Stabilization of tearing modes and neoclassical tearing modes is of great importance for tokamak operation.Electron cyclotron waves(ECWs)have been extensively used to stabilize the tearing modes with the virtue of hig...Stabilization of tearing modes and neoclassical tearing modes is of great importance for tokamak operation.Electron cyclotron waves(ECWs)have been extensively used to stabilize the tearing modes with the virtue of highly localized power deposition.Complete suppression of the m/n=2/1 tearing mode(TM)by electron cyclotron resonance heating(ECRH)has been achieved successfully on the J-TEXT tokamak.The effects of ECW deposition location and power amplitude on the 2/1 TM suppression have been investigated.It is found that the suppression is more effective when the ECW power is deposited closer to the rational surface.As the ECW power increases to approximately 230 k W,the 2/1 TM can be completely suppressed.The island rotation frequency is increased when the island width is reduced.The experimental results show that the local heating inside the magnetic island and the resulting temperature perturbation increase at the O-point of the island play dominant roles in TM suppression.As the ECW power increases,the 2/1 island is suppressed to smaller island width,and the flow shear also plays a stabilizing effect on small magnetic islands.With the stabilizing contribution of heating and flow shear,the 2/1 TM can be completely suppressed.展开更多
During the current flat-top phase of electron cyclotron resonance heating discharges in the HL-2A Tokamak, the behaviour of runaway electrons has been studied by means of hard x-ray detectors and neutron diagnostics. ...During the current flat-top phase of electron cyclotron resonance heating discharges in the HL-2A Tokamak, the behaviour of runaway electrons has been studied by means of hard x-ray detectors and neutron diagnostics. During electron cyclotron resonance heating, it can be found that both hard x-ray radiation intensity and neutron emission flux fall rapidly to a very low level, which suggests that runaway electrons have been suppressed by electron cyclotron resonance heating. From the set of discharges studied in the present experiments, it has also been observed that the efficiency of runaway suppression by electron cyclotron resonance heating was apparently affected by two factors： electroh cyclotron resonance heating power and duration. These results have been analysed by using a test particle model. The decrease of the toroidal electric field due to electron cyclotron resonance heating results in a rapid fall in the runaway electron energy that may lead to a suppression of runaway electrons. During electron cyclotron resonance heating with different powers and durations, the runaway electrons will experience different slowing down processes. These different decay processes are the major cause for influencing the efficiency of runaway suppression. This result is related to the safe operation of the Tokamak and may bring an effective control of runaway electrons.展开更多
Theoretical calculation and experimental results for a polarizer with sinusoidal grooves used in the electron cyclotron resonance heating （ECRH） system of the HL-2A tokamak are presented. The calculation is based on...Theoretical calculation and experimental results for a polarizer with sinusoidal grooves used in the electron cyclotron resonance heating （ECRH） system of the HL-2A tokamak are presented. The calculation is based on an integral method developed in the vector theory of diffraction gratings, and the polarization characteristics obtained with a low-power test are in good agreement with the numerical calculated results. With the polarizer assembled in a miter bend in the ECRH transmission line, pure ordinary mode （O-mode） and extraordinary mode （X-mode） polarized waves are also expected in the high-power experiment, depending on the polarizer rotation angle and the toroidal injection angle of the electron cyclotron （EC） wave beam. Second-harmonic X-mode experiments were successfully explored in HL-2A. Experimental result revealed that the electron temperature increased from 0.8 keV （Ohmic heating phase） to 1.5 keV （second X-mode heating phase）.展开更多
Anomalous ion heat transport is analyzed in the T-10 tokamak plasma heated with electron cyclotron resonance heating(ECRH) in second-harmonic extra-ordinary mode. Predictive modeling with empirical scaling for Ohmical...Anomalous ion heat transport is analyzed in the T-10 tokamak plasma heated with electron cyclotron resonance heating(ECRH) in second-harmonic extra-ordinary mode. Predictive modeling with empirical scaling for Ohmical heat conductivity shows that in ECRH plasmas the calculated ion temperature could be overestimated, so an increase of anomalous ion heat transport is required. To study this effect two scans are presented: over the EC resonance position and over the ECRH power. The EC resonance position varies from the high-field side to the low-field side by variation of the toroidal magnetic field. The scan over the heating power is presented with on-axis and mixed ECRH regimes. Discharges with high anomalous ion heat transport are obtained in all considered regimes. In these discharges the power balance ion heat conductivity exceeds the neoclassical level by up to 10 times. The high ion heat transport regimes are distinguished by three parameters: the ratio Te/Ti, the normalized electron density gradient R/■, and the ion–ion collisionality νii~*. The combination of high Te/Ti, high νii~*, and R/■=6-10 results in values of normalized anomalous ion heat fluxes up to 10 times higher than in the low transport scenario.展开更多
Electron cyclotron heating on HL-2A has been simulated by TORAY-GA with a second harmonic extraordinary wave and a fundamental ordinary wave. The results show that the wave absorption of the second harmonic extraordin...Electron cyclotron heating on HL-2A has been simulated by TORAY-GA with a second harmonic extraordinary wave and a fundamental ordinary wave. The results show that the wave absorption of the second harmonic extraordinary wave is better than that of the fundamental ordinary wave. In order to understand the interaction mechanism between electrons and the two different polarization modes, the energy exchange between electrons and the two modes are theoretically analyzed, and it is found that the coupling intensity described by the Bessel function and different polarizations of the two modes are the main reasons leading to the above phenomenon. The theoretical results of this study fit well with the simulated and numerical results.展开更多
The gyrotron is one of the most promising high-power millimeter-wave sources for electron cyclotron resonance heating（ECRH） in controlled thermal nuclear fusion experiments.In this paper,the design of a high-frequen...The gyrotron is one of the most promising high-power millimeter-wave sources for electron cyclotron resonance heating（ECRH） in controlled thermal nuclear fusion experiments.In this paper,the design of a high-frequency interaction cavity of a 1 MW/140 GHz gyrotron is described in detail.The cavity is designed by using eigen mode analysis and radio frequency（RF） behavior calculation.Rounded transitions at the input and output tapers are designed for reducing mode conversion.With the obtained cavity structure,non-linear self-consistent equations are adopted to calculate its output power and efficiency.A particle-in-cell（PIC） method is used to simulate the beam-wave interaction process for obtaining the resonant frequency and output power of the cavity.The PIC simulation results match considerably well with the results obtained by the non-linear self-consistent calculation.The cavity is currently under construction and will be integrated with other components for overall testing.展开更多
A new 140 GHz/2 MW/3 s electron cyclotron resonance heating （ECRH） system composed of two units is now being constructed on HL-2A. As a part of the system, two trans- mission lines marked No.7 ＆ 8 play the role of ...A new 140 GHz/2 MW/3 s electron cyclotron resonance heating （ECRH） system composed of two units is now being constructed on HL-2A. As a part of the system, two trans- mission lines marked No.7 ＆ 8 play the role of carrying microwave power from two gyrotrons to the tokamak port. Based on the oversized circular corrugated waveguide technology, an evacu~ ated transmission system with high power capability and high transmission efficiency is designed. Details are presented for the design of the corrugated waveguide, the layout of the proposed lines and the vacuum pumping system. Then mode conversion losses due to coupling, misalignment, bends and gaps are discussed to serve as a reference for analyzing the transmission efficiency and alignment. Finally, a dual-modes propagation case consisting of the HEll and LPn even modes is discussed.展开更多
As a flexible auxiliary heating method,the electron cyclotron resonance heating（ECRH） has been widely used in many tokamaks and also will be applied for the J-TEXT tokamak.To meet requirements of protection and faul...As a flexible auxiliary heating method,the electron cyclotron resonance heating（ECRH） has been widely used in many tokamaks and also will be applied for the J-TEXT tokamak.To meet requirements of protection and fault analysis for the ECRH system on J-TEXT,signals of gyrotrons such as the cathode voltage and current,the anode voltage and current,etc should be transmitted to the control and data acquisition system.Considering the high voltage environment of gyrotrons,isolation transmission module based on FPGA and optical fiber communication has been designed and tested.The test results indicate that the designed module has strong anti-noise ability,low error rate and high transmission speed.The delay of the module is no more than 5 μs which can fulfill the requirements.展开更多
基金supported by the National Magnetic Confinement Fusion Energy R&D Program of China(No.2019YFE03010004)the Hubei Provincial Natural Science Foundation of China(No.2022CFA072)National Natural Science Foundation of China(No.51821005)。
文摘Stabilization of tearing modes and neoclassical tearing modes is of great importance for tokamak operation.Electron cyclotron waves(ECWs)have been extensively used to stabilize the tearing modes with the virtue of highly localized power deposition.Complete suppression of the m/n=2/1 tearing mode(TM)by electron cyclotron resonance heating(ECRH)has been achieved successfully on the J-TEXT tokamak.The effects of ECW deposition location and power amplitude on the 2/1 TM suppression have been investigated.It is found that the suppression is more effective when the ECW power is deposited closer to the rational surface.As the ECW power increases to approximately 230 k W,the 2/1 TM can be completely suppressed.The island rotation frequency is increased when the island width is reduced.The experimental results show that the local heating inside the magnetic island and the resulting temperature perturbation increase at the O-point of the island play dominant roles in TM suppression.As the ECW power increases,the 2/1 island is suppressed to smaller island width,and the flow shear also plays a stabilizing effect on small magnetic islands.With the stabilizing contribution of heating and flow shear,the 2/1 TM can be completely suppressed.
基金Project supported by the National Natural Science Foundation of China (Grant Nos 10675124,10775041 and 10775045)
文摘During the current flat-top phase of electron cyclotron resonance heating discharges in the HL-2A Tokamak, the behaviour of runaway electrons has been studied by means of hard x-ray detectors and neutron diagnostics. During electron cyclotron resonance heating, it can be found that both hard x-ray radiation intensity and neutron emission flux fall rapidly to a very low level, which suggests that runaway electrons have been suppressed by electron cyclotron resonance heating. From the set of discharges studied in the present experiments, it has also been observed that the efficiency of runaway suppression by electron cyclotron resonance heating was apparently affected by two factors： electroh cyclotron resonance heating power and duration. These results have been analysed by using a test particle model. The decrease of the toroidal electric field due to electron cyclotron resonance heating results in a rapid fall in the runaway electron energy that may lead to a suppression of runaway electrons. During electron cyclotron resonance heating with different powers and durations, the runaway electrons will experience different slowing down processes. These different decay processes are the major cause for influencing the efficiency of runaway suppression. This result is related to the safe operation of the Tokamak and may bring an effective control of runaway electrons.
文摘Theoretical calculation and experimental results for a polarizer with sinusoidal grooves used in the electron cyclotron resonance heating （ECRH） system of the HL-2A tokamak are presented. The calculation is based on an integral method developed in the vector theory of diffraction gratings, and the polarization characteristics obtained with a low-power test are in good agreement with the numerical calculated results. With the polarizer assembled in a miter bend in the ECRH transmission line, pure ordinary mode （O-mode） and extraordinary mode （X-mode） polarized waves are also expected in the high-power experiment, depending on the polarizer rotation angle and the toroidal injection angle of the electron cyclotron （EC） wave beam. Second-harmonic X-mode experiments were successfully explored in HL-2A. Experimental result revealed that the electron temperature increased from 0.8 keV （Ohmic heating phase） to 1.5 keV （second X-mode heating phase）.
文摘Anomalous ion heat transport is analyzed in the T-10 tokamak plasma heated with electron cyclotron resonance heating(ECRH) in second-harmonic extra-ordinary mode. Predictive modeling with empirical scaling for Ohmical heat conductivity shows that in ECRH plasmas the calculated ion temperature could be overestimated, so an increase of anomalous ion heat transport is required. To study this effect two scans are presented: over the EC resonance position and over the ECRH power. The EC resonance position varies from the high-field side to the low-field side by variation of the toroidal magnetic field. The scan over the heating power is presented with on-axis and mixed ECRH regimes. Discharges with high anomalous ion heat transport are obtained in all considered regimes. In these discharges the power balance ion heat conductivity exceeds the neoclassical level by up to 10 times. The high ion heat transport regimes are distinguished by three parameters: the ratio Te/Ti, the normalized electron density gradient R/■, and the ion–ion collisionality νii~*. The combination of high Te/Ti, high νii~*, and R/■=6-10 results in values of normalized anomalous ion heat fluxes up to 10 times higher than in the low transport scenario.
基金supported by the National Basic Research Program of China (973 Program) (No. 2010GB107003)
文摘Electron cyclotron heating on HL-2A has been simulated by TORAY-GA with a second harmonic extraordinary wave and a fundamental ordinary wave. The results show that the wave absorption of the second harmonic extraordinary wave is better than that of the fundamental ordinary wave. In order to understand the interaction mechanism between electrons and the two different polarization modes, the energy exchange between electrons and the two modes are theoretically analyzed, and it is found that the coupling intensity described by the Bessel function and different polarizations of the two modes are the main reasons leading to the above phenomenon. The theoretical results of this study fit well with the simulated and numerical results.
基金supported by International S&T Cooperation Program of China(No.2011DFA63190)China Postdoctoral Science Foundation(No.2014M552334)
文摘The gyrotron is one of the most promising high-power millimeter-wave sources for electron cyclotron resonance heating（ECRH） in controlled thermal nuclear fusion experiments.In this paper,the design of a high-frequency interaction cavity of a 1 MW/140 GHz gyrotron is described in detail.The cavity is designed by using eigen mode analysis and radio frequency（RF） behavior calculation.Rounded transitions at the input and output tapers are designed for reducing mode conversion.With the obtained cavity structure,non-linear self-consistent equations are adopted to calculate its output power and efficiency.A particle-in-cell（PIC） method is used to simulate the beam-wave interaction process for obtaining the resonant frequency and output power of the cavity.The PIC simulation results match considerably well with the results obtained by the non-linear self-consistent calculation.The cavity is currently under construction and will be integrated with other components for overall testing.
基金supported by the International Thermonuclear Experimental Reactor Special Fund of China(No.2009GB102002)partly supported by the Core University Program on Plasma and Nuclear Fusion between China and Japan
文摘A new 140 GHz/2 MW/3 s electron cyclotron resonance heating （ECRH） system composed of two units is now being constructed on HL-2A. As a part of the system, two trans- mission lines marked No.7 ＆ 8 play the role of carrying microwave power from two gyrotrons to the tokamak port. Based on the oversized circular corrugated waveguide technology, an evacu~ ated transmission system with high power capability and high transmission efficiency is designed. Details are presented for the design of the corrugated waveguide, the layout of the proposed lines and the vacuum pumping system. Then mode conversion losses due to coupling, misalignment, bends and gaps are discussed to serve as a reference for analyzing the transmission efficiency and alignment. Finally, a dual-modes propagation case consisting of the HEll and LPn even modes is discussed.
基金supported by the ITER Special Fund of China(Grant Nos.2013GB106001 and 2013GB106003)
文摘As a flexible auxiliary heating method,the electron cyclotron resonance heating（ECRH） has been widely used in many tokamaks and also will be applied for the J-TEXT tokamak.To meet requirements of protection and fault analysis for the ECRH system on J-TEXT,signals of gyrotrons such as the cathode voltage and current,the anode voltage and current,etc should be transmitted to the control and data acquisition system.Considering the high voltage environment of gyrotrons,isolation transmission module based on FPGA and optical fiber communication has been designed and tested.The test results indicate that the designed module has strong anti-noise ability,low error rate and high transmission speed.The delay of the module is no more than 5 μs which can fulfill the requirements.
