Transmitted ultrasonic wave simulation （TUWS） in a digital core is one of the important elements of digital rock physics and is used to study wave propagation in porous cores and calculate equivalent velocity. When ...Transmitted ultrasonic wave simulation （TUWS） in a digital core is one of the important elements of digital rock physics and is used to study wave propagation in porous cores and calculate equivalent velocity. When simulating wave propagates in a 3D digital core, two additional layers are attached to its two surfaces vertical to the wave-direction and one planar wave source and two receiver-arrays are properly installed. After source excitation, the two receivers then record incident and transmitted waves of the digital rock. Wave propagating velocity, which is the velocity of the digital core, is computed by the picked peak-time difference between the two recorded waves. To evaluate the accuracy of TUWS, a digital core is fully saturated with gas, oil, and water to calculate the corresponding velocities. The velocities increase with decreasing wave frequencies in the simulation frequency band, and this is considered to be the result of scattering. When the pore fluids are varied from gas to oil and finally to water, the velocity-variation characteristics between the different frequencies are similar, thereby approximately following the variation law of velocities obtained from linear elastic statics simulation （LESS）, although their absolute values are different. However, LESS has been widely used. The results of this paper show that the transmission ultrasonic simulation has high relative precision.展开更多
Head waves are usually considered to be the refracted waves propagating along flat interfaces with an underlying higher velocity.However,the path that the rays travel along in media with irregular interfaces is not cl...Head waves are usually considered to be the refracted waves propagating along flat interfaces with an underlying higher velocity.However,the path that the rays travel along in media with irregular interfaces is not clear.Here we study the problem by simulation using a new approach of the spectral-element method with some overlapped elements（SEMO） that can accurately evaluate waves traveling along an irregular interface.Consequently,the head waves are separated from interface waves by a time window.Thus,their energy and arrival time changes can be analyzed independently.These analyses demonstrate that,contrary to the case for head waves propagating along a flat interface,there are two mechanisms for head waves traveling along an irregular interface：a refraction mechanism and transmission mechanism.That is,the head waves may be refracted waves propagating along the interface or transmitted waves induced by the waves propagating in the higher-velocity media.Such knowledge will be helpful in constructing a more accurate inversion method,such as head wave travel-time tomography,and in obtaining a more accurate model of subsurface structure which is very important for understanding the formation mechanism of some special areas,such as the Tibetan Plateau.展开更多
Comparisons of wave reflection, transmission and harmonics due to different types of sub merged structures are investigated by a numerical method, the boundary-fitted coordinate (BFC) method. The types of submerged st...Comparisons of wave reflection, transmission and harmonics due to different types of sub merged structures are investigated by a numerical method, the boundary-fitted coordinate (BFC) method. The types of submerged structures include a submerged horizontal plate, submerged breakwa ters (rectangular and trapezoidal) and a step-type structure (topography). First, the BFC method is ver ified by comparing the computed results with the experimental data, including wave surface elevations, reflected and transmitted wave heights, and amplitudes of higher harmonics, showing that the method is a reasonable one to predict wave deformations due to the submerged structures. Secondly, the wave sur face elevations and the higher harmonics over different submerged structures are compared. Thirdly, re flected and transmitted waves due to different submerged structures are investigated.展开更多
Transmissions of oblique incident wave from a row of rectangular piles are analyzed theoretically. The incident angle of plane wave is taken as g = 90° , there then is the transmission coefficient ｜T｜ = 1 （Thi...Transmissions of oblique incident wave from a row of rectangular piles are analyzed theoretically. The incident angle of plane wave is taken as g = 90° , there then is the transmission coefficient ｜T｜ = 1 （This is a paradox）. In this paper, by means of the approximate relation between the transmitted and incident wave angle found from the shape of a slit, the paradoxical phenomenon is removed. On the basis of the continuality of the pressure and flux and the analysis of flow resistance at the row of rectangular piles, formulas of reflection and transmission coefficients are obtained. The transmission and reflection coefficients predicted by the present model quite agree with those of laboratory experiments in previous references展开更多
This paper proposes a method of simultaneous determination of the four layer parameters （mass density, longitudinal velocity, the thickness and attenuation） of an immersed linear-viscoelastic thin layer by using the...This paper proposes a method of simultaneous determination of the four layer parameters （mass density, longitudinal velocity, the thickness and attenuation） of an immersed linear-viscoelastic thin layer by using the normally-incident reflected and transmitted ultrasonic waves. The analytical formula of the layer thickness related to the measured trans- mitted transfer functions is derived. The two determination steps of the four layer parameters are developed, in which acoustic impedance, time-of-flight and attenuation are first determined by the reflected transfer functions. Using the derived formula, it successively calculates and determines the layer thickness, longitudinal velocity and mass density by the measured transmitted transfer functions. According to the two determination steps, a more feasible and simplified measurement setups is described. It is found that only three signals （the reference waves, the reflected and transmitted waves） need to be recorded in the whole measurement for the determination of the four layer parameters. A study of the stability of the determination method against the experimental noises and the error analysis of the four layer parameters are made. This study lays the theoretical foundation of the practical measurement of a linear-viscoelastic thin layer.展开更多
In this paper, the theoretical calculation of floating breakwater performance in regular waves with arbitrary wave direction is discussed. Under the hypothesis of linearized system and applying the strip theory, we ca...In this paper, the theoretical calculation of floating breakwater performance in regular waves with arbitrary wave direction is discussed. Under the hypothesis of linearized system and applying the strip theory, we can solve the boundary condition problems of diffraction potential and radiation potential. Introducing the asymptotic expression of the wave velocity potential at infinity and using wave energy conservation, we can separately calculate the transmitted waves generated by the sway, heave and roll motion of the floating breakwater and by the fixed breakwater. Finally, we define the amplitude ratio of the transmitted wave to the incident wave as the transmitted wave coefficient CT which describes the floating breakwater effectiveness. Two examples are given and the theoretical results obtained by the present method agree well with experimental results.展开更多
This paper deals with the simultaneous inversion of velocity distribution and interface positions in a laterally heterogeneous medium using seismic travel time data. Due to the application of variable ...This paper deals with the simultaneous inversion of velocity distribution and interface positions in a laterally heterogeneous medium using seismic travel time data. Due to the application of variable step length and linear interpolation techniques (for both theoretical travel times and the partial derivative matrix), the computing speed is increased greatly. As compared with other domestic computing programs of this kind, it is five times or more faster than others. Besides reflected waves, the transmitted waves can also be used to form the partial derivative matrix of travel times with respect to interface positions. So this method can make full use of the information about interface positions contained in various transmitted waves and speed up the convergence rate. Digital tests and processing results of real data indicate the feasibility and effectiveness of the method and its program.展开更多
In the experiments of THz wave transmitting through the metallic cylindrical gratings fabricated by sub-wavelength brass wires, this paper reports that the discrepancy in the sharp resonances occurred as the grating p...In the experiments of THz wave transmitting through the metallic cylindrical gratings fabricated by sub-wavelength brass wires, this paper reports that the discrepancy in the sharp resonances occurred as the grating perpendicular or parallel to the electric vector are observed. A simulation based on the finite difference time domain （FDTD） indicated that the enhanced transmission through the grating is attributed to the combined effects of surface plasmons and cavity modes in the perpendicular condition, while the cavity modes dominate the resonant transmission under the other conditions. Additional experimental data and calculated results show that ~1 enhanced coupling efficiency can be realized in some THz frequency, which could be applied to the design and improvement of various optoelectronic devices, or detection of biological molecule and powder samples, etc.展开更多
In this Letter, we demonstrate a linear polarization conversion of transmitted terahertz wave with double-layer meta-grating surfaces, which integrated the frequency selectivity of a split ring resonator metasurface a...In this Letter, we demonstrate a linear polarization conversion of transmitted terahertz wave with double-layer meta-grating surfaces, which integrated the frequency selectivity of a split ring resonator metasurface and the polarization selectivity of a metallic grating surface. Since the double-layer can reduce the loss, and the Fabry- Perot like resonant effect between the two layers can improve the conversion efficiency, this converter can rotate the incident y-polarized terahertz wave into an x-polarized transmitted wave with relatively low loss and high efficiency. Experimental results show that an average conversion efficiency exceeding 75% from 0.25 to 0.65 THz with the highest efficiency of 90% at 0.43 THz with onlv -2 dB loss has been achieved.展开更多
基金supported by the Open Fund of the Key Laboratory of Exploration Technologies for Oil and Gas Resources(Yangtze University)the Ministry of Education(No.K2014-06)the Reservoir Geophysical Research Center at Yangtze University
文摘Transmitted ultrasonic wave simulation （TUWS） in a digital core is one of the important elements of digital rock physics and is used to study wave propagation in porous cores and calculate equivalent velocity. When simulating wave propagates in a 3D digital core, two additional layers are attached to its two surfaces vertical to the wave-direction and one planar wave source and two receiver-arrays are properly installed. After source excitation, the two receivers then record incident and transmitted waves of the digital rock. Wave propagating velocity, which is the velocity of the digital core, is computed by the picked peak-time difference between the two recorded waves. To evaluate the accuracy of TUWS, a digital core is fully saturated with gas, oil, and water to calculate the corresponding velocities. The velocities increase with decreasing wave frequencies in the simulation frequency band, and this is considered to be the result of scattering. When the pore fluids are varied from gas to oil and finally to water, the velocity-variation characteristics between the different frequencies are similar, thereby approximately following the variation law of velocities obtained from linear elastic statics simulation （LESS）, although their absolute values are different. However, LESS has been widely used. The results of this paper show that the transmission ultrasonic simulation has high relative precision.
基金supported by the National Natural Science Foundation of China (Grant Nos.40874027,90715020,and 90915012)the Institute of Geophysics of the China Earthquake Administration (Grant No.DQJB07B06)Special Public Welfare Industry (Grant Nos.20070804 and 200808008)
文摘Head waves are usually considered to be the refracted waves propagating along flat interfaces with an underlying higher velocity.However,the path that the rays travel along in media with irregular interfaces is not clear.Here we study the problem by simulation using a new approach of the spectral-element method with some overlapped elements（SEMO） that can accurately evaluate waves traveling along an irregular interface.Consequently,the head waves are separated from interface waves by a time window.Thus,their energy and arrival time changes can be analyzed independently.These analyses demonstrate that,contrary to the case for head waves propagating along a flat interface,there are two mechanisms for head waves traveling along an irregular interface：a refraction mechanism and transmission mechanism.That is,the head waves may be refracted waves propagating along the interface or transmitted waves induced by the waves propagating in the higher-velocity media.Such knowledge will be helpful in constructing a more accurate inversion method,such as head wave travel-time tomography,and in obtaining a more accurate model of subsurface structure which is very important for understanding the formation mechanism of some special areas,such as the Tibetan Plateau.
文摘Comparisons of wave reflection, transmission and harmonics due to different types of sub merged structures are investigated by a numerical method, the boundary-fitted coordinate (BFC) method. The types of submerged structures include a submerged horizontal plate, submerged breakwa ters (rectangular and trapezoidal) and a step-type structure (topography). First, the BFC method is ver ified by comparing the computed results with the experimental data, including wave surface elevations, reflected and transmitted wave heights, and amplitudes of higher harmonics, showing that the method is a reasonable one to predict wave deformations due to the submerged structures. Secondly, the wave sur face elevations and the higher harmonics over different submerged structures are compared. Thirdly, re flected and transmitted waves due to different submerged structures are investigated.
文摘Transmissions of oblique incident wave from a row of rectangular piles are analyzed theoretically. The incident angle of plane wave is taken as g = 90° , there then is the transmission coefficient ｜T｜ = 1 （This is a paradox）. In this paper, by means of the approximate relation between the transmitted and incident wave angle found from the shape of a slit, the paradoxical phenomenon is removed. On the basis of the continuality of the pressure and flux and the analysis of flow resistance at the row of rectangular piles, formulas of reflection and transmission coefficients are obtained. The transmission and reflection coefficients predicted by the present model quite agree with those of laboratory experiments in previous references
基金supported by the National Natural Science Foundation of China (Grant Nos. 10534040 and 40674059)the State Key Laboratory of Acoustics (IACAS) (Grant No. 200807)
文摘This paper proposes a method of simultaneous determination of the four layer parameters （mass density, longitudinal velocity, the thickness and attenuation） of an immersed linear-viscoelastic thin layer by using the normally-incident reflected and transmitted ultrasonic waves. The analytical formula of the layer thickness related to the measured trans- mitted transfer functions is derived. The two determination steps of the four layer parameters are developed, in which acoustic impedance, time-of-flight and attenuation are first determined by the reflected transfer functions. Using the derived formula, it successively calculates and determines the layer thickness, longitudinal velocity and mass density by the measured transmitted transfer functions. According to the two determination steps, a more feasible and simplified measurement setups is described. It is found that only three signals （the reference waves, the reflected and transmitted waves） need to be recorded in the whole measurement for the determination of the four layer parameters. A study of the stability of the determination method against the experimental noises and the error analysis of the four layer parameters are made. This study lays the theoretical foundation of the practical measurement of a linear-viscoelastic thin layer.
文摘In this paper, the theoretical calculation of floating breakwater performance in regular waves with arbitrary wave direction is discussed. Under the hypothesis of linearized system and applying the strip theory, we can solve the boundary condition problems of diffraction potential and radiation potential. Introducing the asymptotic expression of the wave velocity potential at infinity and using wave energy conservation, we can separately calculate the transmitted waves generated by the sway, heave and roll motion of the floating breakwater and by the fixed breakwater. Finally, we define the amplitude ratio of the transmitted wave to the incident wave as the transmitted wave coefficient CT which describes the floating breakwater effectiveness. Two examples are given and the theoretical results obtained by the present method agree well with experimental results.
文摘This paper deals with the simultaneous inversion of velocity distribution and interface positions in a laterally heterogeneous medium using seismic travel time data. Due to the application of variable step length and linear interpolation techniques (for both theoretical travel times and the partial derivative matrix), the computing speed is increased greatly. As compared with other domestic computing programs of this kind, it is five times or more faster than others. Besides reflected waves, the transmitted waves can also be used to form the partial derivative matrix of travel times with respect to interface positions. So this method can make full use of the information about interface positions contained in various transmitted waves and speed up the convergence rate. Digital tests and processing results of real data indicate the feasibility and effectiveness of the method and its program.
文摘In the experiments of THz wave transmitting through the metallic cylindrical gratings fabricated by sub-wavelength brass wires, this paper reports that the discrepancy in the sharp resonances occurred as the grating perpendicular or parallel to the electric vector are observed. A simulation based on the finite difference time domain （FDTD） indicated that the enhanced transmission through the grating is attributed to the combined effects of surface plasmons and cavity modes in the perpendicular condition, while the cavity modes dominate the resonant transmission under the other conditions. Additional experimental data and calculated results show that ~1 enhanced coupling efficiency can be realized in some THz frequency, which could be applied to the design and improvement of various optoelectronic devices, or detection of biological molecule and powder samples, etc.
基金supported by the National Natural Science Foundation of China(Nos.61531010,61270011,91438118,and 61501094)the National Key Basic Research Program of China(No.2014CB339806)
文摘In this Letter, we demonstrate a linear polarization conversion of transmitted terahertz wave with double-layer meta-grating surfaces, which integrated the frequency selectivity of a split ring resonator metasurface and the polarization selectivity of a metallic grating surface. Since the double-layer can reduce the loss, and the Fabry- Perot like resonant effect between the two layers can improve the conversion efficiency, this converter can rotate the incident y-polarized terahertz wave into an x-polarized transmitted wave with relatively low loss and high efficiency. Experimental results show that an average conversion efficiency exceeding 75% from 0.25 to 0.65 THz with the highest efficiency of 90% at 0.43 THz with onlv -2 dB loss has been achieved.
