The seepage characteristics of multiscale porous media is of considerable significance in many scientific and engineering fields.The Darcy permeability is one of the key macroscopic physical properties to characterize...The seepage characteristics of multiscale porous media is of considerable significance in many scientific and engineering fields.The Darcy permeability is one of the key macroscopic physical properties to characterize the seepage capacity of porous media.Therefore,based on the statistically fractal scaling law of porous media,fractal geometry is applied to model the multiscale pore structures.And a two-dimensional fractal orifice-throat model with multiscale and tortuous characteristics is proposed for the seepage flow through porous media.The analytical expression for Darcy permeability of porous media is derived,which is validated by comparing with available experimental data.The results show that the Darcy permeability is significantly influenced by porosity,orifice-throat fractal dimension,minimum to maximum diameter ratio,orifice-throat ratio and tortuosity fractal dimension.The present results are helpful for understanding the seepage mechanism of multiscale porous media,and may provide theoretical basis for unconventional oil and gas exploration and development,porous phase transition energy storage composites,CO2 geological sequestration,environmental protection and nuclear waste treatment,etc.展开更多
The Indo-Gangetic Plain(IGP)is one of the most seismically vulnerable areas due to its proximity to the Himalayas.Geographic information system(GIS)-based seismic characterization of the IGP was performed based on the...The Indo-Gangetic Plain(IGP)is one of the most seismically vulnerable areas due to its proximity to the Himalayas.Geographic information system(GIS)-based seismic characterization of the IGP was performed based on the degree of deformation and fractal dimension.The zone between the Main Boundary Thrust(MBT)and the Main Central Thrust(MCT)in the Himalayan Mountain Range(HMR)experienced large variations in earthquake magnitude,which were identified by Number-Size(NS)fractal modeling.The central IGP zone experienced only moderate to low mainshock levels.Fractal analysis of earthquake epicenters reveals a large scattering of earthquake epicenters in the HMR and central IGP zones.Similarly,the fault fractal analysis identifies the HMR,central IGP,and south-western IGP zones as having more faults.Overall,the seismicity of the study region is strong in the central IGP,south-western IGP,and HMR zones,moderate in the western and southern IGP,and low in the northern,eastern,and south-eastern IGP zones.展开更多
This research focused on the three-dimensional(3 D) seepage field simulation of a high concrete-faced rockfill dam(CFRD) under complex hydraulic conditions. A generalized equivalent continuum model of fractured rock m...This research focused on the three-dimensional(3 D) seepage field simulation of a high concrete-faced rockfill dam(CFRD) under complex hydraulic conditions. A generalized equivalent continuum model of fractured rock mass was used for equivalent continuous seepage field analysis based on the improved node virtual flow method. Using a high CFRD as an example, the generalized equivalent continuum range was determined, and a finite element model was established based on the terrain and geological conditions, as well as structural face characteristics of the dam area. The equivalent seepage coefficients of different material zones or positions in the dam foundation were calculated with the Snow model or inverse analysis. Then, the 3 D seepage field in the dam area was calculated under the normal water storage conditions, and the corresponding water head distribution, seepage flow, seepage gradient, and seepage characteristics in the dam area were analyzed. The results show that the generalized equivalent continuum model can effectively simulate overall seepage patterns of the CFRD under complex hydraulic conditions and provide a reference for seepage analysis of similar CFRDs.展开更多
Based on an analysis of the fractal structures and mass transport mechanism of typical shear-fluid-ore formation system, the fractal dispersion theory of the fluid system was used in the dynamic study of the ore forma...Based on an analysis of the fractal structures and mass transport mechanism of typical shear-fluid-ore formation system, the fractal dispersion theory of the fluid system was used in the dynamic study of the ore formation system. The model of point-source diffusive illuviation of the shear-fluid-ore formation system was constructed, and the numerical simulation of dynamics of the ore formation system was finished. The result shows that: (1) The metallogenic system have nested fractal structure. Different fractal dimension values in different systems show unbalance and inhomogeneity of ore-forming processes in the geohistory. It is an important parameter to symbolize the process of remobilization and accumulation of ore-forming materials. Also it can indicate the dynamics of the metallogenic system quantitatively to some extent. (2) In essence, the fractal dispersive ore-forming dynamics is a combination of multi-processes dominated by fluid dynamics and supplemented by molecule dispersion in fluids and fluid-rock interaction. It changes components and physico-chemical properties of primary rocks and fluids, favouring deposition and mineralization of ore-forming materials. (3) Gold ore-forming processes in different types of shear zones are quite different. (1) In a metallogenic system with inhomogeneous volumetric change and inhomogeneous shear, mineralization occurs in structural barriers in the centre of a shear zone and in geochemical barriers in the shear zone near its boundaries. But there is little possibility of mineralization out of the shear zone. (2) As to a metallogenic system with inhomogeneous volumetric change and simple shear, mineralization may occur only in structural barriers near the centre of the shear zone. (3) In a metallogenic system with homogeneous volumetric change and inhomogeneous shear, mineralization may occur in geochemical barriers both within and out of the shear zone.展开更多
Affected by external environmental factors and evolution of dam performance, dam seepage behavior shows nonlinear time-varying characteristics. In this study, to predict and evaluate the long-term development trend an...Affected by external environmental factors and evolution of dam performance, dam seepage behavior shows nonlinear time-varying characteristics. In this study, to predict and evaluate the long-term development trend and short-term fluctuation of the dam seepage behavior, two monitoring models were developed, one for the base flow effect and one for daily variation of dam seepage elements. In the first model, to avoid the influence of the time lag effect on the evaluation of seepage variation with the time effect component of seepage elements, the base values of the seepage element and the reservoir water level were extracted using the wavelet multi-resolution analysis method, and the time effect component was separated by the established base flow effect monitoring model. For the development of the daily variation monitoring model for dam seepage elements, all the previous factors, of which the measured time series prior to the dam seepage element monitoring time may have certain influence on the monitored results, were considered. Those factors that were positively correlated with the analyzed seepage element were initially considered to be the support vector machine(SVM) model input factors, and then the SVM kernel function-based sensitivity analysis was performed to optimize the input factor set and establish the optimized daily variation SVM model. The efficiency and rationality of the two models were verified by case studies of the water level of two piezometric tubes buried under the slope of a concrete gravity dam.Sensitivity analysis of the optimized SVM model shows that the influences of the daily variation of the upstream reservoir water level and rainfall on the daily variation of piezometric tube water level are processes subject to normal distribution.展开更多
Extreme hydrological events induced by typhoons in reservoir areas have presented severe challenges to the safe operation of hydraulic structures. Based on analysis of the seepage characteristics of an earth rock dam,...Extreme hydrological events induced by typhoons in reservoir areas have presented severe challenges to the safe operation of hydraulic structures. Based on analysis of the seepage characteristics of an earth rock dam, a novel seepage safety monitoring model was constructed in this study. The nonlinear influence processes of the antecedent reservoir water level and rainfall were assumed to follow normal distributions.The particle swarm optimization(PSO) algorithm was used to optimize the model parameters so as to raise the fitting accuracy. In addition, a mutation factor was introduced to simulate the sudden increase in the piezometric level induced by short-duration heavy rainfall and the possible historical extreme reservoir water level during a typhoon. In order to verify the efficacy of this model, the earth rock dam of the Siminghu Reservoir was used as an example. The piezometric level at the SW1-2 measuring point during Typhoon Fitow in 2013 was fitted with the present model, and a corresponding theoretical expression was established. Comparison of fitting results of the piezometric level obtained from the present statistical model and traditional statistical model with monitored values during the typhoon shows that the present model has a higher fitting accuracy and can simulate the uprush feature of the seepage pressure during the typhoon perfectly.展开更多
The contact sti ness of a mechanical bonding surface is an important parameter in determining the normal and radial contact force. To improve the calculation accuracy of the contact force model, the surface roughness ...The contact sti ness of a mechanical bonding surface is an important parameter in determining the normal and radial contact force. To improve the calculation accuracy of the contact force model, the surface roughness of the bonding surface and the energy loss that necessarily occurs during the impact process should be considered com?prehensively. To study the normal contact force of a revolute joint with clearance more accurately in the case of dry friction, a nonlinear sti ness coe cient model considering the surface roughness was established based on fractal theory, which considers the elastic, elastic?plastic, and plastic deformations of the asperities of the contact surface during the contact process. On this basis, a modified nonlinear spring damping model was established based on the Lankarani–Nikravesh contact force model. The laws influencing the surface roughness, recovery coe cient, initial velocity, and clearance size on the impact force were revealed, and were compared with the Lankarani–Nikravesh model and a hybrid model using MATLAB. The maximum impact force was obtained using a modified contact force model under di erent initial velocities, di erent clearances, and di erent degrees of surface roughness, and the calculated results were then compared with the experiment results. This study indicates that the modified model can be used more widely than other models, and is suitable for both large and small clearances. In particular, the modified model is more accurate when calculating the contact force of a revolute joint with a small clearance.展开更多
Establishing a long air gap discharge model considering the streamer-leader transition and randomness of the discharge path is of great signiflcance to improve the accuracy of discharge characteristic prediction and o...Establishing a long air gap discharge model considering the streamer-leader transition and randomness of the discharge path is of great signiflcance to improve the accuracy of discharge characteristic prediction and optimize external insulation design.Based on fractal theory and thermal ionization theory of streamer-leader transition,this work establishes a dynamic development model for the long air gap discharge streamer-leader system,which includes streamer inception,streamer development,leader inception,development of streamer-leader system and flnal jump.The positive discharge process of a 3 m rod plate is simulated to obtain the fractal distribution of the discharge path and the law of leader development for comparison with the discharge test results.The results show that the simulation model is similar to test results in the development characteristics of leader path distribution,each stage time and leader velocity.Finally,a simulation calculation of a 50%breakdown voltage of the rod-plate gap and ball-plate gap is carried out,with results fairly consistent with test data,proving the effectiveness and practicality of the model.展开更多
Because the result of the MB fractal model contradicts with the classical contact mechanics, a revised elastoplastic contact model of a single asperity is developed based on fractal theory. The critical areas of a sin...Because the result of the MB fractal model contradicts with the classical contact mechanics, a revised elastoplastic contact model of a single asperity is developed based on fractal theory. The critical areas of a single asperity are scale dependent, with an increase in the contact load and contact area, a transition from elastic, elastoplastic to full plastic deformation takes place in this order. In considering the size distribution function, analytic expression between the total contact load and the real contact area on the contact surface is obtained. The elastic, elastoplastic and full plastic contact load are obtained by the critical elastic contact area of the biggest asperity and maximun contact area of a single asperity. The results show that a rough surface is firstly in elastic deformation. As the load increases, elastoplastic or full plastic deformation takes place. For constant characteristic length scale G, the slope of load-area relation is proportional to fractal dimension D. For constant fractal dimension D, the slope of load-area relation is inversely proportional to G. For constant D and G, the slope of load-area relation is inversely proportional to property of the material ? , namely with the same load, the material of rough surface is softer, and the total contact area is larger. The contact mechanics model provides a foundation for study of the friction, wear and seal performance of rough surfaces.展开更多
The thermal contact conductance problem is an important issue in studying the heat transfer of engineering surfaces,which has been widely studied since last few decades,and for predicting which many theoretical models...The thermal contact conductance problem is an important issue in studying the heat transfer of engineering surfaces,which has been widely studied since last few decades,and for predicting which many theoretical models have been established.However,the models which have been existed are lack of objectivity due to that they are mostly studied based on the statistical methodology characterization for rough surfaces and simple partition for the deformation formats of contact asperity.In this paper,a fractal prediction model is developed for the thermal contact conductance between two rough surfaces based on the rough surface being described by three-dimensional Weierstrass and Mandelbrot fractal function and assuming that there are three kinds of asperity deformation modes:elastic,elastoplastic and fully plastic.Influences of contact load and contact area as well as fractal parameters and material properties on the thermal contact conductance are investigated by using the presented model.The investigation results show that the thermal contact conductance increases with the increasing of the contact load and contact area.The larger the fractal dimension,or the smaller the fractal roughness,the larger the thermal contact conductance is.The thermal contact conductance increases with decreasing the ratio of Young's elastic modulus to the microhardness.The results obtained indicate that the proposed model can effectively predict the thermal contact conductance at the interface,which provide certain reference to the further study on the issue of heat transfer between contact surfaces.展开更多
The target in this investigation is separation and delineation of geochemical anomalies for the single element Cu in Mesgaran mining area, eastern Iran. Mesgaran mining area is located in south part of Sarbishe county...The target in this investigation is separation and delineation of geochemical anomalies for the single element Cu in Mesgaran mining area, eastern Iran. Mesgaran mining area is located in south part of Sarbishe county with about 29 Km distance to the county center. This region is part of an Ophiolite sequence and the copper anomalies seem to be related to a volcanic massive sulfide (VMS) deposit whose main part (massive sulfide Lens) has been eroded. In order to delineate Cu anomalies, the boxplot as an Exploratory Data Analysis (EDA) method and concentration-volume (C-V) Fractal modeling are employed. Both of the methods reveal low-deep anomalies which are highly correlated with geological and geophysical studies. As the main result of this study we show that Fractal modeling in spite of the Boxplot, is not recommended for complex geological settings. The proved shallow anomalies recorded by geophysical studies and defined by the used methods are in accordance to the stringer zone of a volcanic massive sulfide (VMS) deposit in Mesgaran mining area which means this region is the bottom of a VMS deposit and geochemical anomalies are related to the remained parts of the deposit.展开更多
Soil water retention characteristics are the key information required in hydrological modeling. Frac-tal models provide a practical alternative for indirectly estimating soil water retention characteristics frompartic...Soil water retention characteristics are the key information required in hydrological modeling. Frac-tal models provide a practical alternative for indirectly estimating soil water retention characteristics fromparticle-size distribution data. Predictive capabilities of three fractal models, i.e, Tyler-Wheatcraft model,Rieu-Sposito model, and Brooks-Corey model, were fully evaluated in this work using experimental datafrom an international database and literature. Particle-size distribution data were firstly interpolated into20 classes using a van Genuchten-type equation. Fractal dimensions of the tortuous pore wall and the poresurface were then calculated from the detailed particle-size distribution and incorporated as a parameter infractal water retention models. Comparisons between measured and model-estimated water retention cha-racteristics indicated that these three models were applicable to relatively different soil textures and pressurehead ranges. Tyler-Wheatcraft and Brooks-Corey models led to reasonable agreements for both coarse- andmedium-textured soils, while the latter showed applicability to a broader texture range. In contrast, Rieu-Sposito model was more suitable for fine-textured soils. Fractal models produced a better estimation of watercontents at low pressure heads than at high pressure heads.展开更多
The surface morphology of Ti-Mg supported catalyst and the polyethylene particles are studied using scanning electron microscope(SEM) technology.The results show that either the catalyst's surface or polymer parti...The surface morphology of Ti-Mg supported catalyst and the polyethylene particles are studied using scanning electron microscope(SEM) technology.The results show that either the catalyst's surface or polymer particle's surface is irregular and has fractal characteristics,which can be described by fractal parameter.The more interesting discovery is that the surface fractal dimension values of the polymer particles vary periodically with the polymerization time.We call this phenomenon fractal evolution,which can be divided into the 'revolution' stage and the 'evolution' stage,And then we present polymerization fractal growing model(PFGM),and successfully describe and /or predict the whole evolving process of the polyethylene particle morphology under the different slurry polymerization(including pre-polymerization) conditions without H2.展开更多
The paper presents a novel hydraulic fracturing model for the characterization and simulation of the complex fracture network in shale gas reservoirs. We go beyond the existing method that uses planar or orthogonal co...The paper presents a novel hydraulic fracturing model for the characterization and simulation of the complex fracture network in shale gas reservoirs. We go beyond the existing method that uses planar or orthogonal conjugate fractures for representing the ‘‘complexity'' of the network. Bifurcation of fractures is performed utilizing the Lindenmayer system based on fractal geometry to describe the fracture propagation pattern, density and network connectivity. Four controlling parameters are proposed to describe the details of complex fractures and stimulated reservoir volume(SRV). The results show that due to the multilevel feature of fractal fractures, the model could provide a simple method for contributing reservoir volume calibration. The primary-and second-stage fracture networks across the overall SRV are the main contributions to the production, while the induced fracture network just contributes another 20% in the late producing period. We also conduct simulation with respect to different refracturing cases and find that increasing the complexity of the fracture network provides better performance than only enhancing the fracture conductivity.展开更多
A fractal pore diffusion model of fiuidS in porous media which is in good agreement with the experimental data of the coke-CO2 reaction, has been derived by using the Mandelbrot’s fractal length-area relation. Based ...A fractal pore diffusion model of fiuidS in porous media which is in good agreement with the experimental data of the coke-CO2 reaction, has been derived by using the Mandelbrot’s fractal length-area relation. Based on the model, a new formula and its interpretation about the tortuosity of pore structures of a porous medium have been suggested, from which the fructal pore dthesion resistance has been defined. The resistance ascends obviously with the fmctal pore dimension and the conversion rutio increasing, especially in the middle-latter period of fiuid-solid reactions.展开更多
With the aim to probe the effects of the microscopic details of fractal substrates on the scaling of discrete growth models, the surface structures of the equilibrium restricted curvature(ERC) model on Sierpinski arro...With the aim to probe the effects of the microscopic details of fractal substrates on the scaling of discrete growth models, the surface structures of the equilibrium restricted curvature(ERC) model on Sierpinski arrowhead and crab substrates are analyzed by means of Monte Carlo simulations. These two fractal substrates have the same fractal dimension df, but possess different dynamic exponents of random walk zrw. The results show that the surface structure of the ERC model on fractal substrates are related to not only the fractal dimension df, but also to the microscopic structures of the substrates expressed by the dynamic exponent of random walk zrw. The ERC model growing on the two substrates follows the well-known Family–Vicsek scaling law and satisfies the scaling relations 2α + df≈ z ≈ 2zrw. In addition, the values of the scaling exponents are in good agreement with the analytical prediction of the fractional Mullins–Herring equation.展开更多
The seepage under a dam foundation is mainly controlled by the performance of the curtain.Its anti-seepage behavior may be weakened by the long term physic-chemical actions from groundwater.According to seepage hydrau...The seepage under a dam foundation is mainly controlled by the performance of the curtain.Its anti-seepage behavior may be weakened by the long term physic-chemical actions from groundwater.According to seepage hydraulics and geochemistry theory,a coupling model for assessing the behavior of the curtain under a dam foundation is set up,which consists of seepage module,solute transport module,geochemistry module and curtain erosion module,solved by FEM.A case study was carried out.The result shows that the curtain efficiency is weakened all the time.Aqueous calcium from the curtain is always in dissolution during the stress period for simulation,which leads to the increasing amount in groundwater reaching 846.35-865.312 g/m3.Within the domain,reaction extent differs in different parts of the curtain.The dissolution of Ca(OH)2 accounts to 877.884 g/m3 near the bottom and is much higher than that of the other parts.The erosion is much more serious near the bottom of the curtain than the other parts,which is the same to the upstream and downstream.Calcium dissolution is mainly controlled by hydraulic condition and dispersion,and it varies in a non-linear way within the domain.展开更多
The induced polarization response of an environment presenting cylindrical layers was obtained. The fractal model for complex resistivity was employed as an intrinsic property of the polarizable layers. The influence ...The induced polarization response of an environment presenting cylindrical layers was obtained. The fractal model for complex resistivity was employed as an intrinsic property of the polarizable layers. The influence of the model fractal parameters on the electromagnetic response was investigated. The results demonstrated that the fractal parameters dominate the apparent resistivity phase response;measurements of the induced polarization data allow for the determination of the fractal properties of the environment without noticeable electromagnetic coupling effects at frequencies below 104 Hz.展开更多
文摘The seepage characteristics of multiscale porous media is of considerable significance in many scientific and engineering fields.The Darcy permeability is one of the key macroscopic physical properties to characterize the seepage capacity of porous media.Therefore,based on the statistically fractal scaling law of porous media,fractal geometry is applied to model the multiscale pore structures.And a two-dimensional fractal orifice-throat model with multiscale and tortuous characteristics is proposed for the seepage flow through porous media.The analytical expression for Darcy permeability of porous media is derived,which is validated by comparing with available experimental data.The results show that the Darcy permeability is significantly influenced by porosity,orifice-throat fractal dimension,minimum to maximum diameter ratio,orifice-throat ratio and tortuosity fractal dimension.The present results are helpful for understanding the seepage mechanism of multiscale porous media,and may provide theoretical basis for unconventional oil and gas exploration and development,porous phase transition energy storage composites,CO2 geological sequestration,environmental protection and nuclear waste treatment,etc.
文摘The Indo-Gangetic Plain(IGP)is one of the most seismically vulnerable areas due to its proximity to the Himalayas.Geographic information system(GIS)-based seismic characterization of the IGP was performed based on the degree of deformation and fractal dimension.The zone between the Main Boundary Thrust(MBT)and the Main Central Thrust(MCT)in the Himalayan Mountain Range(HMR)experienced large variations in earthquake magnitude,which were identified by Number-Size(NS)fractal modeling.The central IGP zone experienced only moderate to low mainshock levels.Fractal analysis of earthquake epicenters reveals a large scattering of earthquake epicenters in the HMR and central IGP zones.Similarly,the fault fractal analysis identifies the HMR,central IGP,and south-western IGP zones as having more faults.Overall,the seismicity of the study region is strong in the central IGP,south-western IGP,and HMR zones,moderate in the western and southern IGP,and low in the northern,eastern,and south-eastern IGP zones.
基金supported by the National Natural Science Youth Foundation of China(Grant No.51309101)the Henan Province Major Scientific and Technological Projects(Grant No.172102210372)the Cooperative Project of Production,Teaching and Research in Henan Province(Grant No.18210700031)
文摘This research focused on the three-dimensional(3 D) seepage field simulation of a high concrete-faced rockfill dam(CFRD) under complex hydraulic conditions. A generalized equivalent continuum model of fractured rock mass was used for equivalent continuous seepage field analysis based on the improved node virtual flow method. Using a high CFRD as an example, the generalized equivalent continuum range was determined, and a finite element model was established based on the terrain and geological conditions, as well as structural face characteristics of the dam area. The equivalent seepage coefficients of different material zones or positions in the dam foundation were calculated with the Snow model or inverse analysis. Then, the 3 D seepage field in the dam area was calculated under the normal water storage conditions, and the corresponding water head distribution, seepage flow, seepage gradient, and seepage characteristics in the dam area were analyzed. The results show that the generalized equivalent continuum model can effectively simulate overall seepage patterns of the CFRD under complex hydraulic conditions and provide a reference for seepage analysis of similar CFRDs.
基金The authors acknowledge the support of the National Key Basic Research Project No.G1999043206“Advanced School Key Teachers Supporting Program”of the Ministry of Education,the National Climbing Program of China No.95-pre-25 and 95-pre-39the“100 Trans-Century Science and Technology Talented Persons Cultivating Program”Foundation of the Ministry of Land and Mineral Resources No.9808.
文摘Based on an analysis of the fractal structures and mass transport mechanism of typical shear-fluid-ore formation system, the fractal dispersion theory of the fluid system was used in the dynamic study of the ore formation system. The model of point-source diffusive illuviation of the shear-fluid-ore formation system was constructed, and the numerical simulation of dynamics of the ore formation system was finished. The result shows that: (1) The metallogenic system have nested fractal structure. Different fractal dimension values in different systems show unbalance and inhomogeneity of ore-forming processes in the geohistory. It is an important parameter to symbolize the process of remobilization and accumulation of ore-forming materials. Also it can indicate the dynamics of the metallogenic system quantitatively to some extent. (2) In essence, the fractal dispersive ore-forming dynamics is a combination of multi-processes dominated by fluid dynamics and supplemented by molecule dispersion in fluids and fluid-rock interaction. It changes components and physico-chemical properties of primary rocks and fluids, favouring deposition and mineralization of ore-forming materials. (3) Gold ore-forming processes in different types of shear zones are quite different. (1) In a metallogenic system with inhomogeneous volumetric change and inhomogeneous shear, mineralization occurs in structural barriers in the centre of a shear zone and in geochemical barriers in the shear zone near its boundaries. But there is little possibility of mineralization out of the shear zone. (2) As to a metallogenic system with inhomogeneous volumetric change and simple shear, mineralization may occur only in structural barriers near the centre of the shear zone. (3) In a metallogenic system with homogeneous volumetric change and inhomogeneous shear, mineralization may occur in geochemical barriers both within and out of the shear zone.
基金supported by the National Natural Science Foundation of China(Grant No.51709021)the Open Foundation of the State Key Laboratory of Hydrology-Water Resources and Hydraulic Engineering(Grant No.2016491111)
文摘Affected by external environmental factors and evolution of dam performance, dam seepage behavior shows nonlinear time-varying characteristics. In this study, to predict and evaluate the long-term development trend and short-term fluctuation of the dam seepage behavior, two monitoring models were developed, one for the base flow effect and one for daily variation of dam seepage elements. In the first model, to avoid the influence of the time lag effect on the evaluation of seepage variation with the time effect component of seepage elements, the base values of the seepage element and the reservoir water level were extracted using the wavelet multi-resolution analysis method, and the time effect component was separated by the established base flow effect monitoring model. For the development of the daily variation monitoring model for dam seepage elements, all the previous factors, of which the measured time series prior to the dam seepage element monitoring time may have certain influence on the monitored results, were considered. Those factors that were positively correlated with the analyzed seepage element were initially considered to be the support vector machine(SVM) model input factors, and then the SVM kernel function-based sensitivity analysis was performed to optimize the input factor set and establish the optimized daily variation SVM model. The efficiency and rationality of the two models were verified by case studies of the water level of two piezometric tubes buried under the slope of a concrete gravity dam.Sensitivity analysis of the optimized SVM model shows that the influences of the daily variation of the upstream reservoir water level and rainfall on the daily variation of piezometric tube water level are processes subject to normal distribution.
基金supported by the National Natural Science Foundation of China(Grants No.51179108 and 51679151)the Special Fund for the Public Welfare Industry of the Ministry of Water Resources of China(Grant No.201501033)+1 种基金the National Key Research and Development Program(Grant No.2016YFC0401603)the Program Sponsored for Scientific Innovation Research of College Graduates in Jiangsu Province(Grant No.KYZZ15_0140)
文摘Extreme hydrological events induced by typhoons in reservoir areas have presented severe challenges to the safe operation of hydraulic structures. Based on analysis of the seepage characteristics of an earth rock dam, a novel seepage safety monitoring model was constructed in this study. The nonlinear influence processes of the antecedent reservoir water level and rainfall were assumed to follow normal distributions.The particle swarm optimization(PSO) algorithm was used to optimize the model parameters so as to raise the fitting accuracy. In addition, a mutation factor was introduced to simulate the sudden increase in the piezometric level induced by short-duration heavy rainfall and the possible historical extreme reservoir water level during a typhoon. In order to verify the efficacy of this model, the earth rock dam of the Siminghu Reservoir was used as an example. The piezometric level at the SW1-2 measuring point during Typhoon Fitow in 2013 was fitted with the present model, and a corresponding theoretical expression was established. Comparison of fitting results of the piezometric level obtained from the present statistical model and traditional statistical model with monitored values during the typhoon shows that the present model has a higher fitting accuracy and can simulate the uprush feature of the seepage pressure during the typhoon perfectly.
基金Supported by National Natural Science Foundation of China(Grant No.51775475)Hebei Provincial Natural Science Foundation of China(Grant No.E2016203463)
文摘The contact sti ness of a mechanical bonding surface is an important parameter in determining the normal and radial contact force. To improve the calculation accuracy of the contact force model, the surface roughness of the bonding surface and the energy loss that necessarily occurs during the impact process should be considered com?prehensively. To study the normal contact force of a revolute joint with clearance more accurately in the case of dry friction, a nonlinear sti ness coe cient model considering the surface roughness was established based on fractal theory, which considers the elastic, elastic?plastic, and plastic deformations of the asperities of the contact surface during the contact process. On this basis, a modified nonlinear spring damping model was established based on the Lankarani–Nikravesh contact force model. The laws influencing the surface roughness, recovery coe cient, initial velocity, and clearance size on the impact force were revealed, and were compared with the Lankarani–Nikravesh model and a hybrid model using MATLAB. The maximum impact force was obtained using a modified contact force model under di erent initial velocities, di erent clearances, and di erent degrees of surface roughness, and the calculated results were then compared with the experiment results. This study indicates that the modified model can be used more widely than other models, and is suitable for both large and small clearances. In particular, the modified model is more accurate when calculating the contact force of a revolute joint with a small clearance.
基金supported by the Natural Science Foundation of Hebei Province(No.E2021502025)。
文摘Establishing a long air gap discharge model considering the streamer-leader transition and randomness of the discharge path is of great signiflcance to improve the accuracy of discharge characteristic prediction and optimize external insulation design.Based on fractal theory and thermal ionization theory of streamer-leader transition,this work establishes a dynamic development model for the long air gap discharge streamer-leader system,which includes streamer inception,streamer development,leader inception,development of streamer-leader system and flnal jump.The positive discharge process of a 3 m rod plate is simulated to obtain the fractal distribution of the discharge path and the law of leader development for comparison with the discharge test results.The results show that the simulation model is similar to test results in the development characteristics of leader path distribution,each stage time and leader velocity.Finally,a simulation calculation of a 50%breakdown voltage of the rod-plate gap and ball-plate gap is carried out,with results fairly consistent with test data,proving the effectiveness and practicality of the model.
基金Supported by National Natural Science Foundation of China(Grant Nos.51105304,51475364)Shaanxi Provincial Natural Science Basic Research Plan of China(Grant No.2015JM5212)
文摘Because the result of the MB fractal model contradicts with the classical contact mechanics, a revised elastoplastic contact model of a single asperity is developed based on fractal theory. The critical areas of a single asperity are scale dependent, with an increase in the contact load and contact area, a transition from elastic, elastoplastic to full plastic deformation takes place in this order. In considering the size distribution function, analytic expression between the total contact load and the real contact area on the contact surface is obtained. The elastic, elastoplastic and full plastic contact load are obtained by the critical elastic contact area of the biggest asperity and maximun contact area of a single asperity. The results show that a rough surface is firstly in elastic deformation. As the load increases, elastoplastic or full plastic deformation takes place. For constant characteristic length scale G, the slope of load-area relation is proportional to fractal dimension D. For constant fractal dimension D, the slope of load-area relation is inversely proportional to G. For constant D and G, the slope of load-area relation is inversely proportional to property of the material ? , namely with the same load, the material of rough surface is softer, and the total contact area is larger. The contact mechanics model provides a foundation for study of the friction, wear and seal performance of rough surfaces.
基金supported by National Natural Science Foundation of China (Grant Nos. 50975276,50475164)National Basic Research Program of China (973 Program,Grant No. 2007CB607605)+1 种基金Doctoral Programs Foundation of Ministry of Education of China (Grant No.200802900513)Priority Academic Program Development of Jiangsu Higher Education Institutions of China (PAPD)
文摘The thermal contact conductance problem is an important issue in studying the heat transfer of engineering surfaces,which has been widely studied since last few decades,and for predicting which many theoretical models have been established.However,the models which have been existed are lack of objectivity due to that they are mostly studied based on the statistical methodology characterization for rough surfaces and simple partition for the deformation formats of contact asperity.In this paper,a fractal prediction model is developed for the thermal contact conductance between two rough surfaces based on the rough surface being described by three-dimensional Weierstrass and Mandelbrot fractal function and assuming that there are three kinds of asperity deformation modes:elastic,elastoplastic and fully plastic.Influences of contact load and contact area as well as fractal parameters and material properties on the thermal contact conductance are investigated by using the presented model.The investigation results show that the thermal contact conductance increases with the increasing of the contact load and contact area.The larger the fractal dimension,or the smaller the fractal roughness,the larger the thermal contact conductance is.The thermal contact conductance increases with decreasing the ratio of Young's elastic modulus to the microhardness.The results obtained indicate that the proposed model can effectively predict the thermal contact conductance at the interface,which provide certain reference to the further study on the issue of heat transfer between contact surfaces.
文摘The target in this investigation is separation and delineation of geochemical anomalies for the single element Cu in Mesgaran mining area, eastern Iran. Mesgaran mining area is located in south part of Sarbishe county with about 29 Km distance to the county center. This region is part of an Ophiolite sequence and the copper anomalies seem to be related to a volcanic massive sulfide (VMS) deposit whose main part (massive sulfide Lens) has been eroded. In order to delineate Cu anomalies, the boxplot as an Exploratory Data Analysis (EDA) method and concentration-volume (C-V) Fractal modeling are employed. Both of the methods reveal low-deep anomalies which are highly correlated with geological and geophysical studies. As the main result of this study we show that Fractal modeling in spite of the Boxplot, is not recommended for complex geological settings. The proved shallow anomalies recorded by geophysical studies and defined by the used methods are in accordance to the stringer zone of a volcanic massive sulfide (VMS) deposit in Mesgaran mining area which means this region is the bottom of a VMS deposit and geochemical anomalies are related to the remained parts of the deposit.
基金Project supported by the National Natural Science Foundation of China (No, 49971041), the National Key Basic Research Support Foundation (NKBRSF) of China (No. G1999011803) the Director Foundation of the Institute of Soil Science, CAS (No. ISSDF0004).
文摘Soil water retention characteristics are the key information required in hydrological modeling. Frac-tal models provide a practical alternative for indirectly estimating soil water retention characteristics fromparticle-size distribution data. Predictive capabilities of three fractal models, i.e, Tyler-Wheatcraft model,Rieu-Sposito model, and Brooks-Corey model, were fully evaluated in this work using experimental datafrom an international database and literature. Particle-size distribution data were firstly interpolated into20 classes using a van Genuchten-type equation. Fractal dimensions of the tortuous pore wall and the poresurface were then calculated from the detailed particle-size distribution and incorporated as a parameter infractal water retention models. Comparisons between measured and model-estimated water retention cha-racteristics indicated that these three models were applicable to relatively different soil textures and pressurehead ranges. Tyler-Wheatcraft and Brooks-Corey models led to reasonable agreements for both coarse- andmedium-textured soils, while the latter showed applicability to a broader texture range. In contrast, Rieu-Sposito model was more suitable for fine-textured soils. Fractal models produced a better estimation of watercontents at low pressure heads than at high pressure heads.
基金Supported by the National Natural Science Foundation of China (No. 29706010, No. 20203016).
文摘The surface morphology of Ti-Mg supported catalyst and the polyethylene particles are studied using scanning electron microscope(SEM) technology.The results show that either the catalyst's surface or polymer particle's surface is irregular and has fractal characteristics,which can be described by fractal parameter.The more interesting discovery is that the surface fractal dimension values of the polymer particles vary periodically with the polymerization time.We call this phenomenon fractal evolution,which can be divided into the 'revolution' stage and the 'evolution' stage,And then we present polymerization fractal growing model(PFGM),and successfully describe and /or predict the whole evolving process of the polyethylene particle morphology under the different slurry polymerization(including pre-polymerization) conditions without H2.
基金supported by National Natural Science Foundation of China(No.51674279)China Postdoctoral Science Foundation(No.2016M602227)a grant from National Science and Technology Major Project(No.2017ZX05049-006)
文摘The paper presents a novel hydraulic fracturing model for the characterization and simulation of the complex fracture network in shale gas reservoirs. We go beyond the existing method that uses planar or orthogonal conjugate fractures for representing the ‘‘complexity'' of the network. Bifurcation of fractures is performed utilizing the Lindenmayer system based on fractal geometry to describe the fracture propagation pattern, density and network connectivity. Four controlling parameters are proposed to describe the details of complex fractures and stimulated reservoir volume(SRV). The results show that due to the multilevel feature of fractal fractures, the model could provide a simple method for contributing reservoir volume calibration. The primary-and second-stage fracture networks across the overall SRV are the main contributions to the production, while the induced fracture network just contributes another 20% in the late producing period. We also conduct simulation with respect to different refracturing cases and find that increasing the complexity of the fracture network provides better performance than only enhancing the fracture conductivity.
文摘A fractal pore diffusion model of fiuidS in porous media which is in good agreement with the experimental data of the coke-CO2 reaction, has been derived by using the Mandelbrot’s fractal length-area relation. Based on the model, a new formula and its interpretation about the tortuosity of pore structures of a porous medium have been suggested, from which the fructal pore dthesion resistance has been defined. The resistance ascends obviously with the fmctal pore dimension and the conversion rutio increasing, especially in the middle-latter period of fiuid-solid reactions.
基金Project support by the Fundamental Research Funds for the Central Universities of Ministry of Education of China(Grant No.2013XK04)
文摘With the aim to probe the effects of the microscopic details of fractal substrates on the scaling of discrete growth models, the surface structures of the equilibrium restricted curvature(ERC) model on Sierpinski arrowhead and crab substrates are analyzed by means of Monte Carlo simulations. These two fractal substrates have the same fractal dimension df, but possess different dynamic exponents of random walk zrw. The results show that the surface structure of the ERC model on fractal substrates are related to not only the fractal dimension df, but also to the microscopic structures of the substrates expressed by the dynamic exponent of random walk zrw. The ERC model growing on the two substrates follows the well-known Family–Vicsek scaling law and satisfies the scaling relations 2α + df≈ z ≈ 2zrw. In addition, the values of the scaling exponents are in good agreement with the analytical prediction of the fractional Mullins–Herring equation.
基金Project(50139030) supported by the National Natural Science Foundation of ChinaProject(501072) supported by the Scientific Research Foundation for the Returned Overseas Scholars of the Ministry of Education of China
文摘The seepage under a dam foundation is mainly controlled by the performance of the curtain.Its anti-seepage behavior may be weakened by the long term physic-chemical actions from groundwater.According to seepage hydraulics and geochemistry theory,a coupling model for assessing the behavior of the curtain under a dam foundation is set up,which consists of seepage module,solute transport module,geochemistry module and curtain erosion module,solved by FEM.A case study was carried out.The result shows that the curtain efficiency is weakened all the time.Aqueous calcium from the curtain is always in dissolution during the stress period for simulation,which leads to the increasing amount in groundwater reaching 846.35-865.312 g/m3.Within the domain,reaction extent differs in different parts of the curtain.The dissolution of Ca(OH)2 accounts to 877.884 g/m3 near the bottom and is much higher than that of the other parts.The erosion is much more serious near the bottom of the curtain than the other parts,which is the same to the upstream and downstream.Calcium dissolution is mainly controlled by hydraulic condition and dispersion,and it varies in a non-linear way within the domain.
文摘The induced polarization response of an environment presenting cylindrical layers was obtained. The fractal model for complex resistivity was employed as an intrinsic property of the polarizable layers. The influence of the model fractal parameters on the electromagnetic response was investigated. The results demonstrated that the fractal parameters dominate the apparent resistivity phase response;measurements of the induced polarization data allow for the determination of the fractal properties of the environment without noticeable electromagnetic coupling effects at frequencies below 104 Hz.
