The goal is to develop a hybrid IPN network of polyvinyl acetate (PVAc) and ethylene-vinyl acetate (VAE). In this research work, the vinyl acetate (VAc)/ VAE hybrid emulsion and polyvinyl acetate emulsion (PVAc) were ...The goal is to develop a hybrid IPN network of polyvinyl acetate (PVAc) and ethylene-vinyl acetate (VAE). In this research work, the vinyl acetate (VAc)/ VAE hybrid emulsion and polyvinyl acetate emulsion (PVAc) were effectively synthesized. Emulsions with various characteristics have been developed by adjusting the weight ratios between the vinyl acetate monomer and the VAE component. The impacts on the mechanical, thermal, and physical properties of the films were investigated using tests for pencil hardness, tensile shear strength, pH, contact angle measurement, differential scanning calorimetry (DSC), and viscosity. When 5.0 weight percent VAE was added, the tensile shear strength in dry conditions decreased by 18.75% after a 24-hour bonding period, the heat resistance decreased by 26.29% (as per WATT 91) and the tensile shear strength decreased by approximately 36.52% in wet conditions (per EN 204). The pristine sample’s results were also confirmed by the contact angle test. The interpenetrating network (IPN) formation in hybrid PVAc emulsion as primary bonds does not directly attach to PVAc and VAE chains. The addition of VAE reduced the mechanical properties (at dry conditions) and heat resistance as per WATT 91. Contact angle analysis demonstrated that PVAc adhesives containing VAE had increased water resistance when compared to conventional PVA stabilised PVAc homopolymer-based adhesives. When compared to virgin PVAc Homo, the water resistance of the PVAc emulsion polymerization was enhanced by the addition of VAE.展开更多
Polyamide 6 (PA6) was employed as a charring agent of intumescent flame retardant (IFR) to improve the flame retardancy of ethylene-vinyl acetate copolymer (EVA). Different processing procedures were used to regulate ...Polyamide 6 (PA6) was employed as a charring agent of intumescent flame retardant (IFR) to improve the flame retardancy of ethylene-vinyl acetate copolymer (EVA). Different processing procedures were used to regulate the localization of IFR in the EVA matrix. Localizations in which IFR was dispersed in the PA6phase or in the EVA phase were prepared. The effect of the localization of IFR on the flame retardancy of EVA was investigated. The limited oxygen index (LOI), vertical burning (UL 94) and cone calorimeter test (CCT)showed that the localization of IFR in the EVA matrix exhibited a remarkable influence on the flame retardancy.Compared with EVA/IFR, a weak improvement in the flame retardancy was observed in the EVA/PA6/IFR blend withthe localization of IFR in the PA6 phase. When IFR was regulated from the PA6 phase to the EVA matrix,a remarkable increase in the flame retardancy was exhibited. The LOI was increased from 27.8%to 32.7%, and the UL 94 vertical rating was increased from V-2 to V-0. Moreover, an approximately 41.36%decrease in the peak heat release rate was exhibited. A continuous and compact intumescent charring layer that formed in the blends with the localization of IFR in the EVA matrix should be responsible for its excellent flame retardancy.展开更多
Polyvinyl alcohol (PVA) colloid stabilized Polyvinyl acetate (PVAc) based wood adhesive has poor performance in highly humid conditions. Currently, the addition of natural fillers in the wood adhesive is one of the mo...Polyvinyl alcohol (PVA) colloid stabilized Polyvinyl acetate (PVAc) based wood adhesive has poor performance in highly humid conditions. Currently, the addition of natural fillers in the wood adhesive is one of the most effective ways to enhance the performance of PVAc wood adhesive in highly moist conditions. Microcrystalline cellulose (MCC) are strong renewable, bio-based material and has great potential in a reinforcement of the polymeric matrix. Hence, the present work investigates the applicability of microcrystalline cellulose incorporated 3% and 5% in situ emulsion polymerization PVAc wood adhesives. Effect on physical, thermal and mechanical properties was studied by viscosity, pH, contact angle measurement, differential scanning calorimetry (DSC) and pencil hardness test of films. Emulsions with different proportions of MCC were prepared and the shear strength of the applied adhesive on wood was measured. The viscosity of the adhesives was increased by increasing the concentration of MCC. The mechanical properties like tensile strength of adhesives with MCC were measured by universal tensile machine (UTM). Thermal stability was studied by differential scanning calorimetry (DSC). The tensile shear strength demonstrates that MCC can improve bonding strength as compared to PVAc Homo based adhesive in the wet condition which was validated through a contact angle study. The hardness of PVAc films were also changed positively by the addition of MCC. Here, we studied the effect of the addition of different concentrations of MCC materials in situ polymerization of PVAc on their performance properties.展开更多
Polyvinyl alcohol (PVA) stabilized Polyvinyl acetate (PVAc) dispersions-based wood adhesive has poor water and heat resistance. Recently, the addition of fillers in the wood adhesive is one of the most effective ways ...Polyvinyl alcohol (PVA) stabilized Polyvinyl acetate (PVAc) dispersions-based wood adhesive has poor water and heat resistance. Recently, the addition of fillers in the wood adhesive is one of the most effective ways to enhance the performance of PVAc wood adhesive. Inorganic fillers have unique characteristics to improve the performance of adhesive, such as small size, high surface energy and surface hardness. Hence, the present work investigates the applicability of calcium carbonate and clay incorporated 3% in situ emulsion polymerization PVAc wood adhesive. Effect on physical, thermal and mechanical properties was studied by viscosity, pH, contact angle measurement, differential scanning calorimetry (DSC) and pencil hardness test of films. Emulsions with 3% calcium carbonate and 3% clay were prepared and the shear strength of the applied adhesive on wood was measured. The viscosity of the adhesives was reduced in the case of the addition of calcium carbonate and increased in the case of clay. The mechanical properties like tensile strength of adhesives with calcium carbonate and clay were measured by a universal tensile machine (UTM). Thermal stability was studied by differential scanning calorimetry (DSC). The tensile shear strength demonstrates that clay can improve bonding strength as compared to calcium carbonate of PVAc adhesive in wet conditions. The hardness of PVAc films was also changed positively by the addition of calcium carbonate and clay. Thermal stability of PVAc was significantly improved as calcium carbonate and clay were added to PVAc. Here, we did a comparative study of the effect of the addition of calcium carbonate and clay filler materials in situ polymerization of PVAc on their different properties.展开更多
Because the large areas of Iran are on arid and semiarid belt of the world, it has many problems due to windstorms. Wind storms cause dust and haze due to a mass of fine sand or silt soil elevated in the atmosphere. I...Because the large areas of Iran are on arid and semiarid belt of the world, it has many problems due to windstorms. Wind storms cause dust and haze due to a mass of fine sand or silt soil elevated in the atmosphere. It makes heart disease-cardiovascular and respiratory and so is detrimental for the children. These have plagued the residents and so lives of them are disrupted every so often. In this research, the subject soil stabilization using adherence of poly vinyl acetate polymer as a way to reduce the production of dust is defined for prone area. In this paper, the effect of poly vinyl acetate polymer on silt soil has been studied. In this study the samples were uncompacted particles of soil with different amount of water-solvated polymer (0, 5, 10, 15, 20, 25, 30 grams per meter squared) poured over them. These samples are kept in experimental environment for 7 days. After ensuring complete dryness, their stabilities are tested against wind flow with 20 m/s speed. Results showed that adding more polymers to soil would considerably increase its particles’ stabilities. This stability is due to positive reaction of polymer with soil particles. The effect of this stability is maintained during sample drying time in the lab and the soil maintains its characteristics during testing. The best results are obtained for 20 grams polymer per meter squared, where caused an increase in stability to about 15 times that of the soil without polymer.展开更多
The global energy crisis and overconsumption of non-renewable resources have depleted natural resources, climatic changes with global warming, and rise in sea level. The research on alternate sources and chemicals has...The global energy crisis and overconsumption of non-renewable resources have depleted natural resources, climatic changes with global warming, and rise in sea level. The research on alternate sources and chemicals has resulted in the usage of green materials. These biomaterials are sustainable sources, biodegradable, and are abundant in nature. The replacement of petrochemicals with biopolymers has gained much importance in this aspect. Conventionally, polyvinyl alcohol is employed as a protective colloid in polyvinyl acetate adhesive. Polyvinyl alcohol has the limitation of petroleum origin, is replaced by biopolymers. Starch being a biopolymer, has gained interest in replacing polyvinyl alcohol as a stabilizer. Cellulose has a low cost, and the most abundant biomaterial finds application as a reinforcing agent in conventional adhesives. Exploring cellulose as a stabilizer for polyvinyl acetate emulsion polymerization with reinforcement has created potential applicability of cellulose in adhesives. Surface hydroxyl groups in cellulose act as sites for functionalization, making it material for the adhesive sector. This review paper aims to showcase biomaterials, namely starch, and cellulose, in the adhesive field. A detailed review of cellulose as functional filler for polyvinyl acetate emulsion adhesives has been explained.展开更多
Synthetic wood adhesives, consisting of urea-formaldehyde resins (UF), phenol-formaldehyde resins (PF), melamine-formaldehyde resins (MF), and polyurethane resins, are widely used. For UF and MF, most investigations a...Synthetic wood adhesives, consisting of urea-formaldehyde resins (UF), phenol-formaldehyde resins (PF), melamine-formaldehyde resins (MF), and polyurethane resins, are widely used. For UF and MF, most investigations are concerned with reducing free formaldehyde content;for PF, most studies focused on finding new alternative chemicals to replace phenol. These adhesives come under the Carcinogenic, Mutagenic, and Reprotoxic chemicals (CMR) category. Due to global energy issues and dependency on petroleum sources, the focus has shifted to look for alternative and renewable raw material sources for wood adhesives. Conventionally available wood adhesives are polyvinyl alcohol (PVA) stabilized, with drawbacks like poor water resistance, poor heat resistance, low-temperature workability, and it’s based on petroleum resources. Polyvinyl acetate (PVAc) is non-resistant to moisture polymer, and if such adhesive joints are exploited in a moist environment, its strength substantially decreases. Sufficiently moisture-resistant adhesive joints are obtained by modifying PVAc dispersion with special compounds like reactive comonomer, Silanes, and modified PVA. To improve the workability at low temperature, Vinyl acetate (VAc) is copolymerized with specific comonomers like butyl acetate without affecting the performance properties. Here, we aim to present an overview of the research trend of PVAc-based adhesives in the wood industry. The review summarizes the current state of research PVAc-based adhesives.展开更多
Global energy issues and the reliance on hydrocarbon resources have resulted in the reduction of petroleum sources, and the focus of the chemical industries has shifted to substitute raw material sources. The major ra...Global energy issues and the reliance on hydrocarbon resources have resulted in the reduction of petroleum sources, and the focus of the chemical industries has shifted to substitute raw material sources. The major raw materials used in wood adhesives, such as hydrocarbons like polyvinyl acetate, would be gradually replaced by renewable natural polymers. Currently, polyvinyl alcohol has the limitation of petroleum origin, which is non-economical and it will be replaced by biopolymers. Conventionally available wood adhesive emulsions are colloid-like polyvinyl alcohol stabilized. Starch, being a naturally available polymer, has gained interest from researchers for replacing polyvinyl alcohol as a stabilizer. New research on sustainable, economical, biodegradable, renewable, and environmentally friendly starch grafted polyvinyl acetate emulsion that was synthesized by the graft polymerization of vinyl acetate monomer onto starch. However, starch grafted polyvinyl acetate emulsion-based adhesive’s properties, such as poor water resistance, weak adhesion, delayed drying rate and delayed setting speed, have resulted in limitations in its application as a wood adhesive. A detailed review of starch grafting on vinyl acetate and comonomers like acrylamides, and acrylic acid, and the addition of nano-fillers to enhance the water resistance and performance properties of sustainable adhesives has been explained.展开更多
Carbon nanotube (CNT) has remarkable piezoresistive properties,which makes its extremely sensitive to the mechanical force. In this study,the CNT yarn with the strength of 90 MPa and the strain sensing gage factor of ...Carbon nanotube (CNT) has remarkable piezoresistive properties,which makes its extremely sensitive to the mechanical force. In this study,the CNT yarn with the strength of 90 MPa and the strain sensing gage factor of 1.75 was selected and embedded into the ethylene vinyl acetate (EVA) elastomer as a sensing material.By measuring the electric resistance changing under the stretching,bending,longitudinally and transversely compressing of the CNT embedded EVA, the resistance changing curves and their linear correlations were obtained and analyzed. The result shows that the gage factor under the tensile test is the highest( 2.51),which is higher than the original value of CNT yarn (1.75). The gage factors of the CNT yarn embedded into EVA elastomer under bending and longitudinal and transverse compression are 2.29,1.55 and 0.79,respectively.展开更多
Sepiolite (S9,B10,B20,B40) and boehmite have been added to an intumecent flame retardant (IFR) system to produce the halogen-free and fire-resistant ethylene-vinyl acetate copolymer (EVM) rubber. The rubber contains a...Sepiolite (S9,B10,B20,B40) and boehmite have been added to an intumecent flame retardant (IFR) system to produce the halogen-free and fire-resistant ethylene-vinyl acetate copolymer (EVM) rubber. The rubber contains ammonium polyphosphate (APP) as acid source,double pentaerythritol (D-PER) as carbon source and melamine (MN) as gas source. The effects of nano-filler sepiolite and boehmite on the fire-resistant property of EVM rubber based on IFR system were investigated. The test results show that the system with nano-filler of sepiolite B10 has the best fire-resistant property. The process of smoke emission and thermal decomposition,the element composition of char surface and the micro morphology of intumecent char layer of the EVM IFR system with nano-filler were also studied by NBS chamber,thermogravimetric (TG) analysis,X-ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM).展开更多
Conventionally available Polyvinyl acetate (PVAc) wood glues are polyvinyl alcohol (PVA) stabilized, with drawbacks like poor strength at high humidity, poor strength at high temperature and workability at low-tempera...Conventionally available Polyvinyl acetate (PVAc) wood glues are polyvinyl alcohol (PVA) stabilized, with drawbacks like poor strength at high humidity, poor strength at high temperature and workability at low-temperature. PVAc is non-resistant to high humidity, and if such adhesive bonds are exploited in a highly humid environment, its strength substantially decreases. Sufficiently water-resistant adhesive bonds are achieved by modifying PVAc dispersion with special chemicals like acrylic acid (AA) and N-methylol acrylamide (NMA) as a co-monomer, Silanes, and ethylene modified PVA. The Lewis acids like aluminium chloride and aluminium nitrate are used as cross-linkers. So PVAc adhesives are classified as reactive and non-reactive glue. Application of non-reactive D1 (as per EN 204-205) and reactive D2 and D3 (as per EN 204-205) adhesives for bonding laminate on plywood is a regular practice in the Indian market. In summer time, Crack formation was seen in laminate bonded with reactive D2 and D3 adhesives in regions where the room temperature was above 45°C. However, if the same laminate substrates were bonded with non-reactive D1, no cracks were seen. To analyse the above phenomenon, we have done Dynamic mechanical analysis of non-reactive D1, reactive D2 and D3 adhesive.展开更多
Graphite oxide, a pseudo-two-dimensional solid in bulk form, was synthesized from natural graphite powder byoxidization with KMnO<sub>4</sub> in concentrated H<sub>2</sub>SO<sub>4</sub...Graphite oxide, a pseudo-two-dimensional solid in bulk form, was synthesized from natural graphite powder byoxidization with KMnO<sub>4</sub> in concentrated H<sub>2</sub>SO<sub>4</sub>. The poly（vinyl acetate）-intercalated graphite oxide nano-composite wasprepared by an in situ intercalative polymerization reaction, in which n-octanol-graphite oxide intercalation compounds werefirst obtained, vinyl acetate monomer was then dispersed into the interlayer of modified graphite oxide, followed by thermalpolymerization of the monomer. It was experimentally shown that the c-axis space of poly（vinyl acetate）-intercalated graphiteoxide was increased to 0.115 nm, which suggested there existed a monolayer of poly（vinyl acetate） chain between the layersof graphite oxide. The nanocomposite was also characterized with thermal analysis and FT-IR spectrometry.展开更多
To overcome the fast or burst release of hydrophilic drugs from hydrophilic alginate-based carriers,hydrophobic molecule(vinyl acetate,VAc)was grafted on alginate(Alg),which was further used to prepare drug carriers.A...To overcome the fast or burst release of hydrophilic drugs from hydrophilic alginate-based carriers,hydrophobic molecule(vinyl acetate,VAc)was grafted on alginate(Alg),which was further used to prepare drug carriers.Amphiphilic Alg-g-PVAc hydrogel beads were firstly prepared by emulsification/internal gelation technique for the loading of bovine serum albumin(BSA).Then,chitosan was coated on the surface of beads to form novel amphiphilic Alg-g-PVAc/chitosan(Alg-g-PVAc/CS)microcapsules.The BSA-loading amphiphilic Alg-g-PVAc/chitosan(Alg-g-PVAc/CS)microcapsules display similar morphology and size to the hydrophilic alginate/chitosan(AC)microcapsules.However,the drug loading and loading efficiency of BSA in Alg-g-PVAc/CS microcapsules are higher,and the release rate of BSA from Alg-g-PVAc/CS microcapsules is slower.The results demonstrate that the introduction of hydrophobic PVAc on alginate can effectively help retard the release of BSA,and the higher degree of substitution is,the slower the release rate is.In addition,the complex membrane can also be adjusted to delay the release of BSA.As a whole,amphiphilic sodium alginate-vinyl acetate/CS microparticles could be developed for macromolecular drug delivery.展开更多
The copolymerization of maleic anhydride and vinyl acetate in tetrahydrofuran was studied. Results show that the maximum copolymerization rate is in 0.6 mole fraction of maleic anhydride, indicating the involvement of...The copolymerization of maleic anhydride and vinyl acetate in tetrahydrofuran was studied. Results show that the maximum copolymerization rate is in 0.6 mole fraction of maleic anhydride, indicating the involvement of maleic anhydride-tetrahydrofuran charge transfer complex in the chain initiation process. ESR study provides collateral evidence for the formation of maleic anhydride radical and tetrahydrofuran radical.展开更多
In this paper,blend membranes from polyvinyl acetate(PVAc)and block copolymer poly(amide-12-b-ethylene oxide)(Pebax1074)are prepared by solution casting and solvent evaporation method.Although they are homogeneous on ...In this paper,blend membranes from polyvinyl acetate(PVAc)and block copolymer poly(amide-12-b-ethylene oxide)(Pebax1074)are prepared by solution casting and solvent evaporation method.Although they are homogeneous on a macro-scale,the observations from DSC and SEM indicate micro-phase separation for PVAc/Pebax1074 blend membranes.With the increase of Pebax1074 content,gas permeabilities of CO2,H2,N2and CH4all increase greatly.PVAc/Pebax1074 blend membranes with high PVAc content are appropriate for CO2/CH4separation.The temperature dependence of gas permeability is divided into rubbery region and glassy region.The activation energies of permeation in rubbery region are smaller than those in glassy region,and they all decrease with increasing Pebax1074 content.For N2,H2and CH4,their gas permeation properties are mainly influenced by the dual-mode sorption and hydrostatic pressure effect.But for CO2,its permeability increases with the increase of pressure due to CO2-induced plasticization effect,which is more obvious for PVAc/Pebax1074 blend membranes with high PVAc content.展开更多
The discarded feathers / ethylene vinyl acetate copolymer( EVA) thermoplastic composite materials was obtained with discarded feathers as reinforced material and EVA powders as matrix material by hot pressing method. ...The discarded feathers / ethylene vinyl acetate copolymer( EVA) thermoplastic composite materials was obtained with discarded feathers as reinforced material and EVA powders as matrix material by hot pressing method. Sound absorption properties were studied by changing mass ratio of discarded feathers and EVA,thickness of composite materials,hot pressing pressure and hot pressing temperature. It was found that the sound absorption properties of composite materials were good when the mass ratio of discarded feathers and EVA was 1: 1,thickness of composite materials was 30 mm,hot pressing pressure was 8 MPa,and hot pressing temperature was 80 ℃. Under the optimum conditions,the effect of composite density on sound absorption property was analyzed. In a certain range,the sound absorption property was enhanced with the decrease of the composite density.When the composite density was 0. 1g /cm^3, the maximum absorption coefficient was 0.96. Finally,the capillary theory was used to calculate the maximum sound absorption coefficient of discarded feathers / EVA thermoplastic composite materials. The good agreements of experimental results and calculated results proved the validity of the theoretical models.展开更多
Binary monomers of maleic acid and vinyl acetate are grafted onto poly(vinylidene fluoride) (PVDF) powder by pre-irradiation induced graft polymerization technique in emulsion solution. The co-grafting of binary monom...Binary monomers of maleic acid and vinyl acetate are grafted onto poly(vinylidene fluoride) (PVDF) powder by pre-irradiation induced graft polymerization technique in emulsion solution. The co-grafting of binary monomers is successfully proved by FT-IR spectroscopy analysis. The influences of the absorbed dose, reaction temperature, reaction time, total concentration of monomers, and feed ratio of binary monomers on the degree of grafting are investigated. The thermal property of grafted PVDF powder was characterized by differential scanning calorimetry (DSC) and thermo-gravimetry analysis (TGA).展开更多
In the present paper a model equation for calculating the radical desorption rate constant,k<sub>0</sub>,in the emulsion polymerization of vinyl acetate was suggested and the various parameters forevaluati...In the present paper a model equation for calculating the radical desorption rate constant,k<sub>0</sub>,in the emulsion polymerization of vinyl acetate was suggested and the various parameters forevaluating k<sub>0</sub> were determined.Effects of reaction temperature,emulsifier concentration,initiator con-centration,monomer conversion and phase ratio on k<sub>0</sub> were studied.It indicates that the desorptionof radicals from latex particles to aqueous phase must be taken into account in the modelling ofemulsion polymerization for the monomers with higher hydrophilicity such as vinyl acetate.展开更多
The charge-transfer complex of maleic anhydride and vinyl acetate was copolymerized under UV light. The chain composition and structure of the copolymer were analyzed with conductometry and NMR, and the chain sequence...The charge-transfer complex of maleic anhydride and vinyl acetate was copolymerized under UV light. The chain composition and structure of the copolymer were analyzed with conductometry and NMR, and the chain sequence was determined as alternating. The copolymerization rates at different feed ratios, temperatures and in different solvents were investigated, giving evidence to the very active involvement of the CT complexes in the copolymerization. Terpolymerization with acrylonitrile also showed that the complex mechanism was a proper one for this system.展开更多
文摘The goal is to develop a hybrid IPN network of polyvinyl acetate (PVAc) and ethylene-vinyl acetate (VAE). In this research work, the vinyl acetate (VAc)/ VAE hybrid emulsion and polyvinyl acetate emulsion (PVAc) were effectively synthesized. Emulsions with various characteristics have been developed by adjusting the weight ratios between the vinyl acetate monomer and the VAE component. The impacts on the mechanical, thermal, and physical properties of the films were investigated using tests for pencil hardness, tensile shear strength, pH, contact angle measurement, differential scanning calorimetry (DSC), and viscosity. When 5.0 weight percent VAE was added, the tensile shear strength in dry conditions decreased by 18.75% after a 24-hour bonding period, the heat resistance decreased by 26.29% (as per WATT 91) and the tensile shear strength decreased by approximately 36.52% in wet conditions (per EN 204). The pristine sample’s results were also confirmed by the contact angle test. The interpenetrating network (IPN) formation in hybrid PVAc emulsion as primary bonds does not directly attach to PVAc and VAE chains. The addition of VAE reduced the mechanical properties (at dry conditions) and heat resistance as per WATT 91. Contact angle analysis demonstrated that PVAc adhesives containing VAE had increased water resistance when compared to conventional PVA stabilised PVAc homopolymer-based adhesives. When compared to virgin PVAc Homo, the water resistance of the PVAc emulsion polymerization was enhanced by the addition of VAE.
基金the National Natural Science Foundation of China (No.51673059)the Science and Technology Planning Project of Henan Province (No. 212102210636)the Opening Project of Jiangxi Province Key Laboratory of Polymer Micro/Nano Manufacturing and Devices (East China University of Technology)。
文摘Polyamide 6 (PA6) was employed as a charring agent of intumescent flame retardant (IFR) to improve the flame retardancy of ethylene-vinyl acetate copolymer (EVA). Different processing procedures were used to regulate the localization of IFR in the EVA matrix. Localizations in which IFR was dispersed in the PA6phase or in the EVA phase were prepared. The effect of the localization of IFR on the flame retardancy of EVA was investigated. The limited oxygen index (LOI), vertical burning (UL 94) and cone calorimeter test (CCT)showed that the localization of IFR in the EVA matrix exhibited a remarkable influence on the flame retardancy.Compared with EVA/IFR, a weak improvement in the flame retardancy was observed in the EVA/PA6/IFR blend withthe localization of IFR in the PA6 phase. When IFR was regulated from the PA6 phase to the EVA matrix,a remarkable increase in the flame retardancy was exhibited. The LOI was increased from 27.8%to 32.7%, and the UL 94 vertical rating was increased from V-2 to V-0. Moreover, an approximately 41.36%decrease in the peak heat release rate was exhibited. A continuous and compact intumescent charring layer that formed in the blends with the localization of IFR in the EVA matrix should be responsible for its excellent flame retardancy.
文摘Polyvinyl alcohol (PVA) colloid stabilized Polyvinyl acetate (PVAc) based wood adhesive has poor performance in highly humid conditions. Currently, the addition of natural fillers in the wood adhesive is one of the most effective ways to enhance the performance of PVAc wood adhesive in highly moist conditions. Microcrystalline cellulose (MCC) are strong renewable, bio-based material and has great potential in a reinforcement of the polymeric matrix. Hence, the present work investigates the applicability of microcrystalline cellulose incorporated 3% and 5% in situ emulsion polymerization PVAc wood adhesives. Effect on physical, thermal and mechanical properties was studied by viscosity, pH, contact angle measurement, differential scanning calorimetry (DSC) and pencil hardness test of films. Emulsions with different proportions of MCC were prepared and the shear strength of the applied adhesive on wood was measured. The viscosity of the adhesives was increased by increasing the concentration of MCC. The mechanical properties like tensile strength of adhesives with MCC were measured by universal tensile machine (UTM). Thermal stability was studied by differential scanning calorimetry (DSC). The tensile shear strength demonstrates that MCC can improve bonding strength as compared to PVAc Homo based adhesive in the wet condition which was validated through a contact angle study. The hardness of PVAc films were also changed positively by the addition of MCC. Here, we studied the effect of the addition of different concentrations of MCC materials in situ polymerization of PVAc on their performance properties.
文摘Polyvinyl alcohol (PVA) stabilized Polyvinyl acetate (PVAc) dispersions-based wood adhesive has poor water and heat resistance. Recently, the addition of fillers in the wood adhesive is one of the most effective ways to enhance the performance of PVAc wood adhesive. Inorganic fillers have unique characteristics to improve the performance of adhesive, such as small size, high surface energy and surface hardness. Hence, the present work investigates the applicability of calcium carbonate and clay incorporated 3% in situ emulsion polymerization PVAc wood adhesive. Effect on physical, thermal and mechanical properties was studied by viscosity, pH, contact angle measurement, differential scanning calorimetry (DSC) and pencil hardness test of films. Emulsions with 3% calcium carbonate and 3% clay were prepared and the shear strength of the applied adhesive on wood was measured. The viscosity of the adhesives was reduced in the case of the addition of calcium carbonate and increased in the case of clay. The mechanical properties like tensile strength of adhesives with calcium carbonate and clay were measured by a universal tensile machine (UTM). Thermal stability was studied by differential scanning calorimetry (DSC). The tensile shear strength demonstrates that clay can improve bonding strength as compared to calcium carbonate of PVAc adhesive in wet conditions. The hardness of PVAc films was also changed positively by the addition of calcium carbonate and clay. Thermal stability of PVAc was significantly improved as calcium carbonate and clay were added to PVAc. Here, we did a comparative study of the effect of the addition of calcium carbonate and clay filler materials in situ polymerization of PVAc on their different properties.
文摘Because the large areas of Iran are on arid and semiarid belt of the world, it has many problems due to windstorms. Wind storms cause dust and haze due to a mass of fine sand or silt soil elevated in the atmosphere. It makes heart disease-cardiovascular and respiratory and so is detrimental for the children. These have plagued the residents and so lives of them are disrupted every so often. In this research, the subject soil stabilization using adherence of poly vinyl acetate polymer as a way to reduce the production of dust is defined for prone area. In this paper, the effect of poly vinyl acetate polymer on silt soil has been studied. In this study the samples were uncompacted particles of soil with different amount of water-solvated polymer (0, 5, 10, 15, 20, 25, 30 grams per meter squared) poured over them. These samples are kept in experimental environment for 7 days. After ensuring complete dryness, their stabilities are tested against wind flow with 20 m/s speed. Results showed that adding more polymers to soil would considerably increase its particles’ stabilities. This stability is due to positive reaction of polymer with soil particles. The effect of this stability is maintained during sample drying time in the lab and the soil maintains its characteristics during testing. The best results are obtained for 20 grams polymer per meter squared, where caused an increase in stability to about 15 times that of the soil without polymer.
文摘The global energy crisis and overconsumption of non-renewable resources have depleted natural resources, climatic changes with global warming, and rise in sea level. The research on alternate sources and chemicals has resulted in the usage of green materials. These biomaterials are sustainable sources, biodegradable, and are abundant in nature. The replacement of petrochemicals with biopolymers has gained much importance in this aspect. Conventionally, polyvinyl alcohol is employed as a protective colloid in polyvinyl acetate adhesive. Polyvinyl alcohol has the limitation of petroleum origin, is replaced by biopolymers. Starch being a biopolymer, has gained interest in replacing polyvinyl alcohol as a stabilizer. Cellulose has a low cost, and the most abundant biomaterial finds application as a reinforcing agent in conventional adhesives. Exploring cellulose as a stabilizer for polyvinyl acetate emulsion polymerization with reinforcement has created potential applicability of cellulose in adhesives. Surface hydroxyl groups in cellulose act as sites for functionalization, making it material for the adhesive sector. This review paper aims to showcase biomaterials, namely starch, and cellulose, in the adhesive field. A detailed review of cellulose as functional filler for polyvinyl acetate emulsion adhesives has been explained.
文摘Synthetic wood adhesives, consisting of urea-formaldehyde resins (UF), phenol-formaldehyde resins (PF), melamine-formaldehyde resins (MF), and polyurethane resins, are widely used. For UF and MF, most investigations are concerned with reducing free formaldehyde content;for PF, most studies focused on finding new alternative chemicals to replace phenol. These adhesives come under the Carcinogenic, Mutagenic, and Reprotoxic chemicals (CMR) category. Due to global energy issues and dependency on petroleum sources, the focus has shifted to look for alternative and renewable raw material sources for wood adhesives. Conventionally available wood adhesives are polyvinyl alcohol (PVA) stabilized, with drawbacks like poor water resistance, poor heat resistance, low-temperature workability, and it’s based on petroleum resources. Polyvinyl acetate (PVAc) is non-resistant to moisture polymer, and if such adhesive joints are exploited in a moist environment, its strength substantially decreases. Sufficiently moisture-resistant adhesive joints are obtained by modifying PVAc dispersion with special compounds like reactive comonomer, Silanes, and modified PVA. To improve the workability at low temperature, Vinyl acetate (VAc) is copolymerized with specific comonomers like butyl acetate without affecting the performance properties. Here, we aim to present an overview of the research trend of PVAc-based adhesives in the wood industry. The review summarizes the current state of research PVAc-based adhesives.
文摘Global energy issues and the reliance on hydrocarbon resources have resulted in the reduction of petroleum sources, and the focus of the chemical industries has shifted to substitute raw material sources. The major raw materials used in wood adhesives, such as hydrocarbons like polyvinyl acetate, would be gradually replaced by renewable natural polymers. Currently, polyvinyl alcohol has the limitation of petroleum origin, which is non-economical and it will be replaced by biopolymers. Conventionally available wood adhesive emulsions are colloid-like polyvinyl alcohol stabilized. Starch, being a naturally available polymer, has gained interest from researchers for replacing polyvinyl alcohol as a stabilizer. New research on sustainable, economical, biodegradable, renewable, and environmentally friendly starch grafted polyvinyl acetate emulsion that was synthesized by the graft polymerization of vinyl acetate monomer onto starch. However, starch grafted polyvinyl acetate emulsion-based adhesive’s properties, such as poor water resistance, weak adhesion, delayed drying rate and delayed setting speed, have resulted in limitations in its application as a wood adhesive. A detailed review of starch grafting on vinyl acetate and comonomers like acrylamides, and acrylic acid, and the addition of nano-fillers to enhance the water resistance and performance properties of sustainable adhesives has been explained.
基金National Natural Science Foundations of China(Nos.51303025,51503120)Shanghai Science and Technology Committee,China(No.14YF1409600)+2 种基金Shanghai Municipal Education Commission,China(No.ZZgcd14016)Fundamental Research Funds for the Central Universities,ChinaDonghua University Distinguished Young Professor Program,China
文摘Carbon nanotube (CNT) has remarkable piezoresistive properties,which makes its extremely sensitive to the mechanical force. In this study,the CNT yarn with the strength of 90 MPa and the strain sensing gage factor of 1.75 was selected and embedded into the ethylene vinyl acetate (EVA) elastomer as a sensing material.By measuring the electric resistance changing under the stretching,bending,longitudinally and transversely compressing of the CNT embedded EVA, the resistance changing curves and their linear correlations were obtained and analyzed. The result shows that the gage factor under the tensile test is the highest( 2.51),which is higher than the original value of CNT yarn (1.75). The gage factors of the CNT yarn embedded into EVA elastomer under bending and longitudinal and transverse compression are 2.29,1.55 and 0.79,respectively.
基金Sponsored by Project in National Key Technology R&D Program(2006BAE03B05-2)
文摘Sepiolite (S9,B10,B20,B40) and boehmite have been added to an intumecent flame retardant (IFR) system to produce the halogen-free and fire-resistant ethylene-vinyl acetate copolymer (EVM) rubber. The rubber contains ammonium polyphosphate (APP) as acid source,double pentaerythritol (D-PER) as carbon source and melamine (MN) as gas source. The effects of nano-filler sepiolite and boehmite on the fire-resistant property of EVM rubber based on IFR system were investigated. The test results show that the system with nano-filler of sepiolite B10 has the best fire-resistant property. The process of smoke emission and thermal decomposition,the element composition of char surface and the micro morphology of intumecent char layer of the EVM IFR system with nano-filler were also studied by NBS chamber,thermogravimetric (TG) analysis,X-ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM).
文摘Conventionally available Polyvinyl acetate (PVAc) wood glues are polyvinyl alcohol (PVA) stabilized, with drawbacks like poor strength at high humidity, poor strength at high temperature and workability at low-temperature. PVAc is non-resistant to high humidity, and if such adhesive bonds are exploited in a highly humid environment, its strength substantially decreases. Sufficiently water-resistant adhesive bonds are achieved by modifying PVAc dispersion with special chemicals like acrylic acid (AA) and N-methylol acrylamide (NMA) as a co-monomer, Silanes, and ethylene modified PVA. The Lewis acids like aluminium chloride and aluminium nitrate are used as cross-linkers. So PVAc adhesives are classified as reactive and non-reactive glue. Application of non-reactive D1 (as per EN 204-205) and reactive D2 and D3 (as per EN 204-205) adhesives for bonding laminate on plywood is a regular practice in the Indian market. In summer time, Crack formation was seen in laminate bonded with reactive D2 and D3 adhesives in regions where the room temperature was above 45°C. However, if the same laminate substrates were bonded with non-reactive D1, no cracks were seen. To analyse the above phenomenon, we have done Dynamic mechanical analysis of non-reactive D1, reactive D2 and D3 adhesive.
基金Financial support from Key Project of The National Natural Science Foundation of China (No. 59836230) is gratefully acknowledged.
文摘Graphite oxide, a pseudo-two-dimensional solid in bulk form, was synthesized from natural graphite powder byoxidization with KMnO<sub>4</sub> in concentrated H<sub>2</sub>SO<sub>4</sub>. The poly（vinyl acetate）-intercalated graphite oxide nano-composite wasprepared by an in situ intercalative polymerization reaction, in which n-octanol-graphite oxide intercalation compounds werefirst obtained, vinyl acetate monomer was then dispersed into the interlayer of modified graphite oxide, followed by thermalpolymerization of the monomer. It was experimentally shown that the c-axis space of poly（vinyl acetate）-intercalated graphiteoxide was increased to 0.115 nm, which suggested there existed a monolayer of poly（vinyl acetate） chain between the layersof graphite oxide. The nanocomposite was also characterized with thermal analysis and FT-IR spectrometry.
基金Supported by the National Natural Science Foundation of China(No.21276033)the Open Foundation of the State Key Laboratory of Bioactive Seaweed Substances(Nos.SKL-BASS1711,SKL-BASS1707)the National Undergraduates Innovation and Entrepreneurship Training Program of China(No.201711258000001)
文摘To overcome the fast or burst release of hydrophilic drugs from hydrophilic alginate-based carriers,hydrophobic molecule(vinyl acetate,VAc)was grafted on alginate(Alg),which was further used to prepare drug carriers.Amphiphilic Alg-g-PVAc hydrogel beads were firstly prepared by emulsification/internal gelation technique for the loading of bovine serum albumin(BSA).Then,chitosan was coated on the surface of beads to form novel amphiphilic Alg-g-PVAc/chitosan(Alg-g-PVAc/CS)microcapsules.The BSA-loading amphiphilic Alg-g-PVAc/chitosan(Alg-g-PVAc/CS)microcapsules display similar morphology and size to the hydrophilic alginate/chitosan(AC)microcapsules.However,the drug loading and loading efficiency of BSA in Alg-g-PVAc/CS microcapsules are higher,and the release rate of BSA from Alg-g-PVAc/CS microcapsules is slower.The results demonstrate that the introduction of hydrophobic PVAc on alginate can effectively help retard the release of BSA,and the higher degree of substitution is,the slower the release rate is.In addition,the complex membrane can also be adjusted to delay the release of BSA.As a whole,amphiphilic sodium alginate-vinyl acetate/CS microparticles could be developed for macromolecular drug delivery.
基金Projects supported by the National Natural Science Foundation of China
文摘The copolymerization of maleic anhydride and vinyl acetate in tetrahydrofuran was studied. Results show that the maximum copolymerization rate is in 0.6 mole fraction of maleic anhydride, indicating the involvement of maleic anhydride-tetrahydrofuran charge transfer complex in the chain initiation process. ESR study provides collateral evidence for the formation of maleic anhydride radical and tetrahydrofuran radical.
基金supported by the National Science and Technology Planning Project (No.2011BAC08B00)the National High Technology Research and Development Program of China (863 Program)(No.2012AA03A611)
文摘In this paper,blend membranes from polyvinyl acetate(PVAc)and block copolymer poly(amide-12-b-ethylene oxide)(Pebax1074)are prepared by solution casting and solvent evaporation method.Although they are homogeneous on a macro-scale,the observations from DSC and SEM indicate micro-phase separation for PVAc/Pebax1074 blend membranes.With the increase of Pebax1074 content,gas permeabilities of CO2,H2,N2and CH4all increase greatly.PVAc/Pebax1074 blend membranes with high PVAc content are appropriate for CO2/CH4separation.The temperature dependence of gas permeability is divided into rubbery region and glassy region.The activation energies of permeation in rubbery region are smaller than those in glassy region,and they all decrease with increasing Pebax1074 content.For N2,H2and CH4,their gas permeation properties are mainly influenced by the dual-mode sorption and hydrostatic pressure effect.But for CO2,its permeability increases with the increase of pressure due to CO2-induced plasticization effect,which is more obvious for PVAc/Pebax1074 blend membranes with high PVAc content.
文摘The discarded feathers / ethylene vinyl acetate copolymer( EVA) thermoplastic composite materials was obtained with discarded feathers as reinforced material and EVA powders as matrix material by hot pressing method. Sound absorption properties were studied by changing mass ratio of discarded feathers and EVA,thickness of composite materials,hot pressing pressure and hot pressing temperature. It was found that the sound absorption properties of composite materials were good when the mass ratio of discarded feathers and EVA was 1: 1,thickness of composite materials was 30 mm,hot pressing pressure was 8 MPa,and hot pressing temperature was 80 ℃. Under the optimum conditions,the effect of composite density on sound absorption property was analyzed. In a certain range,the sound absorption property was enhanced with the decrease of the composite density.When the composite density was 0. 1g /cm^3, the maximum absorption coefficient was 0.96. Finally,the capillary theory was used to calculate the maximum sound absorption coefficient of discarded feathers / EVA thermoplastic composite materials. The good agreements of experimental results and calculated results proved the validity of the theoretical models.
基金Supported by National Natural Science Foundation of China (11175234, 11105210)Knowledge Innovation Program of Chinese Academy of Sciences (KJCX2-YW-N49, XDA02040300)Shanghai Municipal Commission for Science and Technology (10ZR1436700, 11ZR1445400)
文摘Binary monomers of maleic acid and vinyl acetate are grafted onto poly(vinylidene fluoride) (PVDF) powder by pre-irradiation induced graft polymerization technique in emulsion solution. The co-grafting of binary monomers is successfully proved by FT-IR spectroscopy analysis. The influences of the absorbed dose, reaction temperature, reaction time, total concentration of monomers, and feed ratio of binary monomers on the degree of grafting are investigated. The thermal property of grafted PVDF powder was characterized by differential scanning calorimetry (DSC) and thermo-gravimetry analysis (TGA).
基金Supported by the National Natural Science Foundation of China
文摘In the present paper a model equation for calculating the radical desorption rate constant,k<sub>0</sub>,in the emulsion polymerization of vinyl acetate was suggested and the various parameters forevaluating k<sub>0</sub> were determined.Effects of reaction temperature,emulsifier concentration,initiator con-centration,monomer conversion and phase ratio on k<sub>0</sub> were studied.It indicates that the desorptionof radicals from latex particles to aqueous phase must be taken into account in the modelling ofemulsion polymerization for the monomers with higher hydrophilicity such as vinyl acetate.
基金Projects supported by the Science Fund of the Chinese Academy of Sciences
文摘The charge-transfer complex of maleic anhydride and vinyl acetate was copolymerized under UV light. The chain composition and structure of the copolymer were analyzed with conductometry and NMR, and the chain sequence was determined as alternating. The copolymerization rates at different feed ratios, temperatures and in different solvents were investigated, giving evidence to the very active involvement of the CT complexes in the copolymerization. Terpolymerization with acrylonitrile also showed that the complex mechanism was a proper one for this system.
