We presented a strategy to prepare spherical tungsten powder by the combination of hydrothermal method and H2reduction process.In hydrothermal process,the micelle of tetraethylammonium bromide(TEAB)act as spherical te...We presented a strategy to prepare spherical tungsten powder by the combination of hydrothermal method and H2reduction process.In hydrothermal process,the micelle of tetraethylammonium bromide(TEAB)act as spherical templates for the deposition of tungsten oxide,whereas the excessive TEAB inhibit the formation of spherical tungsten oxide due to the dense molecular layer of TEAB on the tungsten oxide particles.Citric acid(CA)can control the formation rate and structure of the tungsten oxide when its concentration is more than 0.2 mol/L,because of its ability to coordinate with tungsten atoms.The synergistic effect of TEAB and CA facilitates the formation of spherical tungsten oxide with nanorod crown.After being treated by H_(2)at 600 and 650℃,the tungsten oxide particles are reduced to tungsten particles,which maintain the spherical structure of tungsten oxide and have porous structure.展开更多
In this experiment, Cu<sup>2+</sup> doped ZnO (Cu-ZnO) nanorods materials have been fabricated by hydrothermal method. Cu<sup>2+</sup> ions were doped into ZnO with ratios of 2, 5 and 7 mol.% (...In this experiment, Cu<sup>2+</sup> doped ZnO (Cu-ZnO) nanorods materials have been fabricated by hydrothermal method. Cu<sup>2+</sup> ions were doped into ZnO with ratios of 2, 5 and 7 mol.% (compared to the mole’s number of Zn<sup>2+</sup>). The hexamethylenetetramine (HMTA) solvent used for the fabrication of Cu-ZnO nanorods with the mole ratio of Zn<sup>2+</sup>:HMTA = 1:4. The characteristics of the materials were analyzed by techniques, such as XRD, Raman shift, SEM and UV-vis diffuse reflectance spectra (DRS). The photocatalytic properties of the materials were investigated by the decomposition of the methylene blue (MB) dye solution under ultraviolet light. The results show that the size of Cu-ZnO nanorods was reduced when the Cu<sup>2+</sup> doping ratio increased from 2 mol.% to 7 mol.%. The decomposition efficiency of the MB dye solution reached 92% - 97%, corresponding to the Cu<sup>2+</sup> doping ratio changed from 2 - 7 mol.% (after 40 minutes of ultraviolet irradiation). The highest efficiency for the decomposition of the MB solution was obtained at a Cu<sup>2+</sup> doping ratio of 2 mol.%.展开更多
The coal gangue as the only source of silicon and aluminum was employed to synthesize sodalite and faujasite using hydrothermal method,which directly treated the mixture of pre-treated coal gangue and NaOH solution un...The coal gangue as the only source of silicon and aluminum was employed to synthesize sodalite and faujasite using hydrothermal method,which directly treated the mixture of pre-treated coal gangue and NaOH solution under hydrothermal environment.X-ray powder diffraction analysis(XRD),thermogravimetry analysis(TG)and differential thermogravimetry analysis(DTG),scanning electron microscopy(SEM),high resolution transmission electron microscopy(HRTEM),N_(2)adsorption-desorption technique,X-ray photoelectron spectroscopy(XPS),etc.were used to characterize the samples.Cd^(2+) ion was used to evaluate the heavy metal ions removal performance of the samples.The experimental results show that the coal gangue,which consists of quartz,calcium feldspar,potassium feldspar and kaolinite,can transform to sodalite and faujasite under alkali-hydrothermal condition at 150 and 180℃,respectively.The as-prepared sodalite and faujasite can effectively remove the simulated Cd2+ion wastewater and actual industrial wastewater containing As^(3+),Cd^(2+),and Cr^(3+)ions,and the good heavy metal ion removal performance of the zeolites is mainly attributed to their low Si/Al ratio and high Na+content.This alkali-hydrothermal method appears to be a simple and efficient method for transformation of coal gangue to high purity zeolites.展开更多
Tetragonal barium titanate was synthesized from barium hydroxide octahydrate and titanium tetrachloride through a simple one-step hydrothermal method.The effect of different solvents on the crystal structure and morph...Tetragonal barium titanate was synthesized from barium hydroxide octahydrate and titanium tetrachloride through a simple one-step hydrothermal method.The effect of different solvents on the crystal structure and morphology of barium titanate nanoparticles during the hy-drothermal process was investigated.Except for ethylene glycol/water solvent,impurity-free barium titanate was synthesized in pure water,methanol/water,ethanol/water,and isopropyl alcohol/water mixed solvents.Compared with other alcohols,ethanol promotes the formation of a tetragonal structure.In addition,characterization studies confirm that particles synthesized in methanol/water,ethanol/water,and isopropyl al-cohol/water mixed solvents are smaller in size than those synthesized in pure water.In the case of alcohol-containing solvents,the particle size decreases in the order of isopropanol,ethanol,and methanol.Among all the media used in this study,ethanol/water is considered the optimum reaction media for barium titanate with high tetragonality(defined as the ratio of two lattice parameters c and a,c/a=1.0088)and small aver-age particle size(82 nm),which indicates its great application potential in multilayer ceramic capacitors.展开更多
LiCoPO4 micron-rods with an average diameter of about 500 nm and length of about 5 μm were synthesized by dispersant-aided hydrothermal method. Poly(n-vinylpyrrolidone) (PVP) was used as dispersant in the hydrotherma...LiCoPO4 micron-rods with an average diameter of about 500 nm and length of about 5 μm were synthesized by dispersant-aided hydrothermal method. Poly(n-vinylpyrrolidone) (PVP) was used as dispersant in the hydrothermal method. The starting solution and the concentration of dispersant have significant influences on the morphology of LiCoPO4,and the electrochemical performance is improved via controlling the particle size and morphology by the hydrothermal method. The cell using smaller particle LiCoPO4 as cathode delivers a larger capacity and lower cell polarization.展开更多
NaTaO_(3-x)N_x catalysts were synthesized by a hydrothermal(H) and a solid-state(S) methods in this study.The H-and S-NaTaO_(3-x)N_x samples were characterized by X-ray diffraction(XRD), scanning electron microscopy(S...NaTaO_(3-x)N_x catalysts were synthesized by a hydrothermal(H) and a solid-state(S) methods in this study.The H-and S-NaTaO_(3-x)N_x samples were characterized by X-ray diffraction(XRD), scanning electron microscopy(SEM), transmission electron microscopy(TEM), UV–visible(UV–vis) diffuse reflectance spectroscopy, and photoluminescence(PL) spectroscopy. The XRD patterns of the H-and S-samples showed peaks indexed to the pure phase of perovskite NaTaO_3 and minor peaks assignable to Ta_3N_5 at various synthesis temperatures. Substitution of oxygen by nitrogen ions causes the light absorption of the H-and S-NaTaO_(3-x)N_x samples to be extended to the 600–650 nm region, thus making the samples visible-light active. The NaTaO_(3-x)N_x samples exhibited photocatalytic activity for H_2 and O_2 evolution from aqueous methanol and silver nitrate solutions under visible-light irradiation. The UV–vis and PL spectra of the Hand S-catalysts revealed the presence of cationic vacancies and reduced metallic species, which acted as recombination centers. These results demonstrated that the preparation method plays a critical role in the formation of defect states, thereby governing the photocatalytic activity of the NaTaO_(3-x)N_x catalysts.展开更多
Hydro-sodalites are zeolitic materials with a wide variety of applications.Fly ash is an abundant industrial solid waste,rich in silicon and aluminum,from which hydro-sodalite can be synthesized.However,traditional hy...Hydro-sodalites are zeolitic materials with a wide variety of applications.Fly ash is an abundant industrial solid waste,rich in silicon and aluminum,from which hydro-sodalite can be synthesized.However,traditional hydrothermal synthesis methods are complex and cannot produce high-purity products.Therefore,there is a demand for processing routes to obtain high-purity hydro-sodalites.In the present study,high-purity hydro-sodalite(90.2 wt%)was prepared from fly ash by applying a hydrothermal method to a submolten salt system.Samples were characterized by powder X-ray diffraction(XRD),scanning electron microscopy(SEM),thermogravimetry and differential thermal analysis(TG–DTA),and Fourier transform infrared spectroscopy(FTIR)to confirm and quantify conversion of the raw material into the product phase.Purity of the samples prepared with an H2O/Na OH mass ratio of 1.5 and an H2O/fly ash mass ratio of 10 was calculated and the conversion process of the product phase was studied.Crystallinity of the product was influenced more by the Na OH concentration,less by the H2O/fly ash mass ratio.The main reaction process of the system is that the Si O ions produced by dissolution of the vitreous body in the fly ash and Na+ions in the solution reacted on the destroyed mullite skeleton to produce hydro-sodalite.This processing route could help mitigate processing difficulties,while producing high-purity hydro-sodalite from fly ash.展开更多
α-calcium sulfate hemihydrate (α-HH) is known to be suitable for application as bone void filler. High percentage of α-HH is obviously needed for medical applications, especially for implantation. Three commerciall...α-calcium sulfate hemihydrate (α-HH) is known to be suitable for application as bone void filler. High percentage of α-HH is obviously needed for medical applications, especially for implantation. Three commercially available calcium sulfate dihydrates (DH, CaSO4·2H2O) with different sizes and surface morphologies were used as starting materials to synthesize high percentage α-HH via a hydrothermal method. The median particle sizes of the three types of DH were 946.7 μm, 162.4 μm and 62.4 μm, respectively. They were named as DH-L, DH-M and DH-S in this paper. The particle size distribution, morphology and phase composition of the raw materials were evaluated before synthesis. SEM results revealed that DH-L consisted of irregular large particles, while DH-M and DH-S were composed of plate-like particles with some small ones. High percentage HH can be obtained with proper synthesis parameters by hydrothermal method, specifically, 105 °C/90 min for DH-L (achieving 98.8% HH), 105°C/30 min for DH-M (achieving 96.7% HH) and 100°C/45 min for DH-S (achieving 98.4% HH). All the synthesized HH were hexagonal columns, demonstrating that they were α-phase HH. The particle size and morphology of starting material (DH) have significant influences on not only the rate of phase transition but also the morphology of the synthesized α-HH. Calcium sulfate dihydrate cements were prepared by the synthesized α-HH. The highest compressive strength of calcium sulfate dihydrate cement was 17.2 MPa. The results show that the preparation of high percentage α-HH is feasible via a hydrothermal method and the process can be further scaled up to industrial scale production.展开更多
A microemulsion-mediated hydrothermal method for synthesis of YVO4:RE(RE=Yb 3+/Er 3+,Yb 3+/Tm 3+)nanoparticles by hydrothermal treatment of quaternary microemulsion medium consisting of Na3VO4/NaOH and RE(NO3)3 aqueou...A microemulsion-mediated hydrothermal method for synthesis of YVO4:RE(RE=Yb 3+/Er 3+,Yb 3+/Tm 3+)nanoparticles by hydrothermal treatment of quaternary microemulsion medium consisting of Na3VO4/NaOH and RE(NO3)3 aqueous solution, surfactant cetyltrimethylammonium bromide(CTAB),cosurfactant n-hexanol and oil phase n-heptane was report.The confinement of microemulsion droplets acting as microreactors during the reaction process allows the formation of small size YVO4:RE nanoparticles with relatively narrow size distribution and less aggregation.The structure,size and shape of YVO4:RE nanoparticles were investigated by means of X-ray diffractometry(XRD)and transmission electron microscopy(TEM).Compared with the conventional solid annealing diffusion method,the microemulsion-mediated hydrothermal method shows superiority in obtaining YVO4:RE nanoparticles with controllable size,narrow size distribution and less aggregation.The microemulsion-mediated hydrothermal method may be potentially applicable for synthesis of other rare earth doped up-converting luminescence nanomaterials.展开更多
Vertically oriented ZnO nanorods have been synthesized by hydrothermal method on quartz substrates with a seed layer. The influence of solution concentration on the morphology, structural and optical properties was an...Vertically oriented ZnO nanorods have been synthesized by hydrothermal method on quartz substrates with a seed layer. The influence of solution concentration on the morphology, structural and optical properties was analyzed. Results indicated that with the increase of solution concentration, the diameter and uniformity of ZnO nanorods increased. And the preferred orientation is obviously which shows better crystal quality. Typically, when the solution concentration is 0.03 mol/L, the nanorods exhibit a stronger UV emission peak located around 380 nm. In the visible region, all synthesized samples demonstrate more than 80% of optical transparency.展开更多
Hydrothermal method was used to synthesize nanoscale particles of MnZn ferrites. The crystallites were characterized by XRD, TEM and SEM. The effects of the reaction time, temperature and additives on the product were...Hydrothermal method was used to synthesize nanoscale particles of MnZn ferrites. The crystallites were characterized by XRD, TEM and SEM. The effects of the reaction time, temperature and additives on the product were investigated. Crystallization process would be carried out above 160 ℃ for 5 h or more, higher temperature can reduce the reaction time. Additives were used to remove impurities such as Fe 2O 3, ZnMnO 3.10～15 nm pure slightly agglomerated MnZn ferrite crystallites with a narrow grain size distribution were obtained.展开更多
Magnesium hydroxide(Mg(OH)_2) nanorods were synthesized by a simple and facile hydrothermal method in the presence of cetyltetramethylammonium bromide(CTAB) as a surfactant. Nanorods of magnesium oxide Mg O were also ...Magnesium hydroxide(Mg(OH)_2) nanorods were synthesized by a simple and facile hydrothermal method in the presence of cetyltetramethylammonium bromide(CTAB) as a surfactant. Nanorods of magnesium oxide Mg O were also induced by thermal decomposition of Mg(OH)_2 nanorods at 700. By using disk diffusion technique, the Mg(OH)_2 nanorods were found to exhibit higher antibacterial efficiency against several tested bacterial strains.展开更多
In this paper, we have demonstrated a facile and low-cost synthesis of the ZnO/CuO nanocomposites by two-step hydrothermal methods. The photocatalytic properties of the as-synthesized ZnO/CuO nanocomposites have been ...In this paper, we have demonstrated a facile and low-cost synthesis of the ZnO/CuO nanocomposites by two-step hydrothermal methods. The photocatalytic properties of the as-synthesized ZnO/CuO nanocomposites have been evaluated by the photodegradation of methylene blue(MB) and methyleneorange(MO) under UV irradiation. Experimental results show that MB and MO can be degraded completely within 15 and 25 min by the ZnO/CuO nanocomposites and its photodegradation rate is 6 times faster than that of pure ZnO. This enhanced photocatalytic activity can be ascribed to the low recombination probability of photo-induced carriers due to the efficient charge transfer in the nanocomposites. The as-synthesized ZnO/CuO nanocomposite may be a promising candidate for dye photodegradation of wastewaters.展开更多
TiO_2 nanoparticles(NPs)were prepared via the hydrothermal route of TiO_2 xerogel in nitric acid, hydrochloric acid and acetic acid. The physico-chemical properties of the powders were characterized by X-ray diffracti...TiO_2 nanoparticles(NPs)were prepared via the hydrothermal route of TiO_2 xerogel in nitric acid, hydrochloric acid and acetic acid. The physico-chemical properties of the powders were characterized by X-ray diffraction(XRD)and N_2 adsorption desorption techniques. The effects of the different acids on the structure(crystal phase)and texture(primary particle size and porosity)of the TiO_2 powders were explored. Results indicated that acetic acid facilitated the formation and stability of pure anatase phase. On the other hand, nitric acid and hydrochloric acid led to the transformation from anatase to rutile. The catalyst synthesized via the hydrothermal route of TiO_2 xerogel in the low concentration hydrochloric acid solution(Ti-HCl-0.15)had the highest photocatalytic activity than the catalysts obtained in the other two acid solutions. The effects of the different acids were discussed in terms of acid strength, chelating effect and the thermal stability of the adsorbed acidic anions.展开更多
The aim of this study was to investigate the hemicelluloses extracted from Populus tomentosa Carr.by the hydrothermal method with ethanol.The influence of ethanol concentration on the hemicellulosic fractions was syst...The aim of this study was to investigate the hemicelluloses extracted from Populus tomentosa Carr.by the hydrothermal method with ethanol.The influence of ethanol concentration on the hemicellulosic fractions was systematically studied.The chemical compositions and structural features of the hemicellulosic fractions were investigated by a combination of sugar analysis,gel-permeation chromatography,Fourier transform infrared spectroscopy,and one-dimensional proton and carbon-13 nuclear magnetic resonance,and two-dimensional heteronuclear single quantum coherence spectroscopy.Neutral sugar analysis of the hemicellulosic fractions revealed that a higher ethanol concentration(45%~80%) favored the isolation of hemicelluloses with more side chains and lower glucose contents.The molecular weights of these polysaccharides ranged between 2842 g/mol and 5101 g/mol.The results of this study indicate that the hydrothermal ethanol process provides a new pretreatment strategy for the isolation and extraction of biomass.展开更多
The resistive switching characteristics of TiO_2 nanowire networks directly grown on Ti foil by a single-step hydrothermal technique are discussed in this paper. The Ti foil serves as the supply of Ti atoms for growth...The resistive switching characteristics of TiO_2 nanowire networks directly grown on Ti foil by a single-step hydrothermal technique are discussed in this paper. The Ti foil serves as the supply of Ti atoms for growth of the TiO_2 nanowires, making the preparation straightforward. It also acts as a bottom electrode for the device. A top Al electrode was fabricated by e-beam evaporation process. The Al/TiO_2 nanowire networks/Ti device fabricated in this way displayed a highly repeatable and electroforming-free bipolar resistive behavior with retention for more than 10~4 s and an OFF/ON ratio of approximately 70. The switching mechanism of this Al/TiO_2 nanowire networks/Ti device is suggested to arise from the migration of oxygen vacancies under applied electric field. This provides a facile way to obtain metal oxide nanowire-based Re RAM device in the future.展开更多
High quality potassium hexatitanate whiskers were hydrothermally synthesized in one step under moderate temperature and pressure condi-tions. Effects of the titanium source and reaction conditions on the hydrothermal ...High quality potassium hexatitanate whiskers were hydrothermally synthesized in one step under moderate temperature and pressure condi-tions. Effects of the titanium source and reaction conditions on the hydrothermal reaction rate, product phase component, and morphology of whiskers were investigated. The results show that the reactivity of hydrated titania, anatase TiO2, and rutile TiO2 with KOH decreases in turn, and with hydrated titania as titanium source, it is difficult to obtain potassium hexatitanate whiskers with good morphology. In contrast, uni-form potassium hexatitanate whiskers with a length of 10-20 μm and a diameter of 200-700 nm were obtained using anatase TiO2 as titanium source. The investigation demonstrates that the initial KOH concentration, annealing temperature and time, molar ratio of K2O/TiO2, etc. sig-nificantly affect the morphology of the as-synthesized whiskers. The optimized synthesis condition is as follows: anatase as a titanium source; 10 wt.% KOH solution; annealing temperature and time of 300°C and 5 h, respectively; K2O/TiO2 molar ratio of 5, etc. A rhombic potassium hexatitanate was prepared under the optimum condition and the whisker grew along the [110] direction. The reaction mechanism was dis-cussed.展开更多
Nanocrystal of upconversion （UC） phosphor Ho 3+ , Tm 3+ , and Yb 3+ co-doped NaYF4 was prepared by the hydrothermal method in the presence of the complexing agent EDTA. Under 980 nm diode laser excitation, the impac...Nanocrystal of upconversion （UC） phosphor Ho 3+ , Tm 3+ , and Yb 3+ co-doped NaYF4 was prepared by the hydrothermal method in the presence of the complexing agent EDTA. Under 980 nm diode laser excitation, the impact of different concentrations of Ho 3+ ion on the UC luminescence intensity was discussed. The law of luminescence intensity versus pump power shows that the 474 nm blue emission, 538 nm green emission, and 642 nm red emission are all due to the two-photon process, while the 450 nm blue emission is a three-photon process. The UC mechanism and processes were also analyzed. The sample was characterized by transmission electron microscopy （TEM） and X-ray diffraction （XRD）. The result shows that Ho 3+ , Tm 3+ , and Yb 3+ co-doped NaYF4 prepared by the hydrothermal method exhibits a hexagonal nanocrystal.展开更多
The Ni(OH)2/SiO2 binary colloid was prepared using Ni(NO3)2.6H2O and (C2H5 O)4SiO4 as starting materials and was used to form NiO/SiO2 composite powder by hydrothermal method and desiccant method in open air respectiv...The Ni(OH)2/SiO2 binary colloid was prepared using Ni(NO3)2.6H2O and (C2H5 O)4SiO4 as starting materials and was used to form NiO/SiO2 composite powder by hydrothermal method and desiccant method in open air respectively. Multiwalled carbon nanotubes (MWCNTs) were synthesized respectively by chemical vapor deposition using the NiO/SiO2 catalyst prepared by different methods. The phase and morphology of the catalysts and the morphology, output yield and purity of MWCNTs were compared by XRD, TEM and SEM. The results show that the catalyst powder prepared by hydrothermal method, compared with that by desiccant method, is smaller, better dispersion and has stronger catalytic activity. Pure MWCNTs with smaller tube diameter and narrow range could be obtained at a high yield using that NiO/SiO.2 powder prepared by hydrothermal method as catalyst.展开更多
Semiconducting zinc oxide (ZnO) nanorods were obtained in bulk quantity by an hexamethylenetetramine (HMTA)-assisted hydrothermal method at low temperature (90°C) with methenamine ((CH3)6N4 as surfactant and cata...Semiconducting zinc oxide (ZnO) nanorods were obtained in bulk quantity by an hexamethylenetetramine (HMTA)-assisted hydrothermal method at low temperature (90°C) with methenamine ((CH3)6N4 as surfactant and catalyst and zinc nitrate Zn(NO3)2·6H2O as Zn source. The structure and phase of ZnO nanorods were studied using x-ray diffraction (XRD) and high resolution transmission electron microscopy techniques (HRTEM). The morphology of the nanostructures was studied by scanning electron microscope (SEM) method. The photoluminescence (PL) properties were investigated founding two emission bands under UV excitation.展开更多
基金Funded by the Key Program of Jiangxi Province on Development and Research(No.20203BBE53058)the Key Program of Ganzhou City on Development and Research(No.202101125003)。
文摘We presented a strategy to prepare spherical tungsten powder by the combination of hydrothermal method and H2reduction process.In hydrothermal process,the micelle of tetraethylammonium bromide(TEAB)act as spherical templates for the deposition of tungsten oxide,whereas the excessive TEAB inhibit the formation of spherical tungsten oxide due to the dense molecular layer of TEAB on the tungsten oxide particles.Citric acid(CA)can control the formation rate and structure of the tungsten oxide when its concentration is more than 0.2 mol/L,because of its ability to coordinate with tungsten atoms.The synergistic effect of TEAB and CA facilitates the formation of spherical tungsten oxide with nanorod crown.After being treated by H_(2)at 600 and 650℃,the tungsten oxide particles are reduced to tungsten particles,which maintain the spherical structure of tungsten oxide and have porous structure.
文摘In this experiment, Cu<sup>2+</sup> doped ZnO (Cu-ZnO) nanorods materials have been fabricated by hydrothermal method. Cu<sup>2+</sup> ions were doped into ZnO with ratios of 2, 5 and 7 mol.% (compared to the mole’s number of Zn<sup>2+</sup>). The hexamethylenetetramine (HMTA) solvent used for the fabrication of Cu-ZnO nanorods with the mole ratio of Zn<sup>2+</sup>:HMTA = 1:4. The characteristics of the materials were analyzed by techniques, such as XRD, Raman shift, SEM and UV-vis diffuse reflectance spectra (DRS). The photocatalytic properties of the materials were investigated by the decomposition of the methylene blue (MB) dye solution under ultraviolet light. The results show that the size of Cu-ZnO nanorods was reduced when the Cu<sup>2+</sup> doping ratio increased from 2 mol.% to 7 mol.%. The decomposition efficiency of the MB dye solution reached 92% - 97%, corresponding to the Cu<sup>2+</sup> doping ratio changed from 2 - 7 mol.% (after 40 minutes of ultraviolet irradiation). The highest efficiency for the decomposition of the MB solution was obtained at a Cu<sup>2+</sup> doping ratio of 2 mol.%.
基金Founded by the Foundation of Shaanxi Province Key Provence Research and Development(No.2022GY-163)the Foundation of Xianyang City Key Research and Development(No.2021ZDYFGY-0038)+1 种基金the Foundation of Shaanxi Provincial Education Department(No.22JC020)the Key Laboratory of Sustained Utilization&Development of Water Recourse of Hebei Province(Hebei Geo University)(No.HSZYL2021002)。
文摘The coal gangue as the only source of silicon and aluminum was employed to synthesize sodalite and faujasite using hydrothermal method,which directly treated the mixture of pre-treated coal gangue and NaOH solution under hydrothermal environment.X-ray powder diffraction analysis(XRD),thermogravimetry analysis(TG)and differential thermogravimetry analysis(DTG),scanning electron microscopy(SEM),high resolution transmission electron microscopy(HRTEM),N_(2)adsorption-desorption technique,X-ray photoelectron spectroscopy(XPS),etc.were used to characterize the samples.Cd^(2+) ion was used to evaluate the heavy metal ions removal performance of the samples.The experimental results show that the coal gangue,which consists of quartz,calcium feldspar,potassium feldspar and kaolinite,can transform to sodalite and faujasite under alkali-hydrothermal condition at 150 and 180℃,respectively.The as-prepared sodalite and faujasite can effectively remove the simulated Cd2+ion wastewater and actual industrial wastewater containing As^(3+),Cd^(2+),and Cr^(3+)ions,and the good heavy metal ion removal performance of the zeolites is mainly attributed to their low Si/Al ratio and high Na+content.This alkali-hydrothermal method appears to be a simple and efficient method for transformation of coal gangue to high purity zeolites.
基金supported by Chongqing Newcent New Materials Co.,Ltd.,China (No.2021GKF-0708).
文摘Tetragonal barium titanate was synthesized from barium hydroxide octahydrate and titanium tetrachloride through a simple one-step hydrothermal method.The effect of different solvents on the crystal structure and morphology of barium titanate nanoparticles during the hy-drothermal process was investigated.Except for ethylene glycol/water solvent,impurity-free barium titanate was synthesized in pure water,methanol/water,ethanol/water,and isopropyl alcohol/water mixed solvents.Compared with other alcohols,ethanol promotes the formation of a tetragonal structure.In addition,characterization studies confirm that particles synthesized in methanol/water,ethanol/water,and isopropyl al-cohol/water mixed solvents are smaller in size than those synthesized in pure water.In the case of alcohol-containing solvents,the particle size decreases in the order of isopropanol,ethanol,and methanol.Among all the media used in this study,ethanol/water is considered the optimum reaction media for barium titanate with high tetragonality(defined as the ratio of two lattice parameters c and a,c/a=1.0088)and small aver-age particle size(82 nm),which indicates its great application potential in multilayer ceramic capacitors.
文摘LiCoPO4 micron-rods with an average diameter of about 500 nm and length of about 5 μm were synthesized by dispersant-aided hydrothermal method. Poly(n-vinylpyrrolidone) (PVP) was used as dispersant in the hydrothermal method. The starting solution and the concentration of dispersant have significant influences on the morphology of LiCoPO4,and the electrochemical performance is improved via controlling the particle size and morphology by the hydrothermal method. The cell using smaller particle LiCoPO4 as cathode delivers a larger capacity and lower cell polarization.
基金the financial support from the Ministry of Science and Technology,Taiwan(MOST 104-2218-E-033-006-MY2)
文摘NaTaO_(3-x)N_x catalysts were synthesized by a hydrothermal(H) and a solid-state(S) methods in this study.The H-and S-NaTaO_(3-x)N_x samples were characterized by X-ray diffraction(XRD), scanning electron microscopy(SEM), transmission electron microscopy(TEM), UV–visible(UV–vis) diffuse reflectance spectroscopy, and photoluminescence(PL) spectroscopy. The XRD patterns of the H-and S-samples showed peaks indexed to the pure phase of perovskite NaTaO_3 and minor peaks assignable to Ta_3N_5 at various synthesis temperatures. Substitution of oxygen by nitrogen ions causes the light absorption of the H-and S-NaTaO_(3-x)N_x samples to be extended to the 600–650 nm region, thus making the samples visible-light active. The NaTaO_(3-x)N_x samples exhibited photocatalytic activity for H_2 and O_2 evolution from aqueous methanol and silver nitrate solutions under visible-light irradiation. The UV–vis and PL spectra of the Hand S-catalysts revealed the presence of cationic vacancies and reduced metallic species, which acted as recombination centers. These results demonstrated that the preparation method plays a critical role in the formation of defect states, thereby governing the photocatalytic activity of the NaTaO_(3-x)N_x catalysts.
基金financially supported by the National Natural Science Foundation of China (No. 51474028)the National Key Research and Development Program of China (No. 2017YFC0210301)+1 种基金China Postdoctoral Science Foundation (No. 2017M621034)the Science and Technology Benefiting Citizens Program of Ningbo, China (No. 2015C50058)
文摘Hydro-sodalites are zeolitic materials with a wide variety of applications.Fly ash is an abundant industrial solid waste,rich in silicon and aluminum,from which hydro-sodalite can be synthesized.However,traditional hydrothermal synthesis methods are complex and cannot produce high-purity products.Therefore,there is a demand for processing routes to obtain high-purity hydro-sodalites.In the present study,high-purity hydro-sodalite(90.2 wt%)was prepared from fly ash by applying a hydrothermal method to a submolten salt system.Samples were characterized by powder X-ray diffraction(XRD),scanning electron microscopy(SEM),thermogravimetry and differential thermal analysis(TG–DTA),and Fourier transform infrared spectroscopy(FTIR)to confirm and quantify conversion of the raw material into the product phase.Purity of the samples prepared with an H2O/Na OH mass ratio of 1.5 and an H2O/fly ash mass ratio of 10 was calculated and the conversion process of the product phase was studied.Crystallinity of the product was influenced more by the Na OH concentration,less by the H2O/fly ash mass ratio.The main reaction process of the system is that the Si O ions produced by dissolution of the vitreous body in the fly ash and Na+ions in the solution reacted on the destroyed mullite skeleton to produce hydro-sodalite.This processing route could help mitigate processing difficulties,while producing high-purity hydro-sodalite from fly ash.
基金financial support from the Swedish Innovation Agency(VINNOVA)and China Scholarship Council(CSC).
文摘α-calcium sulfate hemihydrate (α-HH) is known to be suitable for application as bone void filler. High percentage of α-HH is obviously needed for medical applications, especially for implantation. Three commercially available calcium sulfate dihydrates (DH, CaSO4·2H2O) with different sizes and surface morphologies were used as starting materials to synthesize high percentage α-HH via a hydrothermal method. The median particle sizes of the three types of DH were 946.7 μm, 162.4 μm and 62.4 μm, respectively. They were named as DH-L, DH-M and DH-S in this paper. The particle size distribution, morphology and phase composition of the raw materials were evaluated before synthesis. SEM results revealed that DH-L consisted of irregular large particles, while DH-M and DH-S were composed of plate-like particles with some small ones. High percentage HH can be obtained with proper synthesis parameters by hydrothermal method, specifically, 105 °C/90 min for DH-L (achieving 98.8% HH), 105°C/30 min for DH-M (achieving 96.7% HH) and 100°C/45 min for DH-S (achieving 98.4% HH). All the synthesized HH were hexagonal columns, demonstrating that they were α-phase HH. The particle size and morphology of starting material (DH) have significant influences on not only the rate of phase transition but also the morphology of the synthesized α-HH. Calcium sulfate dihydrate cements were prepared by the synthesized α-HH. The highest compressive strength of calcium sulfate dihydrate cement was 17.2 MPa. The results show that the preparation of high percentage α-HH is feasible via a hydrothermal method and the process can be further scaled up to industrial scale production.
基金Projects(20601012,20601016,20961005)supported by the National Natural Science Foundation of ChinaProject(209024)supported by the Ministry of Education of ChinaProjects(206077,206043,10013-121008)supported by Inner Mongolia University,China
文摘A microemulsion-mediated hydrothermal method for synthesis of YVO4:RE(RE=Yb 3+/Er 3+,Yb 3+/Tm 3+)nanoparticles by hydrothermal treatment of quaternary microemulsion medium consisting of Na3VO4/NaOH and RE(NO3)3 aqueous solution, surfactant cetyltrimethylammonium bromide(CTAB),cosurfactant n-hexanol and oil phase n-heptane was report.The confinement of microemulsion droplets acting as microreactors during the reaction process allows the formation of small size YVO4:RE nanoparticles with relatively narrow size distribution and less aggregation.The structure,size and shape of YVO4:RE nanoparticles were investigated by means of X-ray diffractometry(XRD)and transmission electron microscopy(TEM).Compared with the conventional solid annealing diffusion method,the microemulsion-mediated hydrothermal method shows superiority in obtaining YVO4:RE nanoparticles with controllable size,narrow size distribution and less aggregation.The microemulsion-mediated hydrothermal method may be potentially applicable for synthesis of other rare earth doped up-converting luminescence nanomaterials.
文摘Vertically oriented ZnO nanorods have been synthesized by hydrothermal method on quartz substrates with a seed layer. The influence of solution concentration on the morphology, structural and optical properties was analyzed. Results indicated that with the increase of solution concentration, the diameter and uniformity of ZnO nanorods increased. And the preferred orientation is obviously which shows better crystal quality. Typically, when the solution concentration is 0.03 mol/L, the nanorods exhibit a stronger UV emission peak located around 380 nm. In the visible region, all synthesized samples demonstrate more than 80% of optical transparency.
文摘Hydrothermal method was used to synthesize nanoscale particles of MnZn ferrites. The crystallites were characterized by XRD, TEM and SEM. The effects of the reaction time, temperature and additives on the product were investigated. Crystallization process would be carried out above 160 ℃ for 5 h or more, higher temperature can reduce the reaction time. Additives were used to remove impurities such as Fe 2O 3, ZnMnO 3.10～15 nm pure slightly agglomerated MnZn ferrite crystallites with a narrow grain size distribution were obtained.
文摘Magnesium hydroxide(Mg(OH)_2) nanorods were synthesized by a simple and facile hydrothermal method in the presence of cetyltetramethylammonium bromide(CTAB) as a surfactant. Nanorods of magnesium oxide Mg O were also induced by thermal decomposition of Mg(OH)_2 nanorods at 700. By using disk diffusion technique, the Mg(OH)_2 nanorods were found to exhibit higher antibacterial efficiency against several tested bacterial strains.
基金support from the National Natural Science and Henan Province United Foundation of China (No. U1204601)Natural Science Foundation of Henan Province (No. 122300410298)+1 种基金Natural Science Foundation of Education Department of Henan Province (No. 13A480365)PhD Foundation of Zhengzhou University of Light Industry (No. 2010BSJJ029)
文摘In this paper, we have demonstrated a facile and low-cost synthesis of the ZnO/CuO nanocomposites by two-step hydrothermal methods. The photocatalytic properties of the as-synthesized ZnO/CuO nanocomposites have been evaluated by the photodegradation of methylene blue(MB) and methyleneorange(MO) under UV irradiation. Experimental results show that MB and MO can be degraded completely within 15 and 25 min by the ZnO/CuO nanocomposites and its photodegradation rate is 6 times faster than that of pure ZnO. This enhanced photocatalytic activity can be ascribed to the low recombination probability of photo-induced carriers due to the efficient charge transfer in the nanocomposites. The as-synthesized ZnO/CuO nanocomposite may be a promising candidate for dye photodegradation of wastewaters.
基金Supported by the National Basic Research Program of China("973"Program,No.2014CB239300,No.2012CB720100)National Natural Science Foundation of China(No.21406164,No.21466035)
文摘TiO_2 nanoparticles(NPs)were prepared via the hydrothermal route of TiO_2 xerogel in nitric acid, hydrochloric acid and acetic acid. The physico-chemical properties of the powders were characterized by X-ray diffraction(XRD)and N_2 adsorption desorption techniques. The effects of the different acids on the structure(crystal phase)and texture(primary particle size and porosity)of the TiO_2 powders were explored. Results indicated that acetic acid facilitated the formation and stability of pure anatase phase. On the other hand, nitric acid and hydrochloric acid led to the transformation from anatase to rutile. The catalyst synthesized via the hydrothermal route of TiO_2 xerogel in the low concentration hydrochloric acid solution(Ti-HCl-0.15)had the highest photocatalytic activity than the catalysts obtained in the other two acid solutions. The effects of the different acids were discussed in terms of acid strength, chelating effect and the thermal stability of the adsorbed acidic anions.
基金Financial support from the Foundation(No.KF201607)of the Key Laboratory of Pulp and Paper Science and Technology of the Ministry of Education/Shandong Province of China
文摘The aim of this study was to investigate the hemicelluloses extracted from Populus tomentosa Carr.by the hydrothermal method with ethanol.The influence of ethanol concentration on the hemicellulosic fractions was systematically studied.The chemical compositions and structural features of the hemicellulosic fractions were investigated by a combination of sugar analysis,gel-permeation chromatography,Fourier transform infrared spectroscopy,and one-dimensional proton and carbon-13 nuclear magnetic resonance,and two-dimensional heteronuclear single quantum coherence spectroscopy.Neutral sugar analysis of the hemicellulosic fractions revealed that a higher ethanol concentration(45%~80%) favored the isolation of hemicelluloses with more side chains and lower glucose contents.The molecular weights of these polysaccharides ranged between 2842 g/mol and 5101 g/mol.The results of this study indicate that the hydrothermal ethanol process provides a new pretreatment strategy for the isolation and extraction of biomass.
基金supported by the Natural Sciences and Engineering Research Council(NSERC)of CanadaThe financial support of the State Scholarship Fund of China(No.201506160061)
文摘The resistive switching characteristics of TiO_2 nanowire networks directly grown on Ti foil by a single-step hydrothermal technique are discussed in this paper. The Ti foil serves as the supply of Ti atoms for growth of the TiO_2 nanowires, making the preparation straightforward. It also acts as a bottom electrode for the device. A top Al electrode was fabricated by e-beam evaporation process. The Al/TiO_2 nanowire networks/Ti device fabricated in this way displayed a highly repeatable and electroforming-free bipolar resistive behavior with retention for more than 10~4 s and an OFF/ON ratio of approximately 70. The switching mechanism of this Al/TiO_2 nanowire networks/Ti device is suggested to arise from the migration of oxygen vacancies under applied electric field. This provides a facile way to obtain metal oxide nanowire-based Re RAM device in the future.
文摘High quality potassium hexatitanate whiskers were hydrothermally synthesized in one step under moderate temperature and pressure condi-tions. Effects of the titanium source and reaction conditions on the hydrothermal reaction rate, product phase component, and morphology of whiskers were investigated. The results show that the reactivity of hydrated titania, anatase TiO2, and rutile TiO2 with KOH decreases in turn, and with hydrated titania as titanium source, it is difficult to obtain potassium hexatitanate whiskers with good morphology. In contrast, uni-form potassium hexatitanate whiskers with a length of 10-20 μm and a diameter of 200-700 nm were obtained using anatase TiO2 as titanium source. The investigation demonstrates that the initial KOH concentration, annealing temperature and time, molar ratio of K2O/TiO2, etc. sig-nificantly affect the morphology of the as-synthesized whiskers. The optimized synthesis condition is as follows: anatase as a titanium source; 10 wt.% KOH solution; annealing temperature and time of 300°C and 5 h, respectively; K2O/TiO2 molar ratio of 5, etc. A rhombic potassium hexatitanate was prepared under the optimum condition and the whisker grew along the [110] direction. The reaction mechanism was dis-cussed.
基金Project supported bythe Key Laboratory of Rare Earth Chemistry and Physics ,ChangchunInstitute of Applied Chemistry ,Chinese Academy of Sciences (R020202K)
文摘Nanocrystal of upconversion （UC） phosphor Ho 3+ , Tm 3+ , and Yb 3+ co-doped NaYF4 was prepared by the hydrothermal method in the presence of the complexing agent EDTA. Under 980 nm diode laser excitation, the impact of different concentrations of Ho 3+ ion on the UC luminescence intensity was discussed. The law of luminescence intensity versus pump power shows that the 474 nm blue emission, 538 nm green emission, and 642 nm red emission are all due to the two-photon process, while the 450 nm blue emission is a three-photon process. The UC mechanism and processes were also analyzed. The sample was characterized by transmission electron microscopy （TEM） and X-ray diffraction （XRD）. The result shows that Ho 3+ , Tm 3+ , and Yb 3+ co-doped NaYF4 prepared by the hydrothermal method exhibits a hexagonal nanocrystal.
基金This work was supported in part by NSF of Guangdong Province,the Most Important Items of the Tenth Five-Year Plan of Guangdong Provincethe Project of Science and Technology Program of Guangdong Province+1 种基金the Project of Science and Technology Program of Guangzhou Citythe Maoming Science Technology Fund of Guangdong Province.
文摘The Ni(OH)2/SiO2 binary colloid was prepared using Ni(NO3)2.6H2O and (C2H5 O)4SiO4 as starting materials and was used to form NiO/SiO2 composite powder by hydrothermal method and desiccant method in open air respectively. Multiwalled carbon nanotubes (MWCNTs) were synthesized respectively by chemical vapor deposition using the NiO/SiO2 catalyst prepared by different methods. The phase and morphology of the catalysts and the morphology, output yield and purity of MWCNTs were compared by XRD, TEM and SEM. The results show that the catalyst powder prepared by hydrothermal method, compared with that by desiccant method, is smaller, better dispersion and has stronger catalytic activity. Pure MWCNTs with smaller tube diameter and narrow range could be obtained at a high yield using that NiO/SiO.2 powder prepared by hydrothermal method as catalyst.
文摘Semiconducting zinc oxide (ZnO) nanorods were obtained in bulk quantity by an hexamethylenetetramine (HMTA)-assisted hydrothermal method at low temperature (90°C) with methenamine ((CH3)6N4 as surfactant and catalyst and zinc nitrate Zn(NO3)2·6H2O as Zn source. The structure and phase of ZnO nanorods were studied using x-ray diffraction (XRD) and high resolution transmission electron microscopy techniques (HRTEM). The morphology of the nanostructures was studied by scanning electron microscope (SEM) method. The photoluminescence (PL) properties were investigated founding two emission bands under UV excitation.
