The uniaxial compressive strength(UCS) of rock is an important parameter required for design and analysis of rock structures,and rock mass classification.Uniaxial compression test is the direct method to obtain the UC...The uniaxial compressive strength(UCS) of rock is an important parameter required for design and analysis of rock structures,and rock mass classification.Uniaxial compression test is the direct method to obtain the UCS values.However,these tests are generally tedious,time-consuming,expensive,and sometimes impossible to perform due to difficult rock conditions.Therefore,several empirical equations have been developed to estimate the UCS from results of index and physical tests of rock.Nevertheless,numerous empirical models available in the literature often make it difficult for mining engineers to decide which empirical equation provides the most reliable estimate of UCS.This study evaluates estimation of UCS of rocks from several empirical equations.The study uses data of point load strength(Is(50)),Schmidt rebound hardness(SRH),block punch index(BPI),effective porosity(n) and density(ρ)as inputs to empirically estimate the UCS.The estimated UCS values from empirical equations are compared with experimentally obtained or measured UCS values,using statistical analyses.It shows that the reliability of UCS estimated from empirical equations depends on the quality of data used to develop the equations,type of input data used in the equations,and the quality of input data from index or physical tests.The results show that the point load strength(Is(50)) is the most reliable index for estimating UCS among the five types of tests evaluated.Because of type-specific nature of rock,restricting the use of empirical equations to the similar rock types for which they are developed is one of the measures to ensure satisfactory prediction performance of empirical equations.展开更多
The purpose of this study was to clarify the relationships between results of index tests and uniaxial compressive strength (UCS) in hydrothermally altered soft rocks of the Upper Miocene, which are typical of the sof...The purpose of this study was to clarify the relationships between results of index tests and uniaxial compressive strength (UCS) in hydrothermally altered soft rocks of the Upper Miocene, which are typical of the soft rock found in northeastern Hokkaido, Japan. Index tests were performed using point load testing machine and needle penetrometer with irregular lump specimens under forced-dry, forced-wet, and natural-moist states. The relationships between irregular lump point load strength (IPLS) index and UCS, and needle penetration (NP) index and UCS were “UCS = approximately 19 IPLS index” and “UCS = 0.848 (NP index)0.619”, respectively, in soft rocks with a UCS below 25 MPa. These relationships could be applied to on-site tests of rocks with natural moisture content. The UCS could be calculated from IPLS and NP tests on soft rocks only when UCS was below 25 MPa, using the equations obtained as a result of this study.展开更多
It is generally accepted that the uniaxial compressive strength(UCS)and P-wave velocity of rocks tend to decrease simultaneously with increasing temperature.However,based on a great number of statistical data and syst...It is generally accepted that the uniaxial compressive strength(UCS)and P-wave velocity of rocks tend to decrease simultaneously with increasing temperature.However,based on a great number of statistical data and systematic analysis of the microstructure variation of rocks with temperature rising and corresponding propagation mechanism of elastic wave,the results show that(1)There are three different trends for the changes of UCS and P-wave velocity of sandstone when heated from room temperature(20C or 25C)to 800C:(i)Both the UCS and P-wave velocity decrease simultaneously;(ii)The UCS increases initially and then decreases,while the P-wave velocity decreases continuously;and(iii)The UCS increases initially and then fluctuates,while the P-wave velocity continuously decreases.(2)The UCS changes at room temperaturee400C,400Ce600C,and 600Ce800C are mainly attributed to the discrepancy of microstructure characteristics and quartz content,the transformation plasticity of clay minerals,and the balance between the thermal cementation and thermal damage,respectively.(3)The inconsistency in the trends of UCS and P-wave velocity changes is caused by the change of quartz content,phase transition of water and certain minerals.展开更多
The uniaxial compressive strength(UCS)of intact rock is one of the most important parameters required and determined for rock mechanics studies in engineering projects.The limitations and difficulty of conducting test...The uniaxial compressive strength(UCS)of intact rock is one of the most important parameters required and determined for rock mechanics studies in engineering projects.The limitations and difficulty of conducting tests on rocks,specifically on thinly bedded,highly fractured,highly porous and weak rocks,as well as the fact that these tests are destructive,expensive and time-consuming,lead to development of soft computing-based techniques.Application of artificial neural networks(ANNs)for predicting UCS has become an attractive alternative for geotechnical engineering scientists.In this study,an ANN was designed with the aim of indirectly predicting UCS through the serpentinization percentage,and physical,dynamic and mechanical characteristics of serpentinites.For this purpose,data obtained in earlier experimental work from central Greece were used.The ANN-based results were compared with the experimental ones and those obtained from previous analysis.The proposed ANN-based formula was found to be very efficient in predicting UCS values and the samples could be classified with simple physical,dynamic and mechanical tests,thus the expensive,difficult,time-consuming and destructive mechanical tests could be avoided.展开更多
The aim of this paper is to estimate the uniaxial compressive strength（UCS） of rocks with different characteristics by using genetic expression programming（GEP）.For this purpose,five different types of rocks inclu...The aim of this paper is to estimate the uniaxial compressive strength（UCS） of rocks with different characteristics by using genetic expression programming（GEP）.For this purpose,five different types of rocks including basalt and ignimbrite（black,yellow,gray,brown） were prepared.Values of unit weight,water absorption by weight,effective porosity and UCS of rocks were determined experimentally.By using these experimental data,five different GEP models were developed for estimating the values of UCS for different rock types.Good agreement between experimental data and predicted results is obtained.展开更多
To better understand the failure behaviours and strength of bolt-reinforced blocky rocks,large scale extensive laboratory experiments are carried out on blocky rock-like specimens with and without rockbolt reinforceme...To better understand the failure behaviours and strength of bolt-reinforced blocky rocks,large scale extensive laboratory experiments are carried out on blocky rock-like specimens with and without rockbolt reinforcement.The results show that both shear failure and tensile failure along joint surfaces are observed but the shear failure is a main controlling factor for the peak strength of the rock mass with and without rockbolts.The rockbolts are necked and shear deformation simultaneously happens in bolt reinforced rock specimens.As the joint dip angle increases,the joint shear failure becomes more dominant.The number of rockbolts has a significant impact on the peak strain and uniaxial compressive strength(UCS),but little influence on the deformation modulus of the rock mass.Using the Winkler beam model to represent the rockbolt behaviours,an analytical model for the prediction of the strength of boltreinforced blocky rocks is proposed.Good agreement between the UCS values predicted by proposed model and obtained from experiments suggest an encouraging performance of the proposed model.In addition,the performance of the proposed model is further assessed using published results in the literature,indicating the proposed model can be used effectively in the prediction of UCS of bolt-reinforced blocky rocks.展开更多
The difficulties associated with performing direct compression strength tests on rocks lead to the development of indirect test methods for the rock strength assessment. Indirect test methods are simple, more economic...The difficulties associated with performing direct compression strength tests on rocks lead to the development of indirect test methods for the rock strength assessment. Indirect test methods are simple, more economical, less time-consuming, and easily adaptable to the field. The main aim of this study was to derive correlations between direct and indirect test methods for basalt and rhyolite rock types from Carlin trend deposits in Nevada. In the destructive methods, point load index, block punch index, and splitting tensile strength tests are performed. In the non-destructive methods, Schmidt hammer and ultrasonic pulse velocity tests are performed. Correlations between the direct and indirect compression strength tests are developed using linear and nonlinear regression analysis methods. The results show that the splitting tensile strength has the best correlation with the uniaxial compression strength.Furthermore, the Poisson's ratio has no correlation with any of the direct and indirect test results.展开更多
The uniaxial compression tests of cylinder standard specimens and different dimension cube specimens of No.13 coal seam of Jianxin Colliery were carried out using MTS, and the basic mechanics parameters of Jianxin Col...The uniaxial compression tests of cylinder standard specimens and different dimension cube specimens of No.13 coal seam of Jianxin Colliery were carried out using MTS, and the basic mechanics parameters of Jianxin Colliery 13 coal were studied. The dimension-form effect of uniaxial compression strength was analyzed. The exponent formula σc=6.928＋130.269 8 exp（-0.105 95D）of dimension effect was fitted. While the side length of specimen reaches 80 mm, its unaxial strength tends to a stable value which is called to be the strength of coal mass. Studies indicates that since the cube specimen suffered more shake than the cylinder one during machining and processing and the stress is centralized at four corners of cube during compressive experiment, the coal strength of standard cylinder specimen is higher than that of cube one.展开更多
This paper provides a review of the intrinsic and extrinsic factors affecting the uniaxial compressive strength(UCS)of cemented tailings backfill(CTB).The consideration is that once CTB is poured into underground stop...This paper provides a review of the intrinsic and extrinsic factors affecting the uniaxial compressive strength(UCS)of cemented tailings backfill(CTB).The consideration is that once CTB is poured into underground stopes,its strength is heavily influenced by factors internal to the CTB as well as the surrounding mining environments.Peer-reviewed journal articles,books,and conference papers published between 2000 and 2022 were searched electronically from various databases and reviewed.Additional sources,such as doctoral theses,were obtained from academic repositories.An important finding from the review is that the addition of fibers was reported to improve the UCS of CTB in some studies while decrease in others.This discrepancy was accounted to the different properties of fibers used.Further research is therefore needed to determine the“preferred”fiber to be used in CTB.Diverging findings were also reported on the effects of stope size on the UCS of CTB.Furthermore,the use of fly ash as an alternative binder may be threatened in the future when reliance on the coal power declines.Therefore,an alternative cementitious by-product to be used together with furnace slag may be required in the future.Finally,while most studies on backfill focused on single-layered structures,layered backfill design models should also be investigated.展开更多
In northeastern Sicily(Italy),sandstone rock masses widely crop out as cover deposits over crystalline terrains belonging to the orogenic belt.Despite being part of the same geological formation,these sandstones are c...In northeastern Sicily(Italy),sandstone rock masses widely crop out as cover deposits over crystalline terrains belonging to the orogenic belt.Despite being part of the same geological formation,these sandstones are characterized by highly different features in terms of texture and physico-mechanical properties.This poses a scientific question on the possibility of tracing these rocks to a single statistical model,which could be representative of their main engineering geological properties.Therefore,it is worth investigating on the possible reasons of such differences,that should be searched either in the current geographical sandstone distribution or in the rock texture.For this study,sandstone samples were collected from different sites and were analyzed at both the hand and thin section scales.Three sandstone types were recognized,characterized by a different texture.Then,the laboratory characterization allowed estimating their main physico-mechanical and ultrasonic properties,such as porosity,density,mechanical strength,deformability,and ultrasonic velocities.The rock mechanical strength proved linked to the rock compactness and to the presence of lithic fragments,while pores and a pseudo-matrix between grains represent weakening features.Rock data were also statistically analyzed by grouping the specimens according to a geographical criterion,with respect to their sampling area,but no link was found between location and rock properties.Finally,with the aim of achieving mathematical laws that could be used to predict some rock properties from others,useful for practical purposes when dealing with such a high property variability,single and multiple regression analyses were carried out.Results show that the Uniaxial Compressive Strength,porosity,and P-wave velocity are the best predictors for a quick,indirect estimation of the main physico-mechanical parameters.The methodological approach developed for this research can be taken as reference to study other worldwide cases,involving rocks characterized by a wide range of physico-mechanical properties and covering large regional territories.展开更多
The mechanical characteristics and acoustic behavior of rock masses are greatly influenced by stochastic joints.In this study,numerical models of rock masses incorporating intermittent joints with different numbers an...The mechanical characteristics and acoustic behavior of rock masses are greatly influenced by stochastic joints.In this study,numerical models of rock masses incorporating intermittent joints with different numbers and dip angles were produced using the finite element method(FEM)with the intrinsic cohesive zone model(ICZM).Then,the uniaxial compressive and wave propagation simulations were performed.The results indicate that the joint number and dip angle can affect the mechanical and acoustic properties of the models.The uniaxial compressive strength(UCS)and wave velocity of rock masses decrease monotonically as the joint number increases.However,the wave velocity grows monotonically as the joint dip angle increases.When the joint dip angle is 45°–60°,the UCS of the rock mass is lower than that of other dip angles.The wave velocity parallel to the joints is greater than that perpendicular to the joints.When the dip angle of joints remains unchanged,the UCS and wave velocity are positively related.When the joint dip angle increases,the variation amplitude of the UCS regarding the wave velocity increases.To reveal the effect of the joint distribution on the velocity,a theoretical model was also proposed.According to the theoretical wave velocity,the change in wave velocity of models with various joint numbers and dip angles was consistent with the simulation results.Furthermore,a theoretical indicator(i.e.fabric tensor)was adopted to analyze the variation of the wave velocity and UCS.展开更多
Several constructions in the field of civil engineering quite often need to deal with rocks.Strength behaviour of rock intersected by a discontinuity or a set of discontinuities has been a topic of keen interest for e...Several constructions in the field of civil engineering quite often need to deal with rocks.Strength behaviour of rock intersected by a discontinuity or a set of discontinuities has been a topic of keen interest for engineering community.The popular attributes of discontinuities that have been given due importance are their frequency,orientation and surface characteristics.Non-persistency,however,has been given little attention.This article presents an experimental study wherein focus has been made on the effect of non-persistency of the joint on the uniaxial compressive strength(UCS)of a model rock for various geometries such as orientation,discontinuity length ratio and number of joint segments.The applicability of single plane of weakness theory(SPWT)to assess the strength of jointed specimens has also been evaluated.It has been noticed that SPWT captures the strength behaviour only for a narrow range of discontinuity orientations.As an improvement,an approach is suggested by extending concepts of degree of persistence and joint factor to have a better understanding towards strength behaviour of rocks intersected by non-persistent joints.展开更多
The Hoek-Brown (HB) failure criterion and the geological strength index (GSI) were developed for the estimation of rock mass strength in jointed and blocky ground where rock mass failure is dominated by sliding along ...The Hoek-Brown (HB) failure criterion and the geological strength index (GSI) were developed for the estimation of rock mass strength in jointed and blocky ground where rock mass failure is dominated by sliding along open joints and rotation of rock blocks. In massive, veined and moderately jointed rock in which rock blocks cannot form without failure of intact rock, the approach to obtain HB parameters must be modified. Typical situations when these modifications are required include the design of pillars, excavation and cavern stability, strainburst potential assessment, and tunnel support in deep underground conditions (around σ1/σci > 0.15, where σ1 is the major principal compressive stress and σci is the unconfined compressive strength of the homogeneous rock) in hard brittle rocks with GSI ≥ 65. In this article, the strength of massive to moderately jointed hard rock masses is investigated, and an approach is presented to estimate the rock mass strength envelope using laboratory data from uniaxial and triaxial compressive strength tests without reliance on the HB-GSI equations. The data from tests on specimens obtained from massive to moderately jointed heterogeneous (veined) rock masses are used to obtain the rock and rock mass strengths at confining stress ranges that are relevant for deep tunnelling and mining;and a methodology is presented for this purpose from laboratory data alone. By directly obtaining the equivalent HB rock mass strength envelope for massive to moderately jointed rock from laboratory tests, the HB-GSI rock mass strength estimation approach is complemented for conditions where the GSIequations are not applicable. Guidance is also provided on how to apply the proposed approach when laboratory test data are not or not yet available.展开更多
The influence of source concrete (SC) with different compression strengths on the workability and mechanical properties of recycled mortar made with river sand substituted by 100% fine recycled concrete aggregates (FR...The influence of source concrete (SC) with different compression strengths on the workability and mechanical properties of recycled mortar made with river sand substituted by 100% fine recycled concrete aggregates (FRCA) is experimentally investigated. The basic physical performance test shows that with the increase in SC strength, FRCA exhibit lower water absorption and crushing index, meanwhile keeping higher densities. Mechanical property tests, including compressive strength, flexural strength and uniaxial compressive stress-strain tests, show that compressive strength,flexural strength and elasticity modulus of recycled sand mortars increase roughly with the increase in SC strength. The proposed mixture design method demonstrates that all of the components can be kept as the same as those in natural mortar mixture design and FRCA must be pre-wetted before making mortar mixture. Meanwhile, the reuse of higher strength SC can ensure that recycled mortar mixtures are able to achieve similar mechanical performance when compared to natural mortar designs.展开更多
Appropriate rock characterization is beneficial in providing a reliable judgment on rock properties which is crucial for the design process of rock engineering applications.However,it can be difficult to obtain consis...Appropriate rock characterization is beneficial in providing a reliable judgment on rock properties which is crucial for the design process of rock engineering applications.However,it can be difficult to obtain consistent mechanical parameters due to substantial variations in rock properties.In this research,uniaxial compression tests on dolerite specimens collected from a gold mine in Western Australia showed substantial scatter in the results.Rock categorization based on the P-wave velocities is as accurate as the thin section analysis,which suggests that they can be used together to gain a more accurate initial understanding of the rock types before any laboratory testing.The quality of specimen preparation and rockemachine interaction greatly affect the test results.For instance,non-parallelness of loading platens can lead to considerable scatter of the testing results,which would be perceived as rock variability.It is suggested that the current testing standards should be modified towards a better control of the loading machine performance and equipment precision.Finally,the possibility of pre-existing microcracks in rock,neither detected by the thin section analysis nor by the ultrasonic measurement,must be examined by computed tomography(CT)scanning as they can affect the test results.This study will enhance our knowledge about the sources of variability in laboratory test results of rock which is essential for obtaining reliable data.展开更多
文摘The uniaxial compressive strength(UCS) of rock is an important parameter required for design and analysis of rock structures,and rock mass classification.Uniaxial compression test is the direct method to obtain the UCS values.However,these tests are generally tedious,time-consuming,expensive,and sometimes impossible to perform due to difficult rock conditions.Therefore,several empirical equations have been developed to estimate the UCS from results of index and physical tests of rock.Nevertheless,numerous empirical models available in the literature often make it difficult for mining engineers to decide which empirical equation provides the most reliable estimate of UCS.This study evaluates estimation of UCS of rocks from several empirical equations.The study uses data of point load strength(Is(50)),Schmidt rebound hardness(SRH),block punch index(BPI),effective porosity(n) and density(ρ)as inputs to empirically estimate the UCS.The estimated UCS values from empirical equations are compared with experimentally obtained or measured UCS values,using statistical analyses.It shows that the reliability of UCS estimated from empirical equations depends on the quality of data used to develop the equations,type of input data used in the equations,and the quality of input data from index or physical tests.The results show that the point load strength(Is(50)) is the most reliable index for estimating UCS among the five types of tests evaluated.Because of type-specific nature of rock,restricting the use of empirical equations to the similar rock types for which they are developed is one of the measures to ensure satisfactory prediction performance of empirical equations.
文摘The purpose of this study was to clarify the relationships between results of index tests and uniaxial compressive strength (UCS) in hydrothermally altered soft rocks of the Upper Miocene, which are typical of the soft rock found in northeastern Hokkaido, Japan. Index tests were performed using point load testing machine and needle penetrometer with irregular lump specimens under forced-dry, forced-wet, and natural-moist states. The relationships between irregular lump point load strength (IPLS) index and UCS, and needle penetration (NP) index and UCS were “UCS = approximately 19 IPLS index” and “UCS = 0.848 (NP index)0.619”, respectively, in soft rocks with a UCS below 25 MPa. These relationships could be applied to on-site tests of rocks with natural moisture content. The UCS could be calculated from IPLS and NP tests on soft rocks only when UCS was below 25 MPa, using the equations obtained as a result of this study.
基金This work was supported by the National Natural Science Foundation of China(Grant No.41772333)the program of State Key Laboratory of Frozen Soil Engineering(Grant No.SKLFSE201713)the Shaanxi Province New-Star Talents Promotion Project of Science and Technology(Grant No.2019KJXX-049).
文摘It is generally accepted that the uniaxial compressive strength(UCS)and P-wave velocity of rocks tend to decrease simultaneously with increasing temperature.However,based on a great number of statistical data and systematic analysis of the microstructure variation of rocks with temperature rising and corresponding propagation mechanism of elastic wave,the results show that(1)There are three different trends for the changes of UCS and P-wave velocity of sandstone when heated from room temperature(20C or 25C)to 800C:(i)Both the UCS and P-wave velocity decrease simultaneously;(ii)The UCS increases initially and then decreases,while the P-wave velocity decreases continuously;and(iii)The UCS increases initially and then fluctuates,while the P-wave velocity continuously decreases.(2)The UCS changes at room temperaturee400C,400Ce600C,and 600Ce800C are mainly attributed to the discrepancy of microstructure characteristics and quartz content,the transformation plasticity of clay minerals,and the balance between the thermal cementation and thermal damage,respectively.(3)The inconsistency in the trends of UCS and P-wave velocity changes is caused by the change of quartz content,phase transition of water and certain minerals.
文摘The uniaxial compressive strength(UCS)of intact rock is one of the most important parameters required and determined for rock mechanics studies in engineering projects.The limitations and difficulty of conducting tests on rocks,specifically on thinly bedded,highly fractured,highly porous and weak rocks,as well as the fact that these tests are destructive,expensive and time-consuming,lead to development of soft computing-based techniques.Application of artificial neural networks(ANNs)for predicting UCS has become an attractive alternative for geotechnical engineering scientists.In this study,an ANN was designed with the aim of indirectly predicting UCS through the serpentinization percentage,and physical,dynamic and mechanical characteristics of serpentinites.For this purpose,data obtained in earlier experimental work from central Greece were used.The ANN-based results were compared with the experimental ones and those obtained from previous analysis.The proposed ANN-based formula was found to be very efficient in predicting UCS values and the samples could be classified with simple physical,dynamic and mechanical tests,thus the expensive,difficult,time-consuming and destructive mechanical tests could be avoided.
基金The support of the Research Fund of Kahramanmaras Sutcu Imam University(Grant FBE2009/3-9YLS)
文摘The aim of this paper is to estimate the uniaxial compressive strength（UCS） of rocks with different characteristics by using genetic expression programming（GEP）.For this purpose,five different types of rocks including basalt and ignimbrite（black,yellow,gray,brown） were prepared.Values of unit weight,water absorption by weight,effective porosity and UCS of rocks were determined experimentally.By using these experimental data,five different GEP models were developed for estimating the values of UCS for different rock types.Good agreement between experimental data and predicted results is obtained.
基金supported by the National Key Research and Development Projects of China(No.2021YFB2600402)National Natural Science Foundation of China(Nos.52209148 and 52374119)+1 种基金the opening fund of State Key Laboratory of Geomechanics and Geotechnical Engineering,Institute of Rock and Soil Mechanics,Chinese Academy of Sciences(No.SKLGME023023)the opening fund of Key Laboratory of Water Management and Water Security for Yellow River Basin,Ministry of Water Resources(No.2023-SYSJJ-02)。
文摘To better understand the failure behaviours and strength of bolt-reinforced blocky rocks,large scale extensive laboratory experiments are carried out on blocky rock-like specimens with and without rockbolt reinforcement.The results show that both shear failure and tensile failure along joint surfaces are observed but the shear failure is a main controlling factor for the peak strength of the rock mass with and without rockbolts.The rockbolts are necked and shear deformation simultaneously happens in bolt reinforced rock specimens.As the joint dip angle increases,the joint shear failure becomes more dominant.The number of rockbolts has a significant impact on the peak strain and uniaxial compressive strength(UCS),but little influence on the deformation modulus of the rock mass.Using the Winkler beam model to represent the rockbolt behaviours,an analytical model for the prediction of the strength of boltreinforced blocky rocks is proposed.Good agreement between the UCS values predicted by proposed model and obtained from experiments suggest an encouraging performance of the proposed model.In addition,the performance of the proposed model is further assessed using published results in the literature,indicating the proposed model can be used effectively in the prediction of UCS of bolt-reinforced blocky rocks.
基金CDC/NIOSH for their partial funding of this work
文摘The difficulties associated with performing direct compression strength tests on rocks lead to the development of indirect test methods for the rock strength assessment. Indirect test methods are simple, more economical, less time-consuming, and easily adaptable to the field. The main aim of this study was to derive correlations between direct and indirect test methods for basalt and rhyolite rock types from Carlin trend deposits in Nevada. In the destructive methods, point load index, block punch index, and splitting tensile strength tests are performed. In the non-destructive methods, Schmidt hammer and ultrasonic pulse velocity tests are performed. Correlations between the direct and indirect compression strength tests are developed using linear and nonlinear regression analysis methods. The results show that the splitting tensile strength has the best correlation with the uniaxial compression strength.Furthermore, the Poisson's ratio has no correlation with any of the direct and indirect test results.
文摘The uniaxial compression tests of cylinder standard specimens and different dimension cube specimens of No.13 coal seam of Jianxin Colliery were carried out using MTS, and the basic mechanics parameters of Jianxin Colliery 13 coal were studied. The dimension-form effect of uniaxial compression strength was analyzed. The exponent formula σc=6.928＋130.269 8 exp（-0.105 95D）of dimension effect was fitted. While the side length of specimen reaches 80 mm, its unaxial strength tends to a stable value which is called to be the strength of coal mass. Studies indicates that since the cube specimen suffered more shake than the cylinder one during machining and processing and the stress is centralized at four corners of cube during compressive experiment, the coal strength of standard cylinder specimen is higher than that of cube one.
文摘This paper provides a review of the intrinsic and extrinsic factors affecting the uniaxial compressive strength(UCS)of cemented tailings backfill(CTB).The consideration is that once CTB is poured into underground stopes,its strength is heavily influenced by factors internal to the CTB as well as the surrounding mining environments.Peer-reviewed journal articles,books,and conference papers published between 2000 and 2022 were searched electronically from various databases and reviewed.Additional sources,such as doctoral theses,were obtained from academic repositories.An important finding from the review is that the addition of fibers was reported to improve the UCS of CTB in some studies while decrease in others.This discrepancy was accounted to the different properties of fibers used.Further research is therefore needed to determine the“preferred”fiber to be used in CTB.Diverging findings were also reported on the effects of stope size on the UCS of CTB.Furthermore,the use of fly ash as an alternative binder may be threatened in the future when reliance on the coal power declines.Therefore,an alternative cementitious by-product to be used together with furnace slag may be required in the future.Finally,while most studies on backfill focused on single-layered structures,layered backfill design models should also be investigated.
文摘In northeastern Sicily(Italy),sandstone rock masses widely crop out as cover deposits over crystalline terrains belonging to the orogenic belt.Despite being part of the same geological formation,these sandstones are characterized by highly different features in terms of texture and physico-mechanical properties.This poses a scientific question on the possibility of tracing these rocks to a single statistical model,which could be representative of their main engineering geological properties.Therefore,it is worth investigating on the possible reasons of such differences,that should be searched either in the current geographical sandstone distribution or in the rock texture.For this study,sandstone samples were collected from different sites and were analyzed at both the hand and thin section scales.Three sandstone types were recognized,characterized by a different texture.Then,the laboratory characterization allowed estimating their main physico-mechanical and ultrasonic properties,such as porosity,density,mechanical strength,deformability,and ultrasonic velocities.The rock mechanical strength proved linked to the rock compactness and to the presence of lithic fragments,while pores and a pseudo-matrix between grains represent weakening features.Rock data were also statistically analyzed by grouping the specimens according to a geographical criterion,with respect to their sampling area,but no link was found between location and rock properties.Finally,with the aim of achieving mathematical laws that could be used to predict some rock properties from others,useful for practical purposes when dealing with such a high property variability,single and multiple regression analyses were carried out.Results show that the Uniaxial Compressive Strength,porosity,and P-wave velocity are the best predictors for a quick,indirect estimation of the main physico-mechanical parameters.The methodological approach developed for this research can be taken as reference to study other worldwide cases,involving rocks characterized by a wide range of physico-mechanical properties and covering large regional territories.
基金financial support from the National Key R&D Program of China(Grant No.2020YFA0711802).
文摘The mechanical characteristics and acoustic behavior of rock masses are greatly influenced by stochastic joints.In this study,numerical models of rock masses incorporating intermittent joints with different numbers and dip angles were produced using the finite element method(FEM)with the intrinsic cohesive zone model(ICZM).Then,the uniaxial compressive and wave propagation simulations were performed.The results indicate that the joint number and dip angle can affect the mechanical and acoustic properties of the models.The uniaxial compressive strength(UCS)and wave velocity of rock masses decrease monotonically as the joint number increases.However,the wave velocity grows monotonically as the joint dip angle increases.When the joint dip angle is 45°–60°,the UCS of the rock mass is lower than that of other dip angles.The wave velocity parallel to the joints is greater than that perpendicular to the joints.When the dip angle of joints remains unchanged,the UCS and wave velocity are positively related.When the joint dip angle increases,the variation amplitude of the UCS regarding the wave velocity increases.To reveal the effect of the joint distribution on the velocity,a theoretical model was also proposed.According to the theoretical wave velocity,the change in wave velocity of models with various joint numbers and dip angles was consistent with the simulation results.Furthermore,a theoretical indicator(i.e.fabric tensor)was adopted to analyze the variation of the wave velocity and UCS.
文摘Several constructions in the field of civil engineering quite often need to deal with rocks.Strength behaviour of rock intersected by a discontinuity or a set of discontinuities has been a topic of keen interest for engineering community.The popular attributes of discontinuities that have been given due importance are their frequency,orientation and surface characteristics.Non-persistency,however,has been given little attention.This article presents an experimental study wherein focus has been made on the effect of non-persistency of the joint on the uniaxial compressive strength(UCS)of a model rock for various geometries such as orientation,discontinuity length ratio and number of joint segments.The applicability of single plane of weakness theory(SPWT)to assess the strength of jointed specimens has also been evaluated.It has been noticed that SPWT captures the strength behaviour only for a narrow range of discontinuity orientations.As an improvement,an approach is suggested by extending concepts of degree of persistence and joint factor to have a better understanding towards strength behaviour of rocks intersected by non-persistent joints.
基金Rio Tinto for sponsoring much of the work outlined in this article through the Rio Tinto Centre for Underground Mine Construction (an affiliate of CEMI)the financial contributions of NSERC (Natural Sciences and Engineering Research Council of Canada)
文摘The Hoek-Brown (HB) failure criterion and the geological strength index (GSI) were developed for the estimation of rock mass strength in jointed and blocky ground where rock mass failure is dominated by sliding along open joints and rotation of rock blocks. In massive, veined and moderately jointed rock in which rock blocks cannot form without failure of intact rock, the approach to obtain HB parameters must be modified. Typical situations when these modifications are required include the design of pillars, excavation and cavern stability, strainburst potential assessment, and tunnel support in deep underground conditions (around σ1/σci > 0.15, where σ1 is the major principal compressive stress and σci is the unconfined compressive strength of the homogeneous rock) in hard brittle rocks with GSI ≥ 65. In this article, the strength of massive to moderately jointed hard rock masses is investigated, and an approach is presented to estimate the rock mass strength envelope using laboratory data from uniaxial and triaxial compressive strength tests without reliance on the HB-GSI equations. The data from tests on specimens obtained from massive to moderately jointed heterogeneous (veined) rock masses are used to obtain the rock and rock mass strengths at confining stress ranges that are relevant for deep tunnelling and mining;and a methodology is presented for this purpose from laboratory data alone. By directly obtaining the equivalent HB rock mass strength envelope for massive to moderately jointed rock from laboratory tests, the HB-GSI rock mass strength estimation approach is complemented for conditions where the GSIequations are not applicable. Guidance is also provided on how to apply the proposed approach when laboratory test data are not or not yet available.
基金The National Key Research and Development Programm of China(No.2018YFD1100402-05)the National Natural Science Foundation of China(No.6505000184)
文摘The influence of source concrete (SC) with different compression strengths on the workability and mechanical properties of recycled mortar made with river sand substituted by 100% fine recycled concrete aggregates (FRCA) is experimentally investigated. The basic physical performance test shows that with the increase in SC strength, FRCA exhibit lower water absorption and crushing index, meanwhile keeping higher densities. Mechanical property tests, including compressive strength, flexural strength and uniaxial compressive stress-strain tests, show that compressive strength,flexural strength and elasticity modulus of recycled sand mortars increase roughly with the increase in SC strength. The proposed mixture design method demonstrates that all of the components can be kept as the same as those in natural mortar mixture design and FRCA must be pre-wetted before making mortar mixture. Meanwhile, the reuse of higher strength SC can ensure that recycled mortar mixtures are able to achieve similar mechanical performance when compared to natural mortar designs.
基金the Curtin Strategic International Research Scholarship(CSIRS)and Mining Research Institute of Western Australia(MRIWA)-project M474 scholarshipthe Australian Research Council through project DP190103260.
文摘Appropriate rock characterization is beneficial in providing a reliable judgment on rock properties which is crucial for the design process of rock engineering applications.However,it can be difficult to obtain consistent mechanical parameters due to substantial variations in rock properties.In this research,uniaxial compression tests on dolerite specimens collected from a gold mine in Western Australia showed substantial scatter in the results.Rock categorization based on the P-wave velocities is as accurate as the thin section analysis,which suggests that they can be used together to gain a more accurate initial understanding of the rock types before any laboratory testing.The quality of specimen preparation and rockemachine interaction greatly affect the test results.For instance,non-parallelness of loading platens can lead to considerable scatter of the testing results,which would be perceived as rock variability.It is suggested that the current testing standards should be modified towards a better control of the loading machine performance and equipment precision.Finally,the possibility of pre-existing microcracks in rock,neither detected by the thin section analysis nor by the ultrasonic measurement,must be examined by computed tomography(CT)scanning as they can affect the test results.This study will enhance our knowledge about the sources of variability in laboratory test results of rock which is essential for obtaining reliable data.
