To investigate the thermal and mechanical behavior of casting wheel,a two-dimensional thermoelastic-plastic finite element model was used to predict the temperature,stress and distortion distribution of the casting wh...To investigate the thermal and mechanical behavior of casting wheel,a two-dimensional thermoelastic-plastic finite element model was used to predict the temperature,stress and distortion distribution of the casting wheel during the wheel and belt continuous casting process.The effects of grinding thickness and casting speed on the thermal and mechanical behaviors of the center of the hot face of the casting wheel were discussed in detail.In each rotation,the casting wheel passes through four different spray zones.The results show that the temperature distribution of the casting wheel in different spray zones is similar,the temperature of the hot face is the highest and the temperature reaches the peak in the spray zoneⅢ.The stress and distortion depend on the temperature distribution,and the maximum stress and distortion of the hot face are 358.2 MPa and 1.82 mm,respectively.The temperature at the center of the hot face decreases with increasing grinding thickness and increases with increasing casting speed.展开更多
Hypo-peritectic steels are widely used in various industrial fields because of their high strength,high toughness,high processability,high weldability,and low material cost.However,surface defects are liable to occur ...Hypo-peritectic steels are widely used in various industrial fields because of their high strength,high toughness,high processability,high weldability,and low material cost.However,surface defects are liable to occur during continuous casting,which includes depression,longitudinal cracks,deep oscillation marks,and severe level fluctuation with slag entrapment.The high-efficiency production of hypo-peritectic steels by continuous casting is still a great challenge due to the limited understanding of the mechanism of peritectic solidification.This work reviews the definition and classification of hypo-peritectic steels and introduces the formation tendency of common surface defects related to peritectic solidification.New achievements in the mechanism of peritectic reaction and transformation have been listed.Finally,countermeasures to avoiding surface defects of hypo-peritectic steels duiring continuous casting are summarized.Enlightening certain points in the continuous casting of hypo-peritectic steels and the development of new techniques to overcome the present problems will be a great aid to researchers.展开更多
The horizontal continuous casting process,the initial step in TP2 copper tubular processing,directly determines the microstructure and properties of copper tubular.However,the process parameters of the continuous cast...The horizontal continuous casting process,the initial step in TP2 copper tubular processing,directly determines the microstructure and properties of copper tubular.However,the process parameters of the continuous casting characterize time variation,multiple disturbances and strong coupling.As a consequence,their influence on a casting billet is difficult to be determined.Due to the above issues,the common factor and special factor analysis of the factor analysis model were used in this study,and the casting experiment and billet metallographic experiment were carried out to diagnose and analyze the reason of the microstructure inhomogeneity.The multiple process parameters were studied and classified using common factor analysis,2 the cast billets with abnormal microstructures were identified by GT^(2) statistics,and the most important factors affecting the microstructural homogeneity were found by special factor analysis.The calculated and experimental results show that the principal parameters influencing the inhomogeneity of solidified microstructure are the primary inlet water pressure and the primary outlet water temperature.According to the consequence of the above investigation,the inhomogeneity of the copper billet microstructure can be effectively improved when the process parameters are controlled and adjusted.展开更多
In view of the service failure and low continuous casting production efficiency due to the corrosion of refractories at the slag-line in submerged entry nozzles,a submerged entry nozzle for low-carbon aluminum killed ...In view of the service failure and low continuous casting production efficiency due to the corrosion of refractories at the slag-line in submerged entry nozzles,a submerged entry nozzle for low-carbon aluminum killed steel continuous casting in one steel plant was sampled and taken as the research object to analyze the causes and the mechanism of refractory corrosion at the slag-line.The results show that the core issue of the corrosion and necking of the slag-line materials is that the slag-line material are eroded,dissolved,and reacted by the mold flux gradually.Therefore,it is important to suppress or avoid the contact and reaction between the mold flux and slag-line materials.展开更多
In the present research, the orthogonal experiment was carried out to investigate the influence of different austempering process parameters(i.e. austenitizing temperature and time, and austempering temperature and ti...In the present research, the orthogonal experiment was carried out to investigate the influence of different austempering process parameters(i.e. austenitizing temperature and time, and austempering temperature and time) on microstructure and mechanical properties of LZQT500-7 ductile iron dense bars with 172 mm in diameter which were produced by horizontal continuous casting(HCC). The results show that the major factors influencing the hardness of austempered ductile iron(ADI) are austenitizing temperature and austempering temperature. The fraction of retained austenite increases as the austenitizing and austempering temperatures increase. When austenitizing temperature is low, acicular ferrite and retained austenite can be effi ciently obtained by appropriately extending the austenitizing time. The proper austmepering time could ensure enough stability of retained austenite and prevent high carbon austenite decomposition. The optimal mechanical properties of ADI can be achieved with the following process parameters: austenitizing temperature and time are 866 °C and 135 min, and austempering temperature and time are 279 °C and 135 min, respectively. The microstructure of ADI under the optimal austempering process consists of fi ne acicular ferrite and a small amount of retained austenite, and the hardness, tensile strength, yield strength, elongation and impact toughness of the bars are HBW 476, 1670 MPa, 1428 MPa, 2.93% and 25.7 J, respectively.展开更多
Computational simulations and high-temperature measurements of velocities near the surface of a mold were carried out by using the rod deflection method to study the effects of various operating parameters on the flow...Computational simulations and high-temperature measurements of velocities near the surface of a mold were carried out by using the rod deflection method to study the effects of various operating parameters on the flow field in slab continuous casting(CC)molds with narrow widths for the production of automobile exposed panels.Reasonable agreement between the calculated results and measured subsurface velocities of liquid steel was obtained under different operating parameters of the CC process.The simulation results reveal that the flow field in the horizontal plane located 50 mm from the meniscus can be used as the characteristic flow field to optimize the flow field of molten steel in the mold.Increases in casting speed can increase the subsurface velocity of molten steel and shift the position of the vortex core downward in the downward circulation zone.The flow field of liquid steel in a 1040 mm-wide slab CC mold can be improved by an Ar gas flow rate of 7 L·min^−1 and casting speed of 1.7 m·min^−1.Under the present experimental conditions,the double-roll flow pattern is generally stable at a submerged entry nozzle immersion depth of 170 mm.展开更多
The quantitative evaluation of multi-process collaborative operation is of great significance for the improvement of production planning and scheduling in steelmaking–continuous casting sections(SCCSs). However, this...The quantitative evaluation of multi-process collaborative operation is of great significance for the improvement of production planning and scheduling in steelmaking–continuous casting sections(SCCSs). However, this evaluation is difficult since it relies on an in-depth understanding of the operating mechanism of SCCSs, and few existing methods can be used to conduct the evaluation, due to the lack of full-scale consideration of the multiple factors related to the production operation. In this study, three quantitative models were developed, and the multiprocess collaborative operation level was evaluated through the laminar-flow operation degree, the process matching degree, and the scheduling strategy availability degree. Based on the evaluation models for the laminar-flow operation and process matching levels, this study investigated the production status of two steelmaking plants, plants A and B, based on actual production data. The average laminar-flow operation(process matching) degrees of SCCSs were obtained as 0.638(0.610) and 1.000(0.759) for plants A and B, respectively, for the period of April to July 2019. Then, a scheduling strategy based on the optimization of the furnace-caster coordinating mode was suggested for plant A. Simulation experiments showed higher availability than the greedy-based and manual strategies. After the proposed scheduling strategy was applied,the average process matching degree of the SCCS of plant A increased by 4.6% for the period of September to November 2019. The multi-process collaborative operation level was improved with fewer adjustments and interruptions in casting.展开更多
In the present research, microstructure refinement of a high-Nb TiAl alloy(Ti-48Al-8Nb-0.15B) was realized by means of the electromagnetic continuous casting(EMCC) technique. The microstructure of an ingot obtained by...In the present research, microstructure refinement of a high-Nb TiAl alloy(Ti-48Al-8Nb-0.15B) was realized by means of the electromagnetic continuous casting(EMCC) technique. The microstructure of an ingot obtained by EMCC was analyzed using scanning electron microscopy(SEM). As compared with the raw as-cast al oy, the obtained EMCC alloy presented a much finer microstructure with lamellar colonies with a mean size of about 50-70 μm because the electromagnetic stirring broke initial dendrites and enhanced the heterogeneous nucleation. As the grains were refined, the properties of the TiAl alloy were improved significantly. This implies that the EMCC technique could offer the possibility of application for high-Nb TiAl alloys with a refined microstructure and excel ent properties to be used as a structural material.展开更多
To provide theoretical basis and practical guidance for preparing composite rods by direct continuous casting, copper-clad aluminum composite rods of external copper layer diameter 12 mm and inner aluminum core diamet...To provide theoretical basis and practical guidance for preparing composite rods by direct continuous casting, copper-clad aluminum composite rods of external copper layer diameter 12 mm and inner aluminum core diameter 8 mm were manufactured. Orthogonal tests consisted of three factors and three levels were carried out to research the effects of melting copper temperature, continuous casting speed and nitrogen pressure on the performance of composite rods. Results showed that nitrogen pressure is the most important factor in influencing the surface quality; continuous casting speed is the most important factor in influencing copper & aluminum inter diffusion amount. Nitrogen pressure can noticeably improve the surface quality and make the rods easily be drawn out, but the surface quality does not show visible improvement when the nitrogen pressure is above 0.05 MPa. Measured by tests, the compound layer can be divided into three types according to its cladding layer degree: deficient cladding, normal cladding and excess cladding. The diameter of normal copper-clad aluminum composite rods can be successfully drawn less than 0.6 mm without annealing.展开更多
The periodic bending deformation in the direction of casting occurs at the liquid/solid interface of billet due to the roller supporting force and the pressure of molten metal in the process of continuous casting. Bas...The periodic bending deformation in the direction of casting occurs at the liquid/solid interface of billet due to the roller supporting force and the pressure of molten metal in the process of continuous casting. Based on this fact, a qualitative expression of solute concentration in columnar crystal zone for continuous casting billet is established, which agrees with the experimental results basically. Therefore, it is favorable to gain a columnar structure with less segregation by adopting a caster with compactly distributed small rollers and enhancing the cooling intensity in secondary cooling zone.展开更多
Crystallization growth of single-crystal Cu by continuous casting has been investigated using self- designed horizontal continuous casting equipment and XRD. Experimental results showed that the crystallization plane ...Crystallization growth of single-crystal Cu by continuous casting has been investigated using self- designed horizontal continuous casting equipment and XRD. Experimental results showed that the crystallization plane of (311), (220) and (111) were eliminated sequentially in evolutionary process. The final growth plane of crystal was (200), the direction of crystallization was [100], the growwth direction of both sides of the rod inclined to axis, and the degree of deviation of direction [100] from the crystal axis was less than 10? In order to produce high quality single crystal, the solid-liquid interface morphology must be smooth, even be planar.展开更多
On the interface of the Cu-Al composite plate from horizontal continuous casting,the eutectic microstructure layer thickness ac-counts for more than 90%of the total interface thickness,and the deformation in rolling f...On the interface of the Cu-Al composite plate from horizontal continuous casting,the eutectic microstructure layer thickness ac-counts for more than 90%of the total interface thickness,and the deformation in rolling forming plays an important role in the quality of the composite plate.The eutectic microstructure material on the interface of the Cu-Al composite plate was prepared by changing the cooling rate of ingot solidification and the deformation in hot compression was investigated.The results show that when the deformation temperature is over 300℃,the softening effect of dynamic recrystallization ofα-Al is greater than the hardening effect,and uniform plastic deformation of eutectic microstructure is caused.The constitutive equation of flow stress in the eutectic microstructure layer was established by Arrhenius hy-perbolic-sine mathematics model,providing a reliable theoretical basis for the deformation of the Cu-Al composite plate.展开更多
A Lagrangian relaxation(LR) approach was presented which is with machine capacity relaxation and operation precedence relaxation for solving a flexible job shop(FJS) scheduling problem from the steelmaking-refining-co...A Lagrangian relaxation(LR) approach was presented which is with machine capacity relaxation and operation precedence relaxation for solving a flexible job shop(FJS) scheduling problem from the steelmaking-refining-continuous casting process. Unlike the full optimization of LR problems in traditional LR approaches, the machine capacity relaxation is optimized asymptotically, while the precedence relaxation is optimized approximately due to the NP-hard nature of its LR problem. Because the standard subgradient algorithm(SSA) cannot solve the Lagrangian dual(LD) problem within the partial optimization of LR problem, an effective deflected-conditional approximate subgradient level algorithm(DCASLA) was developed, named as Lagrangian relaxation level approach. The efficiency of the DCASLA is enhanced by a deflected-conditional epsilon-subgradient to weaken the possible zigzagging phenomena. Computational results and comparisons show that the proposed methods improve significantly the efficiency of the LR approach and the DCASLA adopting capacity relaxation strategy performs best among eight methods in terms of solution quality and running time.展开更多
A general mathematical model and boundary condition applicable to momentum and heat transfer in the semisolid continuous casting(SCC) process was established. Using the model, the numerical simulation of the momentum ...A general mathematical model and boundary condition applicable to momentum and heat transfer in the semisolid continuous casting(SCC) process was established. Using the model, the numerical simulation of the momentum and heat transfer of molten metal was carried out in the SCC system. The obtained results fit well with the measured ones. Moreover, using the numerical simulating software, the effect of various factors on breakout and breakage was explored. The obtained results show that heat flow density of copper mold and the withdrawal beginning time are two major influencing factors. The larger the heat flow density of copper mold, or the shorter the withdrawal beginning time, the more stable the semisolid continuous casting process. [展开更多
Mg-9Gd-3Y-1.5Zn-0.8Zr alloys own high strength,good heat and corrosion resistance.However,it is difficult for the fabrication of large-scale billets,due to the poor deformation ability and strong hot-crack tendency.Th...Mg-9Gd-3Y-1.5Zn-0.8Zr alloys own high strength,good heat and corrosion resistance.However,it is difficult for the fabrication of large-scale billets,due to the poor deformation ability and strong hot-crack tendency.This work investigated the casting process on the microstructures and flow stress behaviors of the semi-continuous casting billets for the fabrication of large-scale Mg-9Gd-3Y-1.5Zn-0.8Zr billets.The casting process(electromagnetic intensity and casting speed)shows outstanding effects on the microstructures and flow stress behavior of the billets.The billets with the specific casting process(I=68 A,V=65 mm/min)exhibit uniform microstructures and good deformation uniformity.展开更多
The two-phase zone continuous casting(TZCC)technique was used to continuously cast high-strength aluminum alloy hollow billets,and a verified 3D model of TZCC was used to simulate the flow and temperature fields at ca...The two-phase zone continuous casting(TZCC)technique was used to continuously cast high-strength aluminum alloy hollow billets,and a verified 3D model of TZCC was used to simulate the flow and temperature fields at casting speeds of 2-6 mm·min^(-1).Hollow billets under the same conditions were prepared,and their macro/microstructures were analyzed by an optical microscope and a scanning electron microscope.During the TZCC process,a circular fluid flow appears in front of the mushy zone,and the induction heated stepped mold and convective heat transfer result in a curved solidification front with depressed region near the inner wall and a vertical temperature gradient.The deflection of the solidification front decreases and the average cooling rate in the mushy zone increases with increasing casting speed.Experimental results for a 2D12 alloy show that hot tearing periodically appears in the hollow billet accompanied by macrosegregation near the inner wall at casting speeds of 2 and 4 mm·min^(-1),while macroscopic defects of hot tearing and macrosegregation weaken and the average size of columnar crystals in the hollow billets decreases with further increasing casting speed.2D12 aluminum alloy hollow billets with no macroscopic defects,the finest columnar crystals,and excellent mechanical properties were prepared by TZCC at a casting speed of 6 mm·min^(-1),which is beneficial for the further plastic forming process.展开更多
Understanding the transformation of liquid steel to solid steel is the most fundamental aspect of continuous casting;however,it remains a complex subject with a number of unresolved issues.In this paper,the following ...Understanding the transformation of liquid steel to solid steel is the most fundamental aspect of continuous casting;however,it remains a complex subject with a number of unresolved issues.In this paper,the following aspects of mold operation which give rise to sub-surface defects will be discussed;meniscus solidification,surface and interfacial energies,effects of gas bubbles,and the dynamic nature of the liquid slag-liquid steel interface.展开更多
A matrix encoding scheme for the steelmaking continuous casting( SCC) production scheduling( SCCPS) problem and the corresponding decoding method are proposed. Based on it,a cross entropy( CE) method is adopted and an...A matrix encoding scheme for the steelmaking continuous casting( SCC) production scheduling( SCCPS) problem and the corresponding decoding method are proposed. Based on it,a cross entropy( CE) method is adopted and an improved cross entropy( ICE) algorithm is proposed to solve the SCCPS problem to minimize total power consumption. To describe the distribution of the solution space of the CE method,a probability model is built and used to generate individuals by sampling and a probability updating mechanism is introduced to trace the promising samples. For the ICE algorithm,some samples are generated by the heuristic rules for the shortest makespan due to the relation between the makespan and the total power consumption,which can reduce the search space greatly. The optimal sample in each iteration is retained through a retention mechanism to ensure that the historical optimal sample is not lost so as to improve the efficiency and global convergence. A local search procedure is carried out on a part of better samples so as to improve the local exploitation capability of the ICE algorithm and get a better result. The parameter setting is investigated by the Taguchi method of design-of-experiment. A number of simulation experiments are implemented to validate the effectiveness of the ICE algorithm in solving the SCCPS problem and also the superiority of the ICE algorithm is verified through the comparison with the standard cross entropy( SCE) algorithm.展开更多
The causes, the formation process, and the prevention of submerged entry nozzle(SEN) clogging were introduced. The influence of electric field on the SEN clogging was focused on, including the basic theory and measure...The causes, the formation process, and the prevention of submerged entry nozzle(SEN) clogging were introduced. The influence of electric field on the SEN clogging was focused on, including the basic theory and measurement of SEN charging,the preliminary research on SEN charging, the influence of molten steel on the wetting behavior of refractory materials in electric field, and the influence of electric field on the oxide inclusions in molten steel. Based on the influence of the hydrodynamics, chemistry and other factors on refractory materials, structure, inclusion particle transfer and adhesion, many anti-clogging researches have been carried out, such as optimizing process conditions, compositing anti-clogging inner lining materials, innovating SEN structure and applying physical fields, which solve the problem of SEN clogging to a certain extent.However, the problems of weak adaptability and superficial study on clogging mechanism are still prominent. The electric field control is a new technology to prevent clogging. Although it has achieved certain results in on-site continuous casting trials,some problems such as the method of applying electric field, the electric field parameters and the equipment still need to be gradually improved, and the surface characteristics of inclusions and SEN materials at high temperatures need to be further studied. It was pointed out that the combination of materials and applied electric field will become an important direction for SEN anti-clogging technology.展开更多
A mold flux is widely used to modify heat transfer rates in continuous casting,and crystallization of the mold flux has been identified as a primary factor that influences heat flux from the strand to the mold.As the ...A mold flux is widely used to modify heat transfer rates in continuous casting,and crystallization of the mold flux has been identified as a primary factor that influences heat flux from the strand to the mold.As the harsh environment and the very high transient nature of the mold caster,the study of dynamic mold flux melting and crystallization as well as their effects on heat transfer has not been conducted widely.By using an infrared radiation emitter,a high level heat flux was applied to a copper mold covered with solid mold flux disk to simulate the heat transfer phenomena in continuous casting.By this technique it is possible to have a liquid layer,a crystalline layer and a glassy layer in contact with one another and,by varying the energy input,it is possible to study the dynamic nature of the film and its effect on the heat transfer rate.A general heat transfer model was also developed to allow the prediction of the effect of varying the thickness of the three potential layers in the flux film.展开更多
基金financially supported by the National Natural Science Foundation of China(Grant No.U20A20289)the Innovative Research Groups Project of the Natural Science Foundation of Hebei Province(Grant No.E2021203011)the Central Government Guides Local Science and Technology Development Fund Project(Grant No.206Z1601G)。
文摘To investigate the thermal and mechanical behavior of casting wheel,a two-dimensional thermoelastic-plastic finite element model was used to predict the temperature,stress and distortion distribution of the casting wheel during the wheel and belt continuous casting process.The effects of grinding thickness and casting speed on the thermal and mechanical behaviors of the center of the hot face of the casting wheel were discussed in detail.In each rotation,the casting wheel passes through four different spray zones.The results show that the temperature distribution of the casting wheel in different spray zones is similar,the temperature of the hot face is the highest and the temperature reaches the peak in the spray zoneⅢ.The stress and distortion depend on the temperature distribution,and the maximum stress and distortion of the hot face are 358.2 MPa and 1.82 mm,respectively.The temperature at the center of the hot face decreases with increasing grinding thickness and increases with increasing casting speed.
基金financially supported by the Fundamental Research Funds for the Central Universities(No.FRF-TP-19-017A3)the National Natural Science Foundation of China(No.51874026)。
文摘Hypo-peritectic steels are widely used in various industrial fields because of their high strength,high toughness,high processability,high weldability,and low material cost.However,surface defects are liable to occur during continuous casting,which includes depression,longitudinal cracks,deep oscillation marks,and severe level fluctuation with slag entrapment.The high-efficiency production of hypo-peritectic steels by continuous casting is still a great challenge due to the limited understanding of the mechanism of peritectic solidification.This work reviews the definition and classification of hypo-peritectic steels and introduces the formation tendency of common surface defects related to peritectic solidification.New achievements in the mechanism of peritectic reaction and transformation have been listed.Finally,countermeasures to avoiding surface defects of hypo-peritectic steels duiring continuous casting are summarized.Enlightening certain points in the continuous casting of hypo-peritectic steels and the development of new techniques to overcome the present problems will be a great aid to researchers.
基金This work is financially supported by Basic Scientific Project of Liaoning Provincial Department of Education(LJKMZ20220591)Science and Technology Plan Project of Changzhou,China(CQ20220057).
文摘The horizontal continuous casting process,the initial step in TP2 copper tubular processing,directly determines the microstructure and properties of copper tubular.However,the process parameters of the continuous casting characterize time variation,multiple disturbances and strong coupling.As a consequence,their influence on a casting billet is difficult to be determined.Due to the above issues,the common factor and special factor analysis of the factor analysis model were used in this study,and the casting experiment and billet metallographic experiment were carried out to diagnose and analyze the reason of the microstructure inhomogeneity.The multiple process parameters were studied and classified using common factor analysis,2 the cast billets with abnormal microstructures were identified by GT^(2) statistics,and the most important factors affecting the microstructural homogeneity were found by special factor analysis.The calculated and experimental results show that the principal parameters influencing the inhomogeneity of solidified microstructure are the primary inlet water pressure and the primary outlet water temperature.According to the consequence of the above investigation,the inhomogeneity of the copper billet microstructure can be effectively improved when the process parameters are controlled and adjusted.
基金the financial support from the National Natural Science Foundation of China(Grant No.52174302,No.51932008 and No.52304347)the Central China Thousand Talents Project(204200510011).
文摘In view of the service failure and low continuous casting production efficiency due to the corrosion of refractories at the slag-line in submerged entry nozzles,a submerged entry nozzle for low-carbon aluminum killed steel continuous casting in one steel plant was sampled and taken as the research object to analyze the causes and the mechanism of refractory corrosion at the slag-line.The results show that the core issue of the corrosion and necking of the slag-line materials is that the slag-line material are eroded,dissolved,and reacted by the mold flux gradually.Therefore,it is important to suppress or avoid the contact and reaction between the mold flux and slag-line materials.
基金financially supported by the fund of the Key Projects of Shaanxi Provincial International Technology Cooperation Plan(2013KW16)the Scientific Research Program funded by Shaanxi Provincial Education Department(2013JK0914)+2 种基金the State Key Laboratory of Solidifi cation Processing in NWPU(SKLSP201115)the Scientific Research Project of Xi'an University of Technology(2013CX004)the fund of the Key Laboratory of Electrical Materials and Infi ltration Technology of Shaanxi Province,China(2014)
文摘In the present research, the orthogonal experiment was carried out to investigate the influence of different austempering process parameters(i.e. austenitizing temperature and time, and austempering temperature and time) on microstructure and mechanical properties of LZQT500-7 ductile iron dense bars with 172 mm in diameter which were produced by horizontal continuous casting(HCC). The results show that the major factors influencing the hardness of austempered ductile iron(ADI) are austenitizing temperature and austempering temperature. The fraction of retained austenite increases as the austenitizing and austempering temperatures increase. When austenitizing temperature is low, acicular ferrite and retained austenite can be effi ciently obtained by appropriately extending the austenitizing time. The proper austmepering time could ensure enough stability of retained austenite and prevent high carbon austenite decomposition. The optimal mechanical properties of ADI can be achieved with the following process parameters: austenitizing temperature and time are 866 °C and 135 min, and austempering temperature and time are 279 °C and 135 min, respectively. The microstructure of ADI under the optimal austempering process consists of fi ne acicular ferrite and a small amount of retained austenite, and the hardness, tensile strength, yield strength, elongation and impact toughness of the bars are HBW 476, 1670 MPa, 1428 MPa, 2.93% and 25.7 J, respectively.
基金This work was financially supported by the Hunan Valin Lianyuan Iron&Steel Co.,Ltd.,China(No.18H00582).The authors are grateful to Hunan Valin Lianyuan Iron&Steel Co.,Ltd.,China for their assistance with the industrial measurement of velocities near the mold surface.
文摘Computational simulations and high-temperature measurements of velocities near the surface of a mold were carried out by using the rod deflection method to study the effects of various operating parameters on the flow field in slab continuous casting(CC)molds with narrow widths for the production of automobile exposed panels.Reasonable agreement between the calculated results and measured subsurface velocities of liquid steel was obtained under different operating parameters of the CC process.The simulation results reveal that the flow field in the horizontal plane located 50 mm from the meniscus can be used as the characteristic flow field to optimize the flow field of molten steel in the mold.Increases in casting speed can increase the subsurface velocity of molten steel and shift the position of the vortex core downward in the downward circulation zone.The flow field of liquid steel in a 1040 mm-wide slab CC mold can be improved by an Ar gas flow rate of 7 L·min^−1 and casting speed of 1.7 m·min^−1.Under the present experimental conditions,the double-roll flow pattern is generally stable at a submerged entry nozzle immersion depth of 170 mm.
基金financially supported by the National Natural Science Foundation of China (Nos.50874014 and 51974023)the Fundamental Research Funds for Central Universities (No.FRF-BR-17-029A)。
文摘The quantitative evaluation of multi-process collaborative operation is of great significance for the improvement of production planning and scheduling in steelmaking–continuous casting sections(SCCSs). However, this evaluation is difficult since it relies on an in-depth understanding of the operating mechanism of SCCSs, and few existing methods can be used to conduct the evaluation, due to the lack of full-scale consideration of the multiple factors related to the production operation. In this study, three quantitative models were developed, and the multiprocess collaborative operation level was evaluated through the laminar-flow operation degree, the process matching degree, and the scheduling strategy availability degree. Based on the evaluation models for the laminar-flow operation and process matching levels, this study investigated the production status of two steelmaking plants, plants A and B, based on actual production data. The average laminar-flow operation(process matching) degrees of SCCSs were obtained as 0.638(0.610) and 1.000(0.759) for plants A and B, respectively, for the period of April to July 2019. Then, a scheduling strategy based on the optimization of the furnace-caster coordinating mode was suggested for plant A. Simulation experiments showed higher availability than the greedy-based and manual strategies. After the proposed scheduling strategy was applied,the average process matching degree of the SCCS of plant A increased by 4.6% for the period of September to November 2019. The multi-process collaborative operation level was improved with fewer adjustments and interruptions in casting.
基金financially supported by the National Science Foundation of China(Grant No.51171053 and No.51471062)
文摘In the present research, microstructure refinement of a high-Nb TiAl alloy(Ti-48Al-8Nb-0.15B) was realized by means of the electromagnetic continuous casting(EMCC) technique. The microstructure of an ingot obtained by EMCC was analyzed using scanning electron microscopy(SEM). As compared with the raw as-cast al oy, the obtained EMCC alloy presented a much finer microstructure with lamellar colonies with a mean size of about 50-70 μm because the electromagnetic stirring broke initial dendrites and enhanced the heterogeneous nucleation. As the grains were refined, the properties of the TiAl alloy were improved significantly. This implies that the EMCC technique could offer the possibility of application for high-Nb TiAl alloys with a refined microstructure and excel ent properties to be used as a structural material.
基金financially supported by the Program for New Century Excellent Talents in University(NCET-12-0849)the Fundamental Research Funds for the Central Universities(13ZD12)the National Natural Science Foundation of China(No.51006034)
文摘To provide theoretical basis and practical guidance for preparing composite rods by direct continuous casting, copper-clad aluminum composite rods of external copper layer diameter 12 mm and inner aluminum core diameter 8 mm were manufactured. Orthogonal tests consisted of three factors and three levels were carried out to research the effects of melting copper temperature, continuous casting speed and nitrogen pressure on the performance of composite rods. Results showed that nitrogen pressure is the most important factor in influencing the surface quality; continuous casting speed is the most important factor in influencing copper & aluminum inter diffusion amount. Nitrogen pressure can noticeably improve the surface quality and make the rods easily be drawn out, but the surface quality does not show visible improvement when the nitrogen pressure is above 0.05 MPa. Measured by tests, the compound layer can be divided into three types according to its cladding layer degree: deficient cladding, normal cladding and excess cladding. The diameter of normal copper-clad aluminum composite rods can be successfully drawn less than 0.6 mm without annealing.
文摘The periodic bending deformation in the direction of casting occurs at the liquid/solid interface of billet due to the roller supporting force and the pressure of molten metal in the process of continuous casting. Based on this fact, a qualitative expression of solute concentration in columnar crystal zone for continuous casting billet is established, which agrees with the experimental results basically. Therefore, it is favorable to gain a columnar structure with less segregation by adopting a caster with compactly distributed small rollers and enhancing the cooling intensity in secondary cooling zone.
文摘Crystallization growth of single-crystal Cu by continuous casting has been investigated using self- designed horizontal continuous casting equipment and XRD. Experimental results showed that the crystallization plane of (311), (220) and (111) were eliminated sequentially in evolutionary process. The final growth plane of crystal was (200), the direction of crystallization was [100], the growwth direction of both sides of the rod inclined to axis, and the degree of deviation of direction [100] from the crystal axis was less than 10? In order to produce high quality single crystal, the solid-liquid interface morphology must be smooth, even be planar.
基金This work was financially supported by the National Key Research and Development Program of China(No.2018YFA0707303)the National Natural Science Foundation for Distinguished Young Scholars of China(No.51925401).
文摘On the interface of the Cu-Al composite plate from horizontal continuous casting,the eutectic microstructure layer thickness ac-counts for more than 90%of the total interface thickness,and the deformation in rolling forming plays an important role in the quality of the composite plate.The eutectic microstructure material on the interface of the Cu-Al composite plate was prepared by changing the cooling rate of ingot solidification and the deformation in hot compression was investigated.The results show that when the deformation temperature is over 300℃,the softening effect of dynamic recrystallization ofα-Al is greater than the hardening effect,and uniform plastic deformation of eutectic microstructure is caused.The constitutive equation of flow stress in the eutectic microstructure layer was established by Arrhenius hy-perbolic-sine mathematics model,providing a reliable theoretical basis for the deformation of the Cu-Al composite plate.
基金Projects(51435009,51575212,61573249,61371200)supported by the National Natural Science Foundation of ChinaProjects(2015T80798,2014M552040,2014M561250,2015M571328)supported by Postdoctoral Science Foundation of ChinaProject(L2015372)supported by Liaoning Province Education Administration,China
文摘A Lagrangian relaxation(LR) approach was presented which is with machine capacity relaxation and operation precedence relaxation for solving a flexible job shop(FJS) scheduling problem from the steelmaking-refining-continuous casting process. Unlike the full optimization of LR problems in traditional LR approaches, the machine capacity relaxation is optimized asymptotically, while the precedence relaxation is optimized approximately due to the NP-hard nature of its LR problem. Because the standard subgradient algorithm(SSA) cannot solve the Lagrangian dual(LD) problem within the partial optimization of LR problem, an effective deflected-conditional approximate subgradient level algorithm(DCASLA) was developed, named as Lagrangian relaxation level approach. The efficiency of the DCASLA is enhanced by a deflected-conditional epsilon-subgradient to weaken the possible zigzagging phenomena. Computational results and comparisons show that the proposed methods improve significantly the efficiency of the LR approach and the DCASLA adopting capacity relaxation strategy performs best among eight methods in terms of solution quality and running time.
文摘A general mathematical model and boundary condition applicable to momentum and heat transfer in the semisolid continuous casting(SCC) process was established. Using the model, the numerical simulation of the momentum and heat transfer of molten metal was carried out in the SCC system. The obtained results fit well with the measured ones. Moreover, using the numerical simulating software, the effect of various factors on breakout and breakage was explored. The obtained results show that heat flow density of copper mold and the withdrawal beginning time are two major influencing factors. The larger the heat flow density of copper mold, or the shorter the withdrawal beginning time, the more stable the semisolid continuous casting process. [
基金This research was financially supported by National Basic Research Program of China(Grant No.2013CB632203)the Liaoning Provincial Natural Science Foundation of China(Grant No.201202072)+1 种基金National Key Technology R&D Program of China(2012BAF09B01)the Fundamental Research Foundation of Central Universities(Grant Nos.N120509002 and N120309003).
文摘Mg-9Gd-3Y-1.5Zn-0.8Zr alloys own high strength,good heat and corrosion resistance.However,it is difficult for the fabrication of large-scale billets,due to the poor deformation ability and strong hot-crack tendency.This work investigated the casting process on the microstructures and flow stress behaviors of the semi-continuous casting billets for the fabrication of large-scale Mg-9Gd-3Y-1.5Zn-0.8Zr billets.The casting process(electromagnetic intensity and casting speed)shows outstanding effects on the microstructures and flow stress behavior of the billets.The billets with the specific casting process(I=68 A,V=65 mm/min)exhibit uniform microstructures and good deformation uniformity.
基金the National Natural Science Foundation of China(No.U1703131,No.51674027,No.51974027 and No.52004028)Guangdong Basic and Applied Basic Research Foundation(2019A1515111126)the Fundamental Research Funds for the Central Universities(FRF-TP-18-005C1 and FRF-TP-18-041A1).
文摘The two-phase zone continuous casting(TZCC)technique was used to continuously cast high-strength aluminum alloy hollow billets,and a verified 3D model of TZCC was used to simulate the flow and temperature fields at casting speeds of 2-6 mm·min^(-1).Hollow billets under the same conditions were prepared,and their macro/microstructures were analyzed by an optical microscope and a scanning electron microscope.During the TZCC process,a circular fluid flow appears in front of the mushy zone,and the induction heated stepped mold and convective heat transfer result in a curved solidification front with depressed region near the inner wall and a vertical temperature gradient.The deflection of the solidification front decreases and the average cooling rate in the mushy zone increases with increasing casting speed.Experimental results for a 2D12 alloy show that hot tearing periodically appears in the hollow billet accompanied by macrosegregation near the inner wall at casting speeds of 2 and 4 mm·min^(-1),while macroscopic defects of hot tearing and macrosegregation weaken and the average size of columnar crystals in the hollow billets decreases with further increasing casting speed.2D12 aluminum alloy hollow billets with no macroscopic defects,the finest columnar crystals,and excellent mechanical properties were prepared by TZCC at a casting speed of 6 mm·min^(-1),which is beneficial for the further plastic forming process.
文摘Understanding the transformation of liquid steel to solid steel is the most fundamental aspect of continuous casting;however,it remains a complex subject with a number of unresolved issues.In this paper,the following aspects of mold operation which give rise to sub-surface defects will be discussed;meniscus solidification,surface and interfacial energies,effects of gas bubbles,and the dynamic nature of the liquid slag-liquid steel interface.
基金Key Project of Shandong Provincial Natural Science Foundation,China(No.ZR2010FZ001)National High-Tech Research and Development Program of China(863 Program)(No.2007AA04Z157)
文摘A matrix encoding scheme for the steelmaking continuous casting( SCC) production scheduling( SCCPS) problem and the corresponding decoding method are proposed. Based on it,a cross entropy( CE) method is adopted and an improved cross entropy( ICE) algorithm is proposed to solve the SCCPS problem to minimize total power consumption. To describe the distribution of the solution space of the CE method,a probability model is built and used to generate individuals by sampling and a probability updating mechanism is introduced to trace the promising samples. For the ICE algorithm,some samples are generated by the heuristic rules for the shortest makespan due to the relation between the makespan and the total power consumption,which can reduce the search space greatly. The optimal sample in each iteration is retained through a retention mechanism to ensure that the historical optimal sample is not lost so as to improve the efficiency and global convergence. A local search procedure is carried out on a part of better samples so as to improve the local exploitation capability of the ICE algorithm and get a better result. The parameter setting is investigated by the Taguchi method of design-of-experiment. A number of simulation experiments are implemented to validate the effectiveness of the ICE algorithm in solving the SCCPS problem and also the superiority of the ICE algorithm is verified through the comparison with the standard cross entropy( SCE) algorithm.
基金financially supported by the National Natural Science Foundation of China(51932008 and 51772277)Zhongyuan Science and Technology Innovation Leader(204200510011)
文摘The causes, the formation process, and the prevention of submerged entry nozzle(SEN) clogging were introduced. The influence of electric field on the SEN clogging was focused on, including the basic theory and measurement of SEN charging,the preliminary research on SEN charging, the influence of molten steel on the wetting behavior of refractory materials in electric field, and the influence of electric field on the oxide inclusions in molten steel. Based on the influence of the hydrodynamics, chemistry and other factors on refractory materials, structure, inclusion particle transfer and adhesion, many anti-clogging researches have been carried out, such as optimizing process conditions, compositing anti-clogging inner lining materials, innovating SEN structure and applying physical fields, which solve the problem of SEN clogging to a certain extent.However, the problems of weak adaptability and superficial study on clogging mechanism are still prominent. The electric field control is a new technology to prevent clogging. Although it has achieved certain results in on-site continuous casting trials,some problems such as the method of applying electric field, the electric field parameters and the equipment still need to be gradually improved, and the surface characteristics of inclusions and SEN materials at high temperatures need to be further studied. It was pointed out that the combination of materials and applied electric field will become an important direction for SEN anti-clogging technology.
文摘A mold flux is widely used to modify heat transfer rates in continuous casting,and crystallization of the mold flux has been identified as a primary factor that influences heat flux from the strand to the mold.As the harsh environment and the very high transient nature of the mold caster,the study of dynamic mold flux melting and crystallization as well as their effects on heat transfer has not been conducted widely.By using an infrared radiation emitter,a high level heat flux was applied to a copper mold covered with solid mold flux disk to simulate the heat transfer phenomena in continuous casting.By this technique it is possible to have a liquid layer,a crystalline layer and a glassy layer in contact with one another and,by varying the energy input,it is possible to study the dynamic nature of the film and its effect on the heat transfer rate.A general heat transfer model was also developed to allow the prediction of the effect of varying the thickness of the three potential layers in the flux film.
