Some amphoteric surfactants (N-Decyl-N-benzyl-N-methylglycine(AB) and N-Dodecyl-N-benzyl-N-methylglycine(CD) were prepared in the laboratory. The physicochemical chemical characteristics were investigated. The adsorpt...Some amphoteric surfactants (N-Decyl-N-benzyl-N-methylglycine(AB) and N-Dodecyl-N-benzyl-N-methylglycine(CD) were prepared in the laboratory. The physicochemical chemical characteristics were investigated. The adsorption behavior of these surfactants at oil/air interface was investigated by measuring the surface tension and interfacial tension as function of concentration. Surface properties, in particular the critical micelle concentration (CMC), the maximum surface excess (ΓCMC) and the minimum surface area (AMIN) were measured. It is found that the surface and thermodynamic properties of the prepared surfactants depend on their hydrocarbon chain length. Also it is found that there is a good relation between surface properties of the additive and their efficiency in depressing the pour point. The mechanism of the depressants action has been suggested according the adsorption of each additive. Adsorption of the additive on the surface of the wax particles inhibits their growth and alters the crystal habits through micelle core. As the results the surface and thermodynamic parameters confirm the suggested mechanism and the decreasing of pour point. This is resulted in a multilayer, more isotropic wax crystal, and thus only a fixed amount of wax separates at any given temperatures. The results were discussed in terms of adsorption isotherm.展开更多
The interaction of an amphoteric surfactant, N-12alkylbetaine, and an acid dye in aqueous solution was studied by spectrophotometry. The results of the experiments show that the particle of dye interacts with one or s...The interaction of an amphoteric surfactant, N-12alkylbetaine, and an acid dye in aqueous solution was studied by spectrophotometry. The results of the experiments show that the particle of dye interacts with one or several N-12alkylbetaine molecules when the concentration of the surfactant is less than the CMC. The aggregated dyes are disintegrated when the surfactant concentration is more than the CMC, and the individual dye ion interacts with the suffactant micelle.展开更多
Methylation of toluene over ZSM-5 zeolites modified by the introduction of Sr of 2.5%, 5%, and 10% by weight was studied. Experiments were performed in a fixed bed under the conditions of reaction temperatures between...Methylation of toluene over ZSM-5 zeolites modified by the introduction of Sr of 2.5%, 5%, and 10% by weight was studied. Experiments were performed in a fixed bed under the conditions of reaction temperatures between 300°C-500°C, liquid hour space velocity of 4 g toluene/h.g catalyst, methanol to toluene ratio 4:1, and 0.01% of N-Octyl-N-benzyl-N-methylglycine as emulsifier. Data for conversion of toluene and selectivity towards xylene isomers showed that 2.5% Sr/ZSM-5 catalyst has the highest conversion of toluene at 500°C, and the lowest p-xylene selectivity, while 10% Sr/ZSM-5 catalyst has the highest selectivity for p-xylene production. Nevertheless, the catalyst 2.5% Sr/ZSM-5 has the highest selectivity for m-xylene. The two catalysts 2.5% and 5% Sr/ZSM-5 give nearly the same selectivity for the three xylene isomers at all conversions obtained at the reaction conditions under study.展开更多
As PFOS, PFOA and their derivatives were banned according to the Stockholm Convention for their potential bioaccumulation and toxicity, people attempted to substitute the legacy fluorosurfactants with short-chain ones...As PFOS, PFOA and their derivatives were banned according to the Stockholm Convention for their potential bioaccumulation and toxicity, people attempted to substitute the legacy fluorosurfactants with short-chain ones. Although short-chain alternatives can alleviate bioaccumulation, surface activity was compromised. Fluorine industry kept seeking for effective solution. In this work, we prepared and investigated a series of fluoroether betaine surfactants for their surface activity and spreading property. The role of oxygen on surface activity was discussed. We found that insertion of oxygen atoms into fluorinated chain could increase hydrophobicity and thus enhance surface activity. The contribution of one oxygen is approximately half of that of a difluoromethylene group by experience. Moreover, introducing oxygen diversified the structure to fill in the gap of surface activity between short and long fluorosurfactants. In summary, this work provided basic knowledge for molecular design.展开更多
A core-shell composite consisting of ZSM-5 zeolite as the core and ordered mesoporous silica as the shell was prepared by a surfactant-controlled sol-gel process and using tetradecylamine(TDA) as the template and Tetr...A core-shell composite consisting of ZSM-5 zeolite as the core and ordered mesoporous silica as the shell was prepared by a surfactant-controlled sol-gel process and using tetradecylamine(TDA) as the template and Tetraethylorthosilicate(TEOS) as the silica precursor.The pores of the silica shell were found to be ordered and perpendicular to the crystal faces of the zeolite core.The thickness of the shell in the coreshell structured composite can be adjusted in the range of 20-90 nm,while the surface morphology and the pore size distribution were modified by changing the mass ratio of TEOS to zeolite.The composite molecular sieves have higher surface area for capturing molecules than ZSM-5,and with the increase of mesoporous shell layer,the ZSM-5@SiO_(2)-x composites show stronger adsorption capacity of butyraldehyde.However,when the shell thickness exceeds 90 nm,the adsorption capacity of butyraldehyde decreases instead.The composites have a huge potential for environmental applications.展开更多
While newer,more efficient Lithium-ion batteries(LIBs)and extinguishing agents have been developed to reduce the occurrence of thermal runaway accidents,there is still a scarcity of research focused on the application...While newer,more efficient Lithium-ion batteries(LIBs)and extinguishing agents have been developed to reduce the occurrence of thermal runaway accidents,there is still a scarcity of research focused on the application of surfactants in different LIBs extinguishing agents,particularly in terms of patented technologies.The aim of this review paper is to provide an overview of the technological progress of LIBs and LIBs extinguishing agents in terms of patents in Korea,Japan,Europe,the United States,China,etc.The initial part of this review paper is sort out LIBs technology development in different regions.In addition,to compare LIBs extinguishing agent progress and challenges of liquid,solid,combination of multiple,and microencapsulated.The subsequent section of this review focuses on an in-depth analysis dedicated to the efficiency and challenges faced by the surfactants corresponding design principles of LIBs extinguishing agents,such as nonionic and anionic surfactants.A total of 451,760 LIBs-related patent and 20 LIBs-fire-extinguishing agent-related patent were included in the analyses.The extinguishing effect,cooling performance,and anti-recombustion on different agents have been highlighted.After a comprehensive comparison of these agents,this review suggests that temperature-sensitive hydrogel extinguishing agent is ideal for the effective control of LIBs fire.The progress and challenges of surfactants have been extensively examined,focusing on key factors such as surface activity,thermal stability,foaming properties,environmental friendliness,and electrical conductivity.Moreover,it is crucial to emphasize that the selection of a suitable surfactant must align with the extinguishing strategy of the extinguishing agent for optimal firefighting effectiveness.展开更多
BACKGROUND Acute respiratory distress syndrome precipitates is widespread pulmonary injury in impacted individuals,the neonatal respiratory distress syndrome(NRDS),primarily observed in preterm infants,represents a pr...BACKGROUND Acute respiratory distress syndrome precipitates is widespread pulmonary injury in impacted individuals,the neonatal respiratory distress syndrome(NRDS),primarily observed in preterm infants,represents a prevalent critical condition in neonatal clinical settings.AIM To investigate the clinical efficacy of various ventilation strategies combined with pulmonary surfactant(PS)therapy in the treatment of NRDS.METHODS A total of 20 neonates diagnosed with respiratory distress syndrome,admitted between May 2021 and June 2022,were randomly assigned to either a research group or a control group.Neonates in the research group received treatment involving high-frequency oscillatory ventilation(HFOV)in conjunction with PS.In contrast,neonates in the control group were administered either controlled mechanical ventilation or synchronous intermittent mandatory ventilation,combined with PS.Arterial blood samples from the neonates in both groups were collected before treatment,as well as 6 h,12 h,24 h,and 48 h post-treatment.These samples underwent blood gas analysis,with measurements taken for pH value,partial pressures of oxygen(O_(2))and carbon dioxide.Concurrently,data was collected on the duration of ventilator use,length of hospitalization time,O_(2) treatment time,treatment outcomes,and complications of the ventilator.RESULTS From 6-48 h post-treatment,both groups demonstrated significant improvements in arterial blood pH and oxygen partial pressure,along with a significant decrease in carbon dioxide partial pressure compared to pre-treatment values(P<0.05).Although these changes progressed over time,there were no significant differences between the two groups(P>0.05).However,the research group had significantly lower X-ray scores,shorter hospitalization time,and less time on O_(2) therapy compared to the control group(P<0.05).Mortality rates were similar between the two groups(P>0.05),but the research group had a significantly lower incidence of complications(P<0.05).CONCLUSION The integration of HFOV combine with PS has proven to effectively expedite the treatment duration,decrease the occurrence of complications,and secure the therapeutic efficacy in managing NRDS.展开更多
Spontaneous imbibition is an important phenomenon in tight reservoirs.The existence of a large number of fractures and micro-nano pores is the key factor affecting the spontaneous imbibition of tight reservoirs.In thi...Spontaneous imbibition is an important phenomenon in tight reservoirs.The existence of a large number of fractures and micro-nano pores is the key factor affecting the spontaneous imbibition of tight reservoirs.In this study,based on high-pressure mercury injection and nuclear magnetic resonance experiments,the pore distribution of tight sandstone is described.The influence of fractures,core porosity and permeability,and surfactants on the spontaneous imbibition of tight sandstone are studied by physical fracturing,interfacial tension test,wettability test and imbibition experiments.The results show that:the pore radius of tight sandstone is concentrated in 0.01-1 mm.Fractures can effectively reduce the oil drop adsorption on the core surface,enhancing the imbibition recovery of the tight sandstone with an increase of about 10%.As the number of fractures increases,the number of oil droplets adsorbed on the core surface decrease and the imbibition rate increases.The imbibition recovery increases with the increase in pore connectivity,while the imbibition rate increases with the increases in core porosity and permeability.The surfactant can improve the core water wettability and reduce the oilwater interfacial tension,reducing the adsorption of oil droplets on the core surface,and improving the core imbibition recovery with an increase of about 15%.In a word,the existence of fractures and surfactants can enhance the pore connectivity of the reservoir,reduce the adsorption of oil droplets on the core surface,and improve the imbibition rate and recovery rate of the tight oil reservoir.展开更多
Since wolframite is usually associated with calcite,the separation and enrichment of wolframite by froth flotation remains a great challenge.Herein,a novel trisiloxane surfactant N-(2-aminoethyl)-3-ami nopropyltrisilo...Since wolframite is usually associated with calcite,the separation and enrichment of wolframite by froth flotation remains a great challenge.Herein,a novel trisiloxane surfactant N-(2-aminoethyl)-3-ami nopropyltrisiloxane(AATS)was successful synthesized,which was used for the separation of wolframite from calcite for the first time.The flotation separation performance of AATS was studied by flotation test,and its adsorption mechanism was explored based on contact angle,infrared spectrum analysis(FTIR),zeta potential and density functional theory(DFT)calculation.The results of microflotation test and binary mixed ore flotation test pointed that AATS had excellent selectivity and more prominent collection capacity for the flotation of wolframite when compared with industrial reagent sodium oleate(NaOL).The measurement results of contact angle proved that AATS improved the hydrophobicity of the wolframite surface.The highly selective adsorption mechanism of AATS surfactant on mineral surfaces were further researched and analyzed by FTIR and zeta potential.The results revealed that AATS surfactant had significant adsorption effect on wolframite,yet almost no adsorption on calcite.DFT calculation indicated that AATS produced electrostatic adsorption with wolframite surface through—N+H3 group.展开更多
Thermoelectrics are a promising solution to the recovery of some of the 60%of the worldwide energy wasted as heat.However,their conversion efficiency is low and the best performing materials are brittle,toxic,and made...Thermoelectrics are a promising solution to the recovery of some of the 60%of the worldwide energy wasted as heat.However,their conversion efficiency is low and the best performing materials are brittle,toxic,and made of expensive ceramics.The challenge in developing better performing materials is in disrupting the electrical vs thermal conductivity correlation,to achieve low thermal conductivity simultaneously with a high electrical conductivity.Carbon nanotubes allow for the decoupling of the electronic density of states from the phonon density of states and this paper shows that flexible,thin films of double-walled carbon nanotube(DWCNT)can form effective n-and p-doped semiconductors that can achieve a combined Seebeck coefficient of 157.6µV K^(−1),the highest reported for a single DWCNT device to date.This is achieved through selected surfactant doping,whose role is correlated with the length of the hydrocarbon chain of the hydrophobic tail group of the surfactant’s molecules.CNTs functionalized with Triton X-405 show the highest output power consisting of a single junction of p-and n-type thermoelectric elements,reaching as high as 67 nW for a 45 K temperature gradient.Thus enabling flexible,cheaper,and more efficient thermoelectric generators through the use of functionalized CNTs.展开更多
As a novel electric demulsification method,bidirectional pulsed electric field(BPEF)was employed to demulsify the surfactant stabilized oil-in-water(SSO/W)emulsion for oil/water separation in this work.The demulsifica...As a novel electric demulsification method,bidirectional pulsed electric field(BPEF)was employed to demulsify the surfactant stabilized oil-in-water(SSO/W)emulsion for oil/water separation in this work.The demulsification behavior,characteristics,and stages under BPEF were explored.It was discovered that BPEF drove SSO/W emulsion to move and form vortexes,during which the oil droplets aggregated and accumulated to generate an oil droplet layer(ODL).ODL subsequently transformed into a continuous oil layer(COL)leading to the demulsification and separation of SSO/W emulsion.The conversion rate of ODL to COL was defined and used to evaluate the demulsification process and reflect the coalescence ability and transformation efficiency of dispersed oil droplets into COL.Furthermore,the effects of BPEF voltage,frequency,duty cycle,ratio of pulse output time,and surfactant type and content on the demulsification performance were examined.The optimal values of BPEF parameters for demulsification operation were 400 V,25 Hz,50%,and 4:1.O/W emulsion containing anionic surfactant was apt to be demulsified by BPEF,nonionic surfactant took the second place and cationic surfactant was the most difficult.A high surfactant content was not conducive to the BPEF demulsification.This work is anticipated to provide useful guidance for oil/water separation and oil recovery from actual emulsified oily wastewater by BPEF.展开更多
Separators have been gaining increasing attention to improve the performance of lithium ion batteries(LIBs),especially for high safe and long cycle life.However,commercial polyolefin separators still face the problems...Separators have been gaining increasing attention to improve the performance of lithium ion batteries(LIBs),especially for high safe and long cycle life.However,commercial polyolefin separators still face the problems of rapid capacity decay and safety issues due to the poor wettability with electrolytes and low thermal stability.Herein,a novel composite separator is proposed by introducing a surfactant of sodium dodecyl thiosulfate(SDS)into the polytetrafluoroethylene(PTFE)substrate with the binder of polyacrylic acid(PAA)through the suction filtration method.The introduction of PAA/SDS enhances the adsorption energy between PTFE substrate and electrolyte through density functional theory calculations,which improves wettability and electrolyte uptake of the separator significantly.The asachieved composite separator enables the LIBs to own high Li^(+)conductivity(0.64×10^(-3)S cm^(-1))and Li^(+)transference number(0.63),further leading to a high capacity retention of 93.50%after 500 cycles at 1 C.In addition,the uniform and smooth surface morphology of Li metal employed the composite separator after cycling indicates that the lithium dendrites can be successfully inhibited.This work indicates a promising route for the preparation of a novel composite separator for high safe LIBs.展开更多
Surfactants were proposed to be added into magnesium sulfate solution to improve the leaching process of weathered crust elution-deposited rare earth ores(WREOs).Effects of surfactants and their concentration on the s...Surfactants were proposed to be added into magnesium sulfate solution to improve the leaching process of weathered crust elution-deposited rare earth ores(WREOs).Effects of surfactants and their concentration on the seepage of leaching solutions and the leaching efficiency of rare earth(RE)and aluminum(Al)were investigated,and the leaching kinetics,the mass transfer process,the adhesion work and the adhesion work reduction factor were analyzed to reveal its strengthening leaching mechanism.The results show that cetyltrimethylammonium bromide(CTAB)has a better strengthening effect on the leaching process than dodecyl trimethyl ammonium bromide(DTAB),sodium dodecyl sulfate(SDS),sodium oleate and oleic acid.In the presence of 0.04%CTAB in 0.2 mol/L solution,the permeability coefficient of WREOs increases from 0.945×10^(-5)to 1.640×10^(-5)cm·s^(-1),and the leaching efficiency of RE increases from 80%to 90%,confirming the promotion of surfactants on the leaching process of WREOs.Kinetic analysis shows that the leaching process conforms to the inner diffusion control model,and the leaching kinetics equations of RE and Al related to CTAB content are obtained.Mass transfer discussion shows a smaller height equivalent to theoretical plate(HETP)of RE and Al at CTAB content of 0.04%,suggesting the higher mass transfer efficiency here.According to the interfacial properties of leaching solutions,the calculated adhesion work and the adhesion work reduction factor further demonstrate the strengthening leaching effect of CTAB on the leaching process of WREOs.展开更多
Environment friendly and intelligent surfactants have attracted great attention in recent years.A bio-based CO_(2)responsive surfactant rosin acid dimaleimide choline(R-BMI-C)with an extremely rigid skeleton was prepa...Environment friendly and intelligent surfactants have attracted great attention in recent years.A bio-based CO_(2)responsive surfactant rosin acid dimaleimide choline(R-BMI-C)with an extremely rigid skeleton was prepared using rosin and choline as raw materials by Diels-Alder addition reaction and acid-base neutralization reactions.Its structure was confirmed by IR and^(1)H NMR spectra.The foams’properties of R-BMI-C could be adjusted by bubbling CO_(2)/N_(2)to change the structure of the surfactant.At pH 10.4,R-BMI-C forms an unstable foam with a half-life of 1.5 h.When the pH was reduced to 7.4 by bubbling CO_(2),R-BMI-C forms an extremely stable foam with a half-life of 336 h.The surfactant R-BMI-C changed from bola type to conventional type when bubbling CO_(2).And the internal aggregation structure of R-BMI-C aqueous solution changed from spherical micelles to laminar micelles according to the cryogenic-transmission electron microscope.We know that the lamellar structure tends to adsorb at the air/water interface or is trapped in the foam film,which slows down the foam coarsening and agglomeration process,resulting in a significant increase in foam stability.R-BMI-C could be used in oil extraction,fire-fighting and chemical decontamination due to its excellent foaming,stabilization and defoaming properties.展开更多
Carbon-based perovskite solar cells show great potential owing to their low-cost production and superior stability in ambient air.However,scaling up to high-efficiency carbon-based solar modules hinges on reliable dep...Carbon-based perovskite solar cells show great potential owing to their low-cost production and superior stability in ambient air.However,scaling up to high-efficiency carbon-based solar modules hinges on reliable deposition of uniform defect-free perovskite films over large areas,which is an unsettled but urgent issue.In this work,a long-chain gemini surfactant is introduced into perovskite precursor ink to enforce self-assembly into a network structure,considerably enhancing the coverage and smoothness of the perovskite films.The long gemini surfactant plays a distinctively synergistic role in perovskite film construction,crystallization kinetics modulation and defect passivation,leading to a certified record power conversion efficiency of 15.46%with Voc of 1.13 V and Jsc of 22.92 mA cm^(-2)for this type of modules.Importantly,all of the functional layers of the module are printed through a simple and high-speed(300 cm min^(-1))blade coating strategy in ambient atmosphere.These results mark a significant step toward the commercialization of all-printable carbon-based perovskite solar modules.展开更多
Nanocellulose,a natural polymeric nanomaterial,has attracted significant attention in enhanced oil recovery(EOR)applications due to its abundance,nanoscale,high oil-water interfacial adsorption ef-ficiency.In this stu...Nanocellulose,a natural polymeric nanomaterial,has attracted significant attention in enhanced oil recovery(EOR)applications due to its abundance,nanoscale,high oil-water interfacial adsorption ef-ficiency.In this study,surface-functionalized cellulose nanocrystals(SF-CNCs)were prepared via hy-drochloric acid hydrolysis and chemical modification,with adaptable nanosize and considerable dispersion stability in low-permeability reservoirs.The SF-CNCs were structurally characterized by FT-IR,Cryo-TEM,which have a diameter of 5-10 nm and a length of 100-200 nm.The SF-CNC dispersions possessed higher stability and stronger salt-tolerance than those of corresponding CNC dispersions,due to the strong hydrophilicity of the sulfonic acid group.It was synergistically used with a non-ionic surfactant(APG1214)to formulate a combined flooding system(0.1 wt%SF-CNC+0.2 wt%APG1214).The combined flooding system exhibits strong emulsification stability,low oil-water interfacial tension of o.03 mN/m,and the ability to alter the wettability for oil-wetting rocks.Furthermore,the combined system was_able to provide an optimum EOR efficiency of 20.2%in low-permeability cores with 30.13×10^(-3)μm^(2).Notably.it can enlarge the sweep volume and increase the displacement efficiency simultaneously.Overall,the newly formulated nanocellulose/surfactant combined system exhibits a remarkable EoR performance in low-permeability reservoirs.展开更多
Nitrite is a commonly used additive in cured foods and its sensitive detection is important to human health.In this work,a simple but sensitive electrochemical sensor for nitrite was developed.Conductive carbon black(...Nitrite is a commonly used additive in cured foods and its sensitive detection is important to human health.In this work,a simple but sensitive electrochemical sensor for nitrite was developed.Conductive carbon black(VXC-72R)functionalized with a cationic surfactant cetyltrimethylammonium bromide(CTAB)was used as an electrode material,and was coated on a glassy carbon electrode(GCE)to fabricate the electrochemical sensor(CTAB/VXC-72R/GCE)for nitrite.Zeta potential characterization and a series of electrochemical tests were carried out on several materials.It was found that the present sensor showed an enhanced sensitivity towards nitrite detection due to the enhanced surface positive charge revealed by the Zeta potential.Under optimal conditions,the ranges of good linear relationship between the peak current and the nitrite concentration were obtained to be 0.5-5.0μmol/L and 5.0-1087.0μmol/L with a lower detection limit of 0.30μmol/L.It was also successfully used for the determination of nitrite in cured food samples with excellent reproducibility,stability and selectivity.展开更多
The objective of this study is to analyze the effects of using surfactant(CTAB)and cellulose nanofibers(NFC)as an admixture in cement mortars.We examined composite properties as porosity,compression energy,thermal con...The objective of this study is to analyze the effects of using surfactant(CTAB)and cellulose nanofibers(NFC)as an admixture in cement mortars.We examined composite properties as porosity,compression energy,thermal conductivity and hydration.The results showed that with the addition of 0.7%by weight of NFC per emulsion in the presence of a cationic surfactant(CTAB).The new material produced presented a dry porosity between 4.7%and 4.4%,compressive strength between 9.8 and 22.9 MPa,and thermal conductivity between 0.95 and 2.25 W·m^(−1)·K^(−1).Thus we show better mechanical and thermal performance than that traditional Portland cement mortar with a density similar.In addition,the mortar made by emulsion of ordinary portland cement,cellulose nanofiber and organophilic clay(OC)treated with cetyltrimethylammonium bromide(CTAB)obtained has good resistance under high temperature and water,as well as excellent thermal insulation performance under high temperature and humidity conditions.This study verified that the presence of NFC promotes hydration,leading to the production of more calcium silicate and portlandite gel.展开更多
In this study,a novel absorpent(MSAR600℃)with a hydrophobic surface and hierarchical porous structure for the removal of kitchen oil was facilely fabricated from the macroalgae,laver(Porphyra haitanensis)by incorpor-...In this study,a novel absorpent(MSAR600℃)with a hydrophobic surface and hierarchical porous structure for the removal of kitchen oil was facilely fabricated from the macroalgae,laver(Porphyra haitanensis)by incorpor-ating high-temperature carbonization and alkyl polyglucosides(APG)and rhamnolipid(RL)surfactants modifi-cation.The characterization results showed MSAR600℃ possessed a louts-leaf-like papillae microstructure with high contact angle(137.5°),abundant porous structure with high specific surface area(23.4 m^(2)/g),and various oxygen-containing functional groups(-OH,C=O,C-O).Batch adsorption experiments were conducted to inves-tigate the effect of adsorption time,temperature,pH,and absorbent dose on kitchen oil adsorption performance.Then the practical application for the removal of kitchen oil using MSAR600℃ was also performed.The results showed that MSAR600℃ had a higher removal efficiency for kitchen oil(75.98%),compared with the commercial detergent(72.3%).This study demonstrates an example of fabricating a green tableware detergent for enhanced removal performance of kitchen oil.展开更多
Combining low salinity water (LSW) with surfactants has an enormous potential for enhancing oil recovery processes. However, there is no consensus about the mechanisms involved, in addition to the fact that several st...Combining low salinity water (LSW) with surfactants has an enormous potential for enhancing oil recovery processes. However, there is no consensus about the mechanisms involved, in addition to the fact that several studies have been conducted in model systems, while experiments with rocks and reservoir fluids are scarce. This study presents a core-flooding experiment of LSW injection, with and without surfactant, using the core and heavy oil samples obtained from a sandstone reservoir in southeastern Mexico. The effluents and the crude oil obtained at each stage were analyzed. The study was complemented by tomographic analysis. The results revealed that LSW injection and hybrid process with surfactants obtained an increase of 11.4 percentage points in recovery factor. Various phenomena were caused by LSW flooding, such as changes in wettability and pH, ion exchange, mineral dissolution, detachment of fines and modification of the hydrocarbon profile. In the surfactant flooding, the reduction of interfacial tension and alteration of wettability were the main mechanisms involved. The findings of this work also showed that the conditions believed to be necessary for enhanced oil recovery with LSW, such as the presence of kaolinite or high acid number oil, are not relevant.展开更多
文摘Some amphoteric surfactants (N-Decyl-N-benzyl-N-methylglycine(AB) and N-Dodecyl-N-benzyl-N-methylglycine(CD) were prepared in the laboratory. The physicochemical chemical characteristics were investigated. The adsorption behavior of these surfactants at oil/air interface was investigated by measuring the surface tension and interfacial tension as function of concentration. Surface properties, in particular the critical micelle concentration (CMC), the maximum surface excess (ΓCMC) and the minimum surface area (AMIN) were measured. It is found that the surface and thermodynamic properties of the prepared surfactants depend on their hydrocarbon chain length. Also it is found that there is a good relation between surface properties of the additive and their efficiency in depressing the pour point. The mechanism of the depressants action has been suggested according the adsorption of each additive. Adsorption of the additive on the surface of the wax particles inhibits their growth and alters the crystal habits through micelle core. As the results the surface and thermodynamic parameters confirm the suggested mechanism and the decreasing of pour point. This is resulted in a multilayer, more isotropic wax crystal, and thus only a fixed amount of wax separates at any given temperatures. The results were discussed in terms of adsorption isotherm.
文摘The interaction of an amphoteric surfactant, N-12alkylbetaine, and an acid dye in aqueous solution was studied by spectrophotometry. The results of the experiments show that the particle of dye interacts with one or several N-12alkylbetaine molecules when the concentration of the surfactant is less than the CMC. The aggregated dyes are disintegrated when the surfactant concentration is more than the CMC, and the individual dye ion interacts with the suffactant micelle.
文摘Methylation of toluene over ZSM-5 zeolites modified by the introduction of Sr of 2.5%, 5%, and 10% by weight was studied. Experiments were performed in a fixed bed under the conditions of reaction temperatures between 300°C-500°C, liquid hour space velocity of 4 g toluene/h.g catalyst, methanol to toluene ratio 4:1, and 0.01% of N-Octyl-N-benzyl-N-methylglycine as emulsifier. Data for conversion of toluene and selectivity towards xylene isomers showed that 2.5% Sr/ZSM-5 catalyst has the highest conversion of toluene at 500°C, and the lowest p-xylene selectivity, while 10% Sr/ZSM-5 catalyst has the highest selectivity for p-xylene production. Nevertheless, the catalyst 2.5% Sr/ZSM-5 has the highest selectivity for m-xylene. The two catalysts 2.5% and 5% Sr/ZSM-5 give nearly the same selectivity for the three xylene isomers at all conversions obtained at the reaction conditions under study.
基金Key Program of National Natural Science Foundation of China(No.21737004)the National Key Research and Development Program of China(No.2021YFF0701700)+1 种基金Science and Technology Department of Fujian Province(No.2020T3020)Science and Technology Bureau of Sanming City(No.2021-G-50)for financial support。
文摘As PFOS, PFOA and their derivatives were banned according to the Stockholm Convention for their potential bioaccumulation and toxicity, people attempted to substitute the legacy fluorosurfactants with short-chain ones. Although short-chain alternatives can alleviate bioaccumulation, surface activity was compromised. Fluorine industry kept seeking for effective solution. In this work, we prepared and investigated a series of fluoroether betaine surfactants for their surface activity and spreading property. The role of oxygen on surface activity was discussed. We found that insertion of oxygen atoms into fluorinated chain could increase hydrophobicity and thus enhance surface activity. The contribution of one oxygen is approximately half of that of a difluoromethylene group by experience. Moreover, introducing oxygen diversified the structure to fill in the gap of surface activity between short and long fluorosurfactants. In summary, this work provided basic knowledge for molecular design.
文摘A core-shell composite consisting of ZSM-5 zeolite as the core and ordered mesoporous silica as the shell was prepared by a surfactant-controlled sol-gel process and using tetradecylamine(TDA) as the template and Tetraethylorthosilicate(TEOS) as the silica precursor.The pores of the silica shell were found to be ordered and perpendicular to the crystal faces of the zeolite core.The thickness of the shell in the coreshell structured composite can be adjusted in the range of 20-90 nm,while the surface morphology and the pore size distribution were modified by changing the mass ratio of TEOS to zeolite.The composite molecular sieves have higher surface area for capturing molecules than ZSM-5,and with the increase of mesoporous shell layer,the ZSM-5@SiO_(2)-x composites show stronger adsorption capacity of butyraldehyde.However,when the shell thickness exceeds 90 nm,the adsorption capacity of butyraldehyde decreases instead.The composites have a huge potential for environmental applications.
基金supported by the National Key Research and Development Program of China (No.2017YFC0804700)the Opening Project of State Key Laboratory of Explosion Science and Technology,Beijing Institute of Technology (No.KFJJ23-23M)。
文摘While newer,more efficient Lithium-ion batteries(LIBs)and extinguishing agents have been developed to reduce the occurrence of thermal runaway accidents,there is still a scarcity of research focused on the application of surfactants in different LIBs extinguishing agents,particularly in terms of patented technologies.The aim of this review paper is to provide an overview of the technological progress of LIBs and LIBs extinguishing agents in terms of patents in Korea,Japan,Europe,the United States,China,etc.The initial part of this review paper is sort out LIBs technology development in different regions.In addition,to compare LIBs extinguishing agent progress and challenges of liquid,solid,combination of multiple,and microencapsulated.The subsequent section of this review focuses on an in-depth analysis dedicated to the efficiency and challenges faced by the surfactants corresponding design principles of LIBs extinguishing agents,such as nonionic and anionic surfactants.A total of 451,760 LIBs-related patent and 20 LIBs-fire-extinguishing agent-related patent were included in the analyses.The extinguishing effect,cooling performance,and anti-recombustion on different agents have been highlighted.After a comprehensive comparison of these agents,this review suggests that temperature-sensitive hydrogel extinguishing agent is ideal for the effective control of LIBs fire.The progress and challenges of surfactants have been extensively examined,focusing on key factors such as surface activity,thermal stability,foaming properties,environmental friendliness,and electrical conductivity.Moreover,it is crucial to emphasize that the selection of a suitable surfactant must align with the extinguishing strategy of the extinguishing agent for optimal firefighting effectiveness.
文摘BACKGROUND Acute respiratory distress syndrome precipitates is widespread pulmonary injury in impacted individuals,the neonatal respiratory distress syndrome(NRDS),primarily observed in preterm infants,represents a prevalent critical condition in neonatal clinical settings.AIM To investigate the clinical efficacy of various ventilation strategies combined with pulmonary surfactant(PS)therapy in the treatment of NRDS.METHODS A total of 20 neonates diagnosed with respiratory distress syndrome,admitted between May 2021 and June 2022,were randomly assigned to either a research group or a control group.Neonates in the research group received treatment involving high-frequency oscillatory ventilation(HFOV)in conjunction with PS.In contrast,neonates in the control group were administered either controlled mechanical ventilation or synchronous intermittent mandatory ventilation,combined with PS.Arterial blood samples from the neonates in both groups were collected before treatment,as well as 6 h,12 h,24 h,and 48 h post-treatment.These samples underwent blood gas analysis,with measurements taken for pH value,partial pressures of oxygen(O_(2))and carbon dioxide.Concurrently,data was collected on the duration of ventilator use,length of hospitalization time,O_(2) treatment time,treatment outcomes,and complications of the ventilator.RESULTS From 6-48 h post-treatment,both groups demonstrated significant improvements in arterial blood pH and oxygen partial pressure,along with a significant decrease in carbon dioxide partial pressure compared to pre-treatment values(P<0.05).Although these changes progressed over time,there were no significant differences between the two groups(P>0.05).However,the research group had significantly lower X-ray scores,shorter hospitalization time,and less time on O_(2) therapy compared to the control group(P<0.05).Mortality rates were similar between the two groups(P>0.05),but the research group had a significantly lower incidence of complications(P<0.05).CONCLUSION The integration of HFOV combine with PS has proven to effectively expedite the treatment duration,decrease the occurrence of complications,and secure the therapeutic efficacy in managing NRDS.
基金This work was supported by the National Natural Science Foundation of China(No.51874320).
文摘Spontaneous imbibition is an important phenomenon in tight reservoirs.The existence of a large number of fractures and micro-nano pores is the key factor affecting the spontaneous imbibition of tight reservoirs.In this study,based on high-pressure mercury injection and nuclear magnetic resonance experiments,the pore distribution of tight sandstone is described.The influence of fractures,core porosity and permeability,and surfactants on the spontaneous imbibition of tight sandstone are studied by physical fracturing,interfacial tension test,wettability test and imbibition experiments.The results show that:the pore radius of tight sandstone is concentrated in 0.01-1 mm.Fractures can effectively reduce the oil drop adsorption on the core surface,enhancing the imbibition recovery of the tight sandstone with an increase of about 10%.As the number of fractures increases,the number of oil droplets adsorbed on the core surface decrease and the imbibition rate increases.The imbibition recovery increases with the increase in pore connectivity,while the imbibition rate increases with the increases in core porosity and permeability.The surfactant can improve the core water wettability and reduce the oilwater interfacial tension,reducing the adsorption of oil droplets on the core surface,and improving the core imbibition recovery with an increase of about 15%.In a word,the existence of fractures and surfactants can enhance the pore connectivity of the reservoir,reduce the adsorption of oil droplets on the core surface,and improve the imbibition rate and recovery rate of the tight oil reservoir.
基金This work was supported by the Natural Science Foundation of Jiangxi,China(Nos.20202ACBL213008 and 20202ZDB01005)。
文摘Since wolframite is usually associated with calcite,the separation and enrichment of wolframite by froth flotation remains a great challenge.Herein,a novel trisiloxane surfactant N-(2-aminoethyl)-3-ami nopropyltrisiloxane(AATS)was successful synthesized,which was used for the separation of wolframite from calcite for the first time.The flotation separation performance of AATS was studied by flotation test,and its adsorption mechanism was explored based on contact angle,infrared spectrum analysis(FTIR),zeta potential and density functional theory(DFT)calculation.The results of microflotation test and binary mixed ore flotation test pointed that AATS had excellent selectivity and more prominent collection capacity for the flotation of wolframite when compared with industrial reagent sodium oleate(NaOL).The measurement results of contact angle proved that AATS improved the hydrophobicity of the wolframite surface.The highly selective adsorption mechanism of AATS surfactant on mineral surfaces were further researched and analyzed by FTIR and zeta potential.The results revealed that AATS surfactant had significant adsorption effect on wolframite,yet almost no adsorption on calcite.DFT calculation indicated that AATS produced electrostatic adsorption with wolframite surface through—N+H3 group.
文摘Thermoelectrics are a promising solution to the recovery of some of the 60%of the worldwide energy wasted as heat.However,their conversion efficiency is low and the best performing materials are brittle,toxic,and made of expensive ceramics.The challenge in developing better performing materials is in disrupting the electrical vs thermal conductivity correlation,to achieve low thermal conductivity simultaneously with a high electrical conductivity.Carbon nanotubes allow for the decoupling of the electronic density of states from the phonon density of states and this paper shows that flexible,thin films of double-walled carbon nanotube(DWCNT)can form effective n-and p-doped semiconductors that can achieve a combined Seebeck coefficient of 157.6µV K^(−1),the highest reported for a single DWCNT device to date.This is achieved through selected surfactant doping,whose role is correlated with the length of the hydrocarbon chain of the hydrophobic tail group of the surfactant’s molecules.CNTs functionalized with Triton X-405 show the highest output power consisting of a single junction of p-and n-type thermoelectric elements,reaching as high as 67 nW for a 45 K temperature gradient.Thus enabling flexible,cheaper,and more efficient thermoelectric generators through the use of functionalized CNTs.
基金Scientific Platform Project of the Ministry of Education(fykf201907)the Postdoctoral Science Foundation Project of the Natural Science Foundation of Chongqing Municipality(cstc2021jcyjbshX0194)+3 种基金Science and Technology Research Program of Chongqing Municipal Education Commission(KJQN202100820 and KJZD-K201900804)Science and Technology Innovation Project of the Construction of the Chengdu-Chongqing Economic Circle of Chongqing Municipal Education Commission(KJCX2020036)Scientific Research Project of Chongqing Technology and Business University(2152016 and 2056006)Chongqing Technical Innovation and Application Project(cstc2019jscx-msxmX0275).
文摘As a novel electric demulsification method,bidirectional pulsed electric field(BPEF)was employed to demulsify the surfactant stabilized oil-in-water(SSO/W)emulsion for oil/water separation in this work.The demulsification behavior,characteristics,and stages under BPEF were explored.It was discovered that BPEF drove SSO/W emulsion to move and form vortexes,during which the oil droplets aggregated and accumulated to generate an oil droplet layer(ODL).ODL subsequently transformed into a continuous oil layer(COL)leading to the demulsification and separation of SSO/W emulsion.The conversion rate of ODL to COL was defined and used to evaluate the demulsification process and reflect the coalescence ability and transformation efficiency of dispersed oil droplets into COL.Furthermore,the effects of BPEF voltage,frequency,duty cycle,ratio of pulse output time,and surfactant type and content on the demulsification performance were examined.The optimal values of BPEF parameters for demulsification operation were 400 V,25 Hz,50%,and 4:1.O/W emulsion containing anionic surfactant was apt to be demulsified by BPEF,nonionic surfactant took the second place and cationic surfactant was the most difficult.A high surfactant content was not conducive to the BPEF demulsification.This work is anticipated to provide useful guidance for oil/water separation and oil recovery from actual emulsified oily wastewater by BPEF.
基金supported by the Science Foundation of the National Key Laboratory of Science and Technology on Advanced Composites in Special Environmentsthe National Natural Science Foundation of China(12002109)+1 种基金the China Postdoctoral Science Foundation(2020M670898)the Heilongjiang Postdoctoral Fund(LBH-Z20060)。
文摘Separators have been gaining increasing attention to improve the performance of lithium ion batteries(LIBs),especially for high safe and long cycle life.However,commercial polyolefin separators still face the problems of rapid capacity decay and safety issues due to the poor wettability with electrolytes and low thermal stability.Herein,a novel composite separator is proposed by introducing a surfactant of sodium dodecyl thiosulfate(SDS)into the polytetrafluoroethylene(PTFE)substrate with the binder of polyacrylic acid(PAA)through the suction filtration method.The introduction of PAA/SDS enhances the adsorption energy between PTFE substrate and electrolyte through density functional theory calculations,which improves wettability and electrolyte uptake of the separator significantly.The asachieved composite separator enables the LIBs to own high Li^(+)conductivity(0.64×10^(-3)S cm^(-1))and Li^(+)transference number(0.63),further leading to a high capacity retention of 93.50%after 500 cycles at 1 C.In addition,the uniform and smooth surface morphology of Li metal employed the composite separator after cycling indicates that the lithium dendrites can be successfully inhibited.This work indicates a promising route for the preparation of a novel composite separator for high safe LIBs.
基金Financial supports for this work from National Natural Science Foundation of China(Nos.22078252 and 52274266)the Graduate Education Innovation Foundation of Wuhan Institute of Technology(No.CX2021463)the Young Top-notch Talent Cultivation Program of Hubei Province are greatly appreciated.
文摘Surfactants were proposed to be added into magnesium sulfate solution to improve the leaching process of weathered crust elution-deposited rare earth ores(WREOs).Effects of surfactants and their concentration on the seepage of leaching solutions and the leaching efficiency of rare earth(RE)and aluminum(Al)were investigated,and the leaching kinetics,the mass transfer process,the adhesion work and the adhesion work reduction factor were analyzed to reveal its strengthening leaching mechanism.The results show that cetyltrimethylammonium bromide(CTAB)has a better strengthening effect on the leaching process than dodecyl trimethyl ammonium bromide(DTAB),sodium dodecyl sulfate(SDS),sodium oleate and oleic acid.In the presence of 0.04%CTAB in 0.2 mol/L solution,the permeability coefficient of WREOs increases from 0.945×10^(-5)to 1.640×10^(-5)cm·s^(-1),and the leaching efficiency of RE increases from 80%to 90%,confirming the promotion of surfactants on the leaching process of WREOs.Kinetic analysis shows that the leaching process conforms to the inner diffusion control model,and the leaching kinetics equations of RE and Al related to CTAB content are obtained.Mass transfer discussion shows a smaller height equivalent to theoretical plate(HETP)of RE and Al at CTAB content of 0.04%,suggesting the higher mass transfer efficiency here.According to the interfacial properties of leaching solutions,the calculated adhesion work and the adhesion work reduction factor further demonstrate the strengthening leaching effect of CTAB on the leaching process of WREOs.
基金supported by the National Natural Science Foundation of China(32171734)the Scientific Research Funds of Huaqiao University(20BS201).
文摘Environment friendly and intelligent surfactants have attracted great attention in recent years.A bio-based CO_(2)responsive surfactant rosin acid dimaleimide choline(R-BMI-C)with an extremely rigid skeleton was prepared using rosin and choline as raw materials by Diels-Alder addition reaction and acid-base neutralization reactions.Its structure was confirmed by IR and^(1)H NMR spectra.The foams’properties of R-BMI-C could be adjusted by bubbling CO_(2)/N_(2)to change the structure of the surfactant.At pH 10.4,R-BMI-C forms an unstable foam with a half-life of 1.5 h.When the pH was reduced to 7.4 by bubbling CO_(2),R-BMI-C forms an extremely stable foam with a half-life of 336 h.The surfactant R-BMI-C changed from bola type to conventional type when bubbling CO_(2).And the internal aggregation structure of R-BMI-C aqueous solution changed from spherical micelles to laminar micelles according to the cryogenic-transmission electron microscope.We know that the lamellar structure tends to adsorb at the air/water interface or is trapped in the foam film,which slows down the foam coarsening and agglomeration process,resulting in a significant increase in foam stability.R-BMI-C could be used in oil extraction,fire-fighting and chemical decontamination due to its excellent foaming,stabilization and defoaming properties.
基金supported by the National Natural Science Foundation of China(U2001217,22261160370 and 21972006)Guangdong-Hong Kong-Macao Joint Innovation Foundation(2021A0505110003)+1 种基金Shenzhen Basic Research(JCYJ20220818101018038 and JCYJ20200109110628172)Guangdong Province Regional Joint Innovation Foundation(2020B1515120039)。
文摘Carbon-based perovskite solar cells show great potential owing to their low-cost production and superior stability in ambient air.However,scaling up to high-efficiency carbon-based solar modules hinges on reliable deposition of uniform defect-free perovskite films over large areas,which is an unsettled but urgent issue.In this work,a long-chain gemini surfactant is introduced into perovskite precursor ink to enforce self-assembly into a network structure,considerably enhancing the coverage and smoothness of the perovskite films.The long gemini surfactant plays a distinctively synergistic role in perovskite film construction,crystallization kinetics modulation and defect passivation,leading to a certified record power conversion efficiency of 15.46%with Voc of 1.13 V and Jsc of 22.92 mA cm^(-2)for this type of modules.Importantly,all of the functional layers of the module are printed through a simple and high-speed(300 cm min^(-1))blade coating strategy in ambient atmosphere.These results mark a significant step toward the commercialization of all-printable carbon-based perovskite solar modules.
基金the China National Postdoctoral Program for Innovative Talents(Bx20200386)China Postdoctoral Science Foundation(2021M703586)+1 种基金Key Program of National Natural Science Foundation of China(52130401)National Natural Science Foundation of China(52204064,52104055)for financial support.
文摘Nanocellulose,a natural polymeric nanomaterial,has attracted significant attention in enhanced oil recovery(EOR)applications due to its abundance,nanoscale,high oil-water interfacial adsorption ef-ficiency.In this study,surface-functionalized cellulose nanocrystals(SF-CNCs)were prepared via hy-drochloric acid hydrolysis and chemical modification,with adaptable nanosize and considerable dispersion stability in low-permeability reservoirs.The SF-CNCs were structurally characterized by FT-IR,Cryo-TEM,which have a diameter of 5-10 nm and a length of 100-200 nm.The SF-CNC dispersions possessed higher stability and stronger salt-tolerance than those of corresponding CNC dispersions,due to the strong hydrophilicity of the sulfonic acid group.It was synergistically used with a non-ionic surfactant(APG1214)to formulate a combined flooding system(0.1 wt%SF-CNC+0.2 wt%APG1214).The combined flooding system exhibits strong emulsification stability,low oil-water interfacial tension of o.03 mN/m,and the ability to alter the wettability for oil-wetting rocks.Furthermore,the combined system was_able to provide an optimum EOR efficiency of 20.2%in low-permeability cores with 30.13×10^(-3)μm^(2).Notably.it can enlarge the sweep volume and increase the displacement efficiency simultaneously.Overall,the newly formulated nanocellulose/surfactant combined system exhibits a remarkable EoR performance in low-permeability reservoirs.
基金Research Foundation from National Innovation Center of Advanced Dyeing&Finishing Technology,China(No.2022GCJJ10)。
文摘Nitrite is a commonly used additive in cured foods and its sensitive detection is important to human health.In this work,a simple but sensitive electrochemical sensor for nitrite was developed.Conductive carbon black(VXC-72R)functionalized with a cationic surfactant cetyltrimethylammonium bromide(CTAB)was used as an electrode material,and was coated on a glassy carbon electrode(GCE)to fabricate the electrochemical sensor(CTAB/VXC-72R/GCE)for nitrite.Zeta potential characterization and a series of electrochemical tests were carried out on several materials.It was found that the present sensor showed an enhanced sensitivity towards nitrite detection due to the enhanced surface positive charge revealed by the Zeta potential.Under optimal conditions,the ranges of good linear relationship between the peak current and the nitrite concentration were obtained to be 0.5-5.0μmol/L and 5.0-1087.0μmol/L with a lower detection limit of 0.30μmol/L.It was also successfully used for the determination of nitrite in cured food samples with excellent reproducibility,stability and selectivity.
文摘The objective of this study is to analyze the effects of using surfactant(CTAB)and cellulose nanofibers(NFC)as an admixture in cement mortars.We examined composite properties as porosity,compression energy,thermal conductivity and hydration.The results showed that with the addition of 0.7%by weight of NFC per emulsion in the presence of a cationic surfactant(CTAB).The new material produced presented a dry porosity between 4.7%and 4.4%,compressive strength between 9.8 and 22.9 MPa,and thermal conductivity between 0.95 and 2.25 W·m^(−1)·K^(−1).Thus we show better mechanical and thermal performance than that traditional Portland cement mortar with a density similar.In addition,the mortar made by emulsion of ordinary portland cement,cellulose nanofiber and organophilic clay(OC)treated with cetyltrimethylammonium bromide(CTAB)obtained has good resistance under high temperature and water,as well as excellent thermal insulation performance under high temperature and humidity conditions.This study verified that the presence of NFC promotes hydration,leading to the production of more calcium silicate and portlandite gel.
基金This study was supported by the Fundamental Research Funds for Zhejiang Provincial Universities and Research Institutes(No.2021J004)the Scientific Research Fund of Zhejiang Provincial Education Department(No.Y202044721).
文摘In this study,a novel absorpent(MSAR600℃)with a hydrophobic surface and hierarchical porous structure for the removal of kitchen oil was facilely fabricated from the macroalgae,laver(Porphyra haitanensis)by incorpor-ating high-temperature carbonization and alkyl polyglucosides(APG)and rhamnolipid(RL)surfactants modifi-cation.The characterization results showed MSAR600℃ possessed a louts-leaf-like papillae microstructure with high contact angle(137.5°),abundant porous structure with high specific surface area(23.4 m^(2)/g),and various oxygen-containing functional groups(-OH,C=O,C-O).Batch adsorption experiments were conducted to inves-tigate the effect of adsorption time,temperature,pH,and absorbent dose on kitchen oil adsorption performance.Then the practical application for the removal of kitchen oil using MSAR600℃ was also performed.The results showed that MSAR600℃ had a higher removal efficiency for kitchen oil(75.98%),compared with the commercial detergent(72.3%).This study demonstrates an example of fabricating a green tableware detergent for enhanced removal performance of kitchen oil.
文摘Combining low salinity water (LSW) with surfactants has an enormous potential for enhancing oil recovery processes. However, there is no consensus about the mechanisms involved, in addition to the fact that several studies have been conducted in model systems, while experiments with rocks and reservoir fluids are scarce. This study presents a core-flooding experiment of LSW injection, with and without surfactant, using the core and heavy oil samples obtained from a sandstone reservoir in southeastern Mexico. The effluents and the crude oil obtained at each stage were analyzed. The study was complemented by tomographic analysis. The results revealed that LSW injection and hybrid process with surfactants obtained an increase of 11.4 percentage points in recovery factor. Various phenomena were caused by LSW flooding, such as changes in wettability and pH, ion exchange, mineral dissolution, detachment of fines and modification of the hydrocarbon profile. In the surfactant flooding, the reduction of interfacial tension and alteration of wettability were the main mechanisms involved. The findings of this work also showed that the conditions believed to be necessary for enhanced oil recovery with LSW, such as the presence of kaolinite or high acid number oil, are not relevant.
