The electromagnetic induction method is widely used to measure sea ice thickness. Based on the electrical properties of sea ice and seawater, the method measures the apparent conductivity, which represents the conduct...The electromagnetic induction method is widely used to measure sea ice thickness. Based on the electrical properties of sea ice and seawater, the method measures the apparent conductivity, which represents the conductivity of the half-space, and calculates the thickness of the sea ice. During the fourth Chinese National Arctic Research Expedition in summer 2010, an integrated electromagnetic induction system was set up on the icebreaker R/V XUE LONG to measure sea ice thickness along the ship's tracks to the north of the Chukchi Sea. The conductivities of sea ice, seawater, and brine were measured and a simple forward model was used to explain the effect of changes in those conductivities on the apparent conductivity over a horizontal layered structure. The results of this analysis indicated that when using the electromagnetic induction method to measure sea ice thickness, the conductivity of sea ice could be neglected and the conductivity of seawater could be treated as a constant. The ice distribution results derived from the electromagnetic induction method showed that the typical sea ice thickness was 160 cm and 90 cm during the outbound and the return legs of the voyage, respectively.展开更多
The dual transmitter implements the equivalent anti-magnetic flux transient electromagnetic method, which can effectively reduce the scope of the transient electromagnetic detection blind area. However, this method is...The dual transmitter implements the equivalent anti-magnetic flux transient electromagnetic method, which can effectively reduce the scope of the transient electromagnetic detection blind area. However, this method is rarely reported in the detection of pipelines in urban geophysical exploration and the application of coal mines. Based on this, this paper realizes the equivalent anti-magnetic flux transient electromagnetic method based on the dual launcher. The suppression effect of this method on the blind area is analyzed by physical simulation. And the detection experiment of underground pipelines is carried out outdoors. The results show that the dual launcher can significantly reduce the turn-off time, thereby effectively reducing the impact of the blind area on the detection results, and the pipeline detection results verify the device’s effectiveness. Finally, based on the ground experimental results, the application prospect of mine advanced detection is discussed. Compared with other detection fields, the formation of blind areas is mainly caused by the equipment. If the dual launcher can be used to reduce the blind area, the accuracy of advanced detection can be improved more effectively. The above research results are of great significance for improving the detection accuracy of the underground transient electromagnetic method.展开更多
Global electromagnetic induction provides an efficient way to probe the electrical conductivity in the Earth’s deep interior.Owing to the increasing geomagnetic data especially from high-accuracy geomagnetic satellit...Global electromagnetic induction provides an efficient way to probe the electrical conductivity in the Earth’s deep interior.Owing to the increasing geomagnetic data especially from high-accuracy geomagnetic satellites,inverting the Earth’s three-dimensional conductivity distribution on a global scale becomes attainable.A key requirement in the global conductivity inversion is to have a forward solver with high-accuracy and efficiency.In this study,a finite volume method for global electromagnetic induction forward modeling is developed based on unstructured grids.Arbitrary polyhedral grids are supported in our algorithms to obtain high geometric adaptability.We employ a cell-centered collocated variable arrangement which allows convenient discretization for complex geometries and straightforward implementation of multigrid technique.To validate the method,we test our code with two synthetic models and compare our finite volume results with an analytical solution and a finite element numerical solution.Good agreements are observed between our solution and other results,indicating acceptable accuracy of the proposed method.展开更多
Epilepsy is believed to be associated with the abnormal synchronous neuronal activity in the brain,which results from large groups or circuits of neurons.In this paper,we choose to focus on the temporal lobe epilepsy,...Epilepsy is believed to be associated with the abnormal synchronous neuronal activity in the brain,which results from large groups or circuits of neurons.In this paper,we choose to focus on the temporal lobe epilepsy,and establish a cortex network of multiple coupled neural populations to explore the epileptic activities under electromagnetic induction.We demonstrate that the epileptic activities can be controlled and modulated by electromagnetic induction and coupling among regions.In certain regions,these two types of control are observed to show exactly reverse effects.The results show that the strong electromagnetic induction is conducive to eliminating the epileptic seizures.The coupling among regions has a conduction effect that the previous normal background activity of the region gives way to the epileptic discharge,owing to coupling with spike wave discharge regions.Overall,these results highlight the role of electromagnetic induction and coupling among the regions in controlling and modulating epileptic activities,and might provide novel insights into the treatments of epilepsy.展开更多
An analytic electromagnetic calculation method for doubly fed induction generator(DFIG) in wind turbine system was presented. Based on the operation principles, steady state equivalent circuit and basic equations of D...An analytic electromagnetic calculation method for doubly fed induction generator(DFIG) in wind turbine system was presented. Based on the operation principles, steady state equivalent circuit and basic equations of DFIG, the modeling for electromagnetic calculation of DFIG was proposed. The electromagnetic calculation of DFIG was divided into three steps: the magnetic flux calculation, parameters derivation and performance checks. For each step, the detailed numeric calculation formulas were all derived. Combining the calculation formulas, the whole electromagnetic calculation procedure was established, which consisted of three iterative calculation loops, including magnetic saturation coefficient, electromotive force and total output power. All of the electromagnetic and performance data of DIFG can be calculated conveniently by the established calculation procedure, which can be used to evaluate the new designed machine. A 1.5 MW DFIG designed by the proposed procedure was built, for which the whole type tests including no-load test, load test and temperature rising test were carried out. The test results have shown that the DFIG satisfies technical requirements and the test data fit well with the calculation results which prove the correctness of the presented calculation method.展开更多
In recent years,karst construction projects in the built-up area of Wuhan(capital of Hubei Province,China)are increasing,and the karst geological disasters have aroused social concerns.The actual engineering projects ...In recent years,karst construction projects in the built-up area of Wuhan(capital of Hubei Province,China)are increasing,and the karst geological disasters have aroused social concerns.The actual engineering projects usually use shallow geophysical exploration methods to explore karst.This paper uses Spatial Auto-Correlation Method(SPAC)and electromagnetic Computerized Tomography(CT)to detect karst in urban built-up areas.Depending on the different physical properties of rock and soil,the SPAC method can better reveal the interface between soil and rock strata and the interface between soil layers.The electromagnetic CT method can identify strata according to the apparent absorption coefficient,which can better reveal the interface between soil and rock,the interface between the more intact and weathered rock.The SPAC method is mainly qualitative to measure the low-speed area,namely,the wrong geological body i.e.,karst cave,but also can detect the fracture zone or filling mode of karst cave,and at the same time,cannot use exploration holes or logging observation.The electromagnetic CT method can accurately detect the location and scale of the karst caves and has a higher accuracy detecting karst bands.In addition,exploration holes or well logging observations are also expected to be conducted,and their detection effect is greatly affected by lithology.展开更多
This study used the stable and convergent Dufort-Frankel method to differentially discretize the diffusion equation of the ground-well transient electromagnetic secondary field.The absorption boundary condition of com...This study used the stable and convergent Dufort-Frankel method to differentially discretize the diffusion equation of the ground-well transient electromagnetic secondary field.The absorption boundary condition of complex frequency-shifted perfectly matched layer(CFS-PML)was used for truncation so that the low-frequency electromagnetic wave can be better absorbed at the model boundary.A typical three-dimensional(3D)homogeneous half-space model was established and a low-resistivity cube model was analyzed under the half-space condition.The response patterns and drivers of the low-resistivity cube model were discussed under the influence of a low-resistivity overburden.The absorption boundary conditions of CFS-PML significantly affected the low-frequency electromagnetic waves.For a low-resistivity cube around the borehole,its response curve exhibited a single-peak,and the extreme point of the curve corresponded to the center of the low-resistivity body.When the low-resistivity cube was directly below the borehole,the response curve showed three extreme values(two high and one low),with the low corresponding to the center of the low-resistivity body.The total field response of the low-resistivity overburden was stronger than that of the uniform half-space model due to the low-resistivity shielding effect of electromagnetic waves.When the receiving-transmitting distance gradually increased,the effect of the low-resistivity overburden was gradually weakened,and the response of the low-resistivity cube was strengthened.It was affected by the ratio of the overburden resistivity to the resistivity of the low-resistivity body.展开更多
Electricity and magnetism and electromagnetic induction are phenomena that can be perceived by people. But their interpretation and theoretical study took a long time. The theoretical research on electricity began wit...Electricity and magnetism and electromagnetic induction are phenomena that can be perceived by people. But their interpretation and theoretical study took a long time. The theoretical research on electricity began with the discovery of Coulomb’s law in 1785, while the theoretical research on magnetism began with the discovery of Oersted’s Law in 1820. From the 1850s to the 1870s, Maxwell summarized a set of theoretical equations for electromagnetism based on some laws of predecessors. However, this set of equations contains a few statistical relationships and empirical concepts, so it is difficult to explain the physical nature of electromagnetic phenomena and principles. This paper explained that the macro phenomenon of electricity is the separation of unlike charges of new electrons produced by the orthogonal collision of old particles under the action of external forces. The physical nature of magnetism is the potential energy (magnetic energy) and information associated with the overall orientation of the moving electrons solidly recorded in the material. The physical principle of electromagnetic induction describes how change in electric current intensity generates change in magnetic intensity and vice versa through orthogonal interaction of ordered electrons. This theoretical interpretation does not require the concepts of traditional electromagnetic forces, electromagnetic fields, magnetic moments, and magnetic domains.展开更多
Recent decades have seen rapid advances in the field of electrical engineering, such that our environment has become a sea of electrical and magnetic signals, raising questions about the possible effects of low-freque...Recent decades have seen rapid advances in the field of electrical engineering, such that our environment has become a sea of electrical and magnetic signals, raising questions about the possible effects of low-frequency electromagnetic fields on the environment and which are capable of modifying and destroying our ecosystem. Particular interest was given in this article due to a massive influx of population living near high voltage lines. The analysis and simulation of the influence of low frequency electromagnetic fields on living beings in the vicinity of high voltage sources 132 kV and 220 kV in urban areas in DR Congo is the subject of our research with a view to estimating the level of exposure of humans to low frequency electromagnetic fields. To carry out our research, we used the classic method of analyzing the field produced near a high voltage line based on Maxwell’s image theory, the Maxwell-Gauss theorem and Maxwell-Ampère theorem to model and quantify low-frequency electromagnetic fields in the vicinity of high-voltage lines. The 2D FDTD numerical formulation was developed from telegraphers’ equations and allowed us to obtain models of current and voltage induced by electromagnetic fields on living beings below and near HV lines. The different simulations carried out on the proposed models illustrate the effects of the electrical and geometric parameters of the pylons on the distribution of the electromagnetic field in the vicinity of the HV lines. The results obtained were compared to the safety limits recommended by the standards.展开更多
The signs of the electric field markers in Figs.2 and 4 of the paper[Chin.Phys.B 32104211(2023)]have been corrected.These modifications do not affect the results derived in the paper.
The research about subsurface characteristics by using transient electromagnetic method(TEM) and high density resistivity method(HDRM) were already conducted in Ordos. The objective of this research is to detect coalm...The research about subsurface characteristics by using transient electromagnetic method(TEM) and high density resistivity method(HDRM) were already conducted in Ordos. The objective of this research is to detect coalmine goaf areas based on rock resistivity. The data processing using wavelet transform, three point smoothing, RES2 DINV and Maxwell processing software to obtain 2D resistivity structure. The results showed that the layers with maximum resistivity values(30e33 U m on Line 1, 30e31 U m on Line 2, 32e40 U m on Line3) are founded at station 1e7, and 14e20 on Line 1,13e18 on Line 2, and 8e13 and 16e20 on Line 3 which is predicted as goaf layer, and the minimum resistivity values(20e26 U m of TEM, 45e75 U m of HDRM) at the other layers. This resistivity difference was caused by the geology and characteristics of the study area which is located close by the cleugh with rich coal, so the goaf area distinguishable with aquifer layer and coal seam. The results were also significant accidents and serious destruction of ecological environment.展开更多
Current research in broken rotor bar(BRB) fault detection in induction motors is primarily focused on a high-frequency resolution analysis of the stator current.Compared with a discrete Fourier transformation, the par...Current research in broken rotor bar(BRB) fault detection in induction motors is primarily focused on a high-frequency resolution analysis of the stator current.Compared with a discrete Fourier transformation, the parametric spectrum estimation technique has a higher frequency accuracy and resolution. However, the existing detection methods based on parametric spectrum estimation cannot realize online detection, owing to the large computational cost. To improve the efficiency of BRB fault detection,a new detection method based on the min-norm algorithm and least square estimation is proposed in this paper. First, the stator current is filtered using a band-pass filter and divided into short overlapped data windows. The min-norm algorithm is then applied to determine the frequencies of the fundamental and fault characteristic components with each overlapped data window. Next, based on the frequency values obtained, a model of the fault current signal is constructed. Subsequently, a linear least squares problem solved through singular value decomposition is designed to estimate the amplitudes and phases of the related components. Finally,the proposed method is applied to a simulated current and an actual motor,the results of which indicate that, not only parametric spectrum estimation technique.展开更多
This paper proposes an effective method for early diagnosis (stress concentrating) of the oil-gas pipeline. Based on the principle of electromagnetic induction Faraday, we have designed and realized the nondestructive...This paper proposes an effective method for early diagnosis (stress concentrating) of the oil-gas pipeline. Based on the principle of electromagnetic induction Faraday, we have designed and realized the nondestructive testing system for stress concentration area of ferromagnetic materials by means of the research of metal materials inverse magnetostrictive effect mechanism. The system changes the influence degree of the stress in ferromagnetic materials’ magnetic conductance to the corresponding voltage array by using discrete wavelet analysis method to process the data, in which not only the measuring accuracy is improved, but also the stress concentration is more directly reflected. The experiments confirm that the electromagnetic stress testing method is feasible and valid.展开更多
The paper presents a mathematical multibody model of a soft mounted induction motor with sleeve bearings regarding forced vibrations caused by dynamic rotor eccentricities considering electromagnetic field damping. Th...The paper presents a mathematical multibody model of a soft mounted induction motor with sleeve bearings regarding forced vibrations caused by dynamic rotor eccentricities considering electromagnetic field damping. The multibody model contains the mass of the stator, rotor, shaft journals and bearing housings, the electromagnetic forces with respect of electromagnetic field damping, stiffness and internal (rotating) damping of the rotor, different kinds of dynamic rotor eccentricity, stiffness and damping of the bearing housings and end shields, stiffness and damping of the oil film of the sleeve bearings and stiffness and damping of the foundation. With this multibody model, the bearing housing vibrations and the relative shaft vibrations in the sleeve bearings can be derived.展开更多
We discuss a thermoelectric energy generation (TEG) technique by employing a thermomechanical model of a drinking bird (DB). The motion of a drinking bird is produced by the entropy-flow explained by the second law of...We discuss a thermoelectric energy generation (TEG) technique by employing a thermomechanical model of a drinking bird (DB). The motion of a drinking bird is produced by the entropy-flow explained by the second law of thermodynamics, which is one of the fundamental laws of heat engines. We propose a disk-magnet electromagnetic induction (DM-EMI) employed to the motion of a drinking bird. The generalization of DM-EMI to heat engines for?mechanoelectric?energy conversions and properties of extracted electric powers are specifically discussed. The electric power of DM-EMI has a limited power generation characteristic to a mechanical rotation produced by heat engines, but it will be very useful for practical applications to wind turbines, coal-fired and nuclear power plant for?mechanoelectric?energy conversions. The DM-EMI will contribute to environmental problems to maintain clean and susceptible energy as one of?energy?harvesting technologies.展开更多
The finite volume time domain(FVTD) algorithm and Green function algorithm are extended to Schwarzschild spacetime for numerical simulation of electromagnetic scattering. The FVTD method in Schwarzschild spacetime is ...The finite volume time domain(FVTD) algorithm and Green function algorithm are extended to Schwarzschild spacetime for numerical simulation of electromagnetic scattering. The FVTD method in Schwarzschild spacetime is developed by filling the flat spacetime with an equivalent medium. The Green function in Schwarzschild spacetime is acquired by solving initial value problems. Both the FVTD code and the Green function code are validated by numerical results. Scattering in Schwarzschild spacetime is simulated with these methods.展开更多
In recent years,in order to meet the practical needs of deep edge mine detection with large depth and high precision,transient electromagnetic method(TEM)near emission source detection mode has become an international...In recent years,in order to meet the practical needs of deep edge mine detection with large depth and high precision,transient electromagnetic method(TEM)near emission source detection mode has become an international advanced method(Xue et al.,2020).展开更多
Voltage sag is one of the most common power quality disturbances in industry,which causes huge inrush currents in stator windings of induction motors,and adversely impacts the motor secure operation.This paper firstly...Voltage sag is one of the most common power quality disturbances in industry,which causes huge inrush currents in stator windings of induction motors,and adversely impacts the motor secure operation.This paper firstly introduces a 2D Time-Stepping multi-slice finite element method(2D T-S multi-slice FEM)which is used for calculating the magnetic field distribution in induction motors under different sag events.Then the paper deduces the transient analytical expression of stator inrush current based on the classical theory of AC motors and presents a separation method for the positive,negative and zero sequence values based on instantaneous currents.With this method,the paper studies the influences of voltage sag amplitude,phase-angle jump and initial phase angle on the stator positive-and negative-sequence peak currents of 5.5 kW and 55 kW induction motors.This paper further proposes a motor protection method under voltage sag condition with the stator negative-sequence peak currents as the protection threshold,so that the protection false trip can be avoided effectively.Finally,the calculation and analysis results are validated by the comparison of calculated and measured stator peak value of the 5.5 kW induction motor.展开更多
A kind of signal acquisition circuit and the related signal processing method of the capacitanceelectromagnetic flowmeter (EMF) were introduced. The circuit can eliminate the influence of distributed capacitanceon the...A kind of signal acquisition circuit and the related signal processing method of the capacitanceelectromagnetic flowmeter (EMF) were introduced. The circuit can eliminate the influence of distributed capacitanceon the input impedance of the operational amplifier, and greatly improve the input impedance of the detection circuitto overcome the disadvantage of high signal source impedance. The rotating capacitor filter is a signal processingmethod based on the phase-sensitive detection technology. It can extract the weak signal from the strong and widebandbackground noise, so it is very suitable for the processing of capacitive electromagnetic flow signals. Throughthe comparison of the signal amplitude obtained at different flow rates and the comparison of signal spectrumcomponents before and after the filter, the effectiveness of the bootstrap signal acquisition circuit and rotatingcapacitor filtering method is verified.展开更多
基金supported by the National Natural Science Foundation of China(Grant no.41006116)the National Major Scientific Research Project(Grant no.2013CBA01804)the Chinese Polar Environmental Comprehensive Investigation and Assessment Programs(Grant no.CHINARE-2015-02-02)
文摘The electromagnetic induction method is widely used to measure sea ice thickness. Based on the electrical properties of sea ice and seawater, the method measures the apparent conductivity, which represents the conductivity of the half-space, and calculates the thickness of the sea ice. During the fourth Chinese National Arctic Research Expedition in summer 2010, an integrated electromagnetic induction system was set up on the icebreaker R/V XUE LONG to measure sea ice thickness along the ship's tracks to the north of the Chukchi Sea. The conductivities of sea ice, seawater, and brine were measured and a simple forward model was used to explain the effect of changes in those conductivities on the apparent conductivity over a horizontal layered structure. The results of this analysis indicated that when using the electromagnetic induction method to measure sea ice thickness, the conductivity of sea ice could be neglected and the conductivity of seawater could be treated as a constant. The ice distribution results derived from the electromagnetic induction method showed that the typical sea ice thickness was 160 cm and 90 cm during the outbound and the return legs of the voyage, respectively.
文摘The dual transmitter implements the equivalent anti-magnetic flux transient electromagnetic method, which can effectively reduce the scope of the transient electromagnetic detection blind area. However, this method is rarely reported in the detection of pipelines in urban geophysical exploration and the application of coal mines. Based on this, this paper realizes the equivalent anti-magnetic flux transient electromagnetic method based on the dual launcher. The suppression effect of this method on the blind area is analyzed by physical simulation. And the detection experiment of underground pipelines is carried out outdoors. The results show that the dual launcher can significantly reduce the turn-off time, thereby effectively reducing the impact of the blind area on the detection results, and the pipeline detection results verify the device’s effectiveness. Finally, based on the ground experimental results, the application prospect of mine advanced detection is discussed. Compared with other detection fields, the formation of blind areas is mainly caused by the equipment. If the dual launcher can be used to reduce the blind area, the accuracy of advanced detection can be improved more effectively. The above research results are of great significance for improving the detection accuracy of the underground transient electromagnetic method.
基金supported by the National Natural Science Foundation of China(41922027,4214200052)by the Macao Foundation+1 种基金by the Pre-research Project on Civil Aerospace Technologies No.D020308/D020303 funded by China National Space Administrationby the Macao Science and Technology Development Fund,grant No.0001/2019/A1。
文摘Global electromagnetic induction provides an efficient way to probe the electrical conductivity in the Earth’s deep interior.Owing to the increasing geomagnetic data especially from high-accuracy geomagnetic satellites,inverting the Earth’s three-dimensional conductivity distribution on a global scale becomes attainable.A key requirement in the global conductivity inversion is to have a forward solver with high-accuracy and efficiency.In this study,a finite volume method for global electromagnetic induction forward modeling is developed based on unstructured grids.Arbitrary polyhedral grids are supported in our algorithms to obtain high geometric adaptability.We employ a cell-centered collocated variable arrangement which allows convenient discretization for complex geometries and straightforward implementation of multigrid technique.To validate the method,we test our code with two synthetic models and compare our finite volume results with an analytical solution and a finite element numerical solution.Good agreements are observed between our solution and other results,indicating acceptable accuracy of the proposed method.
基金Project supported by the National Natural Science Foundation of China(Nos.11772254 and 11972288)the Innovation Foundation for Doctor Dissertation of Northwestern Polytechnical University of China(No.CX2021106)。
文摘Epilepsy is believed to be associated with the abnormal synchronous neuronal activity in the brain,which results from large groups or circuits of neurons.In this paper,we choose to focus on the temporal lobe epilepsy,and establish a cortex network of multiple coupled neural populations to explore the epileptic activities under electromagnetic induction.We demonstrate that the epileptic activities can be controlled and modulated by electromagnetic induction and coupling among regions.In certain regions,these two types of control are observed to show exactly reverse effects.The results show that the strong electromagnetic induction is conducive to eliminating the epileptic seizures.The coupling among regions has a conduction effect that the previous normal background activity of the region gives way to the epileptic discharge,owing to coupling with spike wave discharge regions.Overall,these results highlight the role of electromagnetic induction and coupling among the regions in controlling and modulating epileptic activities,and might provide novel insights into the treatments of epilepsy.
基金Project(2011DFA62240) supported by the International Scientific and Technological Cooperation Projects,ChinaProject(019945-SES6) supported by the European Union(EU)6th Framework Program UP-WIND Project,Denmark
文摘An analytic electromagnetic calculation method for doubly fed induction generator(DFIG) in wind turbine system was presented. Based on the operation principles, steady state equivalent circuit and basic equations of DFIG, the modeling for electromagnetic calculation of DFIG was proposed. The electromagnetic calculation of DFIG was divided into three steps: the magnetic flux calculation, parameters derivation and performance checks. For each step, the detailed numeric calculation formulas were all derived. Combining the calculation formulas, the whole electromagnetic calculation procedure was established, which consisted of three iterative calculation loops, including magnetic saturation coefficient, electromotive force and total output power. All of the electromagnetic and performance data of DIFG can be calculated conveniently by the established calculation procedure, which can be used to evaluate the new designed machine. A 1.5 MW DFIG designed by the proposed procedure was built, for which the whole type tests including no-load test, load test and temperature rising test were carried out. The test results have shown that the DFIG satisfies technical requirements and the test data fit well with the calculation results which prove the correctness of the presented calculation method.
文摘In recent years,karst construction projects in the built-up area of Wuhan(capital of Hubei Province,China)are increasing,and the karst geological disasters have aroused social concerns.The actual engineering projects usually use shallow geophysical exploration methods to explore karst.This paper uses Spatial Auto-Correlation Method(SPAC)and electromagnetic Computerized Tomography(CT)to detect karst in urban built-up areas.Depending on the different physical properties of rock and soil,the SPAC method can better reveal the interface between soil and rock strata and the interface between soil layers.The electromagnetic CT method can identify strata according to the apparent absorption coefficient,which can better reveal the interface between soil and rock,the interface between the more intact and weathered rock.The SPAC method is mainly qualitative to measure the low-speed area,namely,the wrong geological body i.e.,karst cave,but also can detect the fracture zone or filling mode of karst cave,and at the same time,cannot use exploration holes or logging observation.The electromagnetic CT method can accurately detect the location and scale of the karst caves and has a higher accuracy detecting karst bands.In addition,exploration holes or well logging observations are also expected to be conducted,and their detection effect is greatly affected by lithology.
基金This work was supported by China Postdoctoral Science Foundation(No.2022M723391)the Science and Technology Innovation Project of Higher Education in Shanxi Province(No.2019L0754)+1 种基金the Central Guiding Local Science and Technology Development Fund Project(No.YDZJSX2021B021)Shanxi Province Basic Research Plan General Project(No.202203021221294).
文摘This study used the stable and convergent Dufort-Frankel method to differentially discretize the diffusion equation of the ground-well transient electromagnetic secondary field.The absorption boundary condition of complex frequency-shifted perfectly matched layer(CFS-PML)was used for truncation so that the low-frequency electromagnetic wave can be better absorbed at the model boundary.A typical three-dimensional(3D)homogeneous half-space model was established and a low-resistivity cube model was analyzed under the half-space condition.The response patterns and drivers of the low-resistivity cube model were discussed under the influence of a low-resistivity overburden.The absorption boundary conditions of CFS-PML significantly affected the low-frequency electromagnetic waves.For a low-resistivity cube around the borehole,its response curve exhibited a single-peak,and the extreme point of the curve corresponded to the center of the low-resistivity body.When the low-resistivity cube was directly below the borehole,the response curve showed three extreme values(two high and one low),with the low corresponding to the center of the low-resistivity body.The total field response of the low-resistivity overburden was stronger than that of the uniform half-space model due to the low-resistivity shielding effect of electromagnetic waves.When the receiving-transmitting distance gradually increased,the effect of the low-resistivity overburden was gradually weakened,and the response of the low-resistivity cube was strengthened.It was affected by the ratio of the overburden resistivity to the resistivity of the low-resistivity body.
文摘Electricity and magnetism and electromagnetic induction are phenomena that can be perceived by people. But their interpretation and theoretical study took a long time. The theoretical research on electricity began with the discovery of Coulomb’s law in 1785, while the theoretical research on magnetism began with the discovery of Oersted’s Law in 1820. From the 1850s to the 1870s, Maxwell summarized a set of theoretical equations for electromagnetism based on some laws of predecessors. However, this set of equations contains a few statistical relationships and empirical concepts, so it is difficult to explain the physical nature of electromagnetic phenomena and principles. This paper explained that the macro phenomenon of electricity is the separation of unlike charges of new electrons produced by the orthogonal collision of old particles under the action of external forces. The physical nature of magnetism is the potential energy (magnetic energy) and information associated with the overall orientation of the moving electrons solidly recorded in the material. The physical principle of electromagnetic induction describes how change in electric current intensity generates change in magnetic intensity and vice versa through orthogonal interaction of ordered electrons. This theoretical interpretation does not require the concepts of traditional electromagnetic forces, electromagnetic fields, magnetic moments, and magnetic domains.
文摘Recent decades have seen rapid advances in the field of electrical engineering, such that our environment has become a sea of electrical and magnetic signals, raising questions about the possible effects of low-frequency electromagnetic fields on the environment and which are capable of modifying and destroying our ecosystem. Particular interest was given in this article due to a massive influx of population living near high voltage lines. The analysis and simulation of the influence of low frequency electromagnetic fields on living beings in the vicinity of high voltage sources 132 kV and 220 kV in urban areas in DR Congo is the subject of our research with a view to estimating the level of exposure of humans to low frequency electromagnetic fields. To carry out our research, we used the classic method of analyzing the field produced near a high voltage line based on Maxwell’s image theory, the Maxwell-Gauss theorem and Maxwell-Ampère theorem to model and quantify low-frequency electromagnetic fields in the vicinity of high-voltage lines. The 2D FDTD numerical formulation was developed from telegraphers’ equations and allowed us to obtain models of current and voltage induced by electromagnetic fields on living beings below and near HV lines. The different simulations carried out on the proposed models illustrate the effects of the electrical and geometric parameters of the pylons on the distribution of the electromagnetic field in the vicinity of the HV lines. The results obtained were compared to the safety limits recommended by the standards.
文摘The signs of the electric field markers in Figs.2 and 4 of the paper[Chin.Phys.B 32104211(2023)]have been corrected.These modifications do not affect the results derived in the paper.
基金supported by the Institute of Seismology Foundation, China Earthquake Administration (201326126)
文摘The research about subsurface characteristics by using transient electromagnetic method(TEM) and high density resistivity method(HDRM) were already conducted in Ordos. The objective of this research is to detect coalmine goaf areas based on rock resistivity. The data processing using wavelet transform, three point smoothing, RES2 DINV and Maxwell processing software to obtain 2D resistivity structure. The results showed that the layers with maximum resistivity values(30e33 U m on Line 1, 30e31 U m on Line 2, 32e40 U m on Line3) are founded at station 1e7, and 14e20 on Line 1,13e18 on Line 2, and 8e13 and 16e20 on Line 3 which is predicted as goaf layer, and the minimum resistivity values(20e26 U m of TEM, 45e75 U m of HDRM) at the other layers. This resistivity difference was caused by the geology and characteristics of the study area which is located close by the cleugh with rich coal, so the goaf area distinguishable with aquifer layer and coal seam. The results were also significant accidents and serious destruction of ecological environment.
基金Supported by National Natural Science Foundation of China(Grant No.51607180)
文摘Current research in broken rotor bar(BRB) fault detection in induction motors is primarily focused on a high-frequency resolution analysis of the stator current.Compared with a discrete Fourier transformation, the parametric spectrum estimation technique has a higher frequency accuracy and resolution. However, the existing detection methods based on parametric spectrum estimation cannot realize online detection, owing to the large computational cost. To improve the efficiency of BRB fault detection,a new detection method based on the min-norm algorithm and least square estimation is proposed in this paper. First, the stator current is filtered using a band-pass filter and divided into short overlapped data windows. The min-norm algorithm is then applied to determine the frequencies of the fundamental and fault characteristic components with each overlapped data window. Next, based on the frequency values obtained, a model of the fault current signal is constructed. Subsequently, a linear least squares problem solved through singular value decomposition is designed to estimate the amplitudes and phases of the related components. Finally,the proposed method is applied to a simulated current and an actual motor,the results of which indicate that, not only parametric spectrum estimation technique.
文摘This paper proposes an effective method for early diagnosis (stress concentrating) of the oil-gas pipeline. Based on the principle of electromagnetic induction Faraday, we have designed and realized the nondestructive testing system for stress concentration area of ferromagnetic materials by means of the research of metal materials inverse magnetostrictive effect mechanism. The system changes the influence degree of the stress in ferromagnetic materials’ magnetic conductance to the corresponding voltage array by using discrete wavelet analysis method to process the data, in which not only the measuring accuracy is improved, but also the stress concentration is more directly reflected. The experiments confirm that the electromagnetic stress testing method is feasible and valid.
文摘The paper presents a mathematical multibody model of a soft mounted induction motor with sleeve bearings regarding forced vibrations caused by dynamic rotor eccentricities considering electromagnetic field damping. The multibody model contains the mass of the stator, rotor, shaft journals and bearing housings, the electromagnetic forces with respect of electromagnetic field damping, stiffness and internal (rotating) damping of the rotor, different kinds of dynamic rotor eccentricity, stiffness and damping of the bearing housings and end shields, stiffness and damping of the oil film of the sleeve bearings and stiffness and damping of the foundation. With this multibody model, the bearing housing vibrations and the relative shaft vibrations in the sleeve bearings can be derived.
文摘We discuss a thermoelectric energy generation (TEG) technique by employing a thermomechanical model of a drinking bird (DB). The motion of a drinking bird is produced by the entropy-flow explained by the second law of thermodynamics, which is one of the fundamental laws of heat engines. We propose a disk-magnet electromagnetic induction (DM-EMI) employed to the motion of a drinking bird. The generalization of DM-EMI to heat engines for?mechanoelectric?energy conversions and properties of extracted electric powers are specifically discussed. The electric power of DM-EMI has a limited power generation characteristic to a mechanical rotation produced by heat engines, but it will be very useful for practical applications to wind turbines, coal-fired and nuclear power plant for?mechanoelectric?energy conversions. The DM-EMI will contribute to environmental problems to maintain clean and susceptible energy as one of?energy?harvesting technologies.
基金Supported by the National Natural Science Foundation of China under Grant No 61601105
文摘The finite volume time domain(FVTD) algorithm and Green function algorithm are extended to Schwarzschild spacetime for numerical simulation of electromagnetic scattering. The FVTD method in Schwarzschild spacetime is developed by filling the flat spacetime with an equivalent medium. The Green function in Schwarzschild spacetime is acquired by solving initial value problems. Both the FVTD code and the Green function code are validated by numerical results. Scattering in Schwarzschild spacetime is simulated with these methods.
基金project supported by Science and Technology Innovation Fund(Grant No.KDY2019001)Integrated Geophysical Simulation Lab of Chang’an University(Key Laboratory of Chinese Geophysical Society)
文摘In recent years,in order to meet the practical needs of deep edge mine detection with large depth and high precision,transient electromagnetic method(TEM)near emission source detection mode has become an international advanced method(Xue et al.,2020).
基金This work was supported in part by the National Natural Science Foundation of China under Grant51307050。
文摘Voltage sag is one of the most common power quality disturbances in industry,which causes huge inrush currents in stator windings of induction motors,and adversely impacts the motor secure operation.This paper firstly introduces a 2D Time-Stepping multi-slice finite element method(2D T-S multi-slice FEM)which is used for calculating the magnetic field distribution in induction motors under different sag events.Then the paper deduces the transient analytical expression of stator inrush current based on the classical theory of AC motors and presents a separation method for the positive,negative and zero sequence values based on instantaneous currents.With this method,the paper studies the influences of voltage sag amplitude,phase-angle jump and initial phase angle on the stator positive-and negative-sequence peak currents of 5.5 kW and 55 kW induction motors.This paper further proposes a motor protection method under voltage sag condition with the stator negative-sequence peak currents as the protection threshold,so that the protection false trip can be avoided effectively.Finally,the calculation and analysis results are validated by the comparison of calculated and measured stator peak value of the 5.5 kW induction motor.
文摘A kind of signal acquisition circuit and the related signal processing method of the capacitanceelectromagnetic flowmeter (EMF) were introduced. The circuit can eliminate the influence of distributed capacitanceon the input impedance of the operational amplifier, and greatly improve the input impedance of the detection circuitto overcome the disadvantage of high signal source impedance. The rotating capacitor filter is a signal processingmethod based on the phase-sensitive detection technology. It can extract the weak signal from the strong and widebandbackground noise, so it is very suitable for the processing of capacitive electromagnetic flow signals. Throughthe comparison of the signal amplitude obtained at different flow rates and the comparison of signal spectrumcomponents before and after the filter, the effectiveness of the bootstrap signal acquisition circuit and rotatingcapacitor filtering method is verified.
