The effects of ultrafine WC(WC_(UF),0.5μm) or W(1μm) and C(0.3μm)(W+C)_(UF) additives on the densification,microstructure and mechanical properties of coarse-grained cemented carbides were compared systematically.O...The effects of ultrafine WC(WC_(UF),0.5μm) or W(1μm) and C(0.3μm)(W+C)_(UF) additives on the densification,microstructure and mechanical properties of coarse-grained cemented carbides were compared systematically.Overall,the cemented carbides with WC_(UF)/(W+C)_(UF) additives are almost fully densification to be higher than 99%,and the average grain size is kept above 2.8μm.The WC_(UF) additive assists grains to(truncated)trigonal prism shape by two dimensional(2D) growth,whereas the(W+C)_(UF) additive assists grains to rounded shape by three dimensional(3D) growth,lowers WC contiguity and increases face-centered-cubic Co.The hardness and bending strength of(75WC_(C)-15WC_(UF))-10Co are 86.6 HRA and 2 272 MPa,respectively,both higher than those of(75WC_(C)-15(W+C)_(UF))-10Co,which could be ascribed to the enhanced densification and unblemished grains.However,the fracture toughness of the(75WC_(C)-15(W+C)_(UF))-10Co is 23.5 MPa·m^(1/2),higher than that of the(75WC_(C)-15WC_(UF))-10Co due to the uniform WC-Co structure and flexible binder phase.展开更多
Effects of Zirconium on the chemical component and size distribution of Ti-bearing inclusions, favored the grain refinement of the welding reduced, coarse-grained heat affected zone （CGHAZ） with enhanced impact toug...Effects of Zirconium on the chemical component and size distribution of Ti-bearing inclusions, favored the grain refinement of the welding reduced, coarse-grained heat affected zone （CGHAZ） with enhanced impact toughness in Ti-killed steels, which were examined based on experimental observations and thermodynamic calculations. It indicated that the chemical constituents of inclusions gradually varied from the TiO oxide to the Ti-O＋Zr-O compound oxide and a single phase of the ZrO2 oxide, as the Zr content increased from zero to 0.0100%. A trace of Zr （0.0030%-0.0080%, depending on the oxygen content in liquid steel） provided a large amount of nucleating core for Ti oxide because of the larger specific density of ZrO2 oxide, and produced a small size distribution of the inclusions favorable for acicular ferrite transformation with a high nucleation rate in the CGHAZ, and a high volume fraction of acicular ferrite was obtained in the CGHAZ, with enhanced impact toughness. Otherwise, a high content of Zr （-0.0100%） produced a single phase Zr02, which was impotent to nucleate acicular ferrite, and a microstructure composed of ferrite side plate and grain boundary ferrite developed in the CGHAZ. The experimental results were confirmed by thermodynamic calculations.展开更多
The austenite grain growth behavior in a simulated coarse-grained heat-affected zone during thermal cycling was investigated via in situ observation. Austenite grains nucleated at ferrite grain boundaries and then gre...The austenite grain growth behavior in a simulated coarse-grained heat-affected zone during thermal cycling was investigated via in situ observation. Austenite grains nucleated at ferrite grain boundaries and then grew in different directions through movement of grain boundaries into the ferrite phase. Subsequently, the adjacent austenite grains impinged against each other during the α→γtransformation. After the α→γ transformation, austenite grains coarsened via the coalescence of small grains and via boundary migration between grains. The growth process of austenite grains was a continuous process during heating, isothermal holding, and cooling in simulated thermal cycling. Abundant finely dispersed nanoscale TiN particles in a steel specimen containing 0.012wt% Ti effectively retarded the grain boundary migration, which resulted in refined austenite grains. When the Ti concentration in the steel was increased, the number of TiN particles de- creased and their size coarsened. The big particles were not effective in pinning the austenite grain boundary movement and resulted in coarse austenite grains.展开更多
Coarse-grained subaqueous fans are vital oil and gas exploration targets in the Bohai Bay basin,China.The insufficient understanding of their sedimentary processes,depositional patterns,and controlling factors restric...Coarse-grained subaqueous fans are vital oil and gas exploration targets in the Bohai Bay basin,China.The insufficient understanding of their sedimentary processes,depositional patterns,and controlling factors restricts efficient exploration and development.Coarse-grained subaqueous fans in the Yong′an area,Dongying Depression,are investigated in this study.These fans include nearshore subaqueous fans,and sublacustrine fans,and their sedimentary processes,depositional patterns and distribution characteristics are mainly controlled by tectonic activity and paleogeomorphology.Nearshore subaqueous fans developed near the boundary fault during the early–middle deposition stage due to strong tectonic activity and large topographic subsidence.Early sublacustrine fans developed at the front of the nearshore subaqueous fans in the area where the topography changed from gentle to steep along the source direction.While the topography was gentle,sublacustrine fans did not develop.During the late weak tectonic activity stage,late sublacustrine fans developed with multiple stages superimposed.Frequent fault activity and related earthquakes steepened the basin margin,and the boundary fault slopes were 25.9°–34°.During the early–middle deposition stage,hyperpycnal flows triggered by outburst floods developed.During the late deposition stage,with weak tectonic activity,seasonal floods triggered hyperpycnal flows,and hybrid event beds developed distally.展开更多
In this study,zircon U-Pb dating of volcanic rocks from the Zhongba ophiolite of the Yarlung Zangbo Suture Zone(YZSZ)in southern Xizang(Tibet)yielded an age of 247±3 Ma.According to whole rock geochemical and Sr-...In this study,zircon U-Pb dating of volcanic rocks from the Zhongba ophiolite of the Yarlung Zangbo Suture Zone(YZSZ)in southern Xizang(Tibet)yielded an age of 247±3 Ma.According to whole rock geochemical and Sr-NdPb isotopic data,the Early Triassic samples could be divided into two groups:Group 1 with P-MORB affinity,showing initial^(87)Sr/^(86)Sr ratios of 0.70253–0.70602,ε_(Nd)(t)values of 4.2–5.3,(^(206)Pb/^(204)Pb)_(t)ratios of 16.353–18.222,(^(207)Pb/^(204)Pb)_(t)ratios of 15.454–15.564,and(^(208)Pb/^(204)Pb)_(t)ratios of 35.665–38.136;Group 2 with OIB affinity,showing initial^(87)Sr/^(86)Sr ratios of 0.70249–0.70513,ε_(Nd)(t)values of 4.4–4.9,(^(206)Pb/^(204)Pb)_(t)ratios of 17.140–18.328,(^(207)Pb/^(204)Pb)_(t)ratios of 15.491–15.575,and(^(208)Pb/^(204)Pb)_(t)ratios of 36.051–38.247.Group 2 rocks formed by partial melting of the mantle source enriched by a former plume,and assimilated continental crustal material during melt ascension.The formation of Group 1 rocks corresponds to the mixing of OIB melts,with the same components as Group 2 and N-MORBs.The Zhongba Early Triassic rocks belong to the continental margin type ophiolite and formed in the continental–oceanic transition zone during the initial opening of the Neo-Tethys in southern Xizang(Tibet).展开更多
The infamous type Ⅳ failure within the fine-grained heat-affected zone (FGHAZ) in G115 steel weldments seriously threatens the safe operation of ultra-supercritical (USC) power plants.In this work,the traditional the...The infamous type Ⅳ failure within the fine-grained heat-affected zone (FGHAZ) in G115 steel weldments seriously threatens the safe operation of ultra-supercritical (USC) power plants.In this work,the traditional thermo-mechanical treatment was modified via the replacement of hot-rolling with cold rolling,i.e.,normalizing,cold rolling,and tempering (NCT),which was developed to improve the creep strength of the FGHAZ in G115 steel weldments.The NCT treatment effectively promoted the dissolution of preformed M_(23)C_(6)particles and relieved the boundary segregation of C and Cr during welding thermal cycling,which accelerated the dispersed reprecipitation of M_(23)C_(6) particles within the fresh reaustenitized grains during post-weld heat treatment.In addition,the precipitation of Cu-rich phases and MX particles was promoted evidently due to the deformation-induced dislocations.As a result,the interacting actions between precipitates,dislocations,and boundaries during creep were reinforced considerably.Following this strategy,the creep rupture life of the FGHAZ in G115 steel weldments can be prolonged by 18.6%,which can further push the application of G115 steel in USC power plants.展开更多
An observer-based adaptive backstepping boundary control is proposed for vibration control of flexible offshore riser systems with unknown nonlinear input dead zone and uncertain environmental disturbances.The control...An observer-based adaptive backstepping boundary control is proposed for vibration control of flexible offshore riser systems with unknown nonlinear input dead zone and uncertain environmental disturbances.The control algorithm can update the control law online through real-time data to make the controller adapt to the environment and improve the control precision.Specifically,based on the adaptive backstepping framework,virtual control laws and Lyapunov functions are designed for each subsystem.Three direction interference observers are designed to track the timevarying boundary disturbance.On this basis,the inverse of the dead zone and linear state transformation are used to compensate for the original system and eliminate the adverse effects of the dead zone.In addition,the stability of the closed-loop system is proven by Lyapunov stability theory.All the system states are bounded,and the vibration offset of the riser converges to a small area of the initial position.Finally,four examples of flexible marine risers are simulated in MATLAB to verify the effectiveness of the proposed controller.展开更多
AIM:To present the 1-year results of a prospective cohort study investigating the efficacy,potential mechanism,and safety of orthokeratology(ortho-k)with different back optic zone diameters(BOZD)for myopia control in ...AIM:To present the 1-year results of a prospective cohort study investigating the efficacy,potential mechanism,and safety of orthokeratology(ortho-k)with different back optic zone diameters(BOZD)for myopia control in children.METHODS:This randomized clinical study was performed between Dec.2020 and Dec.2021.Participants were randomly assigned to three groups wearing ortho-k:5 mm BOZD(5-MM group),5.5 mm BOZD(5.5-MM group),and 6 mm BOZD(6-MM group).The 1-year data were recorded,including axial length,relative peripheral refraction(RPR,measured by multispectral refractive topography,MRT),and visual quality.The contrast sensitivity(CS)was evaluated by CSV-1000 instrument with spatial frequencies of 3,6,12,and 18 cycles/degree(c/d);the corneal higher-order aberrations(HOAs)were measured by iTrace aberration analyzer.The one-way ANOVA was performed to assess the differences between the three groups.The correlation between the change in AL and RPR was calculated by Pearson’s correlation coefficient.RESULTS:The 1-year results of 20,21,and 21 subjects in the 5-MM,5.5-MM,and 6-MM groups,respectively,were presented.There were no statistical differences in baseline age,sex,or ocular parameters between the three groups(all P>0.05).At the 1-year visit,the 5-MM group had lower axial elongation than the 6-MM group(0.07±0.09 vs 0.18±0.11 mm,P=0.001).The 5-MM group had more myopic total RPR(TRPR,P=0.014),with RPR in the 15°–30°(RPR 15–30,P=0.015),30°–45°(RPR 30–45,P=0.011),temporal(RPR-T,P=0.008),and nasal area(RPR-N,P<0.001)than the 6-MM group.RPR 15–30 in the 5.5-MM group was more myopic than that in the 6-MM group(P=0.002),and RPR-N in the 5-MM group was more myopic than that in the 5.5-MM group(P<0.001).There were positive correlations between the axial elongation and the change in TRPR(r=0.756,P<0.001),RPR 15–30(r=0.364,P=0.004),RPR 30–45(r=0.306,P=0.016),and RPR-N(r=0.253,P=0.047).The CS decreased at 3 c/d(P<0.001),and the corneal HOAs increased in the 5-MM group(P=0.030).CONCLUSION:Ortho-k with 5 mm BOZD can control myopia progression more effectively.The mechanism may be associated with greater myopic shifts in RPR.展开更多
Based on the thermal simulation method,a systematical analysis was conducted on the effect of welding peak temperature and the cooling time that takes place from 800 to 500℃ on microstructure,precipitates,substructur...Based on the thermal simulation method,a systematical analysis was conducted on the effect of welding peak temperature and the cooling time that takes place from 800 to 500℃ on microstructure,precipitates,substructure and microhardness of the reheated coarse-grained heat-affected zone(CGHAZ)of G115 novel martensitic heat-resistant steel.As revealed from the results,the microstructure of un-altered CGHAZ(UACGHAZ)and supercritically CGHAZ(SCCGHAZ)was lath martensite,and structural heredity occurred.Intercritically reheated CGHAZ(IRCGHAZ)exhibited martensite and over-tempered martensite,and subcritical CGHAZ(SCGHAZ)displayed martensite and under-tempered martensite.The austenite in UACGHAZ and SCCGHAZ was transformed with the diffusion mechanism during the first thermal cycle,but with the non-diffusion mechanism during the second thermal cycle.For this reason,A_(c1) and A_(c3) during the second thermal cycle were significantly lower than those during the first thermal cycle,and A_(c1) and A_(c3) were reduced by nearly 14 and 44℃,respectively.Since the content and stability of the austenite alloy during the second thermal cycle of IRCGHAZ were lower than those during the first thermal cycle,M_(s) increased by nearly 30℃.There were considerable precipitates in the over-tempered region of IRCGHAZ,and the Laves phase was contained,which was not conducive to high-temperature creep property.Moreover,the dislocation density and the number of sub-grains in the region were lower,resulting in a sharp decrease in the microhardness,and it was the weak area in the reheated CGHAZ.展开更多
The Triassic was a crucial period in the tectonic evolution of the South China Block.Research on tectonic deformation during this period provides information on intracontinental orogenic mechanisms in South China.In t...The Triassic was a crucial period in the tectonic evolution of the South China Block.Research on tectonic deformation during this period provides information on intracontinental orogenic mechanisms in South China.In this study,alongside thermochronological analyses,we examine the macroscopic and microscopic structural features of the Rongxian ductile shear zone,located south of the Darongshan granite in the southeastern part of Guangxi Province,on the southern margin of South China.Sinistral shear is indicated by the characteristics of rotatedσ-type feldspar porphyroclasts,stretching lineations defined by elongated quartz grains and the orientations of quartz c-axes.LA-ICP-MS U-Pb dating of zircons from two samples of granitic mylonite and one of granite yielded ages of ca.256 Ma.Furthermore,two samples of granitic mylonite yield muscovite^(40)Ar/^(39)Ar plateau ages of 249-246 Ma.These results indicate that the Rongxian ductile shear zone resulted from Early Triassic deformation of the late Permian Darongshan granite.This deformation was likely related to the closure of the eastern Paleo-Tethys Ocean and the subsequent collision of the South China and Indochina blocks,during the early stage of the Indosinian orogeny.展开更多
Large earthquakes frequently occur along complex fault systems.Understanding seismic rupture and long-term fault evolution requires constraining the geometric and material properties of fault zone structures.We provid...Large earthquakes frequently occur along complex fault systems.Understanding seismic rupture and long-term fault evolution requires constraining the geometric and material properties of fault zone structures.We provide a comprehensive overview of recent advancements in seismological methods used to study fault zone structures,including seismic tomography,fault zone seismic wave analysis,and seismicity analysis.Observational conditions limit our current ability to fully characterize fault zones,for example,insufficient imaging resolution to discern small-scale anomalies,incomplete capture of crucial fault zone seismic waves,and limited precision in event location accuracy.Dense seismic arrays can overcome these limitations and enable more detailed investigations of fault zone structures.Moreover,we present new insights into the structure of the Anninghe-Xiaojiang fault zone in the southeastern margin of the Qinghai-Xizang Plateau based on data collected from a dense seismic array.We found that utilizing a dense seismic array can identify small-scale features within fault zones,aiding in the interpretation of fault zone geometry and material properties.展开更多
Urban-suburban-rural(U-S-R)zones exhibit distinctive transitional characteristics in interaction between human and nature.U-S-R transition zones(U-S-RTZ)are also highlighting the function diversity and landscape heter...Urban-suburban-rural(U-S-R)zones exhibit distinctive transitional characteristics in interaction between human and nature.U-S-R transition zones(U-S-RTZ)are also highlighting the function diversity and landscape heterogeneity across territorial spaces.As a super megacity in western China,Chengdu’s rapid urbanization has driven the evolution of U-S-R spaces,resulting in a sequential structure.To promote the high-quality spatial development of urban-rural region in a structured and efficient manner,it is essential to con-duct a scientific examination of the multidimensional interconnection within the U-S-RTZ framework.By proposing a novel identifica-tion method of U-S-RTZ and taking Chengdu,China as a case study,grounded in a blender of natural and humanistic factors,this study quantitatively delineated and explored the spatial evolutions of U-S-RTZ and stated the optimization orientation and sustainable devel-opment strategies of the production-living-ecological spaces along the U-S-R gradients.The results show that:1)it is suitable for the quantitative analysis of U-S-RTZ by established three-dimensional identification system in this study.2)In 1990-2020,the urban-sub-urban transition zones(U-STZ)in Chengdu have continuously undergone a substantial increase,and the scale of the suburban-rural transition zones(S-RTZ)has continued to expand slightly,while the space of rural-ecological transition zones(R-ETZ)has noticeably compressed.3)The landuse dynamics within U-S-RTZ has gradually increased in 1990-2020.The main direction of landuse transition was from farmland to construction land or woodlands,with the expansion of construction land being the most significant.4)R-ETZ primarily focus on ecological functions,and there is a trade-off relationship between the production-ecological function within the S-RTZ,and in the U-STZ,production-living composite functions are prioritized.This study emphasizes the importance of elastic planning and precise governance within the U-S-RTZ in a rapid urbanization region,particularly highlighting the role of suburbs as landscape corridors and service hubs in urban-rural integration.It elucidates to the practical implications for achieving high-quality development of integrated U-S-R territorial spaces.展开更多
Coastal zones are dynamic,rich environments,now densely populated,and increasingly challenged by human and climatechange pressures.Effective long-term integrated coastal zone planning is needed to ensure sustainable e...Coastal zones are dynamic,rich environments,now densely populated,and increasingly challenged by human and climatechange pressures.Effective long-term integrated coastal zone planning is needed to ensure sustainable environmental protection and economic development.In this study,we reviewed the history of coastal zone planning since its birth in the 1950s based on the literature retrieved from the Web of Science(Core Collection)from 2000–2023,then summarized the tools and spatial allocation methods commonly used in the planning process,and finally proposed potential solutions to the challenges faced.The results show that after decades of development,coastal zone planning has changed from a decentralized activity to a targeted and integrated one,with an increasing emphasis on the ecosystem approach and the use of multiple planning tools.Spatial analysis techniques and environmental modelling software have become increasingly popular.Linear programming and overlay analysis are common approaches when performing spatial optimization,but land-sea interactions and planning in the marine parts still lack in-depth analysis and practical experience.We are also aware that the challenges posed by the integration of administrative hierarchies,scoping and conservation objectives,stakeholder participation,consideration of social dimensions,and climate change are pervasive throughout the planning process.There is an urgent need to develop more flexible and accurate spatial modelling tools,as well as more efficient participatory methods,and to focus on the holistic nature of the land-sea system to create more resilient and sustainable coastal zones.展开更多
BACKGROUND Marginal zone lymphoma(MZL)is an indolent subtype of non-Hodgkin lymphoma(NHL),which is rare clinically with severe rashes as the initial symptom.CASE SUMMARY This study reports a case of MZL with generaliz...BACKGROUND Marginal zone lymphoma(MZL)is an indolent subtype of non-Hodgkin lymphoma(NHL),which is rare clinically with severe rashes as the initial symptom.CASE SUMMARY This study reports a case of MZL with generalized skin rashes accompanied by pruritus and purulent discharge.First-line treatment with rituximab combined with zanubrutinib had poor effects.However,after switching to obinutuzumab combined with zanubrutinib,the case was alleviated,and the rashes disappeared.CONCLUSION For patients with advanced stage MZL not benefiting from type I anti-CD20 monoclonal antibody(mAb)combination therapy,switching to a type II anti-CD20 mAb combination regimen may be considered.This approach may provide a new perspective in the treatment of MZL.展开更多
A fault accommodation zone is a type of structure that is defined as regulating displacement and strain between faults structure.Increasing numbers of fault accommodation zones are being identified in graben basins,in...A fault accommodation zone is a type of structure that is defined as regulating displacement and strain between faults structure.Increasing numbers of fault accommodation zones are being identified in graben basins,indicating the potential exploration target and petroleum accumulation areas.This study aims to analyze the formation mechanism and development of fault accommodation zones under combined stress by a numerical simulation method considering geomechanical modeling.Using three-dimensional(3-D)seismic interpretation and fractal dimension method,exampled with the Dongxin fault zone,the fault activity and fault combination pattern were conducted to quantitatively characterize the activity difference in fault accommodation zones.Combined with mechanical experiment test,a geomehcanical model was established for fault accommodation zones in a graben basin.Integrating the paleostress numerical simulations and structural physical simulation experiment,the developmental characteristics and genetic mechanism of fault accommodation zones were summarized.Influenced by multi movements and combined stresses,three significant tectonic evolution stages of the Dongxing Fault Zone(DXFZ)were distinguished:During the E_(s)^(3)sedimentary period,the large difference in the stress,strain,and rupture distribution in various faults were significant,and this stage was the key generation period for the prototype of the DXFZ,including the FAZ between large-scale faults.During the E_(s)^(2)sedimentary period,the EW-trending symmetric with opposite dipping normal faults and the NE-SW trending faults with large scale were furtherly developed.The junction area of two secondary normal faults were prone to be ruptured,performing significant period for inheriting and developing characteristics of fault accommodation zones.During the Es1 sedimentary period,the high-order faults in the DXFZ exhibited the obvious fault depressions and strike-slip activity,and the fault accommodation zones were furtherly inherited and developed.This stage was the molded and formative period of the FAZ,the low-order faults,and the depression in the DXFZ.展开更多
In the internal parts of the Zagros collision zone, several deformation phases have been superimposed. The early deformation phase caused the development of a penetrative foliation. The late-stage deformation phase wa...In the internal parts of the Zagros collision zone, several deformation phases have been superimposed. The early deformation phase caused the development of a penetrative foliation. The late-stage deformation phase was preferentially accommodated within shear zones and caused the generation of shear bands, implying a non-coaxial component of deformation, the end of this stage deformation was marked by the development of kink-bands. In the vicinity of Zagros suture zone, the kink angle increased from 40° to 60°, and the kink-bands was converted to chevron folds. In this region, the external(α) and internal(β) angular ratio is α/β ≠ 1 and kink angle increased, and deformation occurred with 10% to 30% volume loss. Farther from the suture zone in the east, α/β = 1;and total volume was constant or increased by 5% to 10%. Kink-bands kinematic analysis in the study area revealed this structures were sensitive to deformation conditions and components such that, with decreasing distance to the Zagros suture zone, shearing and rotation increased, a high kinematic vorticity dominated, and volume loss occurred during deformation.展开更多
Optical vortices generated by the conventional vortex lens are usually disturbed by the undesired higher-order foci,which may lead to additional artifacts and thus degrade the contrast sensitivity. In this work, we pr...Optical vortices generated by the conventional vortex lens are usually disturbed by the undesired higher-order foci,which may lead to additional artifacts and thus degrade the contrast sensitivity. In this work, we propose an efficient methodology to combine the merit of elliptical reflective zone plates(ERZPs) and the advantage of spiral zone plates(SZPs) in establishing a specific single optical element, termed elliptical reflective annulus quadrangle-element coded spiral zone plates(ERAQSZPs) to generate single-focus phase singularity. Differing from the abrupt reflectance of the ERZPs, a series of randomly distributed nanometer apertures are adopted to realize the sinusoidal reflectance. Typically, according to our physical design, the ERAQSZPs are fabricated on a bulk substrate;therefore, the new idea can significantly reduce the difficulty in the fabrication process. Based on the Kirchhoff diffraction theory and convolution theorem, the focusing performance of ERAQSZPs is calculated. The results reveal that apart from the capability of generating optical vortices,ERAQSZPs can also integrate the function of focusing, energy selection, higher-order foci elimination, as well as high spectral resolution together. In addition, the focusing properties can be further improved by appropriately adjusting the parameters, such as zone number and the size of the consisted primitives. These findings are expected to direct a new direction toward improving the performance of optical capture, x-ray fluorescence spectra, and forbidden transition.展开更多
Cultivation of pollinator-dependent crops has expanded globally, increasing our reliance on insect pollination. This essential ecosystem service is provided by a wide range of managed and wild pollinators whose abunda...Cultivation of pollinator-dependent crops has expanded globally, increasing our reliance on insect pollination. This essential ecosystem service is provided by a wide range of managed and wild pollinators whose abundance and diversity are thought to be in decline, threatening sustainable food production. In Cameroon, several studies on pollinator-dependent crops carried out in different agro-ecological zones (AEZ) have been published in national and international journals, in order to present the importance and impact of flowering insects on fruit and seed yields of plant species. We proposed to produce a review article highlighting the different flowering insects and their importance for different plants according to AEZ, without however focusing on the quality of the journal (predator or non-predator) and how the different insects were identified (scientific names given in the publications). Thus, from 1997 to 2020, we collected 116 published papers from which only 26 were kept for this review. The results show that Hymenoptera, including the Apidae, followed by Megachilidae, are the most excellent pollinators of plant species in Cameroon, and they are present in different agro-ecological zones. The majority of publications focused on bees, particularly the honeybee Apis mellifera.展开更多
It is acknowledged today within the scientific community that two types of actions must be considered to limit global warming: mitigation actions by reducing GHG emissions, to contain the rate of global warming, and a...It is acknowledged today within the scientific community that two types of actions must be considered to limit global warming: mitigation actions by reducing GHG emissions, to contain the rate of global warming, and adaptation actions to adapt societies to Climate Change, to limit losses and damages [1] [2]. As far as adaptation actions are concerned, numerical simulation, due to its results, its costs which require less investment than tests carried out on complex mechanical structures, and its implementation facilities, appears to be a major step in the design and prediction of complex mechanical systems. However, despite the quality of the results obtained, biases and inaccuracies related to the structure of the models do exist. Therefore, there is a need to validate the results of this SARIMA-LSTM-digital learning model adjusted by a matching approach, “calculating-test”, in order to assess the quality of the results and the performance of the model. The methodology consists of exploiting two climatic databases (temperature and precipitation), one of which is in-situ and the other spatial, all derived from grid points. Data from the dot grids are processed and stored in specific formats and, through machine learning approaches, complex mathematical equations are worked out and interconnections within the climate system established. Through this mathematical approach, it is possible to predict the future climate of the Sudano-Sahelian zone of Cameroon and to propose adaptation strategies.展开更多
The Sonid Zuoqi ductile detachment zone is located at the southeastern margin of the Central Asian orogenic belt(CAOB),striking EW and dipping to the S.The major rock type of the Sonid Zuoqi ductile detachment zone is...The Sonid Zuoqi ductile detachment zone is located at the southeastern margin of the Central Asian orogenic belt(CAOB),striking EW and dipping to the S.The major rock type of the Sonid Zuoqi ductile detachment zone is mylonite derived from granite.The sequence of mylonite features is:(1)S and C foliations of mylonite,and(2)extensional crenulation cleavage(ecc)or C′and the kinematic vorticity(Wk)value changed from 0.70 to 0.95 and from 0.37 to 0.69,respectively;the strain type of the mylonites within the Sonid Zuoqi ductile detachment zone is compressional to planar strain.The strong deformation mylonite and Halatu plutons yielded a zircon U-Pb age of 244 Ma and a zircon(U-Th)/He age of 214 Ma,respectively.Based on the strain and kinematic vorticity analysis,together with the zircon U-Pb and zircon(U-Th)/He ages and the regional tectonic background,the study area experienced three stage evolution:tangential simpleshear(244 Ma),simple-shear-dominated general shear represented by upper crustal extension(224 Ma)and pure-shear-dominated general shear represented by the Halatu pluton doming(214 Ma),which constrained the early Mesozoic NE-SW crustal extension at the southeastern margin of the CAOB.This NE-SW extension probably originated from the postorogenic extensional collapse of the CAOB,subsequent exhumation being controlled by the far afield effects of the closure of the Mongol-Okhotsk belt.展开更多
基金Funded by the Technology Innovation Leading Program of Shaanxi(No.2022QFY08-02)。
文摘The effects of ultrafine WC(WC_(UF),0.5μm) or W(1μm) and C(0.3μm)(W+C)_(UF) additives on the densification,microstructure and mechanical properties of coarse-grained cemented carbides were compared systematically.Overall,the cemented carbides with WC_(UF)/(W+C)_(UF) additives are almost fully densification to be higher than 99%,and the average grain size is kept above 2.8μm.The WC_(UF) additive assists grains to(truncated)trigonal prism shape by two dimensional(2D) growth,whereas the(W+C)_(UF) additive assists grains to rounded shape by three dimensional(3D) growth,lowers WC contiguity and increases face-centered-cubic Co.The hardness and bending strength of(75WC_(C)-15WC_(UF))-10Co are 86.6 HRA and 2 272 MPa,respectively,both higher than those of(75WC_(C)-15(W+C)_(UF))-10Co,which could be ascribed to the enhanced densification and unblemished grains.However,the fracture toughness of the(75WC_(C)-15(W+C)_(UF))-10Co is 23.5 MPa·m^(1/2),higher than that of the(75WC_(C)-15WC_(UF))-10Co due to the uniform WC-Co structure and flexible binder phase.
文摘Effects of Zirconium on the chemical component and size distribution of Ti-bearing inclusions, favored the grain refinement of the welding reduced, coarse-grained heat affected zone （CGHAZ） with enhanced impact toughness in Ti-killed steels, which were examined based on experimental observations and thermodynamic calculations. It indicated that the chemical constituents of inclusions gradually varied from the TiO oxide to the Ti-O＋Zr-O compound oxide and a single phase of the ZrO2 oxide, as the Zr content increased from zero to 0.0100%. A trace of Zr （0.0030%-0.0080%, depending on the oxygen content in liquid steel） provided a large amount of nucleating core for Ti oxide because of the larger specific density of ZrO2 oxide, and produced a small size distribution of the inclusions favorable for acicular ferrite transformation with a high nucleation rate in the CGHAZ, and a high volume fraction of acicular ferrite was obtained in the CGHAZ, with enhanced impact toughness. Otherwise, a high content of Zr （-0.0100%） produced a single phase Zr02, which was impotent to nucleate acicular ferrite, and a microstructure composed of ferrite side plate and grain boundary ferrite developed in the CGHAZ. The experimental results were confirmed by thermodynamic calculations.
基金financially supported by the Postdoctoral Science Foundation of China (No. 2014M550415)the National Natural Science Foundation of China (No. 50734004)
文摘The austenite grain growth behavior in a simulated coarse-grained heat-affected zone during thermal cycling was investigated via in situ observation. Austenite grains nucleated at ferrite grain boundaries and then grew in different directions through movement of grain boundaries into the ferrite phase. Subsequently, the adjacent austenite grains impinged against each other during the α→γtransformation. After the α→γ transformation, austenite grains coarsened via the coalescence of small grains and via boundary migration between grains. The growth process of austenite grains was a continuous process during heating, isothermal holding, and cooling in simulated thermal cycling. Abundant finely dispersed nanoscale TiN particles in a steel specimen containing 0.012wt% Ti effectively retarded the grain boundary migration, which resulted in refined austenite grains. When the Ti concentration in the steel was increased, the number of TiN particles de- creased and their size coarsened. The big particles were not effective in pinning the austenite grain boundary movement and resulted in coarse austenite grains.
基金supported by the National Science Foundation of China(Grant Nos.41972099,4217020246)the National Science and Technology Major of China(Grant Nos.2017ZX05009-002,2017ZX05072-002)。
文摘Coarse-grained subaqueous fans are vital oil and gas exploration targets in the Bohai Bay basin,China.The insufficient understanding of their sedimentary processes,depositional patterns,and controlling factors restricts efficient exploration and development.Coarse-grained subaqueous fans in the Yong′an area,Dongying Depression,are investigated in this study.These fans include nearshore subaqueous fans,and sublacustrine fans,and their sedimentary processes,depositional patterns and distribution characteristics are mainly controlled by tectonic activity and paleogeomorphology.Nearshore subaqueous fans developed near the boundary fault during the early–middle deposition stage due to strong tectonic activity and large topographic subsidence.Early sublacustrine fans developed at the front of the nearshore subaqueous fans in the area where the topography changed from gentle to steep along the source direction.While the topography was gentle,sublacustrine fans did not develop.During the late weak tectonic activity stage,late sublacustrine fans developed with multiple stages superimposed.Frequent fault activity and related earthquakes steepened the basin margin,and the boundary fault slopes were 25.9°–34°.During the early–middle deposition stage,hyperpycnal flows triggered by outburst floods developed.During the late deposition stage,with weak tectonic activity,seasonal floods triggered hyperpycnal flows,and hybrid event beds developed distally.
基金the National Natural Science Foundation of China(Grant Nos.91955206,41603038)Second Tibetan Plateau Scientific Expedition and Research program(Grant No.2019QZKK0803)+2 种基金Scientific Research Foundation for Advanced ScholarsWest Yunnan University of Applied Sciences(Grant No.2022RCKY0004)Yunnan Fundamental Research Projects(Grant No.202301AT070012).
文摘In this study,zircon U-Pb dating of volcanic rocks from the Zhongba ophiolite of the Yarlung Zangbo Suture Zone(YZSZ)in southern Xizang(Tibet)yielded an age of 247±3 Ma.According to whole rock geochemical and Sr-NdPb isotopic data,the Early Triassic samples could be divided into two groups:Group 1 with P-MORB affinity,showing initial^(87)Sr/^(86)Sr ratios of 0.70253–0.70602,ε_(Nd)(t)values of 4.2–5.3,(^(206)Pb/^(204)Pb)_(t)ratios of 16.353–18.222,(^(207)Pb/^(204)Pb)_(t)ratios of 15.454–15.564,and(^(208)Pb/^(204)Pb)_(t)ratios of 35.665–38.136;Group 2 with OIB affinity,showing initial^(87)Sr/^(86)Sr ratios of 0.70249–0.70513,ε_(Nd)(t)values of 4.4–4.9,(^(206)Pb/^(204)Pb)_(t)ratios of 17.140–18.328,(^(207)Pb/^(204)Pb)_(t)ratios of 15.491–15.575,and(^(208)Pb/^(204)Pb)_(t)ratios of 36.051–38.247.Group 2 rocks formed by partial melting of the mantle source enriched by a former plume,and assimilated continental crustal material during melt ascension.The formation of Group 1 rocks corresponds to the mixing of OIB melts,with the same components as Group 2 and N-MORBs.The Zhongba Early Triassic rocks belong to the continental margin type ophiolite and formed in the continental–oceanic transition zone during the initial opening of the Neo-Tethys in southern Xizang(Tibet).
基金financially supported by the National Key R&D Program of China(No.2022YFB3705300)the National Natural Science Foundation of China(Nos.U1960204 and 51974199)the Postdoctoral Fellowship Program of CPSF(No.GZB20230515)。
文摘The infamous type Ⅳ failure within the fine-grained heat-affected zone (FGHAZ) in G115 steel weldments seriously threatens the safe operation of ultra-supercritical (USC) power plants.In this work,the traditional thermo-mechanical treatment was modified via the replacement of hot-rolling with cold rolling,i.e.,normalizing,cold rolling,and tempering (NCT),which was developed to improve the creep strength of the FGHAZ in G115 steel weldments.The NCT treatment effectively promoted the dissolution of preformed M_(23)C_(6)particles and relieved the boundary segregation of C and Cr during welding thermal cycling,which accelerated the dispersed reprecipitation of M_(23)C_(6) particles within the fresh reaustenitized grains during post-weld heat treatment.In addition,the precipitation of Cu-rich phases and MX particles was promoted evidently due to the deformation-induced dislocations.As a result,the interacting actions between precipitates,dislocations,and boundaries during creep were reinforced considerably.Following this strategy,the creep rupture life of the FGHAZ in G115 steel weldments can be prolonged by 18.6%,which can further push the application of G115 steel in USC power plants.
基金financially supported by the Sichuan Science and Technology Program(Grant No.2023NSFSC1980)。
文摘An observer-based adaptive backstepping boundary control is proposed for vibration control of flexible offshore riser systems with unknown nonlinear input dead zone and uncertain environmental disturbances.The control algorithm can update the control law online through real-time data to make the controller adapt to the environment and improve the control precision.Specifically,based on the adaptive backstepping framework,virtual control laws and Lyapunov functions are designed for each subsystem.Three direction interference observers are designed to track the timevarying boundary disturbance.On this basis,the inverse of the dead zone and linear state transformation are used to compensate for the original system and eliminate the adverse effects of the dead zone.In addition,the stability of the closed-loop system is proven by Lyapunov stability theory.All the system states are bounded,and the vibration offset of the riser converges to a small area of the initial position.Finally,four examples of flexible marine risers are simulated in MATLAB to verify the effectiveness of the proposed controller.
基金Supported by Education Department Foundation of Sichuan Province(No.15ZA0262).
文摘AIM:To present the 1-year results of a prospective cohort study investigating the efficacy,potential mechanism,and safety of orthokeratology(ortho-k)with different back optic zone diameters(BOZD)for myopia control in children.METHODS:This randomized clinical study was performed between Dec.2020 and Dec.2021.Participants were randomly assigned to three groups wearing ortho-k:5 mm BOZD(5-MM group),5.5 mm BOZD(5.5-MM group),and 6 mm BOZD(6-MM group).The 1-year data were recorded,including axial length,relative peripheral refraction(RPR,measured by multispectral refractive topography,MRT),and visual quality.The contrast sensitivity(CS)was evaluated by CSV-1000 instrument with spatial frequencies of 3,6,12,and 18 cycles/degree(c/d);the corneal higher-order aberrations(HOAs)were measured by iTrace aberration analyzer.The one-way ANOVA was performed to assess the differences between the three groups.The correlation between the change in AL and RPR was calculated by Pearson’s correlation coefficient.RESULTS:The 1-year results of 20,21,and 21 subjects in the 5-MM,5.5-MM,and 6-MM groups,respectively,were presented.There were no statistical differences in baseline age,sex,or ocular parameters between the three groups(all P>0.05).At the 1-year visit,the 5-MM group had lower axial elongation than the 6-MM group(0.07±0.09 vs 0.18±0.11 mm,P=0.001).The 5-MM group had more myopic total RPR(TRPR,P=0.014),with RPR in the 15°–30°(RPR 15–30,P=0.015),30°–45°(RPR 30–45,P=0.011),temporal(RPR-T,P=0.008),and nasal area(RPR-N,P<0.001)than the 6-MM group.RPR 15–30 in the 5.5-MM group was more myopic than that in the 6-MM group(P=0.002),and RPR-N in the 5-MM group was more myopic than that in the 5.5-MM group(P<0.001).There were positive correlations between the axial elongation and the change in TRPR(r=0.756,P<0.001),RPR 15–30(r=0.364,P=0.004),RPR 30–45(r=0.306,P=0.016),and RPR-N(r=0.253,P=0.047).The CS decreased at 3 c/d(P<0.001),and the corneal HOAs increased in the 5-MM group(P=0.030).CONCLUSION:Ortho-k with 5 mm BOZD can control myopia progression more effectively.The mechanism may be associated with greater myopic shifts in RPR.
基金We would like to acknowledge the support of National Key R&D Program of China(No.2017YFB0305202)Inner Mongolia Natural Science Foundation(No.2016MS0510)Inner Mongolia Natural Science Foundation(No.2020MS05046).
文摘Based on the thermal simulation method,a systematical analysis was conducted on the effect of welding peak temperature and the cooling time that takes place from 800 to 500℃ on microstructure,precipitates,substructure and microhardness of the reheated coarse-grained heat-affected zone(CGHAZ)of G115 novel martensitic heat-resistant steel.As revealed from the results,the microstructure of un-altered CGHAZ(UACGHAZ)and supercritically CGHAZ(SCCGHAZ)was lath martensite,and structural heredity occurred.Intercritically reheated CGHAZ(IRCGHAZ)exhibited martensite and over-tempered martensite,and subcritical CGHAZ(SCGHAZ)displayed martensite and under-tempered martensite.The austenite in UACGHAZ and SCCGHAZ was transformed with the diffusion mechanism during the first thermal cycle,but with the non-diffusion mechanism during the second thermal cycle.For this reason,A_(c1) and A_(c3) during the second thermal cycle were significantly lower than those during the first thermal cycle,and A_(c1) and A_(c3) were reduced by nearly 14 and 44℃,respectively.Since the content and stability of the austenite alloy during the second thermal cycle of IRCGHAZ were lower than those during the first thermal cycle,M_(s) increased by nearly 30℃.There were considerable precipitates in the over-tempered region of IRCGHAZ,and the Laves phase was contained,which was not conducive to high-temperature creep property.Moreover,the dislocation density and the number of sub-grains in the region were lower,resulting in a sharp decrease in the microhardness,and it was the weak area in the reheated CGHAZ.
基金supported by the National Natural Science Foundation of China(Grant Nos.42262026,42072259).
文摘The Triassic was a crucial period in the tectonic evolution of the South China Block.Research on tectonic deformation during this period provides information on intracontinental orogenic mechanisms in South China.In this study,alongside thermochronological analyses,we examine the macroscopic and microscopic structural features of the Rongxian ductile shear zone,located south of the Darongshan granite in the southeastern part of Guangxi Province,on the southern margin of South China.Sinistral shear is indicated by the characteristics of rotatedσ-type feldspar porphyroclasts,stretching lineations defined by elongated quartz grains and the orientations of quartz c-axes.LA-ICP-MS U-Pb dating of zircons from two samples of granitic mylonite and one of granite yielded ages of ca.256 Ma.Furthermore,two samples of granitic mylonite yield muscovite^(40)Ar/^(39)Ar plateau ages of 249-246 Ma.These results indicate that the Rongxian ductile shear zone resulted from Early Triassic deformation of the late Permian Darongshan granite.This deformation was likely related to the closure of the eastern Paleo-Tethys Ocean and the subsequent collision of the South China and Indochina blocks,during the early stage of the Indosinian orogeny.
基金supported by the National Key R&D Program of China(No.2022YFF0800601)the National Natural Science Foundation of China(No.U2039204)the Special Fund of the Institute of Geophysics,China Earthquake Administration(No.DQJB23B22).
文摘Large earthquakes frequently occur along complex fault systems.Understanding seismic rupture and long-term fault evolution requires constraining the geometric and material properties of fault zone structures.We provide a comprehensive overview of recent advancements in seismological methods used to study fault zone structures,including seismic tomography,fault zone seismic wave analysis,and seismicity analysis.Observational conditions limit our current ability to fully characterize fault zones,for example,insufficient imaging resolution to discern small-scale anomalies,incomplete capture of crucial fault zone seismic waves,and limited precision in event location accuracy.Dense seismic arrays can overcome these limitations and enable more detailed investigations of fault zone structures.Moreover,we present new insights into the structure of the Anninghe-Xiaojiang fault zone in the southeastern margin of the Qinghai-Xizang Plateau based on data collected from a dense seismic array.We found that utilizing a dense seismic array can identify small-scale features within fault zones,aiding in the interpretation of fault zone geometry and material properties.
基金Under the auspices of National Natural Science Foundation of China(No.41930651)Sichuan Science and Technology Program(No.2023NSFSC1979)。
文摘Urban-suburban-rural(U-S-R)zones exhibit distinctive transitional characteristics in interaction between human and nature.U-S-R transition zones(U-S-RTZ)are also highlighting the function diversity and landscape heterogeneity across territorial spaces.As a super megacity in western China,Chengdu’s rapid urbanization has driven the evolution of U-S-R spaces,resulting in a sequential structure.To promote the high-quality spatial development of urban-rural region in a structured and efficient manner,it is essential to con-duct a scientific examination of the multidimensional interconnection within the U-S-RTZ framework.By proposing a novel identifica-tion method of U-S-RTZ and taking Chengdu,China as a case study,grounded in a blender of natural and humanistic factors,this study quantitatively delineated and explored the spatial evolutions of U-S-RTZ and stated the optimization orientation and sustainable devel-opment strategies of the production-living-ecological spaces along the U-S-R gradients.The results show that:1)it is suitable for the quantitative analysis of U-S-RTZ by established three-dimensional identification system in this study.2)In 1990-2020,the urban-sub-urban transition zones(U-STZ)in Chengdu have continuously undergone a substantial increase,and the scale of the suburban-rural transition zones(S-RTZ)has continued to expand slightly,while the space of rural-ecological transition zones(R-ETZ)has noticeably compressed.3)The landuse dynamics within U-S-RTZ has gradually increased in 1990-2020.The main direction of landuse transition was from farmland to construction land or woodlands,with the expansion of construction land being the most significant.4)R-ETZ primarily focus on ecological functions,and there is a trade-off relationship between the production-ecological function within the S-RTZ,and in the U-STZ,production-living composite functions are prioritized.This study emphasizes the importance of elastic planning and precise governance within the U-S-RTZ in a rapid urbanization region,particularly highlighting the role of suburbs as landscape corridors and service hubs in urban-rural integration.It elucidates to the practical implications for achieving high-quality development of integrated U-S-R territorial spaces.
基金Under the auspices of National Key R&D Plan (No.2022YFB3903604)the Youth Innovation Promotion Association of Chinese Academy of Sciences (No.2023060)Key Project of Innovation LREIS (No.KPI001)。
文摘Coastal zones are dynamic,rich environments,now densely populated,and increasingly challenged by human and climatechange pressures.Effective long-term integrated coastal zone planning is needed to ensure sustainable environmental protection and economic development.In this study,we reviewed the history of coastal zone planning since its birth in the 1950s based on the literature retrieved from the Web of Science(Core Collection)from 2000–2023,then summarized the tools and spatial allocation methods commonly used in the planning process,and finally proposed potential solutions to the challenges faced.The results show that after decades of development,coastal zone planning has changed from a decentralized activity to a targeted and integrated one,with an increasing emphasis on the ecosystem approach and the use of multiple planning tools.Spatial analysis techniques and environmental modelling software have become increasingly popular.Linear programming and overlay analysis are common approaches when performing spatial optimization,but land-sea interactions and planning in the marine parts still lack in-depth analysis and practical experience.We are also aware that the challenges posed by the integration of administrative hierarchies,scoping and conservation objectives,stakeholder participation,consideration of social dimensions,and climate change are pervasive throughout the planning process.There is an urgent need to develop more flexible and accurate spatial modelling tools,as well as more efficient participatory methods,and to focus on the holistic nature of the land-sea system to create more resilient and sustainable coastal zones.
文摘BACKGROUND Marginal zone lymphoma(MZL)is an indolent subtype of non-Hodgkin lymphoma(NHL),which is rare clinically with severe rashes as the initial symptom.CASE SUMMARY This study reports a case of MZL with generalized skin rashes accompanied by pruritus and purulent discharge.First-line treatment with rituximab combined with zanubrutinib had poor effects.However,after switching to obinutuzumab combined with zanubrutinib,the case was alleviated,and the rashes disappeared.CONCLUSION For patients with advanced stage MZL not benefiting from type I anti-CD20 monoclonal antibody(mAb)combination therapy,switching to a type II anti-CD20 mAb combination regimen may be considered.This approach may provide a new perspective in the treatment of MZL.
基金This research was supported by the Major Scientific and Technological Projects of CNPC under grant ZD2019-183-006the National Natural Science Foundation of China(42072234).The authors would like to appreciate all the people,who supported the data,testing,and analyses.Many thanks to the anonymous reviewers,whose comments improve the quality of our manuscript.
文摘A fault accommodation zone is a type of structure that is defined as regulating displacement and strain between faults structure.Increasing numbers of fault accommodation zones are being identified in graben basins,indicating the potential exploration target and petroleum accumulation areas.This study aims to analyze the formation mechanism and development of fault accommodation zones under combined stress by a numerical simulation method considering geomechanical modeling.Using three-dimensional(3-D)seismic interpretation and fractal dimension method,exampled with the Dongxin fault zone,the fault activity and fault combination pattern were conducted to quantitatively characterize the activity difference in fault accommodation zones.Combined with mechanical experiment test,a geomehcanical model was established for fault accommodation zones in a graben basin.Integrating the paleostress numerical simulations and structural physical simulation experiment,the developmental characteristics and genetic mechanism of fault accommodation zones were summarized.Influenced by multi movements and combined stresses,three significant tectonic evolution stages of the Dongxing Fault Zone(DXFZ)were distinguished:During the E_(s)^(3)sedimentary period,the large difference in the stress,strain,and rupture distribution in various faults were significant,and this stage was the key generation period for the prototype of the DXFZ,including the FAZ between large-scale faults.During the E_(s)^(2)sedimentary period,the EW-trending symmetric with opposite dipping normal faults and the NE-SW trending faults with large scale were furtherly developed.The junction area of two secondary normal faults were prone to be ruptured,performing significant period for inheriting and developing characteristics of fault accommodation zones.During the Es1 sedimentary period,the high-order faults in the DXFZ exhibited the obvious fault depressions and strike-slip activity,and the fault accommodation zones were furtherly inherited and developed.This stage was the molded and formative period of the FAZ,the low-order faults,and the depression in the DXFZ.
文摘In the internal parts of the Zagros collision zone, several deformation phases have been superimposed. The early deformation phase caused the development of a penetrative foliation. The late-stage deformation phase was preferentially accommodated within shear zones and caused the generation of shear bands, implying a non-coaxial component of deformation, the end of this stage deformation was marked by the development of kink-bands. In the vicinity of Zagros suture zone, the kink angle increased from 40° to 60°, and the kink-bands was converted to chevron folds. In this region, the external(α) and internal(β) angular ratio is α/β ≠ 1 and kink angle increased, and deformation occurred with 10% to 30% volume loss. Farther from the suture zone in the east, α/β = 1;and total volume was constant or increased by 5% to 10%. Kink-bands kinematic analysis in the study area revealed this structures were sensitive to deformation conditions and components such that, with decreasing distance to the Zagros suture zone, shearing and rotation increased, a high kinematic vorticity dominated, and volume loss occurred during deformation.
基金Project supported by the National Natural Science Foundation of China (Grant Nos.12174350,12275253,and 12275250)the Program of Science and Technology on Plasma Physics Laboratory,China Academy of Engineering Physics (Grant No.6142A04200107)the National Natural Science Foundation,Youth Fund (Grant No.12105268)。
文摘Optical vortices generated by the conventional vortex lens are usually disturbed by the undesired higher-order foci,which may lead to additional artifacts and thus degrade the contrast sensitivity. In this work, we propose an efficient methodology to combine the merit of elliptical reflective zone plates(ERZPs) and the advantage of spiral zone plates(SZPs) in establishing a specific single optical element, termed elliptical reflective annulus quadrangle-element coded spiral zone plates(ERAQSZPs) to generate single-focus phase singularity. Differing from the abrupt reflectance of the ERZPs, a series of randomly distributed nanometer apertures are adopted to realize the sinusoidal reflectance. Typically, according to our physical design, the ERAQSZPs are fabricated on a bulk substrate;therefore, the new idea can significantly reduce the difficulty in the fabrication process. Based on the Kirchhoff diffraction theory and convolution theorem, the focusing performance of ERAQSZPs is calculated. The results reveal that apart from the capability of generating optical vortices,ERAQSZPs can also integrate the function of focusing, energy selection, higher-order foci elimination, as well as high spectral resolution together. In addition, the focusing properties can be further improved by appropriately adjusting the parameters, such as zone number and the size of the consisted primitives. These findings are expected to direct a new direction toward improving the performance of optical capture, x-ray fluorescence spectra, and forbidden transition.
文摘Cultivation of pollinator-dependent crops has expanded globally, increasing our reliance on insect pollination. This essential ecosystem service is provided by a wide range of managed and wild pollinators whose abundance and diversity are thought to be in decline, threatening sustainable food production. In Cameroon, several studies on pollinator-dependent crops carried out in different agro-ecological zones (AEZ) have been published in national and international journals, in order to present the importance and impact of flowering insects on fruit and seed yields of plant species. We proposed to produce a review article highlighting the different flowering insects and their importance for different plants according to AEZ, without however focusing on the quality of the journal (predator or non-predator) and how the different insects were identified (scientific names given in the publications). Thus, from 1997 to 2020, we collected 116 published papers from which only 26 were kept for this review. The results show that Hymenoptera, including the Apidae, followed by Megachilidae, are the most excellent pollinators of plant species in Cameroon, and they are present in different agro-ecological zones. The majority of publications focused on bees, particularly the honeybee Apis mellifera.
文摘It is acknowledged today within the scientific community that two types of actions must be considered to limit global warming: mitigation actions by reducing GHG emissions, to contain the rate of global warming, and adaptation actions to adapt societies to Climate Change, to limit losses and damages [1] [2]. As far as adaptation actions are concerned, numerical simulation, due to its results, its costs which require less investment than tests carried out on complex mechanical structures, and its implementation facilities, appears to be a major step in the design and prediction of complex mechanical systems. However, despite the quality of the results obtained, biases and inaccuracies related to the structure of the models do exist. Therefore, there is a need to validate the results of this SARIMA-LSTM-digital learning model adjusted by a matching approach, “calculating-test”, in order to assess the quality of the results and the performance of the model. The methodology consists of exploiting two climatic databases (temperature and precipitation), one of which is in-situ and the other spatial, all derived from grid points. Data from the dot grids are processed and stored in specific formats and, through machine learning approaches, complex mathematical equations are worked out and interconnections within the climate system established. Through this mathematical approach, it is possible to predict the future climate of the Sudano-Sahelian zone of Cameroon and to propose adaptation strategies.
基金supported by the National Natural Science Foundation of China(Grant No.41662014)。
文摘The Sonid Zuoqi ductile detachment zone is located at the southeastern margin of the Central Asian orogenic belt(CAOB),striking EW and dipping to the S.The major rock type of the Sonid Zuoqi ductile detachment zone is mylonite derived from granite.The sequence of mylonite features is:(1)S and C foliations of mylonite,and(2)extensional crenulation cleavage(ecc)or C′and the kinematic vorticity(Wk)value changed from 0.70 to 0.95 and from 0.37 to 0.69,respectively;the strain type of the mylonites within the Sonid Zuoqi ductile detachment zone is compressional to planar strain.The strong deformation mylonite and Halatu plutons yielded a zircon U-Pb age of 244 Ma and a zircon(U-Th)/He age of 214 Ma,respectively.Based on the strain and kinematic vorticity analysis,together with the zircon U-Pb and zircon(U-Th)/He ages and the regional tectonic background,the study area experienced three stage evolution:tangential simpleshear(244 Ma),simple-shear-dominated general shear represented by upper crustal extension(224 Ma)and pure-shear-dominated general shear represented by the Halatu pluton doming(214 Ma),which constrained the early Mesozoic NE-SW crustal extension at the southeastern margin of the CAOB.This NE-SW extension probably originated from the postorogenic extensional collapse of the CAOB,subsequent exhumation being controlled by the far afield effects of the closure of the Mongol-Okhotsk belt.
