In this communication, by means of stress relaxation experiments, the viscous stress at various strains during tensile deformation of oriented polyolefin samples including high density polyethylene （HDPE）, linear lo...In this communication, by means of stress relaxation experiments, the viscous stress at various strains during tensile deformation of oriented polyolefin samples including high density polyethylene （HDPE）, linear low density polyethylene （LLDPE） and isotactic polypropylene （iPP）, has been determined. The viscous stress in the oriented samples takes up to 50%-70% of the total stress, which is unusually high compared with their isotropic counterparts. The unusual high viscous stress was discussed based on mainly the existence of shish structure in oriented polyolefins, which could enhance the inter-lamella coupling significantly.展开更多
Analysing the influence mechanism of the riblet protrusion height on turbulent drag components is more beneficial in organising the vortical structure over the riblet surface.Therefore, the Large Eddy Simulation(LES) ...Analysing the influence mechanism of the riblet protrusion height on turbulent drag components is more beneficial in organising the vortical structure over the riblet surface.Therefore, the Large Eddy Simulation(LES) is used to investigate the vortex structure over the riblet surface with different protrusion heights. Then, the variations of Reynolds stress and viscous shear stress in a turbulent channel are analysed. As a result, the drag reduction rate increases from3.4% when the riblets are completely submerged in the turbulent boundary layer to 7.9% when the protrusion height is 11.2. Further analysis shows that the protrusion height affects the streamwise vortices and the normal diffusivity of spanwise and normal vortices, thus driving the variation of Reynolds stress. Compared with the smooth surface, the vorticity strength and the number of streamwise vortices are weakened near the wall but increase in the logarithmic layer with increased protrusion height. Meanwhile, the normal diffusivity of spanwise vorticity decreases with the increase of protrusion height, and the normal diffusivity of normal vorticity is the smallest when the protrusion height is 11.2. Moreover, the protrusion height affects the velocity gradient of the riblet tip and riblet valley, thus driving the variation of viscous shear stress. With the increase of protrusion height, the velocity gradient of the riblet tip increases dramatically but decreases in the riblet valley.展开更多
Conventional methods for measuring local shear stress on the wetted perimeter of open channels are related to the measurement of the very low velocity close to the boundary.Measuring near-zero velocity values with hig...Conventional methods for measuring local shear stress on the wetted perimeter of open channels are related to the measurement of the very low velocity close to the boundary.Measuring near-zero velocity values with high fluctuations has always been a difficult task for fluid flow near solid boundaries.To solve the observation problems,a new model was developed to estimate the distribution of boundary shear stress from the velocity distribution in open channels with different cross-sectional shapes.To estimate the shear stress at a point on the wetted perimeter by the model,the velocity must be measured at a point with a known normal distance to the boundary.The experimental work of some other researchers on channels with various cross-sectional shapes,including rectangular,trapezoidal,partially full circular,and compound shapes,was used to evaluate the performance of the proposed model.Optimized exponent coefficients for the model were found using the multivariate Newton method with the minimum of the mean absolute percentage error(MAPE)between the model and experimental data as the objective function.Subsequently,the calculated shear stress distributions along the wetted perimeter were compared with the experimental data.The most important advantage of the proposed model is its inherent simplicity.The mean MAPE value for the seven selected cross-sections was 6.9%.The best results were found in the cross-sections with less discontinuity of the wetted perimeter,including the compound,trapezoidal,and partially full circular pipes.In contrast,for the rectangular cross-section with an angle between the bed and walls of 90°,MAPE increased due to the large discontinuities.展开更多
Interactions between different scales in turbulence were studied starting from the incompressible Navier-Stokes equations. The integral and differential formulae of the short-range viscous stresses, which express the ...Interactions between different scales in turbulence were studied starting from the incompressible Navier-Stokes equations. The integral and differential formulae of the short-range viscous stresses, which express the short-range interactions between contiguous scales in turbulence,were given. A concept of the resonant-range interactions between extreme contiguous scales was introduced and the differential formula of the resonant-range viscous stresses was obtained. The short- and resonant-range viscous stresses were applied to deduce the large-eddy simulation (LES) equations as well as the multiscale equations, which are approximately closed and do not contain any empirical constants or relations. The properties and advantages of using the multiscale equations to compute turbulent flows were discussed. The short-range character of the interactions between the scales in turbulence means that the multiscale simulation is a very valuable technique for the calculation of turbulent flows. A few numerical examples were also given.展开更多
The latest geopotential model, EGM96, was employed to compute the free-air gravity anomaly, geoidal separation, the average density anomalies of the crust and the uppermost mantle, and the distribution pattern of the ...The latest geopotential model, EGM96, was employed to compute the free-air gravity anomaly, geoidal separation, the average density anomalies of the crust and the uppermost mantle, and the distribution pattern of the viscous stress exerted by mantle convection over Xinjiang and its neighboring areas. Based on these results and other data, we try to interpret the geodynamical features of the Tianshan orogen. Our research suggests that the Tianshan orogen is in a tectonic setting of compressive settling, driven by mantle convection. Under the effect of the compressive stress field, asymmetric in north-south direction, the Tianshan orogen upheaved quickly. The center of compressive stress field is in the south of the Tianshan, and the characteristic of stress field is favorable for the view point that the Tarim plat subducts beneath the Tianshan. The southern margin of the Juggar basin and the northern margin of the Tarim basin are two areas where the crust is of mass deficiency. We attribute the mass deficiency to the fact that the crust, in both the north and the south of the Tianshan is bent downwards under the compressive stress. Our research also indicates that the density distribution patterns in the deep of the eastern Tianshan are different from those in the middle and western Tianshan. It may be explained as the results from the east-west oriented distinction of the mantle convection.展开更多
The non-physiologic turbulent flows in centrifugal rotary blood pumps (RBPs) may result in complications such as the hemolysis and the platelet activation. Recent researches suggest that the turbulent viscous dissipat...The non-physiologic turbulent flows in centrifugal rotary blood pumps (RBPs) may result in complications such as the hemolysis and the platelet activation. Recent researches suggest that the turbulent viscous dissipation in the smallest eddies is the main factor of the blood trauma caused by the turbulent flow. The turbulent viscous shear stress (TVSS) was taken as the realistic physical force acting on the cells. However, limited by the temporal and spatial resolutions of the instrumentation currently available, very limited studies are available for the TVSS in the RBPs. In this paper, the large eddy particle image velocimetry (PIV) method is used to estimate the turbulent dissipation rate in the sub-grid scale, to investigate the effect of the TVSS on the blood trauma. Detailed flow characteristics, such as the relative velocity vectors, the estimated TVSS levels and the Kolmogorov length scales, are analyzed in three impeller phases at three constant flow rates (3 L/min, 5 L/min and 7 L/min). Over the measures range in this study, the maximum TVSS in the investigated RBP is lower than the reported critical value of stress. This study demonstrates that the large eddy PIV method is effective to evaluate the flow-dependent force on the cells. On the other hand, it is found that the TVSS is highly dependent on the flow behavior. Under severe off-design conditions, the complex flow characteristics, such as the flow separation and the vortical structures, will increase the TVSS. Thus, in order to reduce the hemolysis in the RBPs, the flow disturbance, induced by the departure of the incidence angle, should be avoided during the design of the RBPs.展开更多
Kelvin–Helmholtz(KH)instability is a fundamental fluid instability that widely exists in nature and engineering.To better understand the dynamic process of the KH instability,the influence of the tangential velocity ...Kelvin–Helmholtz(KH)instability is a fundamental fluid instability that widely exists in nature and engineering.To better understand the dynamic process of the KH instability,the influence of the tangential velocity on the compressible KH instability is investigated by using the discrete Boltzmann method based on the nonequilibrium statistical physics.Both hydrodynamic and thermodynamic nonequilibrium(TNE)effects are probed and analyzed.It is found that,on the whole,the global density gradients,the TNE strength and area firstly increase and decrease afterwards.Both the global density gradient and heat flux intensity in the vertical direction are almost constant in the initial stage before a vortex forms.Moreover,with the increase of the tangential velocity,the KH instability evolves faster,hence the global density gradients,the TNE strength and area increase in the initial stage and achieve their peak earlier,and their maxima are higher for a larger tangential velocity.Physically,there are several competitive mechanisms in the evolution of the KH instability.(i)The physical gradients increase and the TNE effects are strengthened as the interface is elongated.The local physical gradients decrease and the local TNE intensity is weakened on account of the dissipation and/or diffusion.(ii)The global heat flux intensity is promoted when the physical gradients increase.As the contact area expands,the heat exchange is enhanced and the global heat flux intensity increases.(iii)The global TNE intensity reduces with the decreasing of physical gradients and increase with the increasing of TNE area.(iv)The nonequilibrium area increases as the fluid interface is elongated and is widened because of the dissipation and/or diffusion.展开更多
基金This work was financially supported by the National Natural Science Foundation of China (Nos. 20404008, 50533050 and 20490220)This work was subsidized by the Special Funds for Major State Basic Research Projects of China (No. 2003CB615600).
文摘In this communication, by means of stress relaxation experiments, the viscous stress at various strains during tensile deformation of oriented polyolefin samples including high density polyethylene （HDPE）, linear low density polyethylene （LLDPE） and isotactic polypropylene （iPP）, has been determined. The viscous stress in the oriented samples takes up to 50%-70% of the total stress, which is unusually high compared with their isotropic counterparts. The unusual high viscous stress was discussed based on mainly the existence of shish structure in oriented polyolefins, which could enhance the inter-lamella coupling significantly.
基金the National Natural Science Foundation of China(No. 52176032)the Natural Science Foundation of Tianjin Municipal Science and Technology Commission, China(No. 22JCQNJC00050)the National Science and Technology Major Project, China(No.2017-Ⅱ-0005-0016)
文摘Analysing the influence mechanism of the riblet protrusion height on turbulent drag components is more beneficial in organising the vortical structure over the riblet surface.Therefore, the Large Eddy Simulation(LES) is used to investigate the vortex structure over the riblet surface with different protrusion heights. Then, the variations of Reynolds stress and viscous shear stress in a turbulent channel are analysed. As a result, the drag reduction rate increases from3.4% when the riblets are completely submerged in the turbulent boundary layer to 7.9% when the protrusion height is 11.2. Further analysis shows that the protrusion height affects the streamwise vortices and the normal diffusivity of spanwise and normal vortices, thus driving the variation of Reynolds stress. Compared with the smooth surface, the vorticity strength and the number of streamwise vortices are weakened near the wall but increase in the logarithmic layer with increased protrusion height. Meanwhile, the normal diffusivity of spanwise vorticity decreases with the increase of protrusion height, and the normal diffusivity of normal vorticity is the smallest when the protrusion height is 11.2. Moreover, the protrusion height affects the velocity gradient of the riblet tip and riblet valley, thus driving the variation of viscous shear stress. With the increase of protrusion height, the velocity gradient of the riblet tip increases dramatically but decreases in the riblet valley.
文摘Conventional methods for measuring local shear stress on the wetted perimeter of open channels are related to the measurement of the very low velocity close to the boundary.Measuring near-zero velocity values with high fluctuations has always been a difficult task for fluid flow near solid boundaries.To solve the observation problems,a new model was developed to estimate the distribution of boundary shear stress from the velocity distribution in open channels with different cross-sectional shapes.To estimate the shear stress at a point on the wetted perimeter by the model,the velocity must be measured at a point with a known normal distance to the boundary.The experimental work of some other researchers on channels with various cross-sectional shapes,including rectangular,trapezoidal,partially full circular,and compound shapes,was used to evaluate the performance of the proposed model.Optimized exponent coefficients for the model were found using the multivariate Newton method with the minimum of the mean absolute percentage error(MAPE)between the model and experimental data as the objective function.Subsequently,the calculated shear stress distributions along the wetted perimeter were compared with the experimental data.The most important advantage of the proposed model is its inherent simplicity.The mean MAPE value for the seven selected cross-sections was 6.9%.The best results were found in the cross-sections with less discontinuity of the wetted perimeter,including the compound,trapezoidal,and partially full circular pipes.In contrast,for the rectangular cross-section with an angle between the bed and walls of 90°,MAPE increased due to the large discontinuities.
文摘Interactions between different scales in turbulence were studied starting from the incompressible Navier-Stokes equations. The integral and differential formulae of the short-range viscous stresses, which express the short-range interactions between contiguous scales in turbulence,were given. A concept of the resonant-range interactions between extreme contiguous scales was introduced and the differential formula of the resonant-range viscous stresses was obtained. The short- and resonant-range viscous stresses were applied to deduce the large-eddy simulation (LES) equations as well as the multiscale equations, which are approximately closed and do not contain any empirical constants or relations. The properties and advantages of using the multiscale equations to compute turbulent flows were discussed. The short-range character of the interactions between the scales in turbulence means that the multiscale simulation is a very valuable technique for the calculation of turbulent flows. A few numerical examples were also given.
基金National 305 projection of Xinjiang Uygur Autonomous Region !(96-915-0703) Chinese Joint Seismological Science Foundation, b
文摘The latest geopotential model, EGM96, was employed to compute the free-air gravity anomaly, geoidal separation, the average density anomalies of the crust and the uppermost mantle, and the distribution pattern of the viscous stress exerted by mantle convection over Xinjiang and its neighboring areas. Based on these results and other data, we try to interpret the geodynamical features of the Tianshan orogen. Our research suggests that the Tianshan orogen is in a tectonic setting of compressive settling, driven by mantle convection. Under the effect of the compressive stress field, asymmetric in north-south direction, the Tianshan orogen upheaved quickly. The center of compressive stress field is in the south of the Tianshan, and the characteristic of stress field is favorable for the view point that the Tarim plat subducts beneath the Tianshan. The southern margin of the Juggar basin and the northern margin of the Tarim basin are two areas where the crust is of mass deficiency. We attribute the mass deficiency to the fact that the crust, in both the north and the south of the Tianshan is bent downwards under the compressive stress. Our research also indicates that the density distribution patterns in the deep of the eastern Tianshan are different from those in the middle and western Tianshan. It may be explained as the results from the east-west oriented distinction of the mantle convection.
基金Project supported by the National Natural Science Foundation of China(Grant No.51536008)the National Key R&D Program of China(Grant No.2018 YFB0606101).
文摘The non-physiologic turbulent flows in centrifugal rotary blood pumps (RBPs) may result in complications such as the hemolysis and the platelet activation. Recent researches suggest that the turbulent viscous dissipation in the smallest eddies is the main factor of the blood trauma caused by the turbulent flow. The turbulent viscous shear stress (TVSS) was taken as the realistic physical force acting on the cells. However, limited by the temporal and spatial resolutions of the instrumentation currently available, very limited studies are available for the TVSS in the RBPs. In this paper, the large eddy particle image velocimetry (PIV) method is used to estimate the turbulent dissipation rate in the sub-grid scale, to investigate the effect of the TVSS on the blood trauma. Detailed flow characteristics, such as the relative velocity vectors, the estimated TVSS levels and the Kolmogorov length scales, are analyzed in three impeller phases at three constant flow rates (3 L/min, 5 L/min and 7 L/min). Over the measures range in this study, the maximum TVSS in the investigated RBP is lower than the reported critical value of stress. This study demonstrates that the large eddy PIV method is effective to evaluate the flow-dependent force on the cells. On the other hand, it is found that the TVSS is highly dependent on the flow behavior. Under severe off-design conditions, the complex flow characteristics, such as the flow separation and the vortical structures, will increase the TVSS. Thus, in order to reduce the hemolysis in the RBPs, the flow disturbance, induced by the departure of the incidence angle, should be avoided during the design of the RBPs.
基金supported by the National Natural Science Foundation of China(Grant Nos.51806116 and 11875001)the Natural Science Foundation of Fujian Provinces(Grant Nos.2021J01652 and 2021J01655).
文摘Kelvin–Helmholtz(KH)instability is a fundamental fluid instability that widely exists in nature and engineering.To better understand the dynamic process of the KH instability,the influence of the tangential velocity on the compressible KH instability is investigated by using the discrete Boltzmann method based on the nonequilibrium statistical physics.Both hydrodynamic and thermodynamic nonequilibrium(TNE)effects are probed and analyzed.It is found that,on the whole,the global density gradients,the TNE strength and area firstly increase and decrease afterwards.Both the global density gradient and heat flux intensity in the vertical direction are almost constant in the initial stage before a vortex forms.Moreover,with the increase of the tangential velocity,the KH instability evolves faster,hence the global density gradients,the TNE strength and area increase in the initial stage and achieve their peak earlier,and their maxima are higher for a larger tangential velocity.Physically,there are several competitive mechanisms in the evolution of the KH instability.(i)The physical gradients increase and the TNE effects are strengthened as the interface is elongated.The local physical gradients decrease and the local TNE intensity is weakened on account of the dissipation and/or diffusion.(ii)The global heat flux intensity is promoted when the physical gradients increase.As the contact area expands,the heat exchange is enhanced and the global heat flux intensity increases.(iii)The global TNE intensity reduces with the decreasing of physical gradients and increase with the increasing of TNE area.(iv)The nonequilibrium area increases as the fluid interface is elongated and is widened because of the dissipation and/or diffusion.
