An experimental investigation into the thermal conductivity of CF-SiC two-phase composite asphalt concrete is presented.The main objective of this study was to verify the possibility of using SiC powder instead of min...An experimental investigation into the thermal conductivity of CF-SiC two-phase composite asphalt concrete is presented.The main objective of this study was to verify the possibility of using SiC powder instead of mineral powder as the thermal conductive filler to prepare a new type of asphalt concrete and improve the efficiency of electrothermal snow and ice melting systems accordingly.The thermal conductivity of asphalt concrete prepared with different thermally conductive fillers was tested by a transient plane source method,and the related performances were measured.Then the temperature rise rate and surface temperature were studied through field heating tests.Finally,the actual ice melting efficiency of the thermally conductive asphalt concrete was evaluated using an effective electrothermal system.As shown by the experimental results,the composite made of SiC powder and carbon fiber has a high thermal conductivity.When SiC replaces mineral powder,the thermal conductivity of the asphalt mixture increases first and then decreases with the increase of carbon fiber content.In the present study,in particular,the thermal conductivity attained a peak when the carbon fiber content was 0.2%of the aggregate mass.展开更多
In general,acid aggregates are not used in combination with asphalt concrete because of their poor compatibility with the asphalt binder,which typically results in a scarce water stability of the concrete.In the prese...In general,acid aggregates are not used in combination with asphalt concrete because of their poor compatibility with the asphalt binder,which typically results in a scarce water stability of the concrete.In the present study,the feasibility of a new approach based on the combination of acid granite fine aggregate with alkaline limestone coarse aggregate and Portland cement filler has been assessed.The mineral and chemical compositions of these three materials have first been analyzed and compared.Then,the effect of different amounts of Portland cement(0%,25%,50%,75%and 100%of the total filler by weight)on the mechanical performance and water stability of the asphalt concrete has been considered.Asphalt concrete has been designed by using the Marshall method,and the mechanical performance indexes of this material,including the Marshall stability and indirect tensile strength(ITS),have been measured together with the related water stability indexes(namely the Marshall stability(RMS)and tensile strength ratio(TSR)).The results indicate that the alkaline limestone coarse aggregate and Portland cement filler can balance the drawback caused by the acid granite fine aggregate.The asphalt concrete has good mechanical performances and water stability when the amount of common limestone powder filler replaced by cement is not less than 75%.展开更多
The variations in the viscoelastic characteristics of asphalt concrete due to testing mode are assessed and modeled in the present investigation.Asphalt concrete mixture was prepared at its optimum asphalt binder requ...The variations in the viscoelastic characteristics of asphalt concrete due to testing mode are assessed and modeled in the present investigation.Asphalt concrete mixture was prepared at its optimum asphalt binder requirement and compacted in slab mold with the aid of roller compaction.Beam specimens of 6.2 cm width,5.6 cm depth,and 40 cm length,were obtained from the slab samples with the aid of a diamond saw,and tested using controlled stress and strain techniques under dynamic flexural stresses.The viscoelastic properties such as the phase angle,cumulative dissipated energy,permanent deformation,flexural stiffness,and micro strain were monitored and modeled among the two testing techniques.It was noticed that higher micro strain and permanent deformation are detected when testing the asphalt concrete specimens under constant strain mode.However,higher phase angle,flexural stiffness,and energy dissipation could be observed under the constant stress mode of the test.展开更多
In order to investigate the fatigue behavior of asphalt concrete, a new numerical approach based on a bi-linear cohesive zone model （CZM） is developed. Integrated with the CZM, a fatigue damage evolution model is es...In order to investigate the fatigue behavior of asphalt concrete, a new numerical approach based on a bi-linear cohesive zone model （CZM） is developed. Integrated with the CZM, a fatigue damage evolution model is established to indicate the gradual degradation of cohesive properties of asphalt concrete under cyclic loading. Then the model is implemented in the finite element software ABAQUS through a user-defined subroutine. Based on the proposed model, an indirect tensile fatigue test is finally simulated. The fatigue lives obtained through numerical analysis show good agreement with laboratory results. Fatigue damage accumulates in a nonlinear manner during the cyclic loading process and damage initiation phase is the major part of fatigue failure. As the stress ratio increases, the time of the steady damage growth stage decreases significantly. It is found that the proposed fatigue damage evolution model can serve as an accurate and efficient tool for the prediction of fatigue damage of asphalt concrete.展开更多
According to the winter temperature of Peking,the freeze-thaw（FT） condition in laboratory was determined.Seven groups of epoxy asphalt concrete（EAC） specimen were exposed to different FT cycles.The flexural modulu...According to the winter temperature of Peking,the freeze-thaw（FT） condition in laboratory was determined.Seven groups of epoxy asphalt concrete（EAC） specimen were exposed to different FT cycles.The flexural modulus and fracture energy（G_F） of EAC exposed to different FT cycles were obtained through the 3-point bending test.Meanwhile,the plane strain fracture toughness（K_（IC）） of EAC was obtained through numerical simulation.The results show that the flexural modulus of the FT conditioned EAC samples decreases with the increase of FT cycles.The FT damage of flexural modulus is 60%after 30 FT cycles.Nevertheless,with the increase of FT cycles,the G_F and K_（IC） of EAC decrease first and then increase after 15 FT cycles.展开更多
The research considered urgent ecological reasons linked to environment such as worn tires, the waste tire rubber＇s powder was collected from the tire cars repair shops （passed from the sieve No 18 μm）, and used t...The research considered urgent ecological reasons linked to environment such as worn tires, the waste tire rubber＇s powder was collected from the tire cars repair shops （passed from the sieve No 18 μm）, and used to improve the asphalt concrete properties. Raw materials used were prepared and tested. Varies of asphalt concrete mixtures were prepared with different ratios of bitumen （5, 5.5, 6, 6.5, 7% % of concrete weight）. The Marshall mix design method was used to determine optimum conditions for bitumen in asphalt concrete with specific weight, stability and flow Test, the optimum amount of bitumen was 6.1% of whole asphalt concrete. The different percentages of waste tire rubber powder （0.0, 0.05, 0.10, 0.15% of bitumen weight） were added in optimum bitumen of asphalt concretes, then specific weight and Marshall test were evaluated. These asphalt-rubber mixtures were found to act quite differently from traditional, unmodified asphalt mixtures. However, these results indicate that improved pavement performance can be achieved with asphalt-rubber binder.展开更多
We established a user-defined micromechanical model using discrete element method （DEM） to investigate the cracking behavior of asphalt concrete （AC）. Using the ＂Fish＂ language provided in the particle flow code...We established a user-defined micromechanical model using discrete element method （DEM） to investigate the cracking behavior of asphalt concrete （AC）. Using the ＂Fish＂ language provided in the particle flow code in 3-Demensions （PFC3D）, the air voids and mastics in asphalt concrete were realistically built as two distinct phases. With the irregular shape of individual aggregate particles modeled using a clump of spheres of different sizes, the three-dimensional （3D） discrete element model was able to account for aggregate gradation and fraction. Laboratory uniaxial complex modulus test and indirect tensile strength test were performed to obtain input material parameters for the numerical simulation. A set of the indirect tensile test were simulated to study the cracking behavior of AC at two levels of temperature, i e, -10 ℃ and 15 ℃. The predicted results of the numerical simulation were compared with laboratory experimental measurements. Results show that the 3D DEM model is able to predict accurately the fracture pattern of different asphalt mixtures. Based on the DEM model, the effects of air void content and aggregate volumetric fraction on the cracking behavior of asphalt concrete were evaluated.展开更多
The self-monitoring application of asphalt concrete containing graphite and carbon fibers using indirect tensile test and wheel rolling test were introduced. The experiment results indicate that this kind of pitch-bas...The self-monitoring application of asphalt concrete containing graphite and carbon fibers using indirect tensile test and wheel rolling test were introduced. The experiment results indicate that this kind of pitch-based composite is effective for strain/stress self-monitoring. In the indirect tensile test, for a completely conductive asphalt concrete specimen, the piezoresistivity was very weak and slightly positive, which meant the resistivity increase with the increment of tensile strain at all stress/strain amplitudes, with the gage factor as high as 6. The strain self-sensing ability was superior in the case of higher graphite content. However, when the conductive concrete was embedded into common asphalt concrete specimen as a partial structure function, the piezoresistivity was positive at all stress/strain amplitudes and with the gage factor of 13, which was much higher than that of completely conductive specimen. Thus, the strain self-sensing ability was superior when conductive asphalt concrete was taken in as a partial structure function. In the wheel-rolling test, the piezoresistivity was highly positive. At any stress amplitude, the piezoresistivity was strong, with the gage factor as high as 100, which was higher for a stress amplitude of 0.7 MPa than that of 0.5 MPa.展开更多
A user-defined three-dimensional （3D） discrete element model was presented to predict the dynamic modulus and phase angle of asphalt concrete （AC）. The 3D discrete element method （DEM） model of AC was constructe...A user-defined three-dimensional （3D） discrete element model was presented to predict the dynamic modulus and phase angle of asphalt concrete （AC）. The 3D discrete element method （DEM） model of AC was constructed employing a user-defined computer program developed using the ＂Fish＂ language in PFC3D. Important microstructural features of AC were modeled, including aggregate gradation, air voids and mastic. The irregular shape of aggregate particle was modeled using a clump of spheres. The developed model was validated through comparing with experimental measurements and then used to simulate the cyclic uniaxial compression test, based on which the dynamic modulus and phase angle were calculated from the output stress- strain relationship. The effects of air void content, aggregate stiffness and volumetric fraction on AC modulus were further investigated. The experimental results show that the 3D DEM model is able to accurately predict both dynamic modulus and phase angle of AC across a range of temperature and loading frequencies. The user- defined 3D model also demonstrated significant improvement over the general existing two-dimensional models.展开更多
A user-defined micromechanical model was developed to investigate the fracture mechanism of asphalt concrete （AC） using the discrete element method （DEM）. A three-dimensional （3D） AC beam was built using the ＂F...A user-defined micromechanical model was developed to investigate the fracture mechanism of asphalt concrete （AC） using the discrete element method （DEM）. A three-dimensional （3D） AC beam was built using the ＂Fish＂ language provided by PFC3D and was employed to simulate the three-point bending beam test at two temperature levels： -10 ℃ and 15℃. The AC beam was modeled with the consideration of the microstructural features of asphalt mixtures. Uniaxial complex modulus test and indirect tensile strength test were conducted to obtain material input parameters for numerical modeling. The 3D predictions were validated using laboratory experimental measurements of AC beams prepared by the same mixture design. Effects of mastic stiffness, cohesive and adhesive strength on AC fracture behavior were investigated using the DEM model. The results show that the 3D DEM fracture model can accurately predict the fracture patterns of asphalt concrete. The ratio of stress at interfaces to the stress in mastics increases as the mastic stiffness decreases; however, the increase in the cohesive strength or adhesive strength shows no significant influence on the tensile strength.展开更多
The objective of this work is to develop a novel methodology for determining real resistivity of conductive asphalt concrete based on two-electrode method.Due to an influence of contact resistance,the measured resisti...The objective of this work is to develop a novel methodology for determining real resistivity of conductive asphalt concrete based on two-electrode method.Due to an influence of contact resistance,the measured resistivity is always not equal to the real resistivity.To determine the real resistivity,a linear relationship of the measured resistivity,contact resistance and the real resistivity was established.Then experiments for six specimens with varying graphite contents were designed and performed to validate the formulation.Results of experiments demonstrate that the slope of the line represents contact resistance,and the intercept indicates the real resistivity.The effects of graphite content on contact resistance and real resistivity are also revealed.Finally,results show that the influence of contact resistance on accuracy of resisitvity measurement becomes more serious if graphite content is beyond 3%.Hence,it is the time to choose this novel methodology to determine the real resistivity of asphalt concrete by taking account of contact resistance.展开更多
A viscoelastic micromechanical model is presented to predict the dynamic modulus of asphalt concrete （AC） and investigate the effect of imperfect interface between asphalt mastic and aggregates on the overall viscoe...A viscoelastic micromechanical model is presented to predict the dynamic modulus of asphalt concrete （AC） and investigate the effect of imperfect interface between asphalt mastic and aggregates on the overall viscoelastic characteristics of AC. The linear spring layer model is introduced to simulate the interface imperfection. Based on the effective medium theory, the viscoelastic micromechanical model is developed by two equivalence processes. The present prediction is compared with available experimental data to verify the developed framework. It is found that the proposed model has the capability to predict the dynamic modulus of AC. Interface effect on the dynamic modulus of AC is discussed using the developed model. It is shown that the interfacial bonding strength has a significant influence on the global mechanical performance of AC, and that continued improvement in surface fimctionalization is necessary to realize the full potential of aggregates reinforcement.展开更多
In this paper, a four-layered road structure containing a top-down crack is investigated by performing finite element analyses in ABAQUS. In this study, in addition to the vertical load of a vehicle wheel, the horizon...In this paper, a four-layered road structure containing a top-down crack is investigated by performing finite element analyses in ABAQUS. In this study, in addition to the vertical load of a vehicle wheel, the horizontal load as well as its position with respect to the crack is also considered in the analyses, and the crack tip parameters including stress intensity factors(SIFs) and T-stress are then calculated. Moreover, influence of elastic modulus and thickness of the pavement layers on the crack tip parameters is studied. Results show that the horizontal and vertical loads along with their position with respect to the crack, elastic modulus and thickness of the road layers influence the crack tip parameters(KⅠ, KⅡ and T-stress) significantly. It was also found that for the cases that the vehicle wheel is positioned near the crack plane, only the shear deformation mode is observed at the crack tip;while, for the vehicle wheel positions far from the crack, only the opening mode is observed, and between these positions, both the opening and shear deformation modes(i.e., mixed mode Ⅰ/Ⅱ) are observed at the crack tip.展开更多
The addition of graphite powder in conventional asphalt mixture can produced asp halt concrete with excellent electrical performance. Percolation theor y was employed to discuss the relation between the conductivity a...The addition of graphite powder in conventional asphalt mixture can produced asp halt concrete with excellent electrical performance. Percolation theor y was employed to discuss the relation between the conductivity and graphite con tent of graphite-modified asphalt concrete. It was found that the results of pe rcolation model are consistent with experimental values. The percolation thresho ld of graphite-modified asphalt concrete is 10.94% graphite content account for the total volume of the binder phase consisting of asphalt and graphite. The cr itical exponent is 3.16, beyond the range of 1.6-2.1 for the standard lattice c ontinuous percolation problem. Its reason is that the tunnel conduction mec hanism originates near the critical percent content, which causes this system to be not universal. Tunnel mechanism is demonstrated by the nonlinear voltage-cu rrent characteristic near percolation threshold.The percolation model is able to well predict the formation and development of conductive network in graphite- modified asphalt concrete.展开更多
Materials such as Koch AH-70,basalt aggregate,limestone powder and graphite particles were used to prepare conductive asphalt concrete,which is a new type of multifunctional concrete.The mix proportion by weight was s...Materials such as Koch AH-70,basalt aggregate,limestone powder and graphite particles were used to prepare conductive asphalt concrete,which is a new type of multifunctional concrete.The mix proportion by weight was shown as follows.Fine aggregates (2.36-4.75 mm)∶fine aggregates (<2.36mm)∶limestone powder∶asphalt=120∶240∶14∶30.The content of added graphite particles ranged from 0% to 20%(by the weight of asphalt concrete).A conductive asphalt concrete with a resistivity around 10-10 3Ω·m was obtained.Special attention was paid to the effects of graphite content,graphite physical-chemical properties,asphalt content and temperature on the resistivity.Furthermore,an attempt was made to develop an electrically conductive model for asphalt concrete.展开更多
This paper presents an investigation into modelling the rheological properties of epoxy asphalt concrete( EAC) by using the Huet-Sayegh model. Complex modulus tests were conducted on EAC specimens at various temperatu...This paper presents an investigation into modelling the rheological properties of epoxy asphalt concrete( EAC) by using the Huet-Sayegh model. Complex modulus tests were conducted on EAC specimens at various temperature and loading frequency conditions. Dynamic modulus and phase angles obtained from the complex modulus tests were used in the construction of the Huet-Sayegh model. The dynamic modulus master curve was developed by the Huet-Sayegh model as well as the Burgers model for comparison purpose. The results showed that EAC exhibits typical rheological behavior whose dynamic modulus decreases with the increase of temperature while increases with the increase of frequency,and phase angles increase with the decrease of frequencies and the increase of temperatures. The Huet-Sayegh model predicts the dynamic modulus master curve of EAC very well and much better than the Burgers model over a wide range of frequencies.展开更多
The main objective of this paper is to evaluate the effects of asphalt concrete types on the microstructural characteristics at high-temperature. Suspend-dense structure and Skeleton-dense structure were selected to i...The main objective of this paper is to evaluate the effects of asphalt concrete types on the microstructural characteristics at high-temperature. Suspend-dense structure and Skeleton-dense structure were selected to investigate the deformation of pavement at meso-scale. The internal microstructures of typical asphalt concretes, AC, SUP and SMA, were scanned by X-ray CT device, and microstructural changes before and after high-temperature damage were researched by digital image processing. Adaptive threshold segmentation algorithm（ATSA） based on image radius was developed and utilized to obtain the binary images of aggregates, air-voids and asphalt mastic. Then the shape and distribution of air-voids and aggregates were analyzed. The results show that the ATSA can distinguish the target and background effectively. Gradation and coarse aggregate size of asphalt mixtures have an obvious influence on the distribution of air-voids. The movements of aggregate particles are complex and aggregates with elliptic sharp show great rotation. The effect of gradation on microstructure during high-temperature damage promotes the research about the failure mechanism of asphalt concrete pavement.展开更多
The changes of resistivity of conductive asphalt concrete at different temperatures were studied,and positive temperature coefficient（PTC）modelwas established to estimate the influence of temperature on the resistiv...The changes of resistivity of conductive asphalt concrete at different temperatures were studied,and positive temperature coefficient（PTC）modelwas established to estimate the influence of temperature on the resistivity quantitatively,which eliminated the interference with conductivity evaluation brought by temperature variation.Finally,the analysis of temperature cycling test results proves that the changes of percolation network structure caused by temperature variation prompt the emergence of PTC of conductive asphalt concrete.展开更多
The fatigue-life of asphalt concrete is often related to environmental condition,loading condition,ageing,material composition and properties.This work investigates the influence of short and long term ageing of labor...The fatigue-life of asphalt concrete is often related to environmental condition,loading condition,ageing,material composition and properties.This work investigates the influence of short and long term ageing of laboratory beam specimens,asphalt percent,and testing temperature on fatigue life of asphalt concrete wearing course.Slab samples of(30 × 40 × 6)cm have been prepared,beam specimens of(40 × 5 × 6)cm were extracted from the asphalt concrete slab samples and tested for fatigue-life under the impact of three levels of micro strain(250,400,and[3]750)at(5,20,and 30)℃ before and after practicing long-term aging.It was observed that the fatigue-life decreased by(85 and 97)%,(87.5 and 97.4)%,(71.4 and 95.2)%after increasing the applied microstrain from(250 to 400 and 750)μƐfor control mixture and for mixtures subjected to shortand long-term ageing processes respectively.The fatigue-life increased by(142.8 and 257.1)%,(34.4 and 57.8)%and(10 and 30)%when the asphalt content increased from(4.4 to 4.9 and 5.4)%for specimens practicing the applied microstrain of(250,400 and 750)μƐrespectively.It can be concluded that the fatigue life increases by a range of(two to fifteen)folds when the testing temperature increases from(5 to 20 and 30)℃ respectively.展开更多
Various modes of compacting the asphalt concrete mixture can create mechanically different behaviour of the prepared specimens and can alter its sustainability.An attempt has been made in the present assessment to pre...Various modes of compacting the asphalt concrete mixture can create mechanically different behaviour of the prepared specimens and can alter its sustainability.An attempt has been made in the present assessment to prepare asphalt concrete specimens by implementation of three modes of compaction,the gyratory,the roller,and the Marshall hammer.The specimens were prepared at the target bulk density of Marshall method at optimum asphalt content.Extra specimens were prepared at 0.5%asphalt below and above the optimum.Core specimens have been obtained from the roller compacted slab samples.The specimens were tested for the Marshall stiffness,tensile,and shear strength.It was observed that at optimum asphalt content,the indirect tensile strength declines by(18.8 and 70.5)%for gyratory and roller compacted specimens respectively as compared with hammer compacted specimens.At optimum asphalt content,the shear strength declines by(70.5 and 82.2)%while Marshall stiffness declines by(10.2 and 44.8)%for hammer and roller compacted specimens as compared with that of gyratory compacted specimen.Specimens prepared by gyratory compaction are less susceptible to the change in the testing temperature as compared with other modes of compaction.It is recommended to consider the mode of compaction to suit the required design property of sustainable asphalt concrete mixture.展开更多
基金the support of the Joint Funds of the Natural Science Foundation of Hubei Province(2022CFD130)the Technology Innovation Project of Hubei Province(Key Program,No.2023BEB010)+1 种基金the Key Research and Development Program of Hubei Province(No.2021BGD015)the Knowledge Innovation Project of Wuhan(No.2022010801010259).
文摘An experimental investigation into the thermal conductivity of CF-SiC two-phase composite asphalt concrete is presented.The main objective of this study was to verify the possibility of using SiC powder instead of mineral powder as the thermal conductive filler to prepare a new type of asphalt concrete and improve the efficiency of electrothermal snow and ice melting systems accordingly.The thermal conductivity of asphalt concrete prepared with different thermally conductive fillers was tested by a transient plane source method,and the related performances were measured.Then the temperature rise rate and surface temperature were studied through field heating tests.Finally,the actual ice melting efficiency of the thermally conductive asphalt concrete was evaluated using an effective electrothermal system.As shown by the experimental results,the composite made of SiC powder and carbon fiber has a high thermal conductivity.When SiC replaces mineral powder,the thermal conductivity of the asphalt mixture increases first and then decreases with the increase of carbon fiber content.In the present study,in particular,the thermal conductivity attained a peak when the carbon fiber content was 0.2%of the aggregate mass.
基金supported by the Science and Technology Planning Project of Zhejiang Provincial Department of Transportation(2021012)Zhejiang Provincial Natural Science Foundation of China under Grant(No.LGG21E080002).
文摘In general,acid aggregates are not used in combination with asphalt concrete because of their poor compatibility with the asphalt binder,which typically results in a scarce water stability of the concrete.In the present study,the feasibility of a new approach based on the combination of acid granite fine aggregate with alkaline limestone coarse aggregate and Portland cement filler has been assessed.The mineral and chemical compositions of these three materials have first been analyzed and compared.Then,the effect of different amounts of Portland cement(0%,25%,50%,75%and 100%of the total filler by weight)on the mechanical performance and water stability of the asphalt concrete has been considered.Asphalt concrete has been designed by using the Marshall method,and the mechanical performance indexes of this material,including the Marshall stability and indirect tensile strength(ITS),have been measured together with the related water stability indexes(namely the Marshall stability(RMS)and tensile strength ratio(TSR)).The results indicate that the alkaline limestone coarse aggregate and Portland cement filler can balance the drawback caused by the acid granite fine aggregate.The asphalt concrete has good mechanical performances and water stability when the amount of common limestone powder filler replaced by cement is not less than 75%.
文摘The variations in the viscoelastic characteristics of asphalt concrete due to testing mode are assessed and modeled in the present investigation.Asphalt concrete mixture was prepared at its optimum asphalt binder requirement and compacted in slab mold with the aid of roller compaction.Beam specimens of 6.2 cm width,5.6 cm depth,and 40 cm length,were obtained from the slab samples with the aid of a diamond saw,and tested using controlled stress and strain techniques under dynamic flexural stresses.The viscoelastic properties such as the phase angle,cumulative dissipated energy,permanent deformation,flexural stiffness,and micro strain were monitored and modeled among the two testing techniques.It was noticed that higher micro strain and permanent deformation are detected when testing the asphalt concrete specimens under constant strain mode.However,higher phase angle,flexural stiffness,and energy dissipation could be observed under the constant stress mode of the test.
基金The Open Research Fund of Key Laboratory of Highway Engineering of Sichuan Province of Southw est Jiaotong University (No.LHTE002201102)
文摘In order to investigate the fatigue behavior of asphalt concrete, a new numerical approach based on a bi-linear cohesive zone model （CZM） is developed. Integrated with the CZM, a fatigue damage evolution model is established to indicate the gradual degradation of cohesive properties of asphalt concrete under cyclic loading. Then the model is implemented in the finite element software ABAQUS through a user-defined subroutine. Based on the proposed model, an indirect tensile fatigue test is finally simulated. The fatigue lives obtained through numerical analysis show good agreement with laboratory results. Fatigue damage accumulates in a nonlinear manner during the cyclic loading process and damage initiation phase is the major part of fatigue failure. As the stress ratio increases, the time of the steady damage growth stage decreases significantly. It is found that the proposed fatigue damage evolution model can serve as an accurate and efficient tool for the prediction of fatigue damage of asphalt concrete.
基金The National Natural Science Foundation of China(No.51378122)
文摘According to the winter temperature of Peking,the freeze-thaw（FT） condition in laboratory was determined.Seven groups of epoxy asphalt concrete（EAC） specimen were exposed to different FT cycles.The flexural modulus and fracture energy（G_F） of EAC exposed to different FT cycles were obtained through the 3-point bending test.Meanwhile,the plane strain fracture toughness（K_（IC）） of EAC was obtained through numerical simulation.The results show that the flexural modulus of the FT conditioned EAC samples decreases with the increase of FT cycles.The FT damage of flexural modulus is 60%after 30 FT cycles.Nevertheless,with the increase of FT cycles,the G_F and K_（IC） of EAC decrease first and then increase after 15 FT cycles.
文摘The research considered urgent ecological reasons linked to environment such as worn tires, the waste tire rubber＇s powder was collected from the tire cars repair shops （passed from the sieve No 18 μm）, and used to improve the asphalt concrete properties. Raw materials used were prepared and tested. Varies of asphalt concrete mixtures were prepared with different ratios of bitumen （5, 5.5, 6, 6.5, 7% % of concrete weight）. The Marshall mix design method was used to determine optimum conditions for bitumen in asphalt concrete with specific weight, stability and flow Test, the optimum amount of bitumen was 6.1% of whole asphalt concrete. The different percentages of waste tire rubber powder （0.0, 0.05, 0.10, 0.15% of bitumen weight） were added in optimum bitumen of asphalt concretes, then specific weight and Marshall test were evaluated. These asphalt-rubber mixtures were found to act quite differently from traditional, unmodified asphalt mixtures. However, these results indicate that improved pavement performance can be achieved with asphalt-rubber binder.
基金Funded by the National High-tech Research and Development of China (‘863' Program) (No. 2006AA11Z110)
文摘We established a user-defined micromechanical model using discrete element method （DEM） to investigate the cracking behavior of asphalt concrete （AC）. Using the ＂Fish＂ language provided in the particle flow code in 3-Demensions （PFC3D）, the air voids and mastics in asphalt concrete were realistically built as two distinct phases. With the irregular shape of individual aggregate particles modeled using a clump of spheres of different sizes, the three-dimensional （3D） discrete element model was able to account for aggregate gradation and fraction. Laboratory uniaxial complex modulus test and indirect tensile strength test were performed to obtain input material parameters for the numerical simulation. A set of the indirect tensile test were simulated to study the cracking behavior of AC at two levels of temperature, i e, -10 ℃ and 15 ℃. The predicted results of the numerical simulation were compared with laboratory experimental measurements. Results show that the 3D DEM model is able to predict accurately the fracture pattern of different asphalt mixtures. Based on the DEM model, the effects of air void content and aggregate volumetric fraction on the cracking behavior of asphalt concrete were evaluated.
基金the Outstanding Youth Foundation of Hubei Province(No.2004ABB019)Program for New Century Excellent Talents in University,China(No.NCET-05-0665)
文摘The self-monitoring application of asphalt concrete containing graphite and carbon fibers using indirect tensile test and wheel rolling test were introduced. The experiment results indicate that this kind of pitch-based composite is effective for strain/stress self-monitoring. In the indirect tensile test, for a completely conductive asphalt concrete specimen, the piezoresistivity was very weak and slightly positive, which meant the resistivity increase with the increment of tensile strain at all stress/strain amplitudes, with the gage factor as high as 6. The strain self-sensing ability was superior in the case of higher graphite content. However, when the conductive concrete was embedded into common asphalt concrete specimen as a partial structure function, the piezoresistivity was positive at all stress/strain amplitudes and with the gage factor of 13, which was much higher than that of completely conductive specimen. Thus, the strain self-sensing ability was superior when conductive asphalt concrete was taken in as a partial structure function. In the wheel-rolling test, the piezoresistivity was highly positive. At any stress amplitude, the piezoresistivity was strong, with the gage factor as high as 100, which was higher for a stress amplitude of 0.7 MPa than that of 0.5 MPa.
基金Funded by the National "863" Plan Foundation of China(No.2006AA11Z110)
文摘A user-defined three-dimensional （3D） discrete element model was presented to predict the dynamic modulus and phase angle of asphalt concrete （AC）. The 3D discrete element method （DEM） model of AC was constructed employing a user-defined computer program developed using the ＂Fish＂ language in PFC3D. Important microstructural features of AC were modeled, including aggregate gradation, air voids and mastic. The irregular shape of aggregate particle was modeled using a clump of spheres. The developed model was validated through comparing with experimental measurements and then used to simulate the cyclic uniaxial compression test, based on which the dynamic modulus and phase angle were calculated from the output stress- strain relationship. The effects of air void content, aggregate stiffness and volumetric fraction on AC modulus were further investigated. The experimental results show that the 3D DEM model is able to accurately predict both dynamic modulus and phase angle of AC across a range of temperature and loading frequencies. The user- defined 3D model also demonstrated significant improvement over the general existing two-dimensional models.
基金Project(51208178)supported by the National Natural Science Foundation of ChinaProject(2012M520991)supported by China Postdoctoral Science Foundation
文摘A user-defined micromechanical model was developed to investigate the fracture mechanism of asphalt concrete （AC） using the discrete element method （DEM）. A three-dimensional （3D） AC beam was built using the ＂Fish＂ language provided by PFC3D and was employed to simulate the three-point bending beam test at two temperature levels： -10 ℃ and 15℃. The AC beam was modeled with the consideration of the microstructural features of asphalt mixtures. Uniaxial complex modulus test and indirect tensile strength test were conducted to obtain material input parameters for numerical modeling. The 3D predictions were validated using laboratory experimental measurements of AC beams prepared by the same mixture design. Effects of mastic stiffness, cohesive and adhesive strength on AC fracture behavior were investigated using the DEM model. The results show that the 3D DEM fracture model can accurately predict the fracture patterns of asphalt concrete. The ratio of stress at interfaces to the stress in mastics increases as the mastic stiffness decreases; however, the increase in the cohesive strength or adhesive strength shows no significant influence on the tensile strength.
基金Project(51178348)supported by the National Natural Science Foundation of China
文摘The objective of this work is to develop a novel methodology for determining real resistivity of conductive asphalt concrete based on two-electrode method.Due to an influence of contact resistance,the measured resistivity is always not equal to the real resistivity.To determine the real resistivity,a linear relationship of the measured resistivity,contact resistance and the real resistivity was established.Then experiments for six specimens with varying graphite contents were designed and performed to validate the formulation.Results of experiments demonstrate that the slope of the line represents contact resistance,and the intercept indicates the real resistivity.The effects of graphite content on contact resistance and real resistivity are also revealed.Finally,results show that the influence of contact resistance on accuracy of resisitvity measurement becomes more serious if graphite content is beyond 3%.Hence,it is the time to choose this novel methodology to determine the real resistivity of asphalt concrete by taking account of contact resistance.
基金Project(51408173)supported by the National Natural Science Foundation of China
文摘A viscoelastic micromechanical model is presented to predict the dynamic modulus of asphalt concrete （AC） and investigate the effect of imperfect interface between asphalt mastic and aggregates on the overall viscoelastic characteristics of AC. The linear spring layer model is introduced to simulate the interface imperfection. Based on the effective medium theory, the viscoelastic micromechanical model is developed by two equivalence processes. The present prediction is compared with available experimental data to verify the developed framework. It is found that the proposed model has the capability to predict the dynamic modulus of AC. Interface effect on the dynamic modulus of AC is discussed using the developed model. It is shown that the interfacial bonding strength has a significant influence on the global mechanical performance of AC, and that continued improvement in surface fimctionalization is necessary to realize the full potential of aggregates reinforcement.
文摘In this paper, a four-layered road structure containing a top-down crack is investigated by performing finite element analyses in ABAQUS. In this study, in addition to the vertical load of a vehicle wheel, the horizontal load as well as its position with respect to the crack is also considered in the analyses, and the crack tip parameters including stress intensity factors(SIFs) and T-stress are then calculated. Moreover, influence of elastic modulus and thickness of the pavement layers on the crack tip parameters is studied. Results show that the horizontal and vertical loads along with their position with respect to the crack, elastic modulus and thickness of the road layers influence the crack tip parameters(KⅠ, KⅡ and T-stress) significantly. It was also found that for the cases that the vehicle wheel is positioned near the crack plane, only the shear deformation mode is observed at the crack tip;while, for the vehicle wheel positions far from the crack, only the opening mode is observed, and between these positions, both the opening and shear deformation modes(i.e., mixed mode Ⅰ/Ⅱ) are observed at the crack tip.
基金Funded by the Outstanding Youth Foundation of Hubei Province of China (No.2004ABB019)
文摘The addition of graphite powder in conventional asphalt mixture can produced asp halt concrete with excellent electrical performance. Percolation theor y was employed to discuss the relation between the conductivity and graphite con tent of graphite-modified asphalt concrete. It was found that the results of pe rcolation model are consistent with experimental values. The percolation thresho ld of graphite-modified asphalt concrete is 10.94% graphite content account for the total volume of the binder phase consisting of asphalt and graphite. The cr itical exponent is 3.16, beyond the range of 1.6-2.1 for the standard lattice c ontinuous percolation problem. Its reason is that the tunnel conduction mec hanism originates near the critical percent content, which causes this system to be not universal. Tunnel mechanism is demonstrated by the nonlinear voltage-cu rrent characteristic near percolation threshold.The percolation model is able to well predict the formation and development of conductive network in graphite- modified asphalt concrete.
文摘Materials such as Koch AH-70,basalt aggregate,limestone powder and graphite particles were used to prepare conductive asphalt concrete,which is a new type of multifunctional concrete.The mix proportion by weight was shown as follows.Fine aggregates (2.36-4.75 mm)∶fine aggregates (<2.36mm)∶limestone powder∶asphalt=120∶240∶14∶30.The content of added graphite particles ranged from 0% to 20%(by the weight of asphalt concrete).A conductive asphalt concrete with a resistivity around 10-10 3Ω·m was obtained.Special attention was paid to the effects of graphite content,graphite physical-chemical properties,asphalt content and temperature on the resistivity.Furthermore,an attempt was made to develop an electrically conductive model for asphalt concrete.
基金Sponsored by the Natgional Natural Science Foundation of China(Grant No.51208103)the China Postdoctoral Science Foundation(Grant No.2012M520976)the Basic Research Foundation of Southeast University
文摘This paper presents an investigation into modelling the rheological properties of epoxy asphalt concrete( EAC) by using the Huet-Sayegh model. Complex modulus tests were conducted on EAC specimens at various temperature and loading frequency conditions. Dynamic modulus and phase angles obtained from the complex modulus tests were used in the construction of the Huet-Sayegh model. The dynamic modulus master curve was developed by the Huet-Sayegh model as well as the Burgers model for comparison purpose. The results showed that EAC exhibits typical rheological behavior whose dynamic modulus decreases with the increase of temperature while increases with the increase of frequency,and phase angles increase with the decrease of frequencies and the increase of temperatures. The Huet-Sayegh model predicts the dynamic modulus master curve of EAC very well and much better than the Burgers model over a wide range of frequencies.
基金Funded by National Natural Science Foundation of China(No.51178114)the Fundamental Research Funds for the Central Universities(No.CXLX12_0117)the Scientific Research Foundation of Graduate School of Southeast University(No.YBJJ1318)
文摘The main objective of this paper is to evaluate the effects of asphalt concrete types on the microstructural characteristics at high-temperature. Suspend-dense structure and Skeleton-dense structure were selected to investigate the deformation of pavement at meso-scale. The internal microstructures of typical asphalt concretes, AC, SUP and SMA, were scanned by X-ray CT device, and microstructural changes before and after high-temperature damage were researched by digital image processing. Adaptive threshold segmentation algorithm（ATSA） based on image radius was developed and utilized to obtain the binary images of aggregates, air-voids and asphalt mastic. Then the shape and distribution of air-voids and aggregates were analyzed. The results show that the ATSA can distinguish the target and background effectively. Gradation and coarse aggregate size of asphalt mixtures have an obvious influence on the distribution of air-voids. The movements of aggregate particles are complex and aggregates with elliptic sharp show great rotation. The effect of gradation on microstructure during high-temperature damage promotes the research about the failure mechanism of asphalt concrete pavement.
基金Funded by the National Natural Science Foundation of China(No.51178348)
文摘The changes of resistivity of conductive asphalt concrete at different temperatures were studied,and positive temperature coefficient（PTC）modelwas established to estimate the influence of temperature on the resistivity quantitatively,which eliminated the interference with conductivity evaluation brought by temperature variation.Finally,the analysis of temperature cycling test results proves that the changes of percolation network structure caused by temperature variation prompt the emergence of PTC of conductive asphalt concrete.
文摘The fatigue-life of asphalt concrete is often related to environmental condition,loading condition,ageing,material composition and properties.This work investigates the influence of short and long term ageing of laboratory beam specimens,asphalt percent,and testing temperature on fatigue life of asphalt concrete wearing course.Slab samples of(30 × 40 × 6)cm have been prepared,beam specimens of(40 × 5 × 6)cm were extracted from the asphalt concrete slab samples and tested for fatigue-life under the impact of three levels of micro strain(250,400,and[3]750)at(5,20,and 30)℃ before and after practicing long-term aging.It was observed that the fatigue-life decreased by(85 and 97)%,(87.5 and 97.4)%,(71.4 and 95.2)%after increasing the applied microstrain from(250 to 400 and 750)μƐfor control mixture and for mixtures subjected to shortand long-term ageing processes respectively.The fatigue-life increased by(142.8 and 257.1)%,(34.4 and 57.8)%and(10 and 30)%when the asphalt content increased from(4.4 to 4.9 and 5.4)%for specimens practicing the applied microstrain of(250,400 and 750)μƐrespectively.It can be concluded that the fatigue life increases by a range of(two to fifteen)folds when the testing temperature increases from(5 to 20 and 30)℃ respectively.
文摘Various modes of compacting the asphalt concrete mixture can create mechanically different behaviour of the prepared specimens and can alter its sustainability.An attempt has been made in the present assessment to prepare asphalt concrete specimens by implementation of three modes of compaction,the gyratory,the roller,and the Marshall hammer.The specimens were prepared at the target bulk density of Marshall method at optimum asphalt content.Extra specimens were prepared at 0.5%asphalt below and above the optimum.Core specimens have been obtained from the roller compacted slab samples.The specimens were tested for the Marshall stiffness,tensile,and shear strength.It was observed that at optimum asphalt content,the indirect tensile strength declines by(18.8 and 70.5)%for gyratory and roller compacted specimens respectively as compared with hammer compacted specimens.At optimum asphalt content,the shear strength declines by(70.5 and 82.2)%while Marshall stiffness declines by(10.2 and 44.8)%for hammer and roller compacted specimens as compared with that of gyratory compacted specimen.Specimens prepared by gyratory compaction are less susceptible to the change in the testing temperature as compared with other modes of compaction.It is recommended to consider the mode of compaction to suit the required design property of sustainable asphalt concrete mixture.
