Optical chaos has attracted widespread attention owing to its complex dynamic behaviors.However,the time delay signature(TDS)caused by the external cavity mode reduces the complexity of optical chaos.We propose and nu...Optical chaos has attracted widespread attention owing to its complex dynamic behaviors.However,the time delay signature(TDS)caused by the external cavity mode reduces the complexity of optical chaos.We propose and numerically demonstrate the critical dispersion of chirped fiber Bragg grating(CFBG)for eliminating the TDS of laser chaos in this work.The critical dispersion,as a function of relaxation frequency and bandwidth of the optical spectrum,is found through extensive dynamics simulations.It is shown that the TDS can be eliminated when the dispersion of CFBG is above this critical dispersion.In addition,the influence of dispersive feedback light and output light from a laser is investigated.These results provide important quantitative guidance for designing chaotic semiconductor lasers without TDS.展开更多
In this paper,we propose the novel system of multipoint measurement.The sensors of measurements are chirped Bragg grating and the interrogation of sensors is sub-carrier phase.The wavelength division multiplexing tech...In this paper,we propose the novel system of multipoint measurement.The sensors of measurements are chirped Bragg grating and the interrogation of sensors is sub-carrier phase.The wavelength division multiplexing technique is used for addressing a network of FBG sensors and the time-division multiplexing technique is used for multipoint measurements.In the system,the modulation frequency of 200 MHz is adopted.The range of dectetion is from 0 to 900μεand the resolution is 12με. The time of the sensor response is about 1ns.展开更多
We propose a novel lumped time-delay compensation scheme for all-optical analog-to-digital conversion based on soliton self-frequency shift and optical interconnection techniques. A linearly chirped fiber Bragg gratin...We propose a novel lumped time-delay compensation scheme for all-optical analog-to-digital conversion based on soliton self-frequency shift and optical interconnection techniques. A linearly chirped fiber Bragg grating is optimally designed and used to compensate for the entire time-delays of the quantized pulses precisely. Simulation results show that the compensated coding pulses are well synchronized with a time difference less than 3.3 ps, which can support a maximum sampling rate of 151.52 GSa/s. The proposed scheme can efficiently reduce the structure complexity and cost of all-optical analog-to-digital conversion compared to the previous schemes with multiple optical time-delay lines.展开更多
A chirped fibre Bragg grating according to ITU-T suggested L-band （2nd channel λ1 = 1570.83 nm; 80th channel λ2 = 1603.57 nm） with more than 1800 ps/nm single channel dispersion compensation is presented in this p...A chirped fibre Bragg grating according to ITU-T suggested L-band （2nd channel λ1 = 1570.83 nm; 80th channel λ2 = 1603.57 nm） with more than 1800 ps/nm single channel dispersion compensation is presented in this paper, of which the cladding mode loss, the delay curve ripple and the power fluctuation of the reflected spectrum are less than 0.5 dB, 50 ps and 0.25 dB, respectively. With this new FBG as dispersion compensation device, a 2 × 10 Gb/s wavelength division multiplexing （WDM） L-band transmission of 600 km based on conventional single mode fibre （G.652 fibre） is performed without forward error correction. The bit error rate （BER） is less than 10-12 and the power penalties of the 2nd and 80th channel of L-band are 1.8 dB and 2.0 dB, respectively.展开更多
Chirped fibre Bragg gratings （CFBGs） are required to be concatenated to compensate the fibre dispersion in the dense wavelength-division multiplexing （DWDM） systems. When the channel spacing is small, the performa...Chirped fibre Bragg gratings （CFBGs） are required to be concatenated to compensate the fibre dispersion in the dense wavelength-division multiplexing （DWDM） systems. When the channel spacing is small, the performance of CFBGs is degraded, which restricts the usage of fibre gratings. The origin of the interactions between the gratings is analysed and methods of suppressing the interactions are also proposed.展开更多
Vector bending sensing has been consistently growing in many fields.A low-cost and high sensitivity vector bending sensor based on a chirped long-period fiber grating[LPFG]with an off-axis micro helix taper is propose...Vector bending sensing has been consistently growing in many fields.A low-cost and high sensitivity vector bending sensor based on a chirped long-period fiber grating[LPFG]with an off-axis micro helix taper is proposed and experimentally demonstrated.The grating is composed of several sections of single-mode fiber with gradually larger lengths,and the off-axis micro helix tapers with fixed lengths when they are fabricated by using the arc discharge technology.The large refractive index modulation in the micro-helix taper greatly reduces the sensor size.The total length of the sensor is only 4.67 mm.The micro-helix taper-based LPFG can identify the bending direction due to the asymmetric structure introduced by the micro helix.The experimental results show that the transmission spectra of the sensor have distinct responses for different bending directions,and the maximum bending sensitivity is 14.08 nm/m^(-1)in the range from 0.128 m^(-1)to 1.28 m^(-1).The proposed bending sensor possesses pronounced advantages,such as high sensitivity,small size,low cost,and orientation identification,and offers a very promising method for bend measurement.展开更多
The system of a true-time delay line for X-band and 8-unit phased array antennas is introduced. Changing the length of a chirp grating with piezotranslator(PZT), the variable delay is obtained. The scheme is applied t...The system of a true-time delay line for X-band and 8-unit phased array antennas is introduced. Changing the length of a chirp grating with piezotranslator(PZT), the variable delay is obtained. The scheme is applied to X-band phased array radar whose searching data rate is 56/s. It is simulated that the beam squinting is influenced by the error of real time delay. The relation between the beamforming mode and its modifying volt is discussed.展开更多
The analysis of the group delay ripple (GDR) generated by chirped fiber gratings is developed based on the Fabry-Perot (F-P) resonator. It shows clearly how the GDR is generated and why the periods of GDR varies along...The analysis of the group delay ripple (GDR) generated by chirped fiber gratings is developed based on the Fabry-Perot (F-P) resonator. It shows clearly how the GDR is generated and why the periods of GDR varies along the chirped fiber gratings. It could also explain why apodization could suppress the GDR and how apodization affects the chirp of the grating. The theory could be used to devise the apodization of fiber gratings.展开更多
A wavelength-swept fiber laser is proposed and successfully demonstrated based on a bidirectional used linear chirped fiber Bragg grating(LC-FBG). The wavelength-swept operation principle is based on intracavity pulse...A wavelength-swept fiber laser is proposed and successfully demonstrated based on a bidirectional used linear chirped fiber Bragg grating(LC-FBG). The wavelength-swept operation principle is based on intracavity pulse stretching and compression. The LC-FBG can introduce equivalent positive and negative dispersion simultaneously, which enables a perfect dispersion matching to obtain wide-bandwidth mode-locking. Experimental results demonstrate a wavelength-swept fiber laser that exhibits a sweep rate of about 5.4 MHz over a 2.1 nm range at a center wavelength of 1550 nm. It has the advantages of simple configuration and perfect dispersion matching in the laser cavity.展开更多
At first, we systematically sum up and deduce the figure of merit of the compensator using linearly chirped fiber gratings. Secondly, we solve the Reccatti differential equation by the Runge Kutta method and calcul...At first, we systematically sum up and deduce the figure of merit of the compensator using linearly chirped fiber gratings. Secondly, we solve the Reccatti differential equation by the Runge Kutta method and calculate the reflectivity and dispersion of the linearly chirped fiber gratings to obtain the figure of merit numericallu.On the other hand, we also discuss the figure of merit under the circumstances of three kinds of coupling coefficients and compare them Finally, we present one kind of perfect design of the compensator using the Gauss coupling function, and simply discuss the method to realize the Gauss coupling function in the fabrication of linearly chirped fiber gratings in this paper.展开更多
A simple nanostrain direct current （DC） measurement system based on a chirped Bragg grating Fabry-Perot （FP） structure is presented. The FP cavity, formed between the chirped fiber Bragg grating （CFBG） and the f...A simple nanostrain direct current （DC） measurement system based on a chirped Bragg grating Fabry-Perot （FP） structure is presented. The FP cavity, formed between the chirped fiber Bragg grating （CFBG） and the fiber end face, presents an aperiodic behavior due to the CFBG. A laser located in the fringe pattern slope is used to interrogate the sensing head. The optical power parameter is analyzed when strain is applied, for long and short period fringe pattern wavelengths, and sensitivities of-2.87 μW/με and-5.48μW/με are respectively obtained. This configuration presents a resolution of 70 ε.展开更多
A tunable polarization mode dispersion (PMD) compensator based on strain-ckirped fiber Bragg gratings (FBGs) is proposed. It natures in flexible designing, large tuning range, without using linear or nonlinear chirped...A tunable polarization mode dispersion (PMD) compensator based on strain-ckirped fiber Bragg gratings (FBGs) is proposed. It natures in flexible designing, large tuning range, without using linear or nonlinear chirped phase mask, fast tuning response time, continuously adjustable, all-fiber based, compact, and cheap.展开更多
When femtosecond laser pulses interfere with chirped femtosecond laser pulses in As2S3 fiber, a chirped fiber grating is formed. An analytical expression is given to describe the chirped grating, and its Bragg reflect...When femtosecond laser pulses interfere with chirped femtosecond laser pulses in As2S3 fiber, a chirped fiber grating is formed. An analytical expression is given to describe the chirped grating, and its Bragg reflectivity is calculated. Because of the high photosensitive effect of As2S3 material, the chirped fiber grating has a wide Bragg reflective spectrum and high reflectivity by choosing proper parameters. This indicates that the chirped fiber grating can be used as a stretcher in the femtosecond chirped pulse amplification (CPA) system.展开更多
-We describe a simple method to generate wavelength-tunable pulses by using a semiconductor optical amplifier (SOA) as an intensity modulator and a gain medium. Wavelength tunable pulses at a repetition rate of 4.8 GH...-We describe a simple method to generate wavelength-tunable pulses by using a semiconductor optical amplifier (SOA) as an intensity modulator and a gain medium. Wavelength tunable pulses at a repetition rate of 4.8 GHz have been generated.展开更多
Many methods have been suggested to reduce dispersion in optical fiber communication. Among these methods, chirped fiber grating (CFG) is a promising scheme. This paper describes a linearly chirped fiber grating with...Many methods have been suggested to reduce dispersion in optical fiber communication. Among these methods, chirped fiber grating (CFG) is a promising scheme. This paper describes a linearly chirped fiber grating with 95% reflectivity and 0.3 nm bandwidth written using a double exposure method with a uniform phase mask. The CFG resonant wavelength is 1554.5 nm and dispersion is 1700 ps/nm. Dispersion compensation in a 10-Gb/s optical transmission system has been demonstrated using this chirped fiber grating. The power penalty induced by the dispersion compensation after 180-km transmission is 1 dB. This is the first report describing dispersion compensation of 180 km at 10-Gb/s optical transmission now-return to zero (NRZ) system in China.展开更多
An optic-fiber liquid-level sensor based on tapered chirped grating was proposed and demonstrated experimentally.With a properly designed column buoy hung to chain wheel,the liquid-level variation was converted to axi...An optic-fiber liquid-level sensor based on tapered chirped grating was proposed and demonstrated experimentally.With a properly designed column buoy hung to chain wheel,the liquid-level variation was converted to axial strain,which made the reflection spectrum of the tapered chirped grating narrowed or broadened correspondingly.And a high-sensitive liquid-level sensor was obtained by monitoring the bandwidth variation of the tapered chirped grating.Compared with traditional absolute wavelength or power detection,this special monitoring technique based on bandwidth modulation makes the liquid-level sensor insensitive to spatially uniform temperature variations and power fluctuations from down-lead or light source.展开更多
This paper proposed and experimentally demonstrated an all-fiber tunable and programmable bandpass filter using a linearly chirped fiber Bragg grating （CFBG）. The center wavelength and spacing of the transmission pe...This paper proposed and experimentally demonstrated an all-fiber tunable and programmable bandpass filter using a linearly chirped fiber Bragg grating （CFBG）. The center wavelength and spacing of the transmission peaks could be independently tuned via computer. The tunable range is about 18 rim. With this filter we demonstrated a tunable fiber ring laser which has an output power of about -7 dBm, full-width at half- maximum linewidth of-0.017 nm which is limited by the resolution of the optical spectrum analyzer （OSA）. Furthermore, a spacing tunable dual-wavelength fiber laser was achieved with the same setup. This all-fiber laser features advantages like simple structure, low cost, flexible and digital tuning capability.展开更多
A 10 Gbit/s recirculating system is configured with Chirped Fiber Bragg Grating (CFBG) for the dispersion compensation. For the first time, the transmission distance in the loop reaches 1000km with bit error rate of 1...A 10 Gbit/s recirculating system is configured with Chirped Fiber Bragg Grating (CFBG) for the dispersion compensation. For the first time, the transmission distance in the loop reaches 1000km with bit error rate of 10-9. The effect of the group delay ripple of the fiber grating is also investigated in the recirculating systems, and it is shown that the transmission distance is limited to 4 cycles (4× 167.1km ) in the loop with the power penalty fluctuation below 1.0dB. Thus the group delay ripple should be reduced to allow for the wavelength drift of ±5GHz.At the end of this letter, the principles are given for designing long haul recirculating systems with dispersion compensation CFBG.展开更多
A novel variety of three dimensional （3D） vibration sensor based on chirped fiber Bragg grating （CFBG） is developed to measure 3D vibration in the mechanical equipment field. The sensor is composed of three indepe...A novel variety of three dimensional （3D） vibration sensor based on chirped fiber Bragg grating （CFBG） is developed to measure 3D vibration in the mechanical equipment field. The sensor is composed of three independent vibration sensing units. Each unit uses double matched chirped gratings as sensing elements, and the sensing signal is processed by the edge filtering demodulation method. The structure and principle of the sensor are theoretically analyzed, and its performances are obtained from some experiments and the results are as follows： operating frequency range of the sensor is 10Hz - 500Hz; acceleration measurement range is 2m.s-2 - 30m.s-2; sensitivity is about 70 mV/m.s-2; crosstalk coefficient is greater than 22 dB; self-compensation for temperature is available. Eventually the sensor is applied to monitor the vibration state of radiation pump. Seen from its experiments and applications, the sensor has good sensing performances, which can meet a certain requirement for some engineering measurement.展开更多
基金the National Natural Science Foundation of China(Grant No.62105190)the Natural Science Foundation of Shanxi Province of China(Grant No.20210302124268)+1 种基金the Scientific and Technological Innovation Programs of Higher Education Institutions of Shanxi Province of China(Grant No.2021L285)the Youth Researchof Shanxi University of Finance and Economics(Grant No.QN-202015)。
文摘Optical chaos has attracted widespread attention owing to its complex dynamic behaviors.However,the time delay signature(TDS)caused by the external cavity mode reduces the complexity of optical chaos.We propose and numerically demonstrate the critical dispersion of chirped fiber Bragg grating(CFBG)for eliminating the TDS of laser chaos in this work.The critical dispersion,as a function of relaxation frequency and bandwidth of the optical spectrum,is found through extensive dynamics simulations.It is shown that the TDS can be eliminated when the dispersion of CFBG is above this critical dispersion.In addition,the influence of dispersive feedback light and output light from a laser is investigated.These results provide important quantitative guidance for designing chaotic semiconductor lasers without TDS.
文摘In this paper,we propose the novel system of multipoint measurement.The sensors of measurements are chirped Bragg grating and the interrogation of sensors is sub-carrier phase.The wavelength division multiplexing technique is used for addressing a network of FBG sensors and the time-division multiplexing technique is used for multipoint measurements.In the system,the modulation frequency of 200 MHz is adopted.The range of dectetion is from 0 to 900μεand the resolution is 12με. The time of the sensor response is about 1ns.
基金Project supported by the National Basic Research Program,China(Grant Nos.2010CB327605 and 2010CB328300)the National High-Technology Research and Development Program of China(Grant No.2013AA031501)+7 种基金the National Natural Science Foundation of China(Grant No.61307109)the Specialized Research Fund for the Doctoral Program of Higher Education of China(Grant No.20120005120021)the Fundamental Research Funds for the Central Universities,China(Grant No.2013RC1202)the Program for New Century Excellent Talents in University,China(Grant No.NECT-11-0596)the Beijing Nova Program,China(Grant No.2011066)the Fund of State Key Laboratory of Information Photonics and Optical Communications(Beijing University of Posts and Telecommunications) Chinathe China Postdoctoral Science Foundation(Grant No.2012M511826)the Postdoctoral Science Foundation of Guangdong Province,China(Grant No.244331)
文摘We propose a novel lumped time-delay compensation scheme for all-optical analog-to-digital conversion based on soliton self-frequency shift and optical interconnection techniques. A linearly chirped fiber Bragg grating is optimally designed and used to compensate for the entire time-delays of the quantized pulses precisely. Simulation results show that the compensated coding pulses are well synchronized with a time difference less than 3.3 ps, which can support a maximum sampling rate of 151.52 GSa/s. The proposed scheme can efficiently reduce the structure complexity and cost of all-optical analog-to-digital conversion compared to the previous schemes with multiple optical time-delay lines.
文摘A chirped fibre Bragg grating according to ITU-T suggested L-band （2nd channel λ1 = 1570.83 nm; 80th channel λ2 = 1603.57 nm） with more than 1800 ps/nm single channel dispersion compensation is presented in this paper, of which the cladding mode loss, the delay curve ripple and the power fluctuation of the reflected spectrum are less than 0.5 dB, 50 ps and 0.25 dB, respectively. With this new FBG as dispersion compensation device, a 2 × 10 Gb/s wavelength division multiplexing （WDM） L-band transmission of 600 km based on conventional single mode fibre （G.652 fibre） is performed without forward error correction. The bit error rate （BER） is less than 10-12 and the power penalties of the 2nd and 80th channel of L-band are 1.8 dB and 2.0 dB, respectively.
文摘Chirped fibre Bragg gratings （CFBGs） are required to be concatenated to compensate the fibre dispersion in the dense wavelength-division multiplexing （DWDM） systems. When the channel spacing is small, the performance of CFBGs is degraded, which restricts the usage of fibre gratings. The origin of the interactions between the gratings is analysed and methods of suppressing the interactions are also proposed.
基金supported in part by the National Natural Science Foundation of China(NSFC)(Nos.62205087,62175049,and 62105077)Natural Science Foundation of Heilongjiang Province in China(No.YQ2021F002)+1 种基金Fundamental Research Funds for the Central Universities(Nos.3072022TS2501 and 3072021CFJ2504)China Postdoctoral Science Foundation(No.2022M710933)。
文摘Vector bending sensing has been consistently growing in many fields.A low-cost and high sensitivity vector bending sensor based on a chirped long-period fiber grating[LPFG]with an off-axis micro helix taper is proposed and experimentally demonstrated.The grating is composed of several sections of single-mode fiber with gradually larger lengths,and the off-axis micro helix tapers with fixed lengths when they are fabricated by using the arc discharge technology.The large refractive index modulation in the micro-helix taper greatly reduces the sensor size.The total length of the sensor is only 4.67 mm.The micro-helix taper-based LPFG can identify the bending direction due to the asymmetric structure introduced by the micro helix.The experimental results show that the transmission spectra of the sensor have distinct responses for different bending directions,and the maximum bending sensitivity is 14.08 nm/m^(-1)in the range from 0.128 m^(-1)to 1.28 m^(-1).The proposed bending sensor possesses pronounced advantages,such as high sensitivity,small size,low cost,and orientation identification,and offers a very promising method for bend measurement.
基金Natural Science Foundation from Universities in Jiangsu Province(06KJD510034)
文摘The system of a true-time delay line for X-band and 8-unit phased array antennas is introduced. Changing the length of a chirp grating with piezotranslator(PZT), the variable delay is obtained. The scheme is applied to X-band phased array radar whose searching data rate is 56/s. It is simulated that the beam squinting is influenced by the error of real time delay. The relation between the beamforming mode and its modifying volt is discussed.
基金This work was supported by the National 863 Plan(2001AA120201)
文摘The analysis of the group delay ripple (GDR) generated by chirped fiber gratings is developed based on the Fabry-Perot (F-P) resonator. It shows clearly how the GDR is generated and why the periods of GDR varies along the chirped fiber gratings. It could also explain why apodization could suppress the GDR and how apodization affects the chirp of the grating. The theory could be used to devise the apodization of fiber gratings.
基金National Natural Science Foundation of China(NSFC)(61475065)Natural Science Foundation of Guangdong Province(2015A030313322)
文摘A wavelength-swept fiber laser is proposed and successfully demonstrated based on a bidirectional used linear chirped fiber Bragg grating(LC-FBG). The wavelength-swept operation principle is based on intracavity pulse stretching and compression. The LC-FBG can introduce equivalent positive and negative dispersion simultaneously, which enables a perfect dispersion matching to obtain wide-bandwidth mode-locking. Experimental results demonstrate a wavelength-swept fiber laser that exhibits a sweep rate of about 5.4 MHz over a 2.1 nm range at a center wavelength of 1550 nm. It has the advantages of simple configuration and perfect dispersion matching in the laser cavity.
文摘At first, we systematically sum up and deduce the figure of merit of the compensator using linearly chirped fiber gratings. Secondly, we solve the Reccatti differential equation by the Runge Kutta method and calculate the reflectivity and dispersion of the linearly chirped fiber gratings to obtain the figure of merit numericallu.On the other hand, we also discuss the figure of merit under the circumstances of three kinds of coupling coefficients and compare them Finally, we present one kind of perfect design of the compensator using the Gauss coupling function, and simply discuss the method to realize the Gauss coupling function in the fabrication of linearly chirped fiber gratings in this paper.
文摘A simple nanostrain direct current （DC） measurement system based on a chirped Bragg grating Fabry-Perot （FP） structure is presented. The FP cavity, formed between the chirped fiber Bragg grating （CFBG） and the fiber end face, presents an aperiodic behavior due to the CFBG. A laser located in the fringe pattern slope is used to interrogate the sensing head. The optical power parameter is analyzed when strain is applied, for long and short period fringe pattern wavelengths, and sensitivities of-2.87 μW/με and-5.48μW/με are respectively obtained. This configuration presents a resolution of 70 ε.
基金This work was supported by the National 973 Basic Research and Development Program of China (No. 2003CB314901), the National Natural Science Foundation of China (No. 60377026), the National "863" High Technology Project of China (No. 2003AA311070),
文摘A tunable polarization mode dispersion (PMD) compensator based on strain-ckirped fiber Bragg gratings (FBGs) is proposed. It natures in flexible designing, large tuning range, without using linear or nonlinear chirped phase mask, fast tuning response time, continuously adjustable, all-fiber based, compact, and cheap.
基金The authors acknowledge the support of the National Key Basic Research Special Foundation of China (No. G1999075201-2)the National Natural Science Foundation of China (No. 60178007)the Science Foundation of China for Post Ph. D (2002032163).
文摘When femtosecond laser pulses interfere with chirped femtosecond laser pulses in As2S3 fiber, a chirped fiber grating is formed. An analytical expression is given to describe the chirped grating, and its Bragg reflectivity is calculated. Because of the high photosensitive effect of As2S3 material, the chirped fiber grating has a wide Bragg reflective spectrum and high reflectivity by choosing proper parameters. This indicates that the chirped fiber grating can be used as a stretcher in the femtosecond chirped pulse amplification (CPA) system.
文摘-We describe a simple method to generate wavelength-tunable pulses by using a semiconductor optical amplifier (SOA) as an intensity modulator and a gain medium. Wavelength tunable pulses at a repetition rate of 4.8 GHz have been generated.
文摘Many methods have been suggested to reduce dispersion in optical fiber communication. Among these methods, chirped fiber grating (CFG) is a promising scheme. This paper describes a linearly chirped fiber grating with 95% reflectivity and 0.3 nm bandwidth written using a double exposure method with a uniform phase mask. The CFG resonant wavelength is 1554.5 nm and dispersion is 1700 ps/nm. Dispersion compensation in a 10-Gb/s optical transmission system has been demonstrated using this chirped fiber grating. The power penalty induced by the dispersion compensation after 180-km transmission is 1 dB. This is the first report describing dispersion compensation of 180 km at 10-Gb/s optical transmission now-return to zero (NRZ) system in China.
基金supported by the National Natural Science Foundation of China (Grant No. 61007007)the Fundation of BeiJing Municipal Committee of CPC Organization Department (Grant No. 2012D005002-000001)
文摘An optic-fiber liquid-level sensor based on tapered chirped grating was proposed and demonstrated experimentally.With a properly designed column buoy hung to chain wheel,the liquid-level variation was converted to axial strain,which made the reflection spectrum of the tapered chirped grating narrowed or broadened correspondingly.And a high-sensitive liquid-level sensor was obtained by monitoring the bandwidth variation of the tapered chirped grating.Compared with traditional absolute wavelength or power detection,this special monitoring technique based on bandwidth modulation makes the liquid-level sensor insensitive to spatially uniform temperature variations and power fluctuations from down-lead or light source.
基金Acknowledgements This work was supported by the National Natural Science Foundation of China （Grant No. 61107087） and the National High Technology Research and Development Program of China （863 Program） （No. SS2012AA010407）.
文摘This paper proposed and experimentally demonstrated an all-fiber tunable and programmable bandpass filter using a linearly chirped fiber Bragg grating （CFBG）. The center wavelength and spacing of the transmission peaks could be independently tuned via computer. The tunable range is about 18 rim. With this filter we demonstrated a tunable fiber ring laser which has an output power of about -7 dBm, full-width at half- maximum linewidth of-0.017 nm which is limited by the resolution of the optical spectrum analyzer （OSA）. Furthermore, a spacing tunable dual-wavelength fiber laser was achieved with the same setup. This all-fiber laser features advantages like simple structure, low cost, flexible and digital tuning capability.
基金the National 863 High Technology Development Program of China (No.2001 AA122012)
文摘A 10 Gbit/s recirculating system is configured with Chirped Fiber Bragg Grating (CFBG) for the dispersion compensation. For the first time, the transmission distance in the loop reaches 1000km with bit error rate of 10-9. The effect of the group delay ripple of the fiber grating is also investigated in the recirculating systems, and it is shown that the transmission distance is limited to 4 cycles (4× 167.1km ) in the loop with the power penalty fluctuation below 1.0dB. Thus the group delay ripple should be reduced to allow for the wavelength drift of ±5GHz.At the end of this letter, the principles are given for designing long haul recirculating systems with dispersion compensation CFBG.
基金This research was funded by the Key Project of National Science Foundation of China, Award Number： 61290311.
文摘A novel variety of three dimensional （3D） vibration sensor based on chirped fiber Bragg grating （CFBG） is developed to measure 3D vibration in the mechanical equipment field. The sensor is composed of three independent vibration sensing units. Each unit uses double matched chirped gratings as sensing elements, and the sensing signal is processed by the edge filtering demodulation method. The structure and principle of the sensor are theoretically analyzed, and its performances are obtained from some experiments and the results are as follows： operating frequency range of the sensor is 10Hz - 500Hz; acceleration measurement range is 2m.s-2 - 30m.s-2; sensitivity is about 70 mV/m.s-2; crosstalk coefficient is greater than 22 dB; self-compensation for temperature is available. Eventually the sensor is applied to monitor the vibration state of radiation pump. Seen from its experiments and applications, the sensor has good sensing performances, which can meet a certain requirement for some engineering measurement.
