Micro-sized silicon anodes have shown much promise in large-scale industrial production of high-energy lithium batteries.However,large volume change(>300%)of silicon anodes causes severe particle pulverization and ...Micro-sized silicon anodes have shown much promise in large-scale industrial production of high-energy lithium batteries.However,large volume change(>300%)of silicon anodes causes severe particle pulverization and the formation of unstable solid electrolyte interphases during cycling,leading to rapid capacity decay and short cycle life of lithium-ion batteries.When addressing such issues,binder plays key roles in obtaining good structural integrity of silicon anodes.Herein,we report a biopolymer composite binder composed of rigid poly(acrylic acid)(PAA)and flexible silk fibroin(SF)tailored for micro-sized silicon anodes.The PAA/SF binder shows robust gradient binding energy via chemical interactions between carboxyl and amide groups,which can effectively accommodate large volume change of silicon.This PAA/SF binder also shows much stronger adhesion force and improved binding towards high-surface/defective carbon additives,resulting in better electrochemical stability and higher coulombic efficiency,than conventional PAA binder.As such,micro-sized silicon/carbon anodes fabricated with novel PAA/SF binder exhibit much better cyclability(up to 500 cycles at 0.5 C)and enhanced rate capability compared with conventional PAA-based anodes.This work provides new insights into the design of functional binders for high-capacity electrodes suffering from large volume change for the development of nextgeneration lithium batteries.展开更多
In typical metal foundry applications,sand casting is still the most used technology.The related binder plays a very important role as its performances can directly influence the quality of castings.Among many binders...In typical metal foundry applications,sand casting is still the most used technology.The related binder plays a very important role as its performances can directly influence the quality of castings.Among many binders,glues of animal origin have attracted much attention in recent years due to their reduced environmental impact.How-ever,they display some drawbacks such as the tendency to coagulate easily at room temperature and a relatively low strength.In this study,a novel gas-hardening casting binder was prepared using an animal glue and anhy-drous potassium carbonate as a hydrolyzing agent to avoid undesired agglomeration.Moreover,sodium pyropho-sphate and furfuryl alcohol were exploited as modifiers to obtain a binder with a high compressive strength.The best modification conditions,determined by means of an orthogonal design matrix approach,were 4 g of Na2CO3,sodium pyrophosphate,furfuryl alcohol and animal glue with a ratio of 4:12:100,at 85°C and with a duration of 115 min,respectively.The viscosity of the mixture obtained under these optimized conditions was 1250 mPa⋅s.The compressive strength of the binder,hardened by CO_(2) gas,was 4.00 MPa.Its gas evolution at 850°C was 15 ml⋅g-1,and its residual strength after 10 min calculation at 800°C was 0.01 MPa,which is high enough to meet the requirement of core-making in foundry.Moreover,after hydrolysis and further modification,animal glue and modifiers displayed a grafting reaction and an esterification reaction,respectively,which made the adhesive network denser and improved its thermal stability.展开更多
Thermal spraying of cermet coatings is widely used for protection of machining parts against wear and corrosion. These coatings consist of WC particles in metal binders such as Co, Cr and Ni. Three kinds of WC powders...Thermal spraying of cermet coatings is widely used for protection of machining parts against wear and corrosion. These coatings consist of WC particles in metal binders such as Co, Cr and Ni. Three kinds of WC powders with different metal binders (Co, NiCr and CoCr) were sprayed by low power plasma spray system on Al-Si-Cu alloy substrate. Fundamental aspects of sprayed cermet coatings, including (i) the effects of binder type on the coating structure, (ii) the hardness and (iii) the microstructure, were investigated. All cermet coatings have the same phase structure such as WC and W2 C. However, the intensities of these phases are different in each coating, mainly due to the difference in solidification rate in each case. Moreover, the hardness measurements are found to be different in each coating. The results show that, binder type has a significant effect on the physical and mechanical properties of the sprayed coatings.展开更多
The use of the four new synthesized polyurethane acrylate binders in the pigment print paste for screen printing cotton and polyester fabrics and pigment fixation through the polymerization process of the binder by us...The use of the four new synthesized polyurethane acrylate binders in the pigment print paste for screen printing cotton and polyester fabrics and pigment fixation through the polymerization process of the binder by using the thermofixation technique as well as the UV curing technique was studied. The effect of changing time and temperature of thermofixation, and the time of UV curing on the color strength, and prints fastness properties were also studied. The results showed that, the newly synthesized polyurethane acrylate binders could be successfully used for pigment fixation on cotton and polyester using the two fixation techniques and in general their prints possessed better color strength values as compared to those obtained upon using the selected commercial binders.展开更多
The effects of graphite on temperature susceptibility of asphalt binders were investigated by penetration test,Ring & Ball softening point test and viscosity test.And penetration index(IP),viscosity-temperature su...The effects of graphite on temperature susceptibility of asphalt binders were investigated by penetration test,Ring & Ball softening point test and viscosity test.And penetration index(IP),viscosity-temperature susceptibility(SVT),and penetration-viscosity numbers(NPV) were introduced to evaluate the effects.The results show that the penetration,softening point and viscosity of asphalt binder increase with the increase of content of graphite.This means that the addition of graphite makes asphalts stiffer.The results from IP,NPV and SVT show that temperature susceptibility is reduced by the addition of graphite.展开更多
Shear resistance properties of the virgin bitumen and modified bitumen binders with Tafpack Super(TPS) modifier and SBS modified bitumen were discussed.Dynamic shear rheometer(DSR) was used to measure the laboratory c...Shear resistance properties of the virgin bitumen and modified bitumen binders with Tafpack Super(TPS) modifier and SBS modified bitumen were discussed.Dynamic shear rheometer(DSR) was used to measure the laboratory creep data for these binders over a wide range of constant shear stresses at 20 ℃ to characterize the shear creep behaviors of all kinds of asphalt binders,and the rutting test system was used to investigate the permanent deformation of porous asphalt mixtures using the above bitumen binders for a fixed compressive stress.The shear strain rate and shear creep modulus were used to characterize the shear creep behavior of the TPS modified bitumen,and the rutting test results were used to show the consistency of porous asphalt mixtures with the bitumen binders.Results indicate that a distinction of shear creep strain can be made among different contents of TPS modified bitumen at the same stress level,where the shear creep strain-time response curve of the SBS modified bitumen binder is between the curves of the 8% TPS and 12% TPS modified bitumen binders.The shear strain rate and the shear creep modulus of the TPS modified bitumen binders are obtained to compare with those of the SBS modified bitumen binder which results in the same trend as the shear creep strain-time response curve.Permanent deformation results of all the porous asphalt mixtures from the rutting test show reasonable agreement with the findings of the shear strain rates and shear creep modulus over the range of shear stress levels.展开更多
Some new an aqueous polyurethane acrylate (waterborne binder) based on polyethylene glycol with different M. wt. mixed with polyol were carried out. Seven different polyurethane acrylate co-polymers were prepared aimi...Some new an aqueous polyurethane acrylate (waterborne binder) based on polyethylene glycol with different M. wt. mixed with polyol were carried out. Seven different polyurethane acrylate co-polymers were prepared aiming at substituting the two hydroxyl groups of polyethylene glycol (6000, 12,000 and 20,000 g/mol) and two primary hydroxyl groups of polyol through their reaction with corresponding calculated amounts of either isophorone diisoyanate or toluene diisocyanate and caped the remaining isocyanate group with either hydroxy ethyl acrylate or hydroxy propyl methacrylate to get on the polyurethane acrylate polymers [PUA]. From DSC measurement the result of Tg of synthesized PUA are in range from -8.78℃ to 36.4℃. So they can classify as soft binders. The infrared spectra, rheological properties, viscosity measurement, the weight average molecular weight, of the synthesize binders were investigated.展开更多
Alkali activated binder, commonly known as geopolymer cement, has replaced Portland cement in the production of mortar and concrete globally over the past few years. The density, particle size distribution, and specif...Alkali activated binder, commonly known as geopolymer cement, has replaced Portland cement in the production of mortar and concrete globally over the past few years. The density, particle size distribution, and specific surface area (SSA) are important physical parameters affecting strength and durability of alkali activated binders. This study carried out tests for physical and chemical properties of the natural pozzolan and calcium hydroxide and then determines the influence of alkali solution (sodium silicate and sodium hydroxide) on strength development of natural pozzolan calcium hydroxide binders. The particle size distribution (PSD), relative densities (RD), and specific surface areas (SSA) of powder natural pozzolan and calcium hydroxide materials and for the mixture of natural pozzolan and calcium hydroxide were determined by using Blaine air permeability apparatus. The optimum proportion of 75% natural pozzolan and 25% calcium hydroxide was obtained which produces the compressive strength of 7.5 MPa at 28 days cured paste. The mixture of natural pozzolan and calcium hydroxide were further grinded at three different finenesses and the particle size gradation, specific densities, specific surface areas and mean particles sizes for the mixture were determined. The compressive strength of alkali activated binders increased with increasing curing period and fineness. The maximum compressive strength for 28 days cured specimens was 26.1 MPa which was obtained at a solution of 8 moles sodium hydroxide concentration. The test results showed that natural pozzolan materials can be used to make geopolymer binders for mortars and concretes. The geopolymer binders for mortars and concretes reduce green gas emission from cement factory but also it can be used to produce durable mortar and concrete with comparable strengths with mortars and concrete made from conventional Portland cement.展开更多
The microstructure and the mechanical properties of hardened mortars made of superplasticized composite binder containing shale ash and fly ash are investigated. The pozzolanic reaction consumes the oriented Ca (OH)2 ...The microstructure and the mechanical properties of hardened mortars made of superplasticized composite binder containing shale ash and fly ash are investigated. The pozzolanic reaction consumes the oriented Ca (OH)2 crystals, thus making the transition zone dense. Appropriately proportioning of shale ash and fly ash decreases the water requirement and increases the packing density of composite binder mortars, therefore increases their strength. Super plasticizer promotes the carbonation of calcium hydrates and the formation of ettringite that is transformed gradually into mono-sulfoaluminate hydrate in composite binder mortars. The joint action of fine complex mineral admixture and super plasticizer has a synergistic effect to improve the mechanical properties of composite binder.展开更多
The materials and physical properties of primary slurry are crucial to the surface quality of the finished castings,especially for high reactivity titanium alloys.The aim of this study is to investigate the influence ...The materials and physical properties of primary slurry are crucial to the surface quality of the finished castings,especially for high reactivity titanium alloys.The aim of this study is to investigate the influence of different binders on the physical properties of primary slurry for titanium alloy investment casting.The zirconia-based slurries with different binders were evaluated by comparing the parameters:viscosity,bulk density,plate weight, suspensibility,gel velocity and strength.The results indicate that a higher viscosity of binder leads to a higher viscosity and suspensibility of slurry with the same powder/binder ratio.The retention rate and thickness of primary layer increase with an increase in the viscosity of the slurry,and a higher retention rate is associated with a thicker primary layer.The gel velocity of the slurry is correlated with the gel velocity of the binder.The green strength and the baked strength of the primary layer are determined by the properties of the binder after gel and by the production of the binder after fired,respectively.展开更多
In the majority of rechargeable batteries including lithium-ion batteries,polyvinylidene fluoride(PVdF)binders are the most commonly used binder for both anode and cathode.However,using PVdF binder requires the organi...In the majority of rechargeable batteries including lithium-ion batteries,polyvinylidene fluoride(PVdF)binders are the most commonly used binder for both anode and cathode.However,using PVdF binder requires the organic solvent of N-methyl-2-pyrrolidone which is expensive,volatile,combustible,toxic,and has poor recyclability.Therefore,switching to aqueous electrode processing routes with non-toxic binders would provide a great leap forward towards the realization of ideally fully sustainable and environmentally friendly electrochemical energy storage devices.Various water-soluble binders(aqueous binders)were characterized and compared to the performance of conventional PVdF.Our study demonstrates that the electrochemical performance of Zn/MnO_(2) aqueous batteries is significantly improved by using sodium carboxymethyl cellulose(CMC)binder.In addition,CMC binders offer desirable adhesion,good wettability,homogeneous material distribution,and strong chemical stability at certain pH levels(3.5-5)without any decomposition for long-cycle life.展开更多
High temperature rheological properties of fiber modified asphalt binders and impact of the type and content on such properties were studied.Three types of fiber,including polyester(PET),polyacrylonitrile(PAN) and cel...High temperature rheological properties of fiber modified asphalt binders and impact of the type and content on such properties were studied.Three types of fiber,including polyester(PET),polyacrylonitrile(PAN) and cellulose(CEL),a control content(0%) and four levels of fiber content(2%,4%,6% and 8% by total asphalt binder mass) were used with asphalt binders.The high temperature rheological properties,consisting of complex modulus(G*) and phase angle δ,were measured using SHRP's dynamic shear rheometer(DSR) between 46-82 ℃.Experimental results indicate that the changes of G* and tan δ of fiber modified asphalt binders with the increase of test temperature tend to slow down,and the temperature susceptibility is improved obviously compared to that of original asphalt binder.Fiber modification results in the increase of rutting parameter(G*/sin δ) at high temperatures,the decrease of temperature susceptibility,and further improved high temperature performance of asphalt binder.An excellent correlation exhibits between fiber content and high temperature performance of asphalt binder.Moreover,fiber type also has different influences on the improvement of G*/sin δ,G*/sin δ of PET and PAN fiber asphalt binders are both higher than that of CEL fiber,but G*/sin δ of CEL fiber is still higher than that of original asphalt.However,there is a critical fiber content when fibers start to interact with each other.Therefore,based on the critical fiber content and economic consideration,the optimum fiber contents for various fiber-modified asphalt binders are obtained.展开更多
Fine Ni powder is often added to Co and bronze-based metal binder powders for diamond tool segments.Ni is a lower cost substitute for extra-fine Co powder and increases the toughness of Co-Fe diamond binders at the ex...Fine Ni powder is often added to Co and bronze-based metal binder powders for diamond tool segments.Ni is a lower cost substitute for extra-fine Co powder and increases the toughness of Co-Fe diamond binders at the expense of lower hardness and bend strength.In bronze-based diamond binder segments,Ni increases hardness and yield strength.Several grades of Ni powder are used commercially with both Co and bronze-based diamond binders.This paper compares properties of diamond binders containing carbonyl Ni powders including standard Inco(?) T255,T123 PM and T 110 PM.Binder materials were made by ball milling or dry mixing of the fine carbonyl Ni and Fe powders with either XF Co or air atomized bronze(90/10 Cu/Sn) powders.Co-based powder blends were hot pressed at 20～35 MPa and 700℃to 900℃.Bronze-based powder blends were cold pressed and sintered at 840℃.Apparent density,apparent hardness and bend strength(TRS) were compared for different binder compositions and processing conditions.展开更多
The chemical binder is one of the critical factors affecting ore agglomeration behavior and leaching efficiency.In this study,we in-vestigated the effect of the type of binder and mass fraction of the H_(2)SO_(4)solut...The chemical binder is one of the critical factors affecting ore agglomeration behavior and leaching efficiency.In this study,we in-vestigated the effect of the type of binder and mass fraction of the H_(2)SO_(4)solution used on the curing,soaking,and leaching behavior of ag-glomerations.The results revealed that Portland cement(3CaO·SiO_(2),2CaO·SiO_(2),and 3CaO·Al_(2)O_(3))was the optimal binder for obtaining a well-shaped,stable agglomeration structure.A higher extraction rate was achieved when using Portland cement than that obtained using sodi-um silicate,gypsum,or acid-proof cement.An excessive geometric mean size is not conducive to obtaining well-shaped agglomerations and desirable porosity.Using computed tomography(CT)and MATLAB,the porosity of two-dimensional CT images in sample concentrations L1-L3 was observed to increase at least 4.5vol%after acid leaching.Ore agglomerations began to be heavily destroyed and even to disinteg-rate when the sulfuric acid solution concentration was higher than 30 g/L,which was caused by the excessive accumulation of reaction products and residuals.展开更多
The lithium-sulfur battery(Li–S)is a promising energy storage system with many advantages over the commercialized lithium-ion battery.It has a high theoretical capacity of 1675 mAh gà1,a high theoretical energy ...The lithium-sulfur battery(Li–S)is a promising energy storage system with many advantages over the commercialized lithium-ion battery.It has a high theoretical capacity of 1675 mAh gà1,a high theoretical energy density(2600 Wh kgà1),and is eco-environmentally friendly.Although only a small amount is used(<10 wt%)in the electrode,binders may affect the discharge capacity and cycling stability of sulfur cathodes in the Li–S battery.In recent years,tremendous efforts have been made to develop functional binders with robust adhesive strength,fast ion/electron transportation,strong anchoring of lithium polysulfide(LiPS),and rapid redox kinetics,to improve capacity,coulombic efficiency,and energy density.This article reviews recent developments in binders for the Li–S battery.After briefly introducing the fundamentals of the Li–S battery,the desireable characteristics of binders are discussed based on the correlation between the functions of the binder molecules and the performance of the battery.Future challenges in developing promising binders and potential solutions are provided in the conclusion.展开更多
Pigment printing was carried out on lab scale by simple screen-printing techniques. By the application of acrylate and butadiene based binder, the crocking fastness, formaldehyde release and PVC migration of fabric pr...Pigment printing was carried out on lab scale by simple screen-printing techniques. By the application of acrylate and butadiene based binder, the crocking fastness, formaldehyde release and PVC migration of fabric printed with Imparon red KB pigment was evaluated. The effect of curing time on K/S values was also investigated. It has been found that butadiene based binder shows good performance in terms of crocking fastness, formaldehyde release and PVC migra-tion. It has also been observed that by increasing the binder concentration, the release of formaldehyde decreased and by increasing the curing time, the K/S values of printed fabric were decreased.展开更多
Sustainable concepts and practices have taken a centre-stage in different fields of studies and professions. This is because human activities continue to threaten the carrying capacity of earth resources as well as li...Sustainable concepts and practices have taken a centre-stage in different fields of studies and professions. This is because human activities continue to threaten the carrying capacity of earth resources as well as life basic needs such as shelter. Ghana, a developing nation, has been characterized with a boom in construction activities. In almost every constructional work, Portland cement remains the main binding agent that is used to bind aggregates together in a monolithic unit. The overdependence of the Ghanaian construction industry on Portland cement has contributed to huge sums of foreign exchange used to import cement ingredients, high cost of buildings and annual artificial shortages of cement which leads to high cost of the product. In this work, alternative binding agent—pozzolana cement, is reported with regards to the theory behind its utilization, laboratory results and practical applications. Results obtained from both the laboratory and the field works have shown that the future binder for the Ghanaian construction industry is pozzolana cement. CSIR-Building and Road Research Institute recommends it for the construction industry for use in various forms of construction such as block making, concrete and mortar works.展开更多
Miniature flares containing magnesium/sodium nitrate compounded with different binders were studied for increasing luminosity and luminous efficiency in various fuel oxidizer ratio and flare diameters.Unsaturated poly...Miniature flares containing magnesium/sodium nitrate compounded with different binders were studied for increasing luminosity and luminous efficiency in various fuel oxidizer ratio and flare diameters.Unsaturated polyester, Bisphenol-A epoxy resin, calcium resinate, and nitrocellulose were used as binders for construction the flares. Experimental results showed that luminous efficiency was higher for polyester based flares. Due to the difference in decomposition progress of various binders and the exothermic reaction between binder and oxidizer the luminous efficiency of the mixtures were 31000,28900, 27800 and 25100 cd respectively for polyester, epoxy, calcium resinate, and nitrocellulose. It was found that nitrocellulose as an energetic binder produces the highest light intensity in comparison to other binders, but the burning rate is higher and the burning time is lower than the other binders.Thermal analysis of four binders showed that the heat of reactions was directly related to the amount of light output and luminosity.展开更多
Asphalt binder is inevitably aged by ultraviolet(UV)light during its service period.UV ageing can significantly decrease the technical properties of asphalt binder.The sensitivity of asphalt to UV ageing and thermal-o...Asphalt binder is inevitably aged by ultraviolet(UV)light during its service period.UV ageing can significantly decrease the technical properties of asphalt binder.The sensitivity of asphalt to UV ageing and thermal-oxidative ageing differs,such that the UV ageing performance cannot be determined based on the thermal-oxidative ageing performance.Previous researches mainly focused on the chemical composite and technical performance changes of asphalt binder during UV ageing,and the UV light parameters effect on the ageing rate of asphalt binder.However,the theory for characterizing and explaining the development of UV ageing depth does not get too much attentions,and the UV ageing mechanism of asphalt binder is not very clear.Therefore,it cannot guide to develop or select the good methods or anti-UV ageing additives for asphalt binders.This paper focuses on the latest researches of the mechanisms and anti-ageing methods of asphalt binders.With the increase of UV ageing time,the UV ageing of asphalt binder develops gradually from the surface to inner part.There are various methods,such as low-penetration grade asphalt,less air void ratio,UV stabilizers and UV light absorbers,that can improve the UV ageing resistance of asphalt binders.A new theory of sensitive wavelengths of asphalt UV ageing is proposed,which can enrich the basic theory of asphalt UV ageing.Depending on this theory,different wavelengths of UV light have different ageing effects on asphalt binder.The composite anti-UV ageing additives with barrier and specific absorption effects on UV light is proposed,and may have better improvement effect on the anti-UV ageing performance of asphalt binder.展开更多
文摘Micro-sized silicon anodes have shown much promise in large-scale industrial production of high-energy lithium batteries.However,large volume change(>300%)of silicon anodes causes severe particle pulverization and the formation of unstable solid electrolyte interphases during cycling,leading to rapid capacity decay and short cycle life of lithium-ion batteries.When addressing such issues,binder plays key roles in obtaining good structural integrity of silicon anodes.Herein,we report a biopolymer composite binder composed of rigid poly(acrylic acid)(PAA)and flexible silk fibroin(SF)tailored for micro-sized silicon anodes.The PAA/SF binder shows robust gradient binding energy via chemical interactions between carboxyl and amide groups,which can effectively accommodate large volume change of silicon.This PAA/SF binder also shows much stronger adhesion force and improved binding towards high-surface/defective carbon additives,resulting in better electrochemical stability and higher coulombic efficiency,than conventional PAA binder.As such,micro-sized silicon/carbon anodes fabricated with novel PAA/SF binder exhibit much better cyclability(up to 500 cycles at 0.5 C)and enhanced rate capability compared with conventional PAA-based anodes.This work provides new insights into the design of functional binders for high-capacity electrodes suffering from large volume change for the development of nextgeneration lithium batteries.
基金supported by the National Natural Science Foundation of China(51275313)Shandong Province Transportation Science and Technology Project(2021B115)Shandong Jiaotong University School Fund(Z2019036).
文摘In typical metal foundry applications,sand casting is still the most used technology.The related binder plays a very important role as its performances can directly influence the quality of castings.Among many binders,glues of animal origin have attracted much attention in recent years due to their reduced environmental impact.How-ever,they display some drawbacks such as the tendency to coagulate easily at room temperature and a relatively low strength.In this study,a novel gas-hardening casting binder was prepared using an animal glue and anhy-drous potassium carbonate as a hydrolyzing agent to avoid undesired agglomeration.Moreover,sodium pyropho-sphate and furfuryl alcohol were exploited as modifiers to obtain a binder with a high compressive strength.The best modification conditions,determined by means of an orthogonal design matrix approach,were 4 g of Na2CO3,sodium pyrophosphate,furfuryl alcohol and animal glue with a ratio of 4:12:100,at 85°C and with a duration of 115 min,respectively.The viscosity of the mixture obtained under these optimized conditions was 1250 mPa⋅s.The compressive strength of the binder,hardened by CO_(2) gas,was 4.00 MPa.Its gas evolution at 850°C was 15 ml⋅g-1,and its residual strength after 10 min calculation at 800°C was 0.01 MPa,which is high enough to meet the requirement of core-making in foundry.Moreover,after hydrolysis and further modification,animal glue and modifiers displayed a grafting reaction and an esterification reaction,respectively,which made the adhesive network denser and improved its thermal stability.
基金Project (50075011) supported by the National Natural Science Foundation of China
文摘Thermal spraying of cermet coatings is widely used for protection of machining parts against wear and corrosion. These coatings consist of WC particles in metal binders such as Co, Cr and Ni. Three kinds of WC powders with different metal binders (Co, NiCr and CoCr) were sprayed by low power plasma spray system on Al-Si-Cu alloy substrate. Fundamental aspects of sprayed cermet coatings, including (i) the effects of binder type on the coating structure, (ii) the hardness and (iii) the microstructure, were investigated. All cermet coatings have the same phase structure such as WC and W2 C. However, the intensities of these phases are different in each coating, mainly due to the difference in solidification rate in each case. Moreover, the hardness measurements are found to be different in each coating. The results show that, binder type has a significant effect on the physical and mechanical properties of the sprayed coatings.
文摘The use of the four new synthesized polyurethane acrylate binders in the pigment print paste for screen printing cotton and polyester fabrics and pigment fixation through the polymerization process of the binder by using the thermofixation technique as well as the UV curing technique was studied. The effect of changing time and temperature of thermofixation, and the time of UV curing on the color strength, and prints fastness properties were also studied. The results showed that, the newly synthesized polyurethane acrylate binders could be successfully used for pigment fixation on cotton and polyester using the two fixation techniques and in general their prints possessed better color strength values as compared to those obtained upon using the selected commercial binders.
基金Project(NCET-05-0656) supported by Education Ministry for the New Century Excellent Talents,China
文摘The effects of graphite on temperature susceptibility of asphalt binders were investigated by penetration test,Ring & Ball softening point test and viscosity test.And penetration index(IP),viscosity-temperature susceptibility(SVT),and penetration-viscosity numbers(NPV) were introduced to evaluate the effects.The results show that the penetration,softening point and viscosity of asphalt binder increase with the increase of content of graphite.This means that the addition of graphite makes asphalts stiffer.The results from IP,NPV and SVT show that temperature susceptibility is reduced by the addition of graphite.
基金Project(NCET-05-0656) supported by Education Ministry for the New Century Excellent Talents,China
文摘Shear resistance properties of the virgin bitumen and modified bitumen binders with Tafpack Super(TPS) modifier and SBS modified bitumen were discussed.Dynamic shear rheometer(DSR) was used to measure the laboratory creep data for these binders over a wide range of constant shear stresses at 20 ℃ to characterize the shear creep behaviors of all kinds of asphalt binders,and the rutting test system was used to investigate the permanent deformation of porous asphalt mixtures using the above bitumen binders for a fixed compressive stress.The shear strain rate and shear creep modulus were used to characterize the shear creep behavior of the TPS modified bitumen,and the rutting test results were used to show the consistency of porous asphalt mixtures with the bitumen binders.Results indicate that a distinction of shear creep strain can be made among different contents of TPS modified bitumen at the same stress level,where the shear creep strain-time response curve of the SBS modified bitumen binder is between the curves of the 8% TPS and 12% TPS modified bitumen binders.The shear strain rate and the shear creep modulus of the TPS modified bitumen binders are obtained to compare with those of the SBS modified bitumen binder which results in the same trend as the shear creep strain-time response curve.Permanent deformation results of all the porous asphalt mixtures from the rutting test show reasonable agreement with the findings of the shear strain rates and shear creep modulus over the range of shear stress levels.
文摘Some new an aqueous polyurethane acrylate (waterborne binder) based on polyethylene glycol with different M. wt. mixed with polyol were carried out. Seven different polyurethane acrylate co-polymers were prepared aiming at substituting the two hydroxyl groups of polyethylene glycol (6000, 12,000 and 20,000 g/mol) and two primary hydroxyl groups of polyol through their reaction with corresponding calculated amounts of either isophorone diisoyanate or toluene diisocyanate and caped the remaining isocyanate group with either hydroxy ethyl acrylate or hydroxy propyl methacrylate to get on the polyurethane acrylate polymers [PUA]. From DSC measurement the result of Tg of synthesized PUA are in range from -8.78℃ to 36.4℃. So they can classify as soft binders. The infrared spectra, rheological properties, viscosity measurement, the weight average molecular weight, of the synthesize binders were investigated.
文摘Alkali activated binder, commonly known as geopolymer cement, has replaced Portland cement in the production of mortar and concrete globally over the past few years. The density, particle size distribution, and specific surface area (SSA) are important physical parameters affecting strength and durability of alkali activated binders. This study carried out tests for physical and chemical properties of the natural pozzolan and calcium hydroxide and then determines the influence of alkali solution (sodium silicate and sodium hydroxide) on strength development of natural pozzolan calcium hydroxide binders. The particle size distribution (PSD), relative densities (RD), and specific surface areas (SSA) of powder natural pozzolan and calcium hydroxide materials and for the mixture of natural pozzolan and calcium hydroxide were determined by using Blaine air permeability apparatus. The optimum proportion of 75% natural pozzolan and 25% calcium hydroxide was obtained which produces the compressive strength of 7.5 MPa at 28 days cured paste. The mixture of natural pozzolan and calcium hydroxide were further grinded at three different finenesses and the particle size gradation, specific densities, specific surface areas and mean particles sizes for the mixture were determined. The compressive strength of alkali activated binders increased with increasing curing period and fineness. The maximum compressive strength for 28 days cured specimens was 26.1 MPa which was obtained at a solution of 8 moles sodium hydroxide concentration. The test results showed that natural pozzolan materials can be used to make geopolymer binders for mortars and concretes. The geopolymer binders for mortars and concretes reduce green gas emission from cement factory but also it can be used to produce durable mortar and concrete with comparable strengths with mortars and concrete made from conventional Portland cement.
文摘The microstructure and the mechanical properties of hardened mortars made of superplasticized composite binder containing shale ash and fly ash are investigated. The pozzolanic reaction consumes the oriented Ca (OH)2 crystals, thus making the transition zone dense. Appropriately proportioning of shale ash and fly ash decreases the water requirement and increases the packing density of composite binder mortars, therefore increases their strength. Super plasticizer promotes the carbonation of calcium hydrates and the formation of ettringite that is transformed gradually into mono-sulfoaluminate hydrate in composite binder mortars. The joint action of fine complex mineral admixture and super plasticizer has a synergistic effect to improve the mechanical properties of composite binder.
文摘The materials and physical properties of primary slurry are crucial to the surface quality of the finished castings,especially for high reactivity titanium alloys.The aim of this study is to investigate the influence of different binders on the physical properties of primary slurry for titanium alloy investment casting.The zirconia-based slurries with different binders were evaluated by comparing the parameters:viscosity,bulk density,plate weight, suspensibility,gel velocity and strength.The results indicate that a higher viscosity of binder leads to a higher viscosity and suspensibility of slurry with the same powder/binder ratio.The retention rate and thickness of primary layer increase with an increase in the viscosity of the slurry,and a higher retention rate is associated with a thicker primary layer.The gel velocity of the slurry is correlated with the gel velocity of the binder.The green strength and the baked strength of the primary layer are determined by the properties of the binder after gel and by the production of the binder after fired,respectively.
基金the U.S.Department of Energy(DOE)Office of Electricity under contract No.57558PNNL is an operated by Battelle Memorial Institute for the DOE under contract DE-AC05-76RL01830.
文摘In the majority of rechargeable batteries including lithium-ion batteries,polyvinylidene fluoride(PVdF)binders are the most commonly used binder for both anode and cathode.However,using PVdF binder requires the organic solvent of N-methyl-2-pyrrolidone which is expensive,volatile,combustible,toxic,and has poor recyclability.Therefore,switching to aqueous electrode processing routes with non-toxic binders would provide a great leap forward towards the realization of ideally fully sustainable and environmentally friendly electrochemical energy storage devices.Various water-soluble binders(aqueous binders)were characterized and compared to the performance of conventional PVdF.Our study demonstrates that the electrochemical performance of Zn/MnO_(2) aqueous batteries is significantly improved by using sodium carboxymethyl cellulose(CMC)binder.In addition,CMC binders offer desirable adhesion,good wettability,homogeneous material distribution,and strong chemical stability at certain pH levels(3.5-5)without any decomposition for long-cycle life.
基金Project(2004243) supported by the Science and Technology Key Project of Hubei Province,China
文摘High temperature rheological properties of fiber modified asphalt binders and impact of the type and content on such properties were studied.Three types of fiber,including polyester(PET),polyacrylonitrile(PAN) and cellulose(CEL),a control content(0%) and four levels of fiber content(2%,4%,6% and 8% by total asphalt binder mass) were used with asphalt binders.The high temperature rheological properties,consisting of complex modulus(G*) and phase angle δ,were measured using SHRP's dynamic shear rheometer(DSR) between 46-82 ℃.Experimental results indicate that the changes of G* and tan δ of fiber modified asphalt binders with the increase of test temperature tend to slow down,and the temperature susceptibility is improved obviously compared to that of original asphalt binder.Fiber modification results in the increase of rutting parameter(G*/sin δ) at high temperatures,the decrease of temperature susceptibility,and further improved high temperature performance of asphalt binder.An excellent correlation exhibits between fiber content and high temperature performance of asphalt binder.Moreover,fiber type also has different influences on the improvement of G*/sin δ,G*/sin δ of PET and PAN fiber asphalt binders are both higher than that of CEL fiber,but G*/sin δ of CEL fiber is still higher than that of original asphalt.However,there is a critical fiber content when fibers start to interact with each other.Therefore,based on the critical fiber content and economic consideration,the optimum fiber contents for various fiber-modified asphalt binders are obtained.
文摘Fine Ni powder is often added to Co and bronze-based metal binder powders for diamond tool segments.Ni is a lower cost substitute for extra-fine Co powder and increases the toughness of Co-Fe diamond binders at the expense of lower hardness and bend strength.In bronze-based diamond binder segments,Ni increases hardness and yield strength.Several grades of Ni powder are used commercially with both Co and bronze-based diamond binders.This paper compares properties of diamond binders containing carbonyl Ni powders including standard Inco(?) T255,T123 PM and T 110 PM.Binder materials were made by ball milling or dry mixing of the fine carbonyl Ni and Fe powders with either XF Co or air atomized bronze(90/10 Cu/Sn) powders.Co-based powder blends were hot pressed at 20～35 MPa and 700℃to 900℃.Bronze-based powder blends were cold pressed and sintered at 840℃.Apparent density,apparent hardness and bend strength(TRS) were compared for different binder compositions and processing conditions.
基金This work was financially supported by the National Nat-ural Science Foundation for Excellent Youth of China(No.51722401)the State Key Research Development Program of China(No.2016YFC0600704)the Key Program of Na-tional Natural Science Foundation of China(No.51734001).
文摘The chemical binder is one of the critical factors affecting ore agglomeration behavior and leaching efficiency.In this study,we in-vestigated the effect of the type of binder and mass fraction of the H_(2)SO_(4)solution used on the curing,soaking,and leaching behavior of ag-glomerations.The results revealed that Portland cement(3CaO·SiO_(2),2CaO·SiO_(2),and 3CaO·Al_(2)O_(3))was the optimal binder for obtaining a well-shaped,stable agglomeration structure.A higher extraction rate was achieved when using Portland cement than that obtained using sodi-um silicate,gypsum,or acid-proof cement.An excessive geometric mean size is not conducive to obtaining well-shaped agglomerations and desirable porosity.Using computed tomography(CT)and MATLAB,the porosity of two-dimensional CT images in sample concentrations L1-L3 was observed to increase at least 4.5vol%after acid leaching.Ore agglomerations began to be heavily destroyed and even to disinteg-rate when the sulfuric acid solution concentration was higher than 30 g/L,which was caused by the excessive accumulation of reaction products and residuals.
基金supported by the National Natural Science Foundation of China(Grant No.52072118,51772089 and 21872046)the Youth 1000 Talent Program of China+4 种基金the Outstanding Youth Scientist Foundation of Hunan Province(Grant No.2018JJ1009)the Natural Science Foundation of Hunan Province(Grant No.2020JJ4174)the Provincial Science and Technology Innovation Platform and Talent Plan-Changsha,Zhuzhou and Xiangtan High-level Talents Accumulation Project(Grant No.2017XK2023)the Research and Development Plan of Key Areas in Hunan Province(Grant No.2019GK2235)the Key Research and Development Program of Ningxia(2020BDE03007)。
文摘The lithium-sulfur battery(Li–S)is a promising energy storage system with many advantages over the commercialized lithium-ion battery.It has a high theoretical capacity of 1675 mAh gà1,a high theoretical energy density(2600 Wh kgà1),and is eco-environmentally friendly.Although only a small amount is used(<10 wt%)in the electrode,binders may affect the discharge capacity and cycling stability of sulfur cathodes in the Li–S battery.In recent years,tremendous efforts have been made to develop functional binders with robust adhesive strength,fast ion/electron transportation,strong anchoring of lithium polysulfide(LiPS),and rapid redox kinetics,to improve capacity,coulombic efficiency,and energy density.This article reviews recent developments in binders for the Li–S battery.After briefly introducing the fundamentals of the Li–S battery,the desireable characteristics of binders are discussed based on the correlation between the functions of the binder molecules and the performance of the battery.Future challenges in developing promising binders and potential solutions are provided in the conclusion.
文摘Pigment printing was carried out on lab scale by simple screen-printing techniques. By the application of acrylate and butadiene based binder, the crocking fastness, formaldehyde release and PVC migration of fabric printed with Imparon red KB pigment was evaluated. The effect of curing time on K/S values was also investigated. It has been found that butadiene based binder shows good performance in terms of crocking fastness, formaldehyde release and PVC migra-tion. It has also been observed that by increasing the binder concentration, the release of formaldehyde decreased and by increasing the curing time, the K/S values of printed fabric were decreased.
文摘Sustainable concepts and practices have taken a centre-stage in different fields of studies and professions. This is because human activities continue to threaten the carrying capacity of earth resources as well as life basic needs such as shelter. Ghana, a developing nation, has been characterized with a boom in construction activities. In almost every constructional work, Portland cement remains the main binding agent that is used to bind aggregates together in a monolithic unit. The overdependence of the Ghanaian construction industry on Portland cement has contributed to huge sums of foreign exchange used to import cement ingredients, high cost of buildings and annual artificial shortages of cement which leads to high cost of the product. In this work, alternative binding agent—pozzolana cement, is reported with regards to the theory behind its utilization, laboratory results and practical applications. Results obtained from both the laboratory and the field works have shown that the future binder for the Ghanaian construction industry is pozzolana cement. CSIR-Building and Road Research Institute recommends it for the construction industry for use in various forms of construction such as block making, concrete and mortar works.
文摘Miniature flares containing magnesium/sodium nitrate compounded with different binders were studied for increasing luminosity and luminous efficiency in various fuel oxidizer ratio and flare diameters.Unsaturated polyester, Bisphenol-A epoxy resin, calcium resinate, and nitrocellulose were used as binders for construction the flares. Experimental results showed that luminous efficiency was higher for polyester based flares. Due to the difference in decomposition progress of various binders and the exothermic reaction between binder and oxidizer the luminous efficiency of the mixtures were 31000,28900, 27800 and 25100 cd respectively for polyester, epoxy, calcium resinate, and nitrocellulose. It was found that nitrocellulose as an energetic binder produces the highest light intensity in comparison to other binders, but the burning rate is higher and the burning time is lower than the other binders.Thermal analysis of four binders showed that the heat of reactions was directly related to the amount of light output and luminosity.
基金The authors acknowledge the financial supported by National Natural Science Foundation of China(No.52108415 and No.51808517)the National Key R&D Program of China(No.2018YFB1600200)+5 种基金the Key Technical Innovation Projects of Hubei Province(No.2019AEE023)the Key R&D Program of Hubei Province(No.2020BCB064)the State Key Laboratory of Silicate Materials for Architectures(Wuhan University of Technology)(No.SYSJJ2022-21),the Transportation Technology Project of Department of Transport of Hubei Province(No.2022-11-1-10)the European Union's Horizon 2020 Research and Innovation Programme Under the Marie Skłodowska-Curie Grant Agreement(No.101030767)the Scientific Research Fund Project of Wuhan Institute of Technology(No.K2021032)the Open Fund of National&Local Joint Engineering Laboratory of Traffic Civil Engineering Materials,Chongqing Jiaotong University(No.LHSYS-2020-004).
文摘Asphalt binder is inevitably aged by ultraviolet(UV)light during its service period.UV ageing can significantly decrease the technical properties of asphalt binder.The sensitivity of asphalt to UV ageing and thermal-oxidative ageing differs,such that the UV ageing performance cannot be determined based on the thermal-oxidative ageing performance.Previous researches mainly focused on the chemical composite and technical performance changes of asphalt binder during UV ageing,and the UV light parameters effect on the ageing rate of asphalt binder.However,the theory for characterizing and explaining the development of UV ageing depth does not get too much attentions,and the UV ageing mechanism of asphalt binder is not very clear.Therefore,it cannot guide to develop or select the good methods or anti-UV ageing additives for asphalt binders.This paper focuses on the latest researches of the mechanisms and anti-ageing methods of asphalt binders.With the increase of UV ageing time,the UV ageing of asphalt binder develops gradually from the surface to inner part.There are various methods,such as low-penetration grade asphalt,less air void ratio,UV stabilizers and UV light absorbers,that can improve the UV ageing resistance of asphalt binders.A new theory of sensitive wavelengths of asphalt UV ageing is proposed,which can enrich the basic theory of asphalt UV ageing.Depending on this theory,different wavelengths of UV light have different ageing effects on asphalt binder.The composite anti-UV ageing additives with barrier and specific absorption effects on UV light is proposed,and may have better improvement effect on the anti-UV ageing performance of asphalt binder.
