The supported catalysts for propylene polymerization were prepared by milling Mg (OEt)_2 with EB (ethylbenzoate) and treating with TiCl_4 solution. When TiCl_4/(Mg(OEt)_2/EB) (mol.) ratio was increased, decrease in co...The supported catalysts for propylene polymerization were prepared by milling Mg (OEt)_2 with EB (ethylbenzoate) and treating with TiCl_4 solution. When TiCl_4/(Mg(OEt)_2/EB) (mol.) ratio was increased, decrease in contents of-OEt and Ti of the catalysts was observed, while the content of EB increased. It is proved by analyses of IR, X-ray and XPS that during co-milling Mg(OEt)_2 with EB no reactions have taken place. But after treatment with TiCl_4 solution, Mg(OEt)_2 converts into MgCl_2 and EB coordinates on the resulting MgCl_2 carrier, a surface complex forms.The activity of catalysts,isotacticity and vicosimetric molecular weight of polypropylene increase with the decrease of the content of ethoxyl group. The kinetic curves of propene polymerization obtained with present catalysts system display decay curves. It is found from the triad tacticity calculated from the expanded spectra of methyl carbon region that, ethoxyl group in catalyst has an effect on the configuration of polymer chain.展开更多
Developing the alternative supported noble metal catalysts with low cost,high catalytic efficiency,and good resistance toward carbon dioxide and water vapor is critically demanded for the oxidative removal of volatile...Developing the alternative supported noble metal catalysts with low cost,high catalytic efficiency,and good resistance toward carbon dioxide and water vapor is critically demanded for the oxidative removal of volatile organic compounds(VOCs).In this work,we prepared the mesoporous chromia-supported bimetallic Co and Ni single-atom(Co_(1)Ni_(1)/meso-Cr_(2)O_(3))and bimetallic Co and Ni nanoparticle(Co_(NP)Ni_(NP)/mesoCr_(2)O_(3))catalysts adopting the one-pot polyvinyl pyrrolidone(PVP)-and polyvinyl alcohol(PVA)-protecting approaches,respectively.The results indicate that the Co_(1)Ni_(1)/meso-Cr_(2)O_(3)catalyst exhibited the best catalytic activity for n-hexane(C_(6)H_(14))combustion(T_(50%)and T_(90%)were 239 and 263℃ at a space velocity of 40,000 mL g^(-1)h^(-1);apparent activation energy and specific reaction rate at 260℃ were 54.7 kJ mol^(-1)and 4.3×10^(-7)mol g^(-1)_(cat)s^(-1),respectively),which was associated with its higher(Cr^(5+)+Cr^(6+))amount,large n-hexane adsorption capacity,and good lattice oxygen mobility that could enhance the deep oxidation of n-hexane,in which Ni_(1) was beneficial for the enhancements in surface lattice oxygen mobility and low-temperature reducibility,while Co_(1) preferred to generate higher contents of the high-valence states of chromium and surface oxygen species as well as adsorption and activation of n-hexane.n-Hexane combustion takes place via the Mars van Krevelen(MvK)mechanism,and its reaction pathways are as follows:n-hexane→olefins or 3-hexyl hydroperoxide→3-hexanone,2-hexanone or 2,5-dimethyltetrahydrofuran→2-methyloxirane or 2-ethyl-oxetane→acrylic acid→CO_x→CO_(2)and H_(2)O.展开更多
Catalyst–support interaction plays a crucial role in improving the catalytic activity of oxygen evolution reaction(OER).Here we modulate the catalyst–support interaction in polyaniline-supported Ni_(3)Fe oxide(Ni_(3...Catalyst–support interaction plays a crucial role in improving the catalytic activity of oxygen evolution reaction(OER).Here we modulate the catalyst–support interaction in polyaniline-supported Ni_(3)Fe oxide(Ni_(3)Fe oxide/PANI)with a robust hetero-interface,which significantly improves oxygen evolution activities with an overpotential of 270 mV at 10 mA cm^(-2)and specific activity of 2.08 mA cm_(ECSA)^(-2)at overpotential of 300 mV,3.84-fold that of Ni_(3)Fe oxide.It is revealed that the catalyst–support interaction between Ni_(3)Fe oxide and PANI support enhances the Ni–O covalency via the interfacial Ni–N bond,thus promoting the charge and mass transfer on Ni_(3)Fe oxide.Considering the excellent activity and stability,rechargeable Zn-air batteries with optimum Ni_(3)Fe oxide/PANI are assembled,delivering a low charge voltage of 1.95 V to cycle for 400 h at 10 mA cm^(-2).The regulation of the effect of catalyst–support interaction on catalytic activity provides new possibilities for the future design of highly efficient OER catalysts.展开更多
Supported metal catalysts,particularly for precious metals,have gained increasing attention in green synthetic chemistry.They can make metal-catalyzed organic synthesis more sustainable and economical due to easy sepa...Supported metal catalysts,particularly for precious metals,have gained increasing attention in green synthetic chemistry.They can make metal-catalyzed organic synthesis more sustainable and economical due to easy separation of product with less metal residue,as well as reusability of the high-cost catalysts.Although great effort has been spent,the precise catalytic mechanism of supported metal-catalyzed reactions has not been clearly elucidated and the development of efficient and stable recyclable catalysts remains challenging.This highlight reveals a“molecular fence”metal stabilization strategy and discloses the metal evolution in Pd-catalyzed C-C bond formation reactions using Nheterocyclic carbene(NHC)-functionalized hypercrosslinked polymer support,wherein the polymeric skeleton isolates or confines the metal species involved in the catalytic reactions,and NHC captures free low-valent metal species in solution and stabilizes them on the support via strong metal-support coordination interaction.This strategy creates a novel route for the development of supported metal catalysts with high stability and provides insights into the reaction mechanism of heterogeneous catalysis.展开更多
Enhancing the stability of supported noble metal catalysts emerges is a major challenge in both science and industry.Herein,a heterogeneous Pd catalyst(Pd/NCF)was prepared by supporting Pd ultrafine metal nanoparticle...Enhancing the stability of supported noble metal catalysts emerges is a major challenge in both science and industry.Herein,a heterogeneous Pd catalyst(Pd/NCF)was prepared by supporting Pd ultrafine metal nanoparticles(NPs)on nitrogen-doped carbon;synthesized by using F127 as a stabilizer,as well as chitosan as a carbon and nitrogen source.The Pd/NCF catalyst was efficient and recyclable for oxidative carbonylation of phenol to diphenyl carbonate,exhibiting higher stability than Pd/NC prepared without F127 addition.The hydrogen bond between chitosan(CTS)and F127 was enhanced by F127,which anchored the N in the free amino group,increasing the N content of the carbon material and ensuring that the support could provide sufficient N sites for the deposition of Pd NPs.This process helped to improve metal dispersion.The increased metal-support interaction,which limits the leaching and coarsening of Pd NPs,improves the stability of the Pd/NCF catalyst.Furthermore,density functional theory calculations indicated that pyridine N stabilized the Pd^(2+)species,significantly inhibiting the loss of Pd^(2+)in Pd/NCF during the reaction process.This work provides a promising avenue towards enhancing the stability of nitrogen-doped carbon-supported metal catalysts.展开更多
Most of volatile organic compounds （VOCs） are harmful to the atmosphere and human health. Cata‐lytic combustion is an effective way to eliminate VOCs. The key issue is the availability of high per‐formance catalys...Most of volatile organic compounds （VOCs） are harmful to the atmosphere and human health. Cata‐lytic combustion is an effective way to eliminate VOCs. The key issue is the availability of high per‐formance catalysts. Many catalysts including transition metal oxides, mixed metal oxides, and sup‐ported noble metals have been developed. Among these catalysts, the porous ones attract much attention. In this review, we focus on recent advances in the synthesis of ordered mesoporous and macroporous transition metal oxides, perovskites, and supported noble metal catalysts and their catalytic oxidation of VOCs. The porous catalysts outperformed their bulk counterparts. This excel‐lent catalytic performance was due to their high surface areas, high concentration of adsorbed oxy‐gen species, low temperature reducibility, strong interaction between noble metal and support and highly dispersed noble metal nanoparticles and unique porous structures. Catalytic oxidation of carbon monoxide over typical catalysts was also discussed. We made conclusive remarks and pro‐posed future work for the removal of VOCs.展开更多
Nickel and nickel-ceria catalysts supported on high surface area silica, with 6 wt% Ni and 20 wt% CeO2 were prepared by microwave assisted(co) precipitation method. The catalysts were investigated by XRD,TPR and XPS a...Nickel and nickel-ceria catalysts supported on high surface area silica, with 6 wt% Ni and 20 wt% CeO2 were prepared by microwave assisted(co) precipitation method. The catalysts were investigated by XRD,TPR and XPS analyses and they were tested in partial oxidation of methane(CPO). The catalytic reaction was carried out at atmospheric pressure in a temperature range of 400–800℃ with a feed gas mixture containing methane and oxygen in a molecular ratio CH4/O2=2. The Ni catalyst exhibited 60% methane conversion with 60% selectivity to CO already at 500℃. On the contrary, the Ni–Ce catalyst was inert to CPO up to 700℃. Moreover, the former catalyst reproduced its activity at the descending temperatures maintaining a good stability at 600℃, over a reaction time of 80 h, whereas the latter one completely deactivated. Test of CH4 temperature programmed surface reaction(CH4-TPSR) revealed a higher methane activation temperature(> 100℃) for the Ni–Ce catalyst as compared to the Ni one. Noticeable improvement of the ceria containing catalyst occurred when the reaction test started at a temperature higher than the methane decomposition temperature. In this case, the sample achieved the same catalytic behavior of the Ni catalyst. As confirmed by XPS analyses, the distinct electronic state of the supported nickel was responsible for the differences in catalytic behavior.展开更多
The simultaneous removal of SO_(2),NO_(x)and Hg^(0)from industrial exhaust flue gas has drawn worldwide attention in recent years.A particularly attractive technique is selective catalytic reduction,which effectively ...The simultaneous removal of SO_(2),NO_(x)and Hg^(0)from industrial exhaust flue gas has drawn worldwide attention in recent years.A particularly attractive technique is selective catalytic reduction,which effectively removes SO_(2),NO_(x)and Hg^(0)at low temperatures.This paper first reviews the simultaneous removal of SO_(2),NO_(x)and Hg^(0)by unsupported and supported catalysts.It then describes and compares the research progress of various carriers,eg.,carbon-based materials,metal oxides,silica,molecular sieves,metal-organic frameworks,and pillared interlayered clays,in the simultaneous removal of SO_(2),NO_(x)and Hg^(0).The effects of flue-gas components(such as O_(2),NH3,HCl,H2 O,SO_(2),NO and Hg^(0))on the removal of SO_(2),NOx,and Hg^(0)are discussed comprehensively and systematically.After summarizing the pollutantremoval mechanism,the review discusses future developments in the simultaneous removal of SO_(2),NOx and Hg^(0)by catalysts.展开更多
8-Aminoquinoline nickel dichloride and bis(cyclopentadienyl)zirconium dichloride (Cp_2ZrCl_2) were supportedsimultaneously on silica to produce branched polyethylene successfully by combined polymerization. The suppor...8-Aminoquinoline nickel dichloride and bis(cyclopentadienyl)zirconium dichloride (Cp_2ZrCl_2) were supportedsimultaneously on silica to produce branched polyethylene successfully by combined polymerization. The supportedpolymerization results showed that the molecular weight of polyethylene increased while the molecular weight distributionbecame wider and the molecular chains of oligomers remaning in the final solution became shorter as compared to theoligomers obtained in polymerization processes with pure 8-aminoquinoline nickel dichloride catalysis, as well as theCp_2ZrCl_2 and nickel combination system. With decreasing amount of Ni catalyst in the supported catalyst, the molecular chains of oligomers in the resulting solution became shorter, while α-olefin selectivity increased.展开更多
A series of Pd catalysts were prepared on different supports（Fe2O3,SiO2,ZnO,MgO,Al2O3,carbon,and Amberlyst-45） and used in the selective hydrogenation of phenol to cyclohexanone in water.The Amberlyst-45 supported P...A series of Pd catalysts were prepared on different supports（Fe2O3,SiO2,ZnO,MgO,Al2O3,carbon,and Amberlyst-45） and used in the selective hydrogenation of phenol to cyclohexanone in water.The Amberlyst-45 supported Pd catalyst（Pd/A-45） was highly active and selective under mild conditions（40-100 ℃,0.2-1 MPa）,giving a selectivity of cyclohexanone higher than 89%even at complete conversion of phenol.Experiments with different Pd loadings（or different particle sizes） confirmed that the formation of cyclohexanone was a structure sensitive reaction,and Pd particles of12-14 nm on Amberlyst-45 gave better selectivity and stability.展开更多
The hydrogenation of m-dinitrobenzene to m-phenylenediamine in liquid phase was studied with the nickel catalysts supported on SiO2, TiO2, γ-Al2O3, MgO and diatomite carders. Based on the experiments of X-ray diffrac...The hydrogenation of m-dinitrobenzene to m-phenylenediamine in liquid phase was studied with the nickel catalysts supported on SiO2, TiO2, γ-Al2O3, MgO and diatomite carders. Based on the experiments of X-ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS）, temperature-programmed reduction （TPR）, temperature-programmed desorption of hydrogen （H2-TPD） and activity evaluation, the physico-chemical and catalytic properties of the catalysts were investigated. Among the catalysts tested, the SiO2 supported nickel catalyst showed the highest activity and selectivity towards m-phenylenediamine, over which 97.3% m-dinitrobenzene conversion and 95.1% m-phenylenediamine yield were obtained at 373K under hydrogen pressure of 2.6MPa after reaction for 6 h when using ethanol as solvent. Although TiO2 and diatomite supported nickel catalysts also presented high activity, they had lower selectivity towards m-phenylenediamine. As for γ-Al2O3 and MgO supported catalysts were almost inactive for the object reaction. It was shown that both the activity and selectivity of the catalysts were strongly depended on the interaction between nickel and the support. The higher activities of Ni/SiO2, Ni/TiO2 and Ni/diatomite could be attributed to the weaker metal-support interaction, on which Ni species presented as crystallized Ni metal particles. On the other hand, there existed strong metal-support interaction in Ni/MgO and Ni γ-Al2O3, which causes these catalysts more difficult to be reduced and the availability of Ni active sites decreased, resulting in their low catalytic activity.展开更多
A series of perovskite type oxides and supported Ag catalysts were prepared, and characterized by X ray diffraction (XRD) and X ray photoelectron spectroscopy (XPS). The catalytic activities of the catalyst...A series of perovskite type oxides and supported Ag catalysts were prepared, and characterized by X ray diffraction (XRD) and X ray photoelectron spectroscopy (XPS). The catalytic activities of the catalysts as well as influencing factors on catalytic activity have been investigated for the simultaneous removal of NOx and diesel soot particulate. An increase in catalytic activity for the selective reduction of NOx was observed with Ag addition in these perovskite oxides, especially with 5% Ag loading. This catalyst could be a promising candidate of catalytic material for the simultaneous elimination of NOx and diesel soot.展开更多
To investigate how the physicochemical properties and NH3‐selective catalytic reduction(NH3‐SCR)performance of supported ceria‐based catalysts are influenced as a function of support type,a series of CeO2/SiO2,CeO2...To investigate how the physicochemical properties and NH3‐selective catalytic reduction(NH3‐SCR)performance of supported ceria‐based catalysts are influenced as a function of support type,a series of CeO2/SiO2,CeO2/γ‐Al2O3,CeO2/ZrO2,and CeO2/TiO2catalysts were prepared.The physicochemical properties were probed by means of X‐ray diffraction,Raman spectroscopy,Brunauer‐Emmett‐Teller surface area measurements,X‐ray photoelectron spectroscopy,H2‐temperature programmed reduction,and NH3‐temperature programmed desorption.Furthermore,the supported ceria‐based catalysts'catalytic performance and H2O+SO2tolerance were evaluated by the NH3‐SCR model reaction.The results indicate that out of the supported ceria‐based catalysts studied,the CeO2/γ‐Al2O3catalyst exhibits the highest catalytic activity as a result of having a high relative Ce3+/Ce4+ratio,optimum reduction behavior,and the largest total acid site concentration.Finally,the CeO2/γ‐Al2O3catalyst also presents excellent H2O+SO2tolerance during the NH3‐SCR process.展开更多
Sodium-treated sepiolite(Na Sep)-supported transition metal catalysts(TM/Na Sep;TM = Cu, Fe, Ni, Mn, and Co) were synthesized via a rotary evaporation method. Physicochemical properties of the as-synthesized samples w...Sodium-treated sepiolite(Na Sep)-supported transition metal catalysts(TM/Na Sep;TM = Cu, Fe, Ni, Mn, and Co) were synthesized via a rotary evaporation method. Physicochemical properties of the as-synthesized samples were characterized by means of various techniques, and their catalytic activities for HCHO(0.2%) oxidation were evaluated. Among the samples, Cu/Na Sep exhibited superior performance, and complete HCHO conversion was achieved at 100 ℃(GHSV = 240000 m L/(g·h)). Additionally, the sample retained good catalytic activity during a 42 h stability test. A number of factors, including elevated acidity, the abundance of oxygen species, and favorable low-temperature reducibility, were responsible for the excellent catalytic activity of Cu/Na Sep. According to the results of the in-situ DRIFTS characterization, the HCHO oxidation mechanism was as follows:(i) HCHO was rapidly decomposed into dioxymethylene(DOM) species on the Cu/Na Sep surface;(ii) DOM was then immediately converted to formate species;(iii) the resultant formate species were further oxidized to carbonates;(iv) the carbonate species were eventually converted to CO2 and H2O.展开更多
Catalyst support is extremely important for future fuel cell devices.In this work,we developed doubleshelled C/TiO2(DSCT)hollow spheres as an excellent catalyst support via a template-directed method.The combination o...Catalyst support is extremely important for future fuel cell devices.In this work,we developed doubleshelled C/TiO2(DSCT)hollow spheres as an excellent catalyst support via a template-directed method.The combination of hollow structure,TiO2 shell and carbon layer results in excellent electron conductivity,electrocatalytic activity,and chemical stability.These uniformed DSCT hollow spheres are used as catalyst support to synthesize Pt/DSCT hollow spheres electrocatalyst.The resulting Pt/DSCT hollow spheres exhibited high catalytic performance with a current density of 462 mA mg^-1 for methanol oxidation reaction,which is 2.52 times higher than that of the commercial Pt/C.Furthermore,the increased tolerance to carbonaceous poisoning with a higher If/Ibratio and a better long-term stability in acid media suggests that the DSCT hollow sphere is a promising C/TiO2-based catalyst support for direct methanol fuel cells applications.展开更多
Polyethylene (PE) grafting 4-vinylpyridine copolymers has been produced as powders of different rushes by theirradiation method. After treatment with methylaluminoxane (MAO), the copolymers were used as supports for C...Polyethylene (PE) grafting 4-vinylpyridine copolymers has been produced as powders of different rushes by theirradiation method. After treatment with methylaluminoxane (MAO), the copolymers were used as supports for Cp_2ZrCl_2catalyst Results of X-ray photoelectron spectroscopy, Fourier transforms infrared spectroscopy, ultraviolet spectroscopy andscanning electron microscope measurements show that the catalytic sites have been linked through MAO on the PE-graft-4-vinylpyridine (PEVP). The percentages of grafting 4-vinylpyridine and supported Cp_2ZrCl_2 depend on the size ofpolyethylene powder. The smaller the polyethylene powder, the more percent of 4-vinylpyridine groups and Cp_2ZrCl_2 existon the polyethylene chains, and the PEVP-supported catalyst has a relatively high activity for ethylene polymerization.展开更多
Direct cost-effective conversion of abundant methane to high value-added oxygenates(methanol,formic acid,acetic acid,etc.)under mild conditions is prospective for optimizing the structure of energy resources.However,t...Direct cost-effective conversion of abundant methane to high value-added oxygenates(methanol,formic acid,acetic acid,etc.)under mild conditions is prospective for optimizing the structure of energy resources.However,the CAH bond of products is more reactive than that of high thermodynamic stable methane.Exploring an appropriate approach to eliminate the‘‘seesaw effect"between methane conversion and oxygenate selectivity is significant.In this review,we briefly summarize the research progress in the past decade on low-temperature direct conversion of methane to oxygenates in gas-solid-liquid phase over various transition metal(Fe,Cu,Rh,Pd,Au Pd,etc.)based nanoparticle or single-atom catalyst.Furthermore,the prospects of catalyst design and catalysis process are also discussed.展开更多
An account of recent work on supported single‐atom catalyst design is given here for reactions as diverse as the low‐temperature water‐gas shift,methanol steam reforming,selective ethanol dehydrogenation,and select...An account of recent work on supported single‐atom catalyst design is given here for reactions as diverse as the low‐temperature water‐gas shift,methanol steam reforming,selective ethanol dehydrogenation,and selective hydrogenation of alkynes and dienes.It is of fundamental interest to investigate the intrinsic activity and selectivity of the active metal atom site and compare them to the properties of the corresponding metal nanoparticles and sub‐nm clusters.It is also important to understand what constitutes a stable active metal atom site in the various reaction environments,and maximize their loadings to allow us to design robust catalysts for industrial applications.Combined activity and stability studies,ideally following the evolution of the active site as a function of catalyst treatment in real time are recommended.Advanced characterization methods with atomic resolution will play a key role here and will be used to guide the design of new catalysts.展开更多
An ultrasound-assisted heterogeneous catalytic oxidation process was applied to eliminate sulfur from commercial diesel fuel oil.The studied variables were catalyst concentration,type of catalyst(homogeneous or hetero...An ultrasound-assisted heterogeneous catalytic oxidation process was applied to eliminate sulfur from commercial diesel fuel oil.The studied variables were catalyst concentration,type of catalyst(homogeneous or heterogeneous),oxidizing agent concentration,and the application of ultrasound energy.Supported catalysts were prepared by impregnation of coal fly ash with an iron(Ⅱ)sulfate aqueous solution using ultrasound energy.After drying,the catalyst was calcined at 500℃for 4 h.The oxidizing agent was hydrogen peroxide.Ultrasound energy was applied with a frequency of 47 kHz and an intensity of 147 W.Ethanol was employed for extracting the oxidized compounds from the hydrocarbon mixture.Coal fly ash and ethanol were used with the purpose of applying low-cost raw materials in chemical processes.It was found that under the studied conditions,increasing oxidizing agent concentration and the application of ultrasound energy can enhance the sulfur removal from commercial diesel fuel oil.Catalyst concentration did not play a significant role in the process.Similar results were obtained using homogeneous or heterogeneous catalyst,which is important since the heterogeneous catalyst could be recovered,reactivated,and used in many cycles.展开更多
Catalyst supports have very important effects on catalyst performance.A novel expanded multilayered vermiculite（EML-VMT） is successfully used as the catalyst support for the acetylene hydrochlorination.By mixing car...Catalyst supports have very important effects on catalyst performance.A novel expanded multilayered vermiculite（EML-VMT） is successfully used as the catalyst support for the acetylene hydrochlorination.By mixing carbon on the surface of EML-VMT[i.e.,EML-VMT-C）,the HgCl2/EML-VMT-C achieved a high acetylene conversion of 97.3%,a vinyl chloride selectivity of 100%and a turn over frequency（TOF） value of 8.83 × 10^-3s^-1 at a temperature of 140 C,an acetylene gas hourly space velocity（GHSV） of 108 h^-1,and a feed volume ratio V（HC1）/V（C2H2） of 1.15.Moreover,the HgCl2/EML-VMT-C shows good stability.The EML-VMT also shows potential in the preparation of other EML-VMT-supported catalysts.展开更多
文摘The supported catalysts for propylene polymerization were prepared by milling Mg (OEt)_2 with EB (ethylbenzoate) and treating with TiCl_4 solution. When TiCl_4/(Mg(OEt)_2/EB) (mol.) ratio was increased, decrease in contents of-OEt and Ti of the catalysts was observed, while the content of EB increased. It is proved by analyses of IR, X-ray and XPS that during co-milling Mg(OEt)_2 with EB no reactions have taken place. But after treatment with TiCl_4 solution, Mg(OEt)_2 converts into MgCl_2 and EB coordinates on the resulting MgCl_2 carrier, a surface complex forms.The activity of catalysts,isotacticity and vicosimetric molecular weight of polypropylene increase with the decrease of the content of ethoxyl group. The kinetic curves of propene polymerization obtained with present catalysts system display decay curves. It is found from the triad tacticity calculated from the expanded spectra of methyl carbon region that, ethoxyl group in catalyst has an effect on the configuration of polymer chain.
基金supported by the National Natural Science Committee of China-Liaoning Provincial People's Government Joint Fund(U1908204)National Natural Science Foundation of China(21876006,21976009,and 21961160743)+2 种基金Foundation on the Creative Research Team Construction Promotion Project of Beijing Municipal Institutions(IDHT20190503)Natural Science Foundation of Beijing Municipal Commission of Education(KM201710005004)Development Program for the Youth Outstanding-Notch Talent of Beijing Municipal Commission of Education(CIT&TCD201904019)。
文摘Developing the alternative supported noble metal catalysts with low cost,high catalytic efficiency,and good resistance toward carbon dioxide and water vapor is critically demanded for the oxidative removal of volatile organic compounds(VOCs).In this work,we prepared the mesoporous chromia-supported bimetallic Co and Ni single-atom(Co_(1)Ni_(1)/meso-Cr_(2)O_(3))and bimetallic Co and Ni nanoparticle(Co_(NP)Ni_(NP)/mesoCr_(2)O_(3))catalysts adopting the one-pot polyvinyl pyrrolidone(PVP)-and polyvinyl alcohol(PVA)-protecting approaches,respectively.The results indicate that the Co_(1)Ni_(1)/meso-Cr_(2)O_(3)catalyst exhibited the best catalytic activity for n-hexane(C_(6)H_(14))combustion(T_(50%)and T_(90%)were 239 and 263℃ at a space velocity of 40,000 mL g^(-1)h^(-1);apparent activation energy and specific reaction rate at 260℃ were 54.7 kJ mol^(-1)and 4.3×10^(-7)mol g^(-1)_(cat)s^(-1),respectively),which was associated with its higher(Cr^(5+)+Cr^(6+))amount,large n-hexane adsorption capacity,and good lattice oxygen mobility that could enhance the deep oxidation of n-hexane,in which Ni_(1) was beneficial for the enhancements in surface lattice oxygen mobility and low-temperature reducibility,while Co_(1) preferred to generate higher contents of the high-valence states of chromium and surface oxygen species as well as adsorption and activation of n-hexane.n-Hexane combustion takes place via the Mars van Krevelen(MvK)mechanism,and its reaction pathways are as follows:n-hexane→olefins or 3-hexyl hydroperoxide→3-hexanone,2-hexanone or 2,5-dimethyltetrahydrofuran→2-methyloxirane or 2-ethyl-oxetane→acrylic acid→CO_x→CO_(2)and H_(2)O.
基金Research Institute for Smart Energy(CDB2)the grant from the Research Institute for Advanced Manufacturing(CD8Z)+4 种基金the grant from the Carbon Neutrality Funding Scheme(WZ2R)at The Hong Kong Polytechnic Universitysupport from the Hong Kong Polytechnic University(CD9B,CDBZ and WZ4Q)the National Natural Science Foundation of China(22205187)Shenzhen Municipal Science and Technology Innovation Commission(JCYJ20230807140402006)Start-up Foundation for Introducing Talent of NUIST and Natural Science Foundation of Jiangsu Province of China(BK20230426).
文摘Catalyst–support interaction plays a crucial role in improving the catalytic activity of oxygen evolution reaction(OER).Here we modulate the catalyst–support interaction in polyaniline-supported Ni_(3)Fe oxide(Ni_(3)Fe oxide/PANI)with a robust hetero-interface,which significantly improves oxygen evolution activities with an overpotential of 270 mV at 10 mA cm^(-2)and specific activity of 2.08 mA cm_(ECSA)^(-2)at overpotential of 300 mV,3.84-fold that of Ni_(3)Fe oxide.It is revealed that the catalyst–support interaction between Ni_(3)Fe oxide and PANI support enhances the Ni–O covalency via the interfacial Ni–N bond,thus promoting the charge and mass transfer on Ni_(3)Fe oxide.Considering the excellent activity and stability,rechargeable Zn-air batteries with optimum Ni_(3)Fe oxide/PANI are assembled,delivering a low charge voltage of 1.95 V to cycle for 400 h at 10 mA cm^(-2).The regulation of the effect of catalyst–support interaction on catalytic activity provides new possibilities for the future design of highly efficient OER catalysts.
基金support of the Start-up Research Fund of Dongguan University of Technology(KCYKYQD2017015).
文摘Supported metal catalysts,particularly for precious metals,have gained increasing attention in green synthetic chemistry.They can make metal-catalyzed organic synthesis more sustainable and economical due to easy separation of product with less metal residue,as well as reusability of the high-cost catalysts.Although great effort has been spent,the precise catalytic mechanism of supported metal-catalyzed reactions has not been clearly elucidated and the development of efficient and stable recyclable catalysts remains challenging.This highlight reveals a“molecular fence”metal stabilization strategy and discloses the metal evolution in Pd-catalyzed C-C bond formation reactions using Nheterocyclic carbene(NHC)-functionalized hypercrosslinked polymer support,wherein the polymeric skeleton isolates or confines the metal species involved in the catalytic reactions,and NHC captures free low-valent metal species in solution and stabilizes them on the support via strong metal-support coordination interaction.This strategy creates a novel route for the development of supported metal catalysts with high stability and provides insights into the reaction mechanism of heterogeneous catalysis.
基金support by the National Natural Science Foundation of China(U21A20306,U20A20152)Natural Science Foundation of Hebei Province(B2022202077).
文摘Enhancing the stability of supported noble metal catalysts emerges is a major challenge in both science and industry.Herein,a heterogeneous Pd catalyst(Pd/NCF)was prepared by supporting Pd ultrafine metal nanoparticles(NPs)on nitrogen-doped carbon;synthesized by using F127 as a stabilizer,as well as chitosan as a carbon and nitrogen source.The Pd/NCF catalyst was efficient and recyclable for oxidative carbonylation of phenol to diphenyl carbonate,exhibiting higher stability than Pd/NC prepared without F127 addition.The hydrogen bond between chitosan(CTS)and F127 was enhanced by F127,which anchored the N in the free amino group,increasing the N content of the carbon material and ensuring that the support could provide sufficient N sites for the deposition of Pd NPs.This process helped to improve metal dispersion.The increased metal-support interaction,which limits the leaching and coarsening of Pd NPs,improves the stability of the Pd/NCF catalyst.Furthermore,density functional theory calculations indicated that pyridine N stabilized the Pd^(2+)species,significantly inhibiting the loss of Pd^(2+)in Pd/NCF during the reaction process.This work provides a promising avenue towards enhancing the stability of nitrogen-doped carbon-supported metal catalysts.
基金supported by the National High Technology Research and Development Program (863 Program,2015AA034603)the National Natural Science Foundation of China (21377008,201077007,20973017)+1 种基金Foundation on the Creative Research Team Construction Promotion Project of Beijing Municipal InstitutionsScientific Research Base Construction-Science and Technology Creation Platform National Materials Research Base Construction~~
文摘Most of volatile organic compounds （VOCs） are harmful to the atmosphere and human health. Cata‐lytic combustion is an effective way to eliminate VOCs. The key issue is the availability of high per‐formance catalysts. Many catalysts including transition metal oxides, mixed metal oxides, and sup‐ported noble metals have been developed. Among these catalysts, the porous ones attract much attention. In this review, we focus on recent advances in the synthesis of ordered mesoporous and macroporous transition metal oxides, perovskites, and supported noble metal catalysts and their catalytic oxidation of VOCs. The porous catalysts outperformed their bulk counterparts. This excel‐lent catalytic performance was due to their high surface areas, high concentration of adsorbed oxy‐gen species, low temperature reducibility, strong interaction between noble metal and support and highly dispersed noble metal nanoparticles and unique porous structures. Catalytic oxidation of carbon monoxide over typical catalysts was also discussed. We made conclusive remarks and pro‐posed future work for the removal of VOCs.
基金The Executive Programme for Cooperation between Italy and India (Prot.No.MAE01054762017)。
文摘Nickel and nickel-ceria catalysts supported on high surface area silica, with 6 wt% Ni and 20 wt% CeO2 were prepared by microwave assisted(co) precipitation method. The catalysts were investigated by XRD,TPR and XPS analyses and they were tested in partial oxidation of methane(CPO). The catalytic reaction was carried out at atmospheric pressure in a temperature range of 400–800℃ with a feed gas mixture containing methane and oxygen in a molecular ratio CH4/O2=2. The Ni catalyst exhibited 60% methane conversion with 60% selectivity to CO already at 500℃. On the contrary, the Ni–Ce catalyst was inert to CPO up to 700℃. Moreover, the former catalyst reproduced its activity at the descending temperatures maintaining a good stability at 600℃, over a reaction time of 80 h, whereas the latter one completely deactivated. Test of CH4 temperature programmed surface reaction(CH4-TPSR) revealed a higher methane activation temperature(> 100℃) for the Ni–Ce catalyst as compared to the Ni one. Noticeable improvement of the ceria containing catalyst occurred when the reaction test started at a temperature higher than the methane decomposition temperature. In this case, the sample achieved the same catalytic behavior of the Ni catalyst. As confirmed by XPS analyses, the distinct electronic state of the supported nickel was responsible for the differences in catalytic behavior.
基金supported by the National Natural Science Foundation of China(Nos.52000093,51968034,41807373 and21667015)National Key R&D Program of China(No.2018YFC0213400)+1 种基金China Postdoctoral Science Foundation(Nos.2020T130271,2019M663911XB)Open Fund of National Engineering Laboratory for Mobile Source Emission Control Technology(No.NELMS2019B03)。
文摘The simultaneous removal of SO_(2),NO_(x)and Hg^(0)from industrial exhaust flue gas has drawn worldwide attention in recent years.A particularly attractive technique is selective catalytic reduction,which effectively removes SO_(2),NO_(x)and Hg^(0)at low temperatures.This paper first reviews the simultaneous removal of SO_(2),NO_(x)and Hg^(0)by unsupported and supported catalysts.It then describes and compares the research progress of various carriers,eg.,carbon-based materials,metal oxides,silica,molecular sieves,metal-organic frameworks,and pillared interlayered clays,in the simultaneous removal of SO_(2),NO_(x)and Hg^(0).The effects of flue-gas components(such as O_(2),NH3,HCl,H2 O,SO_(2),NO and Hg^(0))on the removal of SO_(2),NOx,and Hg^(0)are discussed comprehensively and systematically.After summarizing the pollutantremoval mechanism,the review discusses future developments in the simultaneous removal of SO_(2),NOx and Hg^(0)by catalysts.
基金This work was also supported by the Core Research for Engineering Innovation KGCX2-203 of the Chinese Academy of Sciences, National Natural Science Foundation of China (No. 20272062) and the "One Hundred Talents" Fund foWen-Hua Sun.
文摘8-Aminoquinoline nickel dichloride and bis(cyclopentadienyl)zirconium dichloride (Cp_2ZrCl_2) were supportedsimultaneously on silica to produce branched polyethylene successfully by combined polymerization. The supportedpolymerization results showed that the molecular weight of polyethylene increased while the molecular weight distributionbecame wider and the molecular chains of oligomers remaning in the final solution became shorter as compared to theoligomers obtained in polymerization processes with pure 8-aminoquinoline nickel dichloride catalysis, as well as theCp_2ZrCl_2 and nickel combination system. With decreasing amount of Ni catalyst in the supported catalyst, the molecular chains of oligomers in the resulting solution became shorter, while α-olefin selectivity increased.
基金supported by the National Natural Science Foundation of China(21473155,21273198,21073159)the Natural Science Foundation of Zhejiang Province(LZ12B03001)~~
文摘A series of Pd catalysts were prepared on different supports（Fe2O3,SiO2,ZnO,MgO,Al2O3,carbon,and Amberlyst-45） and used in the selective hydrogenation of phenol to cyclohexanone in water.The Amberlyst-45 supported Pd catalyst（Pd/A-45） was highly active and selective under mild conditions（40-100 ℃,0.2-1 MPa）,giving a selectivity of cyclohexanone higher than 89%even at complete conversion of phenol.Experiments with different Pd loadings（or different particle sizes） confirmed that the formation of cyclohexanone was a structure sensitive reaction,and Pd particles of12-14 nm on Amberlyst-45 gave better selectivity and stability.
文摘The hydrogenation of m-dinitrobenzene to m-phenylenediamine in liquid phase was studied with the nickel catalysts supported on SiO2, TiO2, γ-Al2O3, MgO and diatomite carders. Based on the experiments of X-ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS）, temperature-programmed reduction （TPR）, temperature-programmed desorption of hydrogen （H2-TPD） and activity evaluation, the physico-chemical and catalytic properties of the catalysts were investigated. Among the catalysts tested, the SiO2 supported nickel catalyst showed the highest activity and selectivity towards m-phenylenediamine, over which 97.3% m-dinitrobenzene conversion and 95.1% m-phenylenediamine yield were obtained at 373K under hydrogen pressure of 2.6MPa after reaction for 6 h when using ethanol as solvent. Although TiO2 and diatomite supported nickel catalysts also presented high activity, they had lower selectivity towards m-phenylenediamine. As for γ-Al2O3 and MgO supported catalysts were almost inactive for the object reaction. It was shown that both the activity and selectivity of the catalysts were strongly depended on the interaction between nickel and the support. The higher activities of Ni/SiO2, Ni/TiO2 and Ni/diatomite could be attributed to the weaker metal-support interaction, on which Ni species presented as crystallized Ni metal particles. On the other hand, there existed strong metal-support interaction in Ni/MgO and Ni γ-Al2O3, which causes these catalysts more difficult to be reduced and the availability of Ni active sites decreased, resulting in their low catalytic activity.
文摘A series of perovskite type oxides and supported Ag catalysts were prepared, and characterized by X ray diffraction (XRD) and X ray photoelectron spectroscopy (XPS). The catalytic activities of the catalysts as well as influencing factors on catalytic activity have been investigated for the simultaneous removal of NOx and diesel soot particulate. An increase in catalytic activity for the selective reduction of NOx was observed with Ag addition in these perovskite oxides, especially with 5% Ag loading. This catalyst could be a promising candidate of catalytic material for the simultaneous elimination of NOx and diesel soot.
基金supported by the National Natural Science Foundation of China (21507130)the Chongqing Science and Technology Commission (cstc2016jcyjA 0070,cstc2014pt-gc20002,cstc2014yykfC 20003,cstckjcxljrc13)the Open Project Program of Chongqing Key Laboratory of Ca-talysis and Functional Organic Molecules from Chongqing Technology and Business University (1456029)~~
文摘To investigate how the physicochemical properties and NH3‐selective catalytic reduction(NH3‐SCR)performance of supported ceria‐based catalysts are influenced as a function of support type,a series of CeO2/SiO2,CeO2/γ‐Al2O3,CeO2/ZrO2,and CeO2/TiO2catalysts were prepared.The physicochemical properties were probed by means of X‐ray diffraction,Raman spectroscopy,Brunauer‐Emmett‐Teller surface area measurements,X‐ray photoelectron spectroscopy,H2‐temperature programmed reduction,and NH3‐temperature programmed desorption.Furthermore,the supported ceria‐based catalysts'catalytic performance and H2O+SO2tolerance were evaluated by the NH3‐SCR model reaction.The results indicate that out of the supported ceria‐based catalysts studied,the CeO2/γ‐Al2O3catalyst exhibits the highest catalytic activity as a result of having a high relative Ce3+/Ce4+ratio,optimum reduction behavior,and the largest total acid site concentration.Finally,the CeO2/γ‐Al2O3catalyst also presents excellent H2O+SO2tolerance during the NH3‐SCR process.
文摘Sodium-treated sepiolite(Na Sep)-supported transition metal catalysts(TM/Na Sep;TM = Cu, Fe, Ni, Mn, and Co) were synthesized via a rotary evaporation method. Physicochemical properties of the as-synthesized samples were characterized by means of various techniques, and their catalytic activities for HCHO(0.2%) oxidation were evaluated. Among the samples, Cu/Na Sep exhibited superior performance, and complete HCHO conversion was achieved at 100 ℃(GHSV = 240000 m L/(g·h)). Additionally, the sample retained good catalytic activity during a 42 h stability test. A number of factors, including elevated acidity, the abundance of oxygen species, and favorable low-temperature reducibility, were responsible for the excellent catalytic activity of Cu/Na Sep. According to the results of the in-situ DRIFTS characterization, the HCHO oxidation mechanism was as follows:(i) HCHO was rapidly decomposed into dioxymethylene(DOM) species on the Cu/Na Sep surface;(ii) DOM was then immediately converted to formate species;(iii) the resultant formate species were further oxidized to carbonates;(iv) the carbonate species were eventually converted to CO2 and H2O.
基金supported by the Scholarship from China Scholarship Council(CSC)(Grant no.201604910621)。
文摘Catalyst support is extremely important for future fuel cell devices.In this work,we developed doubleshelled C/TiO2(DSCT)hollow spheres as an excellent catalyst support via a template-directed method.The combination of hollow structure,TiO2 shell and carbon layer results in excellent electron conductivity,electrocatalytic activity,and chemical stability.These uniformed DSCT hollow spheres are used as catalyst support to synthesize Pt/DSCT hollow spheres electrocatalyst.The resulting Pt/DSCT hollow spheres exhibited high catalytic performance with a current density of 462 mA mg^-1 for methanol oxidation reaction,which is 2.52 times higher than that of the commercial Pt/C.Furthermore,the increased tolerance to carbonaceous poisoning with a higher If/Ibratio and a better long-term stability in acid media suggests that the DSCT hollow sphere is a promising C/TiO2-based catalyst support for direct methanol fuel cells applications.
基金National Natural Science Foundation of China (No. 20272062)
文摘Polyethylene (PE) grafting 4-vinylpyridine copolymers has been produced as powders of different rushes by theirradiation method. After treatment with methylaluminoxane (MAO), the copolymers were used as supports for Cp_2ZrCl_2catalyst Results of X-ray photoelectron spectroscopy, Fourier transforms infrared spectroscopy, ultraviolet spectroscopy andscanning electron microscope measurements show that the catalytic sites have been linked through MAO on the PE-graft-4-vinylpyridine (PEVP). The percentages of grafting 4-vinylpyridine and supported Cp_2ZrCl_2 depend on the size ofpolyethylene powder. The smaller the polyethylene powder, the more percent of 4-vinylpyridine groups and Cp_2ZrCl_2 existon the polyethylene chains, and the PEVP-supported catalyst has a relatively high activity for ethylene polymerization.
基金funded by National Natural Science Foundation of China(22022814,21878283)Youth Innovation Promotion Association CAS(2017223)+1 种基金"Strategic Priority Research Program"of the Chinese academy of Sciences(XDB17020100)the National Key projects for Fundamental Research and Development of China(2016YFA0202801)。
文摘Direct cost-effective conversion of abundant methane to high value-added oxygenates(methanol,formic acid,acetic acid,etc.)under mild conditions is prospective for optimizing the structure of energy resources.However,the CAH bond of products is more reactive than that of high thermodynamic stable methane.Exploring an appropriate approach to eliminate the‘‘seesaw effect"between methane conversion and oxygenate selectivity is significant.In this review,we briefly summarize the research progress in the past decade on low-temperature direct conversion of methane to oxygenates in gas-solid-liquid phase over various transition metal(Fe,Cu,Rh,Pd,Au Pd,etc.)based nanoparticle or single-atom catalyst.Furthermore,the prospects of catalyst design and catalysis process are also discussed.
基金financial support of the work by the U.S. Department of Energy (DOE), Office of Science, Basic Energy Sciences (BES), under Awards Grant Number DE-FG02-05ER15730
文摘An account of recent work on supported single‐atom catalyst design is given here for reactions as diverse as the low‐temperature water‐gas shift,methanol steam reforming,selective ethanol dehydrogenation,and selective hydrogenation of alkynes and dienes.It is of fundamental interest to investigate the intrinsic activity and selectivity of the active metal atom site and compare them to the properties of the corresponding metal nanoparticles and sub‐nm clusters.It is also important to understand what constitutes a stable active metal atom site in the various reaction environments,and maximize their loadings to allow us to design robust catalysts for industrial applications.Combined activity and stability studies,ideally following the evolution of the active site as a function of catalyst treatment in real time are recommended.Advanced characterization methods with atomic resolution will play a key role here and will be used to guide the design of new catalysts.
文摘An ultrasound-assisted heterogeneous catalytic oxidation process was applied to eliminate sulfur from commercial diesel fuel oil.The studied variables were catalyst concentration,type of catalyst(homogeneous or heterogeneous),oxidizing agent concentration,and the application of ultrasound energy.Supported catalysts were prepared by impregnation of coal fly ash with an iron(Ⅱ)sulfate aqueous solution using ultrasound energy.After drying,the catalyst was calcined at 500℃for 4 h.The oxidizing agent was hydrogen peroxide.Ultrasound energy was applied with a frequency of 47 kHz and an intensity of 147 W.Ethanol was employed for extracting the oxidized compounds from the hydrocarbon mixture.Coal fly ash and ethanol were used with the purpose of applying low-cost raw materials in chemical processes.It was found that under the studied conditions,increasing oxidizing agent concentration and the application of ultrasound energy can enhance the sulfur removal from commercial diesel fuel oil.Catalyst concentration did not play a significant role in the process.Similar results were obtained using homogeneous or heterogeneous catalyst,which is important since the heterogeneous catalyst could be recovered,reactivated,and used in many cycles.
基金financially supported by National Natural Science Foundation of China(Nos.21163015,21366027)the Doctor Foundation of Bingtuan(No.2014BB004)+2 种基金the National Basic Research Program of China(973Program,No. 2012CB720300)the Program for Changjiang Scholars,Innovative Research Team in University(No.IRT1161)the Program of Science and Technology Innovation Team in Bingtuan(No.2011CC001)
文摘Catalyst supports have very important effects on catalyst performance.A novel expanded multilayered vermiculite（EML-VMT） is successfully used as the catalyst support for the acetylene hydrochlorination.By mixing carbon on the surface of EML-VMT[i.e.,EML-VMT-C）,the HgCl2/EML-VMT-C achieved a high acetylene conversion of 97.3%,a vinyl chloride selectivity of 100%and a turn over frequency（TOF） value of 8.83 × 10^-3s^-1 at a temperature of 140 C,an acetylene gas hourly space velocity（GHSV） of 108 h^-1,and a feed volume ratio V（HC1）/V（C2H2） of 1.15.Moreover,the HgCl2/EML-VMT-C shows good stability.The EML-VMT also shows potential in the preparation of other EML-VMT-supported catalysts.
