griseus), Scalloped Hammerhead Shark (Sphyrna lewini), and Giant Devil Ray (Mobula mobular). Seabirds were not included in the study. The Alexandria Pompano (Alectis alexandrinus) and the Silver-Cheeked Toadfish (Lagocephalus sceleratus), which are bony fishes, appear to be the relatively smallest marine organisms recorded here. In conclusion, the role of the various parties must be coordinated to ensure the sustainability of human activities and their compatibility with the task of conserving local marine biota, including the gigantic or relatively large ones.展开更多
Polysurfacic tori or kideas are three-dimensional objects formed by rotating a regular polygon around a central axis. These toric shapes are referred to as “polysurfacic” because their characteristics, such as the n...Polysurfacic tori or kideas are three-dimensional objects formed by rotating a regular polygon around a central axis. These toric shapes are referred to as “polysurfacic” because their characteristics, such as the number of sides or surfaces separated by edges, can vary in a non-trivial manner depending on the degree of twisting during the revolution. We use the term “Kideas” to specifically denote these polysurfacic tori, and we represent the number of sides (referred to as “facets”) of the original polygon followed by a point, while the number of facets from which the torus is twisted during its revolution is indicated. We then explore the use of concave regular polygons to generate Kideas. We finally give acceleration for the algorithm for calculating the set of prime numbers.展开更多
Artificial cementation is a method commonly used to enhance and improve soil properties. This paper investigates the effect of using different amounts of cement on soil strength parameters and soil bearing capacity, u...Artificial cementation is a method commonly used to enhance and improve soil properties. This paper investigates the effect of using different amounts of cement on soil strength parameters and soil bearing capacity, using the finite element method. Experimental tests are conducted on soil samples with different amounts of Portland cement. A 2-D numerical model is created and validated using the numerical modelling software, COMSOL Multiphysics 5.6 software. The study finds that the cohesion, and the angle of the internal friction of the soil samples increase significantly as a result of adding 1%, 2%, and 4% of Portland cement. The results demonstrate that the stresses and strain under the strip footing proposed decrease by 3.24% and 7.42%. Moreover, the maximum displacement also decreases by 1.47% and 2.97%, as a result of adding cements of 2% and 4%. The bearing capacity values obtained are therefore excellent, especially when using the 2% and 4% cement. The increase identified is due to the increased values of the bearing capacity factors. It is concluded that from an economic viewpoint, using 2% cement is the best option.展开更多
A miniaturized broadband Wilkinson power divider is proposed. Micro-strip branch lines are introduced to replace multiple resistors used in multi-stage Wilkinson power dividers to increase the bandwidth of single-stag...A miniaturized broadband Wilkinson power divider is proposed. Micro-strip branch lines are introduced to replace multiple resistors used in multi-stage Wilkinson power dividers to increase the bandwidth of single-stage Wilkinson power dividers. To demonstrate its performance, an improved single-stage Wilkinson power divider with four micro-strip branch lines was designed. Simulated results show that the insert loss is better than 3.2 dB, the input return loss, output return loss, and isolation are better than 15 dB respectively, across a 76% bandwidth from 18 to 40 GHz. .展开更多
基金supported by the National MCF Energy R&D Program of China(MOST 2018YFE0310200)in part by the National Natural Science Foundation of China(Nos.11705242,11805138,12175156)in part by the Fundamental Research Funds for the Central Universities(Nos.YJ201820,YJ201954)in China.
文摘Stripping units take a key role in the neutral particle analyzer(NPA).A renovated gas-stripping unit was constructed for the newly designed E//B NPA.Using H_(2)as the working gas,we measured the gas inlet pressure(P_(0))and vacuum chamber pressure(P_(3)).The pressure distribution inside the gas-stripping room was calculated with Ansys Fluent,using the measured P_(0)and P_(3)as boundary conditions.The stripping efficiency of the stripping unit was then simulated utilizing the Geant4 Monte Carlo code for the H and D particles.The pressure P_(0)=40 Pa,which is one-sixth of what found in the previous design and corresponds to a thickness of 1.27×10^(17)atoms∕cm^(2),was obtained as the optimum working pressure for the upgraded stripping unit.An 50 kV electron cyclotron resonance(ECR)ion source platform was designed and constructed for E//B NPA calibration,and its performance has been measured.Using the ECR ion source platform,we measured the efficiency of the stripping unit through an inverse experiment with proton beams.We compared the current ratios of measurements with and without H_(2)gas to Geant4 simulation results.We found adequate agreement between the overall trends of the experiment and the simulation.The significant deviation for incident energies below 20 keV may result from the scattering effects of low-energy protons,leading to reduced accuracy in single-scattering physics in Geant4 simulations.Applying the scattering corrections observed in the reverse experiments obtains more accurate stripping efficiencies for H and D atoms in the energy range of 20–200 keV and the global efficiency with the maximum values of 95.0%for H atoms and 78.9%for D atoms at 200 keV.
基金supported by the Scientific and Innovative Action Plan of Shanghai(21N31900800)Shanghai Rising-Star Program(23QB1403500)+4 种基金the Shanghai Sailing Program(20YF1443000)Shanghai Science and Technology Commission,the Belt and Road Project(20310750500)Talent Project of SAAS(2023-2025)Runup Plan of SAAS(ZP22211)the SAAS Program for Excellent Research Team(2022(B-16))。
文摘Traditional transgenic detection methods require high test conditions and struggle to be both sensitive and efficient.In this study,a one-tube dual recombinase polymerase amplification(RPA)reaction system for CP4-EPSPS and Cry1Ab/Ac was proposed and combined with a lateral flow immunochromatographic assay,named“Dual-RPA-LFD”,to visualize the dual detection of genetically modified(GM)crops.In which,the herbicide tolerance gene CP4-EPSPS and the insect resistance gene Cry1Ab/Ac were selected as targets taking into account the current status of the most widespread application of insect resistance and herbicide tolerance traits and their stacked traits.Gradient diluted plasmids,transgenic standards,and actual samples were used as templates to conduct sensitivity,specificity,and practicality assays,respectively.The constructed method achieved the visual detection of plasmid at levels as low as 100 copies,demonstrating its high sensitivity.In addition,good applicability to transgenic samples was observed,with no cross-interference between two test lines and no influence from other genes.In conclusion,this strategy achieved the expected purpose of simultaneous detection of the two popular targets in GM crops within 20 min at 37°C in a rapid,equipmentfree field manner,providing a new alternative for rapid screening for transgenic assays in the field.
基金supported by the National Natural Science Foundation of China(31971853)。
文摘The practice of intercropping leguminous and gramineous crops is used for promoting sustainable agriculture,optimizing resource utilization,enhancing biodiversity,and reducing reliance on petroleum products.However,promoting conventional intercropping strategies in modern agriculture can prove challenging.The innovative technology of soybean maize strip intercropping(SMSI)has been proposed as a solution.This system has produced remarkable results in improving domestic soybean and maize production for both food security and sustainable agriculture.In this article,we provide an overview of SMSI and explain how it differs from traditional intercropping.We also discuss the core principles that foster higher yields and the prospects for its future development.
基金supported by the National Natural Science Foundation of China(42003059)State Key Laboratory of Coal Mining and Clean Utilization(2021-CMCU-KF009)the Science Foundation of China University of Petroleum,Beijing(No.2462023YJRC003)。
文摘Refinery sour water primarily originates from the tops of towers in various units and coker condensate,and cannot be discharged directly to a wastewater treatment plant due to high levels of chemical oxygen demand(COD)and organic sulfur contents.Even after the recovery of H_(2)S from the sour water by the stripping process,the effluent still contains a high concentration of dissolved organic sulfur(DOS),which can have a huge bad influence.While chemical composition of dissolved organic matter(DOM)in refinery wastewater has been extensively studied,the investigation of recalcitrant DOS from sour waters remains unclear.In the present study,chemical composition of sour water DOMs(especially DOS)was investigated using fluorescence spectroscopy(excitation-emission matrix,EEM)and mass spectrometry,including gas chromatography-mass spectrometry(GC-MS)and high-resolution Orbitrap MS.The GC-MS and EEM results showed that volatile and low-aromaticity compounds were effectively removed during the stripping process,while compounds with high hydrophilicity and humification degree were found to be more recalcitrant.The Orbitrap MS results showed that weak-polar oxygenated sulfur compounds were easier to be removed than oxygenated compounds.However,the effluent still contained significant amounts of sulfur-containing compounds with multiple sulfur atoms,particularly in the form of highly unsaturated and aromatic compounds.The Orbitrap MS/MS results of CHOS-containing compounds from the effluent indicate that the sulfur atoms may exist as sulfonates,disulfide bonds,thioethers.Understanding the composition and structure of sour water DOS is crucial for the development of effective treatment processes that can target polysulfide compounds and minimize their impact on the environment.
基金supported by the National Natural Science Foundation of China(No.52130408)the Natural Science Foundation of Hunan Province,China(No.2022JJ10081).
文摘The complex producing procedures and high energy-consuming limit the large-scale production and application of advanced high-strength steels(AHSSs).In this study,the direct strip casting(DSC)technology with unique sub-rapid solidification characteristics and cost advantages was applied to the production of low-alloy Si-Mn steel with the help of quenching&partitioning(Q&P)concept to address these issues.Compared this method with the conventional compact strip production(CSP)process,the initial microstructure formed under different solidification conditions and the influence of heat treatment processes on the final mechanical properties were in-vestigated.The results show that the initial structure of the DSC sample is a dual-phase structure composed of fine lath martensite and bainite,while the initial structure of the CSP sample consists of pearlite and ferrite.The volume fraction and carbon content of retained austenite(RA)in DSC samples are usually higher than those in CSP samples after the same Q&P treatment.DSC samples typically demonstrate better comprehensive mechanical properties than the CSP sample.The DSC sample partitioned at 300℃ for 300 s(DSC-Pt300)achieves the best comprehensive mechanical properties,with yield strength(YS)of 1282 MPa,ultimate tensile strength(UTS)of 1501 MPa,total elongation(TE)of 21.5%,and product of strength and elongation(PSE)as high as 32.3 GPa·%.These results indicate that the excellent mechanical properties in low-alloy Si-Mn steel can be obtained through a simple process(DSC-Q&P),which also demonstrates the superiority of DSC technology in manufacturing AHSSs.
基金supported from the National Natural Science Foundation of China(Nos.52204356,52274342,and 52130408)the Natural Science Foundation of Hunan Province,China(Nos.2023JJ40762 and 2021JJ40731)。
文摘The interfacial wettability and heat transfer behavior are crucial in the strip casting of high phosphorus-containing steel.A hightemperature simulation of strip casting was conducted using the droplet solidification technique with the aims to reveal the effects of phosphorus content on interfacial wettability,deposited film,and interfacial heat transfer behavior.Results showed that when the phosphorus content increased from 0.014wt%to 0.406wt%,the mushy zone enlarged,the complete solidification temperature delayed from1518.3 to 1459.4℃,the final contact angle decreased from 118.4°to 102.8°,indicating improved interfacial contact,and the maximum heat flux increased from 6.9 to 9.2 MW/m2.Increasing the phosphorus content from 0.081wt%to 0.406wt%also accelerated the film deposition rate from 1.57 to 1.73μm per test,resulting in a thickened naturally deposited film with increased thermal resistance that advanced the transition point of heat transfer from the fifth experiment to the third experiment.
基金Project supported by the National Key Research and Development Program of China (Grant No.2021YFB2012600)the Shanghai Aerospace Science and Technology Innovation Fund,China (Grant No.SAST-2022-102)。
文摘Counterfeiting of modern banknotes poses a significant challenge,prompting the use of various preventive measures.One such measure is the magnetic anti-counterfeiting strip.However,due to its inherent weak magnetic properties,visualizing its magnetic distribution has been a longstanding challenge.In this work,we introduce an innovative method by using a fiber optic diamond probe,a highly sensitive quantum sensor designed specifically for detecting extremely weak magnetic fields.We employ this probe to achieve high-resolution imaging of the magnetic fields associated with the RMB 50denomination anti-counterfeiting strip.Additionally,we conduct computer simulations by using COMSOL Multiphysics software to deduce the potential geometric characteristics and material composition of the magnetic region within the anti-counterfeiting strip.The findings and method presented in this study hold broader significance,extending the RMB 50 denomination to various denominations of the Chinese currency and other items that employ magnetic anti-counterfeiting strips.These advances have the potential to significantly improve and promote security measures in order to prevent the banknotes from being counterfeited.
文摘An internal defect meter is an instrument to detect the internal inclusion defects of cold-rolled strip steel.The detection accuracy of the equipment can be evaluated based on the similarity of the multiple detection data obtained for the same steel coil.Based on the cosine similarity model and eigenvalue matrix model,a comprehensive evaluation method to calculate the weighted average of similarity is proposed.Results show that the new method is consistent with and can even replace artificial evaluation to realize the automatic evaluation of strip defect detection results.
文摘Many spot defects were found on the surface of a cold-rolled Fe-36%Ni alloy strip produced in a factory,which seriously affected the surface quality of the product.Through metallographic microscopy and scanning electron microscopy analyses,it was found that the spot defects were caused by the residual oxide layer on the surface of the cold-rolled Fe-36%Ni alloy strip after hydrogen annealing.By properly increasing the grinding amount of the blank before cold rolling to remove the oxide layer,the spot defects on the surface of the cold-rolled strip were effectively eliminated,and the surface quality of the product was ensured.
基金financially supported by the National Natural Science Foundation of China(No.52004029)the Fundamental Research Funds for the Central Universities,China(No.FRF-TT-20-06).
文摘Higher requirements for the accuracy of relevant models are put throughout the transformation and upgrade of the iron and steel sector to intelligent production.It has been difficult to meet the needs of the field with the usual prediction model of mechanical properties of hotrolled strip.Insufficient data and difficult parameter adjustment limit deep learning models based on multi-layer networks in practical applications;besides,the limited discrete process parameters used make it impossible to effectively depict the actual strip processing process.In order to solve these problems,this research proposed a new sampling approach for mechanical characteristics input data of hot-rolled strip based on the multi-grained cascade forest(gcForest)framework.According to the characteristics of complex process flow and abnormal sensitivity of process path and parameters to product quality in the hot-rolled strip production,a three-dimensional continuous time series process data sampling method based on time-temperature-deformation was designed.The basic information of strip steel(chemical composition and typical process parameters)is fused with the local process information collected by multi-grained scanning,so that the next link’s input has both local and global features.Furthermore,in the multi-grained scanning structure,a sub sampling scheme with a variable window was designed,so that input data with different dimensions can get output characteristics of the same dimension after passing through the multi-grained scanning structure,allowing the cascade forest structure to be trained normally.Finally,actual production data of three steel grades was used to conduct the experimental evaluation.The results revealed that the gcForest-based mechanical property prediction model outperforms the competition in terms of comprehensive performance,ease of parameter adjustment,and ability to sustain high prediction accuracy with fewer samples.
基金supported by the National Natural Science Foundation of China(52071065)National Key Research and Development Program of China(2016YFB0301201)the Fundamental Research Funds for the Central Universities(N160713001).
文摘As a near-net-shape technology,the twin-roll strip casting(TRC)process can be considered to apply to the fabrication of TiAl alloy sheets.However,the control of the grain distribution is very important in strip casting because the mechanical properties of strips are directly determined by the solidification microstructure.A three-dimensional(3D)cellular automation finite-element(CAFE)model based on ProCAST software was established to simulate the solidification microstructure of Ti-43Al alloy.Then,the influence of casting temperature and the maximum nucleation density(nmax)on the solidification microstructure was investigated in detail.The simulation results provide a good explanation and prediction for the solidification microstructure in the molten pool before leaving the kissing point.Experimental and simulated microstructure show the common texture<001>orientation in the columnar grains zone.Finally,the microstructure evolution of the Ti-43Al alloy was analyzed and the solidification phase transformation path during the TSC process was determined,i.e.,L→L+β→β→β+α→α+γ+β/B2 phase under a faster cooling rate and L→L+β→β→β+α→γ+lamellar(α_(2)+γ)+β/B2 phase under a slower cooling rate.
文摘AIM:To report the outcomes of three cases of corneal perforation managed with simultaneous tectonic Descemet stripping endothelial keratoplasty(t-DSEK)and tectonic Bowman layer transplant(t-BLT)as an alternative to tectonic penetrating keratoplasty(t-PKP).METHODS:Three eyes of three patients receiving simultaneous t-DSEK and t-BLT for corneal perforation were included.The technique for DSEK was modified depending on individual requirements.The t-BLT technique was standardised using an 8 mm graft and fixated with a running suture.Success was measured by the ability of this procedure to close a corneal perforation.RESULTS:All three cases achieved tectonic eye globe restoration and remained stable during the minimum 3-month observation period.Reinterventions were relatively common:2 cases required amniotic membrane transplant for persistent epithelial defects.One case required DSEK rebubbling.One case developed angle closure glaucoma requiring surgical peripheral iridectomy.CONCLUSION:Simultaneous t-DSEK and t-BLT may be a useful strategy for the management of corneal perforation as an alternative management to t-PKP for selected cases.
文摘Bird fauna checklists are important tools in ecology, biology, and conservation planning for scientists, stakeholders, and decision-makers. Despite its small area, the Gaza Strip (365 km<sup>2</sup>) has a relatively large variety of resident and migratory bird fauna. Therefore, the current study aimed to provide an updated checklist of all bird fauna living in or inhabiting the Gaza Strip. Direct field observations using binoculars, continuous visits to zoos, pet stores and biology museums, discussion with bird hunters, follow-up of news and social networking sites, review of scientific publications and photography were the main tools to satisfy the purpose of the study. At least 250 bird species collected from different sources occur in the Gaza Strip and are included in the checklist. This list will not be static, but is inevitably subject to additions and changes in the face of times. The current 250 bird species of the Gaza Strip represent 45.4% of the 551 species of birds living in Palestine. The bird species were found to belong to 21 orders and 61 families. The Passeriformes (passerines) represented the largest order with 96 species of birds (38.4%), followed by the Charadriiformes 54 (21.6%), the Accipitriformes 18 (7.2%), Anseriformes 17 (6.8%) and Pelecaniformes 14 (5.6%), while the other orders represented the remaining percentage (20.4%). With regard to families, the Scolopacidae represented the largest family with 22 species of birds (8.8%), followed by the Anatidae and Accipitridae 17 for each (6.8%), the Muscicapidae 16 (6.4%) and Chariidridae and Fringillidae 11 for each (4.4%), while the other families represented the remaining percentage (62.4%). According to the IUCN regional threat categories, 226 species (90.4%) were Least Concern (LC), 12 (4.8%) were Near Threatened (NT), 6 (2.4%) were Vulnerable (VU), 4 (1.6%) were Endangered (EN) and 2 (0.8%) were Critically Endangered (CR). In conclusion, the study recommends a sustainable control of bird hunting and trafficking in addition to building prestigious centers and museums for studying and documenting birds in the Gaza Strip.
文摘The Mediterranean Sea is home to an interesting biodiversity. The current cumulative and descriptive study aims to enumerate some relatively large marine mammals, reptiles, and fishes that have been spotted, caught, by-caught, or stranded on the coast of the Gaza Strip, Palestine, which extends about 42 km along the Mediterranean Sea. This 20-year study from 2003 to 2022 relied much on frequent field visits, meetings, and discussions with stakeholders, following local media sites and social media pages, and photography. The study recorded at least 26 giants or relatively large marine organisms on the Mediterranean coast of the Gaza Strip, Palestine. Certainly, the coming years may bring other marine organisms of relatively large sizes. Marine mammals included three species of cetaceans with the Fin Whale (Balaenoptera physalus) being the largest mammal and even the largest animal ever recorded in this study. Marine reptiles included three species of sea turtles, the largest of which is the Leatherback Sea Turtle (Dermochelys coriacea), which is in fact the world’s largest sea turtle. The bony fishes were represented by ten species, the largest of which was the Ocean Sunfish (Mola mola), which is the largest bony fish in the world. The cartilaginous fishes included ten species with the largest specimens encountered were the Shortfin Shark (Isurus oxyrinchus), Bluntnose Sixgill Shark (Hexanchus griseus), Scalloped Hammerhead Shark (Sphyrna lewini), and Giant Devil Ray (Mobula mobular). Seabirds were not included in the study. The Alexandria Pompano (Alectis alexandrinus) and the Silver-Cheeked Toadfish (Lagocephalus sceleratus), which are bony fishes, appear to be the relatively smallest marine organisms recorded here. In conclusion, the role of the various parties must be coordinated to ensure the sustainability of human activities and their compatibility with the task of conserving local marine biota, including the gigantic or relatively large ones.
文摘Polysurfacic tori or kideas are three-dimensional objects formed by rotating a regular polygon around a central axis. These toric shapes are referred to as “polysurfacic” because their characteristics, such as the number of sides or surfaces separated by edges, can vary in a non-trivial manner depending on the degree of twisting during the revolution. We use the term “Kideas” to specifically denote these polysurfacic tori, and we represent the number of sides (referred to as “facets”) of the original polygon followed by a point, while the number of facets from which the torus is twisted during its revolution is indicated. We then explore the use of concave regular polygons to generate Kideas. We finally give acceleration for the algorithm for calculating the set of prime numbers.
文摘Artificial cementation is a method commonly used to enhance and improve soil properties. This paper investigates the effect of using different amounts of cement on soil strength parameters and soil bearing capacity, using the finite element method. Experimental tests are conducted on soil samples with different amounts of Portland cement. A 2-D numerical model is created and validated using the numerical modelling software, COMSOL Multiphysics 5.6 software. The study finds that the cohesion, and the angle of the internal friction of the soil samples increase significantly as a result of adding 1%, 2%, and 4% of Portland cement. The results demonstrate that the stresses and strain under the strip footing proposed decrease by 3.24% and 7.42%. Moreover, the maximum displacement also decreases by 1.47% and 2.97%, as a result of adding cements of 2% and 4%. The bearing capacity values obtained are therefore excellent, especially when using the 2% and 4% cement. The increase identified is due to the increased values of the bearing capacity factors. It is concluded that from an economic viewpoint, using 2% cement is the best option.
文摘A miniaturized broadband Wilkinson power divider is proposed. Micro-strip branch lines are introduced to replace multiple resistors used in multi-stage Wilkinson power dividers to increase the bandwidth of single-stage Wilkinson power dividers. To demonstrate its performance, an improved single-stage Wilkinson power divider with four micro-strip branch lines was designed. Simulated results show that the insert loss is better than 3.2 dB, the input return loss, output return loss, and isolation are better than 15 dB respectively, across a 76% bandwidth from 18 to 40 GHz. .
基金Supported by the National Natural Science Foundation of China under Grant No.60173039(国家自然科学基金)the Special Foundation of 985 Project of SUN YAT-SEN University of China (中山大学985工程专项资金)
