Extensive studies based on partition curve of gravity separation have been investigated. All created models are merely used to simulate density distribution at the same size fraction. However, they cannot be used to p...Extensive studies based on partition curve of gravity separation have been investigated. All created models are merely used to simulate density distribution at the same size fraction. However, they cannot be used to predictive distribution of materials depending on compound feature of density and size. According to this situation, an improved model of partition curve based on accumulation normal distribution, which was distinguished from conventional model of accumulation normal distribution for partition curve, was proposed in this paper. It could simulate density distribution at different size fractions by using the density-size compound index and conflating the partition curves at different size fractions as one partition curve. The feasibility of three compound indexes, including mass index, settlement index and transformation index, were investigated. Specific forms of the improved model were also proposed. It is found that transformation index leads to the best fitting results, while the fitting error is only 1.75 according to the fitting partition curve.展开更多
Rocky landslides on river banks can result in the generation of ultra-high waves,which may destroy structures on the opposite bank.Existing methods to calculate the pressure on bank slopes under the effect of impulse ...Rocky landslides on river banks can result in the generation of ultra-high waves,which may destroy structures on the opposite bank.Existing methods to calculate the pressure on bank slopes under the effect of impulse waves generated by landslides are,however,few and of low precision.Therefore,in this study,a three-dimensional physical model test was conducted by taking into account factors such as landslide geometry parameters and the bank slope angle.The model test section was generalized on the basis of a certain section of the Three Gorges reservoir area as a prototype,after which the wave parameters and wave pressure acting on the bank slope were measured.Subsequently,the magnitude,acting point,and distribution of the pressure of the impulse waves generated by the rocky landslide upon the bank slope were determined.The distribution curve of the impact pressure was similar to that calculated using theСНиПⅡ57-75 formula,and the experimental pulsating pressure value was close to the value calculated using the Subgrade formula.Based on the test results,a power function of the relative pulsating pressure steepness with respect to the reciprocal of the wave steepness,relative water depth,and slope ratio was proposed.The acting point of the maximum pulsating pressure was found to be located near the still water level.Finally,an empirical formula for calculating the envelope of the maximum pulsating pressure distribution curve was proposed.These formulas can serve as a theoretical basis for the prediction of impulse wave pressure generated owing to landslides on bank slopes.展开更多
Aiming at the problem that the existence of inclusions in the tundish continuous casting process can easily lead to quality defects of the slab,the stainless steel continuous casting tundish was taken as the research ...Aiming at the problem that the existence of inclusions in the tundish continuous casting process can easily lead to quality defects of the slab,the stainless steel continuous casting tundish was taken as the research object.The effects of flow control device,inclusion density and inclusion size on the mixing characteristics of molten steel and inclusion behavior in tundish were studied.The results showed that compared with the tundish without flow control device,the average residence time of molten steel was prolonged by about 49 s,the dead zone volume fraction was reduced by 8.93%,and the piston fluid integral rate was increased by 12.68%.In the turbulence inhibitor(TI)tundish with weir-dam combination,the removal rate of inclusions with a density of 2700 kg m^(-3) and a particle size of 5 lm is 63.32%,while the removal rate of large inclusions with a density of 150μm could reach 89.04%.When the inclusion particle size was 10-50μm and the density was 2700-4500 kg m^(-3),the effect of inclusion density on inclusion removal rate was small.At the same time,when weir-dam combination TI tundish was set,the inclusions were mainly limited to the slag-metal interface of the first and second chambers of the tundish.The removal rate of inclusions in the first chamber was generally improved,with 10μm inclusions accounting for 47.67% and 150μm inclusions accounting for 60.69%.Furthermore,it has the best effect on the removal of small-size inclusions,especially those less than 70μm.展开更多
The flow-field index in a 41-ton six-strand tundish is considered through adjusting the ratio of the casting velocity between the strands to eliminate the negative impact of iso-velocity casting in multi-strand tundis...The flow-field index in a 41-ton six-strand tundish is considered through adjusting the ratio of the casting velocity between the strands to eliminate the negative impact of iso-velocity casting in multi-strand tundish on the consistency of each strand due to the large ratio of length to width with narrow shape structure,resulting in poor consistency of each strand.In particular,the response time of strand-1 and strand-6 is relatively long,which affects the uniformity of the temperature field and flow field of the entire tundish.On the basis of verifying that the error between the numerical simulations and hydraulic experiments is less than 6%,six cases with the casting velocity ratio changing from 0.8 to 1.3(with an interval of 0.1)are considered by calculation of numerical models.It is concluded that the consistency of each flow can be obviously improved by increasing the casting velocity ratio between side-strand and middle-strand.With increasing the casting velocity ratio,the flow field in the tundish became much active,the temperature field presented well uniformity,and the tracer concentration distribution in local dead zones was improved.展开更多
基金the financial support from the National Natural Science Foundation of China (No. 51221462)
文摘Extensive studies based on partition curve of gravity separation have been investigated. All created models are merely used to simulate density distribution at the same size fraction. However, they cannot be used to predictive distribution of materials depending on compound feature of density and size. According to this situation, an improved model of partition curve based on accumulation normal distribution, which was distinguished from conventional model of accumulation normal distribution for partition curve, was proposed in this paper. It could simulate density distribution at different size fractions by using the density-size compound index and conflating the partition curves at different size fractions as one partition curve. The feasibility of three compound indexes, including mass index, settlement index and transformation index, were investigated. Specific forms of the improved model were also proposed. It is found that transformation index leads to the best fitting results, while the fitting error is only 1.75 according to the fitting partition curve.
基金financial support from the National Natural Science Foundation of China(Grant No.51479015)the Chongqing Research Program of Basic Research and Frontier Technology(Grant No.cstc2017 jcyj BX0070)+6 种基金the Chongqing Science and Technology Commission of China(Grant No.cstc2017jcyj A1642)the Technology innovation and application demonstration project in Chongqing(Grant No.cstc2018jscx-msyb0328)the Chongqing,the Chongqing Municipal Education Commission of China(Grant No.KJ1705123)the China Postdoctoral Science Foundation funded project(Grant No.2019M663890XB)Chongqing Postdoctoral Science Foundation funded project(Grant No.228512)Chongqing Municipal Education Commission Effects of Global Warming on Extreme Weather Events in Chongqing(Grant No.KJQN201800711)Chongqing Municipal Education Commission Project(Grant No.KJQN202000747)。
文摘Rocky landslides on river banks can result in the generation of ultra-high waves,which may destroy structures on the opposite bank.Existing methods to calculate the pressure on bank slopes under the effect of impulse waves generated by landslides are,however,few and of low precision.Therefore,in this study,a three-dimensional physical model test was conducted by taking into account factors such as landslide geometry parameters and the bank slope angle.The model test section was generalized on the basis of a certain section of the Three Gorges reservoir area as a prototype,after which the wave parameters and wave pressure acting on the bank slope were measured.Subsequently,the magnitude,acting point,and distribution of the pressure of the impulse waves generated by the rocky landslide upon the bank slope were determined.The distribution curve of the impact pressure was similar to that calculated using theСНиПⅡ57-75 formula,and the experimental pulsating pressure value was close to the value calculated using the Subgrade formula.Based on the test results,a power function of the relative pulsating pressure steepness with respect to the reciprocal of the wave steepness,relative water depth,and slope ratio was proposed.The acting point of the maximum pulsating pressure was found to be located near the still water level.Finally,an empirical formula for calculating the envelope of the maximum pulsating pressure distribution curve was proposed.These formulas can serve as a theoretical basis for the prediction of impulse wave pressure generated owing to landslides on bank slopes.
基金financially supported by the National Natural Science Foundation of China(Nos.52174321,51874203 and 52074186).
文摘Aiming at the problem that the existence of inclusions in the tundish continuous casting process can easily lead to quality defects of the slab,the stainless steel continuous casting tundish was taken as the research object.The effects of flow control device,inclusion density and inclusion size on the mixing characteristics of molten steel and inclusion behavior in tundish were studied.The results showed that compared with the tundish without flow control device,the average residence time of molten steel was prolonged by about 49 s,the dead zone volume fraction was reduced by 8.93%,and the piston fluid integral rate was increased by 12.68%.In the turbulence inhibitor(TI)tundish with weir-dam combination,the removal rate of inclusions with a density of 2700 kg m^(-3) and a particle size of 5 lm is 63.32%,while the removal rate of large inclusions with a density of 150μm could reach 89.04%.When the inclusion particle size was 10-50μm and the density was 2700-4500 kg m^(-3),the effect of inclusion density on inclusion removal rate was small.At the same time,when weir-dam combination TI tundish was set,the inclusions were mainly limited to the slag-metal interface of the first and second chambers of the tundish.The removal rate of inclusions in the first chamber was generally improved,with 10μm inclusions accounting for 47.67% and 150μm inclusions accounting for 60.69%.Furthermore,it has the best effect on the removal of small-size inclusions,especially those less than 70μm.
基金supported by the National Natural Science Foundation of China (Grant Number51774031)the State Key Laboratory of Advanced Metallurgy Foundation (Grant Number 41619018)。
文摘The flow-field index in a 41-ton six-strand tundish is considered through adjusting the ratio of the casting velocity between the strands to eliminate the negative impact of iso-velocity casting in multi-strand tundish on the consistency of each strand due to the large ratio of length to width with narrow shape structure,resulting in poor consistency of each strand.In particular,the response time of strand-1 and strand-6 is relatively long,which affects the uniformity of the temperature field and flow field of the entire tundish.On the basis of verifying that the error between the numerical simulations and hydraulic experiments is less than 6%,six cases with the casting velocity ratio changing from 0.8 to 1.3(with an interval of 0.1)are considered by calculation of numerical models.It is concluded that the consistency of each flow can be obviously improved by increasing the casting velocity ratio between side-strand and middle-strand.With increasing the casting velocity ratio,the flow field in the tundish became much active,the temperature field presented well uniformity,and the tracer concentration distribution in local dead zones was improved.
