Photoinitiated inverse emulsion polymerization of sodium acrylate(AANa)in kerosene was carried out at room orlower temperature,using 2,2-dimethoxy-2-phenylacetophenone(DMPA)as the initiator.Kinetic investigations indi...Photoinitiated inverse emulsion polymerization of sodium acrylate(AANa)in kerosene was carried out at room orlower temperature,using 2,2-dimethoxy-2-phenylacetophenone(DMPA)as the initiator.Kinetic investigations indicated thatthe polymerization could be completed in about 30 min and produce polymer with high molecular weight(10~6～10~7).It wasfound that monomer droplets are the main sites for the polymerization(nucleation).With the increase of DMPAconcentration,polymerization rate(R_p)reaches a maximum value while molecular weight of the produced polymer has anadverse result,but the dependence of R_p on incident light intensity is similar.Influences of other parameters such asmonomer concentration,emulsifier content and reaction temperature,etc.were also studied.At lower pH values of waterphase,R_p depends strongly on the pH due to the electrostatic interaction between the ionized radicals and the monomer.Athigher pH,R_p shows a slight dependence on pH.展开更多
Stable high-solids-content acrylate emulsion were obtained with a nonionic polymerizable emulsifier allyloxy nonylphenoxy poly （ethyleneoxy） （10） ether （ANPEO10）, and a conventional emulsifier OP-10 as a referen...Stable high-solids-content acrylate emulsion were obtained with a nonionic polymerizable emulsifier allyloxy nonylphenoxy poly （ethyleneoxy） （10） ether （ANPEO10）, and a conventional emulsifier OP-10 as a reference sample. 1H NMR proves that the polymerizable emulsifier ANPEO10 has been incorporated into the resulted acrylate polymers. TEM demonstrates that there are some differences in the particle morphologies. AFM proves that the polymerizable emulsifier ANPEO10 migrating to the surface of the emulsion film was much less than the conventional emulsifier OP-10. The polymerizable emulsifier ANPEO10 can enhance the adhesion with glass plate compared to the conventional emulsifier. Furthermore, with increasing amount of emulsifier, the surface free energy of the films first decreased and then increased, and the adhesion with glass plate is initially enhanced and then attenuated. The water-resistance and solvent-resistance of the films prepared by the polymerizable emulsifier ANPEO10 are superior to those prepared by the conventional emulsifier OP-10.展开更多
The seeded semicontinuous emulsion multi-copolymerization of butyl acrylate (BA), 2-ethylhexyl acrylate (2EHA), methyl methacrylate (MMA), 2-hydroxyl propyl acrylate (HOPA) and acrylic acid (AA) was used to prepare th...The seeded semicontinuous emulsion multi-copolymerization of butyl acrylate (BA), 2-ethylhexyl acrylate (2EHA), methyl methacrylate (MMA), 2-hydroxyl propyl acrylate (HOPA) and acrylic acid (AA) was used to prepare the acrylic latexes with high-solid content. The effects of monomer emulsion feed rates (R(a)) and (R/E)(E) values, the ratio of emulsifier amount between the initial charge (R) and the addition monomer emulsion (E), on the polymerization reaction features, the viscosities, surface tensions,particle sizes and particle sizes distributions of latexes, T-g and the insoluble fractions of films, the 180 degrees peel strength, tack and holding power of pressure-sensitive adhesive (PSA) tapes, prepared from the latexes, were studied. Experimental study shows that the grafting and crosslinking fraction in the PSA tapes must be controlled within a suitable range to keep the balance of the 180 degrees peel strength, tack and holding power.展开更多
Introduction The emulsion of acrylate copolymers with actively functional groups have been widely developed and used as coating, adhesive and handling agent in spinning and weaving industry. Bessett, D. R. et al. stud...Introduction The emulsion of acrylate copolymers with actively functional groups have been widely developed and used as coating, adhesive and handling agent in spinning and weaving industry. Bessett, D. R. et al. studied the thermoset of N-(isobutoxymethyl) acrylamide by thermal evolution analysis and thermal gas chromatogram. Krejcar,展开更多
The formation mechanism of monodisperse polymer latex particles in the emulsifier-free emulsion polymerizationof methyl methacrylate and butyl acrylate with potassium persulfate as initiator was investigated. A multi-...The formation mechanism of monodisperse polymer latex particles in the emulsifier-free emulsion polymerizationof methyl methacrylate and butyl acrylate with potassium persulfate as initiator was investigated. A multi-step formationmechanism for the monodisperse polymer particles was proposed. The nucleation mechanism is considered to be thecoagulation of the precursor particles by homogeneous nucleation when the primary particles reach a critical size with highsurface charge density and sufficient stability. It had been proved by a special experiment that the early latex particles formedby the coagulation were stable. The primary particles grow by absorbing monomers and radicals in the polymerization systemand then become colloidally unstable again due to the understandable decrease of particle surface charge density, which leadsto the aggregation of the growing particles and the formation of larger latex pedicles therefrom. Aner the nucleation period,the preferential aggregation of the smaller particles in the propagation process leads to the change of the particles towards auniform size and narrower particle size distribution. The coexistence and competition of homogeneous nucleation,coagulation, propagation and aggregation result in the increase of the polydispersity index (U = D_(43)/D_(10)) in the first Stage,then its decrease in the later stage because of the competition of propagation and aggregation, and the gradual formation ofthe monodisperse particles.展开更多
Using butyl acrylate(BA),methyl methacrylate(MMA),methacrylic acid(MAA) and mixed emulsifier as raw materials,the self-crosslinked emulsion was prepared via pre-emulsified and semi-continuous seeded emulsion polymeriz...Using butyl acrylate(BA),methyl methacrylate(MMA),methacrylic acid(MAA) and mixed emulsifier as raw materials,the self-crosslinked emulsion was prepared via pre-emulsified and semi-continuous seeded emulsion polymerization technology in the presence of N-hydroxymethyl acrylamide and poly solidum maleate. The influence of mass ratio of BA to MMA,amount of N-hydroxymethyl acrylamide and poly solidum maleate on the rheological properties of the self-crosslinked emulsion was studied. Possible cross-linked mechanism of self-crosslinked monomer was investigated. And the relationship between emulsion viscosity and shear rate was investigated. The results show that the self-crosslinked acrylate emulsion with high elasticity can be synthesized when the mass fractions of BA is 60%,MMA is 40%,and added amount of N-hydroxymethyl acrylamide is 2.5%-3.0% and added amount of poly solidum maleate is 0.3%-0.4%. The self-crosslinkage process of N-hydroxymethyl acrylamide involves two steps. One is copolymerization of N-hydroxymethyl acrylamide and acrylate,the other is cross-linkage among polymer molecules via condensation reaction of methylol. The emulsion is of rheological properties of pseudo-plastic fluid and belongs to non-Newtonian fluid.展开更多
A silicone acrylate micro-emulsion of multipolymer was prepared by seed emulsion polymerization. The effects of polymerization process, emulsifier rate and amount, initiator rate and amount, polymerization temperature...A silicone acrylate micro-emulsion of multipolymer was prepared by seed emulsion polymerization. The effects of polymerization process, emulsifier rate and amount, initiator rate and amount, polymerization temperature, functional monomers, titration time on performances of emulsion have been discussed in detail.展开更多
Waterborne acrylic emulsions modified with organic siloxanes and aziridine crosslinker were synthesized and applied as coating of controlled release fertilizer. The free films were characterized and the nutrient relea...Waterborne acrylic emulsions modified with organic siloxanes and aziridine crosslinker were synthesized and applied as coating of controlled release fertilizer. The free films were characterized and the nutrient release profiles of the coated fertilizers were determined. The results show that methyl silicone oil and methylsilanolate sodium could not improve water resistance performance and glass transition temperature Tgof coatings, while the firmness is enhanced. Aziridine crosslinker improves the water resistance performance, firmness and Tg. Incorporation of methyl silicone oil and aziridine crosslinker gives an excellent aqueous acrylic emulsion for coated controlled release fertilizer, with the 30-day cumulative nutrient release reduced to 16% and an estimated nutrient release duration over 190 days. Therefore, this waterborne coating is promising to meet the requirements for controlled release of nutrient and environmental protection.展开更多
Polyvinyl alcohol (PVA) colloid stabilized Polyvinyl acetate (PVAc) based wood adhesive has poor performance in highly humid conditions. Currently, the addition of natural fillers in the wood adhesive is one of the mo...Polyvinyl alcohol (PVA) colloid stabilized Polyvinyl acetate (PVAc) based wood adhesive has poor performance in highly humid conditions. Currently, the addition of natural fillers in the wood adhesive is one of the most effective ways to enhance the performance of PVAc wood adhesive in highly moist conditions. Microcrystalline cellulose (MCC) are strong renewable, bio-based material and has great potential in a reinforcement of the polymeric matrix. Hence, the present work investigates the applicability of microcrystalline cellulose incorporated 3% and 5% in situ emulsion polymerization PVAc wood adhesives. Effect on physical, thermal and mechanical properties was studied by viscosity, pH, contact angle measurement, differential scanning calorimetry (DSC) and pencil hardness test of films. Emulsions with different proportions of MCC were prepared and the shear strength of the applied adhesive on wood was measured. The viscosity of the adhesives was increased by increasing the concentration of MCC. The mechanical properties like tensile strength of adhesives with MCC were measured by universal tensile machine (UTM). Thermal stability was studied by differential scanning calorimetry (DSC). The tensile shear strength demonstrates that MCC can improve bonding strength as compared to PVAc Homo based adhesive in the wet condition which was validated through a contact angle study. The hardness of PVAc films were also changed positively by the addition of MCC. Here, we studied the effect of the addition of different concentrations of MCC materials in situ polymerization of PVAc on their performance properties.展开更多
Well-defined nonionic hydrophilic ω-acryloyl poly(ethylene oxide) macro-monomer (PEO-A) has been prepared by living anionic polymerization of ethylene oxidewith diphenyl methyl potassium as the initiator and acryloyl...Well-defined nonionic hydrophilic ω-acryloyl poly(ethylene oxide) macro-monomer (PEO-A) has been prepared by living anionic polymerization of ethylene oxidewith diphenyl methyl potassium as the initiator and acryloyl chloride as the reaction termi-nating agent. The polymer was characterized by FTIR and SEC. The emulsifier-free emul-sion polymerization of methyl methacrylate (MMA) and n-butyl acrylate (BA) containingvarious concentrations of PEO-A was studied. In all cases stable emulsion coplymerizationsof MMA and BA were obtained. The stabilizing effect was found to be dependent on themolecular weight and the feed amount of the macromonomer.展开更多
Acrylate latex modified by vinyl triisopropoxy silane (C-1706) was synthesized by seeded emulsion polymerization with anionic emulsifier sodium dodecyl sulphonate(SDS) and nonionic emulsifier OP-10 as the multiple emu...Acrylate latex modified by vinyl triisopropoxy silane (C-1706) was synthesized by seeded emulsion polymerization with anionic emulsifier sodium dodecyl sulphonate(SDS) and nonionic emulsifier OP-10 as the multiple emulsifiers at (78±2) ℃. The effects of different factors, such as the emulsifier, C-1706 monomer and its feeding manner on the properties of acrylate latex modified by C-1706 were investigated. The particle size distribution and the structure, the configuration, the weather durability and stain resistance of copolymer latex were characterized by particle size analyzer, Fourier transform infrared spectroscopy (FT-IR), transmission electron microscope(TEM), scanning electron microscope(SEM) and ultraviolet aging instrument respectively. The results show that SDS to OP-10 as multiple emulsifiers can lead to coordinated efficiency, the optimal emulsifier dosage is 2.4%?3.2%(mass fraction), and the mass ratio of SDS to OP-10 is 1?1? 1?2. The seeded emulsion polymerization can effectively introduce a organic-siloxane bonding in a macromolecule inter polymer, and the obtained acrylate latex modified by organic-siloxane possesses narrow distribution of particle size with mean diameter of 51.8?76.6 nm and has the excellent properties in weather durability and stain-resistance especially.展开更多
Two novel fluorinated acrylate monomers 4a and 4b containing perfluorohexyl group were designed and synthesized starting from 4-allylanisole and perfluorohexyl iodide.The monomers 4a and 4b were then copolymerized wit...Two novel fluorinated acrylate monomers 4a and 4b containing perfluorohexyl group were designed and synthesized starting from 4-allylanisole and perfluorohexyl iodide.The monomers 4a and 4b were then copolymerized with octadecyl acrylate and 2-hydroxyethyl acrylate by emulsion polymerization to give copolymers PFA 1 and PFA 2 respectively.The co-polymers were characterized by FT-IR and their heat stability was measured by TGA.The surface properties of PFA 1 and PFA 2 were studied by applying on cotton fabrics.The treated cotton fabrics showed good water-repellent property,and the contact angles for water reached 142° for PFA 1 and 136° for PFA 2.展开更多
Styrene-acrylate latex with high glass transition temperature （T）, low minimum film forming temperature（MFT） and good stability was prepared via core-shell emulsion polymerization. With semicontinuous process, hig...Styrene-acrylate latex with high glass transition temperature （T）, low minimum film forming temperature（MFT） and good stability was prepared via core-shell emulsion polymerization. With semicontinuous process, high conversion rate of monomer and low gel rate were achieved. The weight ratio of core monomer to shell monomer was approximately 1.35. It is found that many factors such as emulsifiers, initiators, reaction temperature, pH value and polymerization technology have influences on the permormance of styrene-acrylate latex. The prepared latex was characterized by TEM and FTIR. The obtained latex with T of 20.57 ℃, MFT or5.0 ℃, and good stability, had good stability of film forming.展开更多
The copolymer of polyacrylate/polysiloxane for vibration damping materials was synthesized through emulsion polymerization. The effects of the amount of methyl methacrylate (MMA), polysiloxane containing vinyl, initia...The copolymer of polyacrylate/polysiloxane for vibration damping materials was synthesized through emulsion polymerization. The effects of the amount of methyl methacrylate (MMA), polysiloxane containing vinyl, initiator and emulsifier on the conversion, stability of polyacrylate/ polysiloxane emulsion were discussed when the emulsion was prepared by pre-emulsifying half continuous method. The graft copolymer has good vibration damping performance. The widest glass transition region of the copolymer spans 100℃, and the highest value of tand reached 2.0. The glass transition of the samples was examined by dynamic mechanical analysis (DMA). The vibration damping performance of the graft copolymer was affected by the amount of poly-vinyl dimethylsiloxane (PVMS).展开更多
In this article, AHPS (3 - allyloxy- 2 -hydrory- 1 -Propanesulfonate salt) wassynthesized to use in emulsifier-Ne emulsion polymerization of BA/BMa/MMA systemfor high solid content latexes. Storage stability klow beha...In this article, AHPS (3 - allyloxy- 2 -hydrory- 1 -Propanesulfonate salt) wassynthesized to use in emulsifier-Ne emulsion polymerization of BA/BMa/MMA systemfor high solid content latexes. Storage stability klow behavior of the latexes,morphology of the obtained latex particles, dynamic viscoelastic behavior, tensilestrength and water resistance properties of the resulted copolymers were investigated.The experimental results show that with the addition of AHPS, stability of the emulsionis greatly improved that there appears no apparent precipitation dunring thepolymerization and storage at room temperature for 6 months and at -10℃ for fourmonths. Flow of the latexes follows the Bingham body laws, diameter of the latexparticles is about 0.6μn, of which is larger than that of by conventional emulsionpolymerization(0.12μm). In addition, not only water resistance of the copolymersobtained by emulsifier-free emulsion polymerization is greatly improved, but alsotensile strength is obviously enhanced.展开更多
It is crucial to adapt the processing of forest bio-resources into biochemicals and bio-based ad-vanced materials in order to transform the current economic climate into a greener economy.Tall oil,as a by-product of t...It is crucial to adapt the processing of forest bio-resources into biochemicals and bio-based ad-vanced materials in order to transform the current economic climate into a greener economy.Tall oil,as a by-product of the Kraft process of wood pulp manufacture,is a promising resource for the extraction of various value-added products.Tall oil fatty acids-based multifunctional Michael acceptor acrylates were developed.The suitability of developed acrylates for polymerization with tall oil fatty acids-based Michael donor acetoacetates to form a highly cross-linked polymer ma-terial via the Michael addition was investigated.With this novel strategy,valuable chemicals and innovative polymer materials can be produced from tall oil in an entirely new way,making a significant contribution to the development of a forest-based bioeconomy.Two different tall oil-based acrylates were successfully synthesized and characterized.Synthesized acrylates were successfully used in the synthesis of bio-based thermoset polymers.Obtained polymers had a wide variety of mechanical and thermal properties(glass transition temperature from-12.1 to 29.6°C by dynamic mechanical analysis,Young’s modulus from 15 to 1760 MPa,and stress at break from 0.9 to 16.1 MPa).Gel permeation chromatography,Fourier-transform infrared(FT-IR)spectroscopy,matrix-assisted laser desorption/ionization-time of flight mass spectrometry,and nuclear magnetic resonance were used to analyse the chemical structure of synthesized acrylates.In addition,various titration methods and rheology tests were applied to characterize acrylates.The chemical composition and thermal and mechanical properties of the developed polymers were studied by using FT-IR,solid-state nuclear magnetic resonance,thermal gravimetric analy-sis,differential scanning calorimetry,dynamic mechanical analysis,and universal strength testing apparatus.展开更多
基金This work was supported by the Scientific Research Foundation for Youth(No.QN0404).
文摘Photoinitiated inverse emulsion polymerization of sodium acrylate(AANa)in kerosene was carried out at room orlower temperature,using 2,2-dimethoxy-2-phenylacetophenone(DMPA)as the initiator.Kinetic investigations indicated thatthe polymerization could be completed in about 30 min and produce polymer with high molecular weight(10~6～10~7).It wasfound that monomer droplets are the main sites for the polymerization(nucleation).With the increase of DMPAconcentration,polymerization rate(R_p)reaches a maximum value while molecular weight of the produced polymer has anadverse result,but the dependence of R_p on incident light intensity is similar.Influences of other parameters such asmonomer concentration,emulsifier content and reaction temperature,etc.were also studied.At lower pH values of waterphase,R_p depends strongly on the pH due to the electrostatic interaction between the ionized radicals and the monomer.Athigher pH,R_p shows a slight dependence on pH.
基金Funded by Ministry of Education (No.2006-KL-008),and Qingxin Hanerchem Chemical Technology Co,Ltd.
文摘Stable high-solids-content acrylate emulsion were obtained with a nonionic polymerizable emulsifier allyloxy nonylphenoxy poly （ethyleneoxy） （10） ether （ANPEO10）, and a conventional emulsifier OP-10 as a reference sample. 1H NMR proves that the polymerizable emulsifier ANPEO10 has been incorporated into the resulted acrylate polymers. TEM demonstrates that there are some differences in the particle morphologies. AFM proves that the polymerizable emulsifier ANPEO10 migrating to the surface of the emulsion film was much less than the conventional emulsifier OP-10. The polymerizable emulsifier ANPEO10 can enhance the adhesion with glass plate compared to the conventional emulsifier. Furthermore, with increasing amount of emulsifier, the surface free energy of the films first decreased and then increased, and the adhesion with glass plate is initially enhanced and then attenuated. The water-resistance and solvent-resistance of the films prepared by the polymerizable emulsifier ANPEO10 are superior to those prepared by the conventional emulsifier OP-10.
基金This work was supported by the National Natural Science Foundation of China
文摘The seeded semicontinuous emulsion multi-copolymerization of butyl acrylate (BA), 2-ethylhexyl acrylate (2EHA), methyl methacrylate (MMA), 2-hydroxyl propyl acrylate (HOPA) and acrylic acid (AA) was used to prepare the acrylic latexes with high-solid content. The effects of monomer emulsion feed rates (R(a)) and (R/E)(E) values, the ratio of emulsifier amount between the initial charge (R) and the addition monomer emulsion (E), on the polymerization reaction features, the viscosities, surface tensions,particle sizes and particle sizes distributions of latexes, T-g and the insoluble fractions of films, the 180 degrees peel strength, tack and holding power of pressure-sensitive adhesive (PSA) tapes, prepared from the latexes, were studied. Experimental study shows that the grafting and crosslinking fraction in the PSA tapes must be controlled within a suitable range to keep the balance of the 180 degrees peel strength, tack and holding power.
文摘Introduction The emulsion of acrylate copolymers with actively functional groups have been widely developed and used as coating, adhesive and handling agent in spinning and weaving industry. Bessett, D. R. et al. studied the thermoset of N-(isobutoxymethyl) acrylamide by thermal evolution analysis and thermal gas chromatogram. Krejcar,
文摘The formation mechanism of monodisperse polymer latex particles in the emulsifier-free emulsion polymerizationof methyl methacrylate and butyl acrylate with potassium persulfate as initiator was investigated. A multi-step formationmechanism for the monodisperse polymer particles was proposed. The nucleation mechanism is considered to be thecoagulation of the precursor particles by homogeneous nucleation when the primary particles reach a critical size with highsurface charge density and sufficient stability. It had been proved by a special experiment that the early latex particles formedby the coagulation were stable. The primary particles grow by absorbing monomers and radicals in the polymerization systemand then become colloidally unstable again due to the understandable decrease of particle surface charge density, which leadsto the aggregation of the growing particles and the formation of larger latex pedicles therefrom. Aner the nucleation period,the preferential aggregation of the smaller particles in the propagation process leads to the change of the particles towards auniform size and narrower particle size distribution. The coexistence and competition of homogeneous nucleation,coagulation, propagation and aggregation result in the increase of the polydispersity index (U = D_(43)/D_(10)) in the first Stage,then its decrease in the later stage because of the competition of propagation and aggregation, and the gradual formation ofthe monodisperse particles.
基金Project(2003B10506) supported by Guangdong Provincial Department of Science and Technology, China
文摘Using butyl acrylate(BA),methyl methacrylate(MMA),methacrylic acid(MAA) and mixed emulsifier as raw materials,the self-crosslinked emulsion was prepared via pre-emulsified and semi-continuous seeded emulsion polymerization technology in the presence of N-hydroxymethyl acrylamide and poly solidum maleate. The influence of mass ratio of BA to MMA,amount of N-hydroxymethyl acrylamide and poly solidum maleate on the rheological properties of the self-crosslinked emulsion was studied. Possible cross-linked mechanism of self-crosslinked monomer was investigated. And the relationship between emulsion viscosity and shear rate was investigated. The results show that the self-crosslinked acrylate emulsion with high elasticity can be synthesized when the mass fractions of BA is 60%,MMA is 40%,and added amount of N-hydroxymethyl acrylamide is 2.5%-3.0% and added amount of poly solidum maleate is 0.3%-0.4%. The self-crosslinkage process of N-hydroxymethyl acrylamide involves two steps. One is copolymerization of N-hydroxymethyl acrylamide and acrylate,the other is cross-linkage among polymer molecules via condensation reaction of methylol. The emulsion is of rheological properties of pseudo-plastic fluid and belongs to non-Newtonian fluid.
基金Ministry of Science and Technology of China for Major State Basic Research Projects (2002AA322020)
文摘A silicone acrylate micro-emulsion of multipolymer was prepared by seed emulsion polymerization. The effects of polymerization process, emulsifier rate and amount, initiator rate and amount, polymerization temperature, functional monomers, titration time on performances of emulsion have been discussed in detail.
基金Supported by the National 12th Five-Year Science and Technology Supporting Program(2011BAD11B01)the Research & Development Projects Cooperation Project of Chinese Academy of Sciences(YDJDBNJ-2012-023)
文摘Waterborne acrylic emulsions modified with organic siloxanes and aziridine crosslinker were synthesized and applied as coating of controlled release fertilizer. The free films were characterized and the nutrient release profiles of the coated fertilizers were determined. The results show that methyl silicone oil and methylsilanolate sodium could not improve water resistance performance and glass transition temperature Tgof coatings, while the firmness is enhanced. Aziridine crosslinker improves the water resistance performance, firmness and Tg. Incorporation of methyl silicone oil and aziridine crosslinker gives an excellent aqueous acrylic emulsion for coated controlled release fertilizer, with the 30-day cumulative nutrient release reduced to 16% and an estimated nutrient release duration over 190 days. Therefore, this waterborne coating is promising to meet the requirements for controlled release of nutrient and environmental protection.
文摘Polyvinyl alcohol (PVA) colloid stabilized Polyvinyl acetate (PVAc) based wood adhesive has poor performance in highly humid conditions. Currently, the addition of natural fillers in the wood adhesive is one of the most effective ways to enhance the performance of PVAc wood adhesive in highly moist conditions. Microcrystalline cellulose (MCC) are strong renewable, bio-based material and has great potential in a reinforcement of the polymeric matrix. Hence, the present work investigates the applicability of microcrystalline cellulose incorporated 3% and 5% in situ emulsion polymerization PVAc wood adhesives. Effect on physical, thermal and mechanical properties was studied by viscosity, pH, contact angle measurement, differential scanning calorimetry (DSC) and pencil hardness test of films. Emulsions with different proportions of MCC were prepared and the shear strength of the applied adhesive on wood was measured. The viscosity of the adhesives was increased by increasing the concentration of MCC. The mechanical properties like tensile strength of adhesives with MCC were measured by universal tensile machine (UTM). Thermal stability was studied by differential scanning calorimetry (DSC). The tensile shear strength demonstrates that MCC can improve bonding strength as compared to PVAc Homo based adhesive in the wet condition which was validated through a contact angle study. The hardness of PVAc films were also changed positively by the addition of MCC. Here, we studied the effect of the addition of different concentrations of MCC materials in situ polymerization of PVAc on their performance properties.
文摘Well-defined nonionic hydrophilic ω-acryloyl poly(ethylene oxide) macro-monomer (PEO-A) has been prepared by living anionic polymerization of ethylene oxidewith diphenyl methyl potassium as the initiator and acryloyl chloride as the reaction termi-nating agent. The polymer was characterized by FTIR and SEC. The emulsifier-free emul-sion polymerization of methyl methacrylate (MMA) and n-butyl acrylate (BA) containingvarious concentrations of PEO-A was studied. In all cases stable emulsion coplymerizationsof MMA and BA were obtained. The stabilizing effect was found to be dependent on themolecular weight and the feed amount of the macromonomer.
基金Project(2003B10506) supported by Science and Technology Department of Guangdong Province, China
文摘Acrylate latex modified by vinyl triisopropoxy silane (C-1706) was synthesized by seeded emulsion polymerization with anionic emulsifier sodium dodecyl sulphonate(SDS) and nonionic emulsifier OP-10 as the multiple emulsifiers at (78±2) ℃. The effects of different factors, such as the emulsifier, C-1706 monomer and its feeding manner on the properties of acrylate latex modified by C-1706 were investigated. The particle size distribution and the structure, the configuration, the weather durability and stain resistance of copolymer latex were characterized by particle size analyzer, Fourier transform infrared spectroscopy (FT-IR), transmission electron microscope(TEM), scanning electron microscope(SEM) and ultraviolet aging instrument respectively. The results show that SDS to OP-10 as multiple emulsifiers can lead to coordinated efficiency, the optimal emulsifier dosage is 2.4%?3.2%(mass fraction), and the mass ratio of SDS to OP-10 is 1?1? 1?2. The seeded emulsion polymerization can effectively introduce a organic-siloxane bonding in a macromolecule inter polymer, and the obtained acrylate latex modified by organic-siloxane possesses narrow distribution of particle size with mean diameter of 51.8?76.6 nm and has the excellent properties in weather durability and stain-resistance especially.
基金Programfor Changjiang Scholars and Innovative Research Teamin University,China(No.IRT0526)Shanghai Municipal Scientific Committee,China(No.08JC1400400)
文摘Two novel fluorinated acrylate monomers 4a and 4b containing perfluorohexyl group were designed and synthesized starting from 4-allylanisole and perfluorohexyl iodide.The monomers 4a and 4b were then copolymerized with octadecyl acrylate and 2-hydroxyethyl acrylate by emulsion polymerization to give copolymers PFA 1 and PFA 2 respectively.The co-polymers were characterized by FT-IR and their heat stability was measured by TGA.The surface properties of PFA 1 and PFA 2 were studied by applying on cotton fabrics.The treated cotton fabrics showed good water-repellent property,and the contact angles for water reached 142° for PFA 1 and 136° for PFA 2.
文摘Styrene-acrylate latex with high glass transition temperature （T）, low minimum film forming temperature（MFT） and good stability was prepared via core-shell emulsion polymerization. With semicontinuous process, high conversion rate of monomer and low gel rate were achieved. The weight ratio of core monomer to shell monomer was approximately 1.35. It is found that many factors such as emulsifiers, initiators, reaction temperature, pH value and polymerization technology have influences on the permormance of styrene-acrylate latex. The prepared latex was characterized by TEM and FTIR. The obtained latex with T of 20.57 ℃, MFT or5.0 ℃, and good stability, had good stability of film forming.
文摘The copolymer of polyacrylate/polysiloxane for vibration damping materials was synthesized through emulsion polymerization. The effects of the amount of methyl methacrylate (MMA), polysiloxane containing vinyl, initiator and emulsifier on the conversion, stability of polyacrylate/ polysiloxane emulsion were discussed when the emulsion was prepared by pre-emulsifying half continuous method. The graft copolymer has good vibration damping performance. The widest glass transition region of the copolymer spans 100℃, and the highest value of tand reached 2.0. The glass transition of the samples was examined by dynamic mechanical analysis (DMA). The vibration damping performance of the graft copolymer was affected by the amount of poly-vinyl dimethylsiloxane (PVMS).
文摘In this article, AHPS (3 - allyloxy- 2 -hydrory- 1 -Propanesulfonate salt) wassynthesized to use in emulsifier-Ne emulsion polymerization of BA/BMa/MMA systemfor high solid content latexes. Storage stability klow behavior of the latexes,morphology of the obtained latex particles, dynamic viscoelastic behavior, tensilestrength and water resistance properties of the resulted copolymers were investigated.The experimental results show that with the addition of AHPS, stability of the emulsionis greatly improved that there appears no apparent precipitation dunring thepolymerization and storage at room temperature for 6 months and at -10℃ for fourmonths. Flow of the latexes follows the Bingham body laws, diameter of the latexparticles is about 0.6μn, of which is larger than that of by conventional emulsionpolymerization(0.12μm). In addition, not only water resistance of the copolymersobtained by emulsifier-free emulsion polymerization is greatly improved, but alsotensile strength is obviously enhanced.
基金funded by the Latvian Council of Science,project“High bio-based content thermoset polymer foam development from plant origin oils (Bio-Mer)” (No.lzp-2020/1-0385)supported by ESF within Project"Strengthening of PhD students and academic personnel of Riga Technical University and BA School of Business and Finance in the strategic fields of specialization" (No 8.2.2.0/20/I/008)of the Specific Objective 8.2.2"To Strengthen Academic Staffof Higher Education Institutions in Strategic Specialization Areas"of the Operational Programme"Growth and Employment”supported by Riga Technical University’s Doctoral Grant programme.
文摘It is crucial to adapt the processing of forest bio-resources into biochemicals and bio-based ad-vanced materials in order to transform the current economic climate into a greener economy.Tall oil,as a by-product of the Kraft process of wood pulp manufacture,is a promising resource for the extraction of various value-added products.Tall oil fatty acids-based multifunctional Michael acceptor acrylates were developed.The suitability of developed acrylates for polymerization with tall oil fatty acids-based Michael donor acetoacetates to form a highly cross-linked polymer ma-terial via the Michael addition was investigated.With this novel strategy,valuable chemicals and innovative polymer materials can be produced from tall oil in an entirely new way,making a significant contribution to the development of a forest-based bioeconomy.Two different tall oil-based acrylates were successfully synthesized and characterized.Synthesized acrylates were successfully used in the synthesis of bio-based thermoset polymers.Obtained polymers had a wide variety of mechanical and thermal properties(glass transition temperature from-12.1 to 29.6°C by dynamic mechanical analysis,Young’s modulus from 15 to 1760 MPa,and stress at break from 0.9 to 16.1 MPa).Gel permeation chromatography,Fourier-transform infrared(FT-IR)spectroscopy,matrix-assisted laser desorption/ionization-time of flight mass spectrometry,and nuclear magnetic resonance were used to analyse the chemical structure of synthesized acrylates.In addition,various titration methods and rheology tests were applied to characterize acrylates.The chemical composition and thermal and mechanical properties of the developed polymers were studied by using FT-IR,solid-state nuclear magnetic resonance,thermal gravimetric analy-sis,differential scanning calorimetry,dynamic mechanical analysis,and universal strength testing apparatus.
