The carboxyl-functionalized graphene oxide(GO-COOH) is a kind of unique two-dimensional(2 D) material and possesses excellent nonlinear saturable absorption property and high water-solubility. In this paper, we prepar...The carboxyl-functionalized graphene oxide(GO-COOH) is a kind of unique two-dimensional(2 D) material and possesses excellent nonlinear saturable absorption property and high water-solubility. In this paper, we prepare saturable absorber(SA) device by depositing GO-COOH nanosheets aqueous solution on a D-shaped fiber. The modulation depth(MD) and saturable intensity of the SA are measured to be 9.6% and 19 MW/cm^2, respectively. By inserting the SA into the erbium-doped fiber(EDF) laser, a passively mode-locked EDF laser has been achieved with the spectrum center wavelength of 1562.76 nm. The pulse duration, repetition rate, and the signal-to-noise ratio(SNR) are 500 fs, 14.79 MHz, and 80 dB,respectively. The maximum average output power is measured to be 3.85 mW. These results indicate that the GO-COOH nanosheets SA can be used as a promising mode locker for the generation of ultrashort pulses.展开更多
A novel strategy was developed to prepare the methacrylic gelatin-dopamine(GelMA-DA)/Ag nanoparticles(NPs)/graphene oxide(GO) composite hydrogels with good biocompatibility,mechanical properties,and antibacterial acti...A novel strategy was developed to prepare the methacrylic gelatin-dopamine(GelMA-DA)/Ag nanoparticles(NPs)/graphene oxide(GO) composite hydrogels with good biocompatibility,mechanical properties,and antibacterial activity.Mussel-inspired DA was utilized to modify the GelMA molecules,which imparts good adhesive performance to the hydrogels.GO,interfacial enhancer,not only improves mechanical properties of the hydrogels,but also provides anchor sites for loading Ag NPs through numerous oxygencontaining functional groups on the surface.The experimental results show that the GelMA/Ag NPs/GO hydrogels have good biocompatibility,and exhibit a swelling rate of 202±16%,the lap shear strength of 147±17 kPa,and compressive modulus of 136±53 kPa,in the case of the Ag NPs/GO content of 2 mg/mL.Antibacterial activity of the hydrogels against both gram-negative and gram-positive bacteria is dependent on the Ag NPs/GO content derived from the release of Ag^(+).Furthermore,the GelMA/Ag NPs/GO hydrogels possess good adhesive ability,which is resistant to highly twisted state when stuck on the surface of pigskin.These results demonstrate promising potential of the GelMA-DA/Ag NPs/GO hydrogels as wound dressings for biomedical applications in clinical and emergent treatment.展开更多
Graphene oxide(GO)as a new nano-enhancer in cement-based materials has gained wide attention.However,GO is easy to aggregate in alkaline cement mortar with poor dispersibility.This hinders its application in practical...Graphene oxide(GO)as a new nano-enhancer in cement-based materials has gained wide attention.However,GO is easy to aggregate in alkaline cement mortar with poor dispersibility.This hinders its application in practical infrastructure construction.In this work,GO-M18 polycarboxylate compound superplasticizer(GM)were obtained by compounding the M18 polycarboxylate superplasticizer with GO solution at different mass ratios.The dispersion of GM in alkaline solution was systematically studied.The phases and functional groups of GM were characterized by XRD and FTIR.The effects of GM on the cement mortar hydration and the formation of microstructure were investigated by measuring the heat of hydration,MIP,TG/DSC,and SEM.The results show that the long-chain structure of the M18 polycarboxylate superplasticizer can increase the interlayer spacing of GO and weaken the force between GO sheets.The modified GO can be uniformly dispersed in the cement slurry.GM can accelerate the early hydration process of cement,which can increase the content of Ca(OH)2 and decrease the grain size.It can optimize the pore size distribution of cement-based materials,increase the density of harmless and less harmful pores,thereby improving mechanical properties.Such methods can transform traditional cement-based materials into stronger,more durable composites,which prolong the life of cement-based materials and reduce the amount of cement used for later maintenance.This provides an idea for achieving sustainability goals in civil engineering.展开更多
Graphene oxide(GO)is regarded as a promising candidate to construct solar absorbers for addressing freshwater crisis,but the easy delamination of GO in water poses a critical challenge for practical solar desalination...Graphene oxide(GO)is regarded as a promising candidate to construct solar absorbers for addressing freshwater crisis,but the easy delamination of GO in water poses a critical challenge for practical solar desalination.Herein,we improve the stability of GO membranes by a self-crosslinking poly(ionic liquid)(PIL)in a mild condition,which crosslinks neighbouring GO nanosheets without blemishing the hydrophilic structure of GO.By further adding carbon nanotubes(CNTs),the sandwiched GO/CNT@PIL(GCP)membrane displays a good stability in pH=1 or 13 solution even for 270 days.The molecular dynamics simulation results indicate that the generation of water nanofluidics in nanochannels of GO nanosheets remarkably reduces the water evaporation enthalpy in GCP membrane,compared to bulk water.Consequently,the GCP membrane exhibits a high evaporation rate(1.87 kg m^(-2)h^(-1))and displays stable evaporation rates for 14 h under 1 kW m^(-2)irradiation.The GCP membrane additionally works very well when using different water sources(e.g.,dye-polluted water)or even strong acidic solution(pH=1)or basic solution(pH=13).More importantly,through bundling pluralities of GCP membrane,an efficient solar desalination device is developed to produce drinkable water from seawater.The average daily drinkable water amount in sunny day is 10.1 kg m^(-2),which meets with the daily drinkable water needs of five adults.The high evaporation rate,long-time durability and good scalability make the GCP membrane an outstanding candidate for practical solar seawater desalination.展开更多
Reduced graphene oxide(rGO)aerogels are emerging as very attractive scaffolds for high-performance electromagnetic wave absorption materials(EWAMs)due to their intrinsic conductive networks and intricate interior micr...Reduced graphene oxide(rGO)aerogels are emerging as very attractive scaffolds for high-performance electromagnetic wave absorption materials(EWAMs)due to their intrinsic conductive networks and intricate interior microstructure,as well as good compatibility with other electromagnetic(EM)components.Herein,we realized the decoration of rGO aerogel with Mo_(2)C nanoparticles by sequential hydrothermal assembly,freeze-drying,and high-temperature pyrolysis.Results show that Mo_(2)C nanoparticle loading can be easily controlled by the ammonium molybdate to glucose molar ratio.The hydrophobicity and thermal insulation of the rGO aerogel are effectively improved upon the introduction of Mo_(2)C nanoparticles,and more importantly,these nanoparticles regulate the EM properties of the rGO aerogel to a large extent.Although more Mo_(2)C nanoparticles may decrease the overall attenuation ability of the rGO aerogel,they bring much better impedance matching.At a molar ratio of 1:1,a desirable balance between attenuation ability and impedance matching is observed.In this context,the Mo_(2)C/r GO aerogel displays strong reflection loss and broad response bandwidth,even with a small applied thickness(1.7 mm)and low filler loading(9.0wt%).The positive effects of Mo_(2)C nanoparticles on multifunctional properties may render Mo_(2)C/r GO aerogels promising candidates for high-performance EWAMs under harsh conditions.展开更多
Promising room-temperature sodium-sulfur(RT Na-S)battery systems rely on purposely designed highperforming and low-cost electrode materials.Nevertheless,there are the challenges of irreversible dissolution and slow re...Promising room-temperature sodium-sulfur(RT Na-S)battery systems rely on purposely designed highperforming and low-cost electrode materials.Nevertheless,there are the challenges of irreversible dissolution and slow redox kinetics of NaPSs in the complete discharge of sulfur capacity.Herein,engineered CoMoO_(4)in reduced graphene oxide(CoMoO_(4)@rGO)is reported as a class of superior cathode hosts for RT Na-S batteries.The CoMoO_(4)@rGO matrix is designed to facilitate the reversible sodiation and desodiation of sulfur,considering the strong chemisorption between sulfur(and short-chain sodium sulfides)and CoMoO_(4),which alleviates the shuttle effect of sodium sulfides and accelerates the electrochemical reaction rate at RT.The obtained S/CoMoO_(4)@rGO cathode with~52%S loading exhibits a high capacity of520.1 mA h g^(-1)after 100 cycles at 0.1 A g^(-1).Moreover,an enhanced long-term performance at high current densities(212.2 mA h g^(-1)at 4 A g^(-1)over 1000 cycles)with high Coulombic efficiency(~100%)is also achieved.This work demonstrates a novel multifunctional additive for RT Na-S battery cathodes,which is expected to promote the long-waited development towards practical applications of RT Na-S batteries.展开更多
Currently available commercial nerve guidance conduits have been applied in the repair of peripheral nerve defects.However,a conduit exhibiting good biocompatibility remains to be developed.In this work,a series of ch...Currently available commercial nerve guidance conduits have been applied in the repair of peripheral nerve defects.However,a conduit exhibiting good biocompatibility remains to be developed.In this work,a series of chitosan/graphene oxide(GO)films with concentrations of GO varying from 0-1 wt%(collectively referred to as CHGF-n)were prepared by an electrodeposition technique.The effects of CHGF-n on proliferation and adhesion abilities of Schwann cells were evaluated.The results showed that Schwann cells exhibited elongated spindle shapes and upregulated expression of nerve regeneration-related factors such as Krox20(a key myelination factor),Zeb2(essential for Schwann cell differentiation,myelination,and nerve repair),and transforming growth factorβ(a cytokine with regenerative functions).In addition,a nerve guidance conduit with a GO content of 0.25%(CHGFC-0.25)was implanted to repair a 10-mm sciatic nerve defect in rats.The results indicated improvements in sciatic functional index,electrophysiology,and sciatic nerve and gastrocnemius muscle histology compared with the CHGFC-0 group,and similar outcomes to the autograft group.In conclusion,we provide a candidate method for the repair of peripheral nerve defects using free-standing chitosan/GO nerve conduits produced by electrodeposition.展开更多
Intercalation of insulating materials between epitaxial graphene and the metal substrates is highly demanded to restore the intrinsic properties of graphene,and thus essential for the graphene-based devices.Here we de...Intercalation of insulating materials between epitaxial graphene and the metal substrates is highly demanded to restore the intrinsic properties of graphene,and thus essential for the graphene-based devices.Here we demonstrate a successful solution for the intercalation of hafnium oxide into the interface between full-layer graphene and Ir(111)substrate.We first intercalate hafnium atoms beneath the epitaxial graphene.The intercalation of the hafnium atoms leads to the variation of the graphene moire superstructure periodicity,which is characterized by low-energy electron diffraction(LEED)and lowtemperature scanning tunneling microscopy(LT-STM).Subsequently,we introduce oxygen into the interface,resulting in oxidization of the intercalated hafnium.STM and Raman's characterizations reveal that the intercalated hafnium oxide layer could effectively decouple the graphene from the metallic substrate,while the graphene maintains its high quality.Our work suggests a high-k dielectric layer has been successfully intercalated between high-quality epitaxial graphene and metal substrate,providing a platform for applications of large-scale,high-quality graphene for electronic devices.展开更多
Graphene oxide(GO) channels exhibit unique mass transport behaviors due to their flexibility, controllable thinness and extraordinary physicochemical properties, enabling them to be widely used for adsorption and memb...Graphene oxide(GO) channels exhibit unique mass transport behaviors due to their flexibility, controllable thinness and extraordinary physicochemical properties, enabling them to be widely used for adsorption and membrane separation. Nevertheless, the adsorption behavior of nanosized contaminants within the channels of GO membrane has not been fully discussed. In this study, we fabricated a GO membrane(PGn, where n represents the deposition cycles of GO) with multi channels via the crosslinking of GO and multibranched poly(ethyleneimine)(PEI). Phenol was used as molecular probe to determine the correlations between dynamic adsorption behavior and structural parameters of the multilevel GO/PEI membrane. PG8 shows higher adsorption capacities and affinity, which is predominantly attributed to the multichannel structure providing a large specific surface for phenol adsorption, enhancing the accessibility of active sites for phenol molecules and the transport of phenol. Density functional theory calculations demonstrate that the adsorption mechanism of phenol within GO channel is energetically oriented by hydrogen bonds, which is dominated by oxygen-containing groups compared to amino groups. Particularly, the interfaces which facilitate strong π-π interaction and hydrogen bonds maybe the most active regions. Moreover, the as-prepared PG8 membrane showed outstanding performance for other contaminants such as methyl orange and Cr(VI). It is anticipated that this study will have implications for design of GO-related environmental materials with enhanced efficiency.展开更多
In this paper, we present a proof-of-concept study of the enhancement of photocatalytic activity via a combined strategy of fabricating a visible-light responsive ternary heterostructure and improving overall photosta...In this paper, we present a proof-of-concept study of the enhancement of photocatalytic activity via a combined strategy of fabricating a visible-light responsive ternary heterostructure and improving overall photostability by incorporating magnetic zinc oxide/graphene/iron oxide (ZGF). A solvothermal approach was used to synthesize the catalyst. X-ray diffraction (XRD), scanning electron microscopic, energy dispersive X-ray, transmission electron microscopic, vibrating sample magnetometric, and ultraviolet–visible diffuse reflectance spectroscopic techniques were used to characterize the synthesized samples. The obtained optimal Zn(NO_(3))_(2) concentration, temperature, and heating duration were 0.10 mol/L, 600℃, and 1 h, respectively. The XRD pattern revealed the presence of peaks corresponding to zinc oxide, graphene, and iron oxide, indicating that the ZGF catalyst was effectively synthesized. Furthermore, when the developed ZGF was used for methylene blue dye degradation, the optimum irradiation time, dye concentration, catalyst dosage, irradiation intensity, and solution pH were 90 min, 10 mg/L, 0.03 g/L, 100 W, and 8.0, respectively. Therefore, the synthesized ZGF system could be used as a catalyst to degrade dyes in wastewater samples. This hybrid nanocomposite consisting of zinc oxide, graphene, and iron oxide could also be used as an effective photocatalytic degrader for various dye pollutants.展开更多
Asymmetrically modified Janus graphene oxide(JGO)has attracted great attention due to its unique physical chemistry properties and wide applications.The modification degree of Janus nanosheets inevitably affects their...Asymmetrically modified Janus graphene oxide(JGO)has attracted great attention due to its unique physical chemistry properties and wide applications.The modification degree of Janus nanosheets inevitably affects their interfacial activity,which is essential for their performances in enhanced oil recovery(EOR).In this study,the interfacial properties of Janus graphene oxide(JGO)with various modification degrees at liquid-liquid and liquid-solid interfaces were systematically evaluated via the measurements of interfacial tension(IFT),dilatational modulus,contact angle,and EOR efficiency was further assessed by core flooding tests.It is found that JGO-5 with higher modification degree exhibits the greater ability to reduce IFT(15.16 mN/m)and dilatational modulus(26 mN/m).Furthermore,JGO can construct interfacial and climbing film with the assistance of hydrodynamic power to effectively detach the oil from the rock surface and greatly enhance oil recovery.Moderately modified JGO-2 can highly improve recovery of residual crude oil(11.53%),which is regarded as the promising EOR agent in practical application.The present study firstly focuses on the effects of modification degrees on the JGO interfacial properties and proposes diverse EOR mechanisms for JGO with different modification degrees.展开更多
This paper investigates the effects of pH on stability and thermal properties of copper oxide(CuO),graphene oxide(GO),and their hybrid nanofluid(HNF)at different mixing ratios.Initially,sol-gel and Hummer’s method wa...This paper investigates the effects of pH on stability and thermal properties of copper oxide(CuO),graphene oxide(GO),and their hybrid nanofluid(HNF)at different mixing ratios.Initially,sol-gel and Hummer’s method was employed for the synthesis of CuO and GO nanoparticles(NPs),and they are characterized with various techniques.The effects of two different surfactants were analyzed on nanofluid’s(NF’s)stability at different pH values.The properties like thermal conductivity(TC)and viscosity(VST)of NFs were measured at different volume concentration(0.1 vol%to 1.0 vol%)and temperature range of 30-60℃,respectively.The TC and VST of GO/CuO(50:50)HNF are higher than that of GO/CuO(20:80).The figure of merit(FOM)is determined for the studied HNFs.The correlations were presented to calculate the TC as well as VST of HNFs.Two modern novel machine learning-based ensemble approaches were employed for predictive model development for TC and VST of considered HNFs.The comparison of prognostic models with Taylor’s diagram revealed that Bayesian optimized support vector machine(BoASVM)was superior to Bayesian optimized boosted regression trees(BoA-BRT)for both TC and VST models.展开更多
In the present study, polyethersulfone based nanohybrid membranes were effectively fabricated by incorporating graphene oxide(GO) and hydrotalcite(HT) nanosheets into the membrane structure. HT was prepared to overcom...In the present study, polyethersulfone based nanohybrid membranes were effectively fabricated by incorporating graphene oxide(GO) and hydrotalcite(HT) nanosheets into the membrane structure. HT was prepared to overcome the irreversible agglomeration behavior of GO at a high concentration which affects the performance of the membranes. In particular, the shedding of HT in formamide provides a two-dimensional nanosheet with a higher positive charge density to prevent the restacking of GO nanosheets. Here, exfoliated GO and HT with different combinations(1:1, 1:2 and 1:3) were infused in the membrane matrix to treat lead-acid battery effluent effectively. Finally, the hybrid membranes were characterized for hydrophilicity, mechanical strength and pure water flux. In combination with the superior properties of GO and HT, the prepared hybrid membranes can be used as effectively to improve the separation and permeation performance. The phase inversion process eliminated the leaching of nanoparticles from the membrane matrix. The reusability of the hybrid membrane was achieved using0.1 mol·L^(-1)NaOH solution and reused without significant reduction in lead removal efficiency. The cost analysis of the membrane was also estimated from the lab study. Therefore, the present study suggested the selective and sustainable treatment of lead from a real-life effluent.展开更多
Practical applications of diverse flexible wearable electronics require electrochemical energy storage(EES)devices with multiple configurations.Moreover,to fabricate flexible EES devices with high energy density and s...Practical applications of diverse flexible wearable electronics require electrochemical energy storage(EES)devices with multiple configurations.Moreover,to fabricate flexible EES devices with high energy density and stability,organic integration from electrode design to device assembly is required.To address these challenges,a free-standing reduced graphene oxide(rGO)/carbon film with a unique sandwich structure has been designed via the assistance of vacuum-assistant filtration for lithium-ion capacitors(LICs).The graphene acts as not only a binder to construct a three-dimensional conductive network but also an active material to provide additional capacitive lithium storage sites,thus enabling fast ion/electron transport and improving the capacity.The designed rGO/hard carbon(rGO/HC)and rGO/activated carbon(rGO/AC)free-standing films exhibit enhanced specific capacities(513.7 mA h g^(-1)for rGO/HC and 102.8 mA h g^(-1)for rGO/AC)and excellent stability.Moreover,the integrated flexible quasi-solid-state rGO/AC//rGO/HC LIC devices possess a maximum energy density of 138.3 Wh kg^(-1),a high power density of 11 kW kg^(-1),and improved cycling performance(84.4%capacitance maintained after 10,000 cycles),superior to the AC//HC LIC(43.5%retention).Such a strategy enlightens the development of portable flexible LICs.展开更多
Water pollution regarding dyes and heavy metal ions is crucial facing the world.How to effectively separate these contaminants from water has been a key issue.Graphene oxide(GO)promises the greenwater world as a long-...Water pollution regarding dyes and heavy metal ions is crucial facing the world.How to effectively separate these contaminants from water has been a key issue.Graphene oxide(GO)promises the greenwater world as a long-lasting spotlight adsorbent material and therefore,harnessing GO has been the research hotspot for over a decade.The state of GO as well as its surface functional groups plays an important role in adsorption.And the way of preparation and structural modification matters to the performance of GO.In this review,the significance of the state of existence of stock GO and surface functional groups is explored in terms of preparation,structural modification,and adsorption.Besides,various adsorbates for GO adsorption are also involved,the discussion of which is rarely established elsewhere.展开更多
In this study,three-dimensional porous magnesium ferrite/titanium dioxide/reduced graphene oxide(Mg Fe_2O_(4)-GM/TiO_(2)/rGO(MGTG))was successfully synthesized via green and hydrothermal-supported co-precipitation met...In this study,three-dimensional porous magnesium ferrite/titanium dioxide/reduced graphene oxide(Mg Fe_2O_(4)-GM/TiO_(2)/rGO(MGTG))was successfully synthesized via green and hydrothermal-supported co-precipitation methods using the extract of Garcinia mangostana(G.mangostana)as a reducing agent.The characterization results indicate the successful formation of the nano/micro Mg Fe_(2)O_(4)(MFO)and TiO_(2) on the structure of the reduced graphene oxide(rGO),which can also act as efficient support,alleviating the agglomeration of the nano/micro MFO and TiO_(2).The synergic effects of the adsorption and photodegradation activity of the material were investigated according to the removal of crystal violet(CV)under ultraviolet light.The effects of catalyst dosage,CV concentration,and p H on the CV removal efficiency of the MGTG were also investigated.According to the results,the CV photodegradation of the MGTG-200 corresponded to the pseudo-first-order kinetic model.The reusability of the material after 10 cycles also showed a removal efficiency of 92%.This happened because the materials can easily be recollected using external magnets.In addition,according to the effects of different free radicals·O_(2)^(-),h^(+),and·OH on the photodegradation process,the photocatalysis mechanism of the MGTG was also thoroughly suggested.The antibacterial efficiency of the MGTG was also evaluated according to the inhibition of the Gram-positive bacteria strain Staphylococcus aureus(S.aureus).Concurrently,the antibacterial mechanism of the fabricated material was also proposed.These results confirm that the prepared material can be potentially employed in a wide range of applications,including wastewater treatment and antibacterial activity.展开更多
Lithium-sulfur(Li-S) batteries can provide far higher energy density than currently commercialized lithium ion batteries, but challenges remain before it they are used in practice.One of the challenges is the shuttle ...Lithium-sulfur(Li-S) batteries can provide far higher energy density than currently commercialized lithium ion batteries, but challenges remain before it they are used in practice.One of the challenges is the shuttle effect that originates from soluble intermediates, like lithium polysulfides. To address this issue, we report a novel laminar composite, N,O-carboxymethyl chitosan-reduced graphene oxide(CC-rGO), which is manufactured via the self-assembly of CC onto GO and subsequent reduction of GO under an extreme condition of 1 Pa and-50°C. The synthesized laminar CC-rGO composite is mixed with acetylene black(AB) and coated on a commercial polypropylene(PP) membrane, resulting in a separator(CC-rGO/AB/PP) that can not only completely suppress the polysulfides penetration, but also can accelerate the lithium ion transportation, providing a Li-S battery with excellent cyclic stability and rate capability. As confirmed by theoretic simulations, this unique feature of CC-rGO is attributed to its strong repulsive interaction to polysulfide anions and its benefit for fast lithium ion transportation through the paths paved by the heteroatoms in CC.展开更多
The doping of functionalized graphene oxide(GO)in the membranes becomes a promising method for improving the performance of high-temperature proton exchange membrane fuel cells(HT-PEMFC).Phosphonated graphene oxide(PG...The doping of functionalized graphene oxide(GO)in the membranes becomes a promising method for improving the performance of high-temperature proton exchange membrane fuel cells(HT-PEMFC).Phosphonated graphene oxide(PGO)with a P/O ratio of 8.5%was quickly synthesised by one-step electrochemical exfoliation based on a three-dimensiaonal(3D)printed reactor and natural graphite flakes.Compared with the GO prepared by the two-step electrochemical exfoliation method,the PGO synthesized by the one-step electrochemical exfoliation can better improve the performance of the membrane-electrode-assembly(MEA)based on the polybenzimidazole(PBI)membrane in the HTPEMFC.The doping of 1.5 wt%GO synthesised by electrochemical exfoliation with the 2-step method or reactor method in PBI increased the peak power density by 17.4%or 35.4%compared to MEA based on pure PBI membrane at 150℃,respectively.In addition,the doping of PGO in PBI improves its durability under accelerated stress test(AST).展开更多
The adsorption dynamics of double-stranded DNA(dsDNA)molecules on a graphene oxide(GO)surface are important for applications of DNA/GO functional structures in biosensors,biomedicine and materials science.In this work...The adsorption dynamics of double-stranded DNA(dsDNA)molecules on a graphene oxide(GO)surface are important for applications of DNA/GO functional structures in biosensors,biomedicine and materials science.In this work,molecular dynamics simulations were used to examine the adsorption of different length dsDNA molecules(from 4 bp to24 bp)on the GO surface.The dsDNA molecules could be adsorbed on the GO surface through the terminal bases and stand on the GO surface.For short dsDNA(4 bp)molecules,the double-helix structure was partially or totally broken and the adsorption dynamics was affected by the structural fluctuation of short dsDNA and the distribution of the oxidized groups on the GO surface.For long dsDNA molecules(from 8 bp to 24 bp)adsorption is stable.By nonlinear fitting of the contact angle between the axis of the dsDNA molecule and the GO surface,we found that a dsDNA molecule adsorbed on a GO surface has the chance of orienting parallel to the GO surface if the length of the dsDNA molecule is longer than 54 bp.We attributed this behavior to the flexibility of dsDNA molecules.With increasing length,the flexibility of dsDNA molecules also increases,and this increasing flexibility gives an adsorbed dsDNA molecule more chance of reaching the GO surface with the free terminal.This work provides a whole picture of adsorption of dsDNA molecules on the GO surface and should be of benefit for the design of DNA/GO based biosensors.展开更多
The rational synthesis of a two-dimensional(2D)porous aromatic framework(PAF)with a controllable growth direction remains a challenge to overcome the limitation of traditional stacked 2D materials.Herein,a step-growth...The rational synthesis of a two-dimensional(2D)porous aromatic framework(PAF)with a controllable growth direction remains a challenge to overcome the limitation of traditional stacked 2D materials.Herein,a step-growth strategy is developed to fabricate a vertically oriented nitrogen-rich porous aromatic framework on graphene oxide(V-PAF-GO)using monolayer benzidine-functionalized GO(BZ-GO)as a molecular pillar.Then,the confined Co nanoparticle(NP)catalysts are synthesized by encapsulating ultra-small Co into the slit pores of V-PAF-GO.Due to the high nitrogen content,large specific surface area,and adequate slit pores,the optimized vertical nanocomposites V-PAF-GO provide abundant anchoring sites for metal NPs,leading to ultrafine Co NPs(1.4 nm).The resultant Co/V-PAF-GO catalyst shows an extraordinary catalytic activity for ammonia borane(AB)methanolysis,yielding a turnover frequency value of 47.6 min−1 at 25°C,comparable to the most effective non-noble-metal catalysts ever reported for AB methanolysis.Experimental and density functional theory studies demonstrate that the electron-donating effect of N species of PAF positively corresponds to the low barrier in methanol molecule activation,and the cleavage of the O–H bond in CH3OH has been proven to be the rate-determining step for AB methanolysis.This work presents a versatile step-growth strategy to prepare a vertically oriented PAF on GO to solve the stacking problem of 2D materials,which will be used to fabricate other novel 2D or 2D–2D materials with controllable orientation for various applications.展开更多
基金Project supported by the Central University Special Fund Basic Research and Operating Expenses,China(Grant No.GK201702005)the Natural Science Foundation of Shaanxi Province,China(Grant No.2017JM6091)+1 种基金the National Natural Science Foundation of China(Grant No.61705183)the Fundamental Research Funds for the Central Universities,China(Grant No.2017TS011)
文摘The carboxyl-functionalized graphene oxide(GO-COOH) is a kind of unique two-dimensional(2 D) material and possesses excellent nonlinear saturable absorption property and high water-solubility. In this paper, we prepare saturable absorber(SA) device by depositing GO-COOH nanosheets aqueous solution on a D-shaped fiber. The modulation depth(MD) and saturable intensity of the SA are measured to be 9.6% and 19 MW/cm^2, respectively. By inserting the SA into the erbium-doped fiber(EDF) laser, a passively mode-locked EDF laser has been achieved with the spectrum center wavelength of 1562.76 nm. The pulse duration, repetition rate, and the signal-to-noise ratio(SNR) are 500 fs, 14.79 MHz, and 80 dB,respectively. The maximum average output power is measured to be 3.85 mW. These results indicate that the GO-COOH nanosheets SA can be used as a promising mode locker for the generation of ultrashort pulses.
基金Funded by the National Key Research and Development(R&D) Program of China(No.2018YFB1105702)。
文摘A novel strategy was developed to prepare the methacrylic gelatin-dopamine(GelMA-DA)/Ag nanoparticles(NPs)/graphene oxide(GO) composite hydrogels with good biocompatibility,mechanical properties,and antibacterial activity.Mussel-inspired DA was utilized to modify the GelMA molecules,which imparts good adhesive performance to the hydrogels.GO,interfacial enhancer,not only improves mechanical properties of the hydrogels,but also provides anchor sites for loading Ag NPs through numerous oxygencontaining functional groups on the surface.The experimental results show that the GelMA/Ag NPs/GO hydrogels have good biocompatibility,and exhibit a swelling rate of 202±16%,the lap shear strength of 147±17 kPa,and compressive modulus of 136±53 kPa,in the case of the Ag NPs/GO content of 2 mg/mL.Antibacterial activity of the hydrogels against both gram-negative and gram-positive bacteria is dependent on the Ag NPs/GO content derived from the release of Ag^(+).Furthermore,the GelMA/Ag NPs/GO hydrogels possess good adhesive ability,which is resistant to highly twisted state when stuck on the surface of pigskin.These results demonstrate promising potential of the GelMA-DA/Ag NPs/GO hydrogels as wound dressings for biomedical applications in clinical and emergent treatment.
基金funded by the National Natural Science Foundation of China(No.51872137)and Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)。
文摘Graphene oxide(GO)as a new nano-enhancer in cement-based materials has gained wide attention.However,GO is easy to aggregate in alkaline cement mortar with poor dispersibility.This hinders its application in practical infrastructure construction.In this work,GO-M18 polycarboxylate compound superplasticizer(GM)were obtained by compounding the M18 polycarboxylate superplasticizer with GO solution at different mass ratios.The dispersion of GM in alkaline solution was systematically studied.The phases and functional groups of GM were characterized by XRD and FTIR.The effects of GM on the cement mortar hydration and the formation of microstructure were investigated by measuring the heat of hydration,MIP,TG/DSC,and SEM.The results show that the long-chain structure of the M18 polycarboxylate superplasticizer can increase the interlayer spacing of GO and weaken the force between GO sheets.The modified GO can be uniformly dispersed in the cement slurry.GM can accelerate the early hydration process of cement,which can increase the content of Ca(OH)2 and decrease the grain size.It can optimize the pore size distribution of cement-based materials,increase the density of harmless and less harmful pores,thereby improving mechanical properties.Such methods can transform traditional cement-based materials into stronger,more durable composites,which prolong the life of cement-based materials and reduce the amount of cement used for later maintenance.This provides an idea for achieving sustainability goals in civil engineering.
基金the financial support of the National Key R&D Program of China(No.2019YFC1806000)the Huazhong University of Science and Technology(No.3004013118)+2 种基金support from the National Natural Science Foundation of China(No.51903099)Huazhong University of Science and Technology(No.3004013134)the 100 Talents Program of the Hubei Provincial Government.Z.D.thanks the Postdoctoral Science Foundation of China(No.0106013063).
文摘Graphene oxide(GO)is regarded as a promising candidate to construct solar absorbers for addressing freshwater crisis,but the easy delamination of GO in water poses a critical challenge for practical solar desalination.Herein,we improve the stability of GO membranes by a self-crosslinking poly(ionic liquid)(PIL)in a mild condition,which crosslinks neighbouring GO nanosheets without blemishing the hydrophilic structure of GO.By further adding carbon nanotubes(CNTs),the sandwiched GO/CNT@PIL(GCP)membrane displays a good stability in pH=1 or 13 solution even for 270 days.The molecular dynamics simulation results indicate that the generation of water nanofluidics in nanochannels of GO nanosheets remarkably reduces the water evaporation enthalpy in GCP membrane,compared to bulk water.Consequently,the GCP membrane exhibits a high evaporation rate(1.87 kg m^(-2)h^(-1))and displays stable evaporation rates for 14 h under 1 kW m^(-2)irradiation.The GCP membrane additionally works very well when using different water sources(e.g.,dye-polluted water)or even strong acidic solution(pH=1)or basic solution(pH=13).More importantly,through bundling pluralities of GCP membrane,an efficient solar desalination device is developed to produce drinkable water from seawater.The average daily drinkable water amount in sunny day is 10.1 kg m^(-2),which meets with the daily drinkable water needs of five adults.The high evaporation rate,long-time durability and good scalability make the GCP membrane an outstanding candidate for practical solar seawater desalination.
基金supported by the China Postdoctoral Science Foundation(No.2021MD703944)the Fund of Science and Technology on Near-Surface Detection Laboratory(No.6142414211808)+1 种基金the Director Fund of State Key Laboratory of Pulsed Power Laser Technology(No.SKL2021ZR06)the National Natural Science Foundation of China(No.21776053)。
文摘Reduced graphene oxide(rGO)aerogels are emerging as very attractive scaffolds for high-performance electromagnetic wave absorption materials(EWAMs)due to their intrinsic conductive networks and intricate interior microstructure,as well as good compatibility with other electromagnetic(EM)components.Herein,we realized the decoration of rGO aerogel with Mo_(2)C nanoparticles by sequential hydrothermal assembly,freeze-drying,and high-temperature pyrolysis.Results show that Mo_(2)C nanoparticle loading can be easily controlled by the ammonium molybdate to glucose molar ratio.The hydrophobicity and thermal insulation of the rGO aerogel are effectively improved upon the introduction of Mo_(2)C nanoparticles,and more importantly,these nanoparticles regulate the EM properties of the rGO aerogel to a large extent.Although more Mo_(2)C nanoparticles may decrease the overall attenuation ability of the rGO aerogel,they bring much better impedance matching.At a molar ratio of 1:1,a desirable balance between attenuation ability and impedance matching is observed.In this context,the Mo_(2)C/r GO aerogel displays strong reflection loss and broad response bandwidth,even with a small applied thickness(1.7 mm)and low filler loading(9.0wt%).The positive effects of Mo_(2)C nanoparticles on multifunctional properties may render Mo_(2)C/r GO aerogels promising candidates for high-performance EWAMs under harsh conditions.
基金the support of the National Natural Science Foundation of China(51971146,51971147,52171218 and 52271222)the Shanghai Municipal Science and Technology Commission(21010503100 and 20ZR1438400)+3 种基金the Innovation Program of Shanghai Municipal EducationCommission(No.2019-01-07-00-07-E00015)the Shanghai Rising-Star Program(20QA1407100 and Yangfan Special Project:23YF1428900)the support of the Advanced Research and Technology Innovation Centre(ARTIC,Project Number ADT-RP2/A0005947-32-00)for research conducted by John Wang’s group。
文摘Promising room-temperature sodium-sulfur(RT Na-S)battery systems rely on purposely designed highperforming and low-cost electrode materials.Nevertheless,there are the challenges of irreversible dissolution and slow redox kinetics of NaPSs in the complete discharge of sulfur capacity.Herein,engineered CoMoO_(4)in reduced graphene oxide(CoMoO_(4)@rGO)is reported as a class of superior cathode hosts for RT Na-S batteries.The CoMoO_(4)@rGO matrix is designed to facilitate the reversible sodiation and desodiation of sulfur,considering the strong chemisorption between sulfur(and short-chain sodium sulfides)and CoMoO_(4),which alleviates the shuttle effect of sodium sulfides and accelerates the electrochemical reaction rate at RT.The obtained S/CoMoO_(4)@rGO cathode with~52%S loading exhibits a high capacity of520.1 mA h g^(-1)after 100 cycles at 0.1 A g^(-1).Moreover,an enhanced long-term performance at high current densities(212.2 mA h g^(-1)at 4 A g^(-1)over 1000 cycles)with high Coulombic efficiency(~100%)is also achieved.This work demonstrates a novel multifunctional additive for RT Na-S battery cathodes,which is expected to promote the long-waited development towards practical applications of RT Na-S batteries.
基金supported by the National Natural Science Foundation of China, No. 81871493 (to YC)the Medical Science Advancement Program (Clinical Medicine) of Wuhan University, No. TFLC2018003 (to YC)
文摘Currently available commercial nerve guidance conduits have been applied in the repair of peripheral nerve defects.However,a conduit exhibiting good biocompatibility remains to be developed.In this work,a series of chitosan/graphene oxide(GO)films with concentrations of GO varying from 0-1 wt%(collectively referred to as CHGF-n)were prepared by an electrodeposition technique.The effects of CHGF-n on proliferation and adhesion abilities of Schwann cells were evaluated.The results showed that Schwann cells exhibited elongated spindle shapes and upregulated expression of nerve regeneration-related factors such as Krox20(a key myelination factor),Zeb2(essential for Schwann cell differentiation,myelination,and nerve repair),and transforming growth factorβ(a cytokine with regenerative functions).In addition,a nerve guidance conduit with a GO content of 0.25%(CHGFC-0.25)was implanted to repair a 10-mm sciatic nerve defect in rats.The results indicated improvements in sciatic functional index,electrophysiology,and sciatic nerve and gastrocnemius muscle histology compared with the CHGFC-0 group,and similar outcomes to the autograft group.In conclusion,we provide a candidate method for the repair of peripheral nerve defects using free-standing chitosan/GO nerve conduits produced by electrodeposition.
基金the Ministry of Science and Technology of China(Grant Nos.2018YFA0305800 and2019YFA0308500)the National Natural Science Foundation of China(Grant No.61925111)+2 种基金the Chinese Academy of Sciences(Grant Nos.XDB28000000 and YSBR-003)the Fundamental Research Funds for the Central Universitiesthe CAS Key Laboratory of Vacuum Physics。
文摘Intercalation of insulating materials between epitaxial graphene and the metal substrates is highly demanded to restore the intrinsic properties of graphene,and thus essential for the graphene-based devices.Here we demonstrate a successful solution for the intercalation of hafnium oxide into the interface between full-layer graphene and Ir(111)substrate.We first intercalate hafnium atoms beneath the epitaxial graphene.The intercalation of the hafnium atoms leads to the variation of the graphene moire superstructure periodicity,which is characterized by low-energy electron diffraction(LEED)and lowtemperature scanning tunneling microscopy(LT-STM).Subsequently,we introduce oxygen into the interface,resulting in oxidization of the intercalated hafnium.STM and Raman's characterizations reveal that the intercalated hafnium oxide layer could effectively decouple the graphene from the metallic substrate,while the graphene maintains its high quality.Our work suggests a high-k dielectric layer has been successfully intercalated between high-quality epitaxial graphene and metal substrate,providing a platform for applications of large-scale,high-quality graphene for electronic devices.
基金supported by the National Natural Science Foundation of China(22078269 and 51708406).
文摘Graphene oxide(GO) channels exhibit unique mass transport behaviors due to their flexibility, controllable thinness and extraordinary physicochemical properties, enabling them to be widely used for adsorption and membrane separation. Nevertheless, the adsorption behavior of nanosized contaminants within the channels of GO membrane has not been fully discussed. In this study, we fabricated a GO membrane(PGn, where n represents the deposition cycles of GO) with multi channels via the crosslinking of GO and multibranched poly(ethyleneimine)(PEI). Phenol was used as molecular probe to determine the correlations between dynamic adsorption behavior and structural parameters of the multilevel GO/PEI membrane. PG8 shows higher adsorption capacities and affinity, which is predominantly attributed to the multichannel structure providing a large specific surface for phenol adsorption, enhancing the accessibility of active sites for phenol molecules and the transport of phenol. Density functional theory calculations demonstrate that the adsorption mechanism of phenol within GO channel is energetically oriented by hydrogen bonds, which is dominated by oxygen-containing groups compared to amino groups. Particularly, the interfaces which facilitate strong π-π interaction and hydrogen bonds maybe the most active regions. Moreover, the as-prepared PG8 membrane showed outstanding performance for other contaminants such as methyl orange and Cr(VI). It is anticipated that this study will have implications for design of GO-related environmental materials with enhanced efficiency.
基金supported by the Research and Development Institute at Nakhon Si Thammarat Rajabhat University and the Nanomaterials Chemistry Research Unit at Nakhon Si Thammarat Rajabhat University,Nakhon Si Thammarat,Thailand(Grant No.004/2563).
文摘In this paper, we present a proof-of-concept study of the enhancement of photocatalytic activity via a combined strategy of fabricating a visible-light responsive ternary heterostructure and improving overall photostability by incorporating magnetic zinc oxide/graphene/iron oxide (ZGF). A solvothermal approach was used to synthesize the catalyst. X-ray diffraction (XRD), scanning electron microscopic, energy dispersive X-ray, transmission electron microscopic, vibrating sample magnetometric, and ultraviolet–visible diffuse reflectance spectroscopic techniques were used to characterize the synthesized samples. The obtained optimal Zn(NO_(3))_(2) concentration, temperature, and heating duration were 0.10 mol/L, 600℃, and 1 h, respectively. The XRD pattern revealed the presence of peaks corresponding to zinc oxide, graphene, and iron oxide, indicating that the ZGF catalyst was effectively synthesized. Furthermore, when the developed ZGF was used for methylene blue dye degradation, the optimum irradiation time, dye concentration, catalyst dosage, irradiation intensity, and solution pH were 90 min, 10 mg/L, 0.03 g/L, 100 W, and 8.0, respectively. Therefore, the synthesized ZGF system could be used as a catalyst to degrade dyes in wastewater samples. This hybrid nanocomposite consisting of zinc oxide, graphene, and iron oxide could also be used as an effective photocatalytic degrader for various dye pollutants.
基金grateful for funding from the National Natural Science Foundation of China(Grant No.52174053,52130401 and 51974344)Natural Science Foundation of Shandong Provincial(ZR2019MEE077).
文摘Asymmetrically modified Janus graphene oxide(JGO)has attracted great attention due to its unique physical chemistry properties and wide applications.The modification degree of Janus nanosheets inevitably affects their interfacial activity,which is essential for their performances in enhanced oil recovery(EOR).In this study,the interfacial properties of Janus graphene oxide(JGO)with various modification degrees at liquid-liquid and liquid-solid interfaces were systematically evaluated via the measurements of interfacial tension(IFT),dilatational modulus,contact angle,and EOR efficiency was further assessed by core flooding tests.It is found that JGO-5 with higher modification degree exhibits the greater ability to reduce IFT(15.16 mN/m)and dilatational modulus(26 mN/m).Furthermore,JGO can construct interfacial and climbing film with the assistance of hydrodynamic power to effectively detach the oil from the rock surface and greatly enhance oil recovery.Moderately modified JGO-2 can highly improve recovery of residual crude oil(11.53%),which is regarded as the promising EOR agent in practical application.The present study firstly focuses on the effects of modification degrees on the JGO interfacial properties and proposes diverse EOR mechanisms for JGO with different modification degrees.
文摘This paper investigates the effects of pH on stability and thermal properties of copper oxide(CuO),graphene oxide(GO),and their hybrid nanofluid(HNF)at different mixing ratios.Initially,sol-gel and Hummer’s method was employed for the synthesis of CuO and GO nanoparticles(NPs),and they are characterized with various techniques.The effects of two different surfactants were analyzed on nanofluid’s(NF’s)stability at different pH values.The properties like thermal conductivity(TC)and viscosity(VST)of NFs were measured at different volume concentration(0.1 vol%to 1.0 vol%)and temperature range of 30-60℃,respectively.The TC and VST of GO/CuO(50:50)HNF are higher than that of GO/CuO(20:80).The figure of merit(FOM)is determined for the studied HNFs.The correlations were presented to calculate the TC as well as VST of HNFs.Two modern novel machine learning-based ensemble approaches were employed for predictive model development for TC and VST of considered HNFs.The comparison of prognostic models with Taylor’s diagram revealed that Bayesian optimized support vector machine(BoASVM)was superior to Bayesian optimized boosted regression trees(BoA-BRT)for both TC and VST models.
文摘In the present study, polyethersulfone based nanohybrid membranes were effectively fabricated by incorporating graphene oxide(GO) and hydrotalcite(HT) nanosheets into the membrane structure. HT was prepared to overcome the irreversible agglomeration behavior of GO at a high concentration which affects the performance of the membranes. In particular, the shedding of HT in formamide provides a two-dimensional nanosheet with a higher positive charge density to prevent the restacking of GO nanosheets. Here, exfoliated GO and HT with different combinations(1:1, 1:2 and 1:3) were infused in the membrane matrix to treat lead-acid battery effluent effectively. Finally, the hybrid membranes were characterized for hydrophilicity, mechanical strength and pure water flux. In combination with the superior properties of GO and HT, the prepared hybrid membranes can be used as effectively to improve the separation and permeation performance. The phase inversion process eliminated the leaching of nanoparticles from the membrane matrix. The reusability of the hybrid membrane was achieved using0.1 mol·L^(-1)NaOH solution and reused without significant reduction in lead removal efficiency. The cost analysis of the membrane was also estimated from the lab study. Therefore, the present study suggested the selective and sustainable treatment of lead from a real-life effluent.
基金financially supported by the National Natural Science Foundation of China(52077207 and 51907193)the Key Research Program of Frontier Sciences,CAS(ZDBS-LY-JSC047)the Youth Innovation Promotion Association CAS(2020145)。
文摘Practical applications of diverse flexible wearable electronics require electrochemical energy storage(EES)devices with multiple configurations.Moreover,to fabricate flexible EES devices with high energy density and stability,organic integration from electrode design to device assembly is required.To address these challenges,a free-standing reduced graphene oxide(rGO)/carbon film with a unique sandwich structure has been designed via the assistance of vacuum-assistant filtration for lithium-ion capacitors(LICs).The graphene acts as not only a binder to construct a three-dimensional conductive network but also an active material to provide additional capacitive lithium storage sites,thus enabling fast ion/electron transport and improving the capacity.The designed rGO/hard carbon(rGO/HC)and rGO/activated carbon(rGO/AC)free-standing films exhibit enhanced specific capacities(513.7 mA h g^(-1)for rGO/HC and 102.8 mA h g^(-1)for rGO/AC)and excellent stability.Moreover,the integrated flexible quasi-solid-state rGO/AC//rGO/HC LIC devices possess a maximum energy density of 138.3 Wh kg^(-1),a high power density of 11 kW kg^(-1),and improved cycling performance(84.4%capacitance maintained after 10,000 cycles),superior to the AC//HC LIC(43.5%retention).Such a strategy enlightens the development of portable flexible LICs.
基金supported by the National Natural Science Foundation of China(51902007)。
文摘Water pollution regarding dyes and heavy metal ions is crucial facing the world.How to effectively separate these contaminants from water has been a key issue.Graphene oxide(GO)promises the greenwater world as a long-lasting spotlight adsorbent material and therefore,harnessing GO has been the research hotspot for over a decade.The state of GO as well as its surface functional groups plays an important role in adsorption.And the way of preparation and structural modification matters to the performance of GO.In this review,the significance of the state of existence of stock GO and surface functional groups is explored in terms of preparation,structural modification,and adsorption.Besides,various adsorbates for GO adsorption are also involved,the discussion of which is rarely established elsewhere.
基金Ho Chi Minh City University of Technology (HCMUT),VNU-HCM for supporting this study。
文摘In this study,three-dimensional porous magnesium ferrite/titanium dioxide/reduced graphene oxide(Mg Fe_2O_(4)-GM/TiO_(2)/rGO(MGTG))was successfully synthesized via green and hydrothermal-supported co-precipitation methods using the extract of Garcinia mangostana(G.mangostana)as a reducing agent.The characterization results indicate the successful formation of the nano/micro Mg Fe_(2)O_(4)(MFO)and TiO_(2) on the structure of the reduced graphene oxide(rGO),which can also act as efficient support,alleviating the agglomeration of the nano/micro MFO and TiO_(2).The synergic effects of the adsorption and photodegradation activity of the material were investigated according to the removal of crystal violet(CV)under ultraviolet light.The effects of catalyst dosage,CV concentration,and p H on the CV removal efficiency of the MGTG were also investigated.According to the results,the CV photodegradation of the MGTG-200 corresponded to the pseudo-first-order kinetic model.The reusability of the material after 10 cycles also showed a removal efficiency of 92%.This happened because the materials can easily be recollected using external magnets.In addition,according to the effects of different free radicals·O_(2)^(-),h^(+),and·OH on the photodegradation process,the photocatalysis mechanism of the MGTG was also thoroughly suggested.The antibacterial efficiency of the MGTG was also evaluated according to the inhibition of the Gram-positive bacteria strain Staphylococcus aureus(S.aureus).Concurrently,the antibacterial mechanism of the fabricated material was also proposed.These results confirm that the prepared material can be potentially employed in a wide range of applications,including wastewater treatment and antibacterial activity.
基金supported by the National Key Research and Development Project (Grant No. 2018YFE0124800)the National Key Research Program of China (Grant No.2022YFA1503100)+7 种基金Science and Technology Project of Jiangsu Province (Grant No. BZ2020011)National Natural Science Foundation of China (Grants No. 22173067)the Science and Technology Development FundMacao SAR(FDCT No. 0052/2021/A)Collaborative Innovation Center of Suzhou Nano Science&Technologythe Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD)the 111 ProjectJoint International Research Laboratory of Carbon-Based Functional Materials and Devices
文摘Lithium-sulfur(Li-S) batteries can provide far higher energy density than currently commercialized lithium ion batteries, but challenges remain before it they are used in practice.One of the challenges is the shuttle effect that originates from soluble intermediates, like lithium polysulfides. To address this issue, we report a novel laminar composite, N,O-carboxymethyl chitosan-reduced graphene oxide(CC-rGO), which is manufactured via the self-assembly of CC onto GO and subsequent reduction of GO under an extreme condition of 1 Pa and-50°C. The synthesized laminar CC-rGO composite is mixed with acetylene black(AB) and coated on a commercial polypropylene(PP) membrane, resulting in a separator(CC-rGO/AB/PP) that can not only completely suppress the polysulfides penetration, but also can accelerate the lithium ion transportation, providing a Li-S battery with excellent cyclic stability and rate capability. As confirmed by theoretic simulations, this unique feature of CC-rGO is attributed to its strong repulsive interaction to polysulfide anions and its benefit for fast lithium ion transportation through the paths paved by the heteroatoms in CC.
基金financially supported by the UK Research Council EPSRC EP/009050/1。
文摘The doping of functionalized graphene oxide(GO)in the membranes becomes a promising method for improving the performance of high-temperature proton exchange membrane fuel cells(HT-PEMFC).Phosphonated graphene oxide(PGO)with a P/O ratio of 8.5%was quickly synthesised by one-step electrochemical exfoliation based on a three-dimensiaonal(3D)printed reactor and natural graphite flakes.Compared with the GO prepared by the two-step electrochemical exfoliation method,the PGO synthesized by the one-step electrochemical exfoliation can better improve the performance of the membrane-electrode-assembly(MEA)based on the polybenzimidazole(PBI)membrane in the HTPEMFC.The doping of 1.5 wt%GO synthesised by electrochemical exfoliation with the 2-step method or reactor method in PBI increased the peak power density by 17.4%or 35.4%compared to MEA based on pure PBI membrane at 150℃,respectively.In addition,the doping of PGO in PBI improves its durability under accelerated stress test(AST).
基金Project supported by the National Natural Science Foundation of China (Grant No.11974366)the Fundamental Research Funds for the Central Universities+2 种基金Chinathe Supercomputer Center of the Chinese Academy of Sciencesthe Shanghai Supercomputer Center of China。
文摘The adsorption dynamics of double-stranded DNA(dsDNA)molecules on a graphene oxide(GO)surface are important for applications of DNA/GO functional structures in biosensors,biomedicine and materials science.In this work,molecular dynamics simulations were used to examine the adsorption of different length dsDNA molecules(from 4 bp to24 bp)on the GO surface.The dsDNA molecules could be adsorbed on the GO surface through the terminal bases and stand on the GO surface.For short dsDNA(4 bp)molecules,the double-helix structure was partially or totally broken and the adsorption dynamics was affected by the structural fluctuation of short dsDNA and the distribution of the oxidized groups on the GO surface.For long dsDNA molecules(from 8 bp to 24 bp)adsorption is stable.By nonlinear fitting of the contact angle between the axis of the dsDNA molecule and the GO surface,we found that a dsDNA molecule adsorbed on a GO surface has the chance of orienting parallel to the GO surface if the length of the dsDNA molecule is longer than 54 bp.We attributed this behavior to the flexibility of dsDNA molecules.With increasing length,the flexibility of dsDNA molecules also increases,and this increasing flexibility gives an adsorbed dsDNA molecule more chance of reaching the GO surface with the free terminal.This work provides a whole picture of adsorption of dsDNA molecules on the GO surface and should be of benefit for the design of DNA/GO based biosensors.
基金National Natural Science Foundation of China,Grant/Award Number:22162014 and 22162013Natural Science Foundation of Jiangxi Province of China,Grant/Award Number:20212ACB204009+1 种基金Sponsored Program for Academic and Technical Leaders of Major Disciplines of Jiangxi Province of China,Grant/Award Number:20212BCJL23059Doctoral Research Foundation Project of Tongren University,Grant/Award Number:trxyDH2204。
文摘The rational synthesis of a two-dimensional(2D)porous aromatic framework(PAF)with a controllable growth direction remains a challenge to overcome the limitation of traditional stacked 2D materials.Herein,a step-growth strategy is developed to fabricate a vertically oriented nitrogen-rich porous aromatic framework on graphene oxide(V-PAF-GO)using monolayer benzidine-functionalized GO(BZ-GO)as a molecular pillar.Then,the confined Co nanoparticle(NP)catalysts are synthesized by encapsulating ultra-small Co into the slit pores of V-PAF-GO.Due to the high nitrogen content,large specific surface area,and adequate slit pores,the optimized vertical nanocomposites V-PAF-GO provide abundant anchoring sites for metal NPs,leading to ultrafine Co NPs(1.4 nm).The resultant Co/V-PAF-GO catalyst shows an extraordinary catalytic activity for ammonia borane(AB)methanolysis,yielding a turnover frequency value of 47.6 min−1 at 25°C,comparable to the most effective non-noble-metal catalysts ever reported for AB methanolysis.Experimental and density functional theory studies demonstrate that the electron-donating effect of N species of PAF positively corresponds to the low barrier in methanol molecule activation,and the cleavage of the O–H bond in CH3OH has been proven to be the rate-determining step for AB methanolysis.This work presents a versatile step-growth strategy to prepare a vertically oriented PAF on GO to solve the stacking problem of 2D materials,which will be used to fabricate other novel 2D or 2D–2D materials with controllable orientation for various applications.
