Although the Zoeppritz equation is suitable for a single interface in a thick deposit, it has some limitations for composite reflection waves from both the floor and the roof of coal seams. Based on the ray model, the...Although the Zoeppritz equation is suitable for a single interface in a thick deposit, it has some limitations for composite reflection waves from both the floor and the roof of coal seams. Based on the ray model, the relationship of the overall reflection coefficient of composite reflection P waves, from coal seam versus incidence angle (AVO), is dis- cussed. The result shows that: 1) the overall reflection coefficient of composite reflection waves from coal seams is a negative value and is determined mainly by the lithology of roof and floor, which is different from the reflection coeffi- cient of a single interface; 2) if the incidence angle ranges from 0° to 6°, the reflection coefficient of composite waves of a coal seam does not change with the incidence angle and 3) if the incidence angle ranges from 6–60° , the reflection coefficient increases monotonically.展开更多
Under the condition of weak anisotropy, the relation of P-wave anisotropy in direction to fractures of coal seams was researched in order to forecast the density and the direction of the fractures. Although the approx...Under the condition of weak anisotropy, the relation of P-wave anisotropy in direction to fractures of coal seams was researched in order to forecast the density and the direction of the fractures. Although the approximate solution by Rtiger is suitable for thick reservoirs, it has some limitations for the composite reflected wave from both roofs and floors of coal seams, as well as multiple reflections. So first, the phase velocity and group velocity as well as their travel time were calculated about the reflected P-wave of the coal seam. Then, the anisotropic coefficients of both roofs and floors were calculated by Rueger formulae and last, the section versus azimuth in fixed offset can be gotten by convolution. In addition, the relation of amplitude of the composite reflected wave to azimuth angle was discussed. The forward modelling results of the coal azimuth anisotropy show these： 1） the coal seam is the strong reflecting layer, but the change of the reflectivity caused by the azimuth anisotropy is smaller; 2） if the azimuth angle is parallel to the crack strike, the reflectivity reaches up to the maximum absolute value, however, if the azimuth angle is perpendicular to the crack strike, the absolute value of the reflection coefficient is minimum; and 3）the reflection coefficient is the cosine function of the azimuth angle and the period is π.展开更多
We analyze the effect of second-harmonic generation（SHG） of primary Lamb wave propagation in a two-layered composite plate, and then investigate the influence of interfacial properties on the said effect at low freq...We analyze the effect of second-harmonic generation（SHG） of primary Lamb wave propagation in a two-layered composite plate, and then investigate the influence of interfacial properties on the said effect at low frequency. It is found that changes in the interfacial properties essentially affect the dispersion relation and then the maximum cumulative distance of the double-frequency Lamb wave generated. This will remarkably influence the efficiency of SHG. To overcome the complications arising from the inherent dispersion and multimode natures in analyzing the SHG effect of Lamb waves, the present work focuses on the analysis of the SHG effect of low-frequency dilatational Lamb wave propagation. Both the numerical analysis and finite element simulation indicate that the SHG effect of low-frequency dilatational Lamb wave propagation is found to be much more sensitive to changes in the interfacial properties than primary Lamb waves. The potential of using the SHG effect of low-frequency dilatational Lamb waves to characterize a minor change in the interfacial properties is analyzed.展开更多
The existence of the sea surface is bound to affect the electromagnetic （EM） scattering from marine targets. When dealing with the composite scattering from targets over a sea surface by applying high-frequency EM t...The existence of the sea surface is bound to affect the electromagnetic （EM） scattering from marine targets. When dealing with the composite scattering from targets over a sea surface by applying high-frequency EM theories, the total scattering field can be decomposed into three parts in low sea states, namely, the direct scattering from the sea surface, the direct scattering from targets and the coupling scattering between the sea surface and targets. With regard to high sea states, breaking waves make the direct scattering from the sea surface and the coupling scattering more complicated. To solve this issue, a scattering model is proposed to analyze the composite scattering from a ship over a rough sea surface under high sea states. To consider the effect of breaking waves, a three dimensional geometric model is adopted together with Ufimtsev＇s theory of edge waves for the scattering from a breaker. In addition, the coupling scattering between targets and breaking waves is taken into account by considering all possible scattering paths. The simulated results indicate that the influence of breaking waves on the scattering field from the sea surface and on the coupling field is non-negligible, and the numerical results also show the effectiveness of the proposed scattering model.展开更多
In this paper,the authors study the centered waves for the two-dimensional(2D for short)pseudo-steady supersonic flow with van der Waals gas satisfied Maxwell's law around a sharp corner.In view of the initial val...In this paper,the authors study the centered waves for the two-dimensional(2D for short)pseudo-steady supersonic flow with van der Waals gas satisfied Maxwell's law around a sharp corner.In view of the initial value of the specific volume and the properties of van der Waals gas,the centered waves at the sharp corner are constructed by classification.It is shown that the supersonic incoming flow turns the sharp corner by a centered simple wave or a centered simple wave with right-contact discontinuity or a composite wave(jump-fan,fan-jump or fan-jump-fan),or a combination of waves and constant state.Moreover,the critical angle of the sharp corner corresponding to the appearance of the vacuum phenomenon is obtained.展开更多
Bionic amphibious robots have important prospects in scientific, commercial, and military fields. Compared with traditional amphibious robots which use propellers/jets for aquatic medium and wheels/tracks for terrestr...Bionic amphibious robots have important prospects in scientific, commercial, and military fields. Compared with traditional amphibious robots which use propellers/jets for aquatic medium and wheels/tracks for terrestrial medium, bionic propulsion method has great advantages in terms of manoeuvrability, efficiency, and reliability, because there is no need to switch between different propulsion systems. To explore the integrated driving technology of amphibious robot, a novel bio-inspired soft robotic fin for amphibious use is proposed in this paper. The bionic fin can swim underwater and walk on land by the same undulating motion. To balance the conflicting demands of flexibility underwater and rigidity on land, the undulating fin adopts a special combination of a membrane fin and a bending spring. A periodic longitudinal wave in horizontal direction has been found generating passively in dynamic analysis. To find the composite wave-driven mechanics, theoretical analysis is conducted based on the walking model and swimming model. A virtual prototype is built in ADAMS software to verify the walking mechanics. The simulation result reveals that the passive longitudinal wave is also periodical and the composite wave contributes to land walking. Finally, an amphibious robot prototype actuated by a pair of undulating fins has been developed. The experiments show that the robot can achieve multiple locomotion, including walking forward/backward, turning in place, swimming underwater, and crossing medium, thus giving evidence to the feasibility of the newly designed undulating fin for amphibious robot.展开更多
We investigate the asymptotic behavior of solutions to the initial boundary value problem for the micropolar fluid model in a half line R+:=(0,∞).Inspired by the relationship between a micropolar fluid model and Navi...We investigate the asymptotic behavior of solutions to the initial boundary value problem for the micropolar fluid model in a half line R+:=(0,∞).Inspired by the relationship between a micropolar fluid model and Navier-Stokes equations,we prove that the composite wave consisting of the transonic boundary layer solution,the 1-rarefaction wave,the viscous 2-contact wave and the 3-rarefaction wave for the inflow problem on the micropolar fluid model is time-asymptotic ally stable under some smallness conditions.Meanwhile,we obtain the global existence of solutions based on the basic energy method.展开更多
In-service structural health monitoring（SHM） technologies are critical for the utilization of composite aircraft structures. We developed a Lamb wave-based in-service SHM technology using built-in piezoelectric actu...In-service structural health monitoring（SHM） technologies are critical for the utilization of composite aircraft structures. We developed a Lamb wave-based in-service SHM technology using built-in piezoelectric actuator/sensor networks to monitor delamination extension in a full-scale composite horizontal tail. The in-service SHM technology combine of damage rapid monitoring（DRM） stage and damage imaging diagnosis（DID） stage allows for real-time monitoring and long term tracking of the structural integrity of composite aircraft structures. DRM stage using spearman rank correlation coeffi cient was introduced to generate a damage index which can be used to monitor the trend of damage extension. The DID stage based on canonical correlation analysis aimed at intuitively highlighting structural damage regions in two-dimensional images. The DRM and DID stages were trialed by an in-service SHM experiment of CFRP T-joint. Finally, the detection capability of the in-service SHM technology was verified in the SHM experiment of a full-scale composite horizontal tail. Experimental results show that the rapid monitoring method effectively monitors the damage occurrence and extension tendency in real time; damage imaging diagnosis results are consistent with those from the failure model of the composite horizontal tail structure.展开更多
A new analytical expression for calculating the wave force on a composite bucket foundation is obtained. Based on the diffraction theory, the analytical solution of the wave pressure and the wave force on the composit...A new analytical expression for calculating the wave force on a composite bucket foundation is obtained. Based on the diffraction theory, the analytical solution of the wave pressure and the wave force on the composite bucket foundation is accurately derived by assigning reasonable boundary conditions. Experiments for the wave pressure on the bucket foundation with a scale of 1：60 under different wave conditions in the wave flume are designed and conducted. The analytical results agree well with the experimental data, and the theoretical approach can accurately predict the wave force on the large-scale structures. The wave pressure distribution on the composite bucket foundation is presented and the influence of the wave height, the water depth and the wave period on the wave force on the composite bucket foundation is investigated. This study provides a quite accurate method to calculate the wave force on a composite bucket foundation, which gives a good framework for future studies of the wave force on other large-scale structures with complex boundaries.展开更多
This paper presents a novel parallel implementation technology for wave-based structural health monitoring (SHM) in laminated composite plates. The wavelet-based B-spline wavelet on he interval (BSWI) element is cons...This paper presents a novel parallel implementation technology for wave-based structural health monitoring (SHM) in laminated composite plates. The wavelet-based B-spline wavelet on he interval (BSWI) element is constructed according to Hamilton’s principle, and the element by element algorithm is parallelly executed on graphics processing unit (GPU) using compute unified device architecture (CUDA) to get the responses in full wave field accurately. By means of the Fourier spectral analysis method,the Mindlin plate theory is selected for wave modeling of laminated composite plates while the Kirchhoff plate theory predicts unreasonably phase and group velocities. Numerical examples involving wave propagation in laminated composite plates without and with crack are performed and discussed in detail. The parallel implementation on GPU is accelerated 146 times comparing with the same wave motion problem executed on central processing unit (CPU). The validity and accuracy of the proposed parallel implementation are also demonstrated by comparing with conventional finite element method (FEM) and the computation time has been reduced from hours to minutes. The damage size and location have been successfully determined according to wave propagation results based on delay-and-sum (DAS). The results show that the proposed parallel implementation of wavelet finite element method (WFEM) is very appropriate and efficient for wave-based SHM in laminated composite plates.展开更多
In order to construct global solutions to two-dimensional(2 D for short)Riemann problems for nonlinear hyperbolic systems of conservation laws,it is important to study various types of wave interactions.This paper dea...In order to construct global solutions to two-dimensional(2 D for short)Riemann problems for nonlinear hyperbolic systems of conservation laws,it is important to study various types of wave interactions.This paper deals with two types of wave interactions for a 2 D nonlinear wave system with a nonconvex equation of state:Rarefaction wave interaction and shock-rarefaction composite wave interaction.In order to construct solutions to these wave interactions,the authors consider two types of Goursat problems,including standard Goursat problem and discontinuous Goursat problem,for a 2 D selfsimilar nonlinear wave system.Global classical solutions to these Goursat problems are obtained by the method of characteristics.The solutions constructed in the paper may be used as building blocks of solutions of 2 D Riemann problems.展开更多
A low-frequency multi-mode ultrasonic Lamb wave method suitable for character- izing the thickness, the density and the elastic constants of the ultra-thin transversely isotropic laminate composite is presented. The &...A low-frequency multi-mode ultrasonic Lamb wave method suitable for character- izing the thickness, the density and the elastic constants of the ultra-thin transversely isotropic laminate composite is presented. The 'ultra-thin' here means that the thickness of the plate is much less than the wavelength of the ultrasonic wave so that the echoes from the front and back faces of the plate can't be separated in the time domain. The dispersion equations for the low frequency ultrasonic Lamb waves with the propagation directions parallel and vertical to the fiber direction are derived. In conjunction with the least square algorithm method, the secant algorithm is used to estimate the parameters of the ultra-thin fiber-reinforced composite layer. The evaluation errors and the sensitivity of the method to different paramters of the thin composite are analyzed. The technique has been used to characterize the ultra-thin grass fiber reinforced PES composite with thickness down to ten percents of the ultrasonic wavelength. It is observed that the agreement between the nominal and the estimation values is reasonably good.展开更多
基金Project 40574058 Supported by the National Natural Science Foundation of China
文摘Although the Zoeppritz equation is suitable for a single interface in a thick deposit, it has some limitations for composite reflection waves from both the floor and the roof of coal seams. Based on the ray model, the relationship of the overall reflection coefficient of composite reflection P waves, from coal seam versus incidence angle (AVO), is dis- cussed. The result shows that: 1) the overall reflection coefficient of composite reflection waves from coal seams is a negative value and is determined mainly by the lithology of roof and floor, which is different from the reflection coeffi- cient of a single interface; 2) if the incidence angle ranges from 0° to 6°, the reflection coefficient of composite waves of a coal seam does not change with the incidence angle and 3) if the incidence angle ranges from 6–60° , the reflection coefficient increases monotonically.
基金Projects 40574058 supported by National Natural Science Foundation of China and 2005cb221500 by the National Basic Research and Development (973)Program of China
文摘Under the condition of weak anisotropy, the relation of P-wave anisotropy in direction to fractures of coal seams was researched in order to forecast the density and the direction of the fractures. Although the approximate solution by Rtiger is suitable for thick reservoirs, it has some limitations for the composite reflected wave from both roofs and floors of coal seams, as well as multiple reflections. So first, the phase velocity and group velocity as well as their travel time were calculated about the reflected P-wave of the coal seam. Then, the anisotropic coefficients of both roofs and floors were calculated by Rueger formulae and last, the section versus azimuth in fixed offset can be gotten by convolution. In addition, the relation of amplitude of the composite reflected wave to azimuth angle was discussed. The forward modelling results of the coal azimuth anisotropy show these： 1） the coal seam is the strong reflecting layer, but the change of the reflectivity caused by the azimuth anisotropy is smaller; 2） if the azimuth angle is parallel to the crack strike, the reflectivity reaches up to the maximum absolute value, however, if the azimuth angle is perpendicular to the crack strike, the absolute value of the reflection coefficient is minimum; and 3）the reflection coefficient is the cosine function of the azimuth angle and the period is π.
基金Supported by the National Natural Science Foundation of China under Grant Nos 11834008,11632004,11474361 and 11622430
文摘We analyze the effect of second-harmonic generation（SHG） of primary Lamb wave propagation in a two-layered composite plate, and then investigate the influence of interfacial properties on the said effect at low frequency. It is found that changes in the interfacial properties essentially affect the dispersion relation and then the maximum cumulative distance of the double-frequency Lamb wave generated. This will remarkably influence the efficiency of SHG. To overcome the complications arising from the inherent dispersion and multimode natures in analyzing the SHG effect of Lamb waves, the present work focuses on the analysis of the SHG effect of low-frequency dilatational Lamb wave propagation. Both the numerical analysis and finite element simulation indicate that the SHG effect of low-frequency dilatational Lamb wave propagation is found to be much more sensitive to changes in the interfacial properties than primary Lamb waves. The potential of using the SHG effect of low-frequency dilatational Lamb waves to characterize a minor change in the interfacial properties is analyzed.
基金Supported by the National Natural Science Foundation of China under Grant No 61372004the Fundamental Research Funds for the Central Universitiesthe Foundation of Science and Technology on Electromagnetic Scattering Laboratory
文摘The existence of the sea surface is bound to affect the electromagnetic （EM） scattering from marine targets. When dealing with the composite scattering from targets over a sea surface by applying high-frequency EM theories, the total scattering field can be decomposed into three parts in low sea states, namely, the direct scattering from the sea surface, the direct scattering from targets and the coupling scattering between the sea surface and targets. With regard to high sea states, breaking waves make the direct scattering from the sea surface and the coupling scattering more complicated. To solve this issue, a scattering model is proposed to analyze the composite scattering from a ship over a rough sea surface under high sea states. To consider the effect of breaking waves, a three dimensional geometric model is adopted together with Ufimtsev＇s theory of edge waves for the scattering from a breaker. In addition, the coupling scattering between targets and breaking waves is taken into account by considering all possible scattering paths. The simulated results indicate that the influence of breaking waves on the scattering field from the sea surface and on the coupling field is non-negligible, and the numerical results also show the effectiveness of the proposed scattering model.
基金supported by the National Natural Science Foundation of China(No.12171305)。
文摘In this paper,the authors study the centered waves for the two-dimensional(2D for short)pseudo-steady supersonic flow with van der Waals gas satisfied Maxwell's law around a sharp corner.In view of the initial value of the specific volume and the properties of van der Waals gas,the centered waves at the sharp corner are constructed by classification.It is shown that the supersonic incoming flow turns the sharp corner by a centered simple wave or a centered simple wave with right-contact discontinuity or a composite wave(jump-fan,fan-jump or fan-jump-fan),or a combination of waves and constant state.Moreover,the critical angle of the sharp corner corresponding to the appearance of the vacuum phenomenon is obtained.
基金supported by the National Natural Science Foundation of China(Grant No.52075537 and Grant No.52105289).
文摘Bionic amphibious robots have important prospects in scientific, commercial, and military fields. Compared with traditional amphibious robots which use propellers/jets for aquatic medium and wheels/tracks for terrestrial medium, bionic propulsion method has great advantages in terms of manoeuvrability, efficiency, and reliability, because there is no need to switch between different propulsion systems. To explore the integrated driving technology of amphibious robot, a novel bio-inspired soft robotic fin for amphibious use is proposed in this paper. The bionic fin can swim underwater and walk on land by the same undulating motion. To balance the conflicting demands of flexibility underwater and rigidity on land, the undulating fin adopts a special combination of a membrane fin and a bending spring. A periodic longitudinal wave in horizontal direction has been found generating passively in dynamic analysis. To find the composite wave-driven mechanics, theoretical analysis is conducted based on the walking model and swimming model. A virtual prototype is built in ADAMS software to verify the walking mechanics. The simulation result reveals that the passive longitudinal wave is also periodical and the composite wave contributes to land walking. Finally, an amphibious robot prototype actuated by a pair of undulating fins has been developed. The experiments show that the robot can achieve multiple locomotion, including walking forward/backward, turning in place, swimming underwater, and crossing medium, thus giving evidence to the feasibility of the newly designed undulating fin for amphibious robot.
基金The research was supported by the National Natural Science Foundation of China(11601164,11971183)the Fundamental Research Funds for the Central Universities(ZQN-701)the Natural Science Foundation of Fujian Province of China(2020J01071).
文摘We investigate the asymptotic behavior of solutions to the initial boundary value problem for the micropolar fluid model in a half line R+:=(0,∞).Inspired by the relationship between a micropolar fluid model and Navier-Stokes equations,we prove that the composite wave consisting of the transonic boundary layer solution,the 1-rarefaction wave,the viscous 2-contact wave and the 3-rarefaction wave for the inflow problem on the micropolar fluid model is time-asymptotic ally stable under some smallness conditions.Meanwhile,we obtain the global existence of solutions based on the basic energy method.
基金Funded by the National Natural Science Foundation of China(Nos.11172053 and 91016024)the New Century Excellent Talents in University(NCET-11-0055)the Fundamental Research Funds for the Central Universities(DUT13ZD(G)06)
文摘In-service structural health monitoring（SHM） technologies are critical for the utilization of composite aircraft structures. We developed a Lamb wave-based in-service SHM technology using built-in piezoelectric actuator/sensor networks to monitor delamination extension in a full-scale composite horizontal tail. The in-service SHM technology combine of damage rapid monitoring（DRM） stage and damage imaging diagnosis（DID） stage allows for real-time monitoring and long term tracking of the structural integrity of composite aircraft structures. DRM stage using spearman rank correlation coeffi cient was introduced to generate a damage index which can be used to monitor the trend of damage extension. The DID stage based on canonical correlation analysis aimed at intuitively highlighting structural damage regions in two-dimensional images. The DRM and DID stages were trialed by an in-service SHM experiment of CFRP T-joint. Finally, the detection capability of the in-service SHM technology was verified in the SHM experiment of a full-scale composite horizontal tail. Experimental results show that the rapid monitoring method effectively monitors the damage occurrence and extension tendency in real time; damage imaging diagnosis results are consistent with those from the failure model of the composite horizontal tail structure.
基金supported by the Funds for Creative Research Groups of China(Grant No.51021004)the National Natural Science Foundation of China(Grant No.51509230)
文摘A new analytical expression for calculating the wave force on a composite bucket foundation is obtained. Based on the diffraction theory, the analytical solution of the wave pressure and the wave force on the composite bucket foundation is accurately derived by assigning reasonable boundary conditions. Experiments for the wave pressure on the bucket foundation with a scale of 1：60 under different wave conditions in the wave flume are designed and conducted. The analytical results agree well with the experimental data, and the theoretical approach can accurately predict the wave force on the large-scale structures. The wave pressure distribution on the composite bucket foundation is presented and the influence of the wave height, the water depth and the wave period on the wave force on the composite bucket foundation is investigated. This study provides a quite accurate method to calculate the wave force on a composite bucket foundation, which gives a good framework for future studies of the wave force on other large-scale structures with complex boundaries.
基金supported by the National Natural Science Foundation of China (Grant Nos. 51421004 & 51405369)the National Key Basic Research Program of China (Grant No. 2015CB057400)+1 种基金the China Postdoctoral Science Foundation (Grant No. 2014M560766)the China Scholarship Council,and the Fundamental Research Funds for the Central Universities(Grant No. xjj2014107)
文摘This paper presents a novel parallel implementation technology for wave-based structural health monitoring (SHM) in laminated composite plates. The wavelet-based B-spline wavelet on he interval (BSWI) element is constructed according to Hamilton’s principle, and the element by element algorithm is parallelly executed on graphics processing unit (GPU) using compute unified device architecture (CUDA) to get the responses in full wave field accurately. By means of the Fourier spectral analysis method,the Mindlin plate theory is selected for wave modeling of laminated composite plates while the Kirchhoff plate theory predicts unreasonably phase and group velocities. Numerical examples involving wave propagation in laminated composite plates without and with crack are performed and discussed in detail. The parallel implementation on GPU is accelerated 146 times comparing with the same wave motion problem executed on central processing unit (CPU). The validity and accuracy of the proposed parallel implementation are also demonstrated by comparing with conventional finite element method (FEM) and the computation time has been reduced from hours to minutes. The damage size and location have been successfully determined according to wave propagation results based on delay-and-sum (DAS). The results show that the proposed parallel implementation of wavelet finite element method (WFEM) is very appropriate and efficient for wave-based SHM in laminated composite plates.
基金supported by the National Natural Science Foundation of China(No.11301326)。
文摘In order to construct global solutions to two-dimensional(2 D for short)Riemann problems for nonlinear hyperbolic systems of conservation laws,it is important to study various types of wave interactions.This paper deals with two types of wave interactions for a 2 D nonlinear wave system with a nonconvex equation of state:Rarefaction wave interaction and shock-rarefaction composite wave interaction.In order to construct solutions to these wave interactions,the authors consider two types of Goursat problems,including standard Goursat problem and discontinuous Goursat problem,for a 2 D selfsimilar nonlinear wave system.Global classical solutions to these Goursat problems are obtained by the method of characteristics.The solutions constructed in the paper may be used as building blocks of solutions of 2 D Riemann problems.
基金the National Natural Science Foundation of China (No. 69631020) and theOffice of Naval Research of America (00014-93-1-0340).
文摘A low-frequency multi-mode ultrasonic Lamb wave method suitable for character- izing the thickness, the density and the elastic constants of the ultra-thin transversely isotropic laminate composite is presented. The 'ultra-thin' here means that the thickness of the plate is much less than the wavelength of the ultrasonic wave so that the echoes from the front and back faces of the plate can't be separated in the time domain. The dispersion equations for the low frequency ultrasonic Lamb waves with the propagation directions parallel and vertical to the fiber direction are derived. In conjunction with the least square algorithm method, the secant algorithm is used to estimate the parameters of the ultra-thin fiber-reinforced composite layer. The evaluation errors and the sensitivity of the method to different paramters of the thin composite are analyzed. The technique has been used to characterize the ultra-thin grass fiber reinforced PES composite with thickness down to ten percents of the ultrasonic wavelength. It is observed that the agreement between the nominal and the estimation values is reasonably good.
