To improve the crack-resistance of the mould for silica sol bonded quartz based ceramic mould casting,aluminum silicate fibers with the diameter ranging from 5 μm to 25 μm and the length about 1 mm were dispersed in...To improve the crack-resistance of the mould for silica sol bonded quartz based ceramic mould casting,aluminum silicate fibers with the diameter ranging from 5 μm to 25 μm and the length about 1 mm were dispersed in the ceramic mould.The effect of the aluminum silicate fibers on the tensile strength,shrinkage rate and the cracking trend of the ceramic mould were investigated.In the ceramic slurry,quartz sand was applied as ceramic aggregate,silica sol containing 30% silicon dioxide as bonder,and the weight ratio of quartz sand to silica sol was 2.69;the dispersed fibers changed from 0 to 0.24vol.%.The mould samples were formed after the slurry was poured and gelled at room temperature,and then sintered at different temperatures ranging from 100 to 800 ℃ to measure the tensile strength and shrinkage rate.The results show that,with the aluminum silicate fiber addition increasing from 0 to 0.24vol.%,the tensile strength increases linearly from 0.175 MPa to 0.236 MPa,and the shrinkage rate decreases linearly from 1.75% to 1.68% for the ceramic mould sintered at 400 ℃,from 1.37% to 1.31% for the ceramic mould at room temperature.As the sintering temperature was raised from 100 ℃ to 800 ℃,the tensile strength increases,and the shrinkage rate decreases at all temperatures,compared with those without fiber dispersion,but their variation patterns remain the same.Furthermore,the cracking trend of the mould and its decreasing proportion were defined and analyzed quantitatively considering both effects of the fiber dispersion on the strength and shrinkage.The cracking trend appears to decrease linearly with increasing fiber content and to reach the maximum reduction of 28.8% when 0.24vol.% fiber was dispersed.Therefore,the investigation proposes a new method to improve the crack-resistance of the ceramic mould,i.e.,inorganic fiber dispersion into the ceramic mould.展开更多
The behavior and mechanism of Li leaching from lithium aluminum silicate glass-ceramics which can be used as a secondary source of Li using aqueous NaOH solution was investigated.The Li leaching efficiency is increase...The behavior and mechanism of Li leaching from lithium aluminum silicate glass-ceramics which can be used as a secondary source of Li using aqueous NaOH solution was investigated.The Li leaching efficiency is increased with increasing concentration of NaOH, specific surface area, and reaction temperature.When leached under optimum conditions, 2 mol/L NaOH, 53 μm particle undersize, 1:10 solid/liquid ratio, 250 r/min stirring speed, 100℃ reaction temperature, 12 hr, the Li leaching efficiency was approximately 70%.However, when the leaching experiment was performed for 48 hr, the concentration of Li+ ions contained in the leach liquor decreased from 1160 to 236 mg/L.To investigate the origin of this phenomenon, the obtained leach residue was analyzed by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy.These analyses show that zeolite was formed around the lithium aluminum silicate glass-ceramics, which affected the leaching of by adsorbing Li+ ions.In addition, using the shrinking-core model and the Arrhenius equation, the leaching reaction with NaOH was found to depends on the chemical reaction of the two reactants, with a higher than 41.84 kJ/mol of the activation energy.展开更多
The aragonite, an index mineral of glaucophane schist facies, has not been confirmed in the Dabie Mountains high pressure and ultrahigh pressure metamorphic belts. The Mulanshan glaucophane schist in Huangpi County,...The aragonite, an index mineral of glaucophane schist facies, has not been confirmed in the Dabie Mountains high pressure and ultrahigh pressure metamorphic belts. The Mulanshan glaucophane schist in Huangpi County, Hubei Province is located in the southwestern Dabie Mountains, Central China. The micron sized intergranular aragonite is confirmed with optical microscope (OM) and electron probe microanalysis (EPMA) in the glaucophane schist. The submicrometer sized ellipse aragonite inclusion is observed by using bright field image (BFI), X ray energy damage spectrograph (EDS) and selected area electron diffraction (SAED) with transmission electron microscope in the quartz lens of glaucophane albite epidote chlorite schist from Mulanshan. The presence of aragonite indicates not only the average geothermal gradient of the Mulanshan glaucophane schist less than 10 ℃/km, which is very close to that of eclogite in the Dabie Mountains metamorphic belts, but also the relatively higher concentration of CO2 during the metamorphic process. In addition, the glaucophane schist free of such index minerals as lawsonite, prehnite and pumpellyite, has been attributed to the effect of CO2 on the stability of calcium aluminum silicate minerals during the low grade metamorphism. EDS and SAED analysis results show that the host of aragonite inclusion is amorphous SiO2. The occurrence of amorphous SiO2 indicates a quick cooling process during the exhumation of the Mulanshan glaucophane schist. These results suggest that the rapid exhumation mechanism of the glaucophane schist, the same as that of eclogite in the Dabie Mountains metamorphic belts, occurred in the geodynamic context of subduction obduction.展开更多
In order to design a new technological process system to take the polymeric ferric aluminum silicate sulfate（PFASS） and to apply it in wastewater processing, the chemical composition analysis was carried on to the F...In order to design a new technological process system to take the polymeric ferric aluminum silicate sulfate（PFASS） and to apply it in wastewater processing, the chemical composition analysis was carried on to the Fuxin gangue, adopted the orthogonal experiment method to obtain optimum response condition of with the acid pickling taking the aluminum in the gangue and with alkali extracting taking the silicon in the gangue, The experiments indicate that the sample chemistry content which tests elect completely conform to the preparation inorganic polymer water treatment coagulant request standard. Used the polymeric ferric aluminum silicate sulfate results in which with the system take as the coagulant of treatment wastewater, used the mercerizing degree, the wastewater pH value, the coagulation time, the coagulant throws increment factors and so on to test and verify its influence on the waste water processing. The result indicates that by using this craft production PFASS in waste water processing, after the processed waste water achieves the emission standard, the processing effect is good.展开更多
Airborne silicate pollutants in flight corridors pose a serious threat to aviation safety whose severity is directly linked to the wettability of molten silicates on thermal barrier coatings(TBCs)at high temperatures(...Airborne silicate pollutants in flight corridors pose a serious threat to aviation safety whose severity is directly linked to the wettability of molten silicates on thermal barrier coatings(TBCs)at high temperatures(1200–2000℃).Despite its importance,the wettability of silicate melt on TBCs has not been well investigated.In particular,the surface morphology characteristics of TBCs can be expected to have a first-order effect on the wettability of silicate melt on such TBCs.Here,a series of atmospheric plasma spray(APS)yttria-stabilized zirconia(YSZ)TBCs with varying surface roughness were generated through the application of mechanical polishing.The metastable nonwetting behavior of three representative types of airborne silicate ash(volcanic ash,fly ash and a synthetic calcium–magnesium–aluminum–silicates(CMAS)powder)on these TBCs with varying surface roughness was investigated.It was observed that the smoother the surface of TBCs was,the larger the contact angle was with the molten silicate melts,and consequently,the smaller the area of damage was on the TBCs.Thus,the reduction in TBCs surface roughness(here via mechanical polishing)led to an improvement in the wetting and spreading resistance of TBCs to silicate melts at high temperature.In support of these observations and conclusions,the surface morphology of the TBC(both before and after polishing)had been characterized,and the mechanism of the surface roughness-dependence of wettability had been discussed.These results should contribute to reducing the deposition rate of silicate melt on TBCs,thus extending the lifetime of turbine blades and reducing maintenance costs.展开更多
文摘To improve the crack-resistance of the mould for silica sol bonded quartz based ceramic mould casting,aluminum silicate fibers with the diameter ranging from 5 μm to 25 μm and the length about 1 mm were dispersed in the ceramic mould.The effect of the aluminum silicate fibers on the tensile strength,shrinkage rate and the cracking trend of the ceramic mould were investigated.In the ceramic slurry,quartz sand was applied as ceramic aggregate,silica sol containing 30% silicon dioxide as bonder,and the weight ratio of quartz sand to silica sol was 2.69;the dispersed fibers changed from 0 to 0.24vol.%.The mould samples were formed after the slurry was poured and gelled at room temperature,and then sintered at different temperatures ranging from 100 to 800 ℃ to measure the tensile strength and shrinkage rate.The results show that,with the aluminum silicate fiber addition increasing from 0 to 0.24vol.%,the tensile strength increases linearly from 0.175 MPa to 0.236 MPa,and the shrinkage rate decreases linearly from 1.75% to 1.68% for the ceramic mould sintered at 400 ℃,from 1.37% to 1.31% for the ceramic mould at room temperature.As the sintering temperature was raised from 100 ℃ to 800 ℃,the tensile strength increases,and the shrinkage rate decreases at all temperatures,compared with those without fiber dispersion,but their variation patterns remain the same.Furthermore,the cracking trend of the mould and its decreasing proportion were defined and analyzed quantitatively considering both effects of the fiber dispersion on the strength and shrinkage.The cracking trend appears to decrease linearly with increasing fiber content and to reach the maximum reduction of 28.8% when 0.24vol.% fiber was dispersed.Therefore,the investigation proposes a new method to improve the crack-resistance of the ceramic mould,i.e.,inorganic fiber dispersion into the ceramic mould.
基金supported by the Technology Innovation Program(No.20003877,Development of eco-friendly electrochemical recycling system for production of high purity(>99.5)lithium and lithium compounds)funded By the Ministry of Trade,Industry&Energy(MOTIE,Korea)。
文摘The behavior and mechanism of Li leaching from lithium aluminum silicate glass-ceramics which can be used as a secondary source of Li using aqueous NaOH solution was investigated.The Li leaching efficiency is increased with increasing concentration of NaOH, specific surface area, and reaction temperature.When leached under optimum conditions, 2 mol/L NaOH, 53 μm particle undersize, 1:10 solid/liquid ratio, 250 r/min stirring speed, 100℃ reaction temperature, 12 hr, the Li leaching efficiency was approximately 70%.However, when the leaching experiment was performed for 48 hr, the concentration of Li+ ions contained in the leach liquor decreased from 1160 to 236 mg/L.To investigate the origin of this phenomenon, the obtained leach residue was analyzed by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy.These analyses show that zeolite was formed around the lithium aluminum silicate glass-ceramics, which affected the leaching of by adsorbing Li+ ions.In addition, using the shrinking-core model and the Arrhenius equation, the leaching reaction with NaOH was found to depends on the chemical reaction of the two reactants, with a higher than 41.84 kJ/mol of the activation energy.
基金theNationalNaturalScienceFoundationofChina (No .4980 2 0 0 4)
文摘The aragonite, an index mineral of glaucophane schist facies, has not been confirmed in the Dabie Mountains high pressure and ultrahigh pressure metamorphic belts. The Mulanshan glaucophane schist in Huangpi County, Hubei Province is located in the southwestern Dabie Mountains, Central China. The micron sized intergranular aragonite is confirmed with optical microscope (OM) and electron probe microanalysis (EPMA) in the glaucophane schist. The submicrometer sized ellipse aragonite inclusion is observed by using bright field image (BFI), X ray energy damage spectrograph (EDS) and selected area electron diffraction (SAED) with transmission electron microscope in the quartz lens of glaucophane albite epidote chlorite schist from Mulanshan. The presence of aragonite indicates not only the average geothermal gradient of the Mulanshan glaucophane schist less than 10 ℃/km, which is very close to that of eclogite in the Dabie Mountains metamorphic belts, but also the relatively higher concentration of CO2 during the metamorphic process. In addition, the glaucophane schist free of such index minerals as lawsonite, prehnite and pumpellyite, has been attributed to the effect of CO2 on the stability of calcium aluminum silicate minerals during the low grade metamorphism. EDS and SAED analysis results show that the host of aragonite inclusion is amorphous SiO2. The occurrence of amorphous SiO2 indicates a quick cooling process during the exhumation of the Mulanshan glaucophane schist. These results suggest that the rapid exhumation mechanism of the glaucophane schist, the same as that of eclogite in the Dabie Mountains metamorphic belts, occurred in the geodynamic context of subduction obduction.
文摘In order to design a new technological process system to take the polymeric ferric aluminum silicate sulfate（PFASS） and to apply it in wastewater processing, the chemical composition analysis was carried on to the Fuxin gangue, adopted the orthogonal experiment method to obtain optimum response condition of with the acid pickling taking the aluminum in the gangue and with alkali extracting taking the silicon in the gangue, The experiments indicate that the sample chemistry content which tests elect completely conform to the preparation inorganic polymer water treatment coagulant request standard. Used the polymeric ferric aluminum silicate sulfate results in which with the system take as the coagulant of treatment wastewater, used the mercerizing degree, the wastewater pH value, the coagulation time, the coagulant throws increment factors and so on to test and verify its influence on the waste water processing. The result indicates that by using this craft production PFASS in waste water processing, after the processed waste water achieves the emission standard, the processing effect is good.
基金This study was financially supported by the National Science and Technology Major Project(No.2017-VI-0010-0081)the Program of the Ministry of Education of China for Introducing Talents of Discipline to Universities(No.B17002)+2 种基金the National Natural Science Foundation of China(No.51901011)the“Freigeist”Fellowship of the Volkswagenstiftung on“Volcanic Ash Deposition in Jet Engines”(VADJEs,No.89705)China Scholarship Council(CSC).
文摘Airborne silicate pollutants in flight corridors pose a serious threat to aviation safety whose severity is directly linked to the wettability of molten silicates on thermal barrier coatings(TBCs)at high temperatures(1200–2000℃).Despite its importance,the wettability of silicate melt on TBCs has not been well investigated.In particular,the surface morphology characteristics of TBCs can be expected to have a first-order effect on the wettability of silicate melt on such TBCs.Here,a series of atmospheric plasma spray(APS)yttria-stabilized zirconia(YSZ)TBCs with varying surface roughness were generated through the application of mechanical polishing.The metastable nonwetting behavior of three representative types of airborne silicate ash(volcanic ash,fly ash and a synthetic calcium–magnesium–aluminum–silicates(CMAS)powder)on these TBCs with varying surface roughness was investigated.It was observed that the smoother the surface of TBCs was,the larger the contact angle was with the molten silicate melts,and consequently,the smaller the area of damage was on the TBCs.Thus,the reduction in TBCs surface roughness(here via mechanical polishing)led to an improvement in the wetting and spreading resistance of TBCs to silicate melts at high temperature.In support of these observations and conclusions,the surface morphology of the TBC(both before and after polishing)had been characterized,and the mechanism of the surface roughness-dependence of wettability had been discussed.These results should contribute to reducing the deposition rate of silicate melt on TBCs,thus extending the lifetime of turbine blades and reducing maintenance costs.
