The microstructure and mechanical properties of Mg-10.1Gd-3.74Y-0.25Zr （mass fraction, %） alloy （GW104 alloy） cast by metal mould casting （MMC） and lost foam casting （LFC） were evaluated, respectively. It is r...The microstructure and mechanical properties of Mg-10.1Gd-3.74Y-0.25Zr （mass fraction, %） alloy （GW104 alloy） cast by metal mould casting （MMC） and lost foam casting （LFC） were evaluated, respectively. It is revealed that different forming modes do not influence the phase composition of as-cast alloy. In the as-cast specimens, the microstructures are similar and composed of α-Mg solid solution, eutectic compound of α-Mg＋Mg 24 （Gd, Y） 5 and cuboid-shaped Mg 5 （Gd, Y） phase; whereas the average grain size of the alloy produced by metal mould casting is smaller than that by lost foam casting. The eutectic compound of the alloy is completely dissolved after solution treatment at 525 ℃for 6 h, while the Mg 5 （Gd, Y） phase still exists after solution treatment. After peak-ageing, the lost foam cast alloy exhibits the maximum ultimate tensile strength of 285 MPa, and metal mould cast specimen 325 MPa at room temperature, while the tensile yield strengths of them are comparable. It can be concluded that GW104 alloy cast by lost foam casting possesses similar microstructure and evidently lower mechanical strength compared with metal mould cast alloy, due to slow solidification rate and proneness to form shrinkage porosities during lost foam casting process.展开更多
The present work investigated the solidification microstructure of AISI M2 high speed steel manufactured by different casting technologies, namely iron mould casting and continuous casting. The results revealed that t...The present work investigated the solidification microstructure of AISI M2 high speed steel manufactured by different casting technologies, namely iron mould casting and continuous casting. The results revealed that the as-cast structure of the steel was composed of the iron matrix and the M2C eutectic carbide networks, which were greatly refined in the ingot made by continuous casting process, compared with that by the iron mould casting process. M2C eutectic carbides presented variation in their morphologies and growth characteristics in the ingots by both casting methods. In the ingot by iron mould casting, they have a plate-like morphology and grow anisotropically. However, in the ingot made by continuous casting, the carbides evolved into the fiber-like shape that exhibited little characteristics of anisotropic growth. It was noticed that the fiber-like M2C was much easier to decompose and spheroidize after heated, as a result, the carbides refined remarkably, compared with the case of plate-like carbides in the iron mould casting ingot.展开更多
The microstructure and hydrogen storage properties of low V content （Ti0.46Cr0.54）100-xVx （x = 2.5-7.1, at%） and （TiyCr1-y）95V5 （y= 0.38-0.54） alloys were investigated. These alloys were prepared by arc meltin...The microstructure and hydrogen storage properties of low V content （Ti0.46Cr0.54）100-xVx （x = 2.5-7.1, at%） and （TiyCr1-y）95V5 （y= 0.38-0.54） alloys were investigated. These alloys were prepared by arc melting and copper mould suction casting. The structures of as-cast （Ti0.46Cr0.54）100-xVx （x = 2.5, 5.0, and 7.1） alloy ingots evolve with V contents from pure Laves-（x = 2.5） to dual-phase TiCr2-BCC structures （5.0 and 7.1）, whereas the suction-cast （Ti0.46Cr0.54）100-xVx （x =2.5, 5.0, and 7.1） alloys only contain single BCC phase. The suction-cast alloy rod （Ti0.46Cr0.54）95V5, containing only 5.0 at% V is shown to possess the optimum hydrogen absorption capacity, with the maximum hydrogen content of 3.14 wt%. Furthermore, the hydrogen storage properties of the suction-cast low V alloys （TiyCr1-y）95V5 （y = 0.38-0.54） are sensitive to Ti/Cr ratios and only those alloys with Ti/Cr ratios close to the CN14 cluster [TiTCrs] have good hydrogen storage properties.展开更多
The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhan...The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhances the meniscus oscillation, thus increases the probability of slag entrapment, and the critical argon blowing flow rate, which will give rise to slag entrapment, is around 10l/min. The trajectory of bubble is affected by the bubble diameter and the molten steel flow, and the bubble diameter is dominant. The bubble with diameter 1.4mm floats fastest with 0.47m/s terminal velocity.展开更多
Although the shell mould casting process has a wide range of application in many fields,the prediction of casting defects is still a problem.In the present work,a typical leaf spring bracket casting of ZG310-570 was f...Although the shell mould casting process has a wide range of application in many fields,the prediction of casting defects is still a problem.In the present work,a typical leaf spring bracket casting of ZG310-570 was fabricated by shell mold casting.The finite element model and ProCAST software were utilized for simulating the filling and solidification processes of the casting;and the formation mechanism of the gas pore,and shrinkage porosity defects were analyzed.The results indicate that the gas pore and shrinkage porosity defects are formed due to air entrapment,insufficient feeding and non-sequential solidification.Subsequently,through changing the position of risers,adding a connecting channel between the risers,and setting blind risers at the U-shaped brackets,an optimized gating and feeding system was established to improve the quality of the casting.After optimization,the gas pore and shrinkage porosity defects of the leaf spring bracket casting are effectively eliminated.The experiment results with the optimized casting process are in good agreement with the numerical simulation,which verifies the validity of the finite element model in the shell mould casting.展开更多
An integration system was developed to satisfy the need of information integration in the process of designing, investment casting and monitoring aero-engine's turbo blade. The general architecture is detailed pre...An integration system was developed to satisfy the need of information integration in the process of designing, investment casting and monitoring aero-engine's turbo blade. The general architecture is detailed presented in this paper. The system mainly comprises of product master model, design information management, anti-deformation design of mould cavity, intelligence mould design and blade testing. The developed system can manage mould design and blade test data flow, optimize mould design process and achieve the goal of integration design.展开更多
The relationships between the surface quality of a single crystal copper ingot and the process parameters of heated mould continuous casting method were studied experimentally using our own design of horizontal heated...The relationships between the surface quality of a single crystal copper ingot and the process parameters of heated mould continuous casting method were studied experimentally using our own design of horizontal heated mould continuous casting apparatus, and the mechanism by which process parameters affect the surface quality of a single crystal copper ingot is analyzed in the present paper. The results show that the process parameters affect the surface quality of a pure copper ingot by affecting the position of the liquid-solid interface in the mould. The position of the liquid-solid interface in the mould must be controlled carefully within an appropriate range, which is determined through a series of experiments, in order to gain a single crystal copper ingot with good surface quality.展开更多
The effect of process parameters on the surface quality of single crystal copper ingot was studied through experiment with a self-designed horizontal heated mould continuous casting apparatus,and the mechanism was ana...The effect of process parameters on the surface quality of single crystal copper ingot was studied through experiment with a self-designed horizontal heated mould continuous casting apparatus,and the mechanism was analyzed.The results show that the process parameters affect the surface quality of pure copper ingot by affecting the position of the liquid-solid interface in the mould.The position of the liquid-solid interface in the mould must be controlled carefully in an appropriate range determined through experiments in order to gain a single crystal copper ingot with a high surface quality.展开更多
Two ingots were produced by centrifugal casting at mould rotational speeds of 600 rpm and 800 rpm using 20 vol%SiC p /AlSi9Mg composite melt,respectively.The microstructure along the radial direction of cross-sectiona...Two ingots were produced by centrifugal casting at mould rotational speeds of 600 rpm and 800 rpm using 20 vol%SiC p /AlSi9Mg composite melt,respectively.The microstructure along the radial direction of cross-sectional sample of ingots was presented.SiC particles migrated towards the external circumference of the tube,and the distribution of SiC particles became uniform under centrifugal force.Voids in 20 vol%SiC p /AlSi9Mg composite melt migrated towards the inner circumference of the tube.The quantitative analysis results indicated that not only SiC particles but also primaryαphases segregated greatly in centrifugal casting resulting from the transportation behavior of constitutions with different densities in the SiC p /AlSi9Mg composite melt.In addition,the eutectic Si was broken owing to the motion of SiC p /AlSi9Mg composite melt during centrifugal casting.展开更多
The microstructures and crystal growth directions of permanent mould casting（PMC） and directionally solidified（DS） Al-Cu alloys with different contents of Cu were investigated. Simultaneously, the effects of pouri...The microstructures and crystal growth directions of permanent mould casting（PMC） and directionally solidified（DS） Al-Cu alloys with different contents of Cu were investigated. Simultaneously, the effects of pouring temperature on the microstructure and crystal growth direction of permanent mould casting pure Al were also discussed. The results indicate that the α（Al） crystals in the pure Al do not always keep common columnar grains, but change from the columnar grains to columnar dendrites with developed arms as the pouring temperature rises. The growth direction also varies with the change of pouring temperature. Cu element has similar effects on the microstructures of the PMC and DS casting Al-Cu alloys and the α（Al） crystals gradually change from columnar crystals in turn to columnar dendrites and developed equiaxed dendrites as the Cu content increases. The crystal growth direction in the PMC alloys gradually approaches （110） orientation with increasing Cu content. But the resulting crystals with growth direction of （110） do not belong to feathery grains. There are also no feathery grains to form in all of the DS Al-Cu alloys.展开更多
The microstructures and crystal growth directions of permanent mould casting and directionally solidified Al-Mg al oys with different Mg contents have been investigated. The results indicate that the effect of Mg cont...The microstructures and crystal growth directions of permanent mould casting and directionally solidified Al-Mg al oys with different Mg contents have been investigated. The results indicate that the effect of Mg content on microstructure is basical y same for the al oys prepared by these two methods. The primary grains change from cel ular crystals to developed columnar dendrites, and then to equiaxed dendrites as the Mg content is increased. Simultaneously, both the cel ular or columnar grain region and the primary trunk spacing decrease. Al of these changes are mainly attributed to the constitutional supercooling resulting from Mg element. Comparatively, the cellular or columnar crystals of the directionally solidified alloys are straighter and more paral el than those of the permanent mould casting al oys. These have straight or wavy grain boundaries, one of the most important microstructure characteristics of feathery grains. However, the transverse microstructure and growth direction reveal that they do not belong to feathery grains. The Mg seemingly can affect the crystal growth direction, but does not result in the formation of feathery grains under the conditions employed in the study.展开更多
Model study is an efficient method for optimizing the siructure of the mould and the submerged entry nozzle (SEN). Based on the similarity criteria, a full-scale water model has been established in accordance with the...Model study is an efficient method for optimizing the siructure of the mould and the submerged entry nozzle (SEN). Based on the similarity criteria, a full-scale water model has been established in accordance with the mould of thin-slab caster of the CSP (Compact Strip Production) operation. The effects of SEN structure including outlet area, outflow angle, nozzle width, thick-ness and immersion depth have been studied under high speed casting by measuring the amplitude and the impetus of top waves. By the orthogonal experiment design, not only the influence of the faCtors was estimated, but also the optimum work condition was judged. The rules of the fluid flow phenomena were summarized. The principle for choosing a reasonable structure of SEN was discussed.展开更多
Lubrication and friction between the mould and strand are strongly influenced by mould oscillation, and play an important role in slab quality and operating safety during continuous casting processes. Investigation of...Lubrication and friction between the mould and strand are strongly influenced by mould oscillation, and play an important role in slab quality and operating safety during continuous casting processes. Investigation of mould oscillation is therefore essential for getting a better online control of the mould processes. A feasible approach for the development and optimization of mould oscillation was put forward, which combined online measurement of mould friction, design of negative oscillating parameters and evaluation for powder consumption. Three different control models including sinusoidal and non-sinusoidal oscillation for mould oscillations were developed to investigate and evaluate the effects of oscillation on mould friction and powder lubrication. For the purpose of investigating mould friction between mould and strand, online measurement was carried out on a slab continuous caster equipped with a hydraulic oscillator. Also the comparison of the mould friction in sinusoidal and non-sinusoidal mould oscillation was made for subsequent analysis. The industrial experiment result shows that the combination of inverse control model and non-sinusoidal oscillation mode will contribute to the proper powder consumption, leading to a suitable effect of friction force on strand surface, especially for high speed continuous casting. The proposed method provides reliable basis for guiding and optimizing mould oscillation among control models, sinusoidal oscillation and non-sinusoidal oscillation.展开更多
The formation and propagation of the popular off-corner subsurface cracks in bloom continuous casting were investigated through thermo-mechanical analysis using three coupled thermo-mechanical models. A two-dimensiona...The formation and propagation of the popular off-corner subsurface cracks in bloom continuous casting were investigated through thermo-mechanical analysis using three coupled thermo-mechanical models. A two-dimensional thermo-elasto-visco-plastic finite element model was developed to predict the mould gap evolution, temperature profiles and deformation behavior of the solidified shell in the mould region. Then, a three-dimensional model was adopted to calculate the shell growth, tempera- ture history and the development of stresses and strains of the shell in the following secondary cooling zones. Finally, another three-dimensional model was used to analyze the stress distributions in the straightening region, The results showed that the off-corner cracks in the shell originated from the mould owing to the tensile strain developed in the crack sensitive regions of the solidification front, and they could be driven deeper by the possible severe surface temperature rebound and the extensive tensile stress in the secondary cooling zone, especially upon the straightening operation of the bloom casting. It is revealed that more homogenous shell temperature and thickness can be obtained through optimization of mould corner radius, casting speed and secondary cooling scheme, which help to decrease stress and strain concentration and therefore prevent the initiation of the cracks.展开更多
Immersion of automotive parts in a fluidized bed of foundry sand is used to both strip the castings free from moulding sand and to heat-treat the castings at 500℃. The fluid bed is heated by hot gases from a burner d...Immersion of automotive parts in a fluidized bed of foundry sand is used to both strip the castings free from moulding sand and to heat-treat the castings at 500℃. The fluid bed is heated by hot gases from a burner directed first into a serpentine heat exchanger located near one side-wall of the rectangular tank, and then into a distributor consisting of horizontal sparger pipes having maintenance standpipes fixed into their upper surfaces.展开更多
基金Project(2007CB613704)supported by the National Basic Research Program of China
文摘The microstructure and mechanical properties of Mg-10.1Gd-3.74Y-0.25Zr （mass fraction, %） alloy （GW104 alloy） cast by metal mould casting （MMC） and lost foam casting （LFC） were evaluated, respectively. It is revealed that different forming modes do not influence the phase composition of as-cast alloy. In the as-cast specimens, the microstructures are similar and composed of α-Mg solid solution, eutectic compound of α-Mg＋Mg 24 （Gd, Y） 5 and cuboid-shaped Mg 5 （Gd, Y） phase; whereas the average grain size of the alloy produced by metal mould casting is smaller than that by lost foam casting. The eutectic compound of the alloy is completely dissolved after solution treatment at 525 ℃for 6 h, while the Mg 5 （Gd, Y） phase still exists after solution treatment. After peak-ageing, the lost foam cast alloy exhibits the maximum ultimate tensile strength of 285 MPa, and metal mould cast specimen 325 MPa at room temperature, while the tensile yield strengths of them are comparable. It can be concluded that GW104 alloy cast by lost foam casting possesses similar microstructure and evidently lower mechanical strength compared with metal mould cast alloy, due to slow solidification rate and proneness to form shrinkage porosities during lost foam casting process.
基金supported by the Fund Project for Transformation of Scientific and Technological Achievements of Jiangsu Province,China(No.BA2010139)
文摘The present work investigated the solidification microstructure of AISI M2 high speed steel manufactured by different casting technologies, namely iron mould casting and continuous casting. The results revealed that the as-cast structure of the steel was composed of the iron matrix and the M2C eutectic carbide networks, which were greatly refined in the ingot made by continuous casting process, compared with that by the iron mould casting process. M2C eutectic carbides presented variation in their morphologies and growth characteristics in the ingots by both casting methods. In the ingot by iron mould casting, they have a plate-like morphology and grow anisotropically. However, in the ingot made by continuous casting, the carbides evolved into the fiber-like shape that exhibited little characteristics of anisotropic growth. It was noticed that the fiber-like M2C was much easier to decompose and spheroidize after heated, as a result, the carbides refined remarkably, compared with the case of plate-like carbides in the iron mould casting ingot.
基金financially supported by the National Natural Science Foundation of China(Nos.51171035 and 11174044)
文摘The microstructure and hydrogen storage properties of low V content （Ti0.46Cr0.54）100-xVx （x = 2.5-7.1, at%） and （TiyCr1-y）95V5 （y= 0.38-0.54） alloys were investigated. These alloys were prepared by arc melting and copper mould suction casting. The structures of as-cast （Ti0.46Cr0.54）100-xVx （x = 2.5, 5.0, and 7.1） alloy ingots evolve with V contents from pure Laves-（x = 2.5） to dual-phase TiCr2-BCC structures （5.0 and 7.1）, whereas the suction-cast （Ti0.46Cr0.54）100-xVx （x =2.5, 5.0, and 7.1） alloys only contain single BCC phase. The suction-cast alloy rod （Ti0.46Cr0.54）95V5, containing only 5.0 at% V is shown to possess the optimum hydrogen absorption capacity, with the maximum hydrogen content of 3.14 wt%. Furthermore, the hydrogen storage properties of the suction-cast low V alloys （TiyCr1-y）95V5 （y = 0.38-0.54） are sensitive to Ti/Cr ratios and only those alloys with Ti/Cr ratios close to the CN14 cluster [TiTCrs] have good hydrogen storage properties.
文摘The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhances the meniscus oscillation, thus increases the probability of slag entrapment, and the critical argon blowing flow rate, which will give rise to slag entrapment, is around 10l/min. The trajectory of bubble is affected by the bubble diameter and the molten steel flow, and the bubble diameter is dominant. The bubble with diameter 1.4mm floats fastest with 0.47m/s terminal velocity.
基金financially supported by the Major Science and Technology Projects in Anhui Province (No. 18030901097)the Natural Science Foundation of Anhui Province (No.1908085QE197)the Fundamental Research Funds for the Central Universities (JZ2018HGBZ0133, JZ2019HGTA0043)
文摘Although the shell mould casting process has a wide range of application in many fields,the prediction of casting defects is still a problem.In the present work,a typical leaf spring bracket casting of ZG310-570 was fabricated by shell mold casting.The finite element model and ProCAST software were utilized for simulating the filling and solidification processes of the casting;and the formation mechanism of the gas pore,and shrinkage porosity defects were analyzed.The results indicate that the gas pore and shrinkage porosity defects are formed due to air entrapment,insufficient feeding and non-sequential solidification.Subsequently,through changing the position of risers,adding a connecting channel between the risers,and setting blind risers at the U-shaped brackets,an optimized gating and feeding system was established to improve the quality of the casting.After optimization,the gas pore and shrinkage porosity defects of the leaf spring bracket casting are effectively eliminated.The experiment results with the optimized casting process are in good agreement with the numerical simulation,which verifies the validity of the finite element model in the shell mould casting.
基金National High-tech R&D Program (863 Program) (2006AA04Z144)Key Technologies R&D Program (2006BAF04B02).
文摘An integration system was developed to satisfy the need of information integration in the process of designing, investment casting and monitoring aero-engine's turbo blade. The general architecture is detailed presented in this paper. The system mainly comprises of product master model, design information management, anti-deformation design of mould cavity, intelligence mould design and blade testing. The developed system can manage mould design and blade test data flow, optimize mould design process and achieve the goal of integration design.
文摘The relationships between the surface quality of a single crystal copper ingot and the process parameters of heated mould continuous casting method were studied experimentally using our own design of horizontal heated mould continuous casting apparatus, and the mechanism by which process parameters affect the surface quality of a single crystal copper ingot is analyzed in the present paper. The results show that the process parameters affect the surface quality of a pure copper ingot by affecting the position of the liquid-solid interface in the mould. The position of the liquid-solid interface in the mould must be controlled carefully within an appropriate range, which is determined through a series of experiments, in order to gain a single crystal copper ingot with good surface quality.
文摘The effect of process parameters on the surface quality of single crystal copper ingot was studied through experiment with a self-designed horizontal heated mould continuous casting apparatus,and the mechanism was analyzed.The results show that the process parameters affect the surface quality of pure copper ingot by affecting the position of the liquid-solid interface in the mould.The position of the liquid-solid interface in the mould must be controlled carefully in an appropriate range determined through experiments in order to gain a single crystal copper ingot with a high surface quality.
基金Funded by Natural Science Foundation Project of CQ CSTC(No.2008BB4177)
文摘Two ingots were produced by centrifugal casting at mould rotational speeds of 600 rpm and 800 rpm using 20 vol%SiC p /AlSi9Mg composite melt,respectively.The microstructure along the radial direction of cross-sectional sample of ingots was presented.SiC particles migrated towards the external circumference of the tube,and the distribution of SiC particles became uniform under centrifugal force.Voids in 20 vol%SiC p /AlSi9Mg composite melt migrated towards the inner circumference of the tube.The quantitative analysis results indicated that not only SiC particles but also primaryαphases segregated greatly in centrifugal casting resulting from the transportation behavior of constitutions with different densities in the SiC p /AlSi9Mg composite melt.In addition,the eutectic Si was broken owing to the motion of SiC p /AlSi9Mg composite melt during centrifugal casting.
基金Project(51061010)supported by the National Natural Science Foundation of ChinaProject(NCET-10-0023)supported by the Program for New Century Excellent Talents in University of ChinaProject(J201103)supported by the Program for Hongliu Outstanding Talents of Lanzhou University of Technology,China
文摘The microstructures and crystal growth directions of permanent mould casting（PMC） and directionally solidified（DS） Al-Cu alloys with different contents of Cu were investigated. Simultaneously, the effects of pouring temperature on the microstructure and crystal growth direction of permanent mould casting pure Al were also discussed. The results indicate that the α（Al） crystals in the pure Al do not always keep common columnar grains, but change from the columnar grains to columnar dendrites with developed arms as the pouring temperature rises. The growth direction also varies with the change of pouring temperature. Cu element has similar effects on the microstructures of the PMC and DS casting Al-Cu alloys and the α（Al） crystals gradually change from columnar crystals in turn to columnar dendrites and developed equiaxed dendrites as the Cu content increases. The crystal growth direction in the PMC alloys gradually approaches （110） orientation with increasing Cu content. But the resulting crystals with growth direction of （110） do not belong to feathery grains. There are also no feathery grains to form in all of the DS Al-Cu alloys.
基金financially supported by the National Natural Science Foundation of China(Grant No.51061010)the Program for New Century Excellent Talents in University of China(Grant No.NCET-10-0023)the Program for Hongliu Outstanding Talents of Lanzhou University of Technology
文摘The microstructures and crystal growth directions of permanent mould casting and directionally solidified Al-Mg al oys with different Mg contents have been investigated. The results indicate that the effect of Mg content on microstructure is basical y same for the al oys prepared by these two methods. The primary grains change from cel ular crystals to developed columnar dendrites, and then to equiaxed dendrites as the Mg content is increased. Simultaneously, both the cel ular or columnar grain region and the primary trunk spacing decrease. Al of these changes are mainly attributed to the constitutional supercooling resulting from Mg element. Comparatively, the cellular or columnar crystals of the directionally solidified alloys are straighter and more paral el than those of the permanent mould casting al oys. These have straight or wavy grain boundaries, one of the most important microstructure characteristics of feathery grains. However, the transverse microstructure and growth direction reveal that they do not belong to feathery grains. The Mg seemingly can affect the crystal growth direction, but does not result in the formation of feathery grains under the conditions employed in the study.
文摘Model study is an efficient method for optimizing the siructure of the mould and the submerged entry nozzle (SEN). Based on the similarity criteria, a full-scale water model has been established in accordance with the mould of thin-slab caster of the CSP (Compact Strip Production) operation. The effects of SEN structure including outlet area, outflow angle, nozzle width, thick-ness and immersion depth have been studied under high speed casting by measuring the amplitude and the impetus of top waves. By the orthogonal experiment design, not only the influence of the faCtors was estimated, but also the optimum work condition was judged. The rules of the fluid flow phenomena were summarized. The principle for choosing a reasonable structure of SEN was discussed.
基金Item Sponsored by National Natural Science Foundation of China(51004012)National High-Tech Research and Development Program (863 Program) of China (2009AA04Z134)China Postdoctoral Science Foundation (2012M520621)
文摘Lubrication and friction between the mould and strand are strongly influenced by mould oscillation, and play an important role in slab quality and operating safety during continuous casting processes. Investigation of mould oscillation is therefore essential for getting a better online control of the mould processes. A feasible approach for the development and optimization of mould oscillation was put forward, which combined online measurement of mould friction, design of negative oscillating parameters and evaluation for powder consumption. Three different control models including sinusoidal and non-sinusoidal oscillation for mould oscillations were developed to investigate and evaluate the effects of oscillation on mould friction and powder lubrication. For the purpose of investigating mould friction between mould and strand, online measurement was carried out on a slab continuous caster equipped with a hydraulic oscillator. Also the comparison of the mould friction in sinusoidal and non-sinusoidal mould oscillation was made for subsequent analysis. The industrial experiment result shows that the combination of inverse control model and non-sinusoidal oscillation mode will contribute to the proper powder consumption, leading to a suitable effect of friction force on strand surface, especially for high speed continuous casting. The proposed method provides reliable basis for guiding and optimizing mould oscillation among control models, sinusoidal oscillation and non-sinusoidal oscillation.
文摘The formation and propagation of the popular off-corner subsurface cracks in bloom continuous casting were investigated through thermo-mechanical analysis using three coupled thermo-mechanical models. A two-dimensional thermo-elasto-visco-plastic finite element model was developed to predict the mould gap evolution, temperature profiles and deformation behavior of the solidified shell in the mould region. Then, a three-dimensional model was adopted to calculate the shell growth, tempera- ture history and the development of stresses and strains of the shell in the following secondary cooling zones. Finally, another three-dimensional model was used to analyze the stress distributions in the straightening region, The results showed that the off-corner cracks in the shell originated from the mould owing to the tensile strain developed in the crack sensitive regions of the solidification front, and they could be driven deeper by the possible severe surface temperature rebound and the extensive tensile stress in the secondary cooling zone, especially upon the straightening operation of the bloom casting. It is revealed that more homogenous shell temperature and thickness can be obtained through optimization of mould corner radius, casting speed and secondary cooling scheme, which help to decrease stress and strain concentration and therefore prevent the initiation of the cracks.
文摘Immersion of automotive parts in a fluidized bed of foundry sand is used to both strip the castings free from moulding sand and to heat-treat the castings at 500℃. The fluid bed is heated by hot gases from a burner directed first into a serpentine heat exchanger located near one side-wall of the rectangular tank, and then into a distributor consisting of horizontal sparger pipes having maintenance standpipes fixed into their upper surfaces.
