In order to study the factors that influence the air fuel ratio(A/F), the amplitude and frequency of A/F fluctuation, to reform the control strategy, and to improve the efficiency of three way catalyst(TWC), a model...In order to study the factors that influence the air fuel ratio(A/F), the amplitude and frequency of A/F fluctuation, to reform the control strategy, and to improve the efficiency of three way catalyst(TWC), a model of closed loop control system including the engine, air fuel mixing and transportation, oxygen sensor and controller, etc., is developed. Various factors that influence the A/F control are studied by simulation. The simulation results show that the reference voltage of oxygen sensor will influence the mean value of A/F ratio, the controller parameters will influence the amplitude of A/F fluctuation, and the operating conditions of the engine determine the frequency of A/F fluctuations, the amplitude of A/F fluctuation can be reduced to within demanded values by logical selection of the signal acquisition method and controller parameters. Higher A/F fluctuation frequency under high speed and load can be reduced through software delay in the controller. The A/F closed loop control system based on the simulation results, accompanied with a rare earth element TWC, gives a better efficiency of conversion against harmful emissions.展开更多
In order to improve the steady state performance,dynamic response and power factor of traditional power factor correction(PFC)digital control method and reduce the harmonic distortion of input current,a double closed ...In order to improve the steady state performance,dynamic response and power factor of traditional power factor correction(PFC)digital control method and reduce the harmonic distortion of input current,a double closed loop active power factorcorrection(APFC)control method with feed-forward is proposed.Firstly,the small signal model of Boost PFC control systemis built and the system transfer function is deduced,and then the parameters of the main device with Boost topology is estimated.By means of the feed-forward,the system can quickly respond to the change in input voltage.Furthermore,the use ofvoltage loop and current loop can achieve input current and output voltage regulation Simulink modeling shows that this methodcan effectively control the output voltage in case of input voltage largely fluctuating,improve the system dynamic response abilityand input power factor,and reduce the input current harmonic distortion展开更多
With a focus on an industrial multivariable system, two subsystems including the flow and the level outputs are analysed and controlled, which have applicability in both real and academic environments. In such a case,...With a focus on an industrial multivariable system, two subsystems including the flow and the level outputs are analysed and controlled, which have applicability in both real and academic environments. In such a case, at first, each subsystem is distinctively represented by its model, since the outcomes point out that the chosen models have the same behavior as corresponding ones. Then, the industrial multivariable system and its presentation are achieved in line with the integration of these subsystems, since the interaction between them can not actually be ignored. To analyze the interaction presented, the Gershgorin bands need to be acquired, where the results are used to modify the system parameters to appropriate values. Subsequently, in the view of modeling results, the control concept in two different techniques including sequential loop closing control(SLCC) scheme and diagonal dominance control(DDC) schemes is proposed to implement on the system through the Profibus network, as long as the OPC(OLE for process control) server is utilized to communicate between the control schemes presented and the multivariable system. The real test scenarios are carried out and the corresponding outcomes in their present forms are acquired. In the same way, the proposed control schemes results are compared with each other, where the real consequences verify the validity of them in the field of the presented industrial multivariable system control.展开更多
The closed loop control model was built up for compensating the springback and enhancing the work piece precision.A coupled closed loop algorithm and a finite element method were developed to simulate and correct the ...The closed loop control model was built up for compensating the springback and enhancing the work piece precision.A coupled closed loop algorithm and a finite element method were developed to simulate and correct the springback of incremental sheet forming.A three-dimensional finite element model was established for simulation of springback in incremental sheet forming process.The closed loop algorithm of trajectory profile for the incremental sheet forming based on the wavelet transform combined with fast Fourier transform was constructed.The profile of processing tool path of shallow dishing with spherical surface was designed on the basis of the profile correction algorithm.The result shows that the algorithm can predict an ideal profile of processing track,and the springback error of incremental sheet forming is eliminated effectively.It has good convergence efficiency,and can improve the workpiece dimensional accuracy greatly.展开更多
The attitude tracking control problem for a satellite with parameter uncertainties and external disturbances is considered in this paper. For this class of multi-input multi-output uncertain nonlinear systems, a desig...The attitude tracking control problem for a satellite with parameter uncertainties and external disturbances is considered in this paper. For this class of multi-input multi-output uncertain nonlinear systems, a design method of robust output tracking controllers is proposed based on the upper-bounds of the uncertainties. Using the input/output feedback linearization approach and Lyapunov method, a control law is designed, which guarantees that the system output exponentially tracks the given desired output. The proposed controller is easy to compute and complement. Simulation results show that, in the closed-loop system, precise attitude control is accomplished in spite of the uncertainties in the system.展开更多
The problem of robust stabilization for nonlinear systems with partially known uncertainties is considered in this paper. The required information about uncertainties in the system is merely that the uncertainties are...The problem of robust stabilization for nonlinear systems with partially known uncertainties is considered in this paper. The required information about uncertainties in the system is merely that the uncertainties are bounded, but the upper bounds are incompletely known. This paper can be viewed as an extension of the work in reference [1]. To compensate the uncertainties, an adaptive robust controller based on Lyapunov method is proposed and the design algorithm is also suggested. Compared with some previous controllers which can only ensure ultimate uniform boundedness of the systems, the controller given in the paper can make sure that the obtained closed-loop system is asymptotically stable in the large. Simulations show that the method presented is available and effective.展开更多
A deformation measurement method of interframe displacement was proposed in this paper. By online monitoring the shape di- mensions of both the deformation zone and its adjacent zone by machine vision, the initial and...A deformation measurement method of interframe displacement was proposed in this paper. By online monitoring the shape di- mensions of both the deformation zone and its adjacent zone by machine vision, the initial and terminative positions of deformation were dynamically identified during dieless drawing, and the global monitoring and online closed-loop control of the deformation zone were achieved. The dieless drawing process was systematically carried out on NiTi shape memory alloy wires. It is shown that the deformation measurement method of interframe displacement can track the axial displacement of the wires, but this cannot be achieved by traditional machine vision. The initial and terminative positions of deformation can be accurately identified by this method. The proposed rectifying control technology can effectively decrease the wire diameter fluctuation during dieless drawing, that is, the standard deviation of the wire diameter fluctuation could be decreased fi＇om 0.30 to 0.08 mm after three passes of dieless drawing, indicating that the control system has a good rectifying ability.展开更多
This paper focuses on the H∞ controller design for linear systems with time-varying delays and norm-bounded parameter perturbations in the system state and control/disturbance. On the existence of delayed/undelayed f...This paper focuses on the H∞ controller design for linear systems with time-varying delays and norm-bounded parameter perturbations in the system state and control/disturbance. On the existence of delayed/undelayed full state feedback controllers, we present a sufficient condition and give a design method in the form of Riccati equation. The controller can not only stabilize the time-delay system, but also make the H∞ norm of the closed-loop system be less than a given bound. This result practically generalizes the related results in current literature.展开更多
In this paper, the stabilization of a linear SISO plant with variable operating condition is considered. The plant is described by a linear interpolation of proper stable co-prime factorizations of the transfer functi...In this paper, the stabilization of a linear SISO plant with variable operating condition is considered. The plant is described by a linear interpolation of proper stable co-prime factorizations of the transfer functions at two representative operating points. An interpolation of the stabilizing controllers for the representative models is designed to stabilize the plant, and the necessary and sufficient condition for the plant to be stabilized by the proposed controller is presented using the Nevanlinna-Pick interpolation theory. It is shown that the class of stabilization plants via the proposed controller in the paper is larger than that by the controller in reference. An example is also given to illustrate this fact.展开更多
Web service applications are increasing tremendously in support of high-level businesses.There must be a need of better server load balancing mechanism for improving the performance of web services in business.Though ...Web service applications are increasing tremendously in support of high-level businesses.There must be a need of better server load balancing mechanism for improving the performance of web services in business.Though many load balancing methods exist,there is still a need for sophisticated load bal-ancing mechanism for not letting the clients to get frustrated.In this work,the ser-ver with minimum response time and the server having less traffic volume were selected for the aimed server to process the forthcoming requests.The Servers are probed with adaptive control of time with two thresholds L and U to indicate the status of server load in terms of response time difference as low,medium and high load by the load balancing application.Fetching the real time responses of entire servers in the server farm is a key component of this intelligent Load balancing system.Many Load Balancing schemes are based on the graded thresholds,because the exact information about the networkflux is difficult to obtain.Using two thresholds L and U,it is possible to indicate the load on particular server as low,medium or high depending on the Maximum response time difference of the servers present in the server farm which is below L,between L and U or above U respectively.However,the existing works of load balancing in the server farm incorporatefixed time to measure real time response time,which in general are not optimal for all traffic conditions.Therefore,an algorithm based on Propor-tional Integration and Derivative neural network controller was designed with two thresholds for tuning the timing to probe the server for near optimal perfor-mance.The emulation results has shown a significant gain in the performance by tuning the threshold time.In addition to that,tuning algorithm is implemented in conjunction with Load Balancing scheme which does not tune thefixed time slots.展开更多
Through a third⁃order mathematical model of grid⁃oriented LCL⁃type converters,this paper analyzes the complicated dynamic characteristics and resonance problems which may influence the system stability.To realize acti...Through a third⁃order mathematical model of grid⁃oriented LCL⁃type converters,this paper analyzes the complicated dynamic characteristics and resonance problems which may influence the system stability.To realize active damping for LCL filters and improve dynamic performance of current regulators,a state space current PI controller is proposed whose parameters can be tuned based on the polynomial equations approach.An extended state observer is integrated with the regulation scheme,where additional sensors are not necessary in contrast with conventional active damping strategies.Synchronous reference frame PLL(SRF⁃PLL)equipped with filter technology is proposed for grid voltage disturbance suppression.This method is then applied to establish a double⁃closed⁃loop power regulator that demonstrates improved performance compared with other controllers.The simulation results are displayed to illustrate the efficiency of the regulation methods.展开更多
In this paper, the nonlinear control of chaotic oscillations was investigated by using the input output linearization control method. The chaotic attitude of a kind of spacecraft was discussed. It is demonstrated that...In this paper, the nonlinear control of chaotic oscillations was investigated by using the input output linearization control method. The chaotic attitude of a kind of spacecraft was discussed. It is demonstrated that the input output linearization control law is the nonlinear version of the parametric open plus closed loop control law.展开更多
This paper presents a novel design method of force rebalance control for the sense mode of micromachined vibratory gyroscopes.Specific theoretical deductions are performed to identify a precise linear model of the ope...This paper presents a novel design method of force rebalance control for the sense mode of micromachined vibratory gyroscopes.Specific theoretical deductions are performed to identify a precise linear model of the open loop system of the sense mode,which is crucial for the PI controller design.The frequency responses obtained by experimental tests agree well with those calculated with the theoretical model,indicating the accuracy of the theoretical analyses.Experimental results demonstrate that the bandwidth of the closed loop is extended to 94.8 Hz from 2.3 Hz in the open loop and the quadrature signal is suppressed by about 64 dBV in the closed loop system.The overshoot and stable time in the step response of the closed loop system are measured to be about 15% and 35 ms,respectively.The mode-splitting gyroscope with the closed loop controlled sense mode achieves a scale factor of 41.0 mV/deg/s with nonlinearity of 0.09% and asymmetry of 1%,and a bias instability of 4.0 °/h with angle random walk of 0.171 deg/h1/2.展开更多
A high-precision shape detecting system of cold rolling strip is developed to meet industrial application, which mainly consists of the shape detecting roller, the collecting ring, the digital signal processing （DSP...A high-precision shape detecting system of cold rolling strip is developed to meet industrial application, which mainly consists of the shape detecting roller, the collecting ring, the digital signal processing （DSP） shape signal processing board and the shape control model. Based on the shape detecting principle, the shape detecting roller is designed with a new integral structure for improving the precision of shape detecting and avoiding scratching strip surface. Based on the DSP technology, the DSP shape signal processing circuit board is designed and embedded in the shape detecting system for the reliability and stability of shape signal processing. The shape detecting system was successfully used in Angang 1 250 mm HC 6-high reversible cold rolling mill. The precision of shape detecting is 0.2 I and the shape deviation is controlled within 6 1 after the close loop shape control is input.展开更多
文摘In order to study the factors that influence the air fuel ratio(A/F), the amplitude and frequency of A/F fluctuation, to reform the control strategy, and to improve the efficiency of three way catalyst(TWC), a model of closed loop control system including the engine, air fuel mixing and transportation, oxygen sensor and controller, etc., is developed. Various factors that influence the A/F control are studied by simulation. The simulation results show that the reference voltage of oxygen sensor will influence the mean value of A/F ratio, the controller parameters will influence the amplitude of A/F fluctuation, and the operating conditions of the engine determine the frequency of A/F fluctuations, the amplitude of A/F fluctuation can be reduced to within demanded values by logical selection of the signal acquisition method and controller parameters. Higher A/F fluctuation frequency under high speed and load can be reduced through software delay in the controller. The A/F closed loop control system based on the simulation results, accompanied with a rare earth element TWC, gives a better efficiency of conversion against harmful emissions.
基金National Natural Science Foundation of China(No.61261029)
文摘In order to improve the steady state performance,dynamic response and power factor of traditional power factor correction(PFC)digital control method and reduce the harmonic distortion of input current,a double closed loop active power factorcorrection(APFC)control method with feed-forward is proposed.Firstly,the small signal model of Boost PFC control systemis built and the system transfer function is deduced,and then the parameters of the main device with Boost topology is estimated.By means of the feed-forward,the system can quickly respond to the change in input voltage.Furthermore,the use ofvoltage loop and current loop can achieve input current and output voltage regulation Simulink modeling shows that this methodcan effectively control the output voltage in case of input voltage largely fluctuating,improve the system dynamic response abilityand input power factor,and reduce the input current harmonic distortion
文摘With a focus on an industrial multivariable system, two subsystems including the flow and the level outputs are analysed and controlled, which have applicability in both real and academic environments. In such a case, at first, each subsystem is distinctively represented by its model, since the outcomes point out that the chosen models have the same behavior as corresponding ones. Then, the industrial multivariable system and its presentation are achieved in line with the integration of these subsystems, since the interaction between them can not actually be ignored. To analyze the interaction presented, the Gershgorin bands need to be acquired, where the results are used to modify the system parameters to appropriate values. Subsequently, in the view of modeling results, the control concept in two different techniques including sequential loop closing control(SLCC) scheme and diagonal dominance control(DDC) schemes is proposed to implement on the system through the Profibus network, as long as the OPC(OLE for process control) server is utilized to communicate between the control schemes presented and the multivariable system. The real test scenarios are carried out and the corresponding outcomes in their present forms are acquired. In the same way, the proposed control schemes results are compared with each other, where the real consequences verify the validity of them in the field of the presented industrial multivariable system control.
基金Project(50175034) supported by the National Natural Science Foundation of China
文摘The closed loop control model was built up for compensating the springback and enhancing the work piece precision.A coupled closed loop algorithm and a finite element method were developed to simulate and correct the springback of incremental sheet forming.A three-dimensional finite element model was established for simulation of springback in incremental sheet forming process.The closed loop algorithm of trajectory profile for the incremental sheet forming based on the wavelet transform combined with fast Fourier transform was constructed.The profile of processing tool path of shallow dishing with spherical surface was designed on the basis of the profile correction algorithm.The result shows that the algorithm can predict an ideal profile of processing track,and the springback error of incremental sheet forming is eliminated effectively.It has good convergence efficiency,and can improve the workpiece dimensional accuracy greatly.
基金supported by the Aerospace Science and Technology Innovation Foundation of China(CAST2014CH01)the Aeronautical Science Foundation of China(2015ZC560007)+1 种基金the Jiangxi Natural Science Foundation of China(20151BBE50026)National Natural Science Foundation of China(11462015)
文摘The attitude tracking control problem for a satellite with parameter uncertainties and external disturbances is considered in this paper. For this class of multi-input multi-output uncertain nonlinear systems, a design method of robust output tracking controllers is proposed based on the upper-bounds of the uncertainties. Using the input/output feedback linearization approach and Lyapunov method, a control law is designed, which guarantees that the system output exponentially tracks the given desired output. The proposed controller is easy to compute and complement. Simulation results show that, in the closed-loop system, precise attitude control is accomplished in spite of the uncertainties in the system.
基金supported by National Natural Science Foundation of China(61174102)Jiangsu Natural Science Foundation of China(SBK20130033)+1 种基金Aeronautical Science Foundation of China 20145152029)Specialized Research Fund for the Doctoral Program of Higher Education(20133218110013)
基金supported by National Natural Science Foundation of China(61104085,51505213)Natural Science Foundation of Jiangsu Province(BK20151463,BK20130744)+2 种基金Innovation Foundation of NJIT(CKJA201409,CKJB201209)sponsored by Jiangsu Qing Lan ProjectJiangsu Government Scholarship for Overseas Studies(JS-2012-051)
文摘The problem of robust stabilization for nonlinear systems with partially known uncertainties is considered in this paper. The required information about uncertainties in the system is merely that the uncertainties are bounded, but the upper bounds are incompletely known. This paper can be viewed as an extension of the work in reference [1]. To compensate the uncertainties, an adaptive robust controller based on Lyapunov method is proposed and the design algorithm is also suggested. Compared with some previous controllers which can only ensure ultimate uniform boundedness of the systems, the controller given in the paper can make sure that the obtained closed-loop system is asymptotically stable in the large. Simulations show that the method presented is available and effective.
基金financially supported by the National Basic Research Priorities Program of China (No.2011CB606300)the National Natural Science Foundation of China (Nos.50634010 and 50674008)+1 种基金the Program for New Century Excellent Talents in Chinese Universities(No.NCET-06-0083)the Universities Fundamental Research Foundation of the Ministry of Education, China (No.FRF-TP-10-002B)
文摘A deformation measurement method of interframe displacement was proposed in this paper. By online monitoring the shape di- mensions of both the deformation zone and its adjacent zone by machine vision, the initial and terminative positions of deformation were dynamically identified during dieless drawing, and the global monitoring and online closed-loop control of the deformation zone were achieved. The dieless drawing process was systematically carried out on NiTi shape memory alloy wires. It is shown that the deformation measurement method of interframe displacement can track the axial displacement of the wires, but this cannot be achieved by traditional machine vision. The initial and terminative positions of deformation can be accurately identified by this method. The proposed rectifying control technology can effectively decrease the wire diameter fluctuation during dieless drawing, that is, the standard deviation of the wire diameter fluctuation could be decreased fi＇om 0.30 to 0.08 mm after three passes of dieless drawing, indicating that the control system has a good rectifying ability.
基金This project was supported by the National Natural Science Foundation of China (No. 69974022).
文摘This paper focuses on the H∞ controller design for linear systems with time-varying delays and norm-bounded parameter perturbations in the system state and control/disturbance. On the existence of delayed/undelayed full state feedback controllers, we present a sufficient condition and give a design method in the form of Riccati equation. The controller can not only stabilize the time-delay system, but also make the H∞ norm of the closed-loop system be less than a given bound. This result practically generalizes the related results in current literature.
文摘In this paper, the stabilization of a linear SISO plant with variable operating condition is considered. The plant is described by a linear interpolation of proper stable co-prime factorizations of the transfer functions at two representative operating points. An interpolation of the stabilizing controllers for the representative models is designed to stabilize the plant, and the necessary and sufficient condition for the plant to be stabilized by the proposed controller is presented using the Nevanlinna-Pick interpolation theory. It is shown that the class of stabilization plants via the proposed controller in the paper is larger than that by the controller in reference. An example is also given to illustrate this fact.
文摘Web service applications are increasing tremendously in support of high-level businesses.There must be a need of better server load balancing mechanism for improving the performance of web services in business.Though many load balancing methods exist,there is still a need for sophisticated load bal-ancing mechanism for not letting the clients to get frustrated.In this work,the ser-ver with minimum response time and the server having less traffic volume were selected for the aimed server to process the forthcoming requests.The Servers are probed with adaptive control of time with two thresholds L and U to indicate the status of server load in terms of response time difference as low,medium and high load by the load balancing application.Fetching the real time responses of entire servers in the server farm is a key component of this intelligent Load balancing system.Many Load Balancing schemes are based on the graded thresholds,because the exact information about the networkflux is difficult to obtain.Using two thresholds L and U,it is possible to indicate the load on particular server as low,medium or high depending on the Maximum response time difference of the servers present in the server farm which is below L,between L and U or above U respectively.However,the existing works of load balancing in the server farm incorporatefixed time to measure real time response time,which in general are not optimal for all traffic conditions.Therefore,an algorithm based on Propor-tional Integration and Derivative neural network controller was designed with two thresholds for tuning the timing to probe the server for near optimal perfor-mance.The emulation results has shown a significant gain in the performance by tuning the threshold time.In addition to that,tuning algorithm is implemented in conjunction with Load Balancing scheme which does not tune thefixed time slots.
文摘Through a third⁃order mathematical model of grid⁃oriented LCL⁃type converters,this paper analyzes the complicated dynamic characteristics and resonance problems which may influence the system stability.To realize active damping for LCL filters and improve dynamic performance of current regulators,a state space current PI controller is proposed whose parameters can be tuned based on the polynomial equations approach.An extended state observer is integrated with the regulation scheme,where additional sensors are not necessary in contrast with conventional active damping strategies.Synchronous reference frame PLL(SRF⁃PLL)equipped with filter technology is proposed for grid voltage disturbance suppression.This method is then applied to establish a double⁃closed⁃loop power regulator that demonstrates improved performance compared with other controllers.The simulation results are displayed to illustrate the efficiency of the regulation methods.
基金Supported by the National Natural Science Foundation of China!( 19782 0 0 3 ) theChina Postdoctoral Science Foundation and
文摘In this paper, the nonlinear control of chaotic oscillations was investigated by using the input output linearization control method. The chaotic attitude of a kind of spacecraft was discussed. It is demonstrated that the input output linearization control law is the nonlinear version of the parametric open plus closed loop control law.
文摘This paper presents a novel design method of force rebalance control for the sense mode of micromachined vibratory gyroscopes.Specific theoretical deductions are performed to identify a precise linear model of the open loop system of the sense mode,which is crucial for the PI controller design.The frequency responses obtained by experimental tests agree well with those calculated with the theoretical model,indicating the accuracy of the theoretical analyses.Experimental results demonstrate that the bandwidth of the closed loop is extended to 94.8 Hz from 2.3 Hz in the open loop and the quadrature signal is suppressed by about 64 dBV in the closed loop system.The overshoot and stable time in the step response of the closed loop system are measured to be about 15% and 35 ms,respectively.The mode-splitting gyroscope with the closed loop controlled sense mode achieves a scale factor of 41.0 mV/deg/s with nonlinearity of 0.09% and asymmetry of 1%,and a bias instability of 4.0 °/h with angle random walk of 0.171 deg/h1/2.
基金Foundation item: Project(2009AA04Z143) supported by the National High Technology Research and Development Program of ChinaProject (E2011203004) supported by Natural Science Foundation of Hebei Province, ChinaProjects(2011BAF15B03, 2011BAF15B02) supported by the National Science Plan of China
文摘A high-precision shape detecting system of cold rolling strip is developed to meet industrial application, which mainly consists of the shape detecting roller, the collecting ring, the digital signal processing （DSP） shape signal processing board and the shape control model. Based on the shape detecting principle, the shape detecting roller is designed with a new integral structure for improving the precision of shape detecting and avoiding scratching strip surface. Based on the DSP technology, the DSP shape signal processing circuit board is designed and embedded in the shape detecting system for the reliability and stability of shape signal processing. The shape detecting system was successfully used in Angang 1 250 mm HC 6-high reversible cold rolling mill. The precision of shape detecting is 0.2 I and the shape deviation is controlled within 6 1 after the close loop shape control is input.
基金supported by the International S&T Cooperation Projects of China(2015DFR10510)the National Natural Science Foundation of China(61440048+1 种基金61562018)the Scientific Research Program of the Higher Education Institutions of Hainan Province(HNKY2014-04)
