Design and Development of a Parabolic Trough Solar Air Heater (PTSAH) for a Greenhouse Dryer (GD) was done to improve the dryer’s performance. The materials used for the fabrication of the PTSAH included galvanized s...Design and Development of a Parabolic Trough Solar Air Heater (PTSAH) for a Greenhouse Dryer (GD) was done to improve the dryer’s performance. The materials used for the fabrication of the PTSAH included galvanized sheets covered with aluminium foil, an absorber tube made of GI pipe painted matt black to increase heat absorbance at the focal line, mild steel square tubes, shutter plywood, and an axial fan to push air through the absorber tube. Key geometrical parameters used for the design of the PTSAH were a rim angle of 98 degrees, focal length of 0.2608 m, height of 0.3451 m, length of 2 m, and an aperture width of 1.2 m. The PTSAH’s total aperture surface area was 2.4 m2, while its absorber tube surface area was 0.1587 m2. The PTSAH was experimentally tested to establish its thermal performance. It was found that the ambient air recorded an average value of 31.1˚C and that the air heater could increase the air temperature by 45.6˚C above ambient with a thermal efficiency of 5.3%. It can, therefore, be concluded that the PTSAH can significantly improve the performance of a GD by supplying the GD with air at a higher temperature than ambient.展开更多
The principle and development prospect of air source heat pump water heat were introduced,as well as the designation of condenser (storage water tank),experimental study on installations was also carried out.The resul...The principle and development prospect of air source heat pump water heat were introduced,as well as the designation of condenser (storage water tank),experimental study on installations was also carried out.The results showed that air source heat pump water heater was superior to conventional system.Under the operation of cooling and heating,heat pump comprehensive utilization equipment could improve heating performance,reduce energy consumption,and recycle condensing heat to provide hot water.展开更多
The paper presents an experimental study on the heat transfer and flow friction characteristics in a solar air heater channel fitted with delta-winglet type vortex generators （DWs）. The experiments are conducted by ...The paper presents an experimental study on the heat transfer and flow friction characteristics in a solar air heater channel fitted with delta-winglet type vortex generators （DWs）. The experiments are conducted by varying the airflow rate for Reynolds number in the range of 5000 to 24000 in the test section with a uniform heat-flux applied on the upper channel wall. Firstly, the DW pairs are mounted only at the entrance of the lower wall of the test channel （called DW-E） to create multiple vortex flows at the entry. The effect of two transverse pitches （Re= Pt/H= 1 and 2） at three attack angles （a= 30°, 45° and 60°） of the DW-E with its relative height, b/H= 0.5 （half height of channel） is examined. Secondly, the 30° DWs with three different relative heights （blH = 0.3, 0.4 and 0.5） are placed on the upper wall only （absorber plate, called DW-A） of the test channel. The experimental result reveals that in the first case, the 60° DW-E at Rp = 1 provides the highest heat transfer and friction factor while the 30° DW-E at Rp = 1 performs overall better than the others. In the second case, the 30° DW-A at b/H= 0.5 yields the highest heat transfer and friction factor but the best thermal performance is found at b/H = 0.4.展开更多
This paper explains the experimental performance evaluation of a Corrugated Type Solar Air Heater(CTSAH)for understanding its performance in a humid tropical climatic condition in Puducherry,India.This helps in unders...This paper explains the experimental performance evaluation of a Corrugated Type Solar Air Heater(CTSAH)for understanding its performance in a humid tropical climatic condition in Puducherry,India.This helps in understanding its effectiveness in using it for drying application of products like seafood,etc.Experiments were conducted at different mass flow rates and their effect on the heat gain,efficiency,friction factor heat transfer,etc.,was analyzed.Experiments were carried out at different mass flow rates,i.e.,M1=0.06 kg/s,M2=0.14 kg/s,M3=0.17 kg/s,M4=0.25 kg/s,M5=0.3 kg/s,and were conducted from 11:00 h to 14:00 h.The air inlet&air temperature is found to be at an average of 40°C whereas the incident solar radiation is at an average of 795 W/m2.Experimental results show that the optimum performance of the CTSAH is in the mass flow rate range of 0.14–0.25(kg/s).Also,the calculated useful heat produced,convective heat transfer coefficients,effective efficiency,optical efficiency provides knowledge on the potential use of the air heater.展开更多
Biodiesel （BD） was made from animal-fats reacting with methanol and potassium hydroxide in the laboratory. The biodiesel made in the laboratory was sent to K-petro, the government agency to inspect the quality of an...Biodiesel （BD） was made from animal-fats reacting with methanol and potassium hydroxide in the laboratory. The biodiesel made in the laboratory was sent to K-petro, the government agency to inspect the quality of animal-fats biodiesel, of which generally the quality was acceptable for heating oil for agricultural hot air heater. Kinematic viscosity and calorific values of the biodiesels were measured. BD20（K）, kerosene based biodiesel, showed 18 cSt at -20 ~C. It seems that BD100 can not be suitable for heating fuel under some temperature. As BD content increased calorific value decreased up to 40,000 J/g for 100% BD （BD100） while, light oil calorific value was 45,567 J/g, showing difference of 5,567 J/g （about 12% difference）, Several different fuels including BD20 （biodiesel 20% ＋ light oil 80%）, BD50 （biodiesel 50% ＋ light oil 50%）, BD100 （biodiesel 100%） and light oil were prepared and tested for fuel combustion qualities for agricultural hot air heater and their combustion performances were compared and analyzed. Flame dimensions of biodiesels and light oil were almost same shape at the same combustion condition in the burner of the hot air heater. Generally, CO2 amounts of BDs were greater than light oil, but the differences were so small that it is hard to tell there was significant difference between the BDs combustion and light oil.展开更多
Solar energy is regarded as one of the promising renewable energy sources in the world.The main aim of this study is to use the Taguchi-Grey relational grade analysis to optimize the performance of two Solar Air Heate...Solar energy is regarded as one of the promising renewable energy sources in the world.The main aim of this study is to use the Taguchi-Grey relational grade analysis to optimize the performance of two Solar Air Heaters(SAHs).A typical Grey–Taguchi method was applied.The Orthogonal Array,Signal-to-Noise ratio,Grey Relational Grade,and Analysis of Variance were employed to investigate the performance characteristics of SAH.Experimental observations were made in agreement with Jordanian climate 32°00′N latitude and 36°00′E longitude with a solar intensity of 500 W\m^(2).The operating factors selected for optimization are the tilt angle(T)with three levels(0°,22°,45°),inlet velocity(V)with two levels(1.2,1.8 m/s),and absorber plate material(M)with two levels(Aluminum,wood).In this study,the Grey–Taguchi approach is validated by performing 12 individual experiments.The results show that the process factors sequence required for a maximum SAH efficiency(SAHµ)is V>T>M.Using this approach,we combined the Orthogonal Array design with Grey Relational Analysis.As a result of that,the level of each operating conditions which optimizes both process responses(Temperature difference,ΔT and Solar air heater efficiency,SAHµ)can be specified with a minimum number of tests compared with classic Grey Relational Analysis.The optimal operating conditions of a SAH for multiple performance characteristics are determined as T2,M2,and V2,respectively,which are in congruence with the experimental results.展开更多
The reasons of introducing cold air into pulverizer are analyzed for boilers with large capacity and high parameters. The temperature rises of the exhaust gas are calculated when varying the amount of the cold air. Th...The reasons of introducing cold air into pulverizer are analyzed for boilers with large capacity and high parameters. The temperature rises of the exhaust gas are calculated when varying the amount of the cold air. The hot primary air heater, a new technology, is developed to eliminate the cold air from the pulverized coal system. The applications, advantages and disadvantages are introduced in detail for the new device and system. It is concluded that introducing cold air into pulverizer is one of the major factors that causes the exhaust gas temperature of boilers with large capacity to be high. The amount of the cold air could be reduced signif icantly, even to zero in some cases by adopting the hot primary air heater, which drops the exhaust gas temperature of the boiler effectively. The hot primary air heater, which could play part roles of the steam-air heater or the hot air recirculation system, could also be used to adjust the exhaust gas temperature within the range of 20 ℃ by controlling the flow rate of the cooling medium. Moreover, the startup period of the steam-air heater or the hot air recirculation system will be shortened, which is a unique advantage of the hot primary air heater among the measures to drop the exhaust gas temperature.展开更多
An experimental investigation was conducted to measure the temperature variation across the flow channel and to determine the performance of a natural convection solar air heater at various tilt angles from 15, 30 and...An experimental investigation was conducted to measure the temperature variation across the flow channel and to determine the performance of a natural convection solar air heater at various tilt angles from 15, 30 and 45°. The results of the temperature profile across the air gap showed that heat transfer from the absorber plate to the air stream was mainly by convection. At a particular section, mean air temperature could be calculated from the arithmetic mean of the temperature profile across the air gap to within ± 2 ℃. The axial air temperature distribution was non linear and did not increase much beyond 1 m of collector length. It tended to decrease towards the end of the collector. Overall glass, absorber plate and mean air temperatures over the entire length of the solar air heater could be determined by averaging the mean axial temperatures to within ± 2 ℃. The heater performed better as inclination increased.展开更多
A novel design of Return Flow Solar Air Heater(RFSAH)with different arrangements of baffles especially V-Type Artificial roughness is simulated and numerically analyzed with energy balance equations.To enhance the eff...A novel design of Return Flow Solar Air Heater(RFSAH)with different arrangements of baffles especially V-Type Artificial roughness is simulated and numerically analyzed with energy balance equations.To enhance the effectiveness of baffles,numerous studies have been conducted.The performance of the RFSAH is studied in terms of thermal efficiency,thermo-hydraulic efficiency,and optimization of baffle parameters.Maximum Thermal efficiency and thermo-hydraulic efficiency are found in RFSAH with baffle on both sides of the absorber plate and mass flow rate above 0.2kg/s.Sensitivity analysis of the influencing parameters is carried out and reported the best performance of the system on selective geometrical parameters(ψ=0.7,β=20%,e/H=1,p/e=0.8,α=60°).The results obtained from the present model are validated with the published experimental results and have been found in quite reasonable agreement with an average error of 16.45%.Thermal and Thermohydraulic efficiency of RFSAH with a baffle on both sides of the absorber plate is maximum among baffles below,above,and on both sides of the absorber plate.It is observed that the thermal efficiency of RFSAH is greater than SF-SAH.The proposed optimum baffles roughness is suggested to increase the air upholding time period for more efficient output.展开更多
In this research paper,a solar air heater with triangular fins has been experimentally analysed and optimized.Initially,an experimental set-up of a solar air heater having triangular fins has been developed at the loc...In this research paper,a solar air heater with triangular fins has been experimentally analysed and optimized.Initially,an experimental set-up of a solar air heater having triangular fins has been developed at the location of 28.10°N,78.23°E.The heat transfer rate through fins and fins efficiency has been determined by the Finite Difference Method model equations.The experimental data and modeled data of response parameters have been optimized in MINITAB-17 software by the Response Surface Methodology tool.For creating the response surface design,three input parameters have been selected namely solar intensity,Reynolds number,and fin base-to-height ratio.The range of solar intensity,Reynolds number,and fin base-to-height ratio is 600 to 1000W/m^(2),4000 to 6000,and 0.4 to 0.8 respectively.The response surface design has been analyzed by calculating the outlet temperature,friction factor,Nusselt number,fin efficiency,thermal performance factor,and exergy efficiency.The optimum settings of input parameters:solar intensity is 1000 W/m^(2);Reynolds number is 4969.7,and the fin base to height ratio is 0.6060,on which these response:namely outlet temperature of 92.531℃,friction factor of 0.2350,Nusselt number of 127.761,thermal efficiency of 50.836%,thermal performance factor of 1.4947,and exergy efficiency of 8.762%.展开更多
Solar air heaters(SAHs)are widely used solar thermal systems with applications in diverse sectors.However,its effectiveness is re-strained by low convective heat transfer(HT)coefficients at the absorber plate,leading ...Solar air heaters(SAHs)are widely used solar thermal systems with applications in diverse sectors.However,its effectiveness is re-strained by low convective heat transfer(HT)coefficients at the absorber plate,leading to inefficient HT,and the elevated temperature of the absorber plate causes significant heat losses,reducing thermal efficiency.This study addresses these challenges by introducing ribs or roughness on the absorber plate creating turbulence in the airflow,resulting in significant improvements.The research inves-tigates various rib configurations,the influence of rib parameters,performance methods,and arrangements to evaluate their HT and friction characteristics.Among these rib configurations,a comparative analysis is done on various factors such as the Nusselt number ratio,thermal enhancement factor,friction factor ratio,and thermal efficiency to optimize distinct roughness parameters and rib ar-rangement patterns.This study also provides valuable recommendations from existing literature,offering insights into the effective design,prospects,and implementation of SAH systems.展开更多
A new type of microchannel condenser applied in the air source heat pump water heater(ASHPWH)with cyclic heating was proposed in this study.The operating performance of the ASHPWH was frst tested.Then,the structure of...A new type of microchannel condenser applied in the air source heat pump water heater(ASHPWH)with cyclic heating was proposed in this study.The operating performance of the ASHPWH was frst tested.Then,the structure of the microchannel condenser was optimized with the implement of vortex generators.Finally,a numerical model of the ASHPWH was established and the optimized microchannel condenser was studied.The experimental results showed that the average coefficient of performance(COP)of the 1HP(735 W)ASHPWH reached 3.48.In addition,the optimized microchannel condenser could be matched with a 3 HP(2430W)ASHPWH with an average heating capacity of 10.30 kW,and achieving an average COP of 4.24,14.6%higher than the limit value in the national standard.展开更多
文摘Design and Development of a Parabolic Trough Solar Air Heater (PTSAH) for a Greenhouse Dryer (GD) was done to improve the dryer’s performance. The materials used for the fabrication of the PTSAH included galvanized sheets covered with aluminium foil, an absorber tube made of GI pipe painted matt black to increase heat absorbance at the focal line, mild steel square tubes, shutter plywood, and an axial fan to push air through the absorber tube. Key geometrical parameters used for the design of the PTSAH were a rim angle of 98 degrees, focal length of 0.2608 m, height of 0.3451 m, length of 2 m, and an aperture width of 1.2 m. The PTSAH’s total aperture surface area was 2.4 m2, while its absorber tube surface area was 0.1587 m2. The PTSAH was experimentally tested to establish its thermal performance. It was found that the ambient air recorded an average value of 31.1˚C and that the air heater could increase the air temperature by 45.6˚C above ambient with a thermal efficiency of 5.3%. It can, therefore, be concluded that the PTSAH can significantly improve the performance of a GD by supplying the GD with air at a higher temperature than ambient.
基金Supported by Scientific Research Fund of Ningxia University [(E) ndzr09-23]
文摘The principle and development prospect of air source heat pump water heat were introduced,as well as the designation of condenser (storage water tank),experimental study on installations was also carried out.The results showed that air source heat pump water heater was superior to conventional system.Under the operation of cooling and heating,heat pump comprehensive utilization equipment could improve heating performance,reduce energy consumption,and recycle condensing heat to provide hot water.
文摘The paper presents an experimental study on the heat transfer and flow friction characteristics in a solar air heater channel fitted with delta-winglet type vortex generators （DWs）. The experiments are conducted by varying the airflow rate for Reynolds number in the range of 5000 to 24000 in the test section with a uniform heat-flux applied on the upper channel wall. Firstly, the DW pairs are mounted only at the entrance of the lower wall of the test channel （called DW-E） to create multiple vortex flows at the entry. The effect of two transverse pitches （Re= Pt/H= 1 and 2） at three attack angles （a= 30°, 45° and 60°） of the DW-E with its relative height, b/H= 0.5 （half height of channel） is examined. Secondly, the 30° DWs with three different relative heights （blH = 0.3, 0.4 and 0.5） are placed on the upper wall only （absorber plate, called DW-A） of the test channel. The experimental result reveals that in the first case, the 60° DW-E at Rp = 1 provides the highest heat transfer and friction factor while the 30° DW-E at Rp = 1 performs overall better than the others. In the second case, the 30° DW-A at b/H= 0.5 yields the highest heat transfer and friction factor but the best thermal performance is found at b/H = 0.4.
基金the Department of Science and Technology,Government of India(www.dst.gov.in)for the Grant No.SR/FTP/ETA-0064/2014 granted to Sreekumar,A.
文摘This paper explains the experimental performance evaluation of a Corrugated Type Solar Air Heater(CTSAH)for understanding its performance in a humid tropical climatic condition in Puducherry,India.This helps in understanding its effectiveness in using it for drying application of products like seafood,etc.Experiments were conducted at different mass flow rates and their effect on the heat gain,efficiency,friction factor heat transfer,etc.,was analyzed.Experiments were carried out at different mass flow rates,i.e.,M1=0.06 kg/s,M2=0.14 kg/s,M3=0.17 kg/s,M4=0.25 kg/s,M5=0.3 kg/s,and were conducted from 11:00 h to 14:00 h.The air inlet&air temperature is found to be at an average of 40°C whereas the incident solar radiation is at an average of 795 W/m2.Experimental results show that the optimum performance of the CTSAH is in the mass flow rate range of 0.14–0.25(kg/s).Also,the calculated useful heat produced,convective heat transfer coefficients,effective efficiency,optical efficiency provides knowledge on the potential use of the air heater.
文摘Biodiesel （BD） was made from animal-fats reacting with methanol and potassium hydroxide in the laboratory. The biodiesel made in the laboratory was sent to K-petro, the government agency to inspect the quality of animal-fats biodiesel, of which generally the quality was acceptable for heating oil for agricultural hot air heater. Kinematic viscosity and calorific values of the biodiesels were measured. BD20（K）, kerosene based biodiesel, showed 18 cSt at -20 ~C. It seems that BD100 can not be suitable for heating fuel under some temperature. As BD content increased calorific value decreased up to 40,000 J/g for 100% BD （BD100） while, light oil calorific value was 45,567 J/g, showing difference of 5,567 J/g （about 12% difference）, Several different fuels including BD20 （biodiesel 20% ＋ light oil 80%）, BD50 （biodiesel 50% ＋ light oil 50%）, BD100 （biodiesel 100%） and light oil were prepared and tested for fuel combustion qualities for agricultural hot air heater and their combustion performances were compared and analyzed. Flame dimensions of biodiesels and light oil were almost same shape at the same combustion condition in the burner of the hot air heater. Generally, CO2 amounts of BDs were greater than light oil, but the differences were so small that it is hard to tell there was significant difference between the BDs combustion and light oil.
文摘Solar energy is regarded as one of the promising renewable energy sources in the world.The main aim of this study is to use the Taguchi-Grey relational grade analysis to optimize the performance of two Solar Air Heaters(SAHs).A typical Grey–Taguchi method was applied.The Orthogonal Array,Signal-to-Noise ratio,Grey Relational Grade,and Analysis of Variance were employed to investigate the performance characteristics of SAH.Experimental observations were made in agreement with Jordanian climate 32°00′N latitude and 36°00′E longitude with a solar intensity of 500 W\m^(2).The operating factors selected for optimization are the tilt angle(T)with three levels(0°,22°,45°),inlet velocity(V)with two levels(1.2,1.8 m/s),and absorber plate material(M)with two levels(Aluminum,wood).In this study,the Grey–Taguchi approach is validated by performing 12 individual experiments.The results show that the process factors sequence required for a maximum SAH efficiency(SAHµ)is V>T>M.Using this approach,we combined the Orthogonal Array design with Grey Relational Analysis.As a result of that,the level of each operating conditions which optimizes both process responses(Temperature difference,ΔT and Solar air heater efficiency,SAHµ)can be specified with a minimum number of tests compared with classic Grey Relational Analysis.The optimal operating conditions of a SAH for multiple performance characteristics are determined as T2,M2,and V2,respectively,which are in congruence with the experimental results.
文摘The reasons of introducing cold air into pulverizer are analyzed for boilers with large capacity and high parameters. The temperature rises of the exhaust gas are calculated when varying the amount of the cold air. The hot primary air heater, a new technology, is developed to eliminate the cold air from the pulverized coal system. The applications, advantages and disadvantages are introduced in detail for the new device and system. It is concluded that introducing cold air into pulverizer is one of the major factors that causes the exhaust gas temperature of boilers with large capacity to be high. The amount of the cold air could be reduced signif icantly, even to zero in some cases by adopting the hot primary air heater, which drops the exhaust gas temperature of the boiler effectively. The hot primary air heater, which could play part roles of the steam-air heater or the hot air recirculation system, could also be used to adjust the exhaust gas temperature within the range of 20 ℃ by controlling the flow rate of the cooling medium. Moreover, the startup period of the steam-air heater or the hot air recirculation system will be shortened, which is a unique advantage of the hot primary air heater among the measures to drop the exhaust gas temperature.
文摘An experimental investigation was conducted to measure the temperature variation across the flow channel and to determine the performance of a natural convection solar air heater at various tilt angles from 15, 30 and 45°. The results of the temperature profile across the air gap showed that heat transfer from the absorber plate to the air stream was mainly by convection. At a particular section, mean air temperature could be calculated from the arithmetic mean of the temperature profile across the air gap to within ± 2 ℃. The axial air temperature distribution was non linear and did not increase much beyond 1 m of collector length. It tended to decrease towards the end of the collector. Overall glass, absorber plate and mean air temperatures over the entire length of the solar air heater could be determined by averaging the mean axial temperatures to within ± 2 ℃. The heater performed better as inclination increased.
文摘A novel design of Return Flow Solar Air Heater(RFSAH)with different arrangements of baffles especially V-Type Artificial roughness is simulated and numerically analyzed with energy balance equations.To enhance the effectiveness of baffles,numerous studies have been conducted.The performance of the RFSAH is studied in terms of thermal efficiency,thermo-hydraulic efficiency,and optimization of baffle parameters.Maximum Thermal efficiency and thermo-hydraulic efficiency are found in RFSAH with baffle on both sides of the absorber plate and mass flow rate above 0.2kg/s.Sensitivity analysis of the influencing parameters is carried out and reported the best performance of the system on selective geometrical parameters(ψ=0.7,β=20%,e/H=1,p/e=0.8,α=60°).The results obtained from the present model are validated with the published experimental results and have been found in quite reasonable agreement with an average error of 16.45%.Thermal and Thermohydraulic efficiency of RFSAH with a baffle on both sides of the absorber plate is maximum among baffles below,above,and on both sides of the absorber plate.It is observed that the thermal efficiency of RFSAH is greater than SF-SAH.The proposed optimum baffles roughness is suggested to increase the air upholding time period for more efficient output.
文摘In this research paper,a solar air heater with triangular fins has been experimentally analysed and optimized.Initially,an experimental set-up of a solar air heater having triangular fins has been developed at the location of 28.10°N,78.23°E.The heat transfer rate through fins and fins efficiency has been determined by the Finite Difference Method model equations.The experimental data and modeled data of response parameters have been optimized in MINITAB-17 software by the Response Surface Methodology tool.For creating the response surface design,three input parameters have been selected namely solar intensity,Reynolds number,and fin base-to-height ratio.The range of solar intensity,Reynolds number,and fin base-to-height ratio is 600 to 1000W/m^(2),4000 to 6000,and 0.4 to 0.8 respectively.The response surface design has been analyzed by calculating the outlet temperature,friction factor,Nusselt number,fin efficiency,thermal performance factor,and exergy efficiency.The optimum settings of input parameters:solar intensity is 1000 W/m^(2);Reynolds number is 4969.7,and the fin base to height ratio is 0.6060,on which these response:namely outlet temperature of 92.531℃,friction factor of 0.2350,Nusselt number of 127.761,thermal efficiency of 50.836%,thermal performance factor of 1.4947,and exergy efficiency of 8.762%.
文摘Solar air heaters(SAHs)are widely used solar thermal systems with applications in diverse sectors.However,its effectiveness is re-strained by low convective heat transfer(HT)coefficients at the absorber plate,leading to inefficient HT,and the elevated temperature of the absorber plate causes significant heat losses,reducing thermal efficiency.This study addresses these challenges by introducing ribs or roughness on the absorber plate creating turbulence in the airflow,resulting in significant improvements.The research inves-tigates various rib configurations,the influence of rib parameters,performance methods,and arrangements to evaluate their HT and friction characteristics.Among these rib configurations,a comparative analysis is done on various factors such as the Nusselt number ratio,thermal enhancement factor,friction factor ratio,and thermal efficiency to optimize distinct roughness parameters and rib ar-rangement patterns.This study also provides valuable recommendations from existing literature,offering insights into the effective design,prospects,and implementation of SAH systems.
基金the National Natural Science Foundation of China(No.51776117)。
文摘A new type of microchannel condenser applied in the air source heat pump water heater(ASHPWH)with cyclic heating was proposed in this study.The operating performance of the ASHPWH was frst tested.Then,the structure of the microchannel condenser was optimized with the implement of vortex generators.Finally,a numerical model of the ASHPWH was established and the optimized microchannel condenser was studied.The experimental results showed that the average coefficient of performance(COP)of the 1HP(735 W)ASHPWH reached 3.48.In addition,the optimized microchannel condenser could be matched with a 3 HP(2430W)ASHPWH with an average heating capacity of 10.30 kW,and achieving an average COP of 4.24,14.6%higher than the limit value in the national standard.
