Corrosion leakages often occur in the air cooler of a hydrocracking unit,with the failure sites mainly located in the entrance area of the tubes.An analysis of the macroscopic morphology and corrosion products confirm...Corrosion leakages often occur in the air cooler of a hydrocracking unit,with the failure sites mainly located in the entrance area of the tubes.An analysis of the macroscopic morphology and corrosion products confirmed that the damage was caused by erosion-corrosion(E-C).Numerical and experimental methods were applied to investigate the E-C mechanism in the air cooler.Computational fluid dynamics(CFD)was used to calculate the hydrodynamic parameters of the air cooler.The results showed that there was a biased flow in the air cooler,which led to a significant increase in velocity,turbulent kinetic energy and wall shear within 0.2 m of the tube entrance.A visualization experiment was then performed to determine the principles of migration and transformation of multiphase flow in the air cooler tubes.Various flow patterns(pure droplet flow,mist flow,and annular flow)and their evolutionary processes were clearly depicted experimentally.The initiation mechanism and processes leading to the development of E-C in the air cooler were also determined.This study provided a comprehensive explanation for the E-C failures that occur in air coolers during operation.展开更多
Hydroconversion of coal tar to produce aromatic hydrocarbons(BTX)represents a crucial strategy for the highvalue hierarchical utilization of coal.This study focused on the hydrocracking of hydrorefined products derive...Hydroconversion of coal tar to produce aromatic hydrocarbons(BTX)represents a crucial strategy for the highvalue hierarchical utilization of coal.This study focused on the hydrocracking of hydrorefined products derived from coal tar to enhance the production of benzene,toluene,and xylene(BTX).Various reaction conditions,including reaction temperature,hydrogen pressure,space velocity,and hydrogen-to-oil volume ratio,were systematically explored to optimize BTX yields while also considering the process’s economic feasibility.The results indicate that increasing the reaction temperature from 360℃ to 390℃ significantly favors the production of BTX,with yields increasing from 21.42%to 41.14%.Similarly,an increase in hydrogen pressure from 4 MPa to 6 MPa boosts BTX production,with yields rising from 36.31%to 41.14%.Reducing the space velocity from 2 h^(-1) to 0.5 h^(-1) also favors the BTX production process,with yields increasing from 37.96%to 45.13%.Furthermore,raising the hydrogen-to-oil volume ratio from 750 to 1500 improves BTX yields from 41.61%to 45.44%.Through economic analysis,the optimal conditions for BTX production were identified as a reaction temperature of 390℃,hydrogen pressure of 5-6 MPa,space velocity of 1 h^(-1),and hydrogen-to-oil volume ratio of 1000,achieving a BTX yield of 43.73%.This investigation highlights the importance of a holistic evaluation of hydrocracking conditions to optimize BTX production.Furthermore,the findings offer valuable insights for the design and operation of industrial hydrocracking processes aimed at efficiently converting coal tar-derived hydrorefined feedstock into BTX.展开更多
This paper reports the application of multi-component hydrocracking catalyst grading technology in diesel hydrocracking system to increase naphtha,and studies the influence of catalyst systems with different number of...This paper reports the application of multi-component hydrocracking catalyst grading technology in diesel hydrocracking system to increase naphtha,and studies the influence of catalyst systems with different number of graded beds on the reaction process of diesel hydrocracking.Three hydrocracking catalysts with different physicochemical properties as gradation components,the diesel hydrocracking reaction on catalyst systems of one-component,two-component and three-component graded beds with different loading sequences are carried out and evaluated,respectively.The catalytic mechanism of the multi-component grading system is analyzed.The results show that,with the increase of the number of grading beds,the space velocity of reaction on each catalyst increases,which can effectively control the overreaction process;along the flow direction of feedstock,the loading sequences of catalysts with acidity decreasing and pore properties increasing can satisfy the demand of different catalytic activity for the conversion of reactant with changing composition to naphtha,which has a guiding role in the conversion of feedstock to target products.Therefore,the conversion of diesel,the selectivity and yield of naphtha all increase significantly on the multi-component catalyst system.The research on the grading technology of multi-component catalysts is of great significance to the promotion and application of catalyst systems in various catalytic fields.展开更多
To deeply understand the effects of support properties on the performance of Mo-based slurry-phase hydrocracking catalysts,four Mo-based catalysts supported on amorphous silica alumina(ASA),γ-Al_(2)O_(3),ultra-stable...To deeply understand the effects of support properties on the performance of Mo-based slurry-phase hydrocracking catalysts,four Mo-based catalysts supported on amorphous silica alumina(ASA),γ-Al_(2)O_(3),ultra-stable Y(USY)zeolite and SiO_(2) were prepared by the incipient wetness impregnation method,respectively,and their catalytic performances were compared in the vacuum residue(VR)hydrocracking process.It is found that the Mo/ASA catalyst exhibits the highest VR conversion among the different catalysts,indicating that both the appropriate amount of acid sites,especially B acid sites and larger mesoporous volume of ASA can enhance the VR hydrocracking into light distillates.Furthermore,Mo catalysts supported on the different supports show quite different product distributions in VR hydrocracking.The Mo/ASA catalyst provides higher yields of naphtha and middle distillates and lower yields of gas and coke compared with other catalysts,it is attributed to the highest MoS_(2) slab dispersion,the highest sulfuration degree of Mo species,and the most Mo atoms located at the edge sites for the Mo/ASA catalyst,as observed by HRTEM and XPS analyses.These features of Mo/ASA are beneficial for the hydrogenation of intermediate products and polycyclic aromatic hydrocarbons to restrict the gas and coke formation.展开更多
A series of functionalized USY/SiO_(2) zeolite composite supports were synthesized using the coating coprecipitation method,with tetraethyl orthosilicate(TEOS)as the silicon source and different ratios of USY to TEOS....A series of functionalized USY/SiO_(2) zeolite composite supports were synthesized using the coating coprecipitation method,with tetraethyl orthosilicate(TEOS)as the silicon source and different ratios of USY to TEOS.Active metals nickel(Ni)and molybdenum(Mo)were loaded onto the supports using the impregnation method.Finally,a series of hydrogenation catalysts were synthesized.The characterization results showed that,compared with the USY catalyst,the addition of a certain quantity of SiO_(2) resulted in the disappearance of the strong acid sites on the catalyst,the number of weak acid and medium strong acid sites decreased,and a certain number of secondary mesoporous structures were formed.The addition of SiO_(2) reduced the secondary cracking of benzene,toluene,xylene,and ethylbenzene(BTXE)effectively,while excessive amounts of SiO_(2) reduced the hydrogenation activity of the catalyst,leading to a decline in the final yield of BTXE.At a maximum SiO_(2) content of 45%,the hydrogenation depth of light cycle oil(LCO)reached an optimum value.The hydrogenation performance of LCO was investigated in a fixed bed reactor at 380℃,4 MPa,and H2/oil volume ratio of 800:1,where the gasoline and diesel fractions reached 80.00%and 16.74%,respectively.NiMo-YS45 had the highest BTXE selectivity,and the final yield of BTXE reached 21.27%.展开更多
The upgrading of diesel oil to produce ethylene rich cracking feedstock is an important and promising technical route to reduce the ratio of diesel to gasoline. In the present work, a hydrocracking catalyst suitable f...The upgrading of diesel oil to produce ethylene rich cracking feedstock is an important and promising technical route to reduce the ratio of diesel to gasoline. In the present work, a hydrocracking catalyst suitable for selective hydrocracking of straight run diesel oil to produce high-quality ethylene cracking feedstock at low cost was developed, by optimizing the composition of catalyst support materials, using amorphous silicon aluminum and aluminum oxide with high mesopore content as the main support, and modified Y zeolite with excellent aromatic ring opening selectivity as the acidic component. The catalyst has in-depth characterized by X-ray diffraction, transmission electron microscopy, scanning electron microscopy, N<sub>2</sub>-low temperature adsorption-desorption, NH<sub>3</sub>-temperature-programmed desorption, and IR techniques. And its catalytic cracking straight run diesel oil performance was evaluated. The results show that the prepared catalyst has high polycyclic aromatic hydrocarbon ring opening cracking selectivity. However, alkanes retained in diesel distillates can achieve the goal of producing more ethylene cracking feedstocks with low BMCI value under low and moderate pressure conditions. This work may shed significant technical insight for oil refining transformation.展开更多
Nobel metallic Pt/ZSM-22 and Pt/ZSM-23 catalysts were prepared for hydroisomerization of normal dodecane and hydrodewaxing of heavy waxy lube base oil.The hydroisomerization performance of n-dodecane indicated that th...Nobel metallic Pt/ZSM-22 and Pt/ZSM-23 catalysts were prepared for hydroisomerization of normal dodecane and hydrodewaxing of heavy waxy lube base oil.The hydroisomerization performance of n-dodecane indicated that the Pt/ZSM-23 catalyst preferred to crack the C-C bond near the middle of n-dodecane chain,while the Pt/ZSM-22 catalyst was favorable for breaking the carbon chain near the end of n-dodecane.As a result,more than 2%of light products(gas plus naphtha)and3%more of heavy lube base oil with low-pour point and high viscosity index were produced on Pt/ZSM-22 than those on Pt/ZSM-23 while using the heavy waxy vacuum distillate oil as feedstock.展开更多
Light cycle oil(LCO) with high content of poly-aromatics was difficult to upgrade and convert,which had hindered upgrading fuel quality to meet with the standard of automotive diesel for the purpose of sustainable dev...Light cycle oil(LCO) with high content of poly-aromatics was difficult to upgrade and convert,which had hindered upgrading fuel quality to meet with the standard of automotive diesel for the purpose of sustainable development.The hydrocracking behaviors of typical aromatics in LCO of naphthalene and tetralin were investigated over NiMo and CoMo catalysts.Several characterization methods including N2-adsoprtion and desorption,ammonia temperature-programmed desorption(NH3-TPD),Pyridine infrared spectroscopy(Py-IR),CO infrared spectroscopy(CO-IR),Raman and X-ray photoelectron spectroscopy(XPS) were applied to determine the properties of different catalysts.The results showed that CoMo catalyst with high concentration of S-edges could hydrosaturate more naphthalene to tetralin but exhibit lower yield of high-value light aromatics(carbon numbers less than 10) than NiMo catalyst.NiMo catalyst with high concentration of Mo-edges also presented a higher selectivity of converting naphthalene into cyclanes than CoMo catalyst.Subsequently,the naphthalene and LCO hydrocracking performances were also investigated over different catalysts systems.The activity evaluation and kinetic analysis results showed that the naphthalene hydrocracking conversion and the yield of light aromatics for CoMo-AY/NiMo-AY grading catalysts were higher than NiMo-AY/CoMo-AY grading catalysts at same condition.A stepwise reaction principle was proposed to explain the high efficiency of CoMo-AY/NiMoAY grading catalysts.Finally,the LCO hydrocracking evaluation results confirmed that CoMo-AY/NiMoAY catalysts grading system with low carbon deposition and high stability could remain high percentage of active phases,which was more efficient to convert LCO to high-octane gasoline.展开更多
In this work,NiMo catalysts with various contents of MoO_(3)were prepared through incipient wetness impregnation by a twostep method(NMxA)and onepot method(NMxB).The catalysts were then characterized by XRD,XPS,NH3TPD...In this work,NiMo catalysts with various contents of MoO_(3)were prepared through incipient wetness impregnation by a twostep method(NMxA)and onepot method(NMxB).The catalysts were then characterized by XRD,XPS,NH3TPD,H_(2)TPR,HRTEM,and N_(2)adsorptiondesorption technologies.The performance of the NiMo/Al_(2)O_(3) catalysts was investigated by hydrocracking lowtemperature coal tar.When the MoO3 content was 15 wt%,the interaction between Ni species and Al_(2)O_(3) on the NM15B catalyst was stronger than that on the NM15A catalyst,resulting in the poor performance of the former.When the MoO^(3) content was 20 wt%,MoO_(3) agglomerated on the surface of the NM20A catalyst,leading to decreased number of active sites and specific surface area and reduced catalytic performance.The increase in the number of MoS_(2) stack layers strengthened the interaction between Ni and Mo species of the NM20B catalyst and consequently improved its catalytic performance.When the MoO_(3) content reached 25 wt%,the active metals agglomerated on the surface of the NiMo catalysts,thereby directly decreasing the number of active sites.In conclusion,the twostep method is suitable for preparing catalysts with large pore diameter and low MoO_(3) content loading,and the onepot method is more appropriate for preparing catalysts with large specific surface area and high MoO_(3) content.Moreover,the NMxA catalysts had larger average pore diameter than the NMxB catalysts and exhibited improved desulfurization performance.展开更多
One of the commercial means to convert heavy oil residue is hydrocracking in an ebullated bed. The ebullated bed reactor includes a complex gas–liquid–solid backmixed system which attracts the attention of many scie...One of the commercial means to convert heavy oil residue is hydrocracking in an ebullated bed. The ebullated bed reactor includes a complex gas–liquid–solid backmixed system which attracts the attention of many scientists and research groups. This work is aimed at the calculation of the internal recycle flow rate and understanding its effect on other parameters of the ebullated bed. Measured data were collected from an industrial scale residual hydrocracking unit consisting of a cascade of three ebullated bed reactors. A simplified block model of the ebullated bed reactors was created in Aspen Plus and fed with measured data. For reaction yield calculation, a lumped kinetic model was used. The model was verified by comparing experimental and calculated distillation curves as well as the calculated and measured reactor inlet temperature. Influence of the feed rate on the recycle ratio(recycle to feed flow rate) was estimated. A relation between the recycle flow rate, pump pressure difference and catalyst inventory has been identified. The recycle ratio also affects the temperature gradient along the reactor cascade. Influence of the recycle ratio on the temperature gradient decreased with the cascade member order.展开更多
In this study,selective dealumination of Beta zeolites was performed through partially removing the templating agent in Beta zeolites by calcination and then removing the aluminum on the external surface of Beta zeoli...In this study,selective dealumination of Beta zeolites was performed through partially removing the templating agent in Beta zeolites by calcination and then removing the aluminum on the external surface of Beta zeolites with acid treatment.Hydrocracking catalysts were prepared by loading WO_(3)onto these dealuminated Beta zeolites.It was shown that the surface SiO_(2)/Al_(2)O_(3)of selectively dealuminated Beta zeolites was higher than that of conventionally dealuminated samples for the same bulk SiO_(2)/Al_(2)O_(3),and the hydrogenation activity of the catalyst of the selectively dealuminated Beta zeolites was lower than that of conventionally dealuminated Beta zeolites.The experimental results for tetralin hydrocracking to BTX showed that the catalysts based on the selectively dealuminated Beta zeolites had higher BTX selectivity and lower coke formation rate than that the catalysts based on the conventionally dealuminated Beta zeolites.展开更多
Conversion of LCO(light cycle oil)to BTX(benzene,toluene,and xylene)is an economically valuable method for refineries.However,this approach still faces difficulties as the main reactions are not clearly understood.Her...Conversion of LCO(light cycle oil)to BTX(benzene,toluene,and xylene)is an economically valuable method for refineries.However,this approach still faces difficulties as the main reactions are not clearly understood.Here we study the detailed hydrocracking pathway of typical reactants,1-methylnaphthalene and tetralin,through molecular simulations and experiments to improve our understanding of the conversion process of LCO to BTX.Molecular simulations demonstrate that the rate-determining step is the isomerization pathway of six-membered ring to five-membered ring in tetralin as its activation energy(ΔEa)is the highest among all the reactions and the order ofΔEa of reactions is isomerization>ring-opening≈side-chain cleavage.The results of experiments show that with the increase in reaction depth,i.e.,through a high temperature(350-370℃)and low LHSV(4.5-6.0 h^(−1)),isomerization,ring-opening,and side-chain cleavage reactions occurred,thus improving the selectivity and yield of alkyl aromatics.展开更多
Three different zeolite catalysts with different pore sizes(MFI-type,BEA-type,and FAU-type zeolites)have been prepared.The influence of different zeolite catalysts on reactivity and product shape selectivity of tetral...Three different zeolite catalysts with different pore sizes(MFI-type,BEA-type,and FAU-type zeolites)have been prepared.The influence of different zeolite catalysts on reactivity and product shape selectivity of tetralin is investigated.Clear differences are observed in the reactivity of tetralin and distribution of products achieved by different catalysts.The diffusion and adsorption behavior of the reactant tetralin and its intermediates,n-butylbenzene and 1-methylindane under the reaction conditions are simulated using molecular simulation methods.Upon combining simulation results and experimental observations,it is shown that the difference in diffusion coefficient and competitive adsorption capacity can explain the reactivity of tetralin and the selectivity of products.The steric hindrance of the MFI-type zeolite mainly limits the key step of ring opening of tetralin,leading to lower selectivity of ring-opening products.n-Butylbenzene molecules can diffuse sufficiently fast in the large pores of FAU-type zeolite and the weak adsorption capacity of n-butylbenzene leads to its insufficient cracking.In addition,it also explains the reason that the BEA-type zeolite has the best BTX selectivity,because it can satisfy both good ring-opening activity and sufficient butylbenzene cracking depth.展开更多
Hydrocracking is a catalytic reaction process in the petroleum refineries for converting the higher boiling temperature residue of crude oil into a lighter fraction of hydrocarbons such as gasoline and diesel. In this...Hydrocracking is a catalytic reaction process in the petroleum refineries for converting the higher boiling temperature residue of crude oil into a lighter fraction of hydrocarbons such as gasoline and diesel. In this study, a modified continuous lumping kinetic approach is applied to model the hydro-cracking of vacuum gas oil. The model is modified to take into consideration the reactor temperature on the reaction yield distribution. The model is calibrated by maximizing the likelihood function between the modeled and measured data at four different reactor temperatures. Bayesian approach parameter estimation is also applied to obtain the confidence interval of model parameters by considering the uncertainty associated with the measured errors and the model structural errors. Then Monte Carlo simulation is applied to the posterior range of the model parameters to obtain the 95% confidence interval of the model outputs for each individual fraction of the hydrocracking products. A good agreement is observed between the output of the calibrated model and the measured data points. The Bayesian approach based on the Markov Chain Monte Carlo simulation is shown to be efficient to quantify the uncertainty associated with the parameter values of the continuous lumping model.展开更多
The author makes a brief review of the history and the status quo of high pressure hydrocracking catalysts/processes development in China and gives out some thoughts and suggestions on the prospect of the said technol...The author makes a brief review of the history and the status quo of high pressure hydrocracking catalysts/processes development in China and gives out some thoughts and suggestions on the prospect of the said technology.展开更多
A novel hydrocracking Ni-W binary catalyst was tentatively designed and prepared by means ofimpregnation on mixed supports of modified Y zeolite and amorphous aluminosilicate . The structure andproperties of catalyst ...A novel hydrocracking Ni-W binary catalyst was tentatively designed and prepared by means ofimpregnation on mixed supports of modified Y zeolite and amorphous aluminosilicate . The structure andproperties of catalyst were extensively characterized by XRD, NH3-TPD, IR and XRF techniques. The perfor-mance of catalyst was evaluated by a 100-ml hydrogenation laboratory test unit with two single-stage fixed-bedreactors connected in series. The characterization results showed that the catalyst has a developed and con-centrated mesopores distribution, suitable acid sites and acid strength distribution, and uniform and highdispersion of metal sites. Under a high conversion rate of 73.8% with the >350℃ feedstock, a 98.1m% of C5+yield and 83.5% of middle distillates selectivity were obtained. The yield of middle distillates boiling between140℃and 370℃ was 68.70m% and its quality could meet the WWFC category III specification. It means thatthis catalyst could be used to produce more high quality clean middle distillates derived from heavy oilhydrocracking. The potential aromatic content of heavy naphtha from 65℃ to 140℃ was 37.5m%. The BMCIvalue of >370℃ tail oil was 6.6. The heavy naphtha and tail oil are premium feedstocks for catalytic reformingand steam cracker units.展开更多
In order to develop high-efficiency and low-cost catalyst for the slurry-phase hydrocracking of vacuum residue(VR),the catalyst supported on natural rectorite was prepared,and the effect of calcination modification of...In order to develop high-efficiency and low-cost catalyst for the slurry-phase hydrocracking of vacuum residue(VR),the catalyst supported on natural rectorite was prepared,and the effect of calcination modification of rectorite on the catalyst properties and performance was investigated.The support of rectorite and catalyst were characterized by XRD,FTIR,Py-FTIR,H_(2)-TPR and XPS to examine their structures and properties.The comparative reaction results show that VR conversions for the catalysts supported on calcined rectorite were similar with that on raw rectorite,possibly due to the VR cracking reaction controlled by the thermal cracking following free radical mechanism because of few acid sites observed on the catalysts surface.However,the yields of naphtha and middle distillates for the various catalysts were obviously different,and increased following as Rec-Mo(40.4 wt%)展开更多
Fischer-Tropsch synthesis(FTS)wax is a mixture of linear hydrocarbons with carbon number from C7 to C70+.Converting FTS wax into high-quality diesel(no sulfur and nitrogen contents)by hydrocracking technology is attra...Fischer-Tropsch synthesis(FTS)wax is a mixture of linear hydrocarbons with carbon number from C7 to C70+.Converting FTS wax into high-quality diesel(no sulfur and nitrogen contents)by hydrocracking technology is attractive in economy and practicability.Kinetic study of the hydrocracking of FTS wax in elementary step level is very challenging because of the huge amounts of reactions and species involved.Generation of reaction networks for hydrocracking of FTS wax in which the chain length goes up to C70 is described on the basis of Boolean adjacency matrixes.Each of the species(including paraffins,olefins and carbenium ions)involved in the elementary steps is represented digitally by using a(N+3)N matrix,in which a group of standardized numbering rules are designed to guarantee the unique identity of the species.Subsequently,the elementary steps are expressed by computer-aided matrix transformations in terms of proposed reaction rules.Dynamic memory allocation is used in species storage and a characteristic vector with nine elements is designed to store the key information of a(N+3)N matrix,which obviously reduces computer memory consumption and improves computing efficiency.The detailed reaction networks of FTS wax hydrocracking can be generated smoothly and accurately by the current method.The work is the basis of advanced elementary-step-level kinetic modeling.展开更多
Dividing-wall columns(DWCs)are widely used in the separation of ternary mixtures,but rarely seen in the separation of petroleum fractions.This work develops two novel and energy-efficient designs of lubricant-type vac...Dividing-wall columns(DWCs)are widely used in the separation of ternary mixtures,but rarely seen in the separation of petroleum fractions.This work develops two novel and energy-efficient designs of lubricant-type vacuum distillation process(LVDP)for the separation of hydroisomerization fractions(HIF)of a hydrocracking tail oil(HTO).First,the HTO hydroisomerization reaction is investigated in an experimental fixed-bed reactor to achieve the optimum liquid HIF by analyzing the impact of the operating conditions.A LVDP used for HIF separation is proposed and optimized.Subsequently,two thermal coupling intensified technologies,including side-stream(SC)and dividing-wall column(DWC),are combined with the LVDP to develop side-stream vacuum distillation process(SC-LVDP)and dividing-wall column vacuum distillation process(DWC-LVDP).The performance of LVDP,SC-LVDP,and DWC-LVDP are evaluated in terms of energy consumption,capital cost,total annual cost,product yields,and stripping steam consumption.The results demonstrates that the intensified processes,SC-LVDP and DWC-LVDP significantly decreases the energy consumption and capital cost compared with LVDP.DWC-LVDP further decreases in capital cost due to the removal of the side stripper and narrows the overlap between the third lube oils and fourth lube oils.This study attempts to combine DWC structure into the separation of petroleum fractions,and the proposed approach and the results presented provide an incentive for the industrial implementation of high-quality utilization of HTO through intensified LVDP.展开更多
基金supported by the National Key R&D Program of China(2021YFB3301100)Beijing University of Chemical Technology Interdisciplinary Program(XK2023-07).
文摘Corrosion leakages often occur in the air cooler of a hydrocracking unit,with the failure sites mainly located in the entrance area of the tubes.An analysis of the macroscopic morphology and corrosion products confirmed that the damage was caused by erosion-corrosion(E-C).Numerical and experimental methods were applied to investigate the E-C mechanism in the air cooler.Computational fluid dynamics(CFD)was used to calculate the hydrodynamic parameters of the air cooler.The results showed that there was a biased flow in the air cooler,which led to a significant increase in velocity,turbulent kinetic energy and wall shear within 0.2 m of the tube entrance.A visualization experiment was then performed to determine the principles of migration and transformation of multiphase flow in the air cooler tubes.Various flow patterns(pure droplet flow,mist flow,and annular flow)and their evolutionary processes were clearly depicted experimentally.The initiation mechanism and processes leading to the development of E-C in the air cooler were also determined.This study provided a comprehensive explanation for the E-C failures that occur in air coolers during operation.
文摘Hydroconversion of coal tar to produce aromatic hydrocarbons(BTX)represents a crucial strategy for the highvalue hierarchical utilization of coal.This study focused on the hydrocracking of hydrorefined products derived from coal tar to enhance the production of benzene,toluene,and xylene(BTX).Various reaction conditions,including reaction temperature,hydrogen pressure,space velocity,and hydrogen-to-oil volume ratio,were systematically explored to optimize BTX yields while also considering the process’s economic feasibility.The results indicate that increasing the reaction temperature from 360℃ to 390℃ significantly favors the production of BTX,with yields increasing from 21.42%to 41.14%.Similarly,an increase in hydrogen pressure from 4 MPa to 6 MPa boosts BTX production,with yields rising from 36.31%to 41.14%.Reducing the space velocity from 2 h^(-1) to 0.5 h^(-1) also favors the BTX production process,with yields increasing from 37.96%to 45.13%.Furthermore,raising the hydrogen-to-oil volume ratio from 750 to 1500 improves BTX yields from 41.61%to 45.44%.Through economic analysis,the optimal conditions for BTX production were identified as a reaction temperature of 390℃,hydrogen pressure of 5-6 MPa,space velocity of 1 h^(-1),and hydrogen-to-oil volume ratio of 1000,achieving a BTX yield of 43.73%.This investigation highlights the importance of a holistic evaluation of hydrocracking conditions to optimize BTX production.Furthermore,the findings offer valuable insights for the design and operation of industrial hydrocracking processes aimed at efficiently converting coal tar-derived hydrorefined feedstock into BTX.
基金National Key R&D Program of China(2021YFA1501203)is acknowledged for financial support.
文摘This paper reports the application of multi-component hydrocracking catalyst grading technology in diesel hydrocracking system to increase naphtha,and studies the influence of catalyst systems with different number of graded beds on the reaction process of diesel hydrocracking.Three hydrocracking catalysts with different physicochemical properties as gradation components,the diesel hydrocracking reaction on catalyst systems of one-component,two-component and three-component graded beds with different loading sequences are carried out and evaluated,respectively.The catalytic mechanism of the multi-component grading system is analyzed.The results show that,with the increase of the number of grading beds,the space velocity of reaction on each catalyst increases,which can effectively control the overreaction process;along the flow direction of feedstock,the loading sequences of catalysts with acidity decreasing and pore properties increasing can satisfy the demand of different catalytic activity for the conversion of reactant with changing composition to naphtha,which has a guiding role in the conversion of feedstock to target products.Therefore,the conversion of diesel,the selectivity and yield of naphtha all increase significantly on the multi-component catalyst system.The research on the grading technology of multi-component catalysts is of great significance to the promotion and application of catalyst systems in various catalytic fields.
基金The authors acknowledge National Key Research and Development Program of China(2018YFA0209403)National Natural Science Foundation of China(21908027)Qingyuan Innovation Laboratory Program(00121002)for financing this research.
文摘To deeply understand the effects of support properties on the performance of Mo-based slurry-phase hydrocracking catalysts,four Mo-based catalysts supported on amorphous silica alumina(ASA),γ-Al_(2)O_(3),ultra-stable Y(USY)zeolite and SiO_(2) were prepared by the incipient wetness impregnation method,respectively,and their catalytic performances were compared in the vacuum residue(VR)hydrocracking process.It is found that the Mo/ASA catalyst exhibits the highest VR conversion among the different catalysts,indicating that both the appropriate amount of acid sites,especially B acid sites and larger mesoporous volume of ASA can enhance the VR hydrocracking into light distillates.Furthermore,Mo catalysts supported on the different supports show quite different product distributions in VR hydrocracking.The Mo/ASA catalyst provides higher yields of naphtha and middle distillates and lower yields of gas and coke compared with other catalysts,it is attributed to the highest MoS_(2) slab dispersion,the highest sulfuration degree of Mo species,and the most Mo atoms located at the edge sites for the Mo/ASA catalyst,as observed by HRTEM and XPS analyses.These features of Mo/ASA are beneficial for the hydrogenation of intermediate products and polycyclic aromatic hydrocarbons to restrict the gas and coke formation.
基金National Natural Science Foundation of China(Grant No.21968034).
文摘A series of functionalized USY/SiO_(2) zeolite composite supports were synthesized using the coating coprecipitation method,with tetraethyl orthosilicate(TEOS)as the silicon source and different ratios of USY to TEOS.Active metals nickel(Ni)and molybdenum(Mo)were loaded onto the supports using the impregnation method.Finally,a series of hydrogenation catalysts were synthesized.The characterization results showed that,compared with the USY catalyst,the addition of a certain quantity of SiO_(2) resulted in the disappearance of the strong acid sites on the catalyst,the number of weak acid and medium strong acid sites decreased,and a certain number of secondary mesoporous structures were formed.The addition of SiO_(2) reduced the secondary cracking of benzene,toluene,xylene,and ethylbenzene(BTXE)effectively,while excessive amounts of SiO_(2) reduced the hydrogenation activity of the catalyst,leading to a decline in the final yield of BTXE.At a maximum SiO_(2) content of 45%,the hydrogenation depth of light cycle oil(LCO)reached an optimum value.The hydrogenation performance of LCO was investigated in a fixed bed reactor at 380℃,4 MPa,and H2/oil volume ratio of 800:1,where the gasoline and diesel fractions reached 80.00%and 16.74%,respectively.NiMo-YS45 had the highest BTXE selectivity,and the final yield of BTXE reached 21.27%.
文摘The upgrading of diesel oil to produce ethylene rich cracking feedstock is an important and promising technical route to reduce the ratio of diesel to gasoline. In the present work, a hydrocracking catalyst suitable for selective hydrocracking of straight run diesel oil to produce high-quality ethylene cracking feedstock at low cost was developed, by optimizing the composition of catalyst support materials, using amorphous silicon aluminum and aluminum oxide with high mesopore content as the main support, and modified Y zeolite with excellent aromatic ring opening selectivity as the acidic component. The catalyst has in-depth characterized by X-ray diffraction, transmission electron microscopy, scanning electron microscopy, N<sub>2</sub>-low temperature adsorption-desorption, NH<sub>3</sub>-temperature-programmed desorption, and IR techniques. And its catalytic cracking straight run diesel oil performance was evaluated. The results show that the prepared catalyst has high polycyclic aromatic hydrocarbon ring opening cracking selectivity. However, alkanes retained in diesel distillates can achieve the goal of producing more ethylene cracking feedstocks with low BMCI value under low and moderate pressure conditions. This work may shed significant technical insight for oil refining transformation.
基金financial supports by National Key R&D Program of China(Grant No.2017YFB0306702)are gratefully acknowledged。
文摘Nobel metallic Pt/ZSM-22 and Pt/ZSM-23 catalysts were prepared for hydroisomerization of normal dodecane and hydrodewaxing of heavy waxy lube base oil.The hydroisomerization performance of n-dodecane indicated that the Pt/ZSM-23 catalyst preferred to crack the C-C bond near the middle of n-dodecane chain,while the Pt/ZSM-22 catalyst was favorable for breaking the carbon chain near the end of n-dodecane.As a result,more than 2%of light products(gas plus naphtha)and3%more of heavy lube base oil with low-pour point and high viscosity index were produced on Pt/ZSM-22 than those on Pt/ZSM-23 while using the heavy waxy vacuum distillate oil as feedstock.
基金supported by the National Natural Science Foundation of China (Nos. 21878330, 21676298)the National Science and Technology Major Project, the CNPC Key Research Project (2016E-0707)the King Abdullah University of Science and Technology (KAUST) Office of Sponsored Research (OSR) under Award (No. OSR-2019-CPF-4103.2)。
文摘Light cycle oil(LCO) with high content of poly-aromatics was difficult to upgrade and convert,which had hindered upgrading fuel quality to meet with the standard of automotive diesel for the purpose of sustainable development.The hydrocracking behaviors of typical aromatics in LCO of naphthalene and tetralin were investigated over NiMo and CoMo catalysts.Several characterization methods including N2-adsoprtion and desorption,ammonia temperature-programmed desorption(NH3-TPD),Pyridine infrared spectroscopy(Py-IR),CO infrared spectroscopy(CO-IR),Raman and X-ray photoelectron spectroscopy(XPS) were applied to determine the properties of different catalysts.The results showed that CoMo catalyst with high concentration of S-edges could hydrosaturate more naphthalene to tetralin but exhibit lower yield of high-value light aromatics(carbon numbers less than 10) than NiMo catalyst.NiMo catalyst with high concentration of Mo-edges also presented a higher selectivity of converting naphthalene into cyclanes than CoMo catalyst.Subsequently,the naphthalene and LCO hydrocracking performances were also investigated over different catalysts systems.The activity evaluation and kinetic analysis results showed that the naphthalene hydrocracking conversion and the yield of light aromatics for CoMo-AY/NiMo-AY grading catalysts were higher than NiMo-AY/CoMo-AY grading catalysts at same condition.A stepwise reaction principle was proposed to explain the high efficiency of CoMo-AY/NiMoAY grading catalysts.Finally,the LCO hydrocracking evaluation results confirmed that CoMo-AY/NiMoAY catalysts grading system with low carbon deposition and high stability could remain high percentage of active phases,which was more efficient to convert LCO to high-octane gasoline.
基金Financial support from the National Natural Science Foundation of China (21968034) is gratefully acknowledged.
文摘In this work,NiMo catalysts with various contents of MoO_(3)were prepared through incipient wetness impregnation by a twostep method(NMxA)and onepot method(NMxB).The catalysts were then characterized by XRD,XPS,NH3TPD,H_(2)TPR,HRTEM,and N_(2)adsorptiondesorption technologies.The performance of the NiMo/Al_(2)O_(3) catalysts was investigated by hydrocracking lowtemperature coal tar.When the MoO3 content was 15 wt%,the interaction between Ni species and Al_(2)O_(3) on the NM15B catalyst was stronger than that on the NM15A catalyst,resulting in the poor performance of the former.When the MoO^(3) content was 20 wt%,MoO_(3) agglomerated on the surface of the NM20A catalyst,leading to decreased number of active sites and specific surface area and reduced catalytic performance.The increase in the number of MoS_(2) stack layers strengthened the interaction between Ni and Mo species of the NM20B catalyst and consequently improved its catalytic performance.When the MoO_(3) content reached 25 wt%,the active metals agglomerated on the surface of the NiMo catalysts,thereby directly decreasing the number of active sites.In conclusion,the twostep method is suitable for preparing catalysts with large pore diameter and low MoO_(3) content loading,and the onepot method is more appropriate for preparing catalysts with large specific surface area and high MoO_(3) content.Moreover,the NMxA catalysts had larger average pore diameter than the NMxB catalysts and exhibited improved desulfurization performance.
基金supported by the Grant APVV-15-0148 provided by the Slovak Research and Development Agency
文摘One of the commercial means to convert heavy oil residue is hydrocracking in an ebullated bed. The ebullated bed reactor includes a complex gas–liquid–solid backmixed system which attracts the attention of many scientists and research groups. This work is aimed at the calculation of the internal recycle flow rate and understanding its effect on other parameters of the ebullated bed. Measured data were collected from an industrial scale residual hydrocracking unit consisting of a cascade of three ebullated bed reactors. A simplified block model of the ebullated bed reactors was created in Aspen Plus and fed with measured data. For reaction yield calculation, a lumped kinetic model was used. The model was verified by comparing experimental and calculated distillation curves as well as the calculated and measured reactor inlet temperature. Influence of the feed rate on the recycle ratio(recycle to feed flow rate) was estimated. A relation between the recycle flow rate, pump pressure difference and catalyst inventory has been identified. The recycle ratio also affects the temperature gradient along the reactor cascade. Influence of the recycle ratio on the temperature gradient decreased with the cascade member order.
文摘In this study,selective dealumination of Beta zeolites was performed through partially removing the templating agent in Beta zeolites by calcination and then removing the aluminum on the external surface of Beta zeolites with acid treatment.Hydrocracking catalysts were prepared by loading WO_(3)onto these dealuminated Beta zeolites.It was shown that the surface SiO_(2)/Al_(2)O_(3)of selectively dealuminated Beta zeolites was higher than that of conventionally dealuminated samples for the same bulk SiO_(2)/Al_(2)O_(3),and the hydrogenation activity of the catalyst of the selectively dealuminated Beta zeolites was lower than that of conventionally dealuminated Beta zeolites.The experimental results for tetralin hydrocracking to BTX showed that the catalysts based on the selectively dealuminated Beta zeolites had higher BTX selectivity and lower coke formation rate than that the catalysts based on the conventionally dealuminated Beta zeolites.
基金This work was financially supported by the SINOPEC Science and technology Development Funds(No.12005-1)the Hydrogenation Process and Hydrogenation Catalyst Laboratory(RIPP,SINOPEC).
文摘Conversion of LCO(light cycle oil)to BTX(benzene,toluene,and xylene)is an economically valuable method for refineries.However,this approach still faces difficulties as the main reactions are not clearly understood.Here we study the detailed hydrocracking pathway of typical reactants,1-methylnaphthalene and tetralin,through molecular simulations and experiments to improve our understanding of the conversion process of LCO to BTX.Molecular simulations demonstrate that the rate-determining step is the isomerization pathway of six-membered ring to five-membered ring in tetralin as its activation energy(ΔEa)is the highest among all the reactions and the order ofΔEa of reactions is isomerization>ring-opening≈side-chain cleavage.The results of experiments show that with the increase in reaction depth,i.e.,through a high temperature(350-370℃)and low LHSV(4.5-6.0 h^(−1)),isomerization,ring-opening,and side-chain cleavage reactions occurred,thus improving the selectivity and yield of alkyl aromatics.
文摘Three different zeolite catalysts with different pore sizes(MFI-type,BEA-type,and FAU-type zeolites)have been prepared.The influence of different zeolite catalysts on reactivity and product shape selectivity of tetralin is investigated.Clear differences are observed in the reactivity of tetralin and distribution of products achieved by different catalysts.The diffusion and adsorption behavior of the reactant tetralin and its intermediates,n-butylbenzene and 1-methylindane under the reaction conditions are simulated using molecular simulation methods.Upon combining simulation results and experimental observations,it is shown that the difference in diffusion coefficient and competitive adsorption capacity can explain the reactivity of tetralin and the selectivity of products.The steric hindrance of the MFI-type zeolite mainly limits the key step of ring opening of tetralin,leading to lower selectivity of ring-opening products.n-Butylbenzene molecules can diffuse sufficiently fast in the large pores of FAU-type zeolite and the weak adsorption capacity of n-butylbenzene leads to its insufficient cracking.In addition,it also explains the reason that the BEA-type zeolite has the best BTX selectivity,because it can satisfy both good ring-opening activity and sufficient butylbenzene cracking depth.
文摘Hydrocracking is a catalytic reaction process in the petroleum refineries for converting the higher boiling temperature residue of crude oil into a lighter fraction of hydrocarbons such as gasoline and diesel. In this study, a modified continuous lumping kinetic approach is applied to model the hydro-cracking of vacuum gas oil. The model is modified to take into consideration the reactor temperature on the reaction yield distribution. The model is calibrated by maximizing the likelihood function between the modeled and measured data at four different reactor temperatures. Bayesian approach parameter estimation is also applied to obtain the confidence interval of model parameters by considering the uncertainty associated with the measured errors and the model structural errors. Then Monte Carlo simulation is applied to the posterior range of the model parameters to obtain the 95% confidence interval of the model outputs for each individual fraction of the hydrocracking products. A good agreement is observed between the output of the calibrated model and the measured data points. The Bayesian approach based on the Markov Chain Monte Carlo simulation is shown to be efficient to quantify the uncertainty associated with the parameter values of the continuous lumping model.
文摘The author makes a brief review of the history and the status quo of high pressure hydrocracking catalysts/processes development in China and gives out some thoughts and suggestions on the prospect of the said technology.
文摘A novel hydrocracking Ni-W binary catalyst was tentatively designed and prepared by means ofimpregnation on mixed supports of modified Y zeolite and amorphous aluminosilicate . The structure andproperties of catalyst were extensively characterized by XRD, NH3-TPD, IR and XRF techniques. The perfor-mance of catalyst was evaluated by a 100-ml hydrogenation laboratory test unit with two single-stage fixed-bedreactors connected in series. The characterization results showed that the catalyst has a developed and con-centrated mesopores distribution, suitable acid sites and acid strength distribution, and uniform and highdispersion of metal sites. Under a high conversion rate of 73.8% with the >350℃ feedstock, a 98.1m% of C5+yield and 83.5% of middle distillates selectivity were obtained. The yield of middle distillates boiling between140℃and 370℃ was 68.70m% and its quality could meet the WWFC category III specification. It means thatthis catalyst could be used to produce more high quality clean middle distillates derived from heavy oilhydrocracking. The potential aromatic content of heavy naphtha from 65℃ to 140℃ was 37.5m%. The BMCIvalue of >370℃ tail oil was 6.6. The heavy naphtha and tail oil are premium feedstocks for catalytic reformingand steam cracker units.
基金National Key Research and Development program(2018YFA0209403)National Natural Science Foundation of China(Youth)program(21908027)for financing this research。
文摘In order to develop high-efficiency and low-cost catalyst for the slurry-phase hydrocracking of vacuum residue(VR),the catalyst supported on natural rectorite was prepared,and the effect of calcination modification of rectorite on the catalyst properties and performance was investigated.The support of rectorite and catalyst were characterized by XRD,FTIR,Py-FTIR,H_(2)-TPR and XPS to examine their structures and properties.The comparative reaction results show that VR conversions for the catalysts supported on calcined rectorite were similar with that on raw rectorite,possibly due to the VR cracking reaction controlled by the thermal cracking following free radical mechanism because of few acid sites observed on the catalysts surface.However,the yields of naphtha and middle distillates for the various catalysts were obviously different,and increased following as Rec-Mo(40.4 wt%)
基金supported by the National Key Research&Development Program of China(2020YFB0606404)National Natural Science Foundation of China(21908234)。
文摘Fischer-Tropsch synthesis(FTS)wax is a mixture of linear hydrocarbons with carbon number from C7 to C70+.Converting FTS wax into high-quality diesel(no sulfur and nitrogen contents)by hydrocracking technology is attractive in economy and practicability.Kinetic study of the hydrocracking of FTS wax in elementary step level is very challenging because of the huge amounts of reactions and species involved.Generation of reaction networks for hydrocracking of FTS wax in which the chain length goes up to C70 is described on the basis of Boolean adjacency matrixes.Each of the species(including paraffins,olefins and carbenium ions)involved in the elementary steps is represented digitally by using a(N+3)N matrix,in which a group of standardized numbering rules are designed to guarantee the unique identity of the species.Subsequently,the elementary steps are expressed by computer-aided matrix transformations in terms of proposed reaction rules.Dynamic memory allocation is used in species storage and a characteristic vector with nine elements is designed to store the key information of a(N+3)N matrix,which obviously reduces computer memory consumption and improves computing efficiency.The detailed reaction networks of FTS wax hydrocracking can be generated smoothly and accurately by the current method.The work is the basis of advanced elementary-step-level kinetic modeling.
基金funded by Shanghai Sailing Program (No.19YF1410800)National Natural Science Foundation of China(No. 21908056)。
文摘Dividing-wall columns(DWCs)are widely used in the separation of ternary mixtures,but rarely seen in the separation of petroleum fractions.This work develops two novel and energy-efficient designs of lubricant-type vacuum distillation process(LVDP)for the separation of hydroisomerization fractions(HIF)of a hydrocracking tail oil(HTO).First,the HTO hydroisomerization reaction is investigated in an experimental fixed-bed reactor to achieve the optimum liquid HIF by analyzing the impact of the operating conditions.A LVDP used for HIF separation is proposed and optimized.Subsequently,two thermal coupling intensified technologies,including side-stream(SC)and dividing-wall column(DWC),are combined with the LVDP to develop side-stream vacuum distillation process(SC-LVDP)and dividing-wall column vacuum distillation process(DWC-LVDP).The performance of LVDP,SC-LVDP,and DWC-LVDP are evaluated in terms of energy consumption,capital cost,total annual cost,product yields,and stripping steam consumption.The results demonstrates that the intensified processes,SC-LVDP and DWC-LVDP significantly decreases the energy consumption and capital cost compared with LVDP.DWC-LVDP further decreases in capital cost due to the removal of the side stripper and narrows the overlap between the third lube oils and fourth lube oils.This study attempts to combine DWC structure into the separation of petroleum fractions,and the proposed approach and the results presented provide an incentive for the industrial implementation of high-quality utilization of HTO through intensified LVDP.
