Hot plane strain compression tests of 6013 aluminum alloy were conducted within the temperature range of 613?773 K and the strain rate range of 0.001?10 s?1. Based on the corrected experimental data with temperature c...Hot plane strain compression tests of 6013 aluminum alloy were conducted within the temperature range of 613?773 K and the strain rate range of 0.001?10 s?1. Based on the corrected experimental data with temperature compensation, Kriging method is selected to model the constitutive relationship among flow stress, temperature, strain rate and strain. The predictability and reliability of the constructed Kriging model are evaluated by statistical measures, comparative analysis and leave-one-out cross-validation (LOO-CV). The accuracy of Kriging model is validated by the R-value of 0.999 and the AARE of 0.478%. Meanwhile, its superiority has been demonstrated while comparing with the improved Arrhenius-type model. Furthermore, the generalization capability of Kriging model is identified by LOO-CV with 25 times of testing. It is indicated that Kriging method is competent to develop accurate model for describing the hot deformation behavior and predicting the flow stress even beyond the experimental conditions in hot compression tests.展开更多
The neutral zinc sulfate solution obtained from hydrometallurgical process of Angouran zinc concentrate has cadmium, nickel and cobalt impurities, that must be purified before electrowinning. Therefore, cadmium and ni...The neutral zinc sulfate solution obtained from hydrometallurgical process of Angouran zinc concentrate has cadmium, nickel and cobalt impurities, that must be purified before electrowinning. Therefore, cadmium and nickel are usually cemented out by addition of zinc dust and remained nickel and cobalt cemented out at second stage with zinc powder and arsenic trioxide. In this research, a new approach is described for determination of effective parameters and optimization of zinc electrolyte hot purification process using statistical design of experiments. The Taguchi method based on orthogonal array design（OAD） has been used to arrange the experimental runs. The experimental conditions involved in the work are as follows： the temperature range of 70-90 ℃ for reaction temperature（T）, 30-90 min for reaction time（t）, 2-4 g/L for zinc powder mass concentration（M）, one to five series for zinc dust particle size distributions（S1-S5）, and 0.1-0.5 g/L（C） for arsenic trioxide mass concentration. Optimum conditions for hot purification obtained in this work are T4（85 ℃）, t4=75 min, M4=3.5 g/L, S4（Serie 4）, and C2=0.2 g/L.展开更多
Thermal conductivity is an important material parameter of silicon when studying the performance and reliability of devices or for guiding circuit design when considering heat dissipation, especially when the self-hea...Thermal conductivity is an important material parameter of silicon when studying the performance and reliability of devices or for guiding circuit design when considering heat dissipation, especially when the self-heating effect becomes prominent in ultra-scaled MOSFETs.The cross-plane thermal conductivity of a thin silicon film is lacking due to the difficulty in sensing high thermal conductivity in the vertical direction.In this paper, a feasible method that utilizes an ultra-fast electrical pulse within 20 μs combined with the hot strip technique is adopted.To the best of our knowledge, this is the first work that shows how to extract the cross-plane thermal conductivity of sub-50 nm(30 nm, 17 nm, and 10 nm)silicon films on buried oxide.The ratio of the extracted cross-plane thermal conductivity of the silicon films over the bulk value is only about 6.9%, 4.3%, and 3.8% at 300 K, respectively.As the thickness of the films is smaller than the phonon mean free path, the classical heat transport theory fails to predict the heat dissipation in nanoscale transistors.Thus, in this study, a ballistic model, derived from the heat transport equation based on extended-irreversible-hydrodynamics(EIT), is used for further investigation, and the simulation results exhibit good consistence with the experimental data.The extracted effective thermal data could provide a good reference for precise device simulations and thermoelectric applications.展开更多
The experimental results of the thermal conductivities of xonotlite-type calcium silicate insulation materials were presented at different temperatures and pressures. Two appropriative surroundings, i.e. an elevated t...The experimental results of the thermal conductivities of xonotlite-type calcium silicate insulation materials were presented at different temperatures and pressures. Two appropriative surroundings, i.e. an elevated temperature surrounding from ambient temperature to 1450 K and a vacuum surrounding from atmosphere pressure to 10-3 Pa, were designed for the transient hot-strip （THS） method. The thermal conductivities of xonotlite-type calcium silicate with four densities from ambient temperature to 1000 K and 0.045 Pa to atmospheric pressure were measured. The results show that the thermal conductivity of xonotlite-type calcium silicate decreases apparently with the fall of density, and decreases apparently with the drop of pressure, and reaches the least value at about 100 Pa. The thermal conductivity of xonotlite-type calcium silicate increases almost linearly with T0, and increases more abundantly with low density than with high density. The thermal conductivity measurement uncertainty is estimated to be approximately 3% at ambient temperature, and 6% at 800 K.展开更多
In this paper a new method for preventing welding hot cracking—the inverse strain method(ISM)is developed on the principle of welding mechan- ics.Effectiveness and feasiblity of method in preventing welding hot crack...In this paper a new method for preventing welding hot cracking—the inverse strain method(ISM)is developed on the principle of welding mechan- ics.Effectiveness and feasiblity of method in preventing welding hot cracking of high strength aluminum alloy LY12CZ by synchronous rolling during welding (SRDW)along both sides of the weld at a suitable distance behind the welding arc are examined.Experimental resulte indicate that welding hot cracking of LY12CY can be effectively prevented and the mechanical properties of welded joint can also be improved by the method.It is an important new solution for preventing hot cracking in welding of sheet metal.展开更多
[Objective] The research aimed to discuss extraction of the chlorophyll a from phytoplankton by hot-ethanol method. [Method] The measurement method of chlorophyll a was improved. By contrast test, the best extraction ...[Objective] The research aimed to discuss extraction of the chlorophyll a from phytoplankton by hot-ethanol method. [Method] The measurement method of chlorophyll a was improved. By contrast test, the best extraction temperature and time of chlorophyll a by hot-ethanol meth- od were studied. Meanwhile, we contrasted hot-ethanol method with specification. I Result] It was simple to use hot-ethanol method to extract chlo- rophyll a from phytoplankton, and it was safe and reliable. When extraction temperature was 75℃ , extraction efficiency of the chlorophyll a was the highest using hot ethanol to hot for 3 min. Chlorophyll a extracted by specification presented significant positive correlation with that by hot-ethanol method. Extraction efficiency of the hot-ethanol method was higher than that of the specification. [ Condusion] The research could provide theoretical reference for extraction of the chlorophyll a from phytoplankton in surface water.展开更多
Based on the conventional uniaxial pre-tensile stress method during welding, this study presents a new method of welding with biaxial pre-stress. With the help of numerical simulation, experiments were carried out on ...Based on the conventional uniaxial pre-tensile stress method during welding, this study presents a new method of welding with biaxial pre-stress. With the help of numerical simulation, experiments were carried out on the self-designed device. Except for the control on residual stress and distortion us-welded, the experimental results also show its effect on the prevention of hot cracks, thus this method can make up for the disadvantage of the conventional pre-stress method. Hot cracks disappear when the value of pre-stress surpasses 0. 2 σs（yield limit）. Welded thin plates with low-level residual stress, little distortion and no hot cracks are obtained with longitudinal pre-tensile stress level between 0. 6σsand 0. 7σs and precompressive stress between 0. 2 σs and 0. 3 σs in transverse direction.展开更多
Test methods for hot abrasion resistance of refractories in China and overseas were briefly introduced. A new test method for hot abrasion resistance was researched. The new method inherits test principle of cold abra...Test methods for hot abrasion resistance of refractories in China and overseas were briefly introduced. A new test method for hot abrasion resistance was researched. The new method inherits test principle of cold abrasion resistance in Chinese standard totally, adopts compressed air pre-heating and electricity heating sam- ples, and is featured with complete structure, good con- trollability, simple operation, and small size. The characteristics and operating procedure of HAT-14A tester were introduced. The hot abrasion resistance of various refractories at different temperatures was tested.展开更多
A new method,the stream surface strip element method,for simulating the three-dimensional deformation of plate and strip rolling process was proposed.The rolling deformation zone was divided into a number of stream su...A new method,the stream surface strip element method,for simulating the three-dimensional deformation of plate and strip rolling process was proposed.The rolling deformation zone was divided into a number of stream surface(curved surface)strip elements along metal flow traces,and the stream surface strip elements were mapped into the corresponding plane strip elements for analysis and computation.The longitudinal distributions of the lateral displacement and the altitudinal displacement of metal were respectively constructed to be a quartic curve and a quadratic curve,of which the lateral distributions were expressed as the third-power spline function,and the altitudinal distributions were fitted in the quadratic curve.From the flow theory of plastic mechanics,the mathematical models of the three-dimensional deformations and stresses of the deformation zone were constructed.Compared with the streamline strip element method proposed by the first author of this paper,the stream surface strip element method takes into account the uneven distributions of stresses and deformations along altitudinal direction,and realizes the precise three-dimensional analysis and computation.The simulation example of continuous hot rolled strip indicates that the method and the model accord with facts and provide a new reliable engineering-computation method for the three-dimensional mechanics simulation of plate and strip rolling process.展开更多
To develop the green polymeric membrane electrolyte,-Polycaprolactone(PCL)was used as a host and the Ionic liquid(IL)(1-Ethyl-3-methylimidazolium tosylate)as a dopant.The IL is a source of mobile charges in the polyme...To develop the green polymeric membrane electrolyte,-Polycaprolactone(PCL)was used as a host and the Ionic liquid(IL)(1-Ethyl-3-methylimidazolium tosylate)as a dopant.The IL is a source of mobile charges in the polymer electrolyte system.The composite membrane has been prepared by Hot Press method and then we characterised this membrane for ionic transportation.Formation of nanocomposite system has been ascertained from their XRD pattern.Interaction phenomenon was studied by ATR based FTIR and Laser Raman spectroscopic technique.Variation of conductivity with composition and temperature was studied with the aid of impedance spectroscopy data.展开更多
This paper proposes a voltage-based hot-spot detection method for defective cells in PV module using projector. The presence of internal crystal defects is one of the main causes of hot-spot phenomenon in PV modules. ...This paper proposes a voltage-based hot-spot detection method for defective cells in PV module using projector. The presence of internal crystal defects is one of the main causes of hot-spot phenomenon in PV modules. Authors previously investigated the physical characteristics of hot-spot phenomenon referring to internal crystal defect. Based on it, a hot-spot detection method named as current-based SRC （self reverse current） detection method is developed. However, it becomes extraordinarily complicated to determine the defective cells under low illumination. In order to avoid this disadvantage, authors improve the SRC detection method by applying voltage. From the feasibility experiment results, it is confirmed that by calculating cell HSI （hotspots index） with voltage, the PV modules with defective cells can be prospectively excluded even under low illumination.展开更多
Hot spinning process has attracted significant attention because it can be used to manufacture complex parts, extend the forming limit of materials, decrease forming forces and reduce process chains. In this paper, we...Hot spinning process has attracted significant attention because it can be used to manufacture complex parts, extend the forming limit of materials, decrease forming forces and reduce process chains. In this paper, we review researches on lightweight metals spun at elevated temperatures since they are difficult to deform at room temperature. These metals include light alloys, such as titanium, magnesium and aluminum alloys, and metal composites. Then, the heating methods used in the hot spinning process and the treatment methods employed for the temperature boundary condition in finite element analyses for the process were discussed. Finally, the future development directions for the hot spinning process of lightweight but difficult-to-deform alloys were highlighted.展开更多
基金Project(51475156)supported by the National Natural Science Foundation of ChinaProject(2014ZX04002071)supported by the National Key Project of Science and Technology of ChinaProject(GXKFJ14-08)supported by the Opening Foundation of Key Laboratory for Non-Ferrous Metal and Featured Material Processing,Guangxi Zhuang Autonomous Region,China
文摘Hot plane strain compression tests of 6013 aluminum alloy were conducted within the temperature range of 613?773 K and the strain rate range of 0.001?10 s?1. Based on the corrected experimental data with temperature compensation, Kriging method is selected to model the constitutive relationship among flow stress, temperature, strain rate and strain. The predictability and reliability of the constructed Kriging model are evaluated by statistical measures, comparative analysis and leave-one-out cross-validation (LOO-CV). The accuracy of Kriging model is validated by the R-value of 0.999 and the AARE of 0.478%. Meanwhile, its superiority has been demonstrated while comparing with the improved Arrhenius-type model. Furthermore, the generalization capability of Kriging model is identified by LOO-CV with 25 times of testing. It is indicated that Kriging method is competent to develop accurate model for describing the hot deformation behavior and predicting the flow stress even beyond the experimental conditions in hot compression tests.
文摘The neutral zinc sulfate solution obtained from hydrometallurgical process of Angouran zinc concentrate has cadmium, nickel and cobalt impurities, that must be purified before electrowinning. Therefore, cadmium and nickel are usually cemented out by addition of zinc dust and remained nickel and cobalt cemented out at second stage with zinc powder and arsenic trioxide. In this research, a new approach is described for determination of effective parameters and optimization of zinc electrolyte hot purification process using statistical design of experiments. The Taguchi method based on orthogonal array design（OAD） has been used to arrange the experimental runs. The experimental conditions involved in the work are as follows： the temperature range of 70-90 ℃ for reaction temperature（T）, 30-90 min for reaction time（t）, 2-4 g/L for zinc powder mass concentration（M）, one to five series for zinc dust particle size distributions（S1-S5）, and 0.1-0.5 g/L（C） for arsenic trioxide mass concentration. Optimum conditions for hot purification obtained in this work are T4（85 ℃）, t4=75 min, M4=3.5 g/L, S4（Serie 4）, and C2=0.2 g/L.
基金Project supported by the Zhejiang Provincial Natural Science Foundation of China(Grant No.LZ19F040001)the National Natural Science Foundation of China(Grant No.61473287)the NSFC–Zhejiang Joint Fund for the Integration of Industrialization Informatization,China(Grant No.U1609213)
文摘Thermal conductivity is an important material parameter of silicon when studying the performance and reliability of devices or for guiding circuit design when considering heat dissipation, especially when the self-heating effect becomes prominent in ultra-scaled MOSFETs.The cross-plane thermal conductivity of a thin silicon film is lacking due to the difficulty in sensing high thermal conductivity in the vertical direction.In this paper, a feasible method that utilizes an ultra-fast electrical pulse within 20 μs combined with the hot strip technique is adopted.To the best of our knowledge, this is the first work that shows how to extract the cross-plane thermal conductivity of sub-50 nm(30 nm, 17 nm, and 10 nm)silicon films on buried oxide.The ratio of the extracted cross-plane thermal conductivity of the silicon films over the bulk value is only about 6.9%, 4.3%, and 3.8% at 300 K, respectively.As the thickness of the films is smaller than the phonon mean free path, the classical heat transport theory fails to predict the heat dissipation in nanoscale transistors.Thus, in this study, a ballistic model, derived from the heat transport equation based on extended-irreversible-hydrodynamics(EIT), is used for further investigation, and the simulation results exhibit good consistence with the experimental data.The extracted effective thermal data could provide a good reference for precise device simulations and thermoelectric applications.
基金supported by the National Natural Science Foundation of China (No.50806021)
文摘The experimental results of the thermal conductivities of xonotlite-type calcium silicate insulation materials were presented at different temperatures and pressures. Two appropriative surroundings, i.e. an elevated temperature surrounding from ambient temperature to 1450 K and a vacuum surrounding from atmosphere pressure to 10-3 Pa, were designed for the transient hot-strip （THS） method. The thermal conductivities of xonotlite-type calcium silicate with four densities from ambient temperature to 1000 K and 0.045 Pa to atmospheric pressure were measured. The results show that the thermal conductivity of xonotlite-type calcium silicate decreases apparently with the fall of density, and decreases apparently with the drop of pressure, and reaches the least value at about 100 Pa. The thermal conductivity of xonotlite-type calcium silicate increases almost linearly with T0, and increases more abundantly with low density than with high density. The thermal conductivity measurement uncertainty is estimated to be approximately 3% at ambient temperature, and 6% at 800 K.
文摘In this paper a new method for preventing welding hot cracking—the inverse strain method(ISM)is developed on the principle of welding mechan- ics.Effectiveness and feasiblity of method in preventing welding hot cracking of high strength aluminum alloy LY12CZ by synchronous rolling during welding (SRDW)along both sides of the weld at a suitable distance behind the welding arc are examined.Experimental resulte indicate that welding hot cracking of LY12CY can be effectively prevented and the mechanical properties of welded joint can also be improved by the method.It is an important new solution for preventing hot cracking in welding of sheet metal.
文摘[Objective] The research aimed to discuss extraction of the chlorophyll a from phytoplankton by hot-ethanol method. [Method] The measurement method of chlorophyll a was improved. By contrast test, the best extraction temperature and time of chlorophyll a by hot-ethanol meth- od were studied. Meanwhile, we contrasted hot-ethanol method with specification. I Result] It was simple to use hot-ethanol method to extract chlo- rophyll a from phytoplankton, and it was safe and reliable. When extraction temperature was 75℃ , extraction efficiency of the chlorophyll a was the highest using hot ethanol to hot for 3 min. Chlorophyll a extracted by specification presented significant positive correlation with that by hot-ethanol method. Extraction efficiency of the hot-ethanol method was higher than that of the specification. [ Condusion] The research could provide theoretical reference for extraction of the chlorophyll a from phytoplankton in surface water.
文摘Based on the conventional uniaxial pre-tensile stress method during welding, this study presents a new method of welding with biaxial pre-stress. With the help of numerical simulation, experiments were carried out on the self-designed device. Except for the control on residual stress and distortion us-welded, the experimental results also show its effect on the prevention of hot cracks, thus this method can make up for the disadvantage of the conventional pre-stress method. Hot cracks disappear when the value of pre-stress surpasses 0. 2 σs（yield limit）. Welded thin plates with low-level residual stress, little distortion and no hot cracks are obtained with longitudinal pre-tensile stress level between 0. 6σsand 0. 7σs and precompressive stress between 0. 2 σs and 0. 3 σs in transverse direction.
文摘Test methods for hot abrasion resistance of refractories in China and overseas were briefly introduced. A new test method for hot abrasion resistance was researched. The new method inherits test principle of cold abrasion resistance in Chinese standard totally, adopts compressed air pre-heating and electricity heating sam- ples, and is featured with complete structure, good con- trollability, simple operation, and small size. The characteristics and operating procedure of HAT-14A tester were introduced. The hot abrasion resistance of various refractories at different temperatures was tested.
基金Sponsored by National Natural Science Foundation of China(50175095)Provincial Natural Science Foundation of Hebei of China(502173)
文摘A new method,the stream surface strip element method,for simulating the three-dimensional deformation of plate and strip rolling process was proposed.The rolling deformation zone was divided into a number of stream surface(curved surface)strip elements along metal flow traces,and the stream surface strip elements were mapped into the corresponding plane strip elements for analysis and computation.The longitudinal distributions of the lateral displacement and the altitudinal displacement of metal were respectively constructed to be a quartic curve and a quadratic curve,of which the lateral distributions were expressed as the third-power spline function,and the altitudinal distributions were fitted in the quadratic curve.From the flow theory of plastic mechanics,the mathematical models of the three-dimensional deformations and stresses of the deformation zone were constructed.Compared with the streamline strip element method proposed by the first author of this paper,the stream surface strip element method takes into account the uneven distributions of stresses and deformations along altitudinal direction,and realizes the precise three-dimensional analysis and computation.The simulation example of continuous hot rolled strip indicates that the method and the model accord with facts and provide a new reliable engineering-computation method for the three-dimensional mechanics simulation of plate and strip rolling process.
文摘To develop the green polymeric membrane electrolyte,-Polycaprolactone(PCL)was used as a host and the Ionic liquid(IL)(1-Ethyl-3-methylimidazolium tosylate)as a dopant.The IL is a source of mobile charges in the polymer electrolyte system.The composite membrane has been prepared by Hot Press method and then we characterised this membrane for ionic transportation.Formation of nanocomposite system has been ascertained from their XRD pattern.Interaction phenomenon was studied by ATR based FTIR and Laser Raman spectroscopic technique.Variation of conductivity with composition and temperature was studied with the aid of impedance spectroscopy data.
文摘This paper proposes a voltage-based hot-spot detection method for defective cells in PV module using projector. The presence of internal crystal defects is one of the main causes of hot-spot phenomenon in PV modules. Authors previously investigated the physical characteristics of hot-spot phenomenon referring to internal crystal defect. Based on it, a hot-spot detection method named as current-based SRC （self reverse current） detection method is developed. However, it becomes extraordinarily complicated to determine the defective cells under low illumination. In order to avoid this disadvantage, authors improve the SRC detection method by applying voltage. From the feasibility experiment results, it is confirmed that by calculating cell HSI （hotspots index） with voltage, the PV modules with defective cells can be prospectively excluded even under low illumination.
基金Project(51222509) supported by the National Science Fund for Excellent Young Scholars of ChinaProject(51175429) supported by the National Natural Science Foundation of ChinaProjects(97-QZ-2014,90-QP-2013) supported by the Research Fund of the State Key Laboratory of Solidification Processing(NWPU) of China
文摘Hot spinning process has attracted significant attention because it can be used to manufacture complex parts, extend the forming limit of materials, decrease forming forces and reduce process chains. In this paper, we review researches on lightweight metals spun at elevated temperatures since they are difficult to deform at room temperature. These metals include light alloys, such as titanium, magnesium and aluminum alloys, and metal composites. Then, the heating methods used in the hot spinning process and the treatment methods employed for the temperature boundary condition in finite element analyses for the process were discussed. Finally, the future development directions for the hot spinning process of lightweight but difficult-to-deform alloys were highlighted.
