In this paper,the numerical simulation method is used to study the ballistic performances of hourglass lattice sandwich structures with the same mass under the vertical incidence of fragments.Attention is paid to eluc...In this paper,the numerical simulation method is used to study the ballistic performances of hourglass lattice sandwich structures with the same mass under the vertical incidence of fragments.Attention is paid to elucidating the influences of rod cross-section dimensions,structure height,structure layer,and rod inclination angle on the deformation mode,ballistic performances,and ability to change the ballistic direction of fragments.The results show that the ballistic performances of hourglass lattice sandwich structures are mainly affected by their structural parameters.In this respect,structural parameters optimization of the hourglass lattice sandwich structures enable one to effectively improve their ballistic limit velocity and,consequently,ballistic performances.展开更多
Carbon fiber-reinforced polymer(CFRP)is widely used in aerospace applications.This kind of material may face the threat of high-velocity impact in the process of dedicated service,and the relevant research mainly cons...Carbon fiber-reinforced polymer(CFRP)is widely used in aerospace applications.This kind of material may face the threat of high-velocity impact in the process of dedicated service,and the relevant research mainly considers the impact resistance of the material,and lacks the high-velocity impact damage monitoring research of CFRP.To solve this problem,a real high-velocity impact damage experiment and structural health monitoring(SHM)method of CFRP plate based on piezoelectric guided wave is proposed.The results show that CFRP has obvious perforation damage and fiber breakage when high-velocity impact occurs.It is also proved that guided wave SHM technology can be effectively used in the monitoring of such damage,and the damage can be reflected by quantifying the signal changes and damage index(DI).It provides a reference for further research on guided wave structure monitoring of high/hyper-velocity impact damage of CFRP.展开更多
Satellited CoNiCrAlY–Al_(2)O_(3)feedstocks with 2wt%, 4wt%, and 6wt% oxide nanoparticles and pure CoNiCrAlY powder were deposited by the high-velocity oxy fuel process on an Inconel738 superalloy substrate. The oxida...Satellited CoNiCrAlY–Al_(2)O_(3)feedstocks with 2wt%, 4wt%, and 6wt% oxide nanoparticles and pure CoNiCrAlY powder were deposited by the high-velocity oxy fuel process on an Inconel738 superalloy substrate. The oxidation test was performed at 1050℃ for 5, 50, 100,150, 200, and 400 h. The microstructure and phase composition of powders and coatings were characterized by scanning electron microscopy and X-ray diffraction, respectively. The bonding strength of the coatings was also evaluated. The results proved that with the increase in the percentage of nanoparticles(from 2wt% to 6wt%), the amount of porosity(from 1vol% to 4.7vol%), unmelted particles, and roughness of the coatings(from 4.8 to 8.8 μm) increased, and the bonding strength decreased from 71 to 48 MPa. The thicknesses of the thermally grown oxide layer of pure and composite coatings(2wt%, 4wt%, and 6wt%) after 400 h oxidation were measured as 6.5, 5.5, 7.6, and 8.1 μm, respectively.The CoNiCrAlY–2wt% Al_(2)O_(3)coating showed the highest oxidation resistance due to the diffusion barrier effect of well-dispersed nanoparticles. The CoNiCrAlY–6wt% Al_(2)O_(3)coating had the lowest oxidation resistance due to its rough surface morphology and porous microstructure.展开更多
Three Ti-6Al-4V alloy powders with median diameters of 103, 66 and 44 pm, respectively, were pressed by high-velocity compaction （HVC） technology and then sintered in vacuum. The effects of particle sizes on forming...Three Ti-6Al-4V alloy powders with median diameters of 103, 66 and 44 pm, respectively, were pressed by high-velocity compaction （HVC） technology and then sintered in vacuum. The effects of particle sizes on forming as well as properties of sintered samples were investigated. The results show that fine powders are more difficult to press than coarse powders and its compact density is lower too. But the sintered density of fine powders is obviously higher than that of coarse powders. Compared with the powders with 103 and 66 ~un in diameter, the green density with 44 ~rn diameter powders is lower, which is 85.1% of theoretical density （TD） at an impact energy of 913 J. After sintering at 1300 ~C for 2,5 h, the sintered density of the compacts with 44 pm diameter powders is the highest, and reaches 98.2% of TD. Moreover, the sintered sample with 44 pan in diameter has the highest hardness and compressive strength, which are HV 354 and 1265 MPa, respectively.展开更多
This paper reviews 19 apparatuses having highvelocity capabilities,describes a rotary-shear low to highvelocity friction apparatus installed at Institute of Geology,China Earthquake Administration,and reports results ...This paper reviews 19 apparatuses having highvelocity capabilities,describes a rotary-shear low to highvelocity friction apparatus installed at Institute of Geology,China Earthquake Administration,and reports results from velocity-jump tests on Pingxi fault gouge to illustrate technical problems in conducting velocity-stepping tests at high velocities.The apparatus is capable of producing plate to seismic velocities（44 mm/a to 2.1 m/s for specimens of 40 mm in diameter）,using a 22 kW servomotor with a gear/belt system having three velocity ranges.A speed range can be changed by 103 or 106by using five electromagnetic clutches without stopping the motor.Two cam clutches allow fivefold velocity steps,and the motor speed can be increased from zero to 1,500 rpm in 0.1-0.2 s by changing the controlling voltage.A unique feature of the apparatus is a large specimen chamber where different specimen assemblies can be installed easily.In addition to a standard specimen assembly for friction experiments,two pressure vessels were made for pore pressures to 70 MPa;one at room temperature and the other at temperatures to 500 °C.Velocity step tests are needed to see if the framework of rate-and-state friction is applicable or not at high velocities.We report results from velocity jump tests from 1.4 mm/s to 1.4 m/s on yellowish gouge from a Pingxi fault zone,located at the northeastern part of the Longmenshan fault system that caused the 2008 Wenchuan earthquake.An instantaneous increase in friction followed by dramatic slip weakening was observed for the yellowish gouge with smooth sliding surfaces of host rock,but no instantaneous response was recognized for the same gouge with roughened sliding surfaces.Instantaneous and transient frictional properties upon velocity steps cannot be separated easily at high velocities,and technical improvements for velocity step tests are suggested.展开更多
High-velocity friction experiments were conducted on clayey fault gouge collected from Hongkou outcrop of Beichuan fault, located at the southwestern part of Longmenshan fault system that caused the disastrous 2008 We...High-velocity friction experiments were conducted on clayey fault gouge collected from Hongkou outcrop of Beichuan fault, located at the southwestern part of Longmenshan fault system that caused the disastrous 2008 Wenchuan earthquake. The ultimate purpose of this study is to reproduce this earthquake by modeling based on measured frictional properties. Dry gouge of about 1 mm in thickness was deformed dry at slip rates of 0.01 to 1.3 m/s and at normal stresses of 0.61 to 3.04 MPa, using a rotary-shear high-velocity frictional testing machine. The gouge displays slip weakening behavior as initial peak friction decays towards steady-state values after a given displacement. Both peak friction and steady-state friction remain high at slow slip rates are exam- ined and gouge only exhibits dramatic weakening at high slip rates, with steady-state friction coefficient values of about 0.1 to 0.2. Specific fracture energy ranges from 1 to 4 MN/m in our results and this is of the same order as seismically determined values. Low friction coefficients measured on experimental faults are in broad agree- ment with lack of thermal anomaly observed from temperature measurements in WFSD-1 drill hole （Wenchuan Earthquake Fault Scientific Drilling Project）, which can be explained by even smaller friction coefficient for the Wenchuan earthquake fault. High-velocity friction experiments with pore water needs to be done to see if even smaller friction is attained or not. Shiny slickenside surfaces form at high slip rates, but not at slow slip rates. Slip zone with slickenside surface changes its color to dark brown and forms duplex-like microstructures, which are similar to those microstructures found in the fault gouges from the Hongkou outcrop. Detailed comparisons between experimentally deformed gouge samples and WFSD drill cores in the future will reveal how much we could reproduce the dynamic weakening processes in operation in fault zones during Wenchuan earthquake at present.展开更多
High-velocity compaction is an advanced compaction technique to obtain high-density compacts at a compaction velocity of ≤10 m/s. It was applied to various metallic powders and was verified to achieve a density great...High-velocity compaction is an advanced compaction technique to obtain high-density compacts at a compaction velocity of ≤10 m/s. It was applied to various metallic powders and was verified to achieve a density greater than 7.5 g/cm^3 for the Fe-based powders. The ability to rapidly and accurately predict the green density of compacts is important, especially as an alternative to costly and time-consuming materials design by trial and error. In this paper, we propose a machine-learning approach based on materials informatics to predict the green density of compacts using relevant material descriptors, including chemical composition, powder properties, and compaction energy. We investigated four models using an experimental dataset for appropriate model selection and found the multilayer perceptron model worked well, providing distinguished prediction performance, with a high correlation coefficient and low error values. Applying this model, we predicted the green density of nine materials on the basis of specific processing parameters. The predicted green density agreed very well with the experimental results for each material, with an inaccuracy less than 2%. The prediction accuracy of the developed method was thus confirmed by comparison with experimental results.展开更多
This paper reports internal structures of a wide fault zone at Shenxigou,Dujiangyan,Sichuan province,China,and high-velocity frictional properties of the fault gouge collected near the coseismic slip zone during the 2...This paper reports internal structures of a wide fault zone at Shenxigou,Dujiangyan,Sichuan province,China,and high-velocity frictional properties of the fault gouge collected near the coseismic slip zone during the 2008 Wenchuan earthquake.Vertical offset and horizontal displacement at the trench site were 2.8 m（NW side up）and 4.8 m（right-lateral）,respectively.The fault zone formed in Triassic sandstone,siltstone,and shale about 500 m away from the Yingxiu-Beichuan fault,a major fault in the Longmenshan fault system.A trench survey across the coseismic fault,and observations of outcrops and drill cores down to a depth of 57 m revealed that the fault zone consists of fault gouge and fault breccia of about0.5 and 250-300 m in widths,respectively,and that the fault strikes N62°E and dips 68° to NW.Quaternary conglomerates were recovered beneath the fault in the drilling,so that the fault moved at least 55 m along the coseismic slip zone,experiencing about 18 events of similar sizes.The fault core is composed of grayish gouge（GG） and blackish gouge（BG） with very complex slip-zone structures.BG contains low-crystalline graphite of about 30 %.High-velocity friction experiments were conducted at normal stresses of 0.6-2.1 MPa and slip rates of 0.1-2.1 m/s.Both GG and BG exhibit dramatic slip weakening at constant high slip rates that can be described as an exponential decay from peak friction coefficient lpto steadystate friction coefficient lssover a slip-weakening distance Dc.Deformation of GG and BG is characterized by overlapped slip-zone structures and development of sharp slickenside surfaces,respectively.Comparison of our data with those reported for other outcrops indicates that the high-velocity frictional properties of the Longmenshan fault zones are quite uniform and the high-velocity weakening must have promoted dynamic rupture propagation during the Wenchuan earthquake.展开更多
In this study, we investigated the changes in the right-to-left shunt (RLS) of the patent foramen ovale (PFO) at different phases of the Valsalva maneuver and analyzed the possible mechanisms. The study population con...In this study, we investigated the changes in the right-to-left shunt (RLS) of the patent foramen ovale (PFO) at different phases of the Valsalva maneuver and analyzed the possible mechanisms. The study population consisted of 57 patients with symptoms highly suggestive of a PFO. These patients had been diagnosed with apsychia, migraine with aura, cerebral infarction, transient ischemic attack (TIA), and cerebral ischemia with unknown cause. Routine echocardiography was performed in all patients to rule out a cardiac malformation. Contrast-transcranial Doppler (c-TCD) and contrast-enhanced transthoracic echocardiography (c-TTE) were used to visualize and quantify the RLS. The standard apical four chamber view was used to observe the changes of E peak, A peak, and velocity-time integral (VTI) ratio of tricuspid blood flow during the strain phase and release phase of the Valsalva maneuver. Paired t-test was used to compare E peak, A peak, and VTI ratio of tricuspid blood flow during the different phases. The right-to-left shunt across the PFO (PFO-RLS) was graded in the two phases and compared by Kruskal-Wallis test. Compared with the strain phase of the Valsalva maneuver, the parameters of E, A, and VTI in diastolic period in patients with PFO-RLS at the release phase were significantly increased [54.30 ± 13.65 cm/s vs 100.35 ± 21.11 cm/s, 42.21 ± 12.32 cm/s vs 57.30 ± 18.88 cm/s, 10.34 ± 3.27 cm/s vs 19.58 ± 4.56 cm/s, respectively], and the difference was statistically significant. The positive consequence of PFO-RLS, as diagnosed by c-TTE with the Valsalva maneuver at the release phase of the Valsalva maneuver, was significantly higher than that at the strain phase of the Valsalva maneuver. At the beginning of release phase of the Valsalva maneuver, decreased intrathoracic pressure led to increased venous backflow into the right atrium. Thus, high-velocity blood flow rapidly pushed the PFO open, which resulted in a significant increase in the PFO-RLS. Therefore, the increase of the PFO-RLS during the Valsalva maneuver is caused by the impact of high-velocity blood flow the PFO.展开更多
Wave equation wave field numerical modeling technology is applied to the observation that deep layer imaging is difficult below a screening layer of high-velocity basalt. Three simple high-velocity basalt models are d...Wave equation wave field numerical modeling technology is applied to the observation that deep layer imaging is difficult below a screening layer of high-velocity basalt. Three simple high-velocity basalt models are designed on the basis of basalt formation characteristics. The analysis of deep-layer reflection seismic signal energy shows that lowfrequency seismic signals are capable of both penetrating the thin high-velocity basalt layer and reducing the diffraction noise caused by the rough surfaces. The simulation experiment of a complete 2D basalt model confirms that the low-frequency signals can be used to boost the quality of deep-layer imaging under the high-velocity basalt layer and achieve good results in low-pass filter processing of actual data.展开更多
The Fe_(949.7)Cr_(18)Mn_(1.9)Mo_(7.4)W_(1.6)B_(15.2)C_(3.8)Si_(2) amorphous coating was deposited on T91 steel substrate by using the high-velocity oxygen fuel(HVOF)spray technique to enhance the corrosion resistance ...The Fe_(949.7)Cr_(18)Mn_(1.9)Mo_(7.4)W_(1.6)B_(15.2)C_(3.8)Si_(2) amorphous coating was deposited on T91 steel substrate by using the high-velocity oxygen fuel(HVOF)spray technique to enhance the corrosion resistance of T91 stainless steel in liquid lead-bismuth eutectic(LBE).The corrosion behavior of the T91 steel and coating exposed to oxygen-saturated LBE at 400℃ for 500 h was investigated.Results showed that the T91 substrate was severely corroded and covered by a homogeneously distributed dual-layer oxide on the interface contacted to LBE,consisting of an outer magnetite layer and an inner Fe-Cr spinel layer.Meanwhile,the amorphous coating with a high glass transition temperature(Tg=550℃)and crystallization temperature(T_(x)=600℃)exhibited dramatically enhanced thermal stability and corrosion resistance.No visible LBE penetration was observed,although small amounts of Fe_(3)O_(4),Cr_(2)O_(3),and PbO were found on the coating surface.In addition,the amorphicity and interface bonding of the coating layer remained unchanged after the LBE corrosion.The Fe-based amorphous coating can act as a stable barrier layer in liquid LBE and have great application potential for long-term service in LBE-cooled fast reactors.展开更多
In the present paper, a three-dimensional （3D） Eulerian technique for the 3D numerical simulation of high-velocity impact problems is proposed. In the Eulerian framework, a complete 3D conservation element and solut...In the present paper, a three-dimensional （3D） Eulerian technique for the 3D numerical simulation of high-velocity impact problems is proposed. In the Eulerian framework, a complete 3D conservation element and solution element scheme for conservative hyperbolic governing equations with source terms is given. A modified ghost fluid method is proposed for the treatment of the boundary conditions. Numerical simulations of the Taylor bar problem and the ricochet phenomenon of a sphere impacting a plate target at an angle of 60~ are carried out. The numerical results are in good agreement with the corresponding experimental observations. It is proved that our computational technique is feasible for analyzing 3D high-velocity impact problems.展开更多
Bird strike studies on typical aluminium leading edges of the Horizontal Tail (HT) with and without Glass Fibre Shape Memory Polymer (GF-SMP) layers are carried out. A one-fifth scaled model of HT is designed and fabr...Bird strike studies on typical aluminium leading edges of the Horizontal Tail (HT) with and without Glass Fibre Shape Memory Polymer (GF-SMP) layers are carried out. A one-fifth scaled model of HT is designed and fabricated. The parameters like bird dimension and energy requirements are accordingly scaled to conduct the bird strike tests. Two leading-edge components have been prepared, namely one with AL 2024-T3 aluminium alloy and the other specimen of the same dimension and material, additionally having GF-SMP composite layers inside the metallic leading edge, in order to enhance its impact resistance. Bird strike experiments are performed on both the specimens, impacting at the centre of the leading edge in the nose tip region with an impact velocity of 115 m/s. The test component is instrumented with linear post-yield strain gauges on the top side and the PZT sensors on the bottom. Furthermore, the impact scenario is monitored using a high-speed camera at 7000 fps. The bird strike event is simulated by an equation of state model, in which the mass of the bird is idealized using smooth particle hydrodynamics element in PAMCRASH<sup>?</sup><sup> </sup>explicit solver. The strain magnitude and its pattern including time duration are found to be in a good correlation between test and simulation. Key metrics are evaluated to devise an SHM scheme for the load and impact event monitoring using strain gauges and PZT sensors. GF-SMP layers have improved the impact resistance of the aluminium leading edge which is certainly encouraging towards finding a novel solution for the high-velocity impact.展开更多
Ballistic impact tests were carried out with examined projectiles of the Ti-6Al-4V titanium alloy to investigate the impact response of the 2618 aluminum plates at a nominal velocity of 210 m/s. The influence of proje...Ballistic impact tests were carried out with examined projectiles of the Ti-6Al-4V titanium alloy to investigate the impact response of the 2618 aluminum plates at a nominal velocity of 210 m/s. The influence of projectile forms and oblique angles on damage formation was particularly discussed by applying different loading conditions such as multiple projectile forms and oblique angles. Additionally, the numerical simulation method was employed to provide further insight into the characteristics of damage and target responses. The Johnson-Cook(J-C)constitutive model with revised failure parameters was used to support the simulations to assess target responses and characteristics of the damage created from different impact conditions. Results show that there is a significant transition in the deformation mode as changes of the projectile form are applied. Moreover, the cracks on the back of the 2618 aluminum alloy plates impacted by the solid plate projectile and the hollow blade projectile tend to locate at different positions, which are supposed to be influenced by local bending and stretching. The work in this paper may provide guidance for the design of fan blade containment systems.展开更多
The wall surface of material is prone to silt abrasion by high-velocity sediment-laden flow. The silt abrasion is different form cavitation erosion. In this article, the characteristics of silt abrasion were discussed...The wall surface of material is prone to silt abrasion by high-velocity sediment-laden flow. The silt abrasion is different form cavitation erosion. In this article, the characteristics of silt abrasion were discussed, The mechanism of silt abrasion was analyzed and the formation and development of ripple shape on wall surface of material were explained thereafter. Based on turbulence theory and test data, some formulas were derived for predicting the abrasion rate of concrete wall surface in high-velocity sediment-laden flow. The calculated results show good agreement with the experimental data.展开更多
Fe-based powder with a composition of Fe_（42.87）Cr_（15.98）Mo_（16.33）C_（15.94）B_（8.88）（at.%）was used to fabricate coatings by high-velocity oxygen fuel spraying.The effects of the spraying parameters on the...Fe-based powder with a composition of Fe_（42.87）Cr_（15.98）Mo_（16.33）C_（15.94）B_（8.88）（at.%）was used to fabricate coatings by high-velocity oxygen fuel spraying.The effects of the spraying parameters on the microstructure and the wear properties of the Fe-based alloy coatings were systematically studied.The results showed that the obtained Fe-based coatings with a thickness of about 400μm consisted of a large-volume amorphous phase and some nanocrystals.With increasing the fuel and oxygen flow rates,the porosity of the obtained coatings decreased.The coating deposited under optimized parameters exhibited the lowest porosity of 2.8%.The excellent wear resistance of this coating was attributed to the properties of the amorphous matrix and the presence of nanocrystals homogeneously distributed within the matrix.The wear mechanism of the coatings was discussed on the basis of observations of the worn surfaces.展开更多
Testing rocket and space technology objects in ground conditions for resistance to the impact of meteoroids and fragments of space debris can be carried out using shaped charges. To substantiate the design parameters ...Testing rocket and space technology objects in ground conditions for resistance to the impact of meteoroids and fragments of space debris can be carried out using shaped charges. To substantiate the design parameters of shaped charges that ensure the formation of aluminum particles in a wide velocity range(from 2.5 to 16 km/s), numerical modeling of the formation process was carried out within the framework of a two-dimensional axisymmetric problem of continuum mechanics using three different computing codes to increase the reliability of the results. The calculations consider shaped charges with a diameter of 20-100 mm with aluminum liners of various shapes. It is shown that the formation of particles with velocities close to the lower limit of the considered range is ensured by gently sloping segmental liners of degressive thickness. To form higher-velocity particles with velocities over 5 km/s, it is proposed to use combined liners, the jet-forming part of which has the shape of a hemisphere of constant thickness or the shape of a semi-ellipsoid or semi-superellipsoid of rotation of degressive thickness.展开更多
This study investigated the hot corrosion performance of a dissimilar weldment of Ni-based superalloy and stainless steel joined by CO2-laser welding and improved by high-velocity oxy-fuel(HVOF)coating in a Na2SO4-60w...This study investigated the hot corrosion performance of a dissimilar weldment of Ni-based superalloy and stainless steel joined by CO2-laser welding and improved by high-velocity oxy-fuel(HVOF)coating in a Na2SO4-60wt%V2O5 environment at 900℃.A dissimilar butt joint of AISI 321 and alloy 825 was fabricated by CO2-laser welding with low heat input after obtaining the optimum welding parameters by bead-on-plate trials.The metallurgical and mechanical properties of the laser weldment were evaluated.The tensile test results indicated the occurrence of fracture in the base metal AISI 321 side.The HVOF process was employed to coat Ni-20wt%Cr on the weldment.To evaluate the surface morphology of the corrosion products formed on the uncoated and Ni-20wt%Cr-coated weldments,scanning electron microscopy(SEM)analysis was performed.Energy-dispersive spectroscopy(EDS)was used to determine the different elements present on the surface scales.The existence of oxide phases on the weldments was determined by X-ray diffraction(XRD).The cross sections of the weldments were characterized by SEM with EDS line mapping analysis.The results indicated that the Ni-20wt%Cr-coated weldment exhibited superior hot corrosion resistance due to the development of Cr2O3 and NiCr2O4 protective oxide scales.展开更多
The marginal sea and back-arc basins in the Western Pacific Ocean have become the focus of tectonics due to their unique tectonic location.To understand the deep crustal structure in the back-arc region,we present a 5...The marginal sea and back-arc basins in the Western Pacific Ocean have become the focus of tectonics due to their unique tectonic location.To understand the deep crustal structure in the back-arc region,we present a 545-kmlong active-source ocean bottom seismometer(OBS)wide-angle reflection/refraction profile in the East China Sea.The P wave velocity model shows that the Moho depth rises significantly,from approximately 30 km in the East China Sea shelf to approximately 16 km in the axis of the Okinawa Trough.The lower crustal high-velocity zone(HVZ)in the southern Okinawa Trough,with V_(p) of 6.8-7.3 km/s,is a remarkable manifestation of the mantle material upwelling and accretion to the lower crust.This confirms that the lower crustal high-velocity mantle accretion is developed in the southern Okinawa Trough.During the process of back-arc extension,the crustal structure of the southern Okinawa Trough is completely invaded and penetrated by the upper mantle material in the axis region.In some areas of the southern central graben,the crust may has broken up and entered the initial stage of seafloor spreading.The discontinuous HVZs in the lower crust in the back-arc region also indicate the migration of spreading centers in the back-arc region since the Cenozoic.The asthenosphere material upwelling in the continent-ocean transition zone is constantly driving the lithosphere eastward for episodic extension,and is causing evident tectonic migration in the Western Pacific back-arc region.展开更多
The present paper deals with the investigation of microstructure and high-temperature hot corrosion behavior of high-velocity oxy fuel(HVOF)-produced coatings. Two powder coating compositions, namely, Ni22Cr10Al1Y all...The present paper deals with the investigation of microstructure and high-temperature hot corrosion behavior of high-velocity oxy fuel(HVOF)-produced coatings. Two powder coating compositions, namely, Ni22Cr10Al1Y alloy powder and Ni22Cr10Al1Y(80 wt%;microsized)–silicon carbide(SiC)(20 wt%;nano(N)) powder, were deposited on a T-22 boiler tube steel. The hot corrosion behavior of bare and coated steels was tested at 900°C for 50 cycles in Na2SO4–60 wt%V2O5 molten-salt environment. The kinetics of corrosion was established with weight change measurements after each cycle. The microporosity and microhardness of the as-coated samples have been reported. The X-ray diffraction,field emission-scanning electron microscopy/energy dispersive spectroscopy, and X-ray mapping characterization techniques have been utilized for structural analysis of the as-coated and hot-corroded samples. The results showed that both coatings were deposited with a porosity less than2%. Both coated samples revealed the development of harder surfaces than the substrate. During hot corrosion testing, the bare T22 steel showed an accelerated corrosion in comparison with its coated counterparts. The HVOF-sprayed coatings were befitted effectively by maintaining their adherence during testing. The Ni22Cr10Al1Y–20 wt%SiC(N) composite coating was more effective than the Ni–22Cr–10Al–1Y coating against corrosion in the high-temperature fluxing process.展开更多
基金supported by the Defense Industrial Technology Development Program(Grant No.JCKY2018604B004)the National Natural Science Foundation of China(Grant No.11972007)。
文摘In this paper,the numerical simulation method is used to study the ballistic performances of hourglass lattice sandwich structures with the same mass under the vertical incidence of fragments.Attention is paid to elucidating the influences of rod cross-section dimensions,structure height,structure layer,and rod inclination angle on the deformation mode,ballistic performances,and ability to change the ballistic direction of fragments.The results show that the ballistic performances of hourglass lattice sandwich structures are mainly affected by their structural parameters.In this respect,structural parameters optimization of the hourglass lattice sandwich structures enable one to effectively improve their ballistic limit velocity and,consequently,ballistic performances.
基金supported by the National Natural Science Foundation of China(Nos.51921003,52275153)the Fundamental Research Funds for the Central Universities(No.NI2023001)+2 种基金the Research Fund of State Key Laboratory of Mechanics and Control for Aero-space Structures(No.MCAS-I-0423G01)the Fund of Pro-spective Layout of Scientific Research for Nanjing University of Aeronautics and Astronauticsthe Priority Academic Program Development of Jiangsu Higher Education Institu-tions of China.
文摘Carbon fiber-reinforced polymer(CFRP)is widely used in aerospace applications.This kind of material may face the threat of high-velocity impact in the process of dedicated service,and the relevant research mainly considers the impact resistance of the material,and lacks the high-velocity impact damage monitoring research of CFRP.To solve this problem,a real high-velocity impact damage experiment and structural health monitoring(SHM)method of CFRP plate based on piezoelectric guided wave is proposed.The results show that CFRP has obvious perforation damage and fiber breakage when high-velocity impact occurs.It is also proved that guided wave SHM technology can be effectively used in the monitoring of such damage,and the damage can be reflected by quantifying the signal changes and damage index(DI).It provides a reference for further research on guided wave structure monitoring of high/hyper-velocity impact damage of CFRP.
文摘Satellited CoNiCrAlY–Al_(2)O_(3)feedstocks with 2wt%, 4wt%, and 6wt% oxide nanoparticles and pure CoNiCrAlY powder were deposited by the high-velocity oxy fuel process on an Inconel738 superalloy substrate. The oxidation test was performed at 1050℃ for 5, 50, 100,150, 200, and 400 h. The microstructure and phase composition of powders and coatings were characterized by scanning electron microscopy and X-ray diffraction, respectively. The bonding strength of the coatings was also evaluated. The results proved that with the increase in the percentage of nanoparticles(from 2wt% to 6wt%), the amount of porosity(from 1vol% to 4.7vol%), unmelted particles, and roughness of the coatings(from 4.8 to 8.8 μm) increased, and the bonding strength decreased from 71 to 48 MPa. The thicknesses of the thermally grown oxide layer of pure and composite coatings(2wt%, 4wt%, and 6wt%) after 400 h oxidation were measured as 6.5, 5.5, 7.6, and 8.1 μm, respectively.The CoNiCrAlY–2wt% Al_(2)O_(3)coating showed the highest oxidation resistance due to the diffusion barrier effect of well-dispersed nanoparticles. The CoNiCrAlY–6wt% Al_(2)O_(3)coating had the lowest oxidation resistance due to its rough surface morphology and porous microstructure.
基金Project (51004040) supported by the National Natural Science Foundation of ChinaProject (20110952K) supported by Open Research Fund of State Key Laboratory of Powder Metallurgy of Central South University, China
文摘Three Ti-6Al-4V alloy powders with median diameters of 103, 66 and 44 pm, respectively, were pressed by high-velocity compaction （HVC） technology and then sintered in vacuum. The effects of particle sizes on forming as well as properties of sintered samples were investigated. The results show that fine powders are more difficult to press than coarse powders and its compact density is lower too. But the sintered density of fine powders is obviously higher than that of coarse powders. Compared with the powders with 103 and 66 ~un in diameter, the green density with 44 ~rn diameter powders is lower, which is 85.1% of theoretical density （TD） at an impact energy of 913 J. After sintering at 1300 ~C for 2,5 h, the sintered density of the compacts with 44 pm diameter powders is the highest, and reaches 98.2% of TD. Moreover, the sintered sample with 44 pan in diameter has the highest hardness and compressive strength, which are HV 354 and 1265 MPa, respectively.
基金supported by State Key Laboratory of Earthquake Dynamics (Project No.LED2014A06 & LED2010A05)
文摘This paper reviews 19 apparatuses having highvelocity capabilities,describes a rotary-shear low to highvelocity friction apparatus installed at Institute of Geology,China Earthquake Administration,and reports results from velocity-jump tests on Pingxi fault gouge to illustrate technical problems in conducting velocity-stepping tests at high velocities.The apparatus is capable of producing plate to seismic velocities（44 mm/a to 2.1 m/s for specimens of 40 mm in diameter）,using a 22 kW servomotor with a gear/belt system having three velocity ranges.A speed range can be changed by 103 or 106by using five electromagnetic clutches without stopping the motor.Two cam clutches allow fivefold velocity steps,and the motor speed can be increased from zero to 1,500 rpm in 0.1-0.2 s by changing the controlling voltage.A unique feature of the apparatus is a large specimen chamber where different specimen assemblies can be installed easily.In addition to a standard specimen assembly for friction experiments,two pressure vessels were made for pore pressures to 70 MPa;one at room temperature and the other at temperatures to 500 °C.Velocity step tests are needed to see if the framework of rate-and-state friction is applicable or not at high velocities.We report results from velocity jump tests from 1.4 mm/s to 1.4 m/s on yellowish gouge from a Pingxi fault zone,located at the northeastern part of the Longmenshan fault system that caused the 2008 Wenchuan earthquake.An instantaneous increase in friction followed by dramatic slip weakening was observed for the yellowish gouge with smooth sliding surfaces of host rock,but no instantaneous response was recognized for the same gouge with roughened sliding surfaces.Instantaneous and transient frictional properties upon velocity steps cannot be separated easily at high velocities,and technical improvements for velocity step tests are suggested.
基金supported by State Key Laboratory of Earthquake Dynamics (project No.LED2008A03)Wenchuan Earthquake Fault Scientific Drilling Project(WFSD),by a Grant-in-Aid for JSPS fellows to the first author (T.Togo) and a Grant-in-Aid for young scientists(B) 201007605,and by a 2009 FGI Grant-in-Aid of Fukada Geological Institute
文摘High-velocity friction experiments were conducted on clayey fault gouge collected from Hongkou outcrop of Beichuan fault, located at the southwestern part of Longmenshan fault system that caused the disastrous 2008 Wenchuan earthquake. The ultimate purpose of this study is to reproduce this earthquake by modeling based on measured frictional properties. Dry gouge of about 1 mm in thickness was deformed dry at slip rates of 0.01 to 1.3 m/s and at normal stresses of 0.61 to 3.04 MPa, using a rotary-shear high-velocity frictional testing machine. The gouge displays slip weakening behavior as initial peak friction decays towards steady-state values after a given displacement. Both peak friction and steady-state friction remain high at slow slip rates are exam- ined and gouge only exhibits dramatic weakening at high slip rates, with steady-state friction coefficient values of about 0.1 to 0.2. Specific fracture energy ranges from 1 to 4 MN/m in our results and this is of the same order as seismically determined values. Low friction coefficients measured on experimental faults are in broad agree- ment with lack of thermal anomaly observed from temperature measurements in WFSD-1 drill hole （Wenchuan Earthquake Fault Scientific Drilling Project）, which can be explained by even smaller friction coefficient for the Wenchuan earthquake fault. High-velocity friction experiments with pore water needs to be done to see if even smaller friction is attained or not. Shiny slickenside surfaces form at high slip rates, but not at slow slip rates. Slip zone with slickenside surface changes its color to dark brown and forms duplex-like microstructures, which are similar to those microstructures found in the fault gouges from the Hongkou outcrop. Detailed comparisons between experimentally deformed gouge samples and WFSD drill cores in the future will reveal how much we could reproduce the dynamic weakening processes in operation in fault zones during Wenchuan earthquake at present.
基金financially supported by the National Key Research and Development Program of China (No. 2016YFB0700503)the National High Technology Research and Development Program of China (No. 2015AA034201)+2 种基金the Beijing Science and Technology Plan (No. D161100002416001)the National Natural Science Foundation of China (No. 51172018)Kennametal Inc
文摘High-velocity compaction is an advanced compaction technique to obtain high-density compacts at a compaction velocity of ≤10 m/s. It was applied to various metallic powders and was verified to achieve a density greater than 7.5 g/cm^3 for the Fe-based powders. The ability to rapidly and accurately predict the green density of compacts is important, especially as an alternative to costly and time-consuming materials design by trial and error. In this paper, we propose a machine-learning approach based on materials informatics to predict the green density of compacts using relevant material descriptors, including chemical composition, powder properties, and compaction energy. We investigated four models using an experimental dataset for appropriate model selection and found the multilayer perceptron model worked well, providing distinguished prediction performance, with a high correlation coefficient and low error values. Applying this model, we predicted the green density of nine materials on the basis of specific processing parameters. The predicted green density agreed very well with the experimental results for each material, with an inaccuracy less than 2%. The prediction accuracy of the developed method was thus confirmed by comparison with experimental results.
基金supported by State Key Laboratory of Earthquake Dynamics (project No.LED2010A03)Wenchuan Earthquake Fault Scientific Drilling Project (WFSD-09)
文摘This paper reports internal structures of a wide fault zone at Shenxigou,Dujiangyan,Sichuan province,China,and high-velocity frictional properties of the fault gouge collected near the coseismic slip zone during the 2008 Wenchuan earthquake.Vertical offset and horizontal displacement at the trench site were 2.8 m（NW side up）and 4.8 m（right-lateral）,respectively.The fault zone formed in Triassic sandstone,siltstone,and shale about 500 m away from the Yingxiu-Beichuan fault,a major fault in the Longmenshan fault system.A trench survey across the coseismic fault,and observations of outcrops and drill cores down to a depth of 57 m revealed that the fault zone consists of fault gouge and fault breccia of about0.5 and 250-300 m in widths,respectively,and that the fault strikes N62°E and dips 68° to NW.Quaternary conglomerates were recovered beneath the fault in the drilling,so that the fault moved at least 55 m along the coseismic slip zone,experiencing about 18 events of similar sizes.The fault core is composed of grayish gouge（GG） and blackish gouge（BG） with very complex slip-zone structures.BG contains low-crystalline graphite of about 30 %.High-velocity friction experiments were conducted at normal stresses of 0.6-2.1 MPa and slip rates of 0.1-2.1 m/s.Both GG and BG exhibit dramatic slip weakening at constant high slip rates that can be described as an exponential decay from peak friction coefficient lpto steadystate friction coefficient lssover a slip-weakening distance Dc.Deformation of GG and BG is characterized by overlapped slip-zone structures and development of sharp slickenside surfaces,respectively.Comparison of our data with those reported for other outcrops indicates that the high-velocity frictional properties of the Longmenshan fault zones are quite uniform and the high-velocity weakening must have promoted dynamic rupture propagation during the Wenchuan earthquake.
文摘In this study, we investigated the changes in the right-to-left shunt (RLS) of the patent foramen ovale (PFO) at different phases of the Valsalva maneuver and analyzed the possible mechanisms. The study population consisted of 57 patients with symptoms highly suggestive of a PFO. These patients had been diagnosed with apsychia, migraine with aura, cerebral infarction, transient ischemic attack (TIA), and cerebral ischemia with unknown cause. Routine echocardiography was performed in all patients to rule out a cardiac malformation. Contrast-transcranial Doppler (c-TCD) and contrast-enhanced transthoracic echocardiography (c-TTE) were used to visualize and quantify the RLS. The standard apical four chamber view was used to observe the changes of E peak, A peak, and velocity-time integral (VTI) ratio of tricuspid blood flow during the strain phase and release phase of the Valsalva maneuver. Paired t-test was used to compare E peak, A peak, and VTI ratio of tricuspid blood flow during the different phases. The right-to-left shunt across the PFO (PFO-RLS) was graded in the two phases and compared by Kruskal-Wallis test. Compared with the strain phase of the Valsalva maneuver, the parameters of E, A, and VTI in diastolic period in patients with PFO-RLS at the release phase were significantly increased [54.30 ± 13.65 cm/s vs 100.35 ± 21.11 cm/s, 42.21 ± 12.32 cm/s vs 57.30 ± 18.88 cm/s, 10.34 ± 3.27 cm/s vs 19.58 ± 4.56 cm/s, respectively], and the difference was statistically significant. The positive consequence of PFO-RLS, as diagnosed by c-TTE with the Valsalva maneuver at the release phase of the Valsalva maneuver, was significantly higher than that at the strain phase of the Valsalva maneuver. At the beginning of release phase of the Valsalva maneuver, decreased intrathoracic pressure led to increased venous backflow into the right atrium. Thus, high-velocity blood flow rapidly pushed the PFO open, which resulted in a significant increase in the PFO-RLS. Therefore, the increase of the PFO-RLS during the Valsalva maneuver is caused by the impact of high-velocity blood flow the PFO.
文摘Wave equation wave field numerical modeling technology is applied to the observation that deep layer imaging is difficult below a screening layer of high-velocity basalt. Three simple high-velocity basalt models are designed on the basis of basalt formation characteristics. The analysis of deep-layer reflection seismic signal energy shows that lowfrequency seismic signals are capable of both penetrating the thin high-velocity basalt layer and reducing the diffraction noise caused by the rough surfaces. The simulation experiment of a complete 2D basalt model confirms that the low-frequency signals can be used to boost the quality of deep-layer imaging under the high-velocity basalt layer and achieve good results in low-pass filter processing of actual data.
基金financially supported by the National Natural Science Foundation of China (Nos. 52061135207, 51871016, 51921001, 5197011039, 5197011018, and U20b200318)the China Nuclear Power Technology Research Institute Co., Ltd
文摘The Fe_(949.7)Cr_(18)Mn_(1.9)Mo_(7.4)W_(1.6)B_(15.2)C_(3.8)Si_(2) amorphous coating was deposited on T91 steel substrate by using the high-velocity oxygen fuel(HVOF)spray technique to enhance the corrosion resistance of T91 stainless steel in liquid lead-bismuth eutectic(LBE).The corrosion behavior of the T91 steel and coating exposed to oxygen-saturated LBE at 400℃ for 500 h was investigated.Results showed that the T91 substrate was severely corroded and covered by a homogeneously distributed dual-layer oxide on the interface contacted to LBE,consisting of an outer magnetite layer and an inner Fe-Cr spinel layer.Meanwhile,the amorphous coating with a high glass transition temperature(Tg=550℃)and crystallization temperature(T_(x)=600℃)exhibited dramatically enhanced thermal stability and corrosion resistance.No visible LBE penetration was observed,although small amounts of Fe_(3)O_(4),Cr_(2)O_(3),and PbO were found on the coating surface.In addition,the amorphicity and interface bonding of the coating layer remained unchanged after the LBE corrosion.The Fe-based amorphous coating can act as a stable barrier layer in liquid LBE and have great application potential for long-term service in LBE-cooled fast reactors.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.10732010,10972010,and 11332002)
文摘In the present paper, a three-dimensional （3D） Eulerian technique for the 3D numerical simulation of high-velocity impact problems is proposed. In the Eulerian framework, a complete 3D conservation element and solution element scheme for conservative hyperbolic governing equations with source terms is given. A modified ghost fluid method is proposed for the treatment of the boundary conditions. Numerical simulations of the Taylor bar problem and the ricochet phenomenon of a sphere impacting a plate target at an angle of 60~ are carried out. The numerical results are in good agreement with the corresponding experimental observations. It is proved that our computational technique is feasible for analyzing 3D high-velocity impact problems.
文摘Bird strike studies on typical aluminium leading edges of the Horizontal Tail (HT) with and without Glass Fibre Shape Memory Polymer (GF-SMP) layers are carried out. A one-fifth scaled model of HT is designed and fabricated. The parameters like bird dimension and energy requirements are accordingly scaled to conduct the bird strike tests. Two leading-edge components have been prepared, namely one with AL 2024-T3 aluminium alloy and the other specimen of the same dimension and material, additionally having GF-SMP composite layers inside the metallic leading edge, in order to enhance its impact resistance. Bird strike experiments are performed on both the specimens, impacting at the centre of the leading edge in the nose tip region with an impact velocity of 115 m/s. The test component is instrumented with linear post-yield strain gauges on the top side and the PZT sensors on the bottom. Furthermore, the impact scenario is monitored using a high-speed camera at 7000 fps. The bird strike event is simulated by an equation of state model, in which the mass of the bird is idealized using smooth particle hydrodynamics element in PAMCRASH<sup>?</sup><sup> </sup>explicit solver. The strain magnitude and its pattern including time duration are found to be in a good correlation between test and simulation. Key metrics are evaluated to devise an SHM scheme for the load and impact event monitoring using strain gauges and PZT sensors. GF-SMP layers have improved the impact resistance of the aluminium leading edge which is certainly encouraging towards finding a novel solution for the high-velocity impact.
基金financial support from the National Natural Science Foundation of China (No. 11772268, 11522220, 11627901 and 11527803)
文摘Ballistic impact tests were carried out with examined projectiles of the Ti-6Al-4V titanium alloy to investigate the impact response of the 2618 aluminum plates at a nominal velocity of 210 m/s. The influence of projectile forms and oblique angles on damage formation was particularly discussed by applying different loading conditions such as multiple projectile forms and oblique angles. Additionally, the numerical simulation method was employed to provide further insight into the characteristics of damage and target responses. The Johnson-Cook(J-C)constitutive model with revised failure parameters was used to support the simulations to assess target responses and characteristics of the damage created from different impact conditions. Results show that there is a significant transition in the deformation mode as changes of the projectile form are applied. Moreover, the cracks on the back of the 2618 aluminum alloy plates impacted by the solid plate projectile and the hollow blade projectile tend to locate at different positions, which are supposed to be influenced by local bending and stretching. The work in this paper may provide guidance for the design of fan blade containment systems.
基金Project supported by the National Natural Science Foundation of China (Grant No: 59279381)
文摘The wall surface of material is prone to silt abrasion by high-velocity sediment-laden flow. The silt abrasion is different form cavitation erosion. In this article, the characteristics of silt abrasion were discussed, The mechanism of silt abrasion was analyzed and the formation and development of ripple shape on wall surface of material were explained thereafter. Based on turbulence theory and test data, some formulas were derived for predicting the abrasion rate of concrete wall surface in high-velocity sediment-laden flow. The calculated results show good agreement with the experimental data.
基金Item Sponsored by National Natural Science Foundation of China(51205001)Key Project of Natural Science of Education Department of Anhui Province of China(KJ2014A023)Scientific Research Starting Foundation of Anhui Polytechnic University of China(2012YQQ006)
文摘Fe-based powder with a composition of Fe_（42.87）Cr_（15.98）Mo_（16.33）C_（15.94）B_（8.88）（at.%）was used to fabricate coatings by high-velocity oxygen fuel spraying.The effects of the spraying parameters on the microstructure and the wear properties of the Fe-based alloy coatings were systematically studied.The results showed that the obtained Fe-based coatings with a thickness of about 400μm consisted of a large-volume amorphous phase and some nanocrystals.With increasing the fuel and oxygen flow rates,the porosity of the obtained coatings decreased.The coating deposited under optimized parameters exhibited the lowest porosity of 2.8%.The excellent wear resistance of this coating was attributed to the properties of the amorphous matrix and the presence of nanocrystals homogeneously distributed within the matrix.The wear mechanism of the coatings was discussed on the basis of observations of the worn surfaces.
文摘Testing rocket and space technology objects in ground conditions for resistance to the impact of meteoroids and fragments of space debris can be carried out using shaped charges. To substantiate the design parameters of shaped charges that ensure the formation of aluminum particles in a wide velocity range(from 2.5 to 16 km/s), numerical modeling of the formation process was carried out within the framework of a two-dimensional axisymmetric problem of continuum mechanics using three different computing codes to increase the reliability of the results. The calculations consider shaped charges with a diameter of 20-100 mm with aluminum liners of various shapes. It is shown that the formation of particles with velocities close to the lower limit of the considered range is ensured by gently sloping segmental liners of degressive thickness. To form higher-velocity particles with velocities over 5 km/s, it is proposed to use combined liners, the jet-forming part of which has the shape of a hemisphere of constant thickness or the shape of a semi-ellipsoid or semi-superellipsoid of rotation of degressive thickness.
文摘This study investigated the hot corrosion performance of a dissimilar weldment of Ni-based superalloy and stainless steel joined by CO2-laser welding and improved by high-velocity oxy-fuel(HVOF)coating in a Na2SO4-60wt%V2O5 environment at 900℃.A dissimilar butt joint of AISI 321 and alloy 825 was fabricated by CO2-laser welding with low heat input after obtaining the optimum welding parameters by bead-on-plate trials.The metallurgical and mechanical properties of the laser weldment were evaluated.The tensile test results indicated the occurrence of fracture in the base metal AISI 321 side.The HVOF process was employed to coat Ni-20wt%Cr on the weldment.To evaluate the surface morphology of the corrosion products formed on the uncoated and Ni-20wt%Cr-coated weldments,scanning electron microscopy(SEM)analysis was performed.Energy-dispersive spectroscopy(EDS)was used to determine the different elements present on the surface scales.The existence of oxide phases on the weldments was determined by X-ray diffraction(XRD).The cross sections of the weldments were characterized by SEM with EDS line mapping analysis.The results indicated that the Ni-20wt%Cr-coated weldment exhibited superior hot corrosion resistance due to the development of Cr2O3 and NiCr2O4 protective oxide scales.
基金supported by the National Key Basic Research Program of China(Grant No.2013CB429701)the National Natural Science Foundation of China(Grant Nos.41606083,91958210,41606050 and 41210005)+1 种基金AoShan Technological Innovation Projects of National Laboratory for Marine Science and Technology(Qingdao)(2015ASKJ03)National Marine Geological Special Project(DD20190236,DD20190365,DD20190377)。
文摘The marginal sea and back-arc basins in the Western Pacific Ocean have become the focus of tectonics due to their unique tectonic location.To understand the deep crustal structure in the back-arc region,we present a 545-kmlong active-source ocean bottom seismometer(OBS)wide-angle reflection/refraction profile in the East China Sea.The P wave velocity model shows that the Moho depth rises significantly,from approximately 30 km in the East China Sea shelf to approximately 16 km in the axis of the Okinawa Trough.The lower crustal high-velocity zone(HVZ)in the southern Okinawa Trough,with V_(p) of 6.8-7.3 km/s,is a remarkable manifestation of the mantle material upwelling and accretion to the lower crust.This confirms that the lower crustal high-velocity mantle accretion is developed in the southern Okinawa Trough.During the process of back-arc extension,the crustal structure of the southern Okinawa Trough is completely invaded and penetrated by the upper mantle material in the axis region.In some areas of the southern central graben,the crust may has broken up and entered the initial stage of seafloor spreading.The discontinuous HVZs in the lower crust in the back-arc region also indicate the migration of spreading centers in the back-arc region since the Cenozoic.The asthenosphere material upwelling in the continent-ocean transition zone is constantly driving the lithosphere eastward for episodic extension,and is causing evident tectonic migration in the Western Pacific back-arc region.
基金DST,New Delhi for their research grant(No.SB/FTP/ETA-435/2012,Dated-10/6/2013)that funded the research and development of the project entitled“Nano-composite Coatings to Control Erosion of Boiler Tubes of Steam Generating Plants.”
文摘The present paper deals with the investigation of microstructure and high-temperature hot corrosion behavior of high-velocity oxy fuel(HVOF)-produced coatings. Two powder coating compositions, namely, Ni22Cr10Al1Y alloy powder and Ni22Cr10Al1Y(80 wt%;microsized)–silicon carbide(SiC)(20 wt%;nano(N)) powder, were deposited on a T-22 boiler tube steel. The hot corrosion behavior of bare and coated steels was tested at 900°C for 50 cycles in Na2SO4–60 wt%V2O5 molten-salt environment. The kinetics of corrosion was established with weight change measurements after each cycle. The microporosity and microhardness of the as-coated samples have been reported. The X-ray diffraction,field emission-scanning electron microscopy/energy dispersive spectroscopy, and X-ray mapping characterization techniques have been utilized for structural analysis of the as-coated and hot-corroded samples. The results showed that both coatings were deposited with a porosity less than2%. Both coated samples revealed the development of harder surfaces than the substrate. During hot corrosion testing, the bare T22 steel showed an accelerated corrosion in comparison with its coated counterparts. The HVOF-sprayed coatings were befitted effectively by maintaining their adherence during testing. The Ni22Cr10Al1Y–20 wt%SiC(N) composite coating was more effective than the Ni–22Cr–10Al–1Y coating against corrosion in the high-temperature fluxing process.
