A thermal fatigue lifetime prediction model of ceramic ball grid array(CBGA)packages is proposed based on the Darveaux model.A finite element model of the CBGA packages is established,and the Anand model is used to de...A thermal fatigue lifetime prediction model of ceramic ball grid array(CBGA)packages is proposed based on the Darveaux model.A finite element model of the CBGA packages is established,and the Anand model is used to describe the viscoplasticity of the CBGA solder.The average viscoplastic strain energy density increment △Wave of the CBGA packages is obtained using a finite element simulation,and the influence of different structural parameters on theWave is analyzed.A simplified analytical model of the △Wave is established using the simulation data.The thermal fatigue lifetime of CBGA packages is obtained from a thermal cycling test.The Darveaux lifetime predictionmodel ismodified based on the thermal fatigue lifetime obtained fromthe experiment and the corresponding △Wave.A validation test is conducted to verify the accuracy of the thermal fatigue lifetime prediction model of the CBGA packages.This proposed model can be used in engineering to evaluate the lifetime of CBGA packages.展开更多
Carbon ions with a dose of 3×10<sup>17</sup> ions/cm<sup>2</sup> was implanted into Ti-6Al-4V alloy at anenergy of 80 keV.A 28% increase in edurance limit was found with implantation under...Carbon ions with a dose of 3×10<sup>17</sup> ions/cm<sup>2</sup> was implanted into Ti-6Al-4V alloy at anenergy of 80 keV.A 28% increase in edurance limit was found with implantation understress-controlled fatigue tests（R=O）.The surface microstructure changes induced by ionimplantation were identified using transmission electron microscopy（TEM）.The feature ofthe fracture surface were observed on scanning electron microscope（SEM）.The distributionprofile of the implanted ions was measured by secondary ion mass spectroscopy（SIMS）.Theimplanted surface layers contain a high density of irradiation defects and fine TiCprecipitates.Subsurface crack origins were found in specimens either with or withoutimplantation.The implanted species diffuse into matrix metal under the action of cyclic load-ing.A possible reason and mechanism for improving fatigue lifetime are also discussed.展开更多
In this study, fatigue tests under different R ratios were conducted on the AZ61 Mg alloy to investigate its fatigue lifetimes and fatigue crack growth (FCG) behavior. The fracture surface of the failed specimens was ...In this study, fatigue tests under different R ratios were conducted on the AZ61 Mg alloy to investigate its fatigue lifetimes and fatigue crack growth (FCG) behavior. The fracture surface of the failed specimens was investigated using a scanning electron microscope to study the size of the intermetallic compounds from which the pioneer fatigue crack initiated and led to the final failure of the specimen. To determine the maximum size of the intermetallic compounds existing within the cross section of the specimen at higher risk, Gumbel’s extreme-value statistics were utilized. In the present study, the intermetallic compounds contained within the specimen were assumed to be the initial cracks existing in the material before the fatigue tests. A modified linear elastic fracture-mechanics parameter, M, proposed by McEvily et al., was used to analyze the short FCG behavior under different stress ratios, R. The relation between the rate of FCG and M parameter was found to be useful and appropriate for predicting the fatigue lifetimes under different R ratios. Moreover, the probabilistic stress-fatigue life (P-S-N) curve of the material under different R ratios could be predicted with this method, which utilizes both the FCG law and a statistical distribution of sizes of the most dangerous intermetallic compounds. The evaluated results were in good agreement with the experimental ones. This correspondence indicates that the estimation method proposed in the present study is effective for evaluation of the probabilistic stress-fatigue life (P-S-N) curve of the material under different R ratios.展开更多
Samples prepared from as-extruded magnesium alloy Mg-3%Al-1%Zn (AZ31) billets were utilized in low-cycle fatigue tests in order to investigate the frequency-dependent fatigue life. Fully reversed strain-controlled ten...Samples prepared from as-extruded magnesium alloy Mg-3%Al-1%Zn (AZ31) billets were utilized in low-cycle fatigue tests in order to investigate the frequency-dependent fatigue life. Fully reversed strain-controlled tension-compression fatigue tests were carried out at frequencies of 1 Hz and 10 Hz in air. The microstructures were examined by optical microscopy (OM) and scanning electron microscopy (SEM).When the strain amplitude was lower than 0.2%, the fatigue life exhibited a positive correlation with loading frequency, and the activity of twinning was increased at 10 Hz. When the strain amplitude was higher than 0.2%, significant twinning was observed both at these two frequencies, and the fatigue life was found to be independent of frequency. The possible reasons for this frequency-related fatigue lifetime may be due to the dependence of twinning upon loading frequency and strain amplitude.展开更多
Strong anisotropic corrosion and mechanical properties caused by specimen orientations greatly limit the applications of wrought magnesium alloys.To investigate the influences of specimen orientation,the corrosion tes...Strong anisotropic corrosion and mechanical properties caused by specimen orientations greatly limit the applications of wrought magnesium alloys.To investigate the influences of specimen orientation,the corrosion tests and(corrosion)fatigue crack growth tests were conducted.The rolled and transverse surfaces of the materials show distinct corrosion rate differences in the stable corrosion stage,but the truth is the opposite for the initial stage of corrosion.In air,specimen orientations have a significant influence on the plastic deformation mechanisms near the crack tip,which results in different fatigue fracture surfaces and cracking paths.Compared with R-T specimens,N-T specimens show a slower fatigue crack growth(FCG)rate in air,which can be attributed to crack closure effects and deformation twinning near the crack tip.The corrosion environment will not significantly change the main plastic deformation mechanisms for the same type of specimen.However,the FCG rate in phosphate buffer saline(PBS)is one order of magnitude higher than that in air,which is caused by the combined effects of hydrogen-induced cracking and anodic dissolution.Owing to the similar corrosion rates at crack tips,the specimens with different orientations display close FCG rates in PBS.展开更多
Objective This study aimed to investigate the effect and underlying mechanism of Fructus lycii in improving exercise fatigue.Methods A network pharmacological approach was used to explore potential mechanisms of actio...Objective This study aimed to investigate the effect and underlying mechanism of Fructus lycii in improving exercise fatigue.Methods A network pharmacological approach was used to explore potential mechanisms of action of Fructus lycii.Skeletal muscle C2C12 cells and immunofluorescence were employed to verify the effect and mechanism of the representative components in Fructus lycii predicted by network pharmacological analysis.Results Six potential active components,namely quercetin,β-sitosterol,stigmasterol,7-Omethylluteolin-6-C-beta-glucoside_qt,atropine,and glycitein,were identified to have potency in improving exercise fatigue via multiple pathways,such as the PI3K-Akt,neuroactive ligand-receptor interaction,IL-17,TNF,and MAPK signaling pathways.The immunofluorescence results indicated that quercetin,a significant active component in Fructus lycii,increased the mean staining area of 2-NBDG,TMRM,and MitoTracker,and decreased the area of CellRox compared to the control.Furthermore,the protein expression levels of p-38 MAPK,p-MAPK,p-JNK,p-PI3K,and p-AKT markedly increased after quercetin treatment.Conclusion Fructus lycii might alleviate exercise fatigue through multiple components and pathways.Among these,quercetin appears to improve exercise fatigue by enhancing energy metabolism and reducing oxidative stress.The PI3K-AKT and MAPK signaling pathways also appear to play a role in this process.展开更多
Purpose–This review aims to give a critical view of the wheel/rail high frequency vibration-induced vibration fatigue in railway bogie.Design/methodology/approach–Vibration fatigue of railway bogie arising from the ...Purpose–This review aims to give a critical view of the wheel/rail high frequency vibration-induced vibration fatigue in railway bogie.Design/methodology/approach–Vibration fatigue of railway bogie arising from the wheel/rail high frequency vibration has become the main concern of railway operators.Previous reviews usually focused on the formation mechanism of wheel/rail high frequency vibration.This paper thus gives a critical review of the vibration fatigue of railway bogie owing to the short-pitch irregularities-induced high frequency vibration,including a brief introduction of short-pitch irregularities,associated high frequency vibration in railway bogie,typical vibration fatigue failure cases of railway bogie and methodologies used for the assessment of vibration fatigue and research gaps.Findings–The results showed that the resulting excitation frequencies of short-pitch irregularity vary substantially due to different track types and formation mechanisms.The axle box-mounted components are much more vulnerable to vibration fatigue compared with other components.The wheel polygonal wear and rail corrugation-induced high frequency vibration is the main driving force of fatigue failure,and the fatigue crack usually initiates from the defect of the weld seam.Vibration spectrum for attachments of railway bogie defined in the standard underestimates the vibration level arising from the short-pitch irregularities.The current investigations on vibration fatigue mainly focus on the methods to improve the accuracy of fatigue damage assessment,and a systematical design method for vibration fatigue remains a huge gap to improve the survival probability when the rail vehicle is subjected to vibration fatigue.Originality/value–The research can facilitate the development of a new methodology to improve the fatigue life of railway vehicles when subjected to wheel/rail high frequency vibration.展开更多
In order to study the anti-fatigue performance of RCA modified asphalt (RMA),the performance of RMA and 90#matrix asphalt with different modifier content were measured by asphalt penetration,ductility,softening point,...In order to study the anti-fatigue performance of RCA modified asphalt (RMA),the performance of RMA and 90#matrix asphalt with different modifier content were measured by asphalt penetration,ductility,softening point,Brookfield viscosity,rheological index,infrared spectrum and dielectric constant test.This paper discusses the changes of asphalt basic indexes,fatigue properties and asphalt components based on dielectric properties under different modifier contents,and analyzes the grey correlation degree between components and asphalt pavement performance indexes.The results show that the optimum content of RCA modifier is 16.7%of the asphalt quality according to the penetration,ductility,softening point,Brockfield viscosity,viscosity temperature curve and fatigue life.In the phase angle-strain curve,there is disorder in the latter part of the curve.According to the strain (ε_(d)) corresponding to the disorder point,a new fatigue failure criterion is proposed and proved.Based on the new asphalt fatigue failure criterion,the fatigue prediction model of asphalt mixture is improved,and the fatigue life predicted by the improved fatigue model is compared with the fatigue life obtained by four-point bending fatigue test.The results show that the proposed new asphalt fatigue failure criterion is reasonable,and the fatigue life predicted by the improved asphalt mixture fatigue prediction model is accurate.The research method of classifying asphalt components based on dielectric properties is simple and effective,and the components have a high correlation with the road performance of base asphalt and modified asphalt.展开更多
Drinking good quality water is essential for better health. It is therefore essential to assess the radiological quality of all water consumed in the District of Abidjan in order to prevent related hazards. Thus, the ...Drinking good quality water is essential for better health. It is therefore essential to assess the radiological quality of all water consumed in the District of Abidjan in order to prevent related hazards. Thus, the objective of this study was to assess the risk of cancer due to the ingestion of alpha and beta emitting radionuclides in the different types of water consumed in the region. A total of 63 water samples with 43 tap water samples, 5 bottled mineral water and 15 sachet water samples was collected and taken to GAEC laboratory for analysis. The low background Gas-less Automatic Alpha/Beta counting system (Canberra iMatic<sup>TM</sup>) was used to determine alpha and beta activity concentrations. Activity concentrations of both gross alpha and gross beta obtained in water sample were respectively lower than the WHO recommended limits of 0.1 Bq/l and 1 Bq/l. Also, the annual effective dose and total equivalent effective dose found in mineral bottled water samples were higher than in other types of water. The assessment of radiological lifetime risk has shown values of cancer risk due to ingestion alpha and beta emitters lower than recommended limit. These results indicate that there is no health hazard associated to consumption of water in the District of Abidjan.展开更多
In order to clarify the fatigue damage evolution of concrete exposed to flexural fatigue loads,ultrasonic pulse velocity(UPV),impact-echo technology and surface electrical resistance(SR) method were used.Damage variab...In order to clarify the fatigue damage evolution of concrete exposed to flexural fatigue loads,ultrasonic pulse velocity(UPV),impact-echo technology and surface electrical resistance(SR) method were used.Damage variable based on the change of velocity of ultrasonic pulse(Du) and impact elastic wave(Di)were defined according to the classical damage theory.The influences of stress level,loading frequency and concrete strength on damage variable were measured.The experimental results show that Du and Di both present a three-stages trend for concrete exposed to fatigue loads.Since impact elastic wave is more sensitive to the microstructure damage in stage Ⅲ,the critical damage variable,i e,the damage variable before the final fracture of concrete of Di is slightly higher than that of Du.Meanwhile,the evolution of SR of concrete exposed to fatigue loads were analyzed and the relationship between SR and Du,SR and Di of concrete exposed to fatigue loads were established.It is found that the SR of concrete was decreased with the increasing fatigue cycles,indicating that surface electrical resistance method can also be applied to describe the damage of ballastless track concrete exposed to fatigue loads.展开更多
BACKGROUND Hepatocellular carcinoma(HCC)is a prevalent malignancy,and transcatheter arterial embolization(TAE)has emerged as a pivotal therapeutic modality.How-ever,TAE may induce symptom distress and fatigue,adversel...BACKGROUND Hepatocellular carcinoma(HCC)is a prevalent malignancy,and transcatheter arterial embolization(TAE)has emerged as a pivotal therapeutic modality.How-ever,TAE may induce symptom distress and fatigue,adversely affecting the quality of life of patients.AIM To investigate symptom distress,fatigue,and associated factors in HCC patients undergoing TAE.METHODS We used a cross-sectional design and purposive sampling to enroll HCC patients who underwent TAE at our institution from January to December 2022.Question-naires were utilized to collect data on symptom distress and fatigue scores from the first to the third day after TAE.RESULTS Our study revealed a significant reduction in fatigue and symptom distress among patients after TAE.Pain,fatigue,insomnia,fever and abdominal dis-tension were the most common symptoms troubling patients during the first 3 d post-TAE.Marital status,presence of family support,physical functional status,age,and symptom distress were identified as predictors of fatigue in patients.CONCLUSION Healthcare professionals should educate HCC patients on symptom distress and INTRODUCTION Hepatocellular carcinoma(HCC)ranks as the fifth most prevalent cancer and the third leading cause of cancer-related mortality globally.Surgical intervention remains the cornerstone of HCC treatment;however,due to the challenges associated with early diagnosis and the lack of specific diagnostic markers,a considerable proportion of patients are diagnosed at advanced stages,rendering them ineligible for surgical interventions.Transcatheter arterial embolization(TAE)is an interventional therapeutic approach involving the insertion of a fine catheter via the femoral artery to reach the vasculature near the tumor site.TAE aims to obstruct the arterial supply to the tumor by deploying embolic agents,thereby inducing necrosis in cancer cells.This procedure is suitable for patients with good liver function and overall health,particularly those with large HCCs that have not invaded the portal vein[1,2].Nonetheless,following TAE,hepatocytes incur variable degrees of damage,leading to the development of a constel-lation of symptoms reminiscent of acute hepatitis.These symptoms include fatigue and systemic discomfort,such as nausea,vomiting,fever,abdominal pain,as well as transient elevations in aspartate aminotransferase(AST)and alanine aminotransferase(ALT),collectively referred to as postembolization syndrome[3,4].These symptoms may arise due to ischemia of the liver and gallbladder,temporary liver enlargement,and peritoneal irritation.While many studies have explored fatigue and symptom distress in cancer patients both nationally and internationally,with some focusing on symptom distress following transcatheter arterial chemoembolization,there has been limited in-depth investigation into the fatigue and symptom distress resulting from TAE treatment[5-8].Fatigue and pain are both subjective experiences,typically arising from the gradual depletion of energy reserves during the course of illness[9].Fatigue is particularly prevalent among cancer patients,with rates soaring as high as 90%.Despite extensive research exploring cancer-related fatigue and its influencing factors,a unanimous consensus remains elusive.Hence,the primary objective of this study was to investigate the symptom distress and fatigue experienced by liver cancer patients following TAE treatment and to analyze potential contributing factors.展开更多
Recently,a description on a practicability of the Wöhler Curve Method for low-cycle fatigue of metals was given by the author.By the description and the low cycle fatigue test data of 16 MnR steel,it is important...Recently,a description on a practicability of the Wöhler Curve Method for low-cycle fatigue of metals was given by the author.By the description and the low cycle fatigue test data of 16 MnR steel,it is important to show that,for low cycle fatigue of metals,such a way that a stress-based intensity parameter calculated by the linear-elastic analysis is taken to be a stress intensity parameter,S,to establish a relationship between the stress intensity parameter,S,and the fatigue life,N,is practicable.In this paper,many metallic materials from the literature are given to show that the Wöhler Curve Method is well suitable for low-cycle fatigue analysis of metals.展开更多
Objective:To observe the clinical effects of Jianpi Fuzheng Decoction in patients with gastric cancer and cancer-related fatigue(CRF).Methods:Using the random number table method as a reference,68 cases of gastric CRF...Objective:To observe the clinical effects of Jianpi Fuzheng Decoction in patients with gastric cancer and cancer-related fatigue(CRF).Methods:Using the random number table method as a reference,68 cases of gastric CRF were randomly divided into two groups.One group served as the control group and received basic treatment,while the other was the observation group.The observation group,in addition to the control group’s treatment,received Jianpi Fuzheng Decoction.The clinical treatment effectiveness,fatigue scores,immune function indicators,and treatment safety were compared between the two groups.Results:The total clinical treatment effectiveness of the observation group and the improvement in immune function indicators after treatment were higher than those of the control group.The fatigue score after treatment was lower in the observation group than in the control group(P<0.05).No serious adverse reactions occurred during the treatment in either group.Conclusion:Jianpi Fuzheng Decoction can enhance the clinical treatment effectiveness for gastric cancer patients with CRF.It facilitates the acceleration of fatigue symptom improvement and immune function enhancement.The medication’s safety is guaranteed,making it worthy of promotion.展开更多
Fatigue failure phenomena of the concrete structures under long-term low amplitude loading have attractedmore attention.Some structures,such as wind power towers,offshore platforms,and high-speed railways,may resist m...Fatigue failure phenomena of the concrete structures under long-term low amplitude loading have attractedmore attention.Some structures,such as wind power towers,offshore platforms,and high-speed railways,may resist millions of cycles loading during their intended lives.Over the past century,analytical methods for concrete fatigue are emerging.It is concluded that models for the concrete fatigue calculation can fall into four categories:the empirical model relying on fatigue tests,fatigue crack growth model in fracture mechanics,fatigue damage evolution model based on damage mechanics and advanced machine learning model.In this paper,a detailed review of fatigue computing methodology for concrete is presented,and the characteristics of different types of fatigue models have been stated and discussed.展开更多
Mental fatigue is a complex state that results from prolonged cognitive activity. Symptoms of mental fatigue can include change in mood, motivation, and temporary deterioration of various cognitive functions involved ...Mental fatigue is a complex state that results from prolonged cognitive activity. Symptoms of mental fatigue can include change in mood, motivation, and temporary deterioration of various cognitive functions involved in goal-directed behavior. Extensive research has been done to develop methods for recognizing physiological and psychophysiological signs of mental fatigue. This has allowed the development of many AI-based models to classify different levels of fatigue, using data extracted from eye-tracking device, EEG, or ECG. In this paper, we present an experimental protocol which aims to both generate/measure mental fatigue and provide effective strategies for recuperation via VR sessions paired with EEG and eye tracking devices. This paper first provides a comprehensive state-of-the-art of mental fatigue predictive factors, measurement methods, and recuperation strategies. Then the paper presents an experimental protocol resulting from the state-of-the-art to 1) generate and measure mental fatigue and 2) evaluate the effectiveness of virtual therapy for fatigue recuperation, using a virtual reality (VR) simulated environment. In our work, we successfully generated mental fatigue through completion of cognitive tasks in a virtual simulated environment. Participants showed significant decline in pupil diameter and theta/alpha score during the various cognitive tasks. We trained an RBF SVM classifier from Electroencephalogram (EEG) data classifying mental fatigue with 95% accuracy on the test set. Finally, our results show that the time allocated for virtual therapy did not improve pupil diameter in post-relaxation period. Further research on the impact of relaxation therapy on relaxation therapy should allocate time closer to the standard recovery time of 60 min.展开更多
The service condition determines the Rolling Contact Fatigue(RCF) failure mechanism and lifetime under ascertain material structure integrity parameter of thermal spray coating. The available literature on the RCF tes...The service condition determines the Rolling Contact Fatigue(RCF) failure mechanism and lifetime under ascertain material structure integrity parameter of thermal spray coating. The available literature on the RCF testing of thermal spray coatings under various condition services is considerable; it is generally difficult to synthesize all of the result to obtain a comprehensive understanding of the parameters which has a great effect on a thermal spray coating's resistance of RCF. The effects of service conditions(lubrication states, contact stresses, revolve speed, and slip ratio) on the changing of thermal spray coatings' contact fatigue lifetime is introduced systematically. The effects of different service condition on RCF failure mechanism of thermal spray coating from the change of material structure integrity are also summarized. Moreover, In order to enhance the RCF performance, the parameter optimal design formula of service condition and material structure integrity is proposed based on the effect of service condition on thermal spray coatings' contact fatigue lifetime and RCF failure mechanism. The shortage of available literature and the forecast focus in future researches are discussed based on available research. The explicit result of RCF lifetime law and parameter optimal design formula in term of lubrication states, contact stresses, revolve speed, and slip ratio, is significant to improve the RCF performance on the engineering application.展开更多
To better improve the lightweight and fatigue durability performance of the tractor cab,a multi-objective lightweight design of the cab was carried out in this study.First,the finite element model of the cab with coun...To better improve the lightweight and fatigue durability performance of the tractor cab,a multi-objective lightweight design of the cab was carried out in this study.First,the finite element model of the cab with counterweight loading was established and then confirmed by the physical testing,and use the inertial reliefmethod to obtain stress distribution under unit load.The cab-frame rigid-flexible couplingmulti-body dynamicsmodelwas built by Adams/car software.Taking the cab airbag mount displacement and acceleration signals acquired on the proving ground as the desired signals and obtaining the fatigue analysis load spectrum through Femfat-Lab virtual iteration.The fatigue simulation analysis is performed in nCode based on the Miner linear fatigue cumulative damage theory.Then,with themass and fatigue damage values as the optimization objectives,the bending-torsional stiffness and first-order bending-torsional mode as constraints,the thickness variables are screed based on the sensitivity analysis.The experimental design was carried out using the Optimal Latin hypercube method,and the multi-objective optimal design of the cab was carried out using theKriging approximationmodel fitting and particle swarmalgorithm.The weight of the optimized cab is reduced by 7.8%on the basis of meeting the fatigue durability performance.Finally,a seven-axis road simulation test rig was designed to verify its fatigue durability.The results show the optimized cab can consider both lightweight and durability.展开更多
Fatigue is a state commonly caused by overworked,which seriously affects daily work and life.How to detect mental fatigue has always been a hot spot for researchers to explore.Electroencephalogram(EEG)is considered on...Fatigue is a state commonly caused by overworked,which seriously affects daily work and life.How to detect mental fatigue has always been a hot spot for researchers to explore.Electroencephalogram(EEG)is considered one of the most accurate and objective indicators.This article investigated the devel-opment of classification algorithms applied in EEG-based fatigue detection in recent years.According to the different source of the data,we can divide these classification algorithms into two categories,intra-subject(within the same sub-ject)and cross-subject(across different subjects).In most studies,traditional machine learning algorithms with artificial feature extraction methods were com-monly used for fatigue detection as intra-subject algorithms.Besides,deep learn-ing algorithms have been applied to fatigue detection and could achieve effective result based on large-scale dataset.However,it is difficult to perform long-term calibration training on the subjects in practical applications.With the lack of large samples,transfer learning algorithms as a cross-subject algorithm could promote the practical application of fatigue detection methods.We found that the research based on deep learning and transfer learning has gradually increased in recent years.But as afield with increasing requirements,researchers still need to con-tinue to explore efficient decoding algorithms,design effective experimental para-digms,and collect and accumulate valid standard data,to achieve fast and accurate fatigue detection methods or systems to further widely apply.展开更多
The surface composite modification of the 7050 aluminum alloy friction stir-welded joints was performed by shot peening(SP)/multiple rotation rolling(MRR)and MRR/SP,and the fatigue performance of the nugget zone(NZ)wa...The surface composite modification of the 7050 aluminum alloy friction stir-welded joints was performed by shot peening(SP)/multiple rotation rolling(MRR)and MRR/SP,and the fatigue performance of the nugget zone(NZ)was investigated.The results demonstrated that the fatigue life of SP/MRR samples is longer than that of MRR/SP.On the plane 150μm below the surface.The grains with high angle grain boundary account for 71.5%and 34.3%for MRR/SP and SP/MRR samples,respectively.The crack propagation path of the MRR/SP is transgranular and intergranular,and it is intergranular for the MRR/SP.Multitudinous fatigue striations and some voids appeared at the fracture during the stable crack propagation stage.However,fatigue striations for SP/MRR are with smaller spacing,fewer holes,and smaller size under SP/MRR compared with fatigue fracture of MRR/SP.The differences in fatigue properties and fracture characteristics of the NZ are related to the microstructure after the two combined surface modifications.展开更多
文摘A thermal fatigue lifetime prediction model of ceramic ball grid array(CBGA)packages is proposed based on the Darveaux model.A finite element model of the CBGA packages is established,and the Anand model is used to describe the viscoplasticity of the CBGA solder.The average viscoplastic strain energy density increment △Wave of the CBGA packages is obtained using a finite element simulation,and the influence of different structural parameters on theWave is analyzed.A simplified analytical model of the △Wave is established using the simulation data.The thermal fatigue lifetime of CBGA packages is obtained from a thermal cycling test.The Darveaux lifetime predictionmodel ismodified based on the thermal fatigue lifetime obtained fromthe experiment and the corresponding △Wave.A validation test is conducted to verify the accuracy of the thermal fatigue lifetime prediction model of the CBGA packages.This proposed model can be used in engineering to evaluate the lifetime of CBGA packages.
文摘Carbon ions with a dose of 3×10<sup>17</sup> ions/cm<sup>2</sup> was implanted into Ti-6Al-4V alloy at anenergy of 80 keV.A 28% increase in edurance limit was found with implantation understress-controlled fatigue tests（R=O）.The surface microstructure changes induced by ionimplantation were identified using transmission electron microscopy（TEM）.The feature ofthe fracture surface were observed on scanning electron microscope（SEM）.The distributionprofile of the implanted ions was measured by secondary ion mass spectroscopy（SIMS）.Theimplanted surface layers contain a high density of irradiation defects and fine TiCprecipitates.Subsurface crack origins were found in specimens either with or withoutimplantation.The implanted species diffuse into matrix metal under the action of cyclic load-ing.A possible reason and mechanism for improving fatigue lifetime are also discussed.
文摘In this study, fatigue tests under different R ratios were conducted on the AZ61 Mg alloy to investigate its fatigue lifetimes and fatigue crack growth (FCG) behavior. The fracture surface of the failed specimens was investigated using a scanning electron microscope to study the size of the intermetallic compounds from which the pioneer fatigue crack initiated and led to the final failure of the specimen. To determine the maximum size of the intermetallic compounds existing within the cross section of the specimen at higher risk, Gumbel’s extreme-value statistics were utilized. In the present study, the intermetallic compounds contained within the specimen were assumed to be the initial cracks existing in the material before the fatigue tests. A modified linear elastic fracture-mechanics parameter, M, proposed by McEvily et al., was used to analyze the short FCG behavior under different stress ratios, R. The relation between the rate of FCG and M parameter was found to be useful and appropriate for predicting the fatigue lifetimes under different R ratios. Moreover, the probabilistic stress-fatigue life (P-S-N) curve of the material under different R ratios could be predicted with this method, which utilizes both the FCG law and a statistical distribution of sizes of the most dangerous intermetallic compounds. The evaluated results were in good agreement with the experimental ones. This correspondence indicates that the estimation method proposed in the present study is effective for evaluation of the probabilistic stress-fatigue life (P-S-N) curve of the material under different R ratios.
基金the National Natural Science Foundation of China(No.50901042)NUST Research Funding(No.2011YBXM156)
文摘Samples prepared from as-extruded magnesium alloy Mg-3%Al-1%Zn (AZ31) billets were utilized in low-cycle fatigue tests in order to investigate the frequency-dependent fatigue life. Fully reversed strain-controlled tension-compression fatigue tests were carried out at frequencies of 1 Hz and 10 Hz in air. The microstructures were examined by optical microscopy (OM) and scanning electron microscopy (SEM).When the strain amplitude was lower than 0.2%, the fatigue life exhibited a positive correlation with loading frequency, and the activity of twinning was increased at 10 Hz. When the strain amplitude was higher than 0.2%, significant twinning was observed both at these two frequencies, and the fatigue life was found to be independent of frequency. The possible reasons for this frequency-related fatigue lifetime may be due to the dependence of twinning upon loading frequency and strain amplitude.
基金the National Natural Science Foundation of China(Nos.52175143 and 51571150)。
文摘Strong anisotropic corrosion and mechanical properties caused by specimen orientations greatly limit the applications of wrought magnesium alloys.To investigate the influences of specimen orientation,the corrosion tests and(corrosion)fatigue crack growth tests were conducted.The rolled and transverse surfaces of the materials show distinct corrosion rate differences in the stable corrosion stage,but the truth is the opposite for the initial stage of corrosion.In air,specimen orientations have a significant influence on the plastic deformation mechanisms near the crack tip,which results in different fatigue fracture surfaces and cracking paths.Compared with R-T specimens,N-T specimens show a slower fatigue crack growth(FCG)rate in air,which can be attributed to crack closure effects and deformation twinning near the crack tip.The corrosion environment will not significantly change the main plastic deformation mechanisms for the same type of specimen.However,the FCG rate in phosphate buffer saline(PBS)is one order of magnitude higher than that in air,which is caused by the combined effects of hydrogen-induced cracking and anodic dissolution.Owing to the similar corrosion rates at crack tips,the specimens with different orientations display close FCG rates in PBS.
基金funded by China’s National Key R&D Programmers for“Hi-Tech Winter Olympics”Special Project[2020YFF0305001]。
文摘Objective This study aimed to investigate the effect and underlying mechanism of Fructus lycii in improving exercise fatigue.Methods A network pharmacological approach was used to explore potential mechanisms of action of Fructus lycii.Skeletal muscle C2C12 cells and immunofluorescence were employed to verify the effect and mechanism of the representative components in Fructus lycii predicted by network pharmacological analysis.Results Six potential active components,namely quercetin,β-sitosterol,stigmasterol,7-Omethylluteolin-6-C-beta-glucoside_qt,atropine,and glycitein,were identified to have potency in improving exercise fatigue via multiple pathways,such as the PI3K-Akt,neuroactive ligand-receptor interaction,IL-17,TNF,and MAPK signaling pathways.The immunofluorescence results indicated that quercetin,a significant active component in Fructus lycii,increased the mean staining area of 2-NBDG,TMRM,and MitoTracker,and decreased the area of CellRox compared to the control.Furthermore,the protein expression levels of p-38 MAPK,p-MAPK,p-JNK,p-PI3K,and p-AKT markedly increased after quercetin treatment.Conclusion Fructus lycii might alleviate exercise fatigue through multiple components and pathways.Among these,quercetin appears to improve exercise fatigue by enhancing energy metabolism and reducing oxidative stress.The PI3K-AKT and MAPK signaling pathways also appear to play a role in this process.
基金The author sincerely appreciates the help provided by the research team(Wheel/rail interaction,Vibration and Noise Research Team)and CRRC.In addition,this study has also been supported by Science and Technology Research Plan of China Railway General Corporation(No.P2019J002,N2022J009)China Association of Science and Technology Young Talent Support Project(No.2019QNRC001)+1 种基金National Natural Science Foundation(No.U1934203)Sichuan Science and Technology Program(No.2022NSFSC0469,2023NSFSC0374,2023YFH0049).
文摘Purpose–This review aims to give a critical view of the wheel/rail high frequency vibration-induced vibration fatigue in railway bogie.Design/methodology/approach–Vibration fatigue of railway bogie arising from the wheel/rail high frequency vibration has become the main concern of railway operators.Previous reviews usually focused on the formation mechanism of wheel/rail high frequency vibration.This paper thus gives a critical review of the vibration fatigue of railway bogie owing to the short-pitch irregularities-induced high frequency vibration,including a brief introduction of short-pitch irregularities,associated high frequency vibration in railway bogie,typical vibration fatigue failure cases of railway bogie and methodologies used for the assessment of vibration fatigue and research gaps.Findings–The results showed that the resulting excitation frequencies of short-pitch irregularity vary substantially due to different track types and formation mechanisms.The axle box-mounted components are much more vulnerable to vibration fatigue compared with other components.The wheel polygonal wear and rail corrugation-induced high frequency vibration is the main driving force of fatigue failure,and the fatigue crack usually initiates from the defect of the weld seam.Vibration spectrum for attachments of railway bogie defined in the standard underestimates the vibration level arising from the short-pitch irregularities.The current investigations on vibration fatigue mainly focus on the methods to improve the accuracy of fatigue damage assessment,and a systematical design method for vibration fatigue remains a huge gap to improve the survival probability when the rail vehicle is subjected to vibration fatigue.Originality/value–The research can facilitate the development of a new methodology to improve the fatigue life of railway vehicles when subjected to wheel/rail high frequency vibration.
基金Funded by Natural Science Foundation of Inner Mongolia,China (No. 2019MS05033)。
文摘In order to study the anti-fatigue performance of RCA modified asphalt (RMA),the performance of RMA and 90#matrix asphalt with different modifier content were measured by asphalt penetration,ductility,softening point,Brookfield viscosity,rheological index,infrared spectrum and dielectric constant test.This paper discusses the changes of asphalt basic indexes,fatigue properties and asphalt components based on dielectric properties under different modifier contents,and analyzes the grey correlation degree between components and asphalt pavement performance indexes.The results show that the optimum content of RCA modifier is 16.7%of the asphalt quality according to the penetration,ductility,softening point,Brockfield viscosity,viscosity temperature curve and fatigue life.In the phase angle-strain curve,there is disorder in the latter part of the curve.According to the strain (ε_(d)) corresponding to the disorder point,a new fatigue failure criterion is proposed and proved.Based on the new asphalt fatigue failure criterion,the fatigue prediction model of asphalt mixture is improved,and the fatigue life predicted by the improved fatigue model is compared with the fatigue life obtained by four-point bending fatigue test.The results show that the proposed new asphalt fatigue failure criterion is reasonable,and the fatigue life predicted by the improved asphalt mixture fatigue prediction model is accurate.The research method of classifying asphalt components based on dielectric properties is simple and effective,and the components have a high correlation with the road performance of base asphalt and modified asphalt.
文摘Drinking good quality water is essential for better health. It is therefore essential to assess the radiological quality of all water consumed in the District of Abidjan in order to prevent related hazards. Thus, the objective of this study was to assess the risk of cancer due to the ingestion of alpha and beta emitting radionuclides in the different types of water consumed in the region. A total of 63 water samples with 43 tap water samples, 5 bottled mineral water and 15 sachet water samples was collected and taken to GAEC laboratory for analysis. The low background Gas-less Automatic Alpha/Beta counting system (Canberra iMatic<sup>TM</sup>) was used to determine alpha and beta activity concentrations. Activity concentrations of both gross alpha and gross beta obtained in water sample were respectively lower than the WHO recommended limits of 0.1 Bq/l and 1 Bq/l. Also, the annual effective dose and total equivalent effective dose found in mineral bottled water samples were higher than in other types of water. The assessment of radiological lifetime risk has shown values of cancer risk due to ingestion alpha and beta emitters lower than recommended limit. These results indicate that there is no health hazard associated to consumption of water in the District of Abidjan.
基金Funded by the National Natural Science Foundation of China(Nos.U1934206,52208299,and 52108260)the 2021 Tencent XPLORER PRIZE。
文摘In order to clarify the fatigue damage evolution of concrete exposed to flexural fatigue loads,ultrasonic pulse velocity(UPV),impact-echo technology and surface electrical resistance(SR) method were used.Damage variable based on the change of velocity of ultrasonic pulse(Du) and impact elastic wave(Di)were defined according to the classical damage theory.The influences of stress level,loading frequency and concrete strength on damage variable were measured.The experimental results show that Du and Di both present a three-stages trend for concrete exposed to fatigue loads.Since impact elastic wave is more sensitive to the microstructure damage in stage Ⅲ,the critical damage variable,i e,the damage variable before the final fracture of concrete of Di is slightly higher than that of Du.Meanwhile,the evolution of SR of concrete exposed to fatigue loads were analyzed and the relationship between SR and Du,SR and Di of concrete exposed to fatigue loads were established.It is found that the SR of concrete was decreased with the increasing fatigue cycles,indicating that surface electrical resistance method can also be applied to describe the damage of ballastless track concrete exposed to fatigue loads.
基金The study was reviewed and approved by the Shanghai Fourth People’s Hospital Institutional Review Board(approval No.2022108-001).
文摘BACKGROUND Hepatocellular carcinoma(HCC)is a prevalent malignancy,and transcatheter arterial embolization(TAE)has emerged as a pivotal therapeutic modality.How-ever,TAE may induce symptom distress and fatigue,adversely affecting the quality of life of patients.AIM To investigate symptom distress,fatigue,and associated factors in HCC patients undergoing TAE.METHODS We used a cross-sectional design and purposive sampling to enroll HCC patients who underwent TAE at our institution from January to December 2022.Question-naires were utilized to collect data on symptom distress and fatigue scores from the first to the third day after TAE.RESULTS Our study revealed a significant reduction in fatigue and symptom distress among patients after TAE.Pain,fatigue,insomnia,fever and abdominal dis-tension were the most common symptoms troubling patients during the first 3 d post-TAE.Marital status,presence of family support,physical functional status,age,and symptom distress were identified as predictors of fatigue in patients.CONCLUSION Healthcare professionals should educate HCC patients on symptom distress and INTRODUCTION Hepatocellular carcinoma(HCC)ranks as the fifth most prevalent cancer and the third leading cause of cancer-related mortality globally.Surgical intervention remains the cornerstone of HCC treatment;however,due to the challenges associated with early diagnosis and the lack of specific diagnostic markers,a considerable proportion of patients are diagnosed at advanced stages,rendering them ineligible for surgical interventions.Transcatheter arterial embolization(TAE)is an interventional therapeutic approach involving the insertion of a fine catheter via the femoral artery to reach the vasculature near the tumor site.TAE aims to obstruct the arterial supply to the tumor by deploying embolic agents,thereby inducing necrosis in cancer cells.This procedure is suitable for patients with good liver function and overall health,particularly those with large HCCs that have not invaded the portal vein[1,2].Nonetheless,following TAE,hepatocytes incur variable degrees of damage,leading to the development of a constel-lation of symptoms reminiscent of acute hepatitis.These symptoms include fatigue and systemic discomfort,such as nausea,vomiting,fever,abdominal pain,as well as transient elevations in aspartate aminotransferase(AST)and alanine aminotransferase(ALT),collectively referred to as postembolization syndrome[3,4].These symptoms may arise due to ischemia of the liver and gallbladder,temporary liver enlargement,and peritoneal irritation.While many studies have explored fatigue and symptom distress in cancer patients both nationally and internationally,with some focusing on symptom distress following transcatheter arterial chemoembolization,there has been limited in-depth investigation into the fatigue and symptom distress resulting from TAE treatment[5-8].Fatigue and pain are both subjective experiences,typically arising from the gradual depletion of energy reserves during the course of illness[9].Fatigue is particularly prevalent among cancer patients,with rates soaring as high as 90%.Despite extensive research exploring cancer-related fatigue and its influencing factors,a unanimous consensus remains elusive.Hence,the primary objective of this study was to investigate the symptom distress and fatigue experienced by liver cancer patients following TAE treatment and to analyze potential contributing factors.
文摘Recently,a description on a practicability of the Wöhler Curve Method for low-cycle fatigue of metals was given by the author.By the description and the low cycle fatigue test data of 16 MnR steel,it is important to show that,for low cycle fatigue of metals,such a way that a stress-based intensity parameter calculated by the linear-elastic analysis is taken to be a stress intensity parameter,S,to establish a relationship between the stress intensity parameter,S,and the fatigue life,N,is practicable.In this paper,many metallic materials from the literature are given to show that the Wöhler Curve Method is well suitable for low-cycle fatigue analysis of metals.
基金2021 Open Project of the Key Research Office of the State Administration of Traditional Chinese Medicine“Treatment of Toxins and Evils in Gastric Cancer,”“Research on the Effect and Related Mechanisms of Jianpi Fuzheng Decoction in Improving Fatigue Related to Advanced Gastric Cancer,”(No.202138)2022 Xuzhou Key R&D Plan(Social Development)Project-Medical and Health Care,“Research on the Clinical Application of Jianpi Fuzheng Decoction in the Treatment of Cancer-Related Fatigue,”(No.:KC22276)。
文摘Objective:To observe the clinical effects of Jianpi Fuzheng Decoction in patients with gastric cancer and cancer-related fatigue(CRF).Methods:Using the random number table method as a reference,68 cases of gastric CRF were randomly divided into two groups.One group served as the control group and received basic treatment,while the other was the observation group.The observation group,in addition to the control group’s treatment,received Jianpi Fuzheng Decoction.The clinical treatment effectiveness,fatigue scores,immune function indicators,and treatment safety were compared between the two groups.Results:The total clinical treatment effectiveness of the observation group and the improvement in immune function indicators after treatment were higher than those of the control group.The fatigue score after treatment was lower in the observation group than in the control group(P<0.05).No serious adverse reactions occurred during the treatment in either group.Conclusion:Jianpi Fuzheng Decoction can enhance the clinical treatment effectiveness for gastric cancer patients with CRF.It facilitates the acceleration of fatigue symptom improvement and immune function enhancement.The medication’s safety is guaranteed,making it worthy of promotion.
基金supported by the National Natural Science Foundation of China(Grant Nos.52078361 and 51678439)Innovation Program of Shanghai Municipal Education Commission(Grant No.2017-01-07-00-07-E00006).
文摘Fatigue failure phenomena of the concrete structures under long-term low amplitude loading have attractedmore attention.Some structures,such as wind power towers,offshore platforms,and high-speed railways,may resist millions of cycles loading during their intended lives.Over the past century,analytical methods for concrete fatigue are emerging.It is concluded that models for the concrete fatigue calculation can fall into four categories:the empirical model relying on fatigue tests,fatigue crack growth model in fracture mechanics,fatigue damage evolution model based on damage mechanics and advanced machine learning model.In this paper,a detailed review of fatigue computing methodology for concrete is presented,and the characteristics of different types of fatigue models have been stated and discussed.
文摘Mental fatigue is a complex state that results from prolonged cognitive activity. Symptoms of mental fatigue can include change in mood, motivation, and temporary deterioration of various cognitive functions involved in goal-directed behavior. Extensive research has been done to develop methods for recognizing physiological and psychophysiological signs of mental fatigue. This has allowed the development of many AI-based models to classify different levels of fatigue, using data extracted from eye-tracking device, EEG, or ECG. In this paper, we present an experimental protocol which aims to both generate/measure mental fatigue and provide effective strategies for recuperation via VR sessions paired with EEG and eye tracking devices. This paper first provides a comprehensive state-of-the-art of mental fatigue predictive factors, measurement methods, and recuperation strategies. Then the paper presents an experimental protocol resulting from the state-of-the-art to 1) generate and measure mental fatigue and 2) evaluate the effectiveness of virtual therapy for fatigue recuperation, using a virtual reality (VR) simulated environment. In our work, we successfully generated mental fatigue through completion of cognitive tasks in a virtual simulated environment. Participants showed significant decline in pupil diameter and theta/alpha score during the various cognitive tasks. We trained an RBF SVM classifier from Electroencephalogram (EEG) data classifying mental fatigue with 95% accuracy on the test set. Finally, our results show that the time allocated for virtual therapy did not improve pupil diameter in post-relaxation period. Further research on the impact of relaxation therapy on relaxation therapy should allocate time closer to the standard recovery time of 60 min.
基金Supported by Distinguished Young Scholars of National Natural Science Foundation of China(Grant No.51125023)National Basic Research Program of China(973program,Grant No.2011CB013405)+1 种基金National Natural Science Foundation of China(Grant Nos.5127552651275105)Fundamental Research Funds for the Central Universities(Grant Nos.HEUCF20130910003,201403017)
文摘The service condition determines the Rolling Contact Fatigue(RCF) failure mechanism and lifetime under ascertain material structure integrity parameter of thermal spray coating. The available literature on the RCF testing of thermal spray coatings under various condition services is considerable; it is generally difficult to synthesize all of the result to obtain a comprehensive understanding of the parameters which has a great effect on a thermal spray coating's resistance of RCF. The effects of service conditions(lubrication states, contact stresses, revolve speed, and slip ratio) on the changing of thermal spray coatings' contact fatigue lifetime is introduced systematically. The effects of different service condition on RCF failure mechanism of thermal spray coating from the change of material structure integrity are also summarized. Moreover, In order to enhance the RCF performance, the parameter optimal design formula of service condition and material structure integrity is proposed based on the effect of service condition on thermal spray coatings' contact fatigue lifetime and RCF failure mechanism. The shortage of available literature and the forecast focus in future researches are discussed based on available research. The explicit result of RCF lifetime law and parameter optimal design formula in term of lubrication states, contact stresses, revolve speed, and slip ratio, is significant to improve the RCF performance on the engineering application.
基金supported in part by the Science and Technology Major Project of Guangxi under Grants AA18242033 and AA19182004in part by the Key Research andDevelopment Program of Guangxi AB21196029+3 种基金in part by the Scientific Research and Technology Development in Liuzhou 2020GAAA0404,2021AAA0104 and 2021AAA0112in part by the Guangxi Higher Education Undergraduate Teaching Reform Project Grant 2021JGA180in part by the GUET Education Undergraduate Teaching Reform Project Grant JGB202002in part by the Innovation Project of GUET Graduate Education (2022YCXS017).
文摘To better improve the lightweight and fatigue durability performance of the tractor cab,a multi-objective lightweight design of the cab was carried out in this study.First,the finite element model of the cab with counterweight loading was established and then confirmed by the physical testing,and use the inertial reliefmethod to obtain stress distribution under unit load.The cab-frame rigid-flexible couplingmulti-body dynamicsmodelwas built by Adams/car software.Taking the cab airbag mount displacement and acceleration signals acquired on the proving ground as the desired signals and obtaining the fatigue analysis load spectrum through Femfat-Lab virtual iteration.The fatigue simulation analysis is performed in nCode based on the Miner linear fatigue cumulative damage theory.Then,with themass and fatigue damage values as the optimization objectives,the bending-torsional stiffness and first-order bending-torsional mode as constraints,the thickness variables are screed based on the sensitivity analysis.The experimental design was carried out using the Optimal Latin hypercube method,and the multi-objective optimal design of the cab was carried out using theKriging approximationmodel fitting and particle swarmalgorithm.The weight of the optimized cab is reduced by 7.8%on the basis of meeting the fatigue durability performance.Finally,a seven-axis road simulation test rig was designed to verify its fatigue durability.The results show the optimized cab can consider both lightweight and durability.
基金funded by the National Natural Science Foundation of China(Grant Nos.61906019,62006082 and 62076103)the Guangdong Basic and Applied Basic Research Foundation(Grant Nos.2021A1515011853,2021A1515011600 and 2020A1515110294)+1 种基金Guangzhou Science and Technology Plan Project(Grant No.202102020877)the Guangzhou Science and Technology Plan Project Key Field R&D Project(202007030005).
文摘Fatigue is a state commonly caused by overworked,which seriously affects daily work and life.How to detect mental fatigue has always been a hot spot for researchers to explore.Electroencephalogram(EEG)is considered one of the most accurate and objective indicators.This article investigated the devel-opment of classification algorithms applied in EEG-based fatigue detection in recent years.According to the different source of the data,we can divide these classification algorithms into two categories,intra-subject(within the same sub-ject)and cross-subject(across different subjects).In most studies,traditional machine learning algorithms with artificial feature extraction methods were com-monly used for fatigue detection as intra-subject algorithms.Besides,deep learn-ing algorithms have been applied to fatigue detection and could achieve effective result based on large-scale dataset.However,it is difficult to perform long-term calibration training on the subjects in practical applications.With the lack of large samples,transfer learning algorithms as a cross-subject algorithm could promote the practical application of fatigue detection methods.We found that the research based on deep learning and transfer learning has gradually increased in recent years.But as afield with increasing requirements,researchers still need to con-tinue to explore efficient decoding algorithms,design effective experimental para-digms,and collect and accumulate valid standard data,to achieve fast and accurate fatigue detection methods or systems to further widely apply.
基金supported by the National Natural Science Foundation of China(Grants 51865028)the Gansu Provincial Science and Technology Planning Project(Grant No.20YF8GA056).
文摘The surface composite modification of the 7050 aluminum alloy friction stir-welded joints was performed by shot peening(SP)/multiple rotation rolling(MRR)and MRR/SP,and the fatigue performance of the nugget zone(NZ)was investigated.The results demonstrated that the fatigue life of SP/MRR samples is longer than that of MRR/SP.On the plane 150μm below the surface.The grains with high angle grain boundary account for 71.5%and 34.3%for MRR/SP and SP/MRR samples,respectively.The crack propagation path of the MRR/SP is transgranular and intergranular,and it is intergranular for the MRR/SP.Multitudinous fatigue striations and some voids appeared at the fracture during the stable crack propagation stage.However,fatigue striations for SP/MRR are with smaller spacing,fewer holes,and smaller size under SP/MRR compared with fatigue fracture of MRR/SP.The differences in fatigue properties and fracture characteristics of the NZ are related to the microstructure after the two combined surface modifications.
